GENLINX TMII GS9020A Serial Digital Video Input Processor DATA SHEET DESCRIPTION * fully compatible with SMPTE 259M The GS9020A is specifically designed to deserialize SMPTE 259M serial digital signals. The inclusion of Error Detection and Handling (EDH) ensures the integrity of the data being received from the serial digital interface (SDI). Internal 75 termination resistors allow INTERLINXTM seamless connection with the GS9035A Reclocker or the GS9025A Receiver, thus providing a complete high performance, digital video input processor with EDH, digital sync signal generation, and other system features. * drop-in replacement for the GS9020 * auto-standard operation to 540MHz * embedded EDH and data processing core * selectable loop through or re-serialized EDH-processed serial output * noise immune HVF timing signal outputs * configurable FIFO reset pulse for clearing downstream FIFOs * ANC header and TRS-ID correction for all standards * user controlled output blanking * ITU-R-601 output clipping for active picture area * ancillary data indication * low system power * selectable IC interface or 8-bit parallel port for access to EDH flags and device configuration bits * EDH flags also available on dedicated pins * seamless flag mapping to GS9021 EDH coprocessor * 80 pin LQFP * Pb-free and Green The GS9020A also includes a parallel to serial converter and NRZI scrambler to provide re-serialized, EDH compliant data output. The EDH core implements EDH insertion and extraction according to SMPTE RP-165. This core also generates noise immune timing signals such as horizontal sync, vertical blanking, field ID and ancillary data identification. It also provides many system features such as a FIFO reset pulse (which can be programmed to coincide with either EAV or SAV), TRS-ID and ANC header correction, user controlled output blanking and ITU-R-601 output clipping. The GS9020A has an IC (Inter-Integrated Circuit, IC is a registered Trademark of Philips) serial interface bus and an 8-bit parallel port for external access to all error flags and device configuration bits. APPLICATIONS SMPTE 259M serial digital receiver for composite and component standards including 4:4:4:4 at 540Mb/s with EDH processing; Noise immune digital sync and timing generation; Cost effective EDH insertion and checking for serial routing and distribution applications. ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE Pb-FREE AND GREEN GS9020ACFV 80 pin LQFP Tray 0C to 70C No GS9020ACTV 80 pin LQFP Tape 0C to 70C No GS9020ACFVE3 80 pin LQFP Tray 0C to 70C Yes GS9020ACTVE3 80 pin LQFP Tape 0C to 70C Yes Revision Date: June 2004 Document No. 19922 - 3 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: info@gennum.com www.gennum.com GS9020A FEATURES SDO BUF SDO PARALLEL TO SERIAL CONVERTER WITH SCRAMBLER DESCRAMBLER SDI GS9020A 0 1 BUF SDI SERIAL TO PARALLEL CONVERTER SCI BUF 10 10 FRAMED DATA [9:0] FIFO_RESET SYNC DETECTOR PCLK OUT SCRAMBLER PRESCALER SCI ALIGNING CONTROL UNIT DOUT[9:0] 5 EDH AND DATA PROCESSING CORE HVF CLIP_TRS ANC_CHKSM 4 RESET STANDARDS INDICATOR HOSTIF TRS_ERR 7 DEDICATED FLAG PORT PCLKOUT BLOCK DIAGRAM 2 of 31 19922 - 3 ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE Supply Voltage -0.3V to 6.0V Input Voltage Range (any input) -0.3 to VDD +0.3V 0C to 70C Storage Temperature GS9020A Operating Temperature Range -55C to 150C Lead Temperature (soldering, 10 sec) 260C DC ELECTRICAL CHARCTERISTICS VDD = 5.0 V, TA = 0 - 70C unless otherwise shown. PARAMETER SYMBOL MIN TYP MAX UNITS 4.75 5.0 5.25 V 270Mb/s - 110 - mA 540Mb/s - 190 - mA VCM 3.14 3.65 3.95 V VDIFFIN 450 800 1250 mV RPULLUP - 75 - VCM - 2.7 - V VDIFFOUT - 800 - mV VILMAX - - 0.8 V VIHMIN 2.0 - - V - - 150 A 3 - - 1 A 4 - 10 - pF Supply Voltage VDD Supply Current Unloaded DD High Speed Serial Data and Clock Inputs Serial Data Outputs TTL Compatible CMOS Inputs IN CONDITIONS VIN = VDD or GND CIN TTL Compatible CMOS Outputs NOTES 1 2 VOLMAX at OUT - - 0.4 V VOHMIN at OUT 2.4 - - V - 8 - mA 5 - 4 - mA 6 - 2 - mA 7 OUT NOTES 1. RPULLUP refers to the internal pullup resistor associated with the serial data and clock inputs (see Figure 4). 2. Assuming 100 differential termination resistor as shown in figure 7. Given VDIFFOUT = 800mV and a 100 termination, ISDO = 8mA. 3. The following inputs have internal pull-up resistors: SDOMODE. The following inputs have internal pull-down resistors: ANC_CHKSM, FLYWDIS, FLAG_MAP, RESET, CRC_MODE, FIFOE/S AND HOSTIF_MODE. To ensure reliable operation these pins should be externally connected to GND or Vcc. 4. All other inputs. 5. The following outputs have 8mA drivers (typical): PCLKOUT 6. The following outputs have 4mA drivers (typical): S[1:0], FL[4:0], ANC_DATA, DOUT[9:0], V, F[2:0], H, FIFO_RESET, TRS_ERR, NO_EDH 7.The following outputs have 2mA drivers (typical): P[7:0], STD[3:0], INTERRUPT 3 of 31 19922 - 3 AC ELECTRICAL CHARCTERISTICS VDD = 5.0 V, TA = 0 - 70C unless otherwise shown. GS9020A PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS NOTES Serial Input Clock Frequency SCI - - 540 MHz Serial Data Input Setup Time tSS 600 - - ps 1 Serial Data Input Hold Time tSH 600 - - ps 1 - 5 - % - 360 - ps p-p - 600 - ps - 700 - ps p-p t1 20 - - ns 2 t2 - - 9 ns 2 Serial Data Output Duty Cycle Distortion Serial Output Jitter 540Mb/s at eye crossing Serial Data Output Rise Time Parallel Clock Output Jitter Input Timing 27MHz at 50% voltage level Output Delay Time tOD with 25pF loading T/2 - T/2+7 ns 3 Output Hold Time tOH with 25pF loading T/2-3 - - ns 3 Output Setup Time tOS with 25pF loading T/2-7 - - ns 3 Flag Port Disable Time tFDIS with 25pF loading - - T/2+0.5 ns Flag Port Enable Time tFEN with 25pF loading - - T/2+1 ns IC Clock Frequency SCL - - 400 kHz Host Interface Setup Time tHS 6 - - ns 4 Host Interface Hold Time tHH 6 - - ns 4 Host Interface Output Enable Time tHEN with 25pF loading - - 21 ns 4 Host Interface Output Disable Time tHDIS with 25pF loading - - 10 ns 4 Reset Time Pulse Width tRESET 100 - - ns NOTES 1. The serial clock rising edge should occur at the centre of the data period for optimum performance. (See Figure 1) 2. Since the GS9020A does not have a parallel clock input, it is not possible to define timing details relative to it. Instead the GS9020A has a parallel clock output and all timing information is relative to PCLKOUT. The flag port pins (FL[4:0], F_R/W, S[1:0]) are the only inputs where the timing details are important. The timing requirements are shown in Figure 2. 3. These times are relative to the rising edge of PCLKOUT as shown in Figure 3. Note that the data transitions at the falling edge of PCLKOUT. T is the parallel clock period in ns. 4. The Host Interface signals, P[7:0], R/W, A/D and CS are asynchronous to the parallel clock. 4 of 31 19922 - 3 ANC_DATA TRS_ERR CLIP_TRS ANC_CHKSM BLANK_EN SDOMODE BYPASS_EDH VBLANKS/L SGND SDO SDO SVDD VDD GND FLAG_MAP F2 F1 F0 H V PIN CONNECTIONS DOUT9 DOUT8 DOUT7 DOUT6 DOUT5 DOUT4 DOUT3 DOUT2 DOUT1 VDD GND DOUT0 PCLKOUT FIFO_RESET NO_EDH FLYWDIS INTERRUPT F_R/W S0 S1 SCL/P4 SDA/P3 A2/P2 A1/P1 A0/P0 R/W A/D CS VDD GND RESET STD3 STD2 STD1 STD0 FL4 FL3 FL2 FL1 FL0 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 1 60 2 59 3 58 4 57 5 56 6 55 7 54 8 53 9 52 GS9020A 10 51 TOP VIEW 11 50 12 49 13 48 14 47 15 46 16 45 17 44 18 43 19 42 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 GS9020A VDD GND GND VDD VDDSDI SDI SDI VDDSDI VDDSCI SCI SCI VDDSCI VDD GND HOSTIF_MODE FIFOE/S CRC_MODE P7 P6 P5 PIN DESCRIPTIONS NUMBER SYMBOL TYPE DESCRIPTION 6, 7 SDI, SDI I Differential serial data inputs. 10, 11 SCI, SCI I Differential serial clock inputs. 15 HOSTIF_MODE I Host interface mode select. When HIGH, the host interface is configured for IC mode. When LOW, the host interface is configured for parallel port mode. 16 FIFOE/S I FIFO_RESET pulse control. When HIGH, the output FIFO_RESET pulse occurs on the EAV word. When LOW, the output FIFO_RESET pulse occurs on the SAV word. 17 CRC_MODE I CRC_MODE enable. When HIGH, CRC_MODE is enabled. When LOW, CRC_MODE is disabled. 18 - 20 P[7:5] I/O In parallel port mode, these are bits 7:5 of the host interface address/data bus. In IC mode, these pins must be set LOW. 21 SCL/P4 I/O In parallel port mode, this is bit 4 of the host interface address/data bus. In IC mode, this is the serial clock input for the IC port. 22 SDA/P3 I/O In parallel port mode, this is bit 3 of the host interface address/data bus. In IC mode, this is the serial data pin for the IC port. 23 - 25 A[2:0]/P[2:0] I/O In parallel port mode, these are bits 2:0 of the host interface address/data bus. In IC mode, these are input bits which define the IC slave address for the device. 26 R/W I Parallel port read/write control. When HIGH, the parallel port is configured as an output (read mode). When LOW, the parallel port is configured as an input (write mode). In IC mode, this pin must be set HIGH. 5 of 31 19922 - 3 GS9020A PIN DESCRIPTIONS NUMBER SYMBOL TYPE DESCRIPTION 27 A/D I Parallel port address/data bus control. When HIGH, the parallel port is used for address input. When LOW, the parallel port is used for data input or output. In IC mode, this pin must be set LOW. 28 CS I Parallel port chip select. When CS is LOW and R/W is HIGH, the GS9020A drives the address/ data bus. When CS is LOW and R/W is LOW, the user should drive the address/data bus. When CS is HIGH, the address/data bus is in a high impedance state (Hi - Z). In IC mode, this pin must be set HIGH. 31 RESET I Reset. When LOW, the internal control circuitry is reset. 32 - 35 STD[3:0] O Video standards indication as described in section 1.4 36 - 40 FL[4:0] I/O EDH flag data port to allow access to the EDH flags. 41, 42 S[1:0] I/O Control bits which select whether FF, AP, or ANC EDH flags are active on the EDH flag data port (FL[4:0]). In FLAG_MAP mode, the S[1:0] pins become outputs (see device description). 43 F_R/W I Flag port read/write control. When HIGH, FL[4:0] are configured as outputs allowing EDH flags to be read from the device. When LOW, FL[4:0] are configured as inputs allowing EDH flags to be overwritten in the outgoing EDH packet. In FLAG_MAP mode this pin must be set HIGH. 44 INTERRUPT O Interrupt output. This output goes low when EDH errors occur. This pin is an open drain output and requires an external pullup resistor. If this output is not used, a pullup resistor is not required. 45 FLYWDIS I Flywheel disable. When HIGH, the internal flywheel is disabled. When LOW, the internal flywheel is enabled. 46 NO_EDH O No EDH present indication. When HIGH, indicates EDH packets are not present in the incoming data stream. 47 FIFO_RESET O FIFO Reset output. Asserted LOW during the TRSID word for composite standards and the EAV or SAV word for component standards. 48 PCLKOUT O Parallel clock output. 52-60,49 DOUT[9:0] O Parallel digital video data outputs. 61 V O Vertical sync indication. 62 H O Horizontal sync indication. 63 - 65 F[2:0] O Field indication. F2 is the MSB. 66 FLAG_MAP I FLAG_MAP mode enable. When HIGH, FLAG_MAP mode is enabled. When LOW, FLAG_MAP mode is disabled. 70, 71 SDO/SDO O Differential serial data outputs. 73 VBLANKS/L I Vertical blanking interval control. For NTSC signals, when VBLANKS/L is set LOW the 19 line blanking interval is selected and when set HIGH the 9 line blanking interval is selected. For PAL D2 signals, when VBLANKS/L is set LOW the 17 line blanking interval is selected and when set HIGH the 7 line blanking interval is selected. For PAL component signals VBLANKS/L should be set LOW. 74 BYPASS_EDH I Bypass EDH control. When HIGH, the device allows the EDH packet to pass through unaltered. 75 SDOMODE I Serial data output control. When LOW, the serial data output is re-serialized processed data. When HIGH, the serial data output is the looped through serial input. After changing SDOMODE, the GS9020A must be reset for proper operation. 76 BLANK_EN I Blanking enable. When LOW, incoming data words are set to appropriate blanking levels. 77 ANC_CHKSM I Ancillary checksum updating enable. When HIGH, ancillary checksum updating is enabled. 6 of 31 19922 - 3 PIN DESCRIPTIONS SYMBOL TYPE DESCRIPTION 78 CLIP_TRS I Clip and TRS correction control. When HIGH, the TRS Blanking, ITU-R-601 clipping and TRS insertion features are enabled. 79 TRS_ERR O TRS error indication. When HIGH, indicates a TRS error in the data stream such as a missing TRS, an improperly placed TRS, or an incorrect TRS ID word. 80 ANC_DATA O Ancillary data indication. When HIGH, indicates that an ANC packet is coming out of the device. The output is high from the beginning of the first header word to the end of the checksum word of the ANC packet. 1, 4, 13 VDD Power supply connection for the serial processing circuitry (nominally +5V). 2, 3, 14 GND Ground connection for the serial processing circuitry. 69 SVDD Power supply connection for the serial data outputs. To save power when not using the SDO/ SDO outputs, set this pin to ground. 72 SGND Ground connection for the serial data outputs. 5, 8 VDD_SDI, SDI Power supply connection for the internal 75 ohm pullup resistor (nominally +5V) on the serial data input lines. 9, 12 VDD_SCI, SCI Power supply connection for the internal 75 ohm pullup resistor (nominally +5V) on the serial clock input lines. 29,51,68 VDD Power supply connection for the parallel processing circuitry (nominally +5V). 30,50,67 GND Ground for the parallel processing circuitry. HOSTIF_MODE FLAG_MAP EDH FLAG EXTRACTION CRC COMPARISON/ CALCULATION FRAMED DATA [9:0] 10 VBLANKS/L FLYWDIS H, V, F HVF 5 FLYWHEEL TRS DETECTION ANCILLARY CHECKSUM CALCULATION/ COMPARISON IC INTERFACE HOST INTERFACE/ FLAG PORT ERRORED FIELD COUNTER DEDICATED FLAG PORT 8-BIT PARALLEL INTERFACE FLAGS BYPASS_EDH ERROR FLAGS & FORMAT PACKET 10 10 MUX DOUT[9:0] CRC_MODE TRS_ ERROR TRS COMPARE ANCILLARY CHECKSUM CORRECTION 10 ITU-R-601 CLIPPING TRS BLANKING TRS INSERTION/ CORRECTION NEW CRC CALCULATION IC is a registered Trademark of Philips 10 BLANK_EN CLIP_TRS BLOCK DIAGRAM - EDH AND DATA CORE PROCESSING 7 of 31 19922 - 3 GS9020A NUMBER DETAILED DESCRIPTION The GS9020A EDH coprocessor consists of five major blocks: 1. Data Input/Output Block (with automatic standard detect) GS9020A 2. Flywheel Block The internal pullup resistors allow the GS9020A to be easily interfaced to the GS9025A as shown in Figure 5 and Figure 17. An external diode is required to offset the input signals to the input range of the GS9020A. For maximum signal integrity the GS9025A and GS9020A should be placed as close together as possible. 3. EDH Block 4. Data Processing Block 5. Host Interface (HOSTIF) Block The following convention is used to differentiate device pins from HOST interface table bits. PIN LOGIC OPR XX HOSTIF YY LOGIC OPR MEANING AND XX AND YY OR XX OR YY > XX takes precedence over YY < YY takes precedence over XX PIN HOST BIT DOUT[9:0] The output of the device is 10-bit digital video data and is present on the DOUT[9:0] output pins. PIN LOGIC OPR HOST BIT SDO, SDO SDOMODE 1.1 Serial Video Data Inputs HOST BIT SDI, SDI SCI, SCI Serial data and clock signals are supplied to the GS9020A chip via the SDI/SDI and SCI/SCI pins, respectively. Eight standards are supported: Composite, 4:2:2 Component with 13.5MHz Y sampling, 4:2:2 16 x 9 wide screen with 18MHz Y sampling, and 4:4:4:4 Component Single Link with 13.5MHz Y sampling, all in both NTSC and PAL formats. See Table 1. The GS9020A also provides PECL differential serial data outputs (SDO/SDO). The serial data outputs can operate in one of two modes as controlled by the SDOMODE pin. When SDOMODE is set LOW, re-serialized processed data is output at the SDO/SDO output pins. In this mode it is recommended that the lock output of the GS9025A or GS9035A connected to the RESET input of the GS9020A, and to a pull up resistor. This will effectively reset the GS9020A whenever the signal lock is lost. Note that any GS9020A programming through the host interface will be lost after this reset. It will be necessary to reprogram the GS9020A after each reset. When SDOMODE is set HIGH, the serial input data is supplied directly to the SDO/SDO output pins, bypassing the processing core. After changing SDOMODE, the GS9020A must be reset for proper operation. 8 of 31 19922 - 3 LOGIC OPR 1.3 Reserialized Data Output 1. DATA INPUT/OUTPUT BLOCK LOGIC OPR The PECL serial input signals are first converted to CMOS levels and then deserialized to 10 bit parallel format (based on the TRS headers), descrambled, and then passed to the processing core. 1.2 Parallel Digital Video Data Outputs LOGIC OPR (logic operator) gives the combinational relationship (if one exists), between pins which also have a corresponding HOST bit. This operator governs the signal the GS9020A receives. The following is the list of possible logic operators and their meaning. PIN SDI/SDI and SCI/SCI are high speed Pseudo-ECL (PECL) compatible differential inputs with internal pullup resistors (75 nominally) as shown in Figure 4. Note that each pullup resistor has a dedicated power pin allowing the use of other interfacing topologies. The S bit, used for single link data standards only, is encoded in the TRSID word and indicates if the data is in RGB or YCRCB format as per SMPTE RP174. In automatic standard detection mode, the S bit can be read from the HOSTIF read table. In manual mode, the S bit must be set in the HOSTIF write table. 1.4 Automatic Standard Detection 1.5 Parallel Clock Output PIN LOGIC OPR HOST BIT PIN STD_SEL PCLKOUT STD[3:0] LOGIC OPR HOST BIT STD[3:0] S The device automatically detects the incoming video standard. The detected standard is encoded on the STD[3:0] pins and the HOSTIF read table bits as shown in Table 1 and Table 3. The PCLKOUT pin provides the output parallel clock. All synchronous I/O are timed relative to PCLKOUT. The following listing shows which I/O's are synchronous and which are not. Timing for synchronous outputs is shown in Figure 3. Timing for synchronous inputs is shown in Figure 2. TABLE 1 STANDARD NAME STD[3:0] SYNCHRONOUS ASYNCHRONOUS FL[4:0] P[7:5] S[1:0] SCL/P4 FIFO_RESET INTERRUPT DOUT[9:0] SDA/P3 F[2:0] A[2:0]/P[2:0] NTSC 4:2:2 Component with 13.5MHz Y sampling 0000 NTSC Composite 0001 NTSC 4:2:2 16x9 Widescreen with 18MHz Y sampling 0010 NTSC 4:4:4:4 Single Link with 13.5MHz Y sampling 0011 V R/W PAL 4:2:2 Component with 13.5MHz Y sampling 0100 H A/D PAL Composite 0101 ANC_DATA CS PAL 4:2:2 16x9 Widescreen with 18MHz Y sampling 0110 BLANK_EN FLAG_MAP PAL 4:4:4:4 Single Link with 13.5MHz Y sampling 0111 F_R/W RESET NO_EDH CRC_MODE STD[3:0] VBLANKS/L TRS_ERROR HOSTIF_MODE Noise immunity is included to ensure that momentary signal corruption does not affect the automatic standards detection function. This built in noise immunity results in delayed detection time during power up and when switching between standards. Delays range from as little as eight lines when switching between component standards to as much as four frames when switching between PAL and NTSC standards. If this delay is intolerable, the user can manually set the standard through the HOSTIF write table. To set the standard manually, the STD_SEL bit must be set HIGH and the S bit and STD[3:0] pins/HOSTIF bits set accordingly. The default standard upon reset of the chip is NTSC 4:2:2 component (13.5MHz Y sampling). FIFOE/S FLYWDIS BYPASS_EDH SDO_MODE ANC_CHKSM CLIP_TRS 9 of 31 19922 - 3 GS9020A The serial data output circuits are shown in Figure 6. The serial data outputs are designed to drive 50-75 controlled impedance traces and can be easily connected to the GS9028 cable driver as shown in Figure 7 and Figure 18. Note that to output proper PECL signal levels, a resistor must be connected between the two serial data outputs. 2. FLYWHEEL BLOCK 2.2 Accurate FVH Timing Signals 2.1 FVH Flywheel GS9020A PIN PIN LOGIC OPR HOST BIT F[2:0] FLYWDIS OR FLYWDIS V SWITCHFLYW H LOGIC OPR VBLANKS/L The flywheel's primary function is to provide accurate field, vertical, and horizontal output signals in the presence of noisy or error prone input data. Flywheel synchronization is based on the TRS words in the incoming data stream. The FVH flywheel synchronizes to the incoming data stream in less than two fields once the incoming standard has been detected. Once synchronized, the TRS words in the incoming data stream and those generated by the flywheel are constantly compared to ensure that the flywheel remains synchronized. Noise insensitivity is accomplished by re-synchronizing the flywheel to the data stream only if it is not aligned for long periods of time. For component signals, four mismatches between the EAV signal in the incoming and flywheel generated signals over a window of eight lines will trigger the flywheel to begin re-synchronization. For composite signals, re-synchronization is triggered by mismatches in the TRS encoded line numbers or field bits for 7 consecutive lines. The flywheel can be disabled by asserting the FLYWDIS control signal HIGH. Disabling the flywheel will remove the effective noise immunity. In this mode, FVH values will be decoded directly from the incoming data stream rather than being decoded from the flywheel. Note that when the flywheel is disabled, TRS_BLANK and TRS_INSERT will not function correctly if enabled. Therefore if the flywheel is disabled then so should TRS_BLANK and TRS_INSERT. FLYWDIS is available as an input pin and as a bit in the HOSTIF write table. The SWITCHFLYW control signal is used in applications where the data input to the GS9020A is switched between two synchronous signals. In this case, the two signals may be slightly misaligned and would normally require the flywheel to completely re-synchronize. In this scenario, the re-synchronization time would be undesirable. Asserting the SWITCHFLYW bit of the HOSTIF write table HIGH allows the flywheel to re-synchronize to the new incoming signal at the end of the switching line. For this functionality to operate properly, the two signals must both be in the active picture portion of the switching line at the time of the switch. F[2:0] AND VBLANKS/L The F[2:0] signals indicate the current field of the video data. Three F bits are necessary to accommodate the composite PAL standard which has 8 fields. The F[2:0] bits are available on dedicated output pins and via the HOSTIF read table. Figure 8a and 8b illustrate the position of the F[2:0] transition within a line for component and composite signals, respectively. For component standards only, F0 is used to indicate fields 0 and 1. The lines on which the transitions occur conform to the SMPTE standards. For component signals, the horizontal (H) signal is HIGH during the horizontal blanking region of the output signal, from EAV to SAV inclusive. For composite signals, the H signal remains HIGH only for the 3FF, 000, 000, 000, and TRSID words. Figure 8a and 8b illustrate the H output signal timing for component and composite signals, respectively. The vertical (V) signal timing is dependent on the incoming video standard and the VBLANKS/L control signal. The VBLANKS/L signal is available as an input pin and via the HOSTIF write table and should be set to indicate the form of the incoming data stream. This allows the flywheel to correctly structure the V bit for flywheel synchronization, TRS insertion, and TRS error indication. For component based standards, the transition of the V output signal within a line is shown in Figure 8a. The line on which the V output signal transitions from HIGH to LOW is summarized in the table below. The lines on which the LOW to HIGH transition occurs conform to the SMPTE standards. STANDARD VBLANKS/L=1 VBLANKS/L=0 NTSC 4:2:2 Component (13.5MHz Y sampling) 9/272 19/282 NTSC 4:2:2 16x9 Widescreen (18MHz Y sampling) 9/272 19/282 NTSC 4:4:4:4 Single Link (13.5MHz Y sampling) 9/272 19/282 PAL 4:2:2 Component (13.5MHz Y sampling) 22/335 22/335 PAL 4:2:2 16x9 Widescreen (18MHz Y sampling) 22/335 22/335 PAL 4:4:4:4 Single Link (13.5MHz Y sampling) 22/335 22/335 10 of 31 19922 - 3 HOST BIT For composite based standards, the V output signal is asserted HIGH as described in the following table: 2.4 FIFO Reset Pulse PIN NTSC Composite VBLANKS/L=0 from Line 525/ Sample 768 to Line 9/ Sample 767 inclusive from Line 525/ Sample 768 to Line 19/ Sample 767 inclusive HOST BIT FIFOE/S AND AND from Line 263/ Sample 313 to Line 272/ Sample 767 inclusive from Line 263/ Sample 313 to Line 282/ Sample 767 inclusive VBLANKS/L=1 VBLANKS/L=0 from Line 623/ Sample 382 to Line 5/ Sample 947 inclusive from Line 623/ Sample 382 to Line 15/ Sample 947 inclusive AND AND from Line 310/ Sample 948 to Line 317/ Sample 947 inclusive from Line 310/ Sample 948 to Line 327/ Sample 947 inclusive 2.3 TRS Errors PIN LOGIC OPR FIFO_RESET The GS9020A also provides a FIFO_RESET pulse on the FIFO_RESET output pin. This pin is always HIGH except when the TRSID word is exiting the device as shown in Figure 9. For component standards, a FIFOE/S input pin is used to determine if the FIFO_RESET pulse occurs during the EAV or SAV word of the outgoing data. If FIFOE/S is HIGH, the active low pulse of the FIFO_RESET output pin occurs during the EAV word. If FIFOE/S is LOW, the active low output pulse occurs during the SAV word. For composite signals the FIFOE/S pin has no effect since there is only one TRS-ID word per line. This feature is useful for synchronizing line store FIFOs that follow the GS9020A. 3. EDH PROCESSING BLOCK LOGIC OPR TRS_ERR This section describes the GS9020A's EDH features and functionality. HOST BIT TRS_ERR 3.1 Error Flags The flywheel is used to indicate TRS errors. These errors are detected by comparing the TRS in the incoming data stream with the expected TRS based on the internal flywheel. If a mismatch occurs, the TRS_ERR signal is immediately set HIGH and maintained HIGH until a correct TRS occurs. The types of TRS errors detected are: PIN LOGIC OPR HOST BIT INCOMING ERROR FLAGS OUTGOING ERROR FLAGS STICKY IN STICKY OUT * TRS missing * TRS in wrong location * TRS-ID is different from the one generated by the flywheel OVERWRITE VALUES OVERWRITE CONTROL RO_CTRL RESERVED WORDS (INCOMING) The TRS_ERR signal is available as an output pin and via the HOSTIF read table. The TRS_ERR signal should only be considered valid if the flywheel is enabled. RESERVED WORDS (OUTGOING) All 15 EDH error flags can be read from the HOSTIF read table. The INCOMING ERROR FLAGS represent the EDH error flags present in the incoming EDH packet. The OUTGOING ERROR FLAGS represent the EDH error flags present in the outgoing EDH packet (after modification by the GS9020A). Please note that the EDH flags can also be accessed using the flag port as described later. The INCOMING and OUTGOING ERROR FLAGS, the incoming Validity bits (FFV and APV), and the EDH_CHKSM bit can be made "sticky". 11 of 31 19922 - 3 GS9020A PAL Composite VBLANKS/L=1 GS9020A Sticky error flags that detect an error for a field remain asserted until a HOSTIF read is performed on those error flags. Sticky mode allows the user to perform HOSTIF reads on the error flags to detect if any errors have occurred since the last read, and are particularly useful when a read cannot be performed after every field. When STICKY IN is asserted HIGH, the incoming flags and validity bits are in sticky mode. When STICKY OUT is asserted HIGH, the outgoing flags and the EDH_CHKSM bit are in sticky mode. Note that the INTERRUPT signal is derived from these signals so that it too becomes sticky. STICKY IN and STICKY OUT are available in the HOSTIF write table. The ERROR FLAGS and the EDH_CHKSM bit are sticky HIGH. That is, once they are set HIGH, they remain HIGH until a read operation. The Validity bits are sticky LOW. That is, once they are set LOW, they remain LOW until a read operation. In some applications, the user may wish to insert user defined EDH error flags into the outgoing EDH packet. The desired outgoing error flags are written into the OVERWRITE VALUES words of the HOSTIF write table and are placed in the outgoing EDH packet when the corresponding OVERWRITE CONTROL bit is asserted HIGH. See Table 2 for the HOSTIF Write Table. The GS9020A also allows the user to overwrite the seven reserved words of the OUTGOING EDH packet. When RO_CTRL (Reserved Word Overwrite Control) is asserted HIGH, the GS9020A overwrites the reserved words in the OUTGOING EDH packet with those specified in the HOSTIF write table. If RO_CTRL is LOW, the GS9020A does not alter the reserved words. RO_CTRL is a control bit in the HOSTIF write table. The reserved words of the INCOMING EDH packet are also available via the HOSTIF read table. LOGIC OPR The INCOMING FF and AP CRC values for the Full Field (FF) and Active Picture (AP) regions can be read from the HOSTIF read table. Similarly, the OUTGOING (calculated) FF and AP CRC values for the Full Field and Active Picture regions can be read from the HOSTIF read table. 3.3 Validity Bit PIN HOST BIT INCOMING FF CRC OUTGOING FF CRC INCOMING AP CRC OUTGOING AP CRC HOST BIT FFV APV The VALIDITY (V) bits (as per SMPTE 165) present in the incoming EDH packet are used to indicate whether the CRC values are valid or invalid. If the V bit is HIGH, the CRC value is considered valid. In this case, the incoming CRC value is compared with the calculated CRC value to identify errors. If the V bit is LOW, the incoming CRC is invalid and a CRC comparison is not performed. If the device receives an EDH packet with the V bit set LOW it behaves as follows: 1. EDH = 0 (Not asserted for an invalid CRC) 2. EDA = EDAin "OR" EDHin (EDA calculated as usual) 3. A new calculated CRC value replaces the invalid one in the output EDH packet 4. The V bit will be set HIGH in the output EDH packet The incoming V bits for the Full Field and Active Picture regions are available in the HOSTIF read table as FFV and APV, respectively. Outgoing full field (FFV) and active picture (APV) validity bits are set HIGH unless explicitly over-written through the HOSTIF write table or the flag port. Since the device has the potential of modifying the full-field and active picture data with features like ITU-R-601 clipping and TRS insertion, the full field and active picture CRC values must be calculated for both the incoming and outgoing data streams. The calculated CRC values based on the incoming data stream are used for comparison with the embedded CRC values. However, the calculated CRC 12 of 31 19922 - 3 LOGIC OPR 5. Depending on whether one or both or FFV or APV is low, the Unknown Error Status (UES) flag corresponding to either FF or AP or both, is set HIGH in the output data. (No CRC check could be performed, so the data may or may not contain errors). 3.2 CRC Calculation And Updating PIN values based on the outgoing data stream are the ones inserted into the data stream. As a result, the CRC values in the outgoing data stream correctly reflect the contents of the outgoing data stream. 3.4 Ancillary Checksum Verification 3.6 ANC_DATA PIN LOGIC OPR HOST BIT PIN ANC_CHKSM OR ANC_CHKSM ANC_DATA LOGIC OPR HOST BIT EDH_CHKSM When implementing applications which use the EDH core (ie. BYPASS_EDH set LOW), ANC_CHKSM will indicate a downstream FF/AP EDH error when an illegal/non-allowed (3FCH-3FFH) ANC_CHKSM input value is detected. As such, these values should not be present in the incoming data and the corresponding FF/AP EDH errors should not occur. However, if the user wishes to disable the ANC_CHKSM function, it can be deactivated by setting both the ANC_CHSKM pin and the ANC_CHKSM host interface bit LOW. If the chip is receiving ANC EDH flag information through the flag port or the HOSTIF, then the ANC EDH flag generated by the ancillary checksum verification block will be overwritten. However, the additional FF/AP EDH flag will still appear at the next downstream chip if an illegal checksum of 3FCH-3FFH was detected and the ANC_CHKSM function was enabled. 3.7 NO_EDH PIN NO_EDH In receive mode, a UES flag is set HIGH in the outgoing EDH packet if the corresponding UES flag was HIGH in the incoming packet or if the corresponding V bit was LOW. (For example, if the incoming Active Picture V bit is LOW, the outgoing Active Picture UES bit will be HIGH). If there is no EDH packet in the incoming data, all three UES flags (ANC, AP, FF) are set HIGH. HOST BIT NO_EDH Some input data streams may lack the EDH packet. In such cases, the NO_EDH output pin or HOSTIF read table bit is asserted HIGH. If only a few fields lack the EDH packet, the NO_EDH pin/bit will be asserted only for those fields. In determining if the input data stream contains an EDH packet, the GS9020A looks for two things. First the presence of an ANC packet with the header 000 3FF 3FF 1F4 and second that the ANC header is in the right spot for the video standard detected. The NO_EDH signal is a logical NAND of these two cases. If either one is false, the NO_EDH flag is set. 3.8 ERRORED FIELD COUNTER PIN LOGIC OPR HOST BIT ERRORED FIELD COUNTER CLR[1:0] If a checksum error is detected in the EDH packet itself, an additional separate error flag, EDH_CHKSM is set HIGH in the HOSTIF read table. 3.5 UES Error Flag Updating LOGIC OPR ERROR SENSITIVITY BITS The device has a 24 bit ERRORED FIELD COUNTER. The counter increments by one on the occurrence of one or more error flags in an OUTGOING EDH packet. The error flags that can increment the counter are user-selectable through the 16 ERROR SENSITIVITY bits in the HOSTIF write table. The error flag SENSITIVITY bits are active LOW, so that if a particular sensitivity bit is set LOW, the counter is sensitive to errors of that type in the OUTGOING EDH packet. The EDH_CHKSM sensitivity bit is active HIGH. There are four modes of counter operation. The mode is set through 2 bits in the HOSTIF write table, denoted CLR1 and CLR0. 13 of 31 19922 - 3 GS9020A For each received ANC packet in the incoming data, the device compares the calculated checksum value to the embedded checksum for that ANC packet. If the checksum values do not match for any ANC packets within a field, an error is reported via the ancillary EDH flag in the EDH packet. In addition, if the ANC_CHKSM input pin or HOSTIF write table bit is asserted HIGH, the ancillary checksum correction block is enabled and the checksum in the ANC packet is replaced with the calculated one. This update is required to prevent the ANC data error from being flagged at every downstream EDH chip. The ANC_DATA signal is set HIGH when an ancillary data packet is exiting the GS9020A. This pin is asserted from the start of the first header word through to the end of the checksum word of the ANC packet, inclusive, as shown in Figure 10. GS9020A CLR1 CLR0 0 0 Normal 0 1 Reset Counter to Zero 1 0 Auto Reset 1 1 Hold Counter at Zero 3.10 Flag Port MODE OF OPERATION PIN > OVERWRITE VALUES S[1:0] FL[4:0] 3. 9 INTERRUPT Signal LOGIC OPR HOST BIT F_R/W In "Normal" mode the counter operates as previously discussed, such that the counter increments on detection of any error for which the sensitivity flags are set HIGH. If "Reset Counter to Zero" mode is selected, the counter is reset to zero and begins counting again. The mode of operation will immediately return to 00 (normal mode) once the counter resets. In "Auto Reset" mode, the counter behaves in the normal fashion, except that it resets to zero every time a HOSTIF read of the lowest 8 bits of the error counter (address 17) is performed. This functionality allows the chip to count the number of errors since the last read. The "Hold Counter at Zero" mode instantly freezes the counter at zero until it is moved into one of the other modes. PIN LOGIC OPR HOST BIT INTERRUPT An interrupt output pin (INTERRUPT) is also available on the GS9020A. The INTERRUPT output is asserted LOW for each field that contains errors in the outgoing EDH packet. The sensitivity flags used for the 24 bit errored field counter also apply to the interrupt signal. As a result, the interrupt can be made sensitive to any particular flags. The INTERRUPT signal is stable after an EDH packet exits the device and before the subsequent EDH packet enters the device as shown in Figure 11. In addition to the HOSTIF tables, the EDH error flags can also be read and written via the synchronous flag port. The five flag port pins, FL[4:0], allow access to all 15 error flags. The select pins S[1:0] control which flags are read/written as outlined below. If the flag port is not going to be used, it is best to set F_R/W high, leave FL[4:0] unconnected, and set S[1:0] to any value desired (but not floating). 3.10.1 Write Mode When the F_R/W pin is LOW, the flag port is in write mode and the FL[4:0] pins are configured as inputs. After writing to the flag port, the GS9020A inserts the written flags into the next outgoing EDH packet. Note that external flag overwriting via the flag port takes precedence over HOSTIF overwriting but the flag port writing only affects the next outgoing EDH packet. Following this, if the flag port is not written to again, flag operation is returned to normal EDH functionality (unless it is being overwritten through the HOSTIF). The data present on the FL[4:0] output pins, as controlled by the S[1:0] pins, is summarized below. Write Mode, F_R/W = 0 S[1:0] FL4 FL3 FL2 FL1 FL0 00 FF UES FF IDA FF IDH FF EDA FF EDH 01 AP UES AP IDA AP IDH AP EDA AP EDH 10 ANC UES ANC IDA ANC IDH ANC EDA ANC EDH 11 IN/OUT APV FFV 0 0 If the STICKY OUT control bit is asserted HIGH, the interrupt remains asserted LOW until a HOSTIF read is performed on the flag that caused the interrupt. The INTERRUPT output is an open drain output and as a result requires an external pull-up resistor. A 10k resistor value is recommended. If this output is not used, a pullup resistor is not required. In addition to overwriting the 15 error flags, the outgoing validity bits for the active picture (APV) and full field (FFV) can be overwritten via the flag port. The IN/OUT bit has no effect on writes to the error flags. IN/ OUT is a control bit used to determine if the flags read from the flag port during flag port read cycles represent incoming or outgoing EDH flags. If this bit is set HIGH, all subsequent reads are from the incoming EDH packet. If this bit is set LOW, then all subsequent reads are from the updated outgoing packet. When the IN/OUT bit is written to, the value remains latched until it is re-programmed. The IN/ OUT bit is set LOW upon reset of the chip. 14 of 31 19922 - 3 3.10.2 Read Mode When the F_R/W pin is HIGH, the flag port is in read mode and the FL[4:0] pins are configured as outputs. The data present on the FL[4:0] output pins, as controlled by the S[1:0] pins, is summarized below. Read Mode, F_R/W = 1 FL4 FL3 FL2 FL1 FL0 00 FF UES FF IDA FF IDH FF EDA FF EDH 01 AP UES AP IDA AP IDH AP EDA AP EDH 10 ANC UES ANC IDA ANC IDH ANC EDA ANC EDH 11 EDH_ CHKSUM APV FFV S Note that the 15 error flags can be read from the incoming or outgoing EDH packet (see IN/OUT control bit above). However, the EDH_CHKSM flag available on pin FL4 when S[1:0] = 11 is only valid if IN/OUT is LOW. Also, the APV and FFV bits available on pins FL[3:2] when S[1:0] = 11 are only valid when IN/OUT is HIGH (that is, the validity bits are always read from the incoming EDH packet). The S bit is available regardless of the state of the IN/OUT bit. The FLAG PORT is synchronous to the internal parallel clock and hence adequate timing for writing must be provided as indicated in the AC timing information and Figure 2. FLAG PORT read/write cycles, relative to the data stream, should take place as outlined in section 5.3 (HOST INTERFACE READ/WRITE TIMING). 3.11 CRC_MODE and FLAG_MAP Mode PIN LOGIC OPR HOST BIT OR FLAG_MAP CRC_MODE FLAG_MAP 3.10.3 FLAG PORT Read/Write Timing Figure 12a shows a FLAG PORT write cycle followed by a FLAG PORT read cycle and illustrates the read/write timing requirements. Note that the signals are not latched in exactly on the rising edge of PLCKOUT (as described in Note 2 of the AC electrical table), but are shown as being latched in on the rising edge for simplicity only. A write cycle is initiated by changing the F_R/W signal from HIGH to LOW. The first time the device samples the F_R/W LOW (at t0) it is instructed to stop driving the FL[4:0] pins. On each subsequent clock cycle (and F_R/W LOW) the device latches in the data present on S[1:0] and FL[4:0] (at t1, t2, t3 and t4). In this example, the S[1:0] pins begin at "00" and are incremented each clock cycle to update all the error flags, validity bits, and the IN/OUT control bit. Note that if a write cycle is performed to update, say the FF error flags (S[1:0] = 00), only the FF flags are updated, and the others are unaffected. A delay time, tFDIS, is necessary to change the FL[4:0] pins from output mode to input mode as defined in the AC timing table and shown in Figure 12b. The external controller can begin to drive the FL[4:0] bus after this delay time. A simple way to allow for this is to wait one clock cycle before starting to drive the FL[4:0] port and thus prevent bus contention (but set the S[1:0] inputs when F_R/W goes LOW so that flags are not unintentionally affected). A common configuration is to have an input EDH chip that checks for errors at the input of a piece of equipment, followed by a processing block that manipulates the data, followed by an output EDH chip that updates the CRC values in the EDH packet before the data exits the equipment. Because the processing block changes the data values, the CRC values in the EDH packet no longer represent the data stream. The output EDH chip updates the CRC values to correctly reflect the newly modified data. To prevent the output EDH chip from indicating erroneous CRC errors on each field, the GS9020A has two special modes of operation, CRC_MODE and FLAG_MAP mode. 3.11.1 CRC_MODE In CRC_MODE, the CRC values in the EDH packet are updated by the chip but the error flags are preserved and unaltered, unless they are overwritten via the HOSTIF or the FLAG PORT. This mode should be used by the output EDH chip to prevent the newly processed data from creating misleading EDH errors due to CRC mismatches. The device is placed in CRC_MODE by asserting the CRC_MODE pin HIGH. 15 of 31 19922 - 3 GS9020A S[1:0] At t5, the F_R/W pin is sampled HIGH, indicating a read operation. Also at this time, the device reads in the information on the S[1:0] pins. Upon sampling a read operation, the device will begin driving the FLAG PORT after a delay, tFEN (see Figure 12c), with invalid data. The requested information is output on the FL[4:0] pins on the subsequent clock, t6, (plus an output delay time, see AC timing table and Figure 3). That is, there is a one clock latency between sampling of the S[1:0] pins and when the corresponding output information is presented on the FL[4:0] pins. In this example, the S[1:0] pins begin at "00" and are incremented each clock cycle to read all the error flags, EDH_CHKSM, validity, and S bits. GS9020A CRC_MODE is applicable when the processing circuitry does not corrupt the EDH packet, as illustrated in Figure 13a. In this configuration, the input EDH chip operates in normal mode while the output EDH chip is in CRC_MODE. In this scenario, the input IC receives the EDH packet and does normal EDH processing. The output IC updates the EDH packet with new CRC values but passes the EDH flags through unaltered. Because of this, erroneous EDH flag handling by the second EDH chip is not performed. 3.11.2 FLAG_MAP Mode In FLAG_MAP mode, the FLAG PORT is used to read EDH flags from the GS9020A and write them to another EDH chip. To enable FLAG_MAP mode, the FLAG_MAP mode pin and the F_R/W pin must be asserted HIGH (set F_R/W at least one cycle ahead of FLAG_MAP). After a delay of tFEN, the FL[4:0] and S[1:0] pins of the FLAG PORT become outputs and can be connected to the chip which you wish the GS9020A to write the FLAG data to. In this mode the GS9020A automatically increments the value of S[1:0] and subsequently displays the appropriate flags on the FL[4:0] port, synchronous to the rising edge of PCLKOUT. This is illustrated in Figure 12d. Figure 12d displays three properties of the FLAG PORT in FLAG_MAP mode. First, each data is present on the FLAG PORT for two clock cycles to eliminate any setup time violations that might occur due to clock data skew between chips placed far apart. However, the designer must still ensure that the hold time is satisfied. Second, the S[1:0] pins never cycle to the value of "11" in FLAG_MAP mode since the values contained in the FL[4:0] register when S[1:0] ="11" are not considered EDH flags. Also, the chip cycles S[1:0] in the sequence "01", "00", "10" since this is the order in which the flags are stored and subsequently decoded from the EDH packet. Finally the S[1:0] pins only change value after receipt of an EDH packet and are thus static between packets. During this inter-packet time, the S[1:0] pins display a value of "01" and the FL[4:0] pins display the ANC EDH flags from the preceding EDH packet. For reliable data output on the FLAG PORT, switching the FLAG_MAP pin when an EDH packet is exiting the device is not advised. Also, if the EDH core is bypassed by asserting the BYPASS_EDH pin HIGH, the flag port will always display zeros. This is because the incoming flags (which will be decoded and written to the HOSTIF table) will not be updated to reflect the condition of the input data, and as a result no outgoing flags will be generated (the FLAG PORT only displays the outgoing EDH flags). used to route the EDH flags from an input EDH chip around the processing core and write them to an output EDH chip. In this configuration, the input IC is in FLAG_MAP mode. It receives the EDH packet, does normal EDH processing and transfers the new EDH flags to the output IC. The output IC, which is not in FLAG_MAP mode but is in write mode (FLAG_MAP and F_R/W stay LOW) receives these flags as they are written to it by the EDH chip. The output EDH chip then updates the EDH packet with the new CRC values and inserts the preserved EDH flags that have been transferred from the input IC. A diagram of this can be found in Figure 13b. Because the flags are output as soon as they are decoded, the maximum processing latency supported between the two EDH chips is the number of clock cycles in the shortest field of the standard minus 15 clock cycles. For example, D1 has one field of 262 x 1716 = 449592 clock cycles, and one field of 263 x 1716 = 451308 clock cycles. Thus the maximum latency for D1 is 449592 - 15 = 449577 clock cycles. Any additional latency requires that the flags be delayed before they can be piped to the output chip. Since writing to the flag port takes precedence over the HOSTIF writing, if any of the flags need to be forced at the output EDH chip, external logic in the routing path must be added. Alternately, the HOSTIF of the EDH chip can be used to perform any additional flag masking. 3.12 BYPASS_EDH Processing LOGIC OPR HOST BIT BYPASS_EDH OR BYPASS_EDH EDH processing can be bypassed by asserting the BYPASS_EDH pin or HOSTIF write table bit HIGH. When bypassed, EDH packets pass through the chip unaltered. Overwriting information in the EDH packet via the HOSTIF write table or the FLAG PORT has no effect. Data processing in the chip (as described below) can still occur even if BYPASS_EDH is asserted. In this case, valid incoming error flags can be read via the IC or parallel port interface. However, reading outgoing error flags via the host port or the flag port returns values of 0. FLAG_MAP mode can be used to write EDH flags to any chip, the most common use being applicable when the processing circuitry following the EDH chip corrupts the EDH packet. In this case, the FLAG_MAP mode can be 16 of 31 19922 - 3 PIN 4. DATA PROCESSING BLOCK 4.2 ITU-R-601 Clipping The GS9020A contains advanced data processing features that can simplify system design requirements. These include: PIN LOGIC OPR HOST BIT 601_CLIP TRS Blanking, * ITU-R-601 Clipping * Data Blanking, * TRS Insertion, and * ANC Header updating This feature operates on the active picture portion (as defined in RP165) of the data stream only. When the 601_CLIP bit of the HOSTIF write table is asserted HIGH, the device remaps all reserved data words in the active picture to values compliant with ITU-R-601. That is, 000-003 is clipped to 004 and 3FCH-3FFH is clipped to 3FBH. It is important to note that these processing functions occur in the GS9020A in the order listed above. When implementing applications which use the EDH core (ie. BYPASS_EDH set LOW), TRS blanking, data blanking, and TRS insertion will indicate a downstream FF/AP EDH error when a 3FCH-3FFH input data value is blanked out or overwritten to a value less than 3FBH. As such, users may wish to disable data blanking, TRS blanking and TRS insertion by setting the BLANK_EN pin HIGH, the CLIP_TRS pin LOW, and leaving the corresponding host interface bits at their power-on default values when implementing applications which use the EDH core. 4.1 TRS Blanking PIN LOGIC OPR HOST BIT 4.3 Data Blanking PIN LOGIC OPR HOST BIT BLANK_EN AND BLANK_EN Asserting the BLANK_EN pin or the corresponding HOSTIF write table bit LOW causes the corresponding input data to be forced to blanking levels. This is a dynamic control allowing the user to individually select which data words are to be blanked. TRS and EDH insertion occurs after data blanking so if all these features are being used, the output data stream continues to have TRS words and EDH packets present, even if the BLANK_EN is constantly held LOW. The outgoing EDH packet will contain the correct CRC values for the blanked fields since the CRC values are calculated and inserted just prior to the data exiting the device. TRS_BLANK When asserted HIGH, TRS_BLANK (HOSTIF write table) will blank out any incorrectly positioned TRS words with respect to the flywheel. The blanking values used will be appropriate for the detected video standard as described below in the Data Blanking section. When TRS_INSERT is enabled and TRS_BLANK is not, there may be 4 TRSs per line in the outgoing data stream during a standard switch. Similarly, if TRS_BLANK is enabled and TRS_INSERT is not, then there may be 0 TRS per line during a switch. In most applications, these features should be either both enabled or both disabled to maintain only two TRSs per line. TRS blanking will function incorrectly if the flywheel is disabled. Thus if the flywheel is disabled the TRS_BLANK function should be disabled as well. The blanking values in hexi-decimal notation for each standard are as follows: NTSC/PAL 4:2:2 200 040 200 040 (CB:Y:CR:Y) NTSC 4sc 0F0 PAL 4sc 100 NTSC/PAL 4:4:4:4 040 040 040 040 (B:G:R:A) 200 040 200 040 (CB:Y:CR:A) Note that the device must first detect the incoming standard in order for the proper blanking values to be inserted. 4.4 TRS Insertion TRS words, based on the internal flywheel, can be inserted into the outgoing data stream by asserting HIGH the TRS_INSERT bit of the HOSTIF write table. Note that for proper TRS insertion, the incoming standard must be detected and the flywheel synchronized. That is, the GS9020A does NOT provide proper TRS insertion for unformatted video data (video without TRS words). 17 of 31 19922 - 3 GS9020A * 5.0 HOST INTERFACE TABLES GS9020A PIN LOGIC OPR HOST BIT PIN TRS_INSERT HOSTIF_MODE In the case where the input signal disappears, TRSs will continue to be inserted based on the last detected standard. Further, if a TRS is already in the correct location, it will be overwritten which may have the effect of correcting the TRS-ID word. TRS insertion will function incorrectly if the flywheel is disabled. Thus if the flywheel is disabled the TRS_INSERT function should be disabled as well. 4.5 Clipping And TRS Blanking/Insertion PIN LOGIC OPR HOST BIT CLIP_TRS OR 601_CLIP LOGIC OPR HOST BIT The HOST INTERFACE TABLES (HOSTIF) refer to memory locations within the GS9020A which store functional information about the device. There are two tables, a write table and read table. The write table is organized into 15 word locations (each 8 bits wide) as shown in Table 2 and is used to set various configuration/flag bits. The read table is organized into 23 word locations (each 8 bits wide) as shown in Table 3 and is used to read status information from the device. The HOSTIF tables can be accessed via an IC (InterIntegrated Circuit) serial interface or an 8-bit parallel interface. The HOSTIF_MODE pin selects which interface is used. If the HOSTIF_MODE pin is HIGH, the HOSTIF operates in IC mode. If the HOSTIF_MODE pin is LOW, the HOSTIF operates in parallel mode. TRS_BLANK TRS_INSERT Asserting the CLIP_TRS pin HIGH turns on three features described above: ITU-R-601 Clipping, TRS Blanking, and TRS Insertion These three functions can also be turned on individually through the HOSTIF as described above. THE CLIP_TRS pin is logically ORed with each of the three bits from the HOSTIF table. As a result, as long as the CLIP_TRS pin is asserted, these functions cannot be turned off via the HOSTIF. Note that many bits stored in the tables are also available as device pins. Bits in the write table that have a default value of 0 are logically ORed with the corresponding pin. Write table control bits VBLANKS/L and BLANK_EN, which have a default value of 1, are logically ANDed with the corresponding pin. However, write table control bit ANC_CHKSM, which has a default value of 1, is logically ORed with the corresponding pin. Therefore, to use the ANC_CHKSM pin, the ANC_CHKSM control bit must first be set to 0. If the HOST interface is not going to be used, the best way to set the related pins is as follows: HOSTIF_MODE = LOW CS = HIGH R/W = HIGH 4.6 Ancillary Header A/D = DON'T CARE (BUT NOT FLOATING) PIN LOGIC OPR P[7:0] = N/C HOST BIT ANC_HEADER Updating of the ANC headers can occur to facilitate 8-bit to 10-bit conversion. If the ANC_HEADER bit of the HOSTIF write table is set HIGH, all 3FC-3FF data values corresponding to component ANC headers are remapped to 3FF in the output data stream. For example, if 8 bit data is input to the device, the ANC header of 00, FF, FF will appear as 000, 3FC, 3FC and will be remapped to 000, 3FF, 3FF by the GS9020A. 18 of 31 19922 - 3 B) Signals are "strobed" into/out of the parallel port on the falling edge of the CS signal. Setup and hold times, as defined in the AC timing tables, are relative to this edge and must be met (see Figure 14a) 5.1 IC Serial Interface PIN LOGIC OPR HOST BIT SCL SDA The IC interface consists of a bi-directional serial data pin (SDA) and a serial clock input pin (SCL). In addition, 3 input pins, A[2:0] are provided to assign the chip one of eight possible IC addresses (0001A2A1A0). During an IC write operation, the first byte written to the chip (after the device has been addressed) is interpreted as the starting HOSTIF write table address for the communication. The next byte is interpreted as data to be written to this address. The address then automatically increments so that the following bytes are written to subsequent addresses. When executing a read operation, a write must be performed first to load the starting address. After this, bytes read from the chip will begin at this address and will autoincrement. If the read operation is halted and communication with the chip is later established for another read, the chip will resume reading at the next HOSTIF memory address. In IC mode, P[7:5] and A/D must be set LOW while R/W and CS must be set HIGH. LOGIC OPR A read example follows the write cycle. Note that the read cycle begins with a write operation to indicate the starting address. At t2, R/W is LOW (indicating write), A/D is HIGH (indicating address) and P[7:0] represent the starting address for the read cycle. After sufficient hold time, the microcontroller releases the P[7:0] bus and the R/W is asserted HIGH to indicate a read operation. At t3, the CS is asserted low causing the GS9020A to present the required data on the P[7:0] bus. If two consecutive data read or write operations are performed, the device will automatically increment the address. However, for a completely random-access operation, the address can be specified prior to every data read or write operation. 5.2 Parallel Interface PIN A write cycle to the parallel interface is shown in Figure 14c. The starting address of the operation is written to the chip by putting the R/W pin LOW (indicating write) and the A/D pin high (indicating ADDRESS). At t0, the falling edge of CS strobes in the information. Following this, the A/D line should be asserted LOW indicating data. The R/W line remains LOW indicating a write operation and at t1 the data is strobed into the device. HOST BIT P[7:0] 5.3 Host Interface Read/Write Timing A/D R/W CS The asynchronous parallel interface consists of an 8-bit multiplexed address/data bus (P[7:0]), a chip select pin (CS), a read/write pin (R/W), and an address/data pin (A/D). The following should be noted when interfacing to the parallel port: A) Read/Write cycles via the parallel interface are completely independent and asynchronous to the parallel clock PCLKOUT. Figure 15 illustrates valid times for reading/writing information from the HOSTIF tables. It represents two fields of video data entering and exiting the GS9020A. The relative position of the EDH packet in the data stream is also shown. (Note that the EDH packet entering the device at t0, EDH F0, represents the EDH information from the previous field, FIELD 0). It is safe to read or write EDH information at least two lines after an EDH packet exits the chip but before the subsequent EDH packet enters the chip. Reading during the time interval shown will show values from EDH F0. Writing during the time interval shown will affect EDH F1. Note that the above read/write timing should also be observed when reading/writing flag information via the FLAG PORT. 19 of 31 19922 - 3 GS9020A A[2:0] C) The GS9020A drives the P[7:0] bus when the R/W pin is HIGH and the CS pin is LOW. At all other times, the P[7:0] port is in a high impedance state. The host interface enable and disable times are shown in Figure 14b and are specified in the AC timing information. In this figure, the rising/falling edges of R/W and CS are not aligned to illustrate that the state of the P[7:0] I/Os is only a combinatorial function of the R/W and CS pins. 6.0 RESET PIN LOGIC OPR HOST BIT GS9020A RESET Setting the RESET input pin LOW re-initializes the internal control circuitry including returning all HOST interface programming values to their original default values. An internal power-on-reset cell is also present in the device so that device initialization occurs on power-up. Figure 16a illustrates the reset circuitry. The internal power-on reset circuit of the GS9020A is sensitive to the rise time of the power supply, hence an external power on reset chip or board level reset line is strongly recommended. When using this technique, the user must ensure that a minimum pulse width of 100ns is present on the reset line. In applications where a board-level reset is not available, a circuit similar to figure 16b can be used to ensure correct reset on power-up. The RESET pin will typically take 1.4ms to reach 2.5V on power up, but can take longer for power supplies with slower rise times. A bleed resistor such as the one shown (20k) will assist the capacitor to discharge once power is removed. The user should allow the capacitor to discharge to at least 0.5V before power is reapplied, to permit a full internal reset. The time taken by the RESET pin to reach 0.5V on power down, is dependent upon the fall time of the power supply. 20 of 31 19922 - 3 0 0 0 0 0 11 12 13 14 15 0 0 9 10 0 0 7 8 0 6 0 5 RW7 B3 RW6 B5 RW5 B7 RW3 B3 RW2 B5 RW1 B7 AP UES FF UES AP UES FF UES AP UES FF UES 601_CLIP 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 RW7 B2 RW6 B4 RW5 B6 RW3 B2 RW2 B4 RW1 B6 AP IDA FF IDA AP IDA FF IDA AP IDA FF IDA BLANK_EN VBLANKS/L STICKY OUT 6 NOTE: 1. Superscripts denote default settings upon reset. RESERVED (OUTGOING) ERROR SENSITIVITY BITS OVERWRITE CONTROL 0 4 0 3 OVERWRITE VALUES 0 2 STICKY IN 0 1 CONFIGURATION 7 ADDRESS WRITE Table TABLE 2: GS9020A Host Interface Write Table 0 0 0 0 0 0 0 0 0 0 RO_CTRL RW6 B3 RW5 B5 RW4 B7 RW2 B3 RW1 B5 AP IDH FF IDH AP IDH FF IDH 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 ANC_HEADER STD SEL CLR1 FFV RW6 B2 RW5 B4 RW4 B6 RW2 B2 RW1 B4 AP EDA FF EDA AP EDA FF EDA AP EDA FF EDA BYPASS_EDH S CLR0 4 1 0 0 0 5 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 APV RW7 B7 RW5 B3 RW4 B5 RW3 B7 RW1 B3 AP EDH FF EDH AP EDH FF EDH AP EDH FF EDH FLAG_MAP STD3 SWITCH FLYW 3 RW7 B6 RW5 B2 RW4 B4 RW3 B6 RW1 B2 ANC EDA ANC UES ANC EDA ANC UES AND EDA ANC UES ANC_CHKSM STD2 FLYWDIS 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 2 RW7 B5 RW6 B7 RW4 B3 RW3 B5 RW2 B7 ANC EDH ANC IDA ANC EDH ANC IDA ANC EDH ANC IDA TRS_INSERT STD1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 GS9020A 21 of 31 19922 - 3 TRS_BLANK STD0 ANC IDH RW7 B4 RW6 B6 RW4 B2 RW3 B4 RW2 B6 EDH_CHKSM ANC IDH 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 19922 - 3 22 of 31 RESERVED WORDS (INCOMING) ERRORED FIELD COUNTER AP CRC OUTGOING AP CRC INCOMING FF CRC OUTGOING FF CRC INCOMING OUTGOING ERROR FLAGS b23 b15 b7 RW1 B7 RW2 B5 RW3 B3 RW5 B7 RW6 B5 RW7 B3 16 17 18 19 20 21 22 23 b7 b15 b7 b15 b7 b15 b7 b15 15 14 13 12 11 10 9 8 7 AP UES 6 AP UES 4 FF UES FF UES 3 5 NO_EDH 2 INCOMING ERROR FLAGS F2 1 CONFIGURATION 7 ADDRESS READ Table TABLE 3: GS9020A Host Interface Read Table RW7 B2 RW6 B4 RW5 B6 RW3 B2 RW2 B4 RW1 B6 b6 b14 b22 b6 b14 b6 b14 b6 b14 b6 b14 AP IDA FF IDA AP IDA FF IDA EDH_CHKSM F1 6 0 RW6 B3 RW5 B5 RW4 B7 RW2 B3 RW1 B5 b5 b13 b21 b5 b13 b5 b13 b5 b13 b5 b13 AP IDH FF IDH AP IDH FF IDH TRS_ERR F0 5 0 RW6 B2 RW5 B4 RW4 B6 RW2 B2 RW1 B4 b4 b12 b20 b4 b12 b4 b12 b4 b12 b4 b12 AP EDA FF EDA AP EDA FF EDA FFV S 4 0 RW7 B7 RW5 B3 RW4 B5 RW3 B7 RW1 B3 b3 b11 b19 b3 b11 b3 b11 b3 b11 b3 b11 AP EDH FF EDH AP EDH FF EDH APV STD3 3 0 RW7 B6 RW5 B2 RW4 B4 RW3 B6 RW1 B2 b2 b10 b18 b2 b10 b2 b10 b2 b10 b2 b10 ANC EDA ANC UES ANC EDA ANC UES 0 STD2 2 0 RW7 B5 RW6 B7 RW4 B3 RW3 B5 RW2 B7 b1 b9 b17 b1 b9 b1 b9 b1 b9 b1 b9 ANC EDH ANC IDA ANC EDH ANC IDA 0 STD1 1 GS9020A 0 RW7 B4 RW6 B6 RW4 B2 RW3 B4 RW2 B6 b0 b8 b16 b0 b8 b0 b8 b0 b8 b0 b8 0 ANC IDH 0 ANC IDH 0 STD0 0 SDI CLOCK SYNCHRONOUS INPUTS VALID GS9020A t2 SERIAL DATA PCLKOUT tSS t1 tSH Fig. 1 Serial Data Input Setup & Hold Times Fig. 2 Input Setup & Hold Times (Synchronous Inputs) VDD, SDI VDD, SDI RPULLUP SYNCHRONOUS OUTPUTS DATA VALID RPULLUP SDI SDI tOS tOH PCLKOUT tOD Fig. 3 Output Delay & Hold Times (Synchronous Outputs) VDD Fig. 4 Serial Data & Clock Input Circuit VDD VDD VDD GS9025A GS9020A SDO SDO VDD, SDI SDI SDI VDD, SDI SCO SCO VDD, SCI SCI SCI VDD, SCI SDO Fig. 5 Interfacing the GS9020A to the GS9025A SDO Fig. 6 Serial Data Output Circuit VDD GS9025A GS9028 GS9020A VDD, SDI SDO SDO SCO SCO Z0 SDI SDO SDI SDO + VDD, SDI VDIFF OUT 2Z 0 VDD, SCI SCI SCI SDO VDD, SCI VDIFF OUT = SDO x 2Z0 SDOMODE SDI SDO GS9025 SDI Fig. 7 Interfacing the GS9020A to the GS9028 23 of 31 19922 - 3 tOS tOH tOD tOS PCLKOUT 3FF GS9020A DOUT [9:0] 000 000 3FF EAV 000 000 SAV F [2:0] V H Fig. 8a FVH Timing for Component Video tOH tOS tOD tOS PCLKOUT DOUT [9:0] 3FF 000 000 000 TRS-ID F [2:0] H Fig. 8b F and H Timing for Composite Video PCLKOUT DOUT[9:0] 3FF 000 000 EAV ID 3FF 000 000 SAV ID FIFO_RESET Fig. 9a FIFO_RESET Pulse Timing for Component Signals (FIFOE/S = 1) PCLKOUT DOUT[9:0] 3FF 000 000 EAV ID 3FF 000 000 FIFO_RESET Fig. 9b FIFO_RESET Pulse Timing for Component Signals (FIFOE/S = 0) 24 of 31 19922 - 3 SAV ID PCLKOUT DOUT[9:0] 3FF 000 000 000 TRS ID FIFO_RESET GS9020A Fig. 9c FIFO_RESET Pulse Timing for Composite Signals (FIFOE/S = 0 or 1) PCLKOUT DOUT[9:0] 000 3FF 3FF DID UDW UDW CS UDW CS ANC_DATA Fig. 10a ANC_DATA Timing for Component Signals PCLKOUT DOUT[9:0] 3CF DBN DID DC UDW ANC_DATA Fig. 10b ANC_DATA Timing for Composite Signals SDI/SDI DOUT[9:0] EDH EDH E D H E D H INTERRUPT TRANSITION POINT UNKNOWN TRANSITION POINT UNKNOWN Fig. 11 INTERRUPT Timing 25 of 31 19922 - 3 READ CYCLE { { WRITE CYCLE F_R//W GS9020A FF AP ANC S11 t0 t1 t2 t3 t4 t5 t6 t7 t8 XX 00 01 10 11 00 01 10 11 XX FL[4:0] XX FF AP ANC S11 PCLKOUT S[1:0] Fig. 12a Flag Port READ/WRITE Timing F_R/W F_R/W tFEN FL [4:0] FL [4:0] tFDIS PCLKOUT PCLKOUT Fig. 12b Flag Port Disable Time Fig. 12c Flag Port Enable Time PCLKOUT F_R/W X FLAGMAP FL[4:0] XX0 XX 1 XX 2 AP FF ANC ANC AP FF ANC S[1:0] XX 0 XX 1 XX 2 01 00 10 10 01 00 10 tFEN Flags held at ANC between EDH packets Double clocking Fig. 12d Flag Port Timing in FLAG MAP MODE GS9020A or GS9021A CRC_MODE = 0 R/T = 1 (GS9021A) GS9021A PROCESSING WHICH DOES NOT AFFECT THE EDH PACKET CRC_MODE = 1 Fig. 13a Example of CRC_MODE Implementation 26 of 31 19922 - 3 GS9020A or GS9021A CRC_MODE = 0 FLAG MAP = 1 F_R/W = 1 R/T = 1 (GS9021A) GS9021A PROCESSING CORRUPTS EDH PACKET GS9020A FL [4:0] S [1:0] FLAG MAP = 0 F_R/W = 0 7 Fig. 13b Example of FLAG_MAP Mode Implementation tHS tHH P [7:0] A/D R/W CS Fig. 14a HOSTIF Parallel Port Input Setup & Hold Times tHEN P[7:0] tHDIS GS9020A DRIVING R/W CS Fig. 14b HOSTIF Parallel Port Output Enable & Disable Times 27 of 31 19922 - 3 READ CYCLE { P[7:0] { WRITE CYCLE DATA IN ADDRESS ADDRESS DATA DATA GS9020A R/W A/D CS t0 t1 t4 t3 t2 Fig. 14c HOSTIF Parallel Port READ/WRITE Cycles FIELD 0 SDI/SDI FIELD 1 FIELD 2 EDH F0 EDH F1 t0 E D H F1 E D H F0 DOUT[9:0] 2 LINES VALID TIME TO READ/WRITE EDH INFORMATION TO/FROM GS9020 Fig. 15 Host Interface READ/WRITE Timing tMAX = 25s VDD VDD INTERNAL POWER on RESET CELL 5V 2k 0V t RESET INTERNAL RESET SIGNAL RESET PIN ~1.4 mS RESET Manual Reset Switch (Optional) 5V 1uF 20k tRESET 0V Fig. 16a Reset Circuitry Fig. 16b Acceptable external reset circuit when a master reset is not available 28 of 31 19922 - 3 t IN2 J3 L7 15nH R19 75 Z0 = 75 C1 10 R43 39 R21 75 75 R20 C2 100n R24 2k VCC VCC VCC C19 100pF C14 10n C17 10n C13 10n C11 10n C9 10n VCC C21 10n AGC- CD-ADJ VEE_EQA VCC_EQA SDI SDI VEE_EQD VCC_EQD VCC75_2 DDI SMPTE VCC VCC 11K Q4 R101 LED23 R99 150 C29 100n VCC DDI C22 100n 11 10 9 8 7 6 5 4 3 2 1 C28 10 4.7n 1k8 R31 3p3 C24 11K R100 C10 GS9025A 15n C26 16 LFS 17 LF- VDD VEE1 VCC VCC C43 100n C23 100n 100n C20 VCC VEE 33 32 SDO 31 SDO 30 VEE 29 SCO 28 SCO 27 VEE 26 A/M 25 SS0 24 SS1 23 SS2 C8 10n SS2 SS1 SS0 A/M 1 2 2 D2 1 VDD Z0 = 75 Z0 = 75 D1 VDD 10n C41 10n C40 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 P5 P6 P7 CRC_MODE FIFOE/S HOSTIF_MODE GND VDD VDDSCI SCI SCI VDDSCI VDDSDI SDI SDI VDDSDI VDD GND GND VDD ANC_DATA 36 VDD VDD VDD VDD GS9020A 10n C25 Fig. 17 GS9025A - GS9020A Schematic Diagram (basic operation schematic) 18 VCC75_1 44 NC.(OEM) 43 SMPTE 42 12 AGC+ 13 V CC LOCK A/D 41 SSI-CD 40 39 14 VEE 15 LF+ 38 COSC 37 VEE RVCO19 CLK_EN 20 R25 RVCO+ 35 VCC 34 VEE VCC 22 CBG 21 365 VDD VDD VDD VDD CLIP_TRS VBLANKS/L 73 TRS_ERROR ANC_DATA 80 TRS_ERR 79 78 21 SCL/P4 22 SDA/P3 77 ANC_CHKSM 23 A2/P2 24 A1/P1 75 SDOMODE 76 BLANK_EN 25 A0/P0 26 R/W 74 BYPASS_EDH GND 30 GND 31 RESET 32 NC VCC VDD 29 VBLANKS/L 27 A/D 28 CS 72 SGND 71 SDO 70 SDO 69 SVDD VDD 68 VDD 67 GND 33 STD2 34 STD1 65 F2 VCC D3 54 D2 53 D5 56 D4 55 D7 58 D6 57 D8 59 D9 60 D1 52 51 VDD 50 GND 49 D0 48 PCLKOUT 47 FIFO_RESET 46 NO_EDH 45 FLYWDIS 44 INTERRUPT 43 F_R/W 42 S0 41 S1 37 FL3 38 FL2 66 FLAG_MAP 35 STD0 36 FL4 64 F1 63 F0 61 V 62 H 39 FL1 40 FL0 GS9020A 29 of 31 19922 - 3 VDD VDD CLK D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 10n C12 VDD OUTPUTS & CLOCK VIDEO DATA R6 VDD C42 VDD R4 50 100n C28 10 C29 100n VCC VEE R7 50 RSET SDI Z0 = 50 R99 150 C5 C3 100n 1 R VEE SDI VDD VCC GS9020A 59 GS9028 SDO 7 SDO R 7 LED23 C26 1k8 15n 10n 20 100n C23 C43 100n 100n V H 61 V F1 F2 F0 62 H 63 F0 64 F1 FLAG_MAP 66 65 F2 67 INTERRUPT CRC_MODE P7 F_R/W P6 S0 P5 VDD I2C INTERFACE C25 10n 30 of 31 GND FLYWDIS Fig. 18 GS9025A - GS9020A - GS9028 Schematic Diagram (advanced operation schematic) 19922 - 3 FLAG_MAP 68 VDD SVDD 69 70 SDO SDO VDD VBLANKS/L 71 72 SGND SDOMODE BLANK_EN BYPASS_EDH 73 VBLANKS/L BYPASS_EDH 74 75 SDOMODE CLIP_TRS ANC_CHKSM 76 BLANK_EN 77 ANC_CHKSM 78 CLIP_TRS FIFOE/S S1 FL0 19 NO_EDH 39 FL1 40 FL0 C41 HOSTIF_MODE FL1 C20 18 GND FL2 VCC FIFO_RESET 37 FL3 38 FL2 16 17 3p3 R31 15 PCLKOUT VDD FL3 1 D0 FL4 SS2 14 GND VDDSCI 35 STD0 36 FL4 23 13 GS9020A SCI STD0 24 2 SS1 D2 VDD SCI STD1 SS0 D1 52 51 VDDSCI 33 STD2 34 STD1 VDD 25 12 VDD VDDSDI 31 RESET 32 NC C24 A/M D3 54 D2 53 SDI STD2 C22 100n 26 D5 56 D4 55 29 V DD 30 GND VCC C21 10n 11 27 D7 58 D6 57 SDI 27 A/D 28 CS VCC 10 D9 60 D8 59 VDDSDI SCL CC C19 100pF Z0 = 75 28 VDD FVH INDICATION VDD 25 A0/P0 26 R/W SS2 9 29 VCC SS1 AGCCBG CD-ADJ 8 30 GND A0 SS0 7 Z0 = 75 31 GND A1 VEE_EQA 5 VDD 23 A2/P2 24 A1/P1 A/M 4 6 VDD A/D 41 SSI-CD 40 39 LOCK 38 COSC 37 VEE 36 CLK_EN 35 VCC 34 VEE VEE VCC_EQA 12 AGC+ 13 V 11 SDI 22 10 SCO 21 9 GS9025A SDI 365 17 0n 8 SCO RVCO- 7 VCC VEE_EQD RVCO+ 6 VEE 20 5 SDO R25 11 0n VCC75_2 VCC_EQD VEE 4 VEE 33 32 SDO 19 3 2 3 DDI 18 VCC DDI 16 LFS 17 LF- 2 14 VEE 15 LF+ 1 VCC75_1 44 NC.(OEM) 43 SMPTE 42 9 0n 1 A2 10n 21 SCL/P4 22 SDA/P3 C40 1 SMPTE SDA D1 4.7n VDD C8 10n C10 VCC 2 ANC_DATA 80 TRS_ERR 79 VDD 11K VCC VCC ANC_DATA VCC R100 11K VDD Q4 R101 TRS_ERROR USER SELECTED OPTIONS 50 49 48 47 46 45 44 43 42 41 PACKAGE DIMENSIONS 16.00 0.20 14.00 0.10 13 TYP 1 GS9020A 80 0.20 MIN 0.08/0.20 RADIUS 16.00 0.20 7 MAX 0 MIN 14.00 0.10 13 TYP 0.60 0.15 0.08 MIN RADIUS 1.0 REF Dimensions in millimetres 1.40 0.05 80 pin LQFP 1.60 MAX 0.30 0.08 0.65 BSC CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION REVISION NOTES: DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. Added lead-free and green information. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. (c) Copyright November 1997 Gennum Corporation. All rights reserved. Printed in Canada. 31 of 31 19922 - 3 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Semtech: GS9020ACTVE3 GS9020ACFVE3