S27KL0641/S27KS0641 S70KL1281/S70KS1281 3.0 V/1.8 V, 64 Mb (8 MB)/128 Mb (16 MB), HyperRAMTM Self-Refresh DRAM Distinctive Characteristics HyperRAMTM Low Signal Count Interface 3.0 V I/O, 11 bus signals Single ended clock (CK) 1.8 V I/O, 12 bus signals Differential clock (CK, CK#) Chip Select (CS#) 8-bit data bus (DQ[7:0]) Read-Write Data Strobe (RWDS) Bidirectional Data Strobe / Mask Output at the start of all transactions to indicate refresh latency Output during read transactions as Read Data Strobe Input during write transactions as Write Data Mask RWDS DCARS Timing During read transactions RWDS is offset by a second clock, phase shifted from CK The Phase Shifted Clock is used to move the RWDS transition edge within the read data eye High Performance Up to 333 MBps Double-Data Rate (DDR) - two data transfers per clock 166 MHz clock rate (333 MBps) at 1.8 V VCC 100 MHz clock rate (200 MBps) at 3.0 V VCC Sequential burst transactions Configurable Burst Characteristics Wrapped burst lengths: * 16 bytes (8 clocks) * 32 bytes (16 clocks) * 64 bytes (32 clocks) * 128 bytes (64 clocks) Linear burst Hybrid option - one wrapped burst followed by linear burst Wrapped or linear burst type selected in each transaction Configurable output drive strength Low Power Modes Deep Power Down Package 24-ball FBGA Performance Summary Read Transaction Timings Maximum Clock Rate at 1.8 V VCC/VCCQ 166 MHz Maximum Clock Rate at 3.0 V VCC/VCCQ 100 MHz Maximum Access Time, (tACC at 166 MHz) 36 ns Maximum CS# Access Time to first word at 166 MHz (excluding refresh latency) 56 ns Maximum Current Consumption 64 MB 128 MB 60 mA 72 mA Power On Reset 50 mA 100 mA Standby (CS# = HIGH, 3.0 V, 105 C) 300 A 600 A Deep Power Down (CS# = HIGH, 3.0 V, 105 C) 40 A N/A Standby (CS# = HIGH, 1.8 V, 105 C) 300 A 600 A Deep Power Down (CS# = HIGH, 1.8 V, 105 C) 20 A N/A Burst Read or Write (linear burst at 166 MHz, 1.8 V) Cypress Semiconductor Corporation Document Number: 001-97964 Rev. *L * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised July 31, 2018 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Logic Block Diagrams X Decoders Block Diagram -- 64 Mb CS# CK/CK# Memory RWDS Control Logic I/O Y Decoders DQ[7:0] Data Latch RESET# Data Path Block Diagram -- 128 Mb CS# CS# CK/CK# CK/CK# RWDS RWDS X Decoders HyperRAM 1 I/O DQ[7:0] Control Logic Memory Y Decoders DQ[7:0] Data Latch RESET# Data Path X Decoders HyperRAM 2 CS# CK/CK# Memory RWDS I/O DQ[7:0] RESET# Control Logic Y Decoders Data Latch RESET# Data Path Document Number: 001-97964 Rev. *L Page 2 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 HyperRAM Block Diagram HyperRAM Connections, Including Optional Signals Master VCC VCCQ Slave 0 CS0# CK CK# DQ[7:0] CS# CK CK# DQ[7:0] RWDS RWDS VCC VCCQ CS1# RESET# RESET# 64 Mbit VSS VSSQ VSS VSSQ Slave 1 VCC VCCQ CS# CK CK# DQ[7:0] RWDS RESET# 64 Mbit VSS VSSQ Document Number: 001-97964 Rev. *L Page 3 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Contents 1. General Description..................................................... 5 2. Product Overview ........................................................ 8 3. Signal Descriptions ..................................................... 9 3.1 Input/Output Summary .......................................... 9 3.2 Command/Address Bit Assignments................... 10 3.3 Read Transactions .............................................. 14 3.4 Write Transactions with Initial Latency (Memory Core Write)........................................... 15 3.5 Write Transactions without Initial Latency (Register Write) ..................................... 17 4. Memory Space............................................................ 18 5. Register Space ........................................................... 18 5.1 Device Identification Registers ............................ 19 5.2 Register Space Access ....................................... 20 6. Interface States .......................................................... 26 6.1 Power Conservation Modes ................................ 27 7. Electrical Specifications............................................ 7.1 Absolute Maximum Ratings................................. 7.2 Latchup Characteristics....................................... 7.3 Operating Ranges ............................................... 7.4 DC Characteristics .............................................. 7.5 Power-Up Initialization......................................... 7.6 Power Down ........................................................ 7.7 Hardware Reset .................................................. 28 28 29 29 30 32 33 34 8. Timing Specifications................................................. 35 8.1 Key to Switching Waveforms ............................... 35 8.2 AC Test Conditions .............................................. 35 8.3 AC Characteristics ............................................... 36 9. Physical Interface ....................................................... 39 9.1 FBGA 24-Ball 5 x 5 Array Footprint...................... 39 9.2 Physical Diagrams ............................................... 40 10. DDR Center Aligned Read Strobe (DCARS) Functionality ............................................... 41 10.1 HyperRAM Products with DCARS Signal Descriptions .............................................. 41 10.2 HyperRAM Products with DCARS -- FBGA 24-ball, 5 x 5 Array Footprint ................ 42 10.3 HyperRAM Memory with DCARS Timing ............. 42 11. Ordering Information .................................................. 44 11.1 Ordering Part Number.......................................... 44 11.2 Valid Combinations .............................................. 45 11.3 Valid Combinations -- Automotive Grade / AEC-Q100.......................................................... 47 12. Revision History.......................................................... 49 Sales, Solutions, and Legal Information ...........................51 Worldwide Sales and Design Support ........................... 51 Products ........................................................................ 51 PSoC(R) Solutions .......................................................... 51 Cypress Developer Community ..................................... 51 Technical Support ......................................................... 51 Document Number: 001-97964 Rev. *L Page 4 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 1. General Description The Cypress(R) 64-Mb HyperRAMTM device is a high-speed CMOS, self-refresh Dynamic RAM (DRAM), with a HyperBus interface. The Cypress 128-Mb HyperRAM is a dual-die stack of 64-Mb HyperRAM devices in a single package. The Random Access Memory (RAM) array uses dynamic cells that require periodic refresh. Refresh control logic within the device manages the refresh operations on the RAM array when the memory is not being actively read or written by the HyperBus interface master (host). Since the host is not required to manage any refresh operations, the DRAM array appears to the host as though the memory uses static cells that retain data without refresh. Hence, the memory can also be described as Pseudo Static RAM (PSRAM). Because the DRAM cells cannot be refreshed during a read or write transaction, there is a requirement that the host not perform read or write burst transfers that are long enough to block the necessary internal logic refresh operations when they are needed. The host is required to limit the duration of transactions and allow additional initial access latency, at the beginning of a new transaction, if the memory indicates a refresh operation is needed. HyperBus is a low-signal-count, Double Data Rate (DDR) interface that achieves high-speed read and write throughput. The DDR protocol transfers two data bytes per clock cycle on the DQ input/output signals. A read or write transaction on HyperBus consists of a series of 16-bit wide, one clock cycle data transfers at the internal HyperRAM core with two corresponding 8-bit wide, one-half-clock-cycle data transfers on the DQ signals. All inputs and outputs are LV-CMOS compatible. Ordering Part Number (OPN) device versions are available for core (VCC) and IO buffer (VCCQ) supplies of either 1.8 V or 3.0 V (nominal). Command, address, and data information is transferred over the eight HyperBus DQ[7:0] signals. The clock is used for information capture by a HyperBus slave device when receiving command, address, or data on the DQ signals. Command or Address values are center aligned with clock transitions. Every transaction begins with the assertion of CS# and Command-Address (CA) signals, followed by the start of clock transitions to transfer six CA bytes, followed by initial access latency and either read or write data transfers, until CS# is deasserted. Figure 1. Read Transaction, Single Initial Latency Count CS# tRWR =Read Write Recovery t ACC = Access CK#,CK Latency Count High = 2x Latency Count Low = 1x Latency Count RWDS RWDS and Data are edge aligned 47:40 DQ[7:0] 39:32 31:24 23:16 15:8 7:0 Command-Address Host drives DQ[7:0] and Memory drives RWDS Dn A Dn B Dn+1 A Dn+1 B Memory drives DQ[7:0] and RWDS The Read/Write Data Strobe (RWDS) is a bidirectional signal that indicates: when data will start to transfer from a HyperRAM device to the master device in read transactions (initial read latency) when data is being transferred from a HyperRAM device to the master device during read transactions (as a source synchronous read data strobe) when data may start to transfer from the master device to a HyperRAM device in write transactions (initial write latency) data masking during write data transfers During the CA transfer portion of a read or write transaction, RWDS acts as an output from a HyperRAM device to indicate whether additional initial access latency is needed in the transaction. During read data transfers, RWDS is a read data strobe with data values edge aligned with the transitions of RWDS. Document Number: 001-97964 Rev. *L Page 5 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Figure 2. Read Transaction, Additional Latency Count CS# tRWR=Read Write Recovery Additional Latency tACC = Access Latency Count 1 Latency Count 2 CK#, CK RWDS DQ[7:0] High = 2x Latency Count Low = 1x Latency Count 47:40 39:32 31:24 23:16 15:8 RWDS and Data are edge aligned Dn A 7:0 Command-Address Dn B Dn+1 Dn+1 A B Memory drives DQ[7:0] and RWDS Host drives DQ[7:0] and Memory drives RWDS During write data transfers, RWDS indicates whether each data byte transfer is masked with RWDS HIGH (invalid and prevented from changing the byte location in a memory) or not masked with RWDS LOW (valid and written to a memory). Data masking may be used by the host to byte align write data within a memory or to enable merging of multiple non-word aligned writes in a single burst write. During write transactions, data is center aligned with clock transitions. Figure 3. Write Transaction, Single Initial Latency Count CS# tRWR =Read Write Recovery tACC = Access CK#, CK CK and Data are center aligned Latency Count RWDS DQ[7:0] High = 2x Latency Count Low = 1x Latency Count 47:40 39:32 31:24 23:16 15:8 7:0 Command-Address Host drives DQ[7:0] and Memory drives RWDS Dn A Dn B Dn+1 A Dn+1 B Host drives DQ[7:0] and RWDS Read and write transactions are burst oriented, transferring the next sequential word during each clock cycle. Each individual read or write transaction can use either a wrapped or linear burst sequence. Document Number: 001-97964 Rev. *L Page 6 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Figure 4. Linear Versus Wrapped Burst Sequence 16 word group alignment boundaries Linear Burst 4h 5h 6h 7h 8h 9h Ah Bh Ch Dh Eh Fh 10h 11h 12h 13h Initial address = 4h Wrapped Burst 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h Ah Bh Ch Dh Eh Fh During wrapped transactions, accesses start at a selected location and continue to the end of a configured word group aligned boundary, then wrap to the beginning location in the group, then continue back to the starting location. Wrapped bursts are generally used for critical word first cache line fill read transactions. During linear transactions, accesses start at a selected location and continue in a sequential manner until the transaction is terminated when CS# returns HIGH. Linear transactions are generally used for large contiguous data transfers such as graphic images. Since each transaction command selects the type of burst sequence for that transaction, wrapped and linear bursts transactions can be dynamically intermixed as needed. Document Number: 001-97964 Rev. *L Page 7 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 2. Product Overview The 64-Mb and 128-Mb HyperRAM devices are 1.8 V or 3.0 V core and I/O, synchronous self-refresh Dynamic RAM (DRAM). The HyperRAM device provides a HyperBus slave interface to the host system. HyperBus has an 8-bit (1 byte) wide DDR data bus and uses only word-wide (16-bit data) address boundaries. Read transactions provide 16 bits of data during each clock cycle (8 bits on both clock edges). Write transactions take 16 bits of data from each clock cycle (8 bits on each clock edge). Figure 5. HyperRAM Interface RESET# CS# CK CK# VCC VCCQ DQ[7:0] RWDS VSS VSSQ Read and write transactions require two clock cycles to define the target row address and burst type, then an initial access latency of tACC. During the Command-Address (CA) part of a transaction, the memory will indicate whether an additional latency for a required refresh time (tRFH) is added to the initial latency; by driving the RWDS signal to the HIGH state. During the CA period the third clock cycle will specify the target word address within the target row. During a read (or write) transaction, after the initial data value has been output (or input), additional data can be read from (or written to) the row on subsequent clock cycles in either a wrapped or linear sequence. When configured in linear burst mode, the device will automatically fetch the next sequential row from the memory array to support a continuous linear burst. Simultaneously accessing the next row in the array while the read or write data transfer is in progress, allows for a linear sequential burst operation that can provide a sustained data rate of 333 MBps (1 byte (8 bit data bus) * 2 (data clock edges) * 166 MHz = 333 MBps). Document Number: 001-97964 Rev. *L Page 8 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 3. Signal Descriptions 3.1 Input/Output Summary HyperRAM signals are shown in Table 1. Active LOW signal names have a hash symbol (#) suffix. Table 1. I/O Summary Symbol Type Description Master Output, Slave Input Chip Select. Bus transactions are initiated with a HIGH to LOW transition. Bus transactions are terminated with a LOW to HIGH transition. The master device has a separate CS# for each slave. CK, CK# Master Output, Slave Input Differential Clock. Command, address, and data information is output with respect to the crossing of the CK and CK# signals. Differential clock is used on 1.8 V I/O devices. Single Ended Clock. CK# is not used on 3.0 V devices, only a single ended CK is used. The clock is not required to be free-running. DQ[7:0] Input/Output Data Input/Output. Command, Address, and Data information is transferred on these signals during Read and Write transactions. RWDS Input/Output Read Write Data Strobe. During the Command/Address portion of all bus transactions RWDS is a slave output and indicates whether additional initial latency is required. Slave output during read data transfer, data is edge aligned with RWDS. Slave input during data transfer in write transactions to function as a data mask. (HIGH = additional latency, LOW = no additional latency). RESET# Master Output, Slave Input, Internal Pull-up Hardware RESET. When LOW the slave device will self initialize and return to the Standby state. RWDS and DQ[7:0] are placed into the HI-Z state when RESET# is LOW. The slave RESET# input includes a weak pull-up, if RESET# is left unconnected it will be pulled up to the HIGH state. CS# VCC Power Supply Power. VCCQ Power Supply Input/Output Power. VSS Power Supply Ground. VSSQ Power Supply Input/Output Ground. RFU No Connect Reserved for Future Use. May or may not be connected internally, the signal/ball location should be left unconnected and unused by PCB routing channel for future compatibility. The signal/ball may be used by a signal in the future. Document Number: 001-97964 Rev. *L Page 9 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 3.2 Command/Address Bit Assignments All HyperRAM bus transactions can be classified as either read or write. A bus transaction is started with CS# going LOW with clock in idle state (CK=LOW and CK#=HIGH). The first three clock cycles transfer three words of Command/Address (CA0, CA1, CA2) information to define the transaction characteristics. The Command/Address words are presented with DDR timing, using the first six clock edges. The following characteristics are defined by the Command/Address information: Read or Write transaction Address Space: memory array space or register space Register space is used to access Device Identification (ID) registers and Configuration Registers (CR) that identify the device characteristics and determine the slave specific behavior of read and write transfers on the HyperBus interface. Whether a transaction will use a linear or wrapped burst sequence. The target row (and half-page) address (upper order address) The target column (word within half-page) address (lower order address) Figure 6. Command-Address Sequence[1, 2, 3] CS# CK , CK# DQ[7:0] CA0[47:40] CA0[39:32] CA1[31:24] CA1[23:16] CA2[15:8] CA2[7:0] Table 2. Command-Address Bit Assignment to DQ Signals Signal CA0[47:40] CA0[39:32] CA1[31:24] CA1[23:16] CA2[15:8] CA2[7:0] DQ[7] CA[47] CA[39] CA[31] CA[23] CA[15] CA[7] DQ[6] CA[46] CA[38] CA[30] CA[22] CA[14] CA[6] DQ[5] CA[45] CA[37] CA[29] CA[21] CA[13] CA[5] DQ[4] CA[44] CA[36] CA[28] CA[20] CA[12] CA[4] DQ[3] CA[43] CA[35] CA[27] CA[19] CA[11] CA[3] DQ[2] CA[42] CA[34] CA[26] CA[18] CA[10] CA[2] DQ[1] CA[41] CA[33] CA[25] CA[17] CA[9] CA[1] DQ[0] CA[40] CA[32] CA[24] CA[16] CA[8] CA[0] Notes 1. Figure shows the initial three clock cycles of all transactions on the HyperBus. 2. CK# of differential clock is shown as dashed line waveform. 3. Command-Address information is "center aligned" with the clock during both Read and Write transactions. Document Number: 001-97964 Rev. *L Page 10 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 3. Command/Address Bit Assignments[4, 5, 6, 7, 8] CA Bit# Bit Name 47 R/W# Bit Function Identifies the transaction as a read or write. R/W# = 1 indicates a Read transaction R/W# = 0 indicates a Write transaction Indicates whether the read or write transaction accesses the memory or register space. Address Space AS = 0 indicates memory space (AS) AS = 1 indicates the register space The register space is used to access device ID and Configuration registers. 46 45 Burst Type 44-16 Indicates whether the burst will be linear or wrapped. Burst Type = 0 indicates wrapped burst Burst Type = 1 indicates linear burst Row & Upper Column component of the target address: System word address bits A31-A3 Row & Upper Any upper Row address bits not used by a particular device density should be set to 0 by the Column Address host controller master interface. The size of Rows and therefore the address bit boundary between Row and Column address is slave device dependent. 15-3 Reserved 2-0 Lower Column Address Reserved for future column address expansion. Reserved bits are don't care in current HyperBus devices but should be set to 0 by the host controller master interface for future compatibility. Lower Column component of the target address: System word address bits A2-0 selecting the starting word within a half-page. Notes 4. A Row is a group of words relevant to the internal memory array structure and additional latency may be inserted by RWDS when crossing Row boundaries - this is device dependent behavior, refer to each HyperBus device data sheet for additional information. Also, the number of Rows may be used in the calculation of a distributed refresh interval for HyperRAM memory. 5. A Page is a 16-word (32-byte) length and aligned unit of device internal read or write access and additional latency may be inserted by RWDS when crossing Page boundaries - this is device dependent behavior, refer to each HyperBus device data sheet for additional information. 6. The Column address selects the burst transaction starting word location within a Row. The Column address is split into an upper and lower portion. The upper portion selects an 8-word (16-byte) Half-page and the lower portion selects the word within a Half-page where a read or write transaction burst starts. 7. The initial read access time starts when the Row and Upper Column (Half-page) address bits are captured by a slave interface. Continuous linear read burst is enabled by memory devices internally interleaving access to 16 byte half-pages. 8. HyperBus protocol address space limit, assuming: 29 Row &Upper Column address bits 3 Lower Column address bits Each address selects a word wide (16 bit = 2 byte) data value 29 + 3 = 32 address bits = 4G addresses supporting 8Gbyte (64Gbit) maximum address space Future expansion of the column address can allow for 29 Row &Upper Column + 16 Lower Column address bits = 35 Tera-word = 70 Tera-byte address space. Figure 7. Data Placement During a Read Transaction[9, 10, 11, 12, 13] CS# CK , CK# RWDS DQ[7:0] Dn A Dn B Dn+1 A Dn+1 B Dn+2 A Notes 9. Figure shows a portion of a Read transaction on the HyperBus. CK# of differential clock is shown as dashed line waveform. 10. Data is "edge aligned" with the RWDS serving as a read data strobe during read transactions. 11. Data is always transferred in full word increments (word granularity transfers). 12. Word address increments in each clock cycle. Byte A is between RWDS rising and falling edges and is followed by byte B between RWDS falling and rising edges, of each word. 13. Data bits in each byte are always in high to low order with bit 7 on DQ7 and bit 0 on DQ0. Document Number: 001-97964 Rev. *L Page 11 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 4. Data Bit Placement During Read or Write Transaction Address Space Byte Order Byte Position A Big-end ian B Memory A Little-en dian B Word Data Bit DQ 15 7 14 6 13 5 12 4 11 3 10 2 9 1 8 0 7 7 6 6 5 5 4 4 3 3 2 2 1 1 0 0 7 7 6 6 5 5 4 4 3 3 2 2 1 1 0 0 15 7 14 6 13 5 12 4 11 3 10 2 9 1 8 0 Document Number: 001-97964 Rev. *L Bit Order When data is being accessed in memory space: The first byte of each word read or written is the "A" byte and the second is the "B" byte. The bits of the word within the A and B bytes depend on how the data was written. If the word lower address bits 7-0 are written in the A byte position and bits 15-8 are written into the B byte position, or vice versa, they will be read back in the same order. So, memory space can be stored and read in either little-endian or big-endian order. Page 12 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 4. Data Bit Placement During Read or Write Transaction (Continued) Address Space Byte Order Byte Position A Register Big-end ian B Word Data Bit DQ 15 7 14 6 13 5 12 4 11 3 10 2 9 1 8 0 7 7 6 6 5 5 4 4 3 3 2 2 1 1 0 0 Bit Order When data is being accessed in register space: During a Read transaction on the HyperBus two bytes are transferred on each clock cycle. The upper order byte A (Word[15:8]) is transferred between the rising and falling edges of RWDS (edge aligned). The lower order byte B (Word[7:0]) is transferred between the falling and rising edges of RWDS. During a write, the upper order byte A (Word[15:8]) is transferred on the CK rising edge and the lower order byte B (Word[7:0]) is transferred on the CK falling edge. So, register space is always read and written in Big-endian order because registers have device dependent fixed bit location and meaning definitions. Figure 8. Data Placement During a Write Transaction[14, 15, 16, 17] CS# CK , CK# RWDS DQ[7:0] Dn A Dn B Dn+1 A Dn+1 B Dn+2 A Notes 14. Figure shows a portion of a Write transaction on the HyperBus. 15. Data is "center aligned" with the clock during a Write transaction. 16. RWDS functions as a data mask during write data transfers with initial latency. Masking of the first and last byte is shown to illustrate an unaligned 3 byte write of data. 17. RWDS is not driven by the master during write data transfers with zero initial latency. Full data words are always written in this case. RWDS may be driven LOW or left HI-Z by the slave in this case. Document Number: 001-97964 Rev. *L Page 13 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 3.3 Read Transactions The HyperBus master begins a transaction by driving CS# LOW while clock is idle. Then the clock begins toggling while Command-Address CA words are transfered. In CA0, CA[47] = 1 indicates that a Read transaction is to be performed. CA[46] = 0 indicates the memory space is being read or CA[46] = 1 indicates the register space is being read. CA[45] indicates the burst type (wrapped or linear). Read transactions can begin the internal array access as soon as the row and upper column address has been presented in CA0 and CA1 (CA[47:16]). CA2 (CA(15:0]) identifies the target Word address within the chosen row. However, some HyperBus devices may require a minimum time between the end of a prior transaction and the start of a new access. This time is referred to as Read-Write-Recovery time (tRWR). The master interface must start driving CS# LOW only at a time when the CA1 transfer will complete after tRWR is satisfied. The HyperBus master then continues clocking for a number of cycles defined by the latency count setting in configuration register 0. The initial latency count required for a particular clock frequency is based on RWDS. If RWDS is LOW during the CA cycles, one latency count is inserted. If RWDS is HIGH during the CA cycles, an additional latency count is inserted. Once these latency clocks have been completed the memory starts to simultaneously transition the Read-Write Data Strobe (RWDS) and output the target data. New data is output edge aligned with every transition of RWDS. Data will continue to be output as long as the host continues to transition the clock while CS# is LOW. However, the HyperRAM device may stop RWDS transitions with RWDS LOW, between the delivery of words, in order to insert latency between words when crossing memory array boundaries. Wrapped bursts will continue to wrap within the burst length and linear burst will output data in a sequential manner across row boundaries. When a linear burst read reaches the last address in the array, continuing the burst beyond the last address will provide undefined data. Read transfers can be ended at any time by bringing CS# HIGH when the clock is idle. The clock is not required to be free-running. The clock may remain idle while CS# is HIGH. Figure 9. Read Transaction with Additional Initial Latency[18, 19, 20, 21, 22, 23, 24, 25] CS# Additional Latency t RWR = Read Write Recovery tACC = Access CK# , CK RWDS High = 2x Latency Count Low = 1x Latency Count Latency Count 1 DQ[7:0] 47:40 39:32 31:24 23:16 15:8 7:0 Command-Address Latency Count 2 RWDS and Data are edge aligned Dn A Dn Dn+1 Dn+1 B A B Memory drives DQ[7:0] and RWDS Host drives DQ[7:0] and Memory drives RWDS Notes 18. Transactions are initiated with CS# falling while CK = LOW and CK# = HIGH. 19. CS# must return HIGH before a new transaction is initiated. 20. CK# is the complement of the CK signal. 3.0 V devices use a single ended clock (CK only), CK# is used with CK on1.8 V devices to provide a differential clock. CK# of a differential clock is shown as a dashed line waveform. 21. Read access array starts once CA[23:16] is captured. 22. The read latency is defined by the initial latency value in a configuration register. 23. In this read transaction example the initial latency count was set to four clocks. 24. In this read transaction a RWDS HIGH indication during CA delays output of target data by an additional four clocks. 25. The memory device drives RWDS during read transactions. Document Number: 001-97964 Rev. *L Page 14 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Figure 3.1 Read Transaction Without Additional Initial Latency[26] CS# t RWR =Read Write Recovery t ACC = Initial Acces s CK, CK# RWDS High = 2x Latency Count Low = 1x Latency Count RWDS and Data are edge aligned 4 cycle latency DQ[7:0] 47:40 39:32 31:24 23:16 15:8 7:0 Command-Address Host drives DQ[7:0] and Memory drives RWDS 3.4 Dn A Dn B Dn+1 A Dn+1 B Memory drives DQ[7:0] and RWDS Write Transactions with Initial Latency (Memory Core Write) The HyperBus master begins a transaction by driving CS# LOW while clock is idle. Then the clock begins toggling while Command-Address CA words are transfered. In CA0, CA[47] = 0 indicates that a Write transaction is to be performed. CA[46] = 0 indicates the memory space is being written. CA[45] indicates the burst type (wrapped or linear). Write transactions can begin the internal array access as soon as the row and upper column address has been presented in CA0 and CA1 (CA[47:16]). CA2 (CA(15:0]) identifies the target word address within the chosen row. However, some HyperBus devices may require a minimum time between the end of a prior transaction and the start of a new access. This time is referred to as Read-Write-Recovery time (tRWR). The master interface must start driving CS# LOW only at a time when the CA1 transfer will complete after tRWR is satisfied. The HyperBus master then continues clocking for a number of cycles defined by the latency count setting in configuration register 0. The initial latency count required for a particular clock frequency is based on RWDS. If RWDS is LOW during the CA cycles, one latency count is inserted. If RWDS is HIGH during the CA cycles, an additional latency count is inserted. Once these latency clocks have been completed the HyperBus master starts to output the target data. Write data is center aligned with the clock edges. The first byte of data in each word is captured by the memory on the rising edge of CK and the second byte is captured on the falling edge of CK. During the CA clock cycles, RWDS is driven by the memory. During the write data transfers, RWDS is driven by the host master interface as a data mask. When data is being written and RWDS is HIGH the byte will be masked and the array will not be altered. When data is being written and RWDS is LOW the data will be placed into the array. Because the master is driving RWDS during write data transfers, neither the master nor the HyperRAM device are able to indicate a need for latency within the data transfer portion of a write transaction. The acceptable write data burst length setting is also shown in configuration register 0. Data will continue to be transferred as long as the HyperBus master continues to transition the clock while CS# is LOW. Legacy format wrapped bursts will continue to wrap within the burst length. Hybrid wrap will wrap once then switch to linear burst starting at the next wrap boundary. Linear burst accepts data in a sequential manner across page boundaries. Write transfers can be ended at any time by bringing CS# HIGH when the clock is idle. When a linear burst write reaches the last address in the memory array space, continuing the burst will write to the beginning of the address range. The clock is not required to be free-running. The clock may remain idle while CS# is HIGH. Notes 26. RWDS is LOW during the CA cycles. In this Read Transaction there is a single initial latency count for read data access because, this read transaction does not begin at a time when additional latency is required by the slave. Document Number: 001-97964 Rev. *L Page 15 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Figure 10. Write Transaction with Additional Initial Latency[27, 28, 29, 30, 31, 32, 33] CS# Additional Latency t RWR = Read Write Recovery tACC = Initial Access CK, CK# RWDS DQ[7:0] High = 2x Latency Count Low = 1x Latency Count Latency Count 1 47:40 39:32 31:24 23:16 15:8 CK and Data are center aligned Latency Count 2 Dn A 7:0 Dn Dn+1 Dn+1 B B A Host drives DQ[7:0] and RWDS Command-Address Host drives DQ[7:0] and Memory drives RWDS Figure 11. Write Transaction Without Additional Initial Latency[27, 30, 32, 33, 34] CS# tRWR=Read Write Recovery tACC = Access CK# , CK RWDS High = 2x Latency Count Low = 1x Latency Count CK and Data are center aligned Latency Count DQ[7:0] 47:40 39:32 31:24 23:16 15:8 7:0 Command-Address Host drives DQ[7:0] and Memory drives RWDS Dn A Dn B Dn+1 A Dn+1 B Host drives DQ[7:0] and RWDS Notes 27. Transactions must be initiated with CK = LOW and CK# = HIGH. 28. CS# must return HIGH before a new transaction is initiated. 29. During Command-Address, RWDS is driven by the memory and indicates whether additional latency cycles are required. 30. In this example, RWDS indicates that additional initial latency cycles are required. 31. At the end of Command-Address cycles, the memory stops driving RWDS to allow the host HyperBus master to begin driving RWDS. The master must drive RWDS to a valid LOW before the end of the initial latency to provide a data mask preamble period to the slave. 32. During data transfer, RWDS is driven by the host to indicate which bytes of data should be either masked or loaded into the array. 33. The figure shows RWDS masking byte A0 and byte B1 to perform an unaligned word write to bytes B0 and A1. 34. In this example, RWDS indicates that there is no additional latency required. Document Number: 001-97964 Rev. *L Page 16 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 3.5 Write Transactions without Initial Latency (Register Write) A Write transaction starts with the first three clock cycles providing the Command/Address information indicating the transaction characteristics. CA0 may indicate that a Write transaction is to be performed and also indicates the address space and burst type (wrapped or linear). Writes without initial latency are used for register space writes. HyperRAM device write transactions with zero latency mean that the CA cycles are followed by write data transfers. Writes with zero initial latency, do not have a turn around period for RWDS. The HyperRAM device will always drive RWDS during the Command-Address period to indicate whether extended latency is required for a transaction that has initial latency. However, the RWDS is driven before the HyperRAM device has received the first byte of CA i.e. before the HyperRAM device knows whether the transaction is a read or write to register space. In the case of a write with zero latency, the RWDS state during the CA period does not affect the initial latency of zero. Since master write data immediately follows the Command-Address period in this case, the HyperRAM device may continue to drive RWDS LOW or may take RWDS to HI-Z during write data transfer. The master must not drive RWDS during Writes with zero latency. Writes with zero latency do not use RWDS as a data mask function. All bytes of write data are written (full word writes). The first byte of data in each word is presented on the rising edge of CK and the second byte is presented on the falling edge of CK. Write data is center aligned with the clock inputs. Write transfers can be ended at any time by bringing CS# HIGH when clock is idle. The clock is not required to be free-running. Figure 12. Write Operation without Initial Latency CS# CK, CK# RWDS DQ[7:0] Memory drives RWDS but master ignores it 47:40 39:32 31:24 23:16 15:8 7:0 Command-Address 15:8 7:0 Data Host drives DQ[7:0] with Command-Address and Write Data Document Number: 001-97964 Rev. *L Page 17 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 4. Memory Space When CA[46] is 0 a read or write transaction accesses the DRAM memory array. Table 5. Memory Space Address Map Unit Type Count System Word Address Bits CA Bits Dies within 128 Mb device 2 A22 35 Rows within 64 Mb device 8192 (Rows) A21 - A9 34 - 22 Row 1 (row) A8 - A3 21 - 16 Half-Page 8 (word addresses) A2 - A0 2-0 Notes CA 35 (A22) = 0, bottom die CA 35 (A22) = 1, top die 512 (word addresses) 1 kbytes 16 bytes 5. Register Space When CA[46] is 1 a read or write transaction accesses the Register Space. Table 6. Register Space Address Map[35] Register System Address -- -- -- 31-27 26-19 18-11 10-3 -- 2-0 CA Bits 47 46 45 44-40 39-32 31-24 23-16 15-8 7-0 Identification Register 0 (read only) C0h or E0h 00h 00h 00h 00h 00h Identification Register 1 (read only) C0h or E0h 00h 00h 00h 00h 01h Configuration Register 0 Read C0h or E0h 00h 01h 00h 00h 00h Configuration Register 0 Write 60h 00h 01h 00h 00h 00h Configuration Register 1 Read C0h or E0h 00h 01h 00h 00h 01h Configuration Register 1 Write 60h 00h 01h 00h 00h 01h Note 35. CA45 may be either 0 or 1 for either wrapped or linear read. CA45 must be 1 as only linear single word register writes are supported. Document Number: 001-97964 Rev. *L Page 18 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 5.1 Device Identification Registers There are two read only, non-volatile, word registers, that provide information on the device selected when CS# is LOW. The device information fields identify: Manufacturer Type Density Row address bit count Column address bit count Table 7. ID Register 0 Bit Assignments Bits Function 64 Mb 15-14 128 Mb 13 12-8 Reserved Row Address Bit Count Settings (Binary) Reserved Die Address: 00 = Die 1 01 = Die 2 0 - default 00000 - One Row address bit ... 11111 - Thirty-two row address bits 01100 - 64 Mb 01101 - 128 Mb 7-4 Column Address Bit Count 3-0 Manufacturer 0000 - One column address bit ... 1111 - Sixteen column address bits 0000 - Reserved 0001 - Cypress 0010 to 1111 - Reserved Table 8. ID Register 1 Bit Assignments 5.1.1 Bits Function 15-4 Reserved 3-0 Device Type Settings (Binary) 0000_0000_0000b (default) 0000 - HyperRAM 1.0 0001 to 1111 - Reserved Density and Row Boundaries The DRAM array size (density) of the device can be determined from the total number of system address bits used for the row and column addresses as indicated by the Row Address Bit Count and Column Address Bit Count fields in the ID0 register. For example: a 64-Mb HyperRAM device has 9 column address bits and 13 row address bits for a total of 22 word address bits = 222 = 4 Mwords = 8 MB. The 9 column address bits indicate that each row holds 29 = 512 words = 1 kbytes. The row address bit count indicates there are 8196 rows to be refreshed within each array refresh interval. The row count is used in calculating the refresh interval. Document Number: 001-97964 Rev. *L Page 19 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 5.2 Register Space Access Register default values are loaded upon power-up or hardware reset. The registers can be altered at any time while the device is in the standby state. Loading a register is accomplished with a single 16-bit word write transaction as shown in Figure 13. CA[47] is zero to indicate a write transaction, CA[46] is a one to indicate a register space write, CA[45] is a one to indicate a linear write, lower order bits in the CA field indicate the register address. Figure 13. Loading a Register[36, 37, 38, 39] CS# CK, CK# RWDS DQ[7:0] Memory drives RWDS with Refresh Indication 47:40 39:32 31:24 23:16 15:8 Command-Address 7:0 15:8 7:0 RD Host drives DQ[7:0] with Command-Address and Register Data Each register is written with a separate single word write transaction. Register write transactions have zero latency, the single word of data immediately follows the Command-Address. RWDS is not driven by the host during the write because RWDS is always driven by the memory during the CA cycles to indicate whether a memory array refresh is in progress. Because a register space write goes directly to a register, rather than the memory array, there is no initial write latency, related to an array refresh that may be in progress. In a register write, RWDS is also not used as a data mask because both bytes of a register are always written and never masked. Reserved register fields must be written with their default value. Writing reserved fields with other than default values may produce undefined results. Reading of a register is accomplished with a single 16 bit read transaction with CA[46]=1 to select register space. If more than one word is read, the same register value is repeated in each word read. The CA[45] burst type is "don't care" because only a single register value is read. The contents of the register is returned in the same manner as reading array data, with one or two latency counts, based on the state of RWDS during the Command-Address period. The latency count is defined in the Configuration Register 0 Read Latency field (CR0[7:4]). Note: It is recommended to configure all configuration registers in the 128 Mb dual-die stack identically. Notes 36. The host must not drive RWDS during a write to register space. 37. The RWDS signal is driven by the memory during the Command-Address period based on whether the memory array is being refreshed. This refresh indication does not affect the writing of register data. RWDS is driven immediately after CS# goes LOW, before CA[47:46] are received to indicate that the transaction is a write to register space, for which the RWDS refresh indication is not relevant. 38. The register value is always provided immediately after the CA value and is not delayed by a refresh latency. 39. The the RWDS signal returns to HI-Z after the Command-Address period. Register data is never masked. Both data bytes of the register data are loaded into the selected register. Document Number: 001-97964 Rev. *L Page 20 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 5.2.1 Configuration Register 0 Configuration Register 0 (CR0) is used to define the power mode and access protocol operating conditions for the HyperRAM device. Configurable characteristics include: Wrapped Burst Length (16, 32, 64, or 128-byte aligned and length data group) Wrapped Burst Type Legacy wrap (sequential access with wrap around within a selected length and aligned group) Hybrid wrap (Legacy wrap once then linear burst at start of the next sequential group) Initial Latency Variable Latency Whether an array read or write transaction will use fixed or variable latency. If fixed latency is selected the memory will always indicate a refresh latency and delay the read data transfer accordingly. If variable latency is selected, latency for a refresh is only added when a refresh is required at the same time a new transaction is starting. Output Drive Strength Deep Power Down Mode Table 9. Configuration Register 0 Bit Assignments CR0 Bit 15 Function Deep Power Down Enable (64 Mb) Reserved (128 Mb) 14-12 Drive Strength 11-8 Reserved 7-4 3 Initial Latency Fixed Latency Enable (64 Mb) Reserved (128 Mb) 2 1-0 Hybrid Burst Enable Burst Length Document Number: 001-97964 Rev. *L Settings (Binary) 1 - Normal operation (default) 0 - Writing 0 to CR[15] causes the device to enter Deep Power Down Reserved for 128 Mb dual-die stack 000 - 34 ohms (default) 001 - 115 ohms 010 - 67 ohms 011 - 46 ohms 100 - 34 ohms 101 - 27 ohms 110 - 22 ohms 111 - 19 ohms 1 - Reserved (default) Reserved for Future Use. When writing this register, these bits should be set to 1 for future compatibility. 0000 - 5 Clock Latency - 133 MHz 0001 - 6 Clock Latency - 166 MHz (default) 0010 - Reserved 0011 - Reserved 0100 - Reserved ... 1101 - Reserved 1110 - 3 Clock Latency - 83 MHz 1111 - 4 Clock Latency - 100 MHz 0 - Variable Latency - 1 or 2 times Initial Latency depending on RWDS during CA cycles. 1 - Fixed 2 times Initial Latency (default) 1 - Fixed 2 times Initial Latency (default) 0: Wrapped burst sequences to follow hybrid burst sequencing 1: Wrapped burst sequences in legacy wrapped burst manner (default) 00 - 128 bytes 01 - 64 bytes 10- 16 bytes 11 - 32 bytes (default) Page 21 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 5.2.1.1 Wrapped Burst A wrapped burst transaction accesses memory within a group of words aligned on a word boundary matching the length of the configured group. Wrapped access groups can be configured as 16, 32, 64, or 128 bytes alignment and length. During wrapped transactions, access starts at the Command-Address selected location within the group, continues to the end of the configured word group aligned boundary, then wraps around to the beginning location in the group, then continues back to the starting location. Wrapped bursts are generally used for critical word first instruction or data cache line fill read accesses. 5.2.1.2 Hybrid Burst The beginning of a hybrid burst will wrap within the target address wrapped burst group length before continuing to the next half-page of data beyond the end of the wrap group. Continued access is in linear burst order until the transfer is ended by returning CS# HIGH. This hybrid of a wrapped burst followed by a linear burst starting at the beginning of the next burst group, allows multiple sequential address cache lines to be filled in a single access. The first cache line is filled starting at the critical word. Then the next sequential line in memory can be read in to the cache while the first line is being processed. Table 10. CR0[2] Control of Wrapped Burst Sequence Bit Default Value 2 1 Name Hybrid Burst Enable CR[2] = 0: Wrapped burst sequences to follow hybrid burst sequencing CR[2] = 1: Wrapped burst sequences in legacy wrapped burst manner Table 11. Example Wrapped Burst Sequences[40] Burst Selection CA[45] CR0[2:0] 0 000 Burst Type Wrap Boundary (bytes) Start Address (Hex) Hybrid 128 03, 04, 05, 06, 07, 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, 1E, 1F, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 2A, 2B, 2C, 2D, 2E, 2F, 30, 31, 32, 33, 34, 35, 128 Wrap 36, 37, 38, 39, 3A, 3B, 3C, 3D, 3E, 3F, 00, 01, 02 once then XXXXXX03 (wrap complete, now linear beyond the end of the initial 128 byte Linear wrap group) 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 4A, 4B, 4C, 4D, 4E, 4F, 50, 51, ... Address Sequence (Hex) (Words) 001 03, 04, 05, 06, 07, 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, 1E, 1F, 00, 01, 02, 64 Wrap (wrap complete, now linear beyond the end of the initial 64 byte Hybrid 64 once then XXXXXX03 wrap group) Linear 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 2A, 2B, 2C, 2D, 2E, 2F, 30, 31, ... 0 001 2E, 2F, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 3A, 3B, 3C, 3D, 3E, 3F, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 2A, 2B, 2C, 2D, 64 Wrap (wrap complete, now linear beyond the end of the initial 64 byte Hybrid 64 once then XXXXXX2E wrap group) Linear 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 4A, 4B, 4C, 4D, 4E, 4F, 50, 51, ... 0 010 02, 03, 04, 05, 06, 07, 00, 01, 16 Wrap complete, now linear beyond the end of the initial 16 byte wrap Hybrid 16 once then XXXXXX02 (wrap group) Linear 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, ... 0 Note 40. Linear Burst across die boundary is not supported in 128-Mb dual-die stack. Document Number: 001-97964 Rev. *L Page 22 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 11. Example Wrapped Burst Sequences[40] (Continued) Burst Selection CA[45] CR0[2:0] Burst Type Wrap Boundary (bytes) Start Address (Hex) Address Sequence (Hex) (Words) 0 010 0C, 0D, 0E, 0F, 08, 09, 0A, 0B, 16 Wrap complete, now linear beyond the end of the initial 16 byte wrap Hybrid 16 once then XXXXXX0C (wrap group) Linear 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, ... 0 011 32 Wrap 0A, 0B, 0C, 0D, 0E, 0F, 00, 01, 02, 03, 04, 05, 06, 07, 08, 09, ... Hybrid 32 once then XXXXXX0A Linear 0 011 32 Wrap 1E, 1F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, ... Hybrid 32 once then XXXXXX1E Linear 0 100 Wrap 128 128 03, 04, 05, 06, 07, 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, 1E, 1F, 20, 21, 22, 23, 24, XXXXXX03 25, 26, 27, 28, 29, 2A, 2B, 2C, 2D, 2E, 2F, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 3A, 3B, 3C, 3D, 3E, 3F, 00, 01, 02, ... 0 101 Wrap 64 64 XXXXXX03 03, 04, 05, 06, 07, 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, 1E, 1F, 00, 01, 02, ... 0 101 Wrap 64 64 XXXXXX2E 2E, 2F, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 3A, 3B, 3C, 3D, 3E, 3F, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 2A, 2B, 2C, 2D, ... 0 110 Wrap 16 16 XXXXXX02 02, 03, 04, 05, 06, 07, 00, 01, ... 0 110 Wrap 16 16 XXXXXX0C 0C, 0D, 0E, 0F, 08, 09, 0A, 0B, ... 0 111 Wrap 32 32 XXXXXX0A 0A, 0B, 0C, 0D, 0E, 0F, 00, 01, 02, 03, 04, 05, 06, 07, 08, 09, ... 0 111 Wrap 32 32 XXXXXX1E 1E, 1F, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 1A, 1B, 1C, 1D, ... 1 XXX Linear Linear Burst 04, 05, 06, 07, 08, 09, 0A, 0B, 0C, 0D, 0E, 0F, 10, 11, 12, 13, 14, 15, XXXXXX03 03, 16, 17, 18, ... Note 40. Linear Burst across die boundary is not supported in 128-Mb dual-die stack. 5.2.1.3 Initial Latency Memory Space read and write transactions or Register Space read transactions require some initial latency to open the row selected by the Command-Address. This initial latency is tACC. The number of latency clocks needed to satisfy tACC depends on the HyperBus frequency and can vary from 3 to 6 clocks. The value in CR0[7:4] selects the number of clocks for initial latency. The default value is 6 clocks, allowing for operation up to a maximum frequency of 166MHz prior to the host system setting a lower initial latency value that may be more optimal for the system. In the event a distributed refresh is required at the time a Memory Space read or write transaction or Register Space read transaction begins, the RWDS signal goes HIGH during the Command-Address to indicate that an additional initial latency is being inserted to allow a refresh operation to complete before opening the selected row. Register Space write transactions always have zero initial latency. RWDS may be HIGH or LOW during the Command-Address period. The level of RWDS during the Command-Address period does not affect the placement of register data immediately after the Command-Address, as there is no initial latency needed to capture the register data. A refresh operation may be performed in the memory array in parallel with the capture of register data. Document Number: 001-97964 Rev. *L Page 23 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 5.2.1.4 Fixed Latency A configuration register option bit CR0[3] is provided to make all Memory Space read and write transactions or Register Space read transactions require the same initial latency by always driving RWDS HIGH during the Command-Address to indicate that two initial latency periods are required. This fixed initial latency is independent of any need for a distributed refresh, it simply provides a fixed (deterministic) initial latency for all of these transaction types. The fixed latency option may simplify the design of some HyperBus memory controllers or ensure deterministic transaction performance. Fixed latency is the default POR or reset configuration. The system may clear this configuration bit to disable fixed latency and allow variable initial latency with RWDS driven HIGH only when additional latency for a refresh is required. Note 128-Mb dual-die stack only supports fixed latency. 5.2.1.5 Drive Strength DQ signal line loading, length, and impedance vary depending on each system design. Configuration register bits CR0[14:12] provide a means to adjust the DQ[7:0] signal output impedance to customize the DQ signal impedance to the system conditions to minimize high-speed signal behaviors such as overshoot, undershoot, and ringing. The default POR or reset configuration value is 000b to select the mid point of the available output impedance options. The impedance values shown are typical for both pull-up and pull-down drivers at typical silicon process conditions, nominal operating voltage (1.8 V or 3.0 V) and 50C. The impedance values may vary by up to 80% from the typical values depending on the Process, Voltage, and Temperature (PVT) conditions. Impedance will increase with slower process, lower voltage, or higher temperature. Impedance will decrease with faster process, higher voltage, or lower temperature. Each system design should evaluate the data signal integrity across the operating voltage and temperature ranges to select the best drive strength settings for the operating conditions. 5.2.1.6 Deep Power Down When the HyperRAM device is not needed for system operation, it may be placed in a very low power consuming mode called Deep Power Down (DPD), by writing 0 to CR0[15]. When CR0[15] is cleared to 0, the device enters the DPD mode within tDPDIN time and all refresh operations stop. The data in RAM is lost, (becomes invalid without refresh) during DPD mode. The next access to the device driving CS# LOW then HIGH, POR, or a reset will cause the device to exit DPD mode. Returning to Standby mode requires tDPDOUT time. For additional details see Section 6.1.3, Deep Power Down on page 27. Note: The Deep Power Down option is not supported in 128-Mb dual-die stack. 5.2.2 Configuration Register 1 Configuration Register 1 (CR1) is used to define the distributed refresh interval for this HyperRAM device. The core DRAM array requires periodic refresh of all bits in the array. This can be done by the host system by reading or writing a location in each row within a specified time limit. The read or write access copies a row of bits to an internal buffer. At the end of the access the bits in the buffer are written back to the row in memory, thereby recharging (refreshing) the bits in the row of DRAM memory cells. However, the host system generally has better things to do than to periodically read every row in memory and keep track that each row is visited within the required refresh interval for the entire memory array. HyperRAM devices include self-refresh logic that will refresh rows automatically so that the host system is relieved of the need to refresh the memory. The automatic refresh of a row can only be done when the memory is not being actively read or written by the host system. The refresh logic waits for the end of any active read or write before doing a refresh, if a refresh is needed at that time. If a new read or write begins before the refresh is completed, the memory will drive RWDS HIGH during the Command-Address period to indicate that an additional initial latency time is required at the start of the new access in order to allow the refresh operation to complete before starting the new access. The required refresh interval for the entire memory array varies with temperature as shown in Table 12, Array Refresh Interval per Temperature on page 25. This is the time within which all rows must be refreshed. Refresh of all rows could be done as a single batch of accesses at the beginning of each interval, in groups (burst refresh) of several rows at a time, spread throughout each interval, or as single row refreshes evenly distributed throughout the interval. The self-refresh logic distributes single row refresh operations throughout the interval so that the memory is not busy doing a burst of refresh operations for a long period, such that the burst refresh would delay host access for a long period. Document Number: 001-97964 Rev. *L Page 24 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 12. Array Refresh Interval per Temperature Device Temperature (C) Array Refresh Interval (ms) Array Rows Recommended tCMS (s) 85 64 8192 4 105 16 8192 1 Table 13. Configuration Register 1 Bit Assignments CR1 Bit 15-2 1-0 Function Reserved Settings (Binary) 000000h -- Reserved (default) Reserved for Future Use. When writing this register, these bits should be cleared to 0 for future compatibility. 10b -- default 4 s for Industrial temperature range devices 1 s for Industrial Plus temperature range devices Distributed Refresh Interval 11b -- 1.5 times default 00b -- 2 times default 01b -- 4 times default The distributed refresh method requires that the host does not do burst transactions that are so long as to prevent the memory from doing the distributed refreshes when they are needed. This sets an upper limit on the length of read and write transactions so that the refresh logic can insert a refresh between transactions. This limit is called the CS# LOW maximum time (tCMS). The tCMS value is determined by the array refresh interval divided by the number of rows in the array, then reducing this calculation by half to ensure that a distributed refresh interval cannot be entirely missed by a maximum length host access starting immediately before a distributed refresh is needed. Because tCMS is set to half the required distributed refresh interval, any series of maximum length host accesses that delay refresh operations will be catching up on refresh operations at twice the rate required by the refresh interval divided by the number of rows. The host system is required to respect the tCMS value by ending each transaction before violating tCMS. This can be done by host memory controller logic splitting long transactions when reaching the tCMS limit, or by host system hardware or software not performing a single read or write transaction that would be longer than tCMS. As noted in Table 12 on page 25 the array refresh interval is longer at lower temperatures such that tCMS could be increased to allow longer transactions. The host system can either use the tCMS value from the table for the maximum operating temperature or, may determine the current operating temperature from a temperature sensor in the system in order to set a longer distributed refresh interval. The host system may also effectively increase the tCMS value by explicitly taking responsibility for performing all refresh and doing burst refresh reading of multiple sequential rows in order to catch up on distributed refreshes missed by longer transactions. Document Number: 001-97964 Rev. *L Page 25 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 6. Interface States Table 14 describes the required value of each signal for each interface state. Table 14. Interface States Interface State Power-Off VCC / VCCQ CS# CK, CK# DQ7-DQ0 RWDS RESET# < VLKO X X HI-Z HI-Z X X X HI-Z HI-Z X X X HI-Z HI-Z L Interface Standby VCC / VCCQ min VCC / VCCQ min VCC / VCCQ min H X HI-Z HI-Z H Command-Address VCC / VCCQ min L T Master Output Valid X H Read Initial Access Latency (data bus turn around period) VCC / VCCQ min L T HI-Z L H Write Initial Access Latency (RWDS turn around period) VCC / VCCQ min L T HI-Z HI-Z H Read data transfer VCC / VCCQ min L T Slave Output Valid Slave Output Valid X or T H Master Output Valid X or T H Power-On (Cold) Reset Hardware (Warm) Reset Write data transfer with Initial Latency VCC / VCCQ min L T Master Output Valid Write data transfer without Initial Latency[41] VCC / VCCQ min L T Master Output Valid Slave Output L or HI-Z H Active Clock Stop[42] VCC / VCCQ min L Idle Master or Slave Output Valid or HI-Z X H Deep Power Down[42] VCC / VCCQ min H X or T Slave Output HI-Z HI-Z H Notes 41. Writes without initial latency (with zero initial latency), do not have a turn around period for RWDS. The HyperRAM device will always drive RWDS during the Command-Address period to indicate whether extended latency is required. Since master write data immediately follows the Command-Address period the HyperRAM device may continue to drive RWDS LOW or may take RWDS to HI-Z. The master must not drive RWDS during Writes with zero latency. Writes with zero latency do not use RWDS as a data mask function. All bytes of write data are written (full word writes). 42. Active Clock Stop is described in Section 6.1.2, Active Clock Stop on page 27. DPD is described in Section 6.1.3, Deep Power Down on page 27. Legend L = VIL H = VIH X = either VIL or VIH L/H = rising edge H/L = falling edge T = Toggling during information transfer Idle = CK is LOW and CK# is HIGH. Valid = all bus signals have stable L or H level Document Number: 001-97964 Rev. *L Page 26 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 6.1 Power Conservation Modes 6.1.1 Interface Standby Standby is the default, low-power, state for the interface while the device is not selected by the host for data transfer (CS#= HIGH). All inputs, and outputs other than CS# and RESET# are ignored in this state. 6.1.2 Active Clock Stop The Active Clock Stop mode reduces device interface energy consumption to the ICC6 level during the data transfer portion of a read or write operation. The device automatically enables this mode when clock remains stable for tACC + 30 ns. While in Active Clock Stop mode, read data is latched and always driven onto the data bus. ICC6 shown in Section 7.4, DC Characteristics on page 30. Active Clock Stop mode helps reduce current consumption when the host system clock has stopped to pause the data transfer. Even though CS# may be LOW throughout these extended data transfer cycles, the memory device host interface will go into the Active Clock Stop current level at tACC + 30 ns. This allows the device to transition into a lower current mode if the data transfer is stalled. Active read or write current will resume once the data transfer is restarted with a toggling clock. The Active Clock Stop mode must not be used in violation of the tCSM limit. CS# must go HIGH before tCSM is violated. 6.1.3 Deep Power Down In the Deep Power Down (DPD) mode, current consumption is driven to the lowest possible level (iDPD). DPD mode is entered by writing a 0 to CR0[15]. The device reduces power within tDPDIN time and all refresh operations stop. The data in Memory Space is lost, (becomes invalid without refresh) during DPD mode. The next access to the device, driving CS# LOW then HIGH, will cause the device to exit DPD mode. A read or write transaction used to drive CS# LOW then HIGH to exit DPD mode is a dummy transaction that is ignored by the device. Also, POR, or a hardware reset will cause the device to exit DPD mode. Only the CS# and RESET# signals are monitored during DPD mode. Returning to Standby mode following a dummy transaction or reset requires tDPDOUT time. Returning to Standby mode following a POR requires tVCS time, as with any other POR. Following the exit from DPD due to any of these events, the device is in the same state as following POR. Table 15. Deep Power Down Timing Parameters Parameter Description Min Max Unit Deep Power Down CR0[15]=0 register write to DPD power level 10 s tDPDCSL Length of CS# LOW period to cause an exit from Deep Power Down 200 ns tDPDOUT CS# LOW then HIGH to Standby wakeup time 150 s tDPDIN Figure 14. Deep Power Down Entry Timing CS# CK , CK# DQ[7:0] tDPDIN Phase Write Command-Address CR Value Enter DPD Mode DPD mode Figure 15. Deep Power Down CS# Exit Timing t DPDCSL CS# CK , CK# DQ[7:0] t DPDOUT Phase DPD mode Dummy Transaction to Exit DPD Exit DPD Mode Standby New Transaction Notes 43. The Deep Power Down option is not supported in 128-Mb dual-die stack. Document Number: 001-97964 Rev. *L Page 27 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7. 7.1 Electrical Specifications Absolute Maximum Ratings 65 C to +150 C 65C to +115 C Storage Temperature Plastic Packages Ambient Temperature with Power Applied Voltage with Respect to Ground 0.5V to +(VCC + 0.5V) All signals[44] ) Output Short Circuit Current[45] 100 mA 0.5V to +4.0V VCC 7.1.1 Input Signal Overshoot During DC conditions, input or I/O signals should remain equal to or between VSS and VDD. During voltage transitions, inputs or I/Os may negative overshoot VSS to 1.0V or positive overshoot to VDD +1.0V, for periods up to 20 ns. Figure 16. Maximum Negative Overshoot Waveform VSSQ to VCCQ - 1.0V 20 ns Figure 17. Maximum Positive Overshoot Waveform 20 ns VCCQ + 1.0V VSSQ to VCCQ Notes 44. Minimum DC voltage on input or I/O signal is 1.0V. During voltage transitions, input or I/O signals may undershoot VSS to -1.0V for periods of up to 20 ns. See Figure 16. Maximum DC voltage on input or I/O signals is VCC +1.0V. During voltage transitions, input or I/O signals may overshoot to VCC +1.0V for periods up to 20 ns. See Figure 17. 45. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 46. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Document Number: 001-97964 Rev. *L Page 28 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7.2 Latchup Characteristics Table 7.1 Latchup Specification[47] Description Min Max Unit Input voltage with respect to VSSQ on all input only connections Input voltage with respect to VSSQ on all I/O connections 1.0 VCCQ + 1.0 V 1.0 VCCQ + 1.0 V VCCQ Current 100 +100 mA Note 47. Excludes power supplies VCC/VCCQ. Test conditions: VCC = VCCQ = 1.8 V, one connection at a time tested, connections not being tested are at VSS. 7.3 Operating Ranges Operating ranges define those limits between which the functionality of the device is guaranteed. 7.3.1 Temperature Ranges Parameter Symbol Ambient Temperature 7.3.2 TA Spec Device Min Max Industrial (I) -40 85 Industrial Plus (V) -40 105 Automotive, AEC-Q100 Grade 3 (A) -40 85 Automotive, AEC-Q100 Grade 2 (B) -40 105 Unit C Power Supply Voltages VCC and VCCQ 1.7 V to 1.95 V VCC and VCCQ 2.7 V to 3.6 V Document Number: 001-97964 Rev. *L Page 29 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7.4 DC Characteristics Table 16. DC Characteristics (CMOS Compatible) Parameter Description Test Conditions 64 Mb 128 Mb Min Typ[48] Max Min Typ[48] Max Unit ILI Input Leakage Current 3.0 V Device Reset Signal HIGH Only VIN = VSS to VCC, VCC = VCC max 0.1 0.2 A ILI Input Leakage Current 1.8 V Device Reset Signal HIGH Only VIN = VSS to VCC, VCC = VCC max 0.1 0.2 A ILI Input Leakage Current 3.0 V Device Reset Signal LOW Only[49] VIN = VSS to VCC, VCC = VCC max +20.0 +40.0 A ILI Input Leakage Current 1.8 V Device Reset Signal LOW Only[49] VIN = VSS to VCC, VCC = VCC max +20.0 +40.0 A 20 60 29 72 mA 20 35 32 47 mA 15 60 23 72 mA 15 35 27 47 mA CS# = VIH, 135 200 286 400 A CS# = VIH, 135 300 312 600 A 10 20 20 40 mA 5.3 8 11 16 mA 5.3 12 12 24 mA 35 70 mA ICC1 ICC2 VCC Active Read Current VCC Active Write Current ICC4I VCC Standby Current for Industrial (40 C to +85 C) ICC4IP VCC Standby Current for Industrial Plus (40 C to +105 C) CS# = VIL, @166 MHz, VCC = 1.9V CS# = VIL, @100 MHz, VCC = 3.6V CS# = VIL, @166 MHz, VCC = 1.9V CS# = VIL, @100 MHz, VCC = 3.6V VCC = VCC max VCC = VCC max CS# = VIH, RESET# = VIL, VCC = VCC max ICC5 Reset Current ICC6I Active Clock Stop Current for Industrial (40 C to +85 C) RESET# = VIH, VCC = VCC max ICC6IP Active Clock Stop Current for Industrial Plus(40 C to +105 C) RESET# = VIH, VCC = VCC max CS# = VIL, CS# = VIL, CS# = VIH, VCC = VCC max, VCC = VCCQ = 1.95V or 3.6V ICC7 VCC Current during power up[48] IDPD Deep Power Down Current 3.0 V 85C CS# = VIH, VCC = 3.6V, TA = 85 C 20 N/A A IDPD Deep Power Down Current 1.8 V 85C CS# = VIH, VCC = 1.9V, TA = 85 C 10 N/A A IDPD Deep Power Down Current 3.0 V 105C CS# = VIH, VCC = 3.6V, TA = 105 C 40 N/A A Notes 48. Not 100% tested. 49. RESET# LOW initiates exits from DPD mode and initiates the draw of ICC5 reset current, making ILI during Reset# LOW insignificant. Document Number: 001-97964 Rev. *L Page 30 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 16. DC Characteristics (CMOS Compatible) (Continued) Parameter IDPD Description Deep Power Down Current 1.8 V 105C 64 Mb Test Conditions 128 Mb Min Typ[48] Max Min Typ[48] Max 20 N/A 0.5 CS# = VIH, VCC = 1.9V, TA = 105 C VIL Input LOW Voltage 0.5 0.3 x VCC VIH Input HIGH Voltage 0.7 x VCC VCC + 0.3 0.7 x VCC VOL Output LOW Voltage IOL = 100 A for DQ[7:0] 0.15 x VCC VOH Output HIGH Voltage IOH = 100 A for DQ[7:0] 0.85 x VCC Unit A 0.3 x VCC V VCC + 0.3 V 0.15 x VCC V 0.85 x VCC V Notes 48. Not 100% tested. 49. RESET# LOW initiates exits from DPD mode and initiates the draw of ICC5 reset current, making ILI during Reset# LOW insignificant. 7.4.1 HIGHCapacitance Characteristics Table 7.2 1.8 V Capacitive Characteristics[50, 51, 52] Description Parameter Input Capacitance (CK, CK#, CS#) CI 64 Mb 128 Mb Min Max Min Max 3 4.5 6 9 Unit pF Delta Input Capacitance (CK, CK#) CID 0.25 0.5 pF Output Capacitance (RWDS) CO 3 4 6 8 pF IO Capacitance (DQx) CIO 3 4 6 8 pF CIOD 0.5 1 pF IO Capacitance Delta (DQx) Notes 50. These values are guaranteed by design and are tested on a sample basis only. 51. Contact capacitance is measured according to JEP147 procedure for measuring capacitance using a vector network analyzer. VCC, VCCQ are applied and all other signals (except the signal under test) floating. DQ's should be in the HI-Z state. 52. Note that the capacitance values for the CK, CK#, RWDS and DQx signals must have similar capacitance values to allow for signal propagation time matching in the system. The capacitance value for CS# is not as critical because there are no critical timings between CS# going active (LOW) and data being presented on the DQs bus. Table 7.3 3.0 V Capacitive Characteristics[53, 54, 55] 64 Mb Description 128 Mb Parameter Min Max Min Max Unit Input Capacitance (CK, CS#) CI 3 4.5 6 9 pF Output Capacitance (RWDS) CO 3 4 6 8 pF IO Capacitance (DQx) CIO 3 4 6 8 pF CIOD 0.5 1 pF IO Capacitance Delta (DQx) Notes 53. These values are guaranteed by design and are tested on a sample basis only. 54. Contact capacitance is measured according to JEP147 procedure for measuring capacitance using a vector network analyzer. VCC, VCCQ are applied and all other signals (except the signal under test) floating. DQ's should be in the HI-Z state. 55. The capacitance values for the CK, RWDS and DQx signals must have similar capacitance values to allow for signal propagation time matching in the system. The capacitance value for CS# is not as critical because there are no critical timings between CS# going active (LOW) and data being presented on the DQs bus. Document Number: 001-97964 Rev. *L Page 31 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7.5 Power-Up Initialization HyperRAM products include an on-chip voltage sensor used to launch the power-up initialization process. VCC and VCCQ must be applied simultaneously. When the power supply reaches a stable level at or above VCC(min), the device will require tVCS time to complete its self-initialization process. The device must not be selected during power-up. CS# must follow the voltage applied on VCCQ until VCC (min) is reached during power-up, and then CS# must remain HIGH for a further delay of tVCS. A simple pull-up resistor from VCCQ to Chip Select (CS#) can be used to insure safe and proper power-up. If RESET# is LOW during power up, the device delays start of the tVCS period until RESET# is HIGH. The tVCS period is used primarily to perform refresh operations on the DRAM array to initialize it. When initialization is complete, the device is ready for normal operation. Figure 18. Power-up with RESET# HIGH Vcc_VccQ VCC Minimum Device Access Allowed tVCS CS# RESET# Figure 19. Power-up with RESET# LOW Vcc_VccQ VCC Minimum CS# Device Access Allowed tVCS RESET# Table 17. Power Up and Reset Parameters[56, 57, 58] Parameter Description Min Max Unit VCC 1.8 V VCC Power Supply 1.7 1.95 V VCC 3.0 V VCC Power Supply 2.7 3.6 V tVCS VCC and VCCQ minimum and RESET# HIGH to first access 150 s Notes 56. Bus transactions (read and write) are not allowed during the power-up reset time (tVCS). 57. VCCQ must be the same voltage as VCC. 58. VCC ramp rate may be non-linear. Document Number: 001-97964 Rev. *L Page 32 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7.6 Power Down HyperRAM devices are considered to be powered-off when the core power supply (VCC) drops below the VCC Lock-Out voltage (VLKO). During a power supply transition down to the VSS level, VCCQ should remain less than or equal to VCC. At the VLKO level, the HyperRAM device will have lost configuration or array data. VCC must always be greater than or equal to VCCQ (VCC VCCQ). During Power-Down or voltage drops below VLKO, the core power supply voltages must also drop below VCC Reset (VRST) for a Power Down period (tPD) for the part to initialize correctly when the power supply again rises to VCC minimum. See Figure 20. If during a voltage drop the VCC stays above VLKO the part will stay initialized and will work correctly when VCC is again above VCC minimum. If VCC does not go below and remain below VRST for greater than tPD, then there is no assurance that the POR process will be performed. In this case, a hardware reset will be required ensure the HyperBus device is properly initialized. Figure 20. Power Down or Voltage Drop VCC (Max) VCC No Device Access Allowed VCC (Min) tVCS VLKO Device Access Allowed VRST t PD Time The following section describes HyperRAM device dependent aspects of power down specifications. Table 18. 1.8 V Power-Down Voltage and Timing[59] Symbol Parameter Min Max Unit VCC VCC Power Supply 1.7 1.95 V VLKO VCC Lock-out below which re-initialization is required 1.7 V VRST VCC LOW Voltage needed to ensure initialization will occur 0.8 V 30 s tPD Duration of VCC VRST Note 59. VCC ramp rate can be non-linear. Table 19. 3.0 V Power-Down Voltage and Timing[60] Symbol Min Max Unit VCC VCC Power Supply 2.7 3.6 V VLKO VCC Lock-out below which re-initialization is required 2.7 V VRST VCC LOW Voltage needed to ensure initialization will occur 0.8 V 50 s tPD Parameter Duration of VCC VRST Note 60. VCC ramp rate can be non-linear. Document Number: 001-97964 Rev. *L Page 33 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 7.7 Hardware Reset The RESET# input provides a hardware method of returning the device to the standby state. During tRPH the device will draw ICC5 current. If RESET# continues to be held LOW beyond tRPH, the device draws CMOS standby current (ICC4). While RESET# is LOW (during tRP), and during tRPH, bus transactions are not allowed. A hardware reset will: cause the configuration registers to return to their default values, halt self-refresh operation while RESET# is LOW, and force the device to exit the Deep Power Down state. After RESET# returns HIGH, the self-refresh operation will resume. Because self-refresh operation is stopped during RESET# LOW, and the self-refresh row counter is reset to its default value, some rows may not be refreshed within the required array refresh interval per Table 12 on page 25. This may result in the loss of DRAM array data during or immediately following a hardware reset. The host system should assume DRAM array data is lost after a hardware reset and reload any required data. Figure 21. Hardware Reset Timing Diagram tRP RESET# tVCS - if RESET# Low > tRP max tRH tRPH CS# Table 20. Power Up and Reset Parameters Parameter Min Max Unit tRP RESET# Pulse Width Description 200 ns tRH Time between RESET# (HIGH) and CS# (LOW) 200 ns tRPH RESET# LOW to CS# LOW 400 ns Document Number: 001-97964 Rev. *L Page 34 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 8. Timing Specifications The following section describes HyperRAM device dependent aspects of timing specifications. 8.1 Key to Switching Waveforms Valid_High_or_Low High_to_Low_Transition Low_to_High_Transition Invalid High_Impedance 8.2 AC Test Conditions Figure 22. Test Setup Device Under Test CL Table 21. Test Specification[63] Parameter All Speeds Units 20 pF Output Load Capacitance, CL [62] 2.0 V/ns 0.0-VCCQ V Input timing measurement reference levels VCCQ/2 V Output timing measurement reference levels VCCQ/2 V Minimum Input Rise and Fall Slew Rates Input Pulse Levels Notes 62. All AC timings assume an input slew rate of 2V/ns. CK/CK# differential slew rate of at least 4V/ns. 63. Input and output timing is referenced to VCCQ/2 or to the crossing of CK/CK#. Figure 23. Input Waveforms and Measurement Levels[61] VccQ Input VccQ / 2 Measurement Level VccQ / 2 Output Vss Note 61. Input timings for the differential CK/CK# pair are measured from clock crossings. Document Number: 001-97964 Rev. *L Page 35 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 8.3 AC Characteristics 8.3.1 Read Transactions Table 22. HyperRAM Specific 1.8 V Read Timing Parameters Parameter Symbol 166 MHz 133 MHz 100 MHz Min Max Min Max Min Max Unit Chip Select HIGH Between Transactions tCSHI 6 - 7.5 - 10.0 - ns HyperRAM Read-Write Recovery Time tRWR 36 37.5 40 ns Chip Select Setup to next CK Rising Edge tCSS 3 - 3 - 3 - ns Data Strobe Valid tDSV - 12 - 12 - 12 ns Input Setup tIS 0.6 - 0.8 - 1.0 - ns Input Hold tIH 0.6 - 0.8 - 1.0 - ns HyperRAM Read Initial Access Time tACC 36 37.5 40 ns Clock to DQs Low Z tDQLZ 0 - 0 - 0 - ns tCKD 1 tCKDI 0 tDV 1.7 tCKDS 1 tDSS -0.45 +0.45 -0.6 +0.6 -0.8 +0.8 RWDS transition to DQ Invalid tDSH -0.45 +0.45 -0.6 +0.6 -0.8 +0.8 ns Chip Select Hold After CK Falling Edge tCSH 0 - 0 - 0 - ns Chip Select Inactive to RWDS HI-Z tDSZ - 6 - 6 - 6 ns Chip Select Inactive to DQ HI-Z tOZ - 6 - 6 - 6 ns - 4.0 - 4.0 - 4.0 us - 1.0 - 1.0 - 1.0 us 36 37.5 40 ns CK transition to DQ Valid (64 Mb) CK transition to DQ Valid (128 Mb) CK transition to DQ Invalid (64 Mb) CK transition to DQ Invalid (128 Mb) Data Valid (tDV min = the lessor of: tCKHP min - tCKD max + tCKDI max) or tCKHP min - tCKD min + tCKDI min) CK transition to RWDS valid (64 Mb) CK transition to RWDS valid (128 Mb) RWDS transition to DQ Valid HyperRAM Chip Select Maximum LOW Time - Industrial Temperature HyperRAM Chip Select Maximum LOW Time - Industrial Plus Temperature Refresh Time Document Number: 001-97964 Rev. *L 5.5 6.0 4.6 5.6 - 5.5 6.0 1 0 2.375 1 5.5 6.0 4.5 5.5 - 5.5 6.0 1 0 3.3 1 5.5 6.0 4.3 5.3 - 5.5 6.0 ns ns ns ns ns tCSM tRFH Page 36 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 23. HyperRAM Specific 3.0 V Read Timing Parameters Parameter 100 MHz Symbol Min Max Unit Chip Select HIGH Between Transactions tCSHI 10.0 - ns HyperRAM Read-Write Recovery Time tRWR 40 - ns Chip Select Setup to next CK Rising Edge tCSS 3 - ns Data Strobe Valid tDSV - 12 ns Input Setup tIS 1.0 - ns Input Hold tIH 1.0 - ns HyperRAM Read Initial Access Time tACC 40 - ns Clock to DQs Low Z tDQLZ 0 - ns HyperRAM CK transition to DQ Valid (64 Mb) 7 tCKD 1 tCKDI 0.5 tDV 2.7 tCKDS 1 RWDS transition to DQ Valid tDSS -0.8 +0.8 RWDS transition to DQ Invalid tDSH -0.8 +0.8 ns Chip Select Hold After CK Falling Edge tCSH 0 - ns Chip Select Inactive to RWDS HI-Z tDSZ - 7 ns Chip Select Inactive to DQ HI-Z tOZ - 7 ns - 4.0 us - 1.0 us 40 ns HyperRAM CK transition to DQ Valid (128 Mb) HyperRAM CK transition to DQ Invalid (64 Mb) HyperRAM CK transition to DQ Invalid (128 Mb) Data Valid (tDV min = the lessor of: tCKHP min - tCKD max + tCKDI max) or tCKHP min - tCKD min + tCKDI min) CK transition to RWDS valid (64 Mb) CK transition to RWDS valid (128 Mb) HyperRAM Chip Select Maximum LOW Time - Industrial Temperature HyperRAM Chip Select Maximum LOW Time - Industrial Plus Temperature Refresh Time tCSM tRFH ns 8 5.2 ns 6.2 ns 7 ns 8 ns Figure 24. Read Timing Diagram -- No Additional Latency Required t CSHI t CSM CS# t CSS t CSH t RWR =Read Write Recovery t ACC = Access t CSS CK , CK# t DSV RWDS 4 cycle latency t CKDS t DSZ High = 2x Latency Count Low = 1x Latency Count t DSS t IS DQ[7:0] t IH 47:40 39:32 31:24 23:16 15:8 Command-Address t CKD Dn A 7:0 Host drives DQ[7:0] and Memory drives RWDS Document Number: 001-97964 Rev. *L t DQLZ RWDS and Data are edge aligned t OZ t DSH Dn B Dn+1 A Dn+1 B Memory drives DQ[7:0] and RWDS Page 37 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 8.3.2 Write Transactions Table 24. 1.8 V Write Timing Parameters Parameter 166 MHz Symbol 133 MHz 100 MHz Min Max Min Max Min Max Unit Read-Write Recovery Time tRWR 36 37.5 40 ns Access Time tACC 36 37.5 40 ns Refresh Time tRFH 36 37.5 40 ns 4.0 4.0 4.0 s 1.0 1.0 1.0 s 0 0 0 ns Chip Select Maximum LOW Time Industrial Temperature tCSM Chip Select Maximum LOW Time Industrial Plus Temperature RWDS Data Mask Valid tDMV Table 25. 3.0 V Write Timing Parameters Parameter 100 MHz Symbol Min Max Unit Read-Write Recovery Time tRWR 40 ns Access Time tACC 40 ns Refresh Time tRFH 40 ns 4.0 s 1.0 s 0 ns Chip Select Maximum LOW Time Industrial Temperature tCSM Chip Select Maximum LOW Time Industrial Plus Temperature RWDS Data Mask Valid tDMV Note 64. Refer to Table 23 for parameters that are shown in the timing diagram but not listed in this table. Figure 25. Write Timing Diagram -- No Additional Latency t CSHI t CSM CS# t CSS t CSH t RWR =Read Write Recovery t ACC = Access t CSS CK, CK# t DSV RWDS 4 cycle latency t DSZ High = 2x Latency Count Low = 1x Latency Count t IS t DMV t IH t IS t IS DQ[7:0] 47:40 t IH 39:32 31:24 t IH 23:16 15:8 Command-Address Host drives DQ[7:0] and Memory drives RWDS Document Number: 001-97964 Rev. *L Dn A 7:0 CK and Data are center aligned Dn B Dn+1 A Dn+1 B Host drives DQ[7:0] and RWDS Page 38 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 9. Physical Interface 9.1 FBGA 24-Ball 5 x 5 Array Footprint HyperRAM devices are provided in Fortified Ball Grid Array (FBGA), 1 mm pitch, 24-ball, 5 x 5 ball array footprint, with 6mm x 8mm body. Figure 26. 24-Ball FBGA, 6 x 8 mm, 5x5 Ball Footprint, Top View[65, 66] 1 2 3 4 5 RFU CS# CK# CK Vss Vcc RFU VssQ RFU RWDS DQ2 RFU VccQ DQ1 DQ0 DQ3 DQ4 DQ7 DQ6 DQ5 VccQ VssQ A RESET# RFU B C D E Notes 65. B1 is assigned to CK# on the 1.8 V device. 66. B1 is a RFU on the 3.0 V device. Document Number: 001-97964 Rev. *L Page 39 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 9.2 9.2.1 Physical Diagrams Fortified Ball Grid Array 24-ball 6 x 8 x 1.0 mm (VAA024) NOTES: DIMENSIONS SYMBOL MIN. NOM. MAX. 1. 2. ALL DIMENSIONS ARE IN MILLIMETERS. 3. BALL POSITION DESIGNATION PER JEP95, SECTION 3, SPP-020. 4. "e" REPRESENTS THE SOLDER BALL GRID PITCH. 5. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION. A - - 1.00 A1 0.20 - - D 8.00 BSC E 6.00 BSC D1 4.00 BSC E1 4.00 BSC MD 5 ME 5 N SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION. N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS FOR MATRIX SIZE MD X ME. 24 b 0.35 0.40 eE 1.00 BSC eD 1.00 BSC SD 0.00 BSC SE 0.00 BSC DIMENSIONING AND TOLERANCING METHODS PER ASME Y14.5M-1994. 6 DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A PLANE PARALLEL TO DATUM C. 7 "SD" AND "SE" ARE MEASURED WITH RESPECT TO DATUMS A AND B AND DEFINE THE 0.45 POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW. WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW "SD" OR "SE" = 0. WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW, "SD" = eD/2 AND "SE" = eE/2. 8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED BALLS. 9. A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK, METALLIZED MARK INDENTATION OR OTHER MEANS. 10. JEDEC SPECIFICATION NO. REF: N/A CYPRESS Company Confidential TITLE THIS DRAWING CONTAINS INFORMATION WHICH IS THE PROPRIETARY PROPERTY OF CYPRESS SEMICONDUCTOR CORPORATION. THIS DRAWING IS RECEIVED IN CONFIDENCE AND ITS CONTENTS MAY NOT BE DISCLOSED WITHOUT WRITTEN CONSENT OF CYPRESS SEMICONDUCTOR CORPORATION. Document Number: 001-97964 Rev. *L DRAWN BY PACKAGE CODE(S) VAA024 ELA024 E2A024 KOTA APPROVED BY BESY DATE 30-AUG-16 PACKAGE OUTLINE, 24 BALL BGA 8.0X6.0X1.0 MM VAA024/ELA024/E2A024 SPEC NO. DATE 30-AUG-16 SCALE : TO FIT REV 002-15550 *A SHEET 1 OF 2 Page 40 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 10. DDR Center Aligned Read Strobe (DCARS) Functionality The HyperRAM device offers an optional feature that enables independent skewing (phase shifting) of the RWDS signal with respect to the read data outputs. This feature is provided in certain devices, based on the Ordering Part Number (OPN). When the DDR Center Aligned Read Strobe (DCARS) feature is provided, a second differential Phase Shifted Clock input PSC/PSC# is used as the reference for RWDS edges instead of CK/CK#. The second clock is generally a copy of CK/CK# that is phase shifted 90 degrees to place the RWDS edges centered within the DQ signals valid data window. However, other degrees of phase shift between CK/CK# and PSC/PSC# may be used to optimize the position of RWDS edges within the DQ signals valid data window so that RWDS provides the desired amount of data setup and hold time in relation to RWDS edges. PSC/PSC# is not used during a write transaction. PSC and PSC# may be driven LOW and HIGH respectively or, both may be driven LOW during write transactions. The PSC/PSC# differential clock is used only in HyperBus devices with 1.8 V nominal core and I/O voltage. HyperBus devices with 3 V nominal core and I/O voltage use only PSC as a single-ended clock. 10.1 HyperRAM Products with DCARS Signal Descriptions Figure 27. HyperBus Product with DCARS Signal Diagram RESET# CS# CK CK# PSC PSC# VCC VCCQ DQ[7:0] RWDS VSS VSSQ Table 26. Signal Descriptions Symbol CS# Type Input Description Chip Select. HyperBus transactions are initiated with a HIGH to LOW transition. HyperBus transactions are terminated with a LOW to HIGH transition. CK, CK# Input Differential Clock. Command-Address/Data information is input or output with respect to the crossing of the CK and CK# signals. CK# is not used on the 3.0 V device, only a single ended CK is used. PSC, PSC# Input Phase Shifted Clock. PSC/PSC# allows independent skewing of the RWDS signal with respect to the CK/CK# inputs. PSC# is only used on the 1.8 V device. PSC (and PSC#) may be driven HIGH and LOW respectively or both may be driven LOW during write transactions. RWDS Output Read-Write Data Strobe. Data bytes output during read transactions are aligned with RWDS based on the phase shift from CK, CK# to PSC, PSC#. PSC, PSC# cause the transitions of RWDS, thus the phase shift from CK, CK# to PSC, PSC# is used to place RWDS edges within the data valid window. RWDS is an input during write transactions to function as a data mask. At the beginning of all bus transactions RWDS is an output and indicates whether additional initial latency count is required (1 = additional latency count, 0 = no additional latency count). DQ[7:0] Input/Output Data Input/Output. Command-Address/Data information is transferred on these DQs during Read and Write transactions. RESET# Input VCC Power Supply Hardware RESET. When LOW the device will self initialize and return to the idle state. RWDS and DQ[7:0] are placed into the HI-Z state when RESET# is LOW. RESET# includes a weak pull-up, if RESET# is left unconnected it will be pulled up to the HIGH state. Power. VCCQ Power Supply Input/Output Power. VSS Power Supply Ground. VSSQ Power Supply Input/Output Ground. Document Number: 001-97964 Rev. *L Page 41 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 10.2 HyperRAM Products with DCARS -- FBGA 24-ball, 5 x 5 Array Footprint Figure 28. 24-ball FBGA, 5 x 5 Ball Footprint, Top View[67, 68] 1 2 3 4 5 RFU CS# CK# CK Vss Vcc PSC VssQ RFU RWDS DQ2 PSC# VccQ DQ1 DQ0 DQ3 DQ4 DQ7 DQ6 DQ5 VccQ VssQ A RESET# RFU B C D E 10.3 HyperRAM Memory with DCARS Timing The illustrations and parameters shown here are only those needed to define the DCARS feature and show the relationship between the Phase Shifted Clock, RWDS, and data. Figure 29. HyperRAM Memory DCARS Timing Diagram[69, 70, 71, 72] t CSHI CS# t CSH t CSS t ACC = Access time t CSS CK , CK# 4 cycle latency PSC , PSC# t DSV t PSCRWDS t DSZ High = 2x Latency Count Low = 1x Latency Count RWDS t IS DQ[7:0] t IH 47:40 39:32 31:24 23:16 15:8 t DQLZ Dn A 7:0 Command-Address t CKD RWDS aligned by PSC t OZ Dn B Dn+1 A Dn+1 B Memory drives DQ[7:0] and RWDS Host drives DQ[7:0] and Memory drives RWDS Notes 67. B1 is an RFU on the 3.0 V device and is assigned to CK# on the 1.8 V device. 68. C5 is an RFU on the 3.0 V device and is assigned to PSC# on the 1.8 V device. 69. Transactions must be initiated with CK = LOW and CK# = HIGH. CS# must return HIGH before a new transaction is initiated. 70. CK# and PSC# are only used on the 1.8 V device. The 3 V device uses a single ended CK and PSC input. 71. The memory drives RWDS during read transactions. 72. This example demonstrates a latency code setting of four clocks and no additional initial latency required. Document Number: 001-97964 Rev. *L Page 42 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Figure 30. DCARS Data Valid Timing[73, 74, 75, 76] CS# t CKHP tCSH tCSS CK ,CK# PSC , PSC# tPSCRWDS tDSZ RWDS tCKDI tCKD tDQLZ tDV tCKD Dn A DQ[7:0] tOZ Dn B Dn+1 A Dn+1 B RWDS and Data are driven by the memory Table 27. DCARS Read Timings (3.0 V)[77] Parameter 100 MHz Symbol HyperRAM PSC transition to RWDS transition Time delta between CK to DQ valid and PSC to RWDS Unit Min Max tPSCRWDS 1 7 ns tPSCRWDS - tCKD -1.0 +0.5 ns Note 77. Sampled, not 100% tested. Table 28. DCARS Read Timings (1.8 V)[78] Parameter HyperRAM PSC transition to RWDS transition Time delta between CK to DQ valid and PSC to RWDS Symbol 133 MHz 100 MHz Unit Min Max Min Max tPSCRWDS 1 5.5 1 5.5 ns tPSCRWDS - tCKD -1.0 +0.5 -1.0 +0.5 ns Note 78. Sampled, not 100% tested. Notes 73. This figure shows a closer view of the data transfer portion of Figure 27 on page 41 in order to more clearly show the Data Valid period as affected by clock jitter and clock to output delay uncertainty. 74. CK# and PSC# are only used on the 1.8 V device. The 3 V device uses a single ended CK and PSC input. 75. The delay (phase shift) from CK to PSC is controlled by the HyperBus master interface (Host) and is generally between 40 and 140 degrees in order to place the RWDS edge within the data valid window with sufficient set-up and hold time of data to RWDS. The requirements for data set-up and hold time to RWDS are determined by the HyperBus master interface design and are not addressed by the HyperBus slave timing parameters. 76. The HyperBus timing parameters of tCKD, and tCKDI define the beginning and end position of the data valid period. The tCKD and tCKDI values track together (vary by the same ratio) because RWDS and Data are outputs from the same device under the same voltage and temperature conditions. Document Number: 001-97964 Rev. *L Page 43 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 11. Ordering Information 11.1 Ordering Part Number The ordering part number is formed by a valid combination of the following: S27KS 064 1 DP B H I 02 0 Packing Type 0 = Tray 3 = 13" Tape and Reel Model Number (Additional Ordering Options) 02 = Standard 6 8 1.0 mm package (VAA024) 03 = DDR Center Aligned Read Strobe (DCARS) 6 8 1.0 mm package (VAA024) Temperature Range / Grade I = Industrial (-40 C to + 85 C) V = Industrial Plus (-40 C to + 105 C) A = Automotive, AEC-Q100 Grade 3 (-40 C to + 85 C) B = Automotive, AEC-Q100 Grade 2 (-40 C to + 105 C) Package Materials H = Low-Halogen, Lead (Pb)-free Package Type B = 24-ball FBGA, 1.00 mm pitch (5x5 ball footprint) Speed DA = 100 MHz DG = 133 MHz DP = 166 MHz Device Technology 1 = 63 nm DRAM Process Technology Density 064 = 64 Mb 128 = 128Mb Device Family S27KS, S70KS Cypress Memory 1.8 V-only, HyperRAM Self-refresh DRAM S27KL, S70KL Cypress Memory 3.0 V-only, HyperRAM Self-refresh DRAM Document Number: 001-97964 Rev. *L Page 44 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 11.2 Valid Combinations The Recommended Combinations table lists configurations planned to be available in volume. The table below will be updated as new combinations are released. Consult your local sales representative to confirm availability of specific combinations and to check on newly released combinations. Table 29. Valid Combinations -- Standard Device Family Density Technology Speed Package, Material and Temperature Model Number Packing Type Ordering Part Number Package Marking S27KL 064 1 DA BHI 02 0 S27KL0641DABHI020 7KL0641DAHI02 S27KL 064 1 DA BHI 02 3 S27KL0641DABHI023 7KL0641DAHI02 S27KL 064 1 DA BHV 02 0 S27KL0641DABHV020 7KL0641DAHV02 S27KL 064 1 DA BHV 02 3 S27KL0641DABHV023 7KL0641DAHV02 S70KL 128 1 DA BHI 02 0 S70KL1281DABHI020 7KL1281DAHI02 S70KL 128 1 DA BHI 02 3 S70KL1281DABHI023 7KL1281DAHI02 S70KL 128 1 DA BHV 02 0 S70KL1281DABHV020 7KL1281DAHV02 S70KL 128 1 DA BHV 02 3 S70KL1281DABHV023 7KL1281DAHV02 S27KS 064 1 DP BHI 02 0 S27KS0641DPBHI020 7KS0641DPHI02 S27KS 064 1 DP BHI 02 3 S27KS0641DPBHI023 7KS0641DPHI02 S27KS 064 1 DP BHV 02 0 S27KS0641DPBHV020 7KS0641DPHV02 S27KS 064 1 DP BHV 02 3 S27KS0641DPBHV023 7KS0641DPHV02 S70KS 128 1 DP BHI 02 0 S70KS1281DPBHI020 7KS1281DPHI02 S70KS 128 1 DP BHI 02 3 S70KS1281DPBHI023 7KS1281DPHI02 S70KS 128 1 DP BHV 02 0 S70KS1281DPBHV020 7KS1281DPHV02 S70KS 128 1 DP BHV 02 3 S70KS1281DPBHV023 7KS1281DPHV02 Document Number: 001-97964 Rev. *L Page 45 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 30. Valid Combinations -- DCARS Device Family Density Technology Speed Package, Material and Temperature Model Number Packing Type Ordering Part Number Package Marking S27KL 064 1 DA BHI 03 0 S27KL0641DABHI030 7KL0641DAHI03 S27KL 064 1 DA BHI 03 3 S27KL0641DABHI033 7KL0641DAHI03 S27KL 064 1 DA BHV 03 0 S27KL0641DABHV030 7KL0641DAHV03 S27KL 064 1 DA BHV 03 3 S27KL0641DABHV033 7KL0641DAHV03 S70KL 128 1 DA BHI 03 0 S70KL1281DABHI030 7KL1281DAHI03 S70KL 128 1 DA BHI 03 3 S70KL1281DABHI033 7KL1281DAHI03 S70KL 128 1 DA BHV 03 0 S70KL1281DABHV030 7KL1281DAHV03 S70KL 128 1 DA BHV 03 3 S70KL1281DABHV033 7KL1281DAHV03 S27KS 064 1 DA BHI 03 0 S27KS0641DABHI030 7KS0641DAHI03 S27KS 064 1 DA BHI 03 3 S27KS0641DABHI033 7KS0641DAHI03 S27KS 064 1 DA BHV 03 0 S27KS0641DABHV030 7KS0641DAHV03 S27KS 064 1 DA BHV 03 3 S27KS0641DABHV033 7KS0641DAHV03 S70KS 128 1 DA BHI 03 0 S70KS1281DABHI030 7KS1281DAHI03 S70KS 128 1 DA BHI 03 3 S70KS1281DABHI033 7KS1281DAHI03 S70KS 128 1 DA BHV 03 0 S70KS1281DABHV030 7KS1281DAHV03 S70KS 128 1 DA BHV 03 3 S70KS1281DABHV033 7KS1281DAHV03 S27KS 064 1 DG BHI 03 0 S27KS0641DGBHI030 7KS0641DGHI03 S27KS 064 1 DG BHI 03 3 S27KS0641DGBHI033 7KS0641DGHI03 S27KS 064 1 DG BHV 03 0 S27KS0641DGBHV030 7KS0641DGHV03 S27KS 064 1 DG BHV 03 3 S27KS0641DGBHV033 7KS0641DGHV03 S70KS 128 1 DG BHI 03 0 S70KS1281DGBHI030 7KS1281DGHI03 S70KS 128 1 DG BHI 03 3 S70KS1281DGBHI033 7KS1281DGHI03 S70KS 128 1 DG BHV 03 0 S70KS1281DGBHV030 7KS1281DGHV03 S70KS 128 1 DG BHV 03 3 S70KS1281DGBHV033 7KS1281DGHV03 Document Number: 001-97964 Rev. *L Page 46 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 11.3 Valid Combinations -- Automotive Grade / AEC-Q100 The table below lists configurations that are Automotive Grade / AEC-Q100 qualified and are planned to be available in volume. The table will be updated as new combinations are released. Consult your local sales representative to confirm availability of specific combinations and to check on newly released combinations. Production Part Approval Process (PPAP) support is only provided for AEC-Q100 grade products. Products to be used in end-use applications that require ISO/TS-16949 compliance must be AEC-Q100 grade products in combination with PPAP. Non-AEC-Q100 grade products are not manufactured or documented in full compliance with ISO/TS-16949 requirements. AEC-Q100 grade products are also offered without PPAP support for end-use applications that do not require ISO/TS-16949 compliance. Table 31. Valid Combinations -- Automotive Grade / AEC-Q100 Device Family Density Technology Speed Package, Material and Temperature Model Number Packing Type Ordering Part Number Package Marking S27KL 064 1 DA BHA 02 0 S27KL0641DABHA020 7KL0641DAHA02 S27KL 064 1 DA BHA 02 3 S27KL0641DABHA023 7KL0641DAHA02 S27KL 064 1 DA BHB 02 0 S27KL0641DABHB020 7KL0641DAHB02 S27KL 064 1 DA BHB 02 3 S27KL0641DABHB023 7KL0641DAHB02 S70KL 128 1 DA BHA 02 0 S70KL1281DABHA020 7KL1281DAHA02 S70KL 128 1 DA BHA 02 3 S70KL1281DABHA023 7KL1281DAHA02 S70KL 128 1 DA BHB 02 0 S70KL1281DABHB020 7KL1281DAHB02 S70KL 128 1 DA BHB 02 3 S70KL1281DABHB023 7KL1281DAHB02 S27KS 064 1 DP BHA 02 0 S27KS0641DPBHA020 7KS0641DPHA02 S27KS 064 1 DP BHA 02 3 S27KS0641DPBHA023 7KS0641DPHA02 S27KS 064 1 DP BHB 02 0 S27KS0641DPBHB020 7KS0641DPHB02 S27KS 064 1 DP BHB 02 3 S27KS0641DPBHB023 7KS0641DPHB02 S70KS 128 1 DP BHA 02 0 S70KS1281DPBHA020 7KS1281DPHA02 S70KS 128 1 DP BHA 02 3 S70KS1281DPBHA023 7KS1281DPHA02 S70KS 128 1 DP BHB 02 0 S70KS1281DPBHB020 7KS1281DPHB02 S70KS 128 1 DP BHB 02 3 S70KS1281DPBHB023 7KS1281DPHB02 Document Number: 001-97964 Rev. *L Page 47 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Table 32. Valid Combinations -- DCARS Automotive Grade / AEC-Q100 Device Family Density Technology Speed Package, Material and Temperature Model Number Packing Type Ordering Part Number Package Marking S27KL 064 1 DA BHA 03 0 S27KL0641DABHA030 7KL0641DAHA03 S27KL 064 1 DA BHA 03 3 S27KL0641DABHA033 7KL0641DAHA03 S27KL 064 1 DA BHB 03 0 S27KL0641DABHB030 7KL0641DAHB03 S27KL 064 1 DA BHB 03 3 S27KL0641DABHB033 7KL0641DAHB03 S70KL 128 1 DA BHA 03 0 S70KL1281DABHA030 7KL1281DAHA03 S70KL 128 1 DA BHA 03 3 S70KL1281DABHA033 7KL1281DAHA03 S70KL 128 1 DA BHB 03 0 S70KL1281DABHB030 7KL1281DAHB03 S70KL 128 1 DA BHB 03 3 S70KL1281DABHB033 7KL1281DAHB03 S27KS 064 1 DA BHA 03 0 S27KS0641DABHA030 7KS0641DAHA03 S27KS 064 1 DA BHA 03 3 S27KS0641DABHA033 7KS0641DAHA03 S27KS 064 1 DA BHB 03 0 S27KS0641DABHB030 7KS0641DAHB03 S27KS 064 1 DA BHB 03 3 S27KS0641DABHB033 7KS0641DAHB03 S70KS 128 1 DA BHA 03 0 S70KS1281DABHA030 7KS1281DAHA03 S70KS 128 1 DA BHA 03 3 S70KS1281DABHA033 7KS1281DAHA03 S70KS 128 1 DA BHB 03 0 S70KS1281DABHB030 7KS1281DAHB03 S70KS 128 1 DA BHB 03 3 S70KS1281DABHB033 7KS1281DAHB03 S27KS 064 1 DG BHA 03 0 S27KS0641DGBHA030 7KS0641DGHA03 S27KS 064 1 DG BHA 03 3 S27KS0641DGBHA033 7KS0641DGHA03 S27KS 064 1 DG BHB 03 0 S27KS0641DGBHB030 7KS0641DGHB03 S27KS 064 1 DG BHB 03 3 S27KS0641DGBHB033 7KS0641DGHB03 S70KS 128 1 DG BHA 03 0 S70KS1281DGBHA030 7KS1281DGHA03 S70KS 128 1 DG BHA 03 3 S70KS1281DGBHA033 7KS1281DGHA03 S70KS 128 1 DG BHB 03 0 S70KS1281DGBHB030 7KS1281DGHB03 S70KS 128 1 DG BHB 03 3 S70KS1281DGBHB033 7KS1281DGHB03 Document Number: 001-97964 Rev. *L Page 48 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 12. Revision History Document Title: S27KL0641/S27KS0641/S70KL1281/S70KS1281, 3.0 V/1.8 V, 64 Mb (8 MB)/128 Mb (16 MB), HyperRAMTM Self-Refresh DRAM Document Number: 001-97964 Rev. ECN No. Orig. of Change Submission Date Description of Change ** - MAMC 05/01/2015 Initial release. *A - MAMC 06/05/2015 Read Transactions: Maximum Operating Frequency For Latency Code Options table: updated `Latency Code' 0010 values Device Identification Registers: Updated `ID Register 1 Bit Assignments' table Electrical Specifications: Updated Ambient Temperature with Power Applied HyperRAM Hardware Interface: Updated the following: Power-On Reset: removed section Power Down: removed section DC Characteristics (CMOS Compatible) table: updated ICC5, ICC6I, and ICC6IP Test Conditions Electrical Specifications/Power Down: 1.8V Power-Down Voltage and Timing table: changed VRST and TPD MIn 3.0V Power-Down Voltage and Timing table: changed VRST and TPD MIn Key to Switching Waveforms: removed section AC Test Conditions: removed section AC Characteristics: updated section HyperBus Specification: Removed section. Refer to the HyperBus specification for all non-device specific information on the HyperBus interface. *B - MAMC 07/10/2015 Physical Interface: Updated section. Ordering Information: Updated Valid Combinations table. *C 4854266 MAMC 07/29/2015 Updated to Cypress template. *D 5041839 MAMC 12/08/2015 Updated Electrical Specifications: Updated DC Characteristics: Updated details of ILI parameter. Added values of IDPD parameter corresponding to "Test Condition" TA = 105C. *E 5155616 RYSU 03/01/2016 Added Errata. *F 5327405 SZZX 06/28/2016 Complete update. Removed Errata. *G 5430299 RYSU 09/08/2016 Changed status from "Advance" to "Final". Updated Electrical Specifications: Updated Operating Ranges: Updated Temperature Ranges: Added Automotive Grade. Updated Ordering Information: Added Valid Combinations -- Automotive Grade / AEC-Q100. Updated to new template. *H 5500343 SZZX 11/03/2016 Updated Electrical Specifications: Updated DC Characteristics: Updated Table 16. Updated Physical Interface: Updated Physical Diagrams: Updated Fortified Ball Grid Array 24-ball 6 x 8 x 1.0 mm (VAA024). Document Number: 001-97964 Rev. *L Page 49 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Document Title: S27KL0641/S27KS0641/S70KL1281/S70KS1281, 3.0 V/1.8 V, 64 Mb (8 MB)/128 Mb (16 MB), HyperRAMTM Self-Refresh DRAM Document Number: 001-97964 Rev. ECN No. Orig. of Change Submission Date *I 5560735 SZZX 12/20/2016 Updated Document Title to read as "S27KL0641/S27KS0641/S70KL1281/S70KS1281, 3.0 V/1.8 V, 64 Mb (8 MB)/128 Mb (16 MB), HyperRAMTM Self-Refresh DRAM". Added S70KL1281 and S70KS1281 part numbers related information in all instances across the document. Updated Performance Summary: Updated Maximum Current Consumption table. Added Block Diagram -- 128 Mb. Updated General Description: Updated description. Updated Product Overview: Updated description. Updated Memory Space: Updated Table 5. Updated Register Space: Updated Table 6. Updated Register Space Access: Updated Configuration Register 0: Updated Table 9. Updated Hybrid Burst: Added Note below Table 11. Updated Fixed Latency: Updated description. Updated Deep Power Down: Updated description. Updated Interface States: Updated description. Updated Electrical Specifications: Updated DC Characteristics: Updated Table 16. Updated HIGHCapacitance Characteristics: Updated Table 7.2. Updated Table 7.3. Updated Timing Specifications: Updated AC Characteristics: Updated Read Transactions: Updated Table 22. Updated Table 23. Added Figure 24. Updated Write Transactions: Added Figure 25. Updated Ordering Information: Updated Ordering Part Number: Added 128 Mb details. Updated Valid Combinations on page 45: Updated Table 29. Updated Table 30. Updated Valid Combinations -- Automotive Grade / AEC-Q100: Updated Table 31. Updated Table 32. *J 5688128 RUPA 04/10/2017 Updated Cypress logo. Updated Copyright. Description of Change *K 5844216 SZZX 08/04/2017 Updated KL/KS1281 DC parameters *L 6267725 MNAD 07/31/2018 Updated template. Added a note in Table 25. Document Number: 001-97964 Rev. *L Page 50 of 51 S27KL0641/S27KS0641 S70KL1281/S70KS1281 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC(R) Solutions Products (R) (R) Arm Cortex Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface cypress.com/clocks cypress.com/interface Internet of Things Memory cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs cypress.com/pmic Touch Sensing Cypress Developer Community Community | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/touch USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU cypress.com/usb cypress.com/wireless (c) Cypress Semiconductor Corporation, 2015-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress does not assume any liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 001-97964 Rev. *L Revised July 31, 2018 Page 51 of 51