INTEGRATED CIRCUITS DIVISION
www.ixysic.com
DS-LAA110L-R09 1
LAA110L
Dual Single-Pole, Current-Limited
OptoMOS® Relay
e3
Pb
Part # Description
LAA110L 8-Pin DIP (50/Tube)
LAA110LS 8-Pin Surface Mount (50/Tube)
LAA110LSTR 8-Pin Surface Mount (1,000/Reel)
LAA110PL 8-Pin Flat Pack (50/Tube)
LAA110PLTR 8-Pin Flat Pack (1,000/Reel)
Parameter Ratings Units
Blocking Voltage 350 VP
Load Current 120 mArms / mADC
On-Resistance (max) 35
Applications
Features
Description
Approvals
Ordering Information
Pin Configuration
Switching Characteristics of
Normally Open (Form A) Devices
3750Vrms Input/Output Isolation
Current Limiting Device
Low Drive Power Requirements (TTL/CMOS
Compatible)
No Moving Parts
High Reliability
Arc-Free With No Snubbing Circuits
No EMI/RFI Generation
Machine Insertable, Wave Solderable
Surface Mount and Tape & Reel Versions Available
Small 8-Pin Package
Telecom Switching
Tip/Ring Circuits
Modem Switching (Laptop, Notebook, Pocket Size)
Hook Switch
Dial Pulsing
Ground Start
Ringing Injection
Instrumentation
Multiplexers
Data Acquisition
Electronic Switching
I/O Subsystems
Meters (Watt-Hour, Water, Gas)
Medical Equipment-Patient/Equipment Isolation
Security
Aerospace
Industrial Controls
LAA110L is a dual normally open (1-Form-A) Solid
State Relay that has two independently controlled,
optically coupled MOSFET switches with an additional
current limiting circuit. The MOSFET switches and
photovoltaic die use optically coupled MOSFET
technology to provide 3750Vrms of input/output
isolation.
The optically coupled outputs, which use the patented
OptoMOS architecture, are controlled by a highly
efficient GaAIAs infrared LED.
This dual switch OptoMOS relay provides a more
compact design solution than discrete single-pole
relays in a variety of applications, and saves board
space by incorporating both switches in a single 8-Pin
package.
UL Recognized Component: File # E76270
CSA Certified Component: Certificate # 1175739
EN/IEC 60950-1 Certified Component:
TUV Certificate B 09 07 49410 004
Form-A
IF
ILOAD
10%
90%
ton toff
1
2
3
4
8
7
6
5
+ Control - Switch #1
– Control - Switch #1
+ Control - Switch #2
– Control - Switch #2
Load - Switch #1
Load - Switch #1
Load - Switch #2
Load - Switch #2
INTEGRATED CIRCUITS DIVISION
www.ixysic.com
2R09
LAA110L
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Parameter Conditions Symbol Min Typ Max Units
Output Characteristics
Load Current, Continuous 1-I
L- - 120 mArms / mADC
Load Current Limiting VL=8V, IF=5mA ICL ±130 ±170 ±210 mA
On-Resistance 2IL=120mA RON -3035
Off-State Leakage Current VL=350VPILEAK --1 A
Switching Speeds
Turn-On IF=5mA, VL=10V ton --3 ms
Turn-Off toff --3 ms
Output Capacitance VL=50V, f=1MHz COUT -25- pF
Input Characteristics
Input Control Current to Activate IL=120mA IF--5 mA
Input Control Current to Deactivate - - 0.4 0.7 - mA
Input Voltage Drop IF=5mA VF0.9 1.2 1.4 V
Reverse Input Current VR=5V IR--10 A
Common Characteristics
Input to Output Capacitance - CI/O -3- pF
1 If both poles operate, then the load current must be derated so that it does not exceed the package power dissipation value.
2 Measurement taken within one second of on-time.
Parameter Ratings Units
Blocking Voltage 350 VP
Reverse Input Voltage 5 V
Input Control Current 50 mA
Peak (10ms) 1 A
Input Power Dissipation 1150 mW
Total Power Dissipation 2800 mW
Isolation Voltage, Input to Output 3750 Vrms
Operational Temperature -40 to +85 °C
Storage Temperature -40 to +125 °C
1 Derate linearly 1.33 mW / ºC
2 Derate linearly 6.67 mW / ºC
Absolute Maximum Ratings @ 25ºC
Electrical Characteristics @ 25ºC
INTEGRATED CIRCUITS DIVISION
LAA110L
www.ixysic.com 3
R09
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
35
30
25
20
15
10
5
0
1.17 1.19 1.21 1.23 1.25
LED Forward Voltage Drop (V)
Device Count (N)
Typical Turn-On Time
(N=50, IF=5mA, IL=120mADC)
0.15 0.35 0.55 0.750.25 0.45 0.65
Turn-On Time (ms)
Device Count (N)
25
20
15
10
5
0
Device Count (N)
25
20
15
10
5
0
Typical Turn-Off Time
(N=50, IF=5mA, IL=120mADC)
0.025 0.125
0.225
0.1750.075
Turn-Off Time (ms)
Typical IF for Switch Operation
(N=50, IL=120mADC)
0.75 1.35 1.950.45 1.05 1.65 2.25
LED Current (mA)
Device Count (N)
25
20
15
10
5
0
Typical IF for Switch Dropout
(N=50, IL=120mADC)
25
20
15
10
5
0
0.75 1.35 1.950.45 1.05 1.65 2.25
LED Current (mA)
Device Count (N)
Typical On-Resistance Distribution
(N=50, IF=5mA, IL=120mADC)
35
30
25
20
15
10
5
0
17.0 17.8 18.6 19.417.4 18.2 19.0
On-Resistance (:)
Device Count (N)
Typical Blocking Voltage Distribution
(N=50)
35
30
25
20
15
10
5
0
376.3 389.3 402.3 415.3382.8 395.8 408.8
Blocking Voltage (VP)
Device Count (N)
Typical LED Forward Voltage Drop
vs. Temperature
Temperature (ºC)
LED Forward Voltage Drop (V)
1.8
1.6
1.4
1.2
1.0
0.8
-40 -20 0 20 40 60 80 120100
I
F
=50mA
I
F
=30mA
I
F
=20mA
I
F
=10mA
I
F
=5mA
Typical Turn-On Time
vs. LED Forward Current
(IL=120mADC)
LED Forward Current (mA)
Turn-On Time (ms)
05 1015202530354045
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
50
Typical Turn-Off Time
vs. LED Forward Current
(IL=120mADC)
LED Forward Current (mA)
Turn-Off Time (ms)
05 1015202530354045
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
50
INTEGRATED CIRCUITS DIVISION
www.ixysic.com
4R09
LAA110L
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
Typical Turn-On Time
vs. Temperature
(IL=120mADC)
Temperature (ºC)
IF=10mA
IF=20mA
Turn-On Time (ms)
-40
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
-20 0 20 40 60 80 100
IF=5mA
Typical Turn-Off Time
vs. Temperature
(IF=5mA, IL=120mADC)
Temperature (ºC)
Turn-Off Time (ms)
-40
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-20 0 20 40 60 80 100
Typical On-Resistance vs. Temperature
(IF=5mA, IL=120mADC)
Temperature (ºC)
On-Resistance (:)
-40
60
50
40
30
20
10
0
-20 0 20 40 60 80 100
Typical IF for Switch Operation
vs. Temperature
(IL=120mADC)
Temperature (ºC)
LED Current (mA)
-40
3.0
2.5
2.0
1.5
1.0
0.5
0
-20 0 20 40 60 80 100
Typical IF for Switch Dropout
vs. Temperature
(IL=120mADC)
Temperature (ºC)
LED Current (mA)
-40
3.0
2.5
2.0
1.5
1.0
0.5
0
-20 0 20 40 60 80 100
Typical Load Current vs. Load Voltage
(IF=5mA)
Load Voltage (V)
Load Current (mA)
150
100
50
0
-50
-100
-150
-3 -2 -1 0 1 2 3
Typical Blocking Voltage
vs. Temperature
Temperature (ºC)
Blocking Voltage (VP)
-40
420
410
400
390
380
370
360
-20 0 20 40 60 80 100
Typical Leakage vs. Temperature
Measured across Pins 5&6, 7&8
Temperature (ºC)
Leakage (nA)
-40
16
14
12
10
8
6
4
2
0
-20 0 20 40 60 80 100
Typical Current Limiting
vs. Temperature
(IF=5mA)
Temperature (ºC)
Current (mA)
-40
250
200
150
100
50
0
-20 0 20 40 60 80 100
350
300
Maximum Load Current
vs. Temperature
Temperature (ºC)
Load Current (mA)
180
160
140
120
100
80
60
40
20
0
-40 -20 0 20 40 60 80 120100
IF=10mA
IF=5mA
INTEGRATED CIRCUITS DIVISION
LAA110L
www.ixysic.com 5
R09
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device Moisture Sensitivity Level (MSL) Rating
LAA110L / LAA110LS / LAA110PL MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device Maximum Temperature x Time
LAA110L / LAA110LS 250ºC for 30 seconds
LAA110PL 260ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
e3
Pb
INTEGRATED CIRCUITS DIVISION
www.ixysic.com
6R09
LAA110L
MECHANICAL DIMENSIONS
Dimensions
mm
(inches)
PCB Hole Pattern
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
9.144 ± 0.508
(0.360 ± 0.020)
0.457 ± 0.076
(0.018 ± 0.003)
9.652 ± 0.381
(0.380 ± 0.015)
7.239 TYP.
(0.285)
7.620 ± 0.254
(0.300 ± 0.010)
4.064 TYP
(0.160)
0.813 ± 0.102
(0.032 ± 0.004)
8-0.800 DIA.
(8-0.031 DIA.) 2.540 ± 0.127
(0.100 ± 0.005)
7.620 ± 0.127
(0.300 ± 0.005)
7.620 ± 0.127
(0.300 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
Pin 1
0.254 ± 0.0127
(0.010 ± 0.0005)
Dimensions
mm
(inches)
PCB Land Pattern
2.540 ± 0.127
(0.100 ± 0.005)
9.652 ± 0.381
(0.380 ± 0.015)
6.350 ± 0.127
(0.250 ± 0.005)
9.525 ± 0.254
(0.375 ± 0.010)
0.457 ± 0.076
(0.018 ± 0.003)
0.813 ± 0.102
(0.032 ± 0.004)
4.445 ± 0.127
(0.175 ± 0.005)
7.620 ± 0.254
(0.300 ± 0.010)
0.635 ± 0.127
(0.025 ± 0.005)
0.254 ± 0.0127
(0.010 ± 0.0005)
2.54
(0.10)
8.90
(0.3503)
1.65
(0.0649)
0.65
(0.0255)
3.302 ± 0.051
(0.130 ± 0.002)
Pin 1
Dimensions
mm
(inches)
PCB Land Pattern
9.398 ± 0.127
(0.370 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
2.540 ± 0.127
(0.100 ± 0.005)
7.620 ± 0.254
(0.300 ± 0.010)
0 MIN / 0.102 MAX
(0 MIN / 0.004 MAX)
2.286 MAX.
(0.090 MAX.)
0.203 ± 0.013
(0.008 ± 0.0005)
0.635 ± 0.127
(0.025 ± 0.005)
9.652 ± 0.381
(0.380 ± 0.015)
0.457 ± 0.076
(0.018 ± 0.003)
2.159 ± 0.025
(0.085 ± 0.001)
2.54
(0.10)
8.70
(0.3425)
1.55
(0.0610)
0.65
(0.0255)
0.864 ± 0.120
(0.034 ± 0.004)
Pin 1
LAA110L
LAA110LS
LAA110PL
INTEGRATED CIRCUITS DIVISION
Specification: DS-LAA110L-R09
©Copyright 2012, IXYS Integrated Circuits Division
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
12/19/2012
For additional information please visit our website at: www.ixysic.com
7
LAA110L
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
MECHANICAL DIMENSIONS
LAA110PLTR Tape & Reel
LAA110LSTR Tape & Reel
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
Embossment
Embossed Carrier
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
330.2 DIA.
(13.00 DIA.)
User Direction of Feed
P = 12.00
(0.472)
W = 16.00
(0.63)
Bo = 10.30
(0.406)
Ao = 10.30
(0.406)
K1 = 2.00
(0.079)
K0 = 2.70
(0.106)
7.50
(0.295)
2.00
(0.079)
4.00
(0.157)
Dimensions
mm
(inches)
User Direction of Feed
NOTES:
1. Dimensions carry tolerances of EIA Standard 481-2
2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
Embossment
Embossed Carrier
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
330.2 DIA.
(13.00 DIA.)
K1
=4.20
(0.165)
0
K =4.90
(0.193)
P=12.00
(0.472)
W=16.00
(0.63)
Bo=10.30
(0.406)
Ao=10.30
(0.406)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
IXYS:
LAA110P LAA110S LAA110L LAA110LSTR LAA110LS LAA110PTR LAA110 LAA110STR LAA110PLTR
LAA110PL