6630B Series Single-Output, 80-100 W GPIB Power Supplies Data Sheet Speed and accuracy for test optimization * Fast, low-noise outputs * Programmable active down-programmer sinks the full rated current * Dual-range, precision low current measurement * Optional isolation and polarity reversal relays * Built-in measurements and advanced programmable features * Protection features to ensure DUT safety This series of linear-regulated 80-100 W DC power supplies is designed to maximize the throughput of DUTs through the manufacturing test process. Both programming and measurement are optimized for speed. The active downprogrammer can sink up to the full rated current of the power supply, which quickly brings the power supply output to zero volts. The 6630B series offers many advanced programmable features including stored states and status reporting. Programming is done using industry standard SCPI commands via the GPIB or RS-232. Test system integration is further simplified by using the VXIplug&play drivers. The optional relays simplify system design and troubleshooting. The optional front panel binding posts make the 6630B series convenient on the R&D lab bench. The built-in microamp measurement system helps the engineer to easily and accurately monitor the output voltage and current without a complicated test setup. Specifications Specifications (at 0 to 55 C unless other wise specified) 6631B 6632B 6633B 6634B Number of outputs 1 1 1 1 GPIB Yes Yes Yes Yes Output ratings Voltage 0 to 8 V 0 to 20 V 0 to 50 V 0 to 100 V Current 0 to 10 A 0 to 5 A 0 to 2 A 0 to 1 A 5 mV 10 mV 20 mV 50 mV 4 mA 2 mA 1 mA 0.5 mA Programming accuracy at 25 C 5 C Voltage +Current 0.05% + Ripple and noise 20 Hz to 20 MHz, with outputs ungrounded or with either terminal grounded Voltage normal mode rms peak-to-peak Fast mode rms 0.3 mV 0.5 mV 0.5 mV 3 mV 3 mV 3 mV 2 mV 1 mV 1 mV 1 mV 10 mV 10 mV 15 mV 25 mV rms 3 mA 2 mA 2 mA 2 mA peak-to-peak Current 0.3 mV 3 mV DC measurement accuracy via GPIB or front-panel meters with respect to actual output at 25 C 5 C Voltage 0.03% + 2 mV 3 mV 6 mV 12 mV Low current range -20 mA to +20 mA 0.1% + 2.5 A 2.5 A 2.5 A 2.5 A High current range +20 mA to + rated I 0.2% + 1 mA 0.5 mA 0.25 mA 0.25 mA -20 mA to - rated I 0.2% + 1.6 mA 1.1 mA 0.85 mA 0.85 mA Load regulation Voltage 2 mV 2 mV 4 mV 5 mV Current 2 mA 1 mA 1 mA 1 mA Voltage 0.5 mV 0.5 mV 1 mV 1 mV Current 1 mA 0.5 mA 0.25 mA 0.25 mA Line regulation Transient response time Less than 100 s (50 s in the fast mode) for the output voltage to recover to its previous level (within 0.1% of the voltage rating of the supply or 20 mV) following any step change in load current of up to 50% of the output current rating of the supply. Supplemental characteristics (Non-warranted characteristics determined by design and useful in applying the product) 6631B 6632B 6633B 6634B Average programming resolution Voltage 2 mV 5 mV 12.5 mV 25 mV Current 2.5 mA 1.25 mA 0.5 mA 0.25 mA 10 A 5A 2A 1A 0.4% + 4 mA 0.4% + 2 mA 0.4% +1 mA 0.4% + 5 mA Sink current Sink current tracking SCPI mode Compatibility mode Minimum current in constant current mode* * 2 When programming in the 6630A Series language compatibility mode -500 mA -250 mA -100 mA -50 mA 40 mA 20 mA 8 mA 4 mA Supplemental characteristics for all model numbers DC floating voltage: Output terminals can be floated up to 240 VDC maximum from chassis ground Remote sensing: Up to two volts dropped in each load lead. Add 2 mV to the voltage load regulation specification for each one volt change in the positive output lead due to load current change. Command processing time: Average time required for the output voltage to begin to change following receipt of digital data is 4 ms for the power supplies connected directly to the GPIB. (Display disabled). Output programming response time: The rise and fall time (10/90% and 90/10%) of the output voltage is less than 2 ms (400 s in fast mode). The output voltage change settles within 1 LSB (0.025% x rated voltage) of final value in less than 6 ms (2 ms in the fast mode). GPIB interface capabilities: IEEE-488.2, SCPI command set, and 6630A Series programming compatibility Input power (full load): 3.5 A, 250 W Regulatory compliance: Complies with EMC directive 89/336/EEC (ISM 1B). Size: 425.5 mm W x 88.1 mm H x 364.4 mm D (16.8 in x 3.5 in x 14.3 in) Weight: Net, 12.7 kg (28 lb) net; 15.0 kg (33 lb) shipping Warranty: One year Software driver: VXIplug&play Measurement time: Average time to make a voltage or current measurement is 50 ms. Agilent Models: 6631B, 6632B 6633B, 6634B Top 364.4 mm 14.3" Terminal Strip Detail Output 2 & 3 +S + - -S Screw Size: M35 x 0.6 88.1 mm 3.5" 100 mm 3.93" 425.4 mm 16.75" Side Rear 3 www.agilent.com www.agilent.com/find/6630 Ordering information Opt 100 87 to 106 VAC, 47 to 63 Hz Opt 120 104 to 127 VAC, 47 to 63 Hz Opt 220 191 to 233 VAC, 47 to 63 Hz Opt 230 207 to 253 VAC, 47 to 63 Hz Opt 020 Front-panel binding posts (N/A on 6631B) Opt 760 Isolation and reversal relays, only available at time of order (not available on the 6631B) Opt 8ZJ Removes feet for use in a racked system Opt 0L1 Full documentation on CD-ROM, and printed standard documentation package. CD-ROM includes User's Guide, Programming Guide, Service Manual and Quick Start Guide Opt 0B3 Service manual For more information on Agilent Technologies' products, applications or services, please contact your local Agilent office. The complete list is available at: www.agilent.com/find/contactus Agilent Advantage Services is committed to your success throughout your equipment's lifetime. To keep you competitive, we continually invest in tools and processes that speed up calibration and repair and reduce your cost of ownership. You can also use Infoline Web Services to manage equipment and services more effectively. By sharing our measurement and service expertise, we help you create the products that change our world. www.agilent.com/find/advantageservices Accessories p/n 1494-0060 Rack slide kit E3663AC Support rails for Agilent rack cabinets 1CM002A* Rack mount flange kit 88.1mm H (2U), two flange brackets: 1.75 inch hole spacing 1CP001A* Rack mount flange and handle kit 88.1 mm H (2U), two brackets and front handles Application notes 10 Practical Tips You Need to Know About Your Power Products, 5965-8239E 10 Hints for Using Your Power Supply to Decrease Test Time, 5968-6359E Understanding Linear Power Supply Operation (AN1554), 5989-2291EN * Support rails required www.agilent.com/quality Agilent Email Updates www.agilent.com/find/emailupdates Get the latest information on the products and applications you select. Agilent Channel Partners www.agilent.com/find/channelpartners Get the best of both worlds: Agilent's measurement expertise and product breadth, combined with channel partner convenience. Americas Canada Brazil Mexico United States (877) 894 4414 (11) 4197 3600 01800 5064 800 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 375 8100 Europe & Middle East Belgium 32 (0) 2 404 93 40 Denmark 45 45 80 12 15 Finland 358 (0) 10 855 2100 France 0825 010 700* *0.125 /minute Germany Ireland Israel Italy Netherlands Spain Sweden United Kingdom 49 (0) 7031 464 6333 1890 924 204 972-3-9288-504/544 39 02 92 60 8484 31 (0) 20 547 2111 34 (91) 631 3300 0200-88 22 55 44 (0) 118 927 6201 For other unlisted countries: www.agilent.com/find/contactus Revised: January 6, 2012 Product specifications and descriptions in this document subject to change without notice. (c) Agilent Technologies, Inc. 2012 Published in USA, January 26, 2012 5990-9303EN