CS5467 Four-channel Power/Energy IC Features & Description Description * Energy Linearity: 0.1% of Reading over 1000:1 Dynamic Range * On-chip Functions: The CS5467 is a watt-hour meter on a chip. It measures line voltage and current and calculates active, reactive, apparent power, energy, power factor, and RMS voltage and current. - Voltage and Current Measurement Active, Reactive, and Apparent Power/Energy RMS Voltage and Current Calculations Current Fault and Voltage Sag Detection Calibration Phase Compensation Temperature Sensor Energy Pulse Outputs * * * * * * * Meets Accuracy Spec for IEC, ANSI, & JIS Low Power Consumption Voltage Tamper Correction Ground-referenced Inputs with Single Supply On-chip 2.5 V Reference (40 ppm / C typ.) Power Supply Monitor Function Three-wire Serial Interface to Microcontroller or E2PROM * Power Supply Configurations GND: 0 V, VA+: +5 V, VD+: +3.3 V to +5 V An internal RMS voltage reference can be used if voltage measurement is disabled by tampering. Four analog-to-digital converters are used to measure two voltages and two currents. Optionally, voltage2 channel can be used for temperature measurement. The CS5467 is designed to interface to a variety of voltage and current sensors. Additional features include system-level calibration, voltage sag and current fault detection, peak detection, phase compensation, and energy pulse outputs. ORDERING INFORMATION See Page 45. RESET VA+ IIN1+ IIN1- PGA 4th Order Modulator Digital Filter VD+ HPF Option MODE CS SDI VIN1+ VIIN1- x10 2nd Order Modulator Digital Filter HPF Option Serial Interface Power Calculation Engine IIN2+ IIN2- VIN2+ VIN2- VREFIN VREFOUT INT PGA 4th Order Modulator Digital Filter HPF Option E-to-F x10 2nd Order Modulator Digital Filter HPF Option Calibration Temperature Sensor System Clock E1 E2 E3 x1 Voltage Reference AGND http://www.cirrus.com SDO SCLK Power Monitor PFMON Clock Generator /K XIN Copyright Cirrus Logic, Inc. 2011 (All Rights Reserved) XOUT CPUCLK DGND JAN `11 DS714F3 CS5467 TABLE OF CONTENTS 1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Control Pins and Serial Data I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Analog Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Characteristics & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Analog Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Analog Inputs (All Inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Analog Inputs (Current Inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Analog Inputs (Voltage Inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Voltage Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Reference Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Reference Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Digital Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Master Clock Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Input/Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Serial Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SDI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SDO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 E2PROM mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 E1, E2, and E3 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. Signal Path Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Analog-to-Digital Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Decimation Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Phase Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 DC Offset and Gain Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 High-pass Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6 Low-Rate Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 RMS Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8 Power and Energy Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9 Peak Voltage and Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10 Power Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Analog Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.1 Voltage1 & Voltage2 Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.2 Current1 & Current2 Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.3 Power Fail Monitor Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 13 14 14 14 14 15 15 15 15 16 17 17 18 18 18 18 18 DS714F3 CS5467 5.1.4 Voltage Reference Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.5 Voltage Reference Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.6 Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Digital Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.1 Reset Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2 CPU Clock Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.3 Interrupt Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.4 Energy Pulse Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.5 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Setting Up the CS5467 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 Clock Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 CPU Clock Inversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Interrupt Pin Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Current Input Gain Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 High-pass Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 Cycle Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 Energy Pulse Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 No Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.9 Energy Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10 Energy Pulse Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.11 Voltage Sag/Current Fault Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12 Epsilon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.13 Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Using the CS5467 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Power-down States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Voltage Tamper Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Command Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Register Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Page Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Page 0 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Page 1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Page 2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Page 5 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9. System Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.1 Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.1.1 DC Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.1.2 AC Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.2 Gain Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.2.1 AC Gain Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.2.2 DC Gain Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DS714F3 18 18 18 18 18 18 18 18 19 20 20 20 20 20 20 20 20 21 21 21 21 22 22 23 23 23 23 24 24 25 29 29 29 34 39 39 40 40 40 40 40 41 41 41 3 CS5467 9.1.3 Calibration Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.4 Temperature Sensor Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1.4.1 Temperature Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . 9.1.4.2 Temperature Gain Calibration . . . . . . . . . . . . . . . . . . . . . . . . 10. E2PROM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 E2PROM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 E2PROM Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Which E2PROMs Can Be Used? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11. Basic Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. Environmental, Manufacturing, & Handling Information . . . . . . . . . . . . . . . . . 15. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 41 41 41 42 42 42 42 43 44 45 45 46 LIST OF FIGURES Figure 1. CS5467 Read and Write Timing Diagrams ................................................................. 12 Figure 2. Timing Diagram for E1, E2, and E3 .............................................................................. 13 Figure 3. Signal Flow for V1, I1, P1, Q1 Measurements ............................................................ 14 Figure 4. Signal Flow for V2, I2, P2, Q2 Measurements ............................................................ 14 Figure 5. Low-rate Calculations .................................................................................................. 16 Figure 6. Two-channel Power Summation.................................................................................. 16 Figure 7. Oscillator Connections................................................................................................. 18 Figure 8. Sag and Fault Detect................................................................................................... 22 Figure 9. Fixed RMS Voltage Selection...................................................................................... 23 Figure 10. Calibration Data Flow ................................................................................................ 40 Figure 11. System Calibration of Offset...................................................................................... 40 Figure 12. System Calibration of Gain........................................................................................ 41 Figure 13. Typical Interface of E2PROM to CS5467 .................................................................. 42 Figure 14. Typical Connection Diagram ..................................................................................... 43 LIST OF TABLES Table 1. Interrupt Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 2. Current Input Gain Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 3. High-pass Filter Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 4. E2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 5. E3 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 6. E1 / E2 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 7. E3 Pin with E1MODE enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 20 20 20 20 21 21 21 DS714F3 CS5467 1. OVERVIEW The CS5467 is a CMOS power measurement integrated circuit utilizing four analog-to-digital converters to measure two line voltages and two currents. Optionally, voltage2 channel can be used for temperature measurement. It calculates active, reactive, and apparent power as well as RMS and peak voltage and current. It handles other system-related functions, such as pulse output conversion, voltage sag, current fault, voltage zero crossing, line frequency, and voltage tamper correction. The CS5467 is optimized to interface to current transformers or shunt resistors for current measurement, and to resistive dividers or voltage transformers for voltage measurement. Two full-scale ranges are provided on the current inputs to accommodate both types of current sensors. The CS5467's four differential inputs have a common-mode input range from analog ground (AGND) to the positive analog supply (VA+). An additional analog input (PFMON) is provided to allow the application to determine when a power failure is in progress. By monitoring the unregulated power supply, the application can take any required action when a power loss occurs. An on-chip voltage reference (nominally 2.5 volts) is generated and provided at analog output, VREFOUT. This reference can be supplied to the chip by connecting it to the reference voltage input, VREFIN. Alternatively, an external voltage reference can be supplied to the reference input. Three digital outputs (E1, E2, E3) provide a variety of output signals and, depending on the mode selected, provide energy pulses, power failure indication, or other choices. The CS5467 includes a three-wire serial host interface to an external microcontroller or serial E2PROM. Signals include serial data input (SDI), serial data output (SDO), serial clock (SCLK), and optionally a chip select (CS), which allows the CS5467 to share the SDO signal with other devices. A MODE input is used to control whether an E2PROM will be used instead of a host microcontroller. DS714F3 5 CS5467 2. PIN DESCRIPTION Crystal Out CPU Clock Output Positive Digital Supply Digital Ground Serial Clock Serial Data Ouput Chip Select Mode Select Differential Voltage Input Differential Voltage Input Voltage Reference Output Voltage Reference Input Differential Voltage Input Differential Voltage Input XOUT CPUCLK VD+ DGND SCLK SDO CS MODE VIN1+ VIN1VREFOUT VREFIN VIN2+ VIN2- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 XIN SDI E2 E1 INT RESET E3 PFMON IIN1+ IIN1VA+ AGND IIN2+ IIN2- Crystal In Serial Data Input Energy Output 2 Energy Output 1 Interrupt Reset Energy Output 3 Power Fail Monitor Differential Current Input Differential Current Input Positive Analog Supply Analog Ground Differential Current Input Differential Current Input Clock Generator Crystal Out Crystal In 1,28 CPU Clock Output XOUT, XIN -- Connect to an external quartz crystal. Alternatively, an external clock can be supplied to the XIN pin to provide the system clock for the device. 2 CPUCLK -- Logic-level output from crystal oscillator. Can be used to clock an external CPU. Serial Clock 5 SCLK -- Clocks serial data from the SDI pin and to the SDO pin when CS is low. SCLK is a Schmitt-trigger input when MODE is low and a driven output when MODE is high. Serial Data Output 6 SDO -- Serial data output. Data is clocked out by SCLK. Chip Select 7 CS -- An input that enables the serial interface when MODE is low and a driven output when MODE is high. Mode Select 8 MODE -- High selects external E2PROM, Low selects external microcontroller. MODE includes a weak internal pull-down and therefore selects microcontroller mode if not connected. Control Pins and Serial Data I/O Energy Output 22, 25, E3, E1, E2 -- Primarily active-low energy pulse outputs. These can be programmed to output other conditions. 26 Reset 23 RESET -- An active-low Schmitt-trigger input used to reset the chip. Interrupt 24 INT -- Active-low output, indicates that an enabled condition has occurred. Serial Data Input 27 SDI -- Serial data input. Data is clocked in by SCLK. Analog Inputs/Outputs Differential Voltage Inputs 9,10 VIN1+, VIN1-, VIN2+, VIN2- -- Differential analog inputs for the voltage channels. 13, 14 Differential Current Inputs 20,19, IIN1+, IIN1-, IIN2+, IIN2- -- Differential analog inputs for the current channels. 16,15 Voltage Reference Output 11 VREFOUT -- The on-chip voltage reference output. Nominally 2.5 V, referenced to AGND. Voltage Reference Input 12 VREFIN -- The voltage reference input. Can be connected to VREFOUT or external 2.5 V reference. Power Supply Connections Positive Digital Supply 3 VD+ -- The positive digital supply. Digital Ground 4 DGND -- Digital ground. Positive Analog Supply 18 VA+ -- The positive analog supply. Analog Ground 17 AGND -- Analog ground. Power Fail Monitor 21 PFMON -- Used to monitor the unregulated power supply via a resistive divider. If the PFMON voltage drops below its low limit, the low-supply detect (LSD) bit is set in the Status register. 6 DS714F3 CS5467 3. CHARACTERISTICS & SPECIFICATIONS RECOMMENDED OPERATING CONDITIONS Parameter Positive Digital Power Supply Positive Analog Power Supply Voltage Reference Specified Temperature Range Symbol VD+ VA+ VREFIN TA Min 3.135 4.75 -40 Typ 5.0 5.0 2.5 - Max 5.25 5.25 +85 Unit V V V C ANALOG CHARACTERISTICS * * * * Min / Max characteristics and specifications are guaranteed over all Recommended Operating Conditions. Typical characteristics and specifications are measured at nominal supply voltages and TA = 25 C. VA+ = VD+ = 5 V 5%; AGND = DGND = 0 V; VREFIN = +2.5 V. All voltages with respect to 0 V. DCLK = 4.096 MHz. Parameter Accuracy Active Power (Note 1) Reactive Power (Note 1 and 2) Power Factor (Note 1 and 2) Current RMS (Note 1) Voltage RMS (Note 1) Symbol Min Typ Max Unit PACTIVE - 0.1 - % All Gain Ranges Input Range 0.1% - 100% QAVG - 0.2 - % All Gain Ranges Input Range 1.0% - 100% Input Range 0.1% - 1.0% PF - 0.2 0.27 - All Gain Ranges Input Range 1.0% - 100% Input Range 0.1% - 1.0% IRMS - 0.1 0.17 - % % % % % All Gain Ranges Input Range 5% - 100% VRMS - 0.1 - % 80 -0.25 - VA+ dB V - 500 100 - mVP-P mVP-P NI 80 30 - 94 -115 27 - 22.5 4.5 dB dB pF k Vrms Vrms OD GE - 4.0 0.4 - V/C % All Gain Ranges Input Range 0.1% - 100% Analog Inputs (All Inputs) Common Mode Rejection Common Mode + Signal Analog Inputs (Current Inputs) Differential Input Range [(IIN+) - (IIN-)] Total Harmonic Distortion Crosstalk from Voltage input at Full Scale Input Capacitance Effective Input Impedance Noise (Referred to Input) Offset Drift (Without the High-pass Filter) Gain Error (DC, 50, 60 Hz) CMRR (Gain = 10) (Gain = 50) IIN (Gain = 50) THD (50, 60 Hz) IC EII (Gain = 10) (Gain = 50) (Note 3) Notes: 1. Applies when the HPF option is enabled. 2. Applies when the line frequency is equal to the product of the output word rate (OWR) and the value of Epsilon. DS714F3 7 CS5467 ANALOG CHARACTERISTICS (Continued) Parameter Analog Inputs (Voltage Inputs) Differential Input Range Symbol Min Typ Max Unit [(VIN+) - (VIN-)] VIN - 500 - mVP-P Total Harmonic Distortion Crosstalk from Current inputs at Full Scale (50, 60 Hz) Input Capacitance All Gain Ranges Effective Input Impedance Noise (Referred to Input) THD IC EII NV 65 2 - 75 -70 2.0 - 140 dB dB pF M Vrms Offset Drift (Without the High-pass Filter) Gain Error Temperature Temperature Accuracy Power Supplies Power Supply Currents (Active State) OD GE - 16.0 3.0 - V/C % T - 5 - C PSCA PSCD PSCD - 1.5 3.5 2.3 - mA mA mA PC - 25 15 7 10 33 20 - mW mW mW uW 48 68 60 2.3 - 55 75 65 2.45 2.55 2.7 dB dB dB V V (Note 3) IA+ ID+ (VA+ = VD+ = 5 V) ID+ (VA+ = 5 V, VD+ = 3.3 V) Power Consumption (Note 4) Active State (VA+ = VD+ = 5 V) Active State (VA+ = 5 V, VD+ = 3.3 V) Stand-by State Sleep State Power Supply Rejection Ratio (50, 60 Hz) (Note 5) Voltage Current (Gain = 50x) Current (Gain = 10x) PFMON Low-voltage Trigger Threshold PFMON High-voltage Power-on Trip Point (Note 6) (Note 7) PSRR PMLO PMHI Notes: 3. Applies before system calibration. 4. All outputs unloaded. All inputs CMOS level. 5. Measurement method for PSRR: VREFIN tied to VREFOUT, VA+ = VD+ = 5 V, a 150 mV (zero-to-peak) (60 Hz) sinewave is imposed onto the +5 V DC supply voltage at VA+ and VD+ pins. The "+" and "-" input pins of both input channels are shorted to AGND. The CS5467 is then commanded to continuous conversion acquisition mode, and digital output data is collected for the channel under test. The (zero-to-peak) value of the digital sinusoidal output signal is determined, and this value is converted into the (zero-to-peak) value of the sinusoidal voltage (measured in mV) that would need to be applied at the channel's inputs, in order to cause the same digital sinusoidal output. This voltage is then defined as Veq. PSRR is (in dB): 150 PSRR = 20 log ---------V eq 6. When the voltage level on PFMON is sagging and LSD bit = 0, this is the voltage at which LSD is set to 1. 7. If the LSD bit has been set to 1 (because PFMON voltage fell below PMLO), this is the voltage level on PFMON at which the LSD bit can be permanently reset back to 0. 8 DS714F3 CS5467 VOLTAGE REFERENCE Parameter Symbol Min Typ Max Unit VREFOUT +2.4 +2.5 +2.6 V Reference Output Output Voltage Temperature Coefficient (Note 8) TCVREF - 40 - ppm/C Load Regulation (Note 9) VR - 6 10 mV VREFIN +2.4 +2.5 +2.6 V Input Capacitance - 4 - pF Input CVF Current - 100 - nA Reference Input Input Voltage Range Notes: 8. The voltage at VREFOUT is measured across the temperature range. From these measurements the following formula is used to calculate the VREFOUT temperature coefficient. AVG MIN) ( MAX (T AMAX 1 - TAMIN ( - VREFOUT ( (VREFOUT VREFOUT ( 1.0 x 10 6 ( TCVREF = 9. Specified at maximum recommended output of 1 A, source or sink. DS714F3 9 CS5467 DIGITAL CHARACTERISTICS * * * * Min / Max characteristics and specifications are guaranteed over all Recommended Operating Conditions. Typical characteristics and specifications are measured at nominal supply voltages and TA = 25 C. VA+ = VD+ = 5V 5%; AGND = DGND = 0 V. All voltages with respect to 0 V. DCLK = 4.096 MHz. Parameter Symbol Master Clock Characteristics Master Clock Frequency Internal Gate Oscillator (Note 11) DCLK Master Clock Duty Cycle CPUCLK Duty Cycle (Note 12 and 13) Filter Characteristics Phase Compensation Range (60 Hz, OWR = 4000 Hz) Input Sampling Rate DCLK = MCLK/K Digital Filter Output Word Rate (Both channels) OWR High-pass Filter Corner Frequency -3 dB Full-scale DC Calibration Range (Referred to Input) (Note 14) FSCR Channel-to-channel Time-shift Error (Note 15) Input/Output Characteristics High-level Input Voltage Min Typ Max Unit 2.5 40 40 4.096 - 20 60 60 MHz % % -5.4 25 DCLK/8 DCLK/1024 0.5 1.0 +5.4 100 Hz Hz Hz %FS s 0.6 VD+ (VD+) - 0.5 0.8VD+ - - V V V - - 0.8 1.5 0.2VD+ V V V (VD+) - 1.0 - 0.48 0.3 0.2VD+ - V V V V Iin - 1 0.4 0.4 10 V V A 3-state Leakage Current IOZ - - 10 A Digital Output Pin Capacitance Cout - 5 - pF All Pins Except XIN and SCLK and RESET XIN SCLK and RESET VIH Low-level Input Voltage (VD = 5 V) All Pins Except XIN and SCLK and RESET XIN SCLK and RESET VIL Low-level Input Voltage (VD = 3.3 V) All Pins Except XIN and SCLK and RESET XIN SCLK and RESET High-level Output Voltage VIL Iout = +5 mA VOH Iout = -5 mA (VD = +5V) Iout = -2.5 mA (VD = +3.3V) VOL Low-level Output Voltage Input Leakage Current (Note 16) Notes: 10. All measurements performed under static conditions. 11. If a crystal is used, XIN frequency must remain between 2.5 MHz - 5.0 MHz. If an external oscillator is used, XIN frequency range is 2.5 MHz - 20 MHz, but K must be set so that MCLK is between 2.5 MHz - 5.0 MHz. 12. If external MCLK is used, the duty cycle must be between 45% and 55% to maintain this specification. 13. The frequency of CPUCLK is equal to MCLK. 14. The minimum FSCR is limited by the maximum allowed gain register value. The maximum FSCR is limited by the full-scale signal applied to the input. 15. Configuration register (Config) bits PC[6:0] are set to "0000000". 16. 10 The MODE pin is pulled low by an internal resistor. DS714F3 CS5467 SWITCHING CHARACTERISTICS * * * * Min / Max characteristics and specifications are guaranteed over all Recommended Operating Conditions. Typical characteristics and specifications are measured at nominal supply voltages and TA = 25 C. VA+ = 5 V 5% VD+ = 3.3 V 5% or 5 V 5%; AGND = DGND = 0 V. All voltages with respect to 0 V. Logic Levels: Logic 0 = 0 V, Logic 1 = VD+. Parameter Symbol Min Typ Max Unit trise - 50 1.0 - s ns tfall - 50 1.0 - s ns tost - 60 - ms SCLK - - 2 MHz t1 t2 200 200 - - ns ns CS Falling to SCLK Rising t3 50 - - ns Data Set-up Time Prior to SCLK Rising t4 50 - - ns Data Hold Time After SCLK Rising t5 100 - - ns CS Falling to SDO Driving t6 - 20 50 ns SCLK Falling to New Data Bit (hold time) t7 - 20 50 ns CS Rising to SDO Hi-Z t8 - 20 50 ns Rise Times (Note 17) Any Digital Output Fall Times (Note 17) Any Digital Output Start-up Oscillator Start-up Time XTAL = 4.096 MHz (Note 18) Serial Port Timing Serial Clock Frequency Serial Clock Pulse Width High Pulse Width Low SDI Timing SDO Timing E2PROM mode Timing Serial Clock Pulse Width Low Pulse Width High t9 t10 8 8 DCLK DCLK MODE setup time to RESET Rising t11 50 ns RESET rising to CS falling t12 48 DCLK CS falling to SCLK rising t13 100 SCLK falling to CS rising t14 CS rising to driving MODE low t15 50 ns SDO setup time to SCLK rising t16 100 ns 8 DCLK 16 DCLK Notes: 17. Specified using 10% and 90% points on waveform of interest. Output loaded with 50 pF. 18. Oscillator start-up time varies with crystal parameters. This specification does not apply when using an external clock source. DS714F3 11 CS5467 t3 CS t1 t2 SC LK H ig h B y te LSB MSB MSB-1 LSB MSB-1 LSB C o m m a n d T im e 8 S C L K s MSB MSB t5 MSB-1 LSB SDI MSB-1 MSB t4 M id B y te L o w B y te SDI Write Timing (Not to Scale) CS t1 t8 LSB MSB-1 LSB MSB Low B yte MSB-1 LSB UNKNOW N MSB-1 MSB SDO M id B yte MSB H igh B yte t6 t7 t2 LSB MSB-1 SDI MSB SCLK C om m and T im e 8 S C LK s S Y N C 0 or S Y N C 1 C om m and S Y N C 0 or S Y N C 1 C om m and S Y N C 0 or S Y N C 1 C om m and SDO Read Timing (Not to Scale) t11 t15 MODE ( IN P U T ) RESET ( IN P U T ) CS t14 t12 t7 t13 (O U T P U T ) SCLK (O U T P U T ) t10 t16 t9 t4 SDO t5 STOP bit (O U T P U T ) SDI ( IN P U T ) Last 8 B it s D a ta fro m E E P R O M E2PROM mode Sequence Timing (Not to Scale) Figure 1. CS5467 Read and Write Timing Diagrams 12 DS714F3 CS5467 SWITCHING CHARACTERISTICS (Continued) Parameter Symbol Min Typ Max Unit tperiod 500 - - s Pulse Width tpw 244 - - s Rising Edge to Falling Edge t3 6 - - s E2 Setup to E1 and/or E3 Falling Edge t4 1.5 - - s E1 Falling Edge to E3 Falling Edge t5 248 - - s E1, E2, and E3 Timing (Note 19 and 20) Period Notes: 19. Pulse output timing is specified at DCLK = 4.096 MHz, E2MODE = 0, and E3MODE[1:0] = 0. Refer to 6.7 Energy Pulse Outputs on page 20 for more information on pulse output pins. 20. Timing is proportional to the frequency of DCLK. tperiod tpw E1 t3 t4 E2 t4 E3 tpw t5 tperiod t5 t3 Figure 2. Timing Diagram for E1, E2, and E3 ABSOLUTE MAXIMUM RATINGS WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. Parameter DC Power Supplies Input Current, Any Pin Except Supplies Symbol Min Typ Max Unit (Notes 21 and 22) Positive Digital Positive Analog VD+ VA+ -0.3 -0.3 - +6.0 +6.0 V V (Notes 23, 24, 25) IIN - - 10 mA IOUT - - 100 mA PD - - 500 mW Output Current, Any Pin Except VREFOUT Power Dissipation (Note 26) Analog Input Voltage All Analog Pins VINA - 0.3 - (VA+) + 0.3 V Digital Input Voltage All Digital Pins VIND -0.3 - (VD+) + 0.3 V Ambient Operating Temperature TA -40 - 85 C Storage Temperature Tstg -65 - 150 C Notes: 21. VA+ and AGND must satisfy [(VA+) - (AGND)] + 6.0 V. 22. VD+ and AGND must satisfy [(VD+) - (AGND)] + 6.0 V. 23. Applies to all pins including continuous over-voltage conditions at the analog input pins. 24. Transient current of up to 100 mA will not cause SCR latch-up. 25. Maximum DC input current for a power supply pin is 50 mA. 26. Total power dissipation, including all input currents and output currents. DS714F3 13 CS5467 V1OFF V1GAIN FGA 1 VHPF1 IHPF1 I1OFF I1GAIN Figure 3. Signal Flow for V1, I1, P1, Q1 Measurements 4. SIGNAL PATH DESCRIPTION The data flow for voltage and current measurement and the other calculations are shown in Figures 3, 4, and 5. IIR "anti-sinc" filters, used to compensate for the amplitude roll-off of the decimation filters. 4.1 Analog-to-Digital Converters 4.3 Phase Compensation Voltage1 channel and voltage2/temperature channel use second-order delta-sigma modulators and the two current channels use fourth-order delta-sigma modulators to convert the analog inputs to single-bit digital data streams. The converters sample at a rate of DCLK/8. This high sampling provides a wide dynamic range and simplifies anti-alias filter design. Phase compensation changes the phase of current relative to voltage by changing the sampling time in the decimation filters. The amount of phase shift is set by bits PC[7:0] in the Configuration register (Config) for channel 1 and bits PC[7:0] in the Control register (Ctrl) for channel 2. 4.2 Decimation Filters The single-bit modulator output data is widened to 24 bits and down-sampled to DCLK/1024 with low-pass decimation filters. These decimation filters are third-order Sinc. Their outputs are passed through third-order Phase compensation, PC[7:0] is a signed two's complement binary value in the range of -1.0 to almost +1.0 output word rate (OWR) samples. For a sample rate of 4000 Hz, the delay range is 250 uS, a phase shift of 4.5 at 50 Hz and 5.4 at 60 Hz. The step size would be 0.0352 at 50 Hz and 0.0422 at 60 Hz at this sample rate. V2OFF V2GAIN V2 V2Q FGA Q2 2 VHPF2 IHPF2 P2 2 Control Register I2 I2OFF I2GAIN Figure 4. Signal Flow for V2, I2, P2, Q2 Measurements 14 DS714F3 CS5467 4.4 DC Offset and Gain Correction The system and chip inherently have gain and offset errors which can be removed using the gain and offset registers. (See Section 9. System Calibration on page 40). Each measurement channel has its own registers. For every channel, the output of the IIR filter is added to the offset register and multiplied by the gain register. 4.5 High-pass Filters Optional high-pass filters (HPF in Figures 3 and 4) remove any DC from the selected signal paths. Subsequently, DC will also be removed from power, and all low-rate results. (see Figures 5). Each energy channel has a current and voltage path. If an HPF is enabled in only one path, a phase-matching filter (PMF) is applied to the other path which matches the amplitude and phase delay of the HPF in the band DS714F3 of interest, but passes DC. For more information, see 6.5 High-pass Filters on page 20. The HPF filter multiplexers drive the I1, V1, I2, and V2 result registers. 4.6 Low-Rate Calculations Low-rate results are derived from sample-rate results integrated over N samples, where N is the value stored in the Cycle Count register. The low-rate interval is the sample interval multiplied by N. 4.7 RMS Results The root mean square (RMS in Figure 5) calculations are performed on N instantaneous voltage and current samples, using the formula: N-1 I RMS = I n2 n=0 --------------------N 15 CS5467 V1ACOFF (V2ACOFF) P1 OFF (P2 OFF ) I1 ACOFF (I2 ACOFF) Figure 5. Low-rate Calculations 4.8 Power and Energy Results The instantaneous voltage and current samples are multiplied to obtain the instantaneous power (P1, P2) (see Figure 3 and 4). The product is then averaged over N conversions to compute active power (P1AVG, P2AVG). Q WB = 2 S 2 - P Active Quadrature power (Q1, Q2) are sample rate results obtained by multiplying instantaneous current (I1, I2) by instantaneous quadrature voltage (V1Q, V2Q) which are created by phase shifting instantaneous voltage (V1, V2) 90 degrees using first-order integrators. (See Figure 3 and 4). The gain of these integrators is inversely related to line frequency, so their gain is corrected by the Epsilon register, which is based on line frequency. Apparent power (S1, S2) is the product of RMS voltage and current as shown: S = V RMS I RMS Power factor (PF1, PF2) is active power divided by apparent power as shown below. The sign of the power factor is determined by the active power. Reactive power (Q1Avg, Q2AvG) is generated by integrating the instantaneous quadrature power over N samples. P Active PF = -----------------S Active power (P1AVG, P2AVG), apparent power (S1, S2), and reactive power (Q1AVG, Q2AVG) of the two channels are summed up and then divided by 2. The calculation results are placed in EPULSE, SPULSE, and QPULSE registers which can be configured to drive energy pulse outputs. (See Figure 6.) Wideband reactive power (Q1WB, Q2WB) is calculated by doing a vector subtraction of active power from apparent power. OVF= P1AVG + /2 EPULSE x + EACCM P2AVG OVF= S1 + /2 SPULSE x + SACCM S2 OVF= Q1AVG + /2 QPULSE x + QACCM Q2AVG PulseRate ( E1, E2, E3 ) Figure 6. Two-channel Power Summation 16 DS714F3 CS5467 4.9 Peak Voltage and Current Peak current (I1PEAK, I2PEAK) and peak voltage (V1PEAK, V2PEAK) are the largest current and voltage samples detected in the previous low-rate interval. 4.10 Power Offset The power offset registers, P1OFF (P2OFF) can be used to offset erroneous power sources resident in the system not originating from the power line. Residual power offsets are usually caused by crosstalk into current paths from voltage paths or from ripple on the meter or DS714F3 chip's power supply, or from inductance from a nearby transformer. These offsets can be either positive or negative, indicating crosstalk coupling either in phase or out of phase with the applied voltage input. The power offset registers can compensate for either condition. To use this feature, measure the average power at no load using either Single or Continuous Conversion commands. Take the measured result (from the P1AVG (P2AVG) register), invert (negate) the value and write it to the associated power offset register, P1OFF (P2OFF). 17 CS5467 5. PIN DESCRIPTIONS 5.1 Analog Pins 5.1.6 Crystal Oscillator The CS5467 has four differential inputs: VIN1VIN2 IIN1, and IIN2 are the voltage1, voltage2, current1, and current2 inputs, respectively. A single-ended power fail monitor input, voltage reference input, and voltage reference output are also available. An external quartz crystal can be connected to the XIN and XOUT pins as shown in Figure 7. To reduce system cost, each pin is supplied with an on-chip, phase-shifting capacitor to ground. 5.1.1 Voltage1 & Voltage2 Inputs The output of the line voltage resistive divider or transformer is connected to the VIN1+ (VIN2+) and VIN1(VIN2-) input pins of the CS5467. The voltage channel is equipped with a 10x, fixed-gain amplifier. The full-scale signal level that can be applied to the voltage channel is 250 mV. If the input signal is a sine wave, the maximum RMS voltage is 250 mVp / 2 176.78 mVRMS which is approximately 70.7% of maximum peak voltage. . XOUT C1 Oscillator Circuit XIN C2 DGND C1 = C2 = 22 pF 5.1.2 Current1 & Current2 Inputs The output of the current-sensing resistor or transformer is connected to the IIN1+ (IIN2+) and IIN1- (IIN2-) input pins of the CS5467. To accommodate different current-sensing elements, the current channel incorporates a programmable gain amplifier (PGA) with two selectable input gains. The full-scale signal level for the current channels is 50 mV or 250 mV. If the input signal is a sine wave, the maximum RMS voltage is 35.35 mVRMS or 176.78 mVRMS which is approximately 70.7% of maximum peak voltage. 5.1.3 Power Fail Monitor Input An analog input (PFMON) is provided to determine when a power loss is imminent. By connecting a resistive divider from the unregulated meter power supply to the PFMON input, an interrupt can be generated, or the Low Supply Detected (LSD) Status register bit can be monitored to indicate low-supply conditions. The PFMON input has a comparator that trips around the level of the voltage reference input (VREFIN). 5.1.4 Voltage Reference Input The CS5467 requires a stable voltage reference of 2.5 V applied to the VREFIN pin. This reference can be supplied from an external voltage reference or from the VREFOUT output. A bypass capacitor of at least 0.1 F is recommended at the VREFIN pin. 5.1.5 Voltage Reference Output The CS5467 generates a 2.5 V reference (VREFOUT). It is suitable for driving the VREFIN pin, but has very little fan-out capacity and is not recommended for driving external circuits. 18 Figure 7. Oscillator Connections Alternatively, an external clock source can be connected to the XIN pin. 5.2 Digital Pins 5.2.1 Reset Input The active-low RESET pin, when asserted, will halt all CS5467 operations and reset internal hardware registers and states. When de-asserted, an initialization sequence begins, setting default register values. 5.2.2 CPU Clock Output A logic-level clock output (CPUCLK) is provided at the crystal frequency to drive an external CPU or microcontroller clock. Two phase choices are available. 5.2.3 Interrupt Output The INT pin indicates an enabled Internal Status register (Status) bit is set. Status register bits indicate conditions such as data ready, modulator oscillations, low supply, voltage sag, current faults, numerical overflows, and result updates. 5.2.4 Energy Pulse Outputs The CS5467 provides three pins (E1, E2, E3) for pulse energy outputs. These pins can also be used to output other conditions, such as voltage1 sign, power fail monitor, or energy sign. DS714F3 CS5467 5.2.5 Serial Interface The CS5467 provides 5 pins, SCLK, SDI, SDO, CS, and MODE for communication between a host microcontroller or serial E2PROM and the CS5467. MODE is an input that, when high, indicates to the CS5467 that a serial E2PROM is being used instead of a host microcontroller. It has a weak pull-down allowing it to be left unconnected if microcontroller mode is used. SCLK is used to shift and qualify serial data. Serial data changes as a result of the falling edge of SCLK and is valid during the rising edge. It is a Schmitt-trigger input DS714F3 for host microcontrollers, and a driven output for serial E2PROMs. SDI is the serial data input to the CS5467. SDO is the serial data output from the CS5467. It's output drivers are disabled whenever CS is de-asserted, allowing other devices to drive the SDO line. CS is the chip select input for the serial bus. A high logic level de-asserts it, tri-stating the SDO pin and clearing the serial interface. A low logic level enables the serial port. This pin may be tied low for systems not requiring multiple SDO drivers. CS is a driven output when interfacing to serial E2PROMs. 19 CS5467 6. SETTING UP THE CS5467 6.1 Clock Divider The internal clock to the CS5467 needs to operate around 4 MHz. However, by using the internal clock divider, a higher crystal frequency can be used. This is important when driving an external microcontroller requiring a faster clock and using the CPUCLK output. K is the divide ratio from the crystal input to the internal clock and is selected with Configuration register (Config) bits K[3:0]. It has a range of 1 to 16. A value of zero results in a setting of 16. VHPF IHPF Filter Configuration 0 0 No filter on Voltage or Current 0 1 HPF on Current, PMF on Voltage 1 0 HPF on Voltage, PMF on Current 1 1 HPF on Current and Voltage Table 3. High-pass Filter Configuration 6.2 CPU Clock Inversion By default, CPUCLK is inverted from XIN. Setting Configuration register bit iCPU removes this inversion. This can be useful when one phase adds more noise to the system than the other. 6.3 Interrupt Pin Behavior The behavior of the INT pin is controlled by the IMODE and IINV bits in the Configuration register as shown. IMODE IINV 0 0 Active-low Level 0 1 Active-high Level 1 0 Low Pulse 1 1 High Pulse 6.6 Cycle Count Low-rate calculations, such as average power and RMS voltage and current integrate over several (N) output word rate (OWR) samples. The duration of this averaging window is set by the Cycle Count (N) register. By default, Cycle Count is set to 4000 (1 second at output word rate [OWR] of 4000 Hz). The minimum value for Cycle Count is 10. 6.7 Energy Pulse Outputs INT Pin By default, E1 outputs total active energy, E3, total reactive energy, and E2, the sign of both active and reactive energy. (See Figure 2. Timing Diagram for E1, E2, and E3 on page 13.) Table 1. Interrupt Configuration If IMODE = 1, the duration of the INT pulse will be two DCLK cycles, where DCLK = MCLK/K. 6.4 Current Input Gain Ranges Control register bits I1gain (I2gain) select the input range of the current inputs. Three pairs of bits in the Mode Control (Modes) register control the operation of these outputs. These bits are named E1MODE[1:0], E2MODE[1:0], and E3MODE[1:0]. Some combinations of these bits override others, so read the following paragraphs carefully. The E2 pin can output energy sign, or total apparent energy. Table 4 lists the functions of E2 as controlled by E2MODE[1:0] in the Modes register. Note: E2MODE[1:0]=3 is a special mode. E2MODE1 E2MODE0 E2 output I1gain, I2gain Maximum Input Gain 0 0 Energy Sign 0 250 mV 10x 0 1 Total Apparent Energy 1 50 mV 50x 1 0 Not Used 1 1 Enable E1MODE Table 2. Current Input Gain Ranges 6.5 High-pass Filters Mode Control (Modes) register bits VHPF and IHPF activate the HPF in the voltage and current paths, respectively. Each energy channel has separate VHPF and IHPF bits. When a high-pass filter is enabled in only one 20 path within a channel, a phase matching filter (PMF) is applied to the other path within that channel. The PMF filter matches the amplitude and phase response of the HPF in the band of interest, but passes DC. Table 4. E2 Pin Configuration The E3 pin can output total reactive energy, power fail monitor status, voltage1 sign, or total apparent energy. Table 5 lists the functions of E3 as controlled by DS714F3 CS5467 E3MODE[1:0] in the Modes register when E1MODE is not enabled. E3MODE1 E3MODE0 E3 output 0 0 Total Reactive Energy 0 1 Power Fail Monitor 1 0 Voltage1 Sign 1 1 Total Apparent Energy Table 5. E3 Pin Configuration When both E2MODE bits are high, the E1MODE bits are enabled, allowing active, apparent, reactive, or wide band reactive energy for both energy channels to be output on E1 and E2. Table 6 lists the functions of E1 and E2 with E1MODE enabled. 6.8 No Load Threshold The No Load Threshold register (LoadMIN) is used to zero out the contents of EPULSE and QPULSE registers if their magnitude is less than the LoadMIN register value. 6.9 Energy Pulse Width Note: Energy Pulse Width (PulseWidth) only applies to E1, E2, or E3 pins that are configured to output pulses. When any are configured to output steady-state signals, such as voltage1 sign, power fail monitor, or energy sign, pulse widths and output rates do not apply. The pulse width time (tpw) in Figure 2, is set by the value in the PulseWidth register which is an integer multiple of the sample or output word rate (OWR). At OWR of 4000 Hz (a period of 250 uS) tpw = PulseWidth x 250 uS. By default, PulseWidth is set to 1. 6.10 Energy Pulse Rate E1MODE1 E1MODE0 E1 / E2 outputs 0 0 Active Energy 0 1 Apparent Energy 1 0 Reactive Energy 1 1 Wideband Reactive Table 6. E1 / E2 Modes When E1MODE bits are enabled, the E3 pin outputs either the power fail monitor status, or the sign of the E1 and E2 outputs. Table 7 list the functions of the E3 pin using E3MODE[1:0] in the Modes register when E1MODE is enabled . E3MODE1 E3MODE0 E3 output 0 0 Power Fail Monitor 0 1 Energy Sign 1 0 not used 1 1 not used Table 7. E3 Pin with E1MODE enabled DS714F3 The full-scale pulse frequency of enabled E1, E2, E3 pins is the value in PulseRate x output word rate (OWR)/2. The actual pulse frequency is the full-scale pulse frequency multiplied by the pulse register's (EPULSE, SPULSE, or QPULSE) value. Example: If the output word rate (OWR) is 4000 Hz, and the PulseRate register is set to 0.05, the full-rate pulse frequency is 0.05 x 4000 / 2 = 100 Hz. If the EPULSE register, driving E1, is 0.4567, the pulse output rate on E1 will be 100 Hz x 0.4567 = 45.67 Hz. 6.11 Voltage Sag/Current Fault Detection Voltage sag detection is used to determine when averaged voltage falls below a predetermined level for a specified interval of time. Current fault detection determines when averaged current falls below a predetermined level for a specified interval of time. The specified interval of time (duration) is set by the value in the V1SagDUR (V2SagDUR) and I1FaultDUR (I2FaultDUR) registers. Setting any of these to zero (default) disables the detect feature for the given channel. The value is in output word rate (OWR) samples. The predetermined level is set by the values in the V1SagLEVEL (V2SagLEVEL) and I1FaultLEVEL (I2FaultLEVEL) registers. 21 CS5467 For each enabled input channel, the measured value is rectified and compared to the associated level register. Over the duration window, the number of samples above and below the level are counted. If the number of samples below the level exceeds the number of samples above, a Status register bit V1SAG (V2SAG), I1FAULT (I2FAULT) is set, indicating a sag or fault condition. (see Figure 8).. updated. The Voltage2 register (V2) will not update during the temperature measurement, but resume measurement afterwards. Temperature measurements are stored in the Temperature register (T) which, by default, is configured to a range of 128 degrees on the Celsius (C) scale. The application program can change both the scale and range of Temperature (T) by changing the Temperature Gain (TGAIN) and Temperature Offset (TOFF) registers. Two values must be known -- the transistor's VBE per degree, and the transistor's VBE at 0 degrees. At the time of this publication, these values are: VBE (per degree) = 0.2769523 mV/C or K VBE0 = 79.2604368 mV at 0C To determine the values to write to TGAIN and TOFF, use the following formulae: TGAIN = ADFS / VBE / TFS x 217 TOFF = -VBE0 / ADFS x 223 Figure 8. Sag and Fault Detect 6.12 Epsilon The Epsilon register is used to set the gain of the 90 phase shift used in the quadrature power calculation. The value in the Epsilon register is the ratio of the line frequency to the output word rate (OWR). It is, by default, 50/4000 (0.0125), for 50 Hz line and 4000 Hz sample (OWR) frequencies. In the above equations, ADFS is the full-scale input range of the temperature A/D converter or 833.333 mV and TFS is the desired full-scale range of the Temperature (T) register. The binary exponents are the bit positions of the binary point of these registers. To use the Celsius scale (C) and cover the chip's operating temperature range of -40C to +85C, the Temperature register range needs to be 128 degrees. TFS should be 128 degrees. For 60 Hz line frequency, it is 60/4000 (0.015). Other output word rates (OWR) can be used. TGAIN = 833.333 / 0.2769523 / 128 x 131072 Epsilon can also be calculated automatically by the CS5467 by setting the AFC bit in the Mode Control (Modes) register. The Frequency Update bit (FUP) in the Status register is set every time the Epsilon register has been automatically updated. TOFF = -79.2604368 / 833.333 x 8388608 = -797862 (0xF3D35A) 6.13 Temperature Measurement The on-chip temperature sensor is designed to measure temperature and optionally compensate for temperature drift of the voltage reference. It uses the VBE of a transistor to determine temperature. In the CS5467, voltage2 and temperature are multiplexed on one ADC channel. To initiate a temperature measurement, write 1 to the Temperature Measurement (TMEAS) register. TMEAS will go through counts 1, 2, 4, and back to 0. Wait for TMEAS to return to 0. When done, Temperature (T) is updated. The Status register bit TUP also indicates when the Temperature register is 22 = 3081155 (0x2F03C3) These are the actual default values for these registers. TGAIN and TOFF can also be used to calibrate the gain and/or offset of the temperature sensor or A/D converter. (See Section 9. System Calibration on page 40). To use the Kelvin (K) scale, simply add 273 times VBE / ADFS x 223 to TOFF since 0C = 273K,. You will also need more range. Since -40C to +85C is 233K to 358K, a TFS of 512 degrees should be used in the TGAIN calculation. To use the Fahrenheit (F) scale, multiply VBE by 5/9 and add 32 times the newVBE / ADFS x 223 to TOFF since 0C = 32F. You will also want to use aTFS of 256 degrees to cover the -40C to +85C range. DS714F3 CS5467 7. USING THE CS5467 7.1 Initialization The CS5467 uses a power-on-reset circuit (POR) to provide an internal reset until the analog voltage reaches 4.0 V. The RESET input pin can also be used by the application circuit to reset the part. After RESET is removed and the oscillator is stable, an initialization program is executed to set the default register values. A Software Reset command is also provided to allow the application to run the initialization program without removing power or asserting RESET. to entering the stand-by state. When returning from sleep mode, a complete initialization occurs. 7.3 Voltage Tamper Correction The CSS5467 provides compensation for meter tampering on voltage channels. If the application detects that the voltage input has been impaired it may choose to use the fixed internal RMS voltage reference by setting the VFIX bit in the Modes register. The value of this reference (VFRMS) is by default 0.707107 (full-scale RMS) but can be changed by the application program. (See figure 9) The application should avoid sending commands during initialization. The DRDY bit in the Status register indicates when the initialization program has completed. 7.2 Power-down States The CS5467 has two power-down states, stand-by and sleep. In the stand-by state, all circuitry except the voltage reference and crystal oscillator is powered off. In sleep state, all circuitry except the instruction decoder is powered off. To return the device to the active state, send a Wakeup/Halt command to the device. When returning from stand-by mode, registers will retain their contents prior DS714F3 Figure 9. Fixed RMS Voltage Selection 23 CS5467 7.4 Command Interface Commands and data are transferred most-significant bit (MSB) first. Figure 1 on page 12, defines the serial port timing. Commands are clocked in on SDI using SCLK. They are a single byte (8 bits) long and fall into one of four basic types: 1. Register Read 2. Register Write 3. Synchronizing 4. Instructions Register reads will cause up to four bytes of register data to be clocked out, MSB first on the SDO pin by SCLK. During this time, other commands can be clocked in on the SDI pin. Other commands will not interrupt read data, except another register read, which will cause the new read data to appear on SDO. Synchronizing can be sent while read data is being clocked out if no other commands need to be sent. 24 Synchronizing commands are also used to synchronize the serial port to a byte boundary. The CS and RESET pins will also synchronize the serial port. Register writes require three bytes of write data to follow, clocked in on the SDI pin, MSB first by SCLK. Instructions are commands that will interrupt any instruction currently executing and begin the new instruction. These include conversions, calibrations, power control, and soft reset. (See Section 7.6 Commands on page 25). 7.5 Register Paging Read and Write commands access one of 32 registers within a specified page. The Register Page Select register's (Page) default value is 0. To access registers in another page, write the desired page number to the Page register. The Page register is always at address 31 and is accessible from within any page. DS714F3 CS5467 7.6 Commands All commands are 1 byte (8 bits) long. Many command values are unused and should NOT be written by the application program. All commands except register reads, register writes, or synchronizing commands will abort any conversion, calibration, or any initialization sequence currently executing. This includes reset. No commands other than reads or synchronizing should be executed until the reset sequence completes. 7.6.1 Conversion B7 1 B6 1 B5 1 B4 0 B3 CC B2 0 B1 0 B0 0 Executes a conversion (measurement) program. CC Continuous/Single Conversion 0 = Perform a Single Conversion (0xE0) 1 = Perform Continuous Conversion (0xE8) 7.6.2 Synchronization (SYNC0 and SYNC1) B7 1 B6 1 B5 1 B4 1 B3 1 B2 1 B1 1 B0 SYNC The serial interface is bidirectional. While reading data on the SDO output, the SDI input must be receiving commands. If no command is needed during a read, SYNC0 or SYNC1 commands can be sent while read data is received on SDO. The serial port is normally initialized by de-asserting CS. An alternative method of initialization is to send 3 or more SYNC1 commands followed by a SYNC0. This is useful in systems where CS is not used and tied low. 7.6.3 Power Control (Stand-by, Sleep, Wake-up/Halt and Software Reset) B7 1 B6 0 B5 S1 B4 S0 B3 0 B2 0 B1 0 B0 0 The CS5467 has two power-down states, stand-by and sleep. In stand-by, all circuitry except the voltage reference and clocks are turned off. In sleep mode, all circuitry except the command decoder is turned off. A Wake-up/Halt command restores full-power operation after stand-by and issues a hardware reset after sleep. The Software Reset command is a program that emulates a pin reset and is not a power control function. S[1:0] DS714F3 00 = Software Reset 01 = Sleep 10 = Wake-up/Halt 11 = Stand-by 25 CS5467 7.6.4 Calibration B7 1 B6 0 B5 CAL5 B4 CAL4 B3 CAL3 B2 CAL2 B1 CAL1 B0 CAL0 The CS5467 can perform gain and offset calibrations using either DC or AC signals. Proper input levels must be applied to the current inputs and voltage input before performing calibrations. 26 CAL[5:4]* 00 = DC Offset 01 = DC Gain 10 = AC Offset 11 = AC Gain CAL[3:0] 0001 = Current for Channel 1 0010 = Voltage for Channel 1 0100 = Current for Channel 2 1000 = Voltage for Channel 2 Note: Anywhere from 1 to all 4 channels can be calibrated simultaneously. DS714F3 CS5467 7.6.5 Register Read and Write B7 0 B6 W/R B5 RA4 B4 RA3 B3 RA2 B2 RA1 B1 RA0 B0 0 Read and Write commands provide access to on-chip registers. After a Read command, the addressed data can be clocked out the SDO pin by SCLK. After a Write command, 24 bits of write data must follow. The data is transferred to the addressed register after the 24th data bit is received. Registers are organized into pages of 32 addresses each. To access a desired page, write its number to the Page register at address 31. W/R Write/Read control 0 = Read 1 = Write RA[4:0] Register address. Page 0 Registers Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 R 31 W RA[4:0] 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 11111 Name Config I1 V1 P1 P1AVG I1RMS V1RMS I2 V2 P2 P2AVG I2RMS V2RMS Q1AVG Q1 Status Q2AVG Q2 I1PEAK V1PEAK S1 PF1 I2PEAK V2PEAK S2 PF2 Mask T Ctrl EPULSE SPULSE QPULSE Page Description Configuration Instantaneous Current Channel 1 Instantaneous Voltage Channel 1 Instantaneous Power Channel 1 Active Power Channel 1 RMS Current Channel 1 RMS Voltage Channel 1 Instantaneous Current Channel 2 Instantaneous Voltage Channel 2 Instantaneous Power Channel 2 Active Power Channel 2 RMS Current Channel 2 RMS Voltage Channel 2 Reactive Power Channel 1 Instantaneous Quadrature Power Channel 1 Internal Status Reactive Power Channel 2 Instantaneous Quadrature Power Channel 2 Peak Current Channel 1 Peak Voltage Channel 1 Apparent Power Channel 1 Power Factor Channel 1 Peak Current Channel 2 Peak Voltage Channel 2 Apparent Power Channel 2 Power Factor Channel 2 Interrupt Mask Temperature Control Active Energy Pulse Output Apparent Energy Pulse Output Reactive Energy Pulse Output Register Page Select Warning: Do not write to unpublished register locations. DS714F3 27 CS5467 Page1 Registers Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 25 26 27 28 29 31 W RA[4:0] 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10011 10100 10101 10110 10111 11001 11010 11011 11100 11101 11111 Name I1OFF I1GAIN V1OFF V1GAIN P1OFF I1ACOFF V1ACOFF I2OFF I2GAIN V2OFF V2GAIN P2OFF I2ACOFF V2ACOFF PulseWidth PulseRate Modes Epsilon N Q1WB Q2WB TGAIN TOFF TSETTLE LoadMIN VFRMS G Time Page Description Current DC Offset Channel 1 Current Gain Channel 1 Voltage DC Offset Channel 1 Voltage Gain Channel 1 Power Offset Channel 1 Current AC (RMS) Offset Channel 1 Voltage AC (RMS) Offset Channel 1 Current DC Offset Channel 2 Current Gain Channel 2 Voltage DC Offset Channel 2 Voltage Gain Channel 2 Power Offset Channel 2 Current AC (RMS) Offset Channel 2 Voltage AC (RMS) Offset Channel 2 Pulse Output Width Pulse Output Rate (frequency) Mode Control Ratio of Line to Sample Frequency Cycle Count (Number of OWR Samples in One Low-rate Interval) Wideband Reactive Power from Power Triangle Channel 1 Wideband Reactive Power from Power Triangle Channel 2 Temperature Sensor Gain Temperature Sensor Offset Filter Settling Time for Conversion Startup No Load Threshold Voltage RMS Fixed Reference System Gain System Time (in samples) Register Page Select RA[4:0] 00000 00001 00100 00101 01000 01001 01100 01101 11111 Name V1SagDUR V1SagLEVEL I1FaultDUR I1FaultLEVEL V2SagDUR V2SagLEVEL I2FaultDUR I2FaultLEVEL Page Description V Sag Duration Channel 1 V Sag Level Channel 1 I Fault Duration Channel 1 I Fault Level Channel 1 V Sag Duration Channel 2 V Sag Level Channel 2 I Fault Duration Channel 2 I Fault Level Channel 2 Register Page Select RA[4:0] 11010 11111 Name TMEAS Page Description Temperature Measurement Register Page Select Page2 Registers Address 0 1 4 5 8 9 12 13 31 W Page5 Register Address 26 31 W Warning: Do not write to unpublished register locations. 28 DS714F3 CS5467 8. REGISTER DESCRIPTIONS 1. "Default" = bit states after power-on or reset 2. DO NOT write a "1" to any unpublished register bit. 3. DO NOT write to any unpublished register address. 8.1 Page Register 8.1.1 Page - Address: 31, Write-only, can be written from ANY page. MSB LSB 26 2 5 2 4 2 3 2 2 1 2 20 Default = 0 Register Read and Write commands contain only 5 address bits. But the internal address bus of the CS5467 is 12 bits wide. Therefore, registers are organized into "Pages". There are 128 pages of 32 registers each. The Page register provides the 7 high-order address bits and selects one of the 128 register pages. Not all pages are used, Page is a write-only integer containing 7 bits. 8.2 Page 0 Registers 8.2.1 Configuration (Config) - Address: 0 23 PC7 22 PC6 21 PC5 20 PC4 19 PC3 18 PC2 17 PC1 16 PC0 15 EWA 14 - 13 - 12 IMODE 11 IINV 10 - 9 - 8 - 7 - 6 - 5 - 4 iCPU 3 K3 2 K2 1 K1 0 K0 Default = 1 (K=1) PC[7:0] Phase compensation for channel 1. Sets a delay in voltage, relative to current. Phase is signed and in the range of -1.0 value 1.0 sample (OWR) intervals. EWA Allows the E1 and E2 pins to be configured as open-drain outputs. 0 = Normal Outputs 1 = Open-drain Outputs IMODE, IINV Interrupt configuration. Selects INT pin behavior. 00 = Low Logic Level When Asserted 01 = High Logic Level When Asserted 10 = Low-going Pulse on New Interrupt 11 = High-going Pulse on New Interrupt iCPU Inverts the CPUCLK output. 0 = Default 1 = Invert CPUCLK. K[3:0] Clock divider. Divides MCLK by K to generate internal clock DCLK. (DCLK = MCLK/K). K is unsigned and in the range of 1 to 16. When zero, K = 16. At reset, K = 1. DS714F3 29 CS5467 8.2.2 Instantaneous Current (I1, I2), Voltage (V1, V2), and Power (P1, P2) Address: 1 (I1), 2 (V1), 3 (P2), 7 (I2), 8 (V2), 9 (P2) MSB 0 -(2 ) LSB 2 -1 2 -2 -3 2 -4 2 -5 2 -6 2 -7 2 ..... 2-17 2 -18 2 -19 2 -20 2 -21 2 -22 2-23 I1 (I2) and V1 (V2) contain instantaneous current and voltage, respectively, which are multiplied to yield instantaneous power, P1 (P2). These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.2.3 Active Power (P1AVG , P2AVG ) Address: 4 (P1AVG ), 10 (P2AVG ) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Instantaneous power is averaged over each low-rate interval (N samples) to compute active power, P1AVG (P2AVG). These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.2.4 RMS Current (I1RMS , I2RMS ) and Voltage (V1RMS , V2RMS ) Address: 5 (I1RMS), 6 (V1RMS), 11 (I2RMS), 12 (V2RMS) MSB 2-1 LSB 2-2 2-3 2-4 2-5 2-6 2-7 2-8 ..... 2-18 2-19 2-20 2-21 2-22 2-23 2-24 I1RMS (I2RMS) and V1RMS (V2RMS) contain the root mean square (RMS) values of I1 (I2) and V1 (V2), calculated each low-rate interval. These are unsigned values in the range of 0 value 1.0, with the binary point to the left of the MSB. 8.2.5 Instantaneous Quadrature Power (Q1, Q2) Address: 14 (Q1), 17 (Q2) MSB -(2 0) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Instantaneous quadrature power, Q1 (Q2), the product of voltage1 (voltage2) shifted 90 degrees and current1 (current2). These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.2.6 Reactive Power (Q1Avg , Q2AVG ) Address: 13 (Q1AVG), 16 (Q2AVG) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Reactive power Q1AVG (Q2AVG) is Q1 (Q2) averaged over every N samples. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 30 DS714F3 CS5467 8.2.7 Peak Current (I1PEAK, I2PEAK ) and Peak Voltage (V1PEAK, V2PEAK ) Address: 18 (I1PEAK), 19 (V1PEAK), 22 (I2PEAK), 23 (V2PEAK) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Peak current, I1PEAK (I2PEAK) and peak voltage, V1PEAK (V2PEAK) are the instantaneous current and voltage samples with the greatest magnitude detected during the last low-rate interval. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.2.8 Apparent Power (S1, S2) Address: 20 (S1), 24 (S2) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Apparent power S1 (S2) is the product of V1RMS and I1RMS (V2RMS and I2RMS), These are two's complement values in the range of 0 value 1.0, with the binary point to the right of the MSB. 8.2.9 Power Factor (PF1, PF2) Address: 21 (PF1), 25 (PF2) MSB -(20) 2-1 LSB 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Power factor is calculated by dividing active power by apparent power. The sign is determined by the active power sign. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.2.10 Temperature (T) - Address: 27 MSB LSB -(27) 26 25 24 23 22 21 20 ..... 2-10 2-11 2-12 2-13 2-14 2-15 2-16 T contains results from the on-chip temperature measurement. By default, T uses the Celsius scale, and is a two's complement value in the range of -128.0 value 128.0 (oC), with the binary point to the right of bit 16. T can be rescaled by the application using the TGAIN and TOFF registers. 8.2.11 Active, Apparent, and Reactive Energy Pulse Outputs (EPULSE , SPULSE , QPULSE ) Address: 29 (EPULSE), 30 (SPULSE), 31 (QPULSE) MSB -(20 ) LSB 2 -1 2 -2 -3 2 -4 2 -5 2 -6 2 -7 2 ..... 2-17 2 -18 2 -19 2 -20 2 -21 2 -22 2-23 These drive the pulse outputs when configured to do so. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. Refer to 4.8 Power and Energy Results on page 16. DS714F3 31 CS5467 8.2.12 Internal Status (Status) and Interrupt Mask (Mask) Address: 15 (Status); 26 (Mask) 23 DRDY 22 I2OR 21 V2OR 20 CRDY 19 I2ROR 18 V2ROR 17 I1OR 16 V1OR 15 E2OR 14 I1ROR 13 V1ROR 12 E1OR 11 I1FAULT 10 V1SAG 9 I2FAULT 8 V2SAG 7 TUP 6 V2OD 5 I2OD 4 V1OD 3 I1OD 2 LSD 1 FUP 0 IC Default = 1 (Status), 0 (Mask) The Status register indicates a variety of conditions within the chip. Writing a '1' to a Status register bit will clear that bit if the condition that set it has been removed. Writing a '0' to any bit has no effect. The Mask register is used to control the activation of the INT pin. Writing a '1' to a Mask register bit will allow the corresponding Status register bit to activate the INT pin when set. DRDY Data Ready. During conversion, this bit indicates that low-rate results have been updated. It indicates completion of other commands and the reset sequence. I1OR (I2OR) Current Out of Range. Set when the measured current would cause the I1 (I2) register to overflow. V1OR (V2OR) Voltage Out of Range. Set when the measured voltage would cause the V1 (V2) register to overflow. CRDY Conversion Ready. Indicates that sample rate (output word rate) results have been updated. I1ROR (I2ROR) RMS Current Out of Range. Set when RMS current would cause the I1RMS (I2RMS) register to overflow. V1ROR (V2ROR) RMS Voltage Out of Range. Set when RMS voltage would cause the V1RMS (V2RMS) register to overflow. E1OR (E2OR) Energy Out of Range. Set when average power would cause P1AVG (P2AVG) to overflow. I1FAULT (I2FAULT)Indicates when a current fault condition has occurred. 32 V1SAG (V2SAG) Indicates when a voltage sag condition has occurred. TUP Indicates when the Temperature register (T) has been updated. V1OD (V2OD) Modulator oscillation has been detected in the voltage1 (voltage2) A/D. I1OD (I2OD) Modulator oscillation has been detected in the current1 (current2) A/D. LSD Low Supply Detect. Set when the voltage on the PFMON pin falls below the specified low level. The LSD bit cannot be reset until the voltage rises above the specified high level. FUP Frequency Updated. Indicates the Epsilon register has been updated. IC Invalid Command. Normally logic 1. Set to 0 when an invalid command is received. It may also indicate loss of serial command synchronization and the part may need to be re-initialized. DS714F3 CS5467 8.2.13 Control (Ctrl) - Address: 28 23 PC7 22 PC6 21 PC5 20 PC4 19 PC3 18 PC2 17 PC1 16 PC0 15 - 14 - 13 - 12 I2gain 11 - 10 - 9 - 8 STOP 7 - 6 - 5 I1gain 4 INTOD 3 - 2 NOCPU 1 NOOSC 0 - Default = 0 PC[7:0] Phase compensation for channel 2. Sets a delay in voltage relative to current. Phase is signed and in the range of -1.0 value 1.0 sample (OWR) intervals. I1gain (I2gain) Sets the gain of the current1 (current2) input. 0 = Gain is set for 250mV range. 1 = Gain is set for 50mV range. STOP Terminates E2PROM command sequence (if used). 0 = No Action 1 = Stop E2PROM Commands. INTOD Converts INT output pin to an open drain output. 0 = Normal Output 1 = Open-drain Output NOCPU Saves power by disabling the CPUCLK output pin. 0 = CPUCLK Enabled 1 = CPUCLK Disabled NOOSC Disables the crystal oscillator, making XIN a logic-level input. 0 = Crystal Oscillator Enabled 1 = Crystal Oscillator Disabled DS714F3 33 CS5467 8.3 Page 1 Registers 8.3.1 DC Offset for Current (I1OFF , I2OFF ) and Voltage (V1OFF , V2OFF ) Address: 0 (I1OFF ), 2 (V1OFF ), 7 (I2OFF ), 9 (V2OFF ) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0 DC offset registers I1OFF & V1OFF (I2OFF & V2OFF ) are initialized to zero on reset. During DC offset calibration, selected registers are written with the inverse of the DC offset measured. The application program can also write the DC offset register values. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.3.2 Gain for Current (I1GAIN , I2GAIN ) and Voltage (V1GAIN , V2GAIN ) Address: 1 (I1GAIN ), 3 (V1GAIN ), 8 (I2GAIN ), 10 (V2GAIN ) MSB 21 LSB 20 2-1 2-2 2-3 2-4 2-5 2-6 ..... 2-16 2-17 2-18 2-19 2-20 2-21 2-22 Default = 1.0 Gain registers I1GAIN & V1GAIN (I2GAIN & V2GAIN) are initialized to 1.0 on reset. During AC or DC gain calibration, selected register are written with the multiplicative inverse of the gain measured. These are unsigned fixed-point values in the range of 0 value 4.0, with the binary point to the right of the second MSB. 8.3.3 Power Offset (P1OFF , P2OFF ) Address: 4 (P1OFF ), 11 (P2OFF ) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0 Power offset P1OFF (P2OFF ) is added to instantaneous power and averaged over a low-rate interval to yield P1AVG (P2AVG ) register results. It can be used to reduce systematic energy errors. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 8.3.4 AC Offset for Current (I1ACOFF , I2ACOFF ) and Voltage (V1ACOFF , V2ACOFF ) Address: 5 (I1ACOFF ), 6 (V1ACOFF ), 12 (I2ACOFF ), 13 (V2ACOFF ) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0 AC offset registers I1ACOFF & V1ACOFF (VACOFF & V2ACOFF ) are initialized to zero on reset. These are added to the RMS results before being stored to the RMS result registers. They can be used to reduce systematic errors in the RMS results. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. 34 DS714F3 CS5467 8.3.5 Mode Control (Modes) - Address: 16 23 - 22 VFIX 21 - 20 - 19 - 18 - 17 - 16 - 15 - 14 E1MODE1 13 E1MODE0 12 - 11 - 10 E2MODE1 9 E2MODE0 8 VHPF2 7 6 5 4 3 2 1 0 IHPF2 VHPF1 IHPF1 - E3MODE1 E3MODE0 POS AFC Default = 0 VFIX Use internal RMS voltage reference instead of voltage input for average active power. 0 = Use voltage input. 1 = Use internal RMS voltage reference, VFRMS. E1MODE[1:0] E1, E2, and E3 alternate output mode (when enabled by E2MODE). 00 = E1, E2 = P1AVG, P2AVG 01 = E1, E2 = S1, S2 10 = E1, E2 = Q1AVG, Q2AVG 11 = E1, E2 = Q1WB, Q2WB E2MODE[1:0] E2 Output Mode 00 = Energy Sign 01 = Total Apparent Energy 10 = Not Used 11 = Enable E1MODE VHPF2:IHPF2 High-pass Filter Enable for Energy Channel 2 00 = No Filter 01 = HPF on Current, PMF on Voltage 10 = HPF on Voltage, PMF on Current 11 = HPF on both Voltage and Current VHPF1:IHPF1 High-pass Filter Enable for Energy Channel 1 00 = No Filter 01 = HPF on Current, PMF on Voltage 10 = HPF on Voltage, PMF on Current 11 = HPF on both Voltage and Current E3MODE[1:0] E3 Output Mode (with E1MODE disabled) 00 = Total Reactive Energy (default) 01 = Power Fail Monitor 10 = Voltage1 Sign 11 = Total Apparent Energy E3MODE[1:0] E3 Output Mode (with E1MODE enabled) 00 = Power Fail Monitor 01 = Energy Sign 10 = Not Used 11 = Not Used POS Positive Energy Only. Suppresses negative values in P1AVG and P2AVG. If a negative value is calculated, zero will be stored instead. AFC Enables automatic line frequency measurement which sets Epsilon every time a new line frequency measurement completes. Epsilon is used to control the gain of the 90 degree phase shift integrator used in quadrature power calculations. DS714F3 35 CS5467 8.3.6 Line to Sample Frequency Ratio (Epsilon) - Address: 17 MSB 0 -(2 ) LSB 2 -1 2 -2 -3 2 -4 2 -5 2 -6 2 -7 2 ..... 2-17 2 -18 2 -19 2 -20 2 -21 2 -22 2-23 Default = 0.0125 (4.0 kHz x 0.0125 or 50 Hz) Epsilon is the ratio of the input line frequency to the output word rate (OWR). It can either be written by the application program or calculated automatically from the line frequency (from the voltage input) using the AFC bit in the Modes register. It is a two's complement value in the range of -1.0 value 1.0, with the binary point to the right of the MSB. Negative values are not used. 8.3.7 Pulse Output Width (PulseWidth) - Address: 14 MSB 0 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 1 (250 uS at OWR = 4 kHz) PulseWidth sets the duration of energy pulses. The actual pulse duration is the contents of PulseWidth divided by the output word rate (OWR). PulseWidth is an integer in the range of 1 to 8,388,607. 8.3.8 Pulse Output Rate (PulseRate) - Address: 15 MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default= -1 PulseRate sets the full-scale frequency for E1, E2, E3 pulse outputs. For a 4 kHz sample rate, the maximum pulse rate is 2 kHz. This is a two's complement value in the range of -1 value 1, with the binary point to the left of the MSB. Refer to 6.10 Energy Pulse Rate on page 21 for more information. 8.3.9 Cycle Count (N) - Address: 19 MSB 0 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 4000 Determines the number of output word rate (OWR) samples to use in calculating low-rate results. Cycle Count (N) is an integer in the range of 10 to 8,388,607. Values less than 10 should not be used. 8.3.10 Wideband Reactive Power (Q1WB , Q2WB ) Address: 20 (Q1WB ), 21 (Q2WB ) MSB -(2 0) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Wideband reactive power is calculated using vector subtraction. (See Section 4.8 Power and Energy Results on page 16). The value is signed, but has a range of 0 value 1.0. The binary point is to the right of the MSB. 36 DS714F3 CS5467 8.3.11 Temperature Gain (TGAIN ) - Address: 22 MSB 2 LSB 6 2 5 2 4 2 3 2 2 1 2 0 2 -1 2 ..... 2-11 2 -12 2 -13 2 -14 2 -20 2 -15 2 -21 2 -16 2 -22 2-17 Default = 0x2F02C3 Refer to 6.13 Temperature Measurement on page 22 for more information. 8.3.12 Temperature Offset (TOFF ) - Address: 23 MSB -(20 ) LSB 2 -1 2 -2 -3 2 -4 2 -5 2 -6 2 -7 2 ..... 2-17 2 -18 2 -19 2-23 Default = 0xF3D35A Refer to 6.13 Temperature Measurement on page 22 for more information. 8.3.13 Filter Settling Time for Conversion Startup (TSETTLE ) - Address: 25 MSB 223 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 30 Sets the number of output word rate (OWR) samples that will be used to allow filters to settle at the beginning of Conversion and Calibration commands. This is an integer in the range of 0 to 8,388,607 samples. 8.3.14 No Load Threshold (LoadMIN ) - Address: 26 MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0 LoadMIN is used to set the no load threshold. When the magnitude of the EPULSE register is less than LoadMIN, EPULSE will be zeroed. If the magnitude of the QPULSE register is less than LoadMIN, Qpulse will be zeroed. LoadMIN is a two's compliment value in the range of -1.0 value 1.0, with the binary point to the right of the MSB. Negative values are not used. 8.3.15 Voltage Fixed RMS Reference (VFRMS ) - Address 27 MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0.7071068 (full scale RMS) If the application program detects that the meter has possibly been tampered with in such a manner that the voltage input is no longer working, it may choose to use this internal RMS reference instead of the disabled voltage input by setting the VFIX bit in the Modes register. This is a two's complement value in the range of 0 value 1.0, with the binary point to the right of the MSB. Negative values are not used. DS714F3 37 CS5467 8.3.16 System Gain (G) - Address: 28 MSB 1 -(2 ) LSB 2 0 2 -1 -2 2 -3 2 -4 2 -5 2 -6 2 ..... 2-16 2 -17 2 -18 2 -19 2 -20 2 -21 2-22 Default = 1.25 System Gain (G) is applied to all channels. By default, G = 1.25, but can be finely adjusted to compensate for voltage reference error. It is a two's complement value in the range of -2.0 value 2.0, with the binary point to the right of the second MSB. Values should be kept within 5% of 1.25. 8.3.17 System Time (Time) - Address: 29 MSB 223 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 0 System Time (Time) is measured in output word rate (OWR) samples. This is an unsigned integer in the range of 0 to 16,777,215 samples. At OWR = 4.0 kHz, OWR will overflow every 1 hour, 9 minutes, and 54 seconds. Time can be used by the application to manage real-time events. 38 DS714F3 CS5467 8.4 Page 2 Registers 8.4.1 Voltage Sag and Current Fault Duration (V1SagDUR , V2SagDUR , I1FaultDUR , I2FaultDUR ) Address: 0 (V1SagDUR ), 8 (V2SagDUR ), 4 (I1FaultDUR ), 12 (I2FaultDUR ) MSB 0 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 0 Voltage sag duration, V1SagDUR (V2SagDUR) and current fault duration, I1FaultDUR (I2FaultDUR) determine the count of output word rate (OWR) samples utilized to determine a sag or fault event. These are integers in the range of 0 to 8,388,607 samples. A value of zero disables the feature. 8.4.2 Voltage Sag and Current Fault Level (V1SagLEVEL , V2SagLEVEL , I1FaultLEVEL , I2FaultLEVEL ) Address: 1 (V1SagLEVEL ), 9 (V2SagLEVEL ), 5 (I1FaultLEVEL ), 13 (I2FaultLEVEL ) MSB -(20) LSB 2-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23 Default = 0 Voltage sag level, V1SagLEVEL (V2SagLEVEL ) and current fault level, I1FaultLEVEL (I2FaultLEVEL ) establish an input level below which a sag or fault is triggered. These are two's complement values in the range of -1.0 value 1.0, with the binary point to the right of the MSB. Negative values are not used. 8.5 Page 5 Register 8.5.1 Temperature Measurement (TMEAS ) - Address: 26 MSB 223 LSB 222 221 220 219 218 217 216 ..... 26 25 24 23 22 21 20 Default = 0 The Temperature Measurement (TMEAS) register is used to cycle-steal voltage channel2 for temperature measurement. Writing a one to the LSB causes the temperature to be measured and the Temperature register (T) to be updated. Refer to 6.13 Temperature Measurement on page 22 for more information. DS714F3 39 CS5467 9. SYSTEM CALIBRATION 9.1 Calibration The CS5467 provides DC offset and gain calibration that can be applied to the voltage and current measurements, and AC offset calibration which can be applied to the voltage and current RMS calculations. External Connections + + AIN+ 0V +- Since the voltage and current channels have independent offset and gain registers, offset and gain calibration can be performed on any channel independently. XGAIN - CM +- AIN- The data flow of the calibration is shown in Figure 10. The CS5467 must be operating in its active state and ready to accept valid commands. Refer to 7.6 Commands on page 25. The value in the Cycle Count register (N) determines the number of output word rate (OWR) samples that are averaged during a calibration. DC offset and gain calibrations take at least N + TSETTLE samples. AC offset calibrations take at least 6(N) + TSETTLE samples. As N is increased, the accuracy of calibration results tends to also increase. The DRDY bit in the Status register will be set at the completion of Calibration commands. If an overflow occurs during calibration, other Status register bits may be set as well. 9.1.1 Offset Calibration During offset calibrations, no line voltage or current should be applied to the meter. A zero-volt differential signal can also be applied to the voltage inputs VIN1 VIN2 or current inputs IIN1 (IIN2 of the CS5467. (see Figure 11.) Figure 11. System Calibration of Offset 9.1.1.1 DC Offset Calibration The DC Offset Calibration command measures and averages DC values read on specified voltage or current channels at zero input and stores the inverse result in the associated offset registers. This will be added to instantaneous measurements in subsequent conversions, removing the offset. Gain registers for channels being calibrated should be set to 1.0 prior to performing DC offset calibration. 9.1.1.2 AC Offset Calibration The AC Offset Calibration command measures the residual RMS values read on specified voltage or current channels at zero input and stores the inverse result in the associated AC offset registers. This will be added to RMS measurements in subsequent conversions, removing the offset. AC offset registers for channels being calibrated should first be cleared prior to performing the calibration. V1, I1, V2, I2 In Modulator Filter N + X X I1DCOFF, V1DCOFF, I1GAIN, V1GAIN, I2DCOFF, V2DCOFF I2GAIN, V2GAIN DC Offset AC Gain N + + + RMS I1RMS, V1RMS, I2RMS, V2RMS I1ACOFF, V1ACOFF, I2ACOFF, V2ACOFF N AC Offset DC Gain 1 DCAVG N Negate DC AVG Negate 0.6 RMS = READABLE/WRITABLE REGISTERS. Figure 10. Calibration Data Flow 40 DS714F3 CS5467 9.1.2 Gain Calibration During gain calibration, a full-scale reference signal must be applied to the meter or optionally, scaled to the VIN1VIN2,IIN1 (IIN2pins of the CS5467. A DC reference must be used for DC gain calibration. Either an AC or DC reference can be used for RMS AC calibrations. If DC is used, the associated high-pass filter (HPF) must be off. Figure 12 shows the basic setup for gain calibration. External Connections R eference + Signal - IN+ + + CM + - IN- - Figure 12. System Calibration of Gain. Using a reference that is too large or too small can cause an over-range condition during calibration. Either condition can set Status register bits I1OR (I2OR) V1OR (V2OR) for DC and I1ROR (I2ROR) V1ROR (V2ROR) for AC calibration. Full scale (FS) for the voltage input is 250 mV peak and for the current inputs is 250 mV or 50 mV peak depending on selected gain range. The normal peak voltage applied to these pins should not exceed these levels during calibration or normal operation. The range of the gain registers limits the gain calibration range and subsequently the range of the reference level that can be applied. The reference should not exceed FS or be lower than FS/4. 9.1.2.1 AC Gain Calibration Full scale for AC RMS gain calibrations is 60% of the input's full-scale range, which is either 250 mV or 50 mV depending on the gain range selected. That's 150 mV or 30 mV, again depending on range. So the normal reference input level should be either 150 or 30 mVRMS, AC or DC. Prior to executing an AC Gain Calibration command, gain registers for any channel to be calibrated should be set to 1.0 if the reference level mentioned above is used, or to that level divided by the actual reference level used. DS714F3 9.1.2.2 DC Gain Calibration With a DC reference applied, the DC Gain Calibration command measures and averages DC values read on the specified voltage or current channels and stores the reciprocal result in the associated gain registers, converting measured voltage into needed gain. Subsequent conversions will use the new gain value. 9.1.3 Calibration Order 1. DC offset. XG AIN - During AC gain calibration the RMS level of the applied reference is measured with the preset gain, then divided into 0.6 and the quotient stored back into the corresponding gain register. 2. DC or AC gain. 3. AC offset (if needed). If both AC gain and offset calibrations were performed, it is possible to repeat both to obtain additional accuracy as AC gain and offset may interact. 9.1.4 Temperature Sensor Calibration Temperature sensor calibration involves the adjustment of two parameters - VBE and VBE0. These values must be known in order to calibrate the temperature sensor. See Section 6.13 Temperature Measurement on page 22 for an explanation of VBE and VBE0 and how to calculate TGAIN and TOFF register values from them. 9.1.4.1 Temperature Offset Calibration Offset calibration can be done at any temperature, but should be done mid-scale if any gain error exists. Subtract the measured T register temperature from the actual temperature to determine the offset error. Multiply this error by VBE and add it to VBE0 to yield a new VBE0 value. Recalculate TOFF using this new value. 9.1.4.2 Temperature Gain Calibration Two temperature points far enough apart to give reasonable accuracy, for example 25C and 85C, are required to calibrate temperature gain. Divide the actual temperature difference by the measured (T register) difference for the two temperatures. This gives a gain correction factor. Update the TGAIN register by multiplying it's value by this correction factor. Update VBE by dividing its old value by the gain correction factor. It will be needed for subsequent offset calibrations. 41 CS5467 10. E2PROM OPERATION The CS5467 can accept commands from a serial E2PROM connected to the serial interface instead of a host microcontroller. A high level (logic 1) on the MODE input indicates that an E2PROM is connected. This makes the CS and SCLK pins become driven outputs. After reset and after running the initialization program, the CS5467 begins reading commands from the connected E2PROM. 10.1 E2PROM Configuration 10.2 E2PROM Code The EEPROM code should do the following: 1. Set any Configuration or Control register bits, such as HPF enables and phase compensation settings. 2. Write any calibration data to gain and offset registers. 3. Set energy output pulse width, rate, and formats. 4. Execute a Continuous Conversion command. 5. Set the STOP bit in the Control register (last). A typical connection between the CS5467 and a E2PROM is shown in Figure 13. Below is an example E2PROM code set. -7E 00 00 01 Change to page 1. -60 00 01 E0 Write Modes Register, turn high-pass filters on. -42 7F C4 A9 Write value of 0x7FC4A9 to I1GAIN register. -46 FF B2 53 Write value of 0xFFB253 to V1GAIN register. -50 7F C4 A9 Write value of 0x7FC4A9 to I2GAIN register. -54 FF B2 53 Write value of 0xFFB253 to V2GAIN register. -7E 00 00 00 Change to page 0. -74 00 00 04 Set LSD bit to 1 in the Mask register. -E8 Start continuous conversions -78 00 01 00 Write STOP bit to the Control register (Ctrl) to terminate E2PROM command sequence. The CS5467 asserts CS (logic 0), clocks SCLK, and sends Read commands to the E2PROM on SDO. Command format is identical to microcontroller mode, except the CS5467 will not attempt to write to the EEPROM device. The command sequence stops when the STOP bit in the Control register (Ctrl) is written by the command sequence. VD + E1 E2 5K Pulse Output Counter EEPROM CS5467 SCK SCLK SO SDI SDO MODE 5K CS SI CS Connector to Calibrator Figure 13. Typical Interface of E2PROM to CS5467 Figure 13 also shows the external connections that would be made to a calibration device, such as a notebook computer, handheld calibrator, or tester during meter assembly, The calibrator or tester can be used to control the CS5467 during calibration and program the required values into the E2PROM. 10.3 Which E2PROMs Can Be Used? Several industry-standard serial E2PROMs can be used with the CS5467. Some are listed below: * * * Atmel AT25010, AT25020 or AT25040 National Semiconductor NM25C040M8 or NM25020M8 Xicor X25040SI These serial E2PROMs expect a specific 8-bit command (00000011) in order to perform a memory read. The CS5467 has been hardware programmed to transmit this 8-bit command to the E2PROM after reset. 42 DS714F3 CS5467 11. BASIC APPLICATION CIRCUITS Figure 14 shows the CS5467 configured to measure power in a single-phase, 3-wire system while operating in a single-supply configuration. In this diagram, current transformers (CT) are used to sense the line currents and voltage dividers are used to sense the line voltages. 10 k 5 k L1 N 500 10 500 470 F 2 uF 0.1 F 13 CV+ 0.1 F VIN2+ CS5467 CVdiff R 2 R1 CV- R V- 14 9 CV+ R 1 VIN2VIN1+ PFMON CPUCLK XOUT XIN CV- R V- 10 R I- 19 1/2 RBurden C I- 2 1 4.096 MHz 1/2 RBurden CI+ IIN1RESET 20 IIN1+ RI+ R I- 15 1/2 RBurden C I- 1/2 RBurden CI+ IIN2- C Idiff 16 12 11 23 7 CS 27 SDI 6 SDO 5 SCLK 24 INT 26 E2 25 E1 Serial Data Interface Pulse Output Counter IIN2+ RI+ LOAD Optional Clock Source 28 VIN1- C Idiff CT LOAD 21 CVdiff R2 CT 3 VD+ 18 VA+ ISOLATION (Optional) L2 VREFIN VREFOUT 0.1 F AGND 17 DGND 4 Figure 14. Typical Connection Diagram (Single-phase, 3-wire - Direct Connect to Power Line) DS714F3 43 CS5467 12. PACKAGE DIMENSIONS 28L SSOP PACKAGE DRAWING N D E11 A2 E A e b2 SIDE VIEW A1 L END VIEW SEATING PLANE 1 2 3 TOP VIEW DIM A A1 A2 b D E E1 e L MIN -0.002 0.064 0.009 0.390 0.291 0.197 0.022 0.025 0 INCHES NOM -0.006 0.069 -0.4015 0.307 0.209 0.026 0.0354 4 MAX 0.084 0.010 0.074 0.015 0.413 0.323 0.220 0.030 0.041 8 MIN -0.05 1.62 0.22 9.90 7.40 5.00 0.55 0.63 0 MILLIMETERS NOM -0.15 1.75 -10.20 7.80 5.30 0.65 0.90 4 NOTE MAX 2.13 0.25 1.88 0.38 10.50 8.20 5.60 0.75 1.03 8 2,3 1 1 JEDEC #: MO-150 Controlling Dimension is Millimeters Notes: 1. "D" and "E1" are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm per side. Dimension "b" does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be 0.13 mm total in excess of "b" dimension at maximum material condition. Dambar intrusion shall not reduce dimension "b" by more than 0.07 mm at least material condition. 3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips. 2. 44 DS714F3 CS5467 13. ORDERING INFORMATION Model CS5467-ISZ (lead free) Temperature Package -40 to +85 C 28-pin SSOP 14. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION Model Number CS5467-ISZ (lead free) Peak Reflow Temp MSL Rating* Max Floor Life 260 C 3 7 Days * MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020. DS714F3 45 CS5467 15. REVISION HISTORY Revision Date Changes PP1 FEB 2007 Initial release. PP2 FEB 2007 Corrections to implicitly state that temperature measurement is a secondary function of voltage2 channel. Updated typical connection diagram. Changed Phase Compensation Range from 2.8 to 5.4. F1 MAR 2007 Updated to F1 for quality process level (QPL). F2 JAN 2010 Increased on-chip reference temperature coefficient from 25 ppm / C typ. to 40 ppm / C typ. F3 APR 2011 Removed lead-containing (Pb) device ordering information. Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com IMPORTANT NOTICE "Preliminary" product information describes products that are in production, but for which full characterization data is not yet available. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. 46 DS714F3