1
notice_e-01
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2009. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
Should you have any question or inquiry on this matter, please contact our sales staff.
120
1
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
■ APPLICATIONS
■ IMPEDANCE-FREQUENCY CHARACTERISTICS
Measured by HP4291A
Please contact TAIYO YUDEN for further information in regard to other characteristics.
FL05RD / FL05R TYPE FL06BT TYPE
■ OPERATING TEMP.
filter01_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Use of high loss ferrite materials for excellent high frequency noise
absorption.
◦ High impedance for normal mode applications.
◦ 05 RD type available in taping for automatic insertion.
◦ 06 BT type is designed for high current applications (3A).
◦ Absorption of high frequency noise from digital equipment data lines.
WOUND TORROIDS AND BEADS
【FL-R / RD Type】
【FL-BT Type】
❶Type
FL Wound torroids
and beads
❶Type
FL Wound torroids and beads
❸Shape
R△Ring core,
with single wire lead
RD Ring core,
with case, pin type
△＝Blank space
❹Product classification code
04
❹Nominal inductance
(μH)
example
1R0 1.0
200 20.0
※R＝decimal point
❺Inductance tolerance
A Higher than normal value
E Special tolerance
❼Internal code
△Standard product
07 Product classification
code
△＝Blank space
❺Internal code
△Standard product
△＝Blank space
❻Packaging
△Bulk
T Tape & Reel
Z Ammo
ーSpecial code
△＝Blank space
❸Shape
BT Cylinder,
porous core
❷Dimensions of core
05 4.8mm
❷Dimensions of core
(diameter)
06 6.0mm
F L 0 5 R D 2 0 0 A T ○
❶ ❷ ❸ ❹ ❺ ❻ ❼
F L 0 6 B T 0 4 ○
❶❷❸❹❺
Type 〔05RD〕 〔05R〕 〔06BT04〕
Fig.
Minimum
Quantity
(pcs.)
Bulk 400 500 250
Tape & Reel 2000 ー ー
Ammo 1500 ー ー
Unit : mm (inch)
＋0.6
ー0.2
9.0max
（0.35max）
3.7max
（0.146max）
φ0.6
（φ0.024）
9.0max
（0.351max）
4.0±1
（0.157±0.039）
5.0
（0.197 ）
＋0.024
ー0.008
6.5max
（0.256max）
3.0max
（0.118max）
φ0.3
（φ0.012）
φ6.0±0.2
（φ0.24±0.008）
15.2max
（0.598max）
WAV E
◦ ー25℃～105℃（Including self-generated heat）
FERRITE PRODUCTS
121
1
■ PART NUMBERS
filter01_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Impedance
〔Ω〕 (typical)
DC Resistance
〔Ω〕 (max)
Rated current
〔A〕 (max)
FL05RD 1R0E□RoHS 1.0＋1.0
－0.5 800 (at 400MHz) 0.08 0.5
FL05R 100A RoHS 10 min. 900 (at 200MHz) 0.05
1.5
FL05RD 100A□RoHS
FL05R 200A－07 RoHS 20 min. 2000 (at 100MHz) 0.08
FL05RD 200A□RoHS
FL06BT 04 RoHS ー 1000 (at 150MHz) 0.05 3.0
□Please specify the packaging code (T : Tape & reel, Z : ammo, Blank space : bulk)
1
filter01_pack-P1 filter01_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦FL05RD
①Minimum Quantity
Type Minimum Quantity (pcs.)
Bulk Tape & Reel Ammo
FL05R 500 ー ー
FL05RD 400 2000 1500
FL06BT 250 ー ー
②Taping dimensions
Type Symbol Dimension
FL05RD
D1 9.0 max. (0.354 max.)
H2 9.0 max. (0.354 max.)
T 3.7 max. (0.146 max.)
H1 31.0 max. (1.22 max.)
H 18.0±1.0 (0.709±0.039)
P 12.7±1.0 (0.500±0.039)
P0 12.7±0.3 (0.500±0.012) ※1
P1 3.85±0.8 (0.152±0.031)
P2 6.35±1.3 (0.250±0.051)
W1 9.0＋0.75
ー0.5 (0.354＋0.030
ー0.020)
F 5.0＋0.6
ー0.2 (0.197＋0.024
ー0.008)
d φ0.6 (φ0.024)
△h 0±2.0 (0±0.079)
W 18.0＋1.0
ー0.5 (0.709＋0.024
ー0.008)
W0 12.5 min. (0.492 min.)
W2 3.0 min. (0.118 min.) ※2
ℓ 0 max. (0 max.)
D0 4.0±0.3 (0.157±0.012)
L 11.0 max. (0.433 max.)
t 0.7±0.2 (0.028±0.008)
◦FL05RD
③Reel size
60 or less〔53〕
（2.362 or less〔2.087〕）
Unit : mm (inch)
Dimensions in parenthesis are measured value.
※1 Accumulated error for 20 pitches shall be within ±2mm.
※2 Pasting tape shall not exceed paste board.
Unit : mm (inch)
1
le0104fi01_reli-RP1 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating temperature Range
LA Type
ー25〜＋105℃CAL45 Type
LHL□□□
FBA/FBR ー25〜＋85℃
FL05□ Type ー25〜＋105℃
FL06BT Type
【Test Method and Remarks】
LA・CA・FL : Including self-generated heat
LHL□□□ : Including self-generated heat
3. Rated current
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : The maximum DC value having inductance within 10% and temperature incease within 40℃ (LA:20℃) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25℃ (LHL08, LHL10, LHL13)
: 30℃ (LHL16, LHLP□□)
: 40℃ (LHLC08, LHLC10)
FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
FL : The maximum DC value having temperature rise within specified value.
5. Inductance
LA Type
Within the specified toleranceCAL45 Type
LHL□□□
FBA/FBR
FL05□ Type Within the specified tolerance
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1KHz)
Measuring frequency : Specified frequency
FL05R□ : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
2. Storage temperature Range
LA Type
ー40〜＋85℃
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR Within the specified tolerance
FL05□ Type
FL06BT Type Refer to individual specification
【Test Method and Remarks】
FB : Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
1
le0104fi01_reli-RP2
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11. Over current
LA Type No emission of smoke no firing.
CAL45 Type
LHL□□□There shall be no scorch or short of wire.
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□/LA・CAL45 Type： Measuring current : Rated current×2
Duration : 5 min.
Number of measuring : one time
8. Self resonance frequency
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type △L/L : Within ±5%
CAL45 Type
LHL□□□ △L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Change of maximum inductance deviation in step 1 to 5
Step Temperature (℃)
1 20
2ー25 (Minimum operating temperature)
3 20 (Standard temperature)
4＋85 (Maximum operating temperature)
5 20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20℃
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20℃ (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20℃
10. Terminal strength : tensile force
LA Type
No abnormality such as cut lead, or looseness.CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cut lead, or looseness.
FL05□ Type No abnormality such as cut lead, or looseness.
FL06BT Type
【Test Method and Remarks】
LA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
25 5
CA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
10 10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm) force (N) duration (s)
0.3＜φd≦0.5 5
30±50.5＜φd≦0.8 10
0.8＜φd≦1.2 25
FBA/FBR : A bead shall be fixed and static loaded 20±1N (2.0±0.1 kgf) in axial direction of lead wire in 10±1 seconds.
FL05R□ : Fix the component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
7. DC Resisitance
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB・FL : Measuring equipment : DC ohmmeter
1
le0104fi01_reli-RP3 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
12. Terminal strength : bending
LA Type
No abnormality such as cut lead, or looseness.
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec-
ond bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.5＜φd≦0.8 5 0.50
LH・FB : Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec- : Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec-: Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec- Suspend a mass at the end the terminal, incline the body though angel of 90 and return it to initial position. This operation is done over a period of 2-3 sec. Then sec-
ond bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.5
0.8＜φd≦1.2 10 1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□100MΩ min.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Applied voltage : 500 VDC
Duration : 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR 1MΩ min. (Other than materail code MA)
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FBA・FBR : Applied voltage : 100 VDC
Duration : 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□No abnormality such as insulation damage
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration : 60 sec.
16. DC bias characteristic
LA Type △L/L : Within ー10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cracks on body.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Applied force : 30N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
FBA : Applied force : 50±3N
Duration : 30±1 sec.
1
le0104fi01_reli-RP4
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
18. Resisitance to vibration
LA Type △L/L : Within ±5% Q : 30min
CAL45 Type △L/L : Within ±5%
LHL□□□ Appearance : No abnomality △L/L : Within ±5% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR Appearance : No abnomality Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB ： Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type At least 75％ of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□At least 75％ of terminal electrode is covered by new solder.
FBA/FBR At least 90％ of terminal electrode is covered by new solder.
FL05□ Type At least 75％ of terminal electrode is covered by new solder.
FL06BT Type
【Test Method and Remarks】
LA, CA : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 1.5mm from bottom of case.
FB : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
FL05R□ : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 2 to 2.5mm from terminal root.
FL06BT : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type No significant abnormality in appearance
CAL45 Type △L/L : Within ±5%
LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only △L/L)
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type No significant abnormality in appearance Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Solder temperature : (CA) 270±5℃, (LA) 260±5℃
Duration : 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5℃
Duration : 10±1 sec.
Up to 1.5mm from bottom of case.
Manual soldering : Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration : 5±1 sec.
Up to 1.5mm from bottom of case.
Caution : No excessive pressing shall be applied to terminald.
Recovery : 4 to 24hrs of recovery under the standard condition after the test.
FB : Solder bath method : Condition 1 : Solder temperature : 260±5℃
Duration : 10±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
FL : Solder condition : 260±5℃ 10±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
1
le0104fi01_reli-RP5 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
22. Resisitance to solvent
LA Type Please avoid the ultrasonic cleaning of this product.
CAL45 Type
LHL□□□
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB : Solvent temperature : 20〜25℃
Duration : 30±5 sec.
Solvent type : Acetone, trichloroethylene
Recovery : 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP：only △L/L)
FBA/FBR Appearance : No abnormality Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Conditions for 1cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□□・FB : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1 Minimum operating temperature＋0
ー330±3
2 Room temperature Within 3
3 Minimum operating temperature＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles 〔LHL□□□〕
: 5 cycles (FBA, FBR)
Recovery : 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type △L/L : Within ±10% Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR Appearance：No abnormality Impedance change：Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90〜95%RH
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2℃
Humidity : 90〜95%RH
Duration : 1000 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
le0104fi01_reli-RP6
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
25. Loading under damp heat
LA Type △L/L : Within ±10% Q : ±30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Imductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90〜95%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : 40±2℃
Humidity : 90〜95%RH
Duration : 1000±24 hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 60±3℃
Humidity : 90〜95%RH
Duration : 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type △L/L : Within ±10% Q : ±30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 85±2℃
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type △L/L : Within ±10% Q : ±30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : ー25±2℃
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : ー40±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : ー40±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
LA Type
CAL45 Type
LHL□□□Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LHL□□□ : Temperature : 105±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 85±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
le0104fi01_reli-RP7 le0104fi01_reli_e-01
■ PRECAUTIONS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Design
1. Please design insertion pitches of a base in the pitches that fitted a terminal interval.
Technical
consider-
ations
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire Inductors in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
consider-
ations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical
consider-
ations
◆Cleaning conditions
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
Technical
consider-
ations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead route turns by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
・Ambient temperature 0〜40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
CAL Type, LH Type, FB Type, FL Type, LA Type
138
1
coil01_e-01
■ FEATURES
■ ORDERING CODE
■ APPLICATIONS
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ CM01 Series is Wire-wound Structured Type Commom Mode Choke
Coil which provides highly effective noise suppression characteristics
without distorting the wave pattern of High-speed Differential Signal
interface.
◦ Developed 1210 case-size by utilizing our wire-wound technologies.
This small and wire-wound structured product has little transmission
loss and keeps high common impedance up to GHz range.
◦ CM01S600 : Suitable characteristics for super high speed differential sig-
nal such as USB3.0 and so on. Cutoff frequency is 10GHz.
◦ CM01H900 : Suitable characteristics for high speed differential signal
such as HDMI, DVI, Displayport and so on. Cut-off frequency is 8GHz.
◦ CM01U900 : Suitable characteristics for differential signal such as
USB2.0, LVDS, LAN and so on. Cut-off frequency is 3GHz. High rated
current of this product makes it possible to replace 2012 size product
for this product.
◦ CM01U161 : Suitable characteristics for differential signal such as
USB2.0, LVDS, LAN and so on. Cut-off frequency is 3GHz. High com-
mon impedance of this product works effectively on noise suppression.
◦ Radiated noise suppression in the High-speed Diffrential Signal inter-
faces [HDMI, Serial-ATA, IEEE1394, LVDS, and USB2.0] of LCD-TV,
Blu-ray players, and PCs.
◦ Countermeasure for degradation of receiver sensitivity caused by
high frequency noise from high-speed differential signal of Cellular
phones, Data Cards and Smartphones.
◦ Common mode noise suppression raised from the power line and au-
dio signal in a small device.
COMMON MODE CHOKE COIL (SMD) FOR HIGH-SPEED DIFFERENTIAL SIGNAL
❶Type
CM Common mode choke coil
❹Impedance
600 60Ω typical at 100MHz
900 90Ω typical at 100MHz
161 160Ω typical at 100MHz
❺Packaging
T Taping
❷External Dimensions (L×W)
01 1.2×1.0mm
C M 0 1 H 9 0 0 T
❶❷❸❹❺
❸Product classification code
S USB3.0 correspondence
H HDMI/Displayport correspondence
U
USB2.0/LAN
correspondence
Ordering EHS No. of Lines Common Impedance
[Ω] (at 100MHz)
DC resistance
[Ω]
Rated current
[mA]
Rated voltage
［V］ (D.C.)
dielectric
resistance
［MΩ］
Cut off frequency
［GHz］
Characteristic
impedance
［Ω］
CM01S60 0T RoHs 2 60typ. 43min．0.4max．300max．20max．100min．10.0typ. 90typ.
CM01H90 0T RoHS 2 90typ. 65min. 0.5max. 280max. 20max. 100min. 8.0typ. 100typ.
CM01U90 0T RoHs 2 90typ. 65min．0.3max．400max．20max．100min．3.0typ. －
CM01U161T RoHs 2 160typ. 120min．0.6max．260max．20max．100min．3.0typ. －
REFLOW
Type Minimum Quantity (pcs.)
Embossed tape
CM01［2 Lines］ type 3000
0.35±0.10.30±0.1
1.2±0.2
0.03min.
1.0±0.20.9 max.
0.35±0.10.35±0.1
EQUIVALENT CIRCUIT
There is no directionality.
Unit：mm （inch）
■ PART NUMBERS
●CM01 TYPE
●CM01TYPE
FERRITE PRODUCTS
139
1
coil01_e-01
■ ELECTRICAL CHARACTERISTICS
1000
100
10
1
CM01 S600 Ty pe
10 100 1000 10000
Impedance〔Ω〕
Frequency〔MHz〕
Common Impedance
Differential Impedance
1000
100
10
1
CM01 H900 Ty pe
10 100 1000 10000
Impedance〔Ω〕
Frequency〔MHz〕
Common Impedance
Differential Impedance
1000
100
10
1
CM01 U900 Ty pe
10 100 1000 10000
Impedance〔Ω〕
Frequency〔MHz〕
Common Impedance
Differential Impedance
1000
100
10
1
CM01 U161 Ty pe
10 100 1000 10000
Impedance〔Ω〕
Frequency〔MHz〕
Common Impedance
Differential Impedance
0
−2
−4
−6
−8
−10
CM01 S600 Ty pe
10 100 1000 10000
sdd21〔ｄＢ〕
Frequency〔MHz〕
0
−2
−4
−6
−8
−10
CM01 H900 Ty pe
10 100 1000 10000
sdd21〔ｄＢ〕
Frequency〔MHz〕
0
−2
−4
−6
−8
−10
CM01 U900 Ty pe
10 100 1000 10000
sdd21〔ｄＢ〕
Frequency〔MHz〕
0
−2
−4
−6
−8
−10
CM01 U161 Ty pe
10 100 1000 10000
sdd21〔ｄＢ〕
Frequency〔MHz〕
■
Impedance characteristics
■
Transmission characteristic
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
140
1
coil02_e-01
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
■ APPLICATIONS
■ OPERATING TEMP.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Available in embossed tape and reel.
◦ Highly coupled coil construction ideal for common mode noise at-
tenuation.
◦ Immunity against undesirable external line radiation fields and broad-
cast waves generated by multifunction telephone sets, PBXs, and
facsimile machines.
◦ Preventive measure against DC line noise in electronic equipment.
◦ Suppresses radiated emissions from secondary power supplies and
signal lines on AC adapters, battery chargers, and digital equipment.
◦ Excellent for reducing radiated noise in DVC (digital video cameras)
and DSC (digital still cameras)
◦ Offers high speed differential mode noise attenuation in USB and
IEEE1394 connectors in personal computers, printers, scanners and
other computer peripherals.
❶Type
CM Common mode
choke coils
BU
❹Product classification code
01～10
❺Packaging
T Taped products
❻Internal code
△Standard Products
△＝Blank space
❷Dimensions of Core (mm)
04 3.5
05 5.0
❸Shape
RC Surface mount type
MC
C M 0 4 R C 0 1 T ○
❶ ❷ ❸ ❹ ❺ ❻
BU05MC 〔2 Lines〕 type BU05MC 〔3 Lines〕 type CM04RC 〔2 Lines〕 type
2.6±0.2
（0.102±0.008）
3.0±0.2
（0.118±0.008）
5.0±0.3
（0.197±0.012）
5.3±0.5
（0.209±0.020）
（0.5）
（0.020）
（0.2）
（0.008）
（0.5）
（0.020）
0.1min）
（0.004min）
2.7±0.2
（0.106±0.008）
2.6±0.2
（0.102±0.008）
1.5±0.2
（0.059±0.008）
5.0±0.3
（0.196±0.012）
5.3±0.5
（0.209±0.020）
（0.5）
（0.020）
（0.2）
（0.008）
（0.5）
（0.020）
0.1min）
（0.004min）
2.7±0.2
（0.106±0.008）
■ PART NUMBERS
Ordering code
EHS (
Environmental
Hazardous
Substances
)
No. of Lines Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] (D.C.)
Insulation
resistance
[MΩ] (min.)
CM04RC01T RoHS
2
800 (at 100MHz) 0.06 1.5
50 100
CM04RC04T RoHS 900 (at 20MHz) 0.1 1.3
CM04RC07T RoHS 500 (at 160MHz) 0.06 2.5
CM04RC09T RoHS 270 (at 200MHz) 0.03 3.0
CM04RC10T RoHS 100 (at 200MHz) 0.02 4.0
CM04RC02T RoHS 3 1000 (at 100MHz) 0.18 0.5
CM04RC08T (THIN) RoHS 1000 (at 200MHz) 0.2 0.5
CM04RC05T RoHS 4 800 (at 100MHz) 0.2 0.5
Ordering code
EHS (
Environmental
Hazardous
Substances
)
No. of Lines Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] (D.C.)
Insulation
resistance
[MΩ] (min.)
BU05MC01T RoHS 2 1000 (at 60MHz) 0.12 1 50 100
BU05MC08T RoHS 3 700 (at 60MHz) 0.11 0.5
●CM04RC Type
●BU05MC Type
CM04RC 〔3 Lines〕 type CM04RC 〔3 Lines〕 type （Thin）CM04RC 〔4 Lines〕 type
6.0±0.2
（0.236±0.008）
9.0±0.5
（0.354±0.020）
（1.3）
（0.051）
（0.25）
（0.010）
2.54±0.25
（0.100±0.010）
7.4±0.2
（0.291±0.008）
（0.5）
（0.020）
0.1min）
（0.004min）
4.3±0.3
（0.169±0.012）
6.0±0.2
（0.024±0.008）
9.0±0.5
（0.354±0.020）
（0.5）
（0.020）
（0.3）
（0.012）
1.27±0.25
（0.050±0.010）
5.3±0.2
（0.208±0.008）
（0.5）
（0.020）
0.1min）
（0.004min）
2.5±0.3
（0.100±0.012）
6.0±0.2
（0.236±0.008）
9.0±0.5
（0.354±0.020）
（1.3）
（0.051）
（0.25）
（0.010）
2.54±0.25
（0.100±0.010）
9.8±0.2
（0.354±0.008）
（0.5）
（0.020）
0.1min）
（0.004min）
4.1±0.3
（0.161±0.012）
The values without tolerance are for reference only. Unit : mm (inch)
6.0±0.2
（0.236±0.008）
9.0±0.5
（0.354±0.020）
（1.3）
（0.05）
（0.25）
（0.010）
2.54±0.25
（0.100±0.010）
5.2±0.2
（0.205±0.008）
（0.6）
（0.024）
0.1min
（0.004min）
4.4±0.3
（0.173±0.012）
Minimum Quantity (pcs.)
Embossed tape
2500
Minimum Quantity (pcs.)
Embossed tape
1500
Minimum Quantity (pcs.)
Embossed tape
1000
Minimum Quantity (pcs.)
Embossed tape
2500
Minimum Quantity (pcs.)
Embossed tape
1000
Minimum Quantity (pcs.)
Embossed tape
2500
COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) SMD TYPE
REFLOW
◦ ー25℃～105℃（Including self-generated heat）
FERRITE PRODUCTS
141
1
coil02_e-01
■ ELECTRICAL CHARACTERISTICS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
（Measured by HP4291A）
■
Impedance -vs- Frequency characteristics
RC07
RC09
RC10
RC01
RC04
Common mode
Normal mode
1
coil0102_pack-P1
coil0102_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
①Minimum Quantity
Type Minimum Quantity (pcs.)
Embossed tape
CM01 ［2 Lines］ type 3000
CM04RC ［2 Lines］ type 1500
CM04RC ［3 Lines］ type 1000
CM04RC ［3 Lines］ type (Thin) 2500
CM04RC ［4 Lines］ type 1000
BU05MC ［2 Lines］ type 2500
BU05MC ［3 Lines］ type 2500
②Tape Material
③Leader and Blank Portion
Type A B C
CM01 φ60＋1/－0φ180＋0/－3 10.0±1.5
(φ2.36＋0.039/－0) (φ7.09＋0/－0.118) (0.394±0.059)
CM04RC φ100±1φ330±2 18±1.5
(φ3.94±0.039) (φ12.99±0.079) (0.709±0.059)
BU05MC φ80±1φ330±2 13.5±1
(φ3.15±0.039) (φ12.99±0.079) (0.53±0.039)
Unit : mm (inch)
Type Lines Insertion
pitch
Chip cavity tape thickness
A B K T
CM01 2 4.0±0.1 1.16±0.1 1.41±0.1 0.98±0.1 0.3max.
CM04RC
2 8.0±0.1 5.7±0.1 9.65±0.1 5.2max 0.4±0.05
3 12.0±0.1 9.8±0.1 7.7±0.1 5.0max 0.38±0.05
3 (THIN) 8.0±0.1 5.7±0.1 9.8±0.1 3.1max 0.4±0.05
4 12.0±0.1 10.3±0.1 10.3±0.1 5.0max 0.3±0.05
BU05MC 28.0±0.1 5.35±1.5 5.7±0.2 3.2±0.1 0.4±0.05
3
Unit : mm (inch)
Type Leader Blank portions
(Leader side)
Blank portions
(Chip cavity side)
CM01 200～400 160～200 160 (6.30) or more
(7.87～15.75) (6.30～7.87)
CM04RC 150 (5.89) 80 (3.14) 80 (3.14)
BU05MC 150 (5.89) 80 (3.14) 80 (3.14)
Unit : mm (inch)
④Reel size
⑤Taping dimensions
◦Embossed tape (CM01 type)
◦Embossed tape (CM04RC type) 8mm pitch (0.31 inches pitch)
◦Embossed tape (CM04RC type) 12mm pitch (0.472 inches pitch)
◦Embossed tape (BU05MC type)
Unit : mm (inch)
⑥Top Tape Strength
◦CM01
The top tape requires a peel-off force of 0.1 to 1.0N in the direction of the arrow
as illutrated above.
◦CM04RC, BU05MC
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow
as illutrated above.
Unit : mm (inch)
Unit : mm (inch)
Unit
: mm (inch)
142
1
■ FEATURES
■ ORDERING CODE
■ APPLICATIONS
TLF Type ー25℃～＋105℃
CM Type ー25℃～＋105℃
（Including self-generated heat）
■ OPERATING TEMP.
coil03_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Highly reliable, compact and lightweight
◦ Easily inserted into the PCB
◦ TLF Type :
Countermeasure for noise in the low-frequency (AM) broad-casting
band. Shields against radiated emissions in the broadcasting fre-
quency for multi-functional telephone sets. PBXs, faxes, etc.
◦ CM/BU Type :
Countermeasure for noise in the high-frequency (MHz) band
COMMON MODE CHOKE COILS (FOR DC AND SIGNAL LINES) LEADED TYPE
【TLF Type】
【CM-BU Type】
❶Type
TLF Line filter
❶Type
CM Common mode choke coile
BU
❹Product classification code
01～20
❹Nominal inductance (μH)
example
302 3000
203 20000
❻❼Internal code
△△ Standard product
△＝Blank space
❺Internal code
△Standard product
△＝Blank space
❸Shape
UB△U core,
vertically split wound
UBH U core,
horizontally split wound
△＝Blank space
❸Shape
RA Double-wire lead
RBPin type with base
❷Dimensions of core
△9 9mm
△＝Blank space
❷Core dimensions （mm）
05 4.8
08 8.0
12 12.0
T L F △9 U B H 3 0 2 W ○ ○
❶ ❷ ❸ ❹ ❺ ❻ ❼
C M 0 5 R A 0 6 ○
❶❷❸❹❺
❺Inductance tolerance (%)
W＋100
ー10
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
TLF9UB Type TLF9UB H Type CM□□RA Type / BU08RA Type
CM05RB (2Lines Type) CM08RB (2Lines) Type CM08RB (4Lines) Type
Unit : mm (inch)
Type W (max.) T (max.)
CM05 6.5 (0.256) 3.0 (0.118)
CM08,BU08 11.0 (0.433) 6.0, 7.0 (0.024, 0.276)
CM12 15.5 (0.610) 7.0 (0.276)
Minimum Quantity (pcs.)
Box
500
Minimum Quantity (pcs.)
Box
500
Minimum Quantity (pcs.)
Box Bulk
1000 ー
Minimum Quantity (pcs.)
Box Bulk
500 ー
Minimum Quantity (pcs.)
Box Bulk
500 ー
Type
Minimum Quantity
(pcs.)
Box Bulk
CM05RA06
ー500
CM08RA□□
ー250
CM12RA02
ー100
BU08RA□□
ー200
WAV E
FERRITE PRODUCTS
143
1
■ PART NUMBERS
■ ELECTRICAL CHARACTERISTICS
coil03_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Ordering code
EHS (
Environmental
Hazardous
Substances
)
No. of lines Inductance
[μH] [
＋100
ー10 %]
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] D.C.
Insulation
resistance
[MΩ] (min.)
Impedance [KΩ]
(Reference values)
TLF9UBH 302W RoHS
2
3000 1.5 0.4
50 100
≧20 (at 1MHz)
TLF9UB 302W RoHS
TLF9UBH 802W RoHS 8000 3.0 0.3 ≧40 (at 700kHz)
TLF9UB 802W RoHS
TLF9UBH 20 3W RoHS 20000 6.5 0.18 ≧150 (at 500kHz)
TLF9UB 203W RoHS
Ordering code
EHS (
Environmental
Hazardous
Substances
)
No.of lines Inductance
[μH] [at 1kHz]
Impedance
[Ω] (typical)
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] D.C.
Insulation
resistance
[MΩ] (min.)
CM05RA 06 RoHS
2
0.7 min. 700 (at 200MHz) 0.050 1.5
50 100
BU08RA 11 RoHS 0.7～1.3 1000 (at 250MHz) 0.013 4.0
16 RoHS 1.19～2.21 1200 (at 200MHz) 0.011 3.0
CM08RA 17 RoHS 15.0 min. 2000 (at 80MHz) 0.040 2.4
20 RoHS 6.0 min. 500 (at 200MHz) 0.020 5.5
CM12R A 02 RoHS 10.0 min. 2000 (at 80MHz) 0.040 3.0
CM05RB 01 RoHS 7.0 min. 700 (at 70MHz) 0.050 2.0
03 RoHS 15.0 min. 1400 (at 100MHz) 0.060 1.5
CM08RB
01 RoHS 40.0 min. 2500 (at 30MHz) 0.040 2.0
02 RoHS 15.0 min. 2000 (at 50MHz) 0.040 2.4
04 RoHS 110.0 min. 2000 (at 70MHz) 0.040 3.0
05 RoHS 6.0 min. 450 (at 100MHz) 0.020 4.0
03 RoHS 4 15.0 min. 1000 (at 50MHz) 0.050 2.0
203
802
302
Measuring conditions
Equipment : HP4291A Vosc : 0.5V (CM/BU type)
HP4192A Vosc : 0.35V (TLF type)
Measuring circuit :
To impedance analyzer
144
1
coil04_e-01
■ FEATURES ■ APPLICATIONS
TLF9U Type ー25℃～＋105℃
TLF14CB Type ー25℃～＋105℃
（Including self-generated heat）
■ OPERATING TEMP.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ TLF 9UA (H) Type : Small-sized configuration
◦ TLF14CB (H) Type : Ordinary configuration
◦ As a preventive measure against noise terminal voltage or power
supply noise in TV or VTR units, SW power supplies, NC machines,
computer systems, peripheral units, measuring instruments, and con-
trollers.
◦ TLF 9UA (H) Type : low-current applications
◦ TLF14CB (H) Type :
equipment with several tens of watts of input power
COMMON MODE CHOKE COILS (FOR AC LINES) LEADED TYPE
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
TLF14CB Type TLF14CBH Type
TLF9UA Type TLF9UA H Type
Unit : mm (inch)
■ ORDERING CODE
❶Type
TLF Line filter
❺Inductance tolerance (%)
△Nominal Values or higher
W＋100
ー10
△＝Blank space
❽Internal code
△Standard Product
△＝Blank space
❻Rated current (A)
R54 0.54
0R8 0.8
※R=decimal point
❼Product classification code
△Standard
△＝Blank space
❸Shape
UA△U core, vertical type
UAH U core, horizontal type
CB△Square type core vertically split wound
CBH Square type core horizontally split wound
△＝Blank space
❷Core dimensions （mm）
△9 9
14 14
△＝Blank space
T L F △9 U A H 1 0 2 W 0 R 8 ○ ○
❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽
❹Nominal Inductance (μH)
example
102 1000
103 10000
Type Minimum Quantity (pcs.)
Box
TLF9UA□500
TLF14CB□500
WAV E
FERRITE PRODUCTS
145
1
coil04_e-01
■ PART NUMBERS
■ ELECTRICAL CHARACTERISTICS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Type Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[mH]
Inductance
Tolerance
DC resistance
[Ω] (max.)
Rated current
[A] (max.)
Rated voltage
[V] （max.）
Withstanding
voltage
［V］ （min.）
[1 minute]
Applicable
frequency
[MHz]
Reference Value
TLF9UA
TLF 9UA 102 W 0R8 RoHS 1 ＋100％/ー10％0.5 0.80
AC250 AC2000 0.1～10
TLF 9UA 202 W R54 RoHS 2 ＋100％/ー10％1.0 0.54
TLF 9UA 302 W R42 RoHS 3 ＋100％/ー10％1.5 0.42
TLF 9UA 502 W R32 RoHS 5 ＋100％/ー10％2.5 0.32
TLF 9UA 802 W R25 RoHS 8 ＋100％/ー10％4.0 0.25
TLF 9UA 103 W R23 RoHS 10＋100％/ー10％4.5 0.23
TLF9UAH
TLF 9UA H 102 W 0R8 RoHS 1 ＋100％/ー10％0.5 0.80
TLF 9UA H 202 W R54 RoHS 2 ＋100％/ー10％1.0 0.54
TLF 9UA H 302 W R42 RoHS 3 ＋100％/ー10％1.5 0.42
TLF 9UA H 502 W R32 RoHS 5 ＋100％/ー10％2.5 0.32
TLF 9UA H 802 W R25 RoHS 8 ＋100％/ー10％4.0 0.25
TLF 9UA H 103 W R23 RoHS 10＋100％/ー10％4.5 0.23
TLF14CB
TLF 14CB 102 1R5 RoHS 1.0 min 0.1 1.5
TLF 14CB 222 1R2 RoHS 2.2 min 0.18 1.2
TLF 14CB 332 1R0 RoHS 3.3 min 0.32 1.0
TLF 14CB 472 1R0 RoHS 4.7 min 0.38 1.0
TLF 14CB 562 0R8 RoHS 5.6 min 0.42 0.8
TLF 14CB 682 0R8 RoHS 6.8 min 0.6 0.8
TLF 14CB 103 0R7 RoHS 10 min 0.85 0.7
TLF 14CB 223 0R4 RoHS 22 min 1.7 0.4
TLF 14CB 333 0R3 RoHS 33 min 2.7 0.3
TLF 14CB 473 0R2 RoHS 47 min 3.6 0.2
TLF 14CB 563 0R2 RoHS 56 min 5 0.2
TLF 14CB 683 0R2 RoHS 68 min 6.5 0.2
TLF14CBH
TLF 14CB H 102 1R5 RoHS 1.0 min 0.1 1.5
TLF 14CB H 222 1R2 RoHS 2.2 min 0.18 1.2
TLF 14CB H 332 1R0 RoHS 3.3 min 0.32 1.0
TLF 14CB H 472 1R0 RoHS 4.7 min 0.38 1.0
TLF 14CB H 562 0R8 RoHS 5.6 min 0.42 0.8
TLF 14CB H 682 0R8 RoHS 6.8 min 0.6 0.8
TLF 14CB H 103 0R7 RoHS 10 min 0.85 0.7
TLF 14CB H 223 0R4 RoHS 22 min 1.7 0.4
TLF 14CB H 333 0R3 RoHS 33 min 2.7 0.3
TLF 14CB H 473 0R2 RoHS 47 min 3.6 0.2
TLF 14CB H 563 0R2 RoHS 56 min 5 0.2
TLF 14CB H 683 0R2 RoHS 68 min 6.5 0.2
TLF9UA/TLF9UAH Type
TLF14CB/TLF14CBH Type
Test conditions
Equipment : HP-4192A Vosc-0.35V
Test circuit :
To impedance analyzer
■
Impedance-Frequency characteristic
1
coil0304_pack-P1
coil0304_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Minimum Quantity
Type Minimum Quantity (pcs.)
Box Bulk
CM05RA06 —500
CM05RB□□ 1000 —
CM08RA□□ — 250
CM08RB□□ 500 —
CM12RA02 —100
BU08RA□□ — 200
Type Minimum Quantity (pcs.)
Box
TLF9UA□500
TLF9UB□500
TLF14CB□500
◦CM/BU Type
◦TLF Type
146
1
trans01_e-01
■ FEATURES ■ APPLICATIONS
■ ELECTRICAL CHARACTERISTICS
■ OPERATING TEMP.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ High stability due to pair wire windings
◦ MC type : pins are molded into the base to create a singular structure
◦ This item can be custom designed to meet customer requirements
◦ Impedance transformers
◦ Distribution transformers
BALUN TRANSFORMERS
■ EXTERNAL DIMENSIONS/MINIMUM QUANTITY
Type Pin type
MB (BU05MB, BU06MB)
Surface-mount type
MC (BU05MC)
Fig.
■ ORDERING CODE
❶Type
BU Balun transformer
❻Internal code
△Standard product
△＝Blank space
❺Packaging
T Tape & Reel
△Bulk (Only pin type)
△＝Blank space
❸Shape
MB pin type
MC Surface-mount type
❷Length of component [mm]
05 5.0、5.3
06 6.0
B U 0 5 M B 0 1 △ ○
❶ ❷ ❸ ❹ ❺ ❻
❹Product classification code
example 01
A
B
CE
D
B
D
C A
Type A B C D E Minimum Quantity (pcs.)
Box Taping
BU05MB 5.5 max. 5.5 max. 6.0 max. 1.75±0.2 3.5 200 ー
（0.217 max.） （0.217 max.） （0.236 max.） （0.069±0.008） （0.138）
BU06MB 8 max. 8 max. 8 max. 2.25±0.2 pitch 3.5～5.0150 ー
（0.315 max.） （0.315 max.） （0.315 max.） （0.089±0.008）（0.138±0.197）
BU05MC 5.3±0.5 5.0±0.3 2.7±0.2 1.5±0.2 pitch ー ー 2500
（0.209±0.020）（0.197±0.012）（0.106±0.008）（0.059±0.008）
Unit : mm (inch)
Recommended Land Patterns
1.6
1.6
【BU05MC】
1
0.5
1
0.5
1
The following chart shows typical ranges for operating characteristics.
Please specify the following when ordering.
① loss
② standing wave ratio (VSWR)
③ operating frequency
④ specified test circuit
Unit : mm (inch)
REFLOWWAV E M C：M B：
◦ ー25℃～105℃（Including self-generated heat）
1
trans01_pack-P1
trans01_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
①Minimum Quantity
Type Minimum Quantity (pcs.)
Box Taping
BU05MC ー2500
BU05MB 200 ー
BU06MB 150 ー
②Tape material
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1 to 0.7N in the direction of the arrow
as illustrated below.
5.2±0.1
（0.209±0.004）
8
±
0.1
（0.315
±
0.004）
5.6
±
0.1
（0.220
±
0.004）
4±0.1
（0.157
±
0.004）
1.75±0.1
（0.069±0.004）
0.4±0.05
（0.016±0.002）
3.2
±
0.1
（0.126
±
0.004）
2±0.1
（0.079
±
0.004）
5.5±0.1
（0.217
±
0.004）
12
±
0.3
（0.472
±
0.012）
（ 1.5 ）
+0.1
-
0
（ 0.059 ）
+0.004
-
0
③Taping dimensions
◦Embossed tape 12mm wide (0.472 inches wide)
④Leader and Blank portion
Unit : mm (inch)
⑤Reel size
80±1
（3.15±0.039）
330±2
（12.99±0.079）
13.5±1
（0.53±0.039）
Label
Unit : mm (inch)
1
co0102tr01_reli-RP1 co0102tr01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating Temperature Range
CM01 ー40℃〜＋105℃
CM04RC ー25℃〜＋105℃
BU05MC
【Test Method and Remarks】
Including self-generated heat
3. Rated current
CM01
Within the specified tolerance.CM04RC
BU05MC
【Test Method and Remarks】
The maximum DC value having temperature increase within specified temperature,as detailed in individual specification.
4. Impedance
CM01
Within the specified tolerance.CM04RC
BU05MC
【Test Method and Remarks】
Measuring equipment : HP 4291A or its equivalent
Measuring frequency : Specified frequency
5. DC Resisitance
CM01
Within the specified tolerance.CM04RC
BU05MC
【Test Method and Remarks】
SMD transformer・Commom mode choke coil :
Measuring equipment : DC ohm meter
2. Storage Temperature Range
CM01
ー40℃〜＋85℃CM04RC
BU05MC
【Test Method and Remarks】
ー5 to ＋40℃ in taped packaging
7. Dielectric resistance : between wires
CM01
100MΩ min.CM04RC
BU05MC
【Test Method and Remarks】
Applied voltage : Rated voltage
Duration : 60 sec.
8. Rated voltage
CM01
Within the specification.CM04RC
BU05MC
6. Resistance to flexure of substrate
CM01 Within the specified tolerance.
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
According to JIS C 0051
CM01 CM04RC・BU05MC
Warp 2mm 3mm
Pressing speed 0.5mm/sec.
Duration 5±1sec.
9. Withstanding voltage : between wires
CM01
No abnormality.CM04RC
BU05MC
【Test Method and Remarks】
Applied voltage : Regulation voltage
Duration : 60 sec.
10. Resistance to vibration
CM01 No abnormality observed in appearance
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
According to JIS C 0040
Directions : 2 hrs each in X, Y, and Z directions. Total : 6 hrs
Frequency range : 10 to 55 to 10 Hz (1 min.)
Amplitude : 1.5mm (Shall not exceed acceleration 196m/s2)
Mounting method : soldering onto printed board
Recovery : At least 2 hrs of recovery under the standard condition after the test,followed by the measurement within 48 hrs.
1
co0102tr01_reli-RP2
co0102tr01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11. Solderability
CM01 At least 90% of terminal electrode is covered by new solder.
CM04RC At least 75% of terminal electrode is covered by new solder.
BU05MC
【Test Method and Remarks】
CM01 CM04RC・BU05MC
Solder temperature 245±5℃235±5℃
Duration 3±1sec. 2±0.5sec.
Immersion depth −Up to 0.5mm from terminal root
12. Resistance to solder Heat
CM01 Within the specified tolerance.
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
CM01 CM04RC・BU05MC
Reflow soldering
Preheating : 150 to 180℃ 1 to 2min
Peak : 255±5℃ 5sec.
230±5℃ 30〜40sec.
Number of reflow : Within 2 times
Preheating : 100 to 150℃ 1 to 2min
Peak : 230 to 240℃ within 5sec.
More than 200℃ within 40sec.
Number of reflow : Within 2 times
Manual soldering −
Solder temperature : 350±5℃
Duration : 3±1sec.
Recovery : 1 to 2hrs of recovery under the standard
condition after the test.
13. Thermal shock
CM01 Within the specified tolerance.
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
Accoding to JIS C 0025
Conditions of 1 cycle
Step Temperature (℃) Time (min)
CM01 CM04RC・BU05MC CM01 CM04RC・BU05MC
1ー40±3℃ ー25±3℃30±3
2 Room Temp. Room Temp. 3
3 85±2℃85±3℃30±3
4 Room Temp. Room Temp. 3
Number of cycle : CM01 : 100 cycle
CM04RC・BU05MC : 10 cycle
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1〜2 hour.
14. Loading under damp heat
CM01 Within the specified tolerance.
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
CM01 CM04RC・BU05MC
Temperature 60±2℃40±3℃
Humidity 90〜95％RH
Applied current Rated current
Duration 1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1〜2 hour.
15. High temperature life test
CM01 ー
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
CM04RC・BU05MC
Temperature 85±3℃
Duration 1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1〜2 hour.
16. Low Temperature life Test
CM01 Within the specified tolerance.
CM04RC Refer to individual specification.
BU05MC
【Test Method and Remarks】
CM01 CM04RC・BU05MC
Temperature −40±2℃ −40±3℃
Applied current 1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1〜2 hour.
1
co0102tr01_reli-RP3 co0102tr01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
17. Loading at high temperature life test
CM01 Within the specified tolerance.
CM04RC ー
BU05MC
【Test Method and Remarks】
CM01
Temperature 105±2℃
Applied current Rated current
Duration 1000±24hrs
Recovery : Recovery under the standard condition after removal from test chamber.
CM01 : Measuring it more than two hours and less than 48 hours.
CM04RC・BU05MC : Leave during 1〜2 hour.
Note on standard condition :
"standard condition" referred to herein is defined as follows:
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement results:
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition."
1
co0102tr01_reli-RP4 co0102tr01_reli_e-01
■ PRECAUTIONS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Land pattern design
1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of specifications.
Technical
consider-
ations
◆Land pattern design
Surface Mounting
・ Mounting and soldering conditions should be checked
beforehand.
・ Applicable soldering process to this products is reflow
soldering only.
・ Recommended Land Patterns
1.6
1.4
3.2
1.4
1.6
6.7
【CM04RC】 【BU05MC】
1.8 1.8 1
0.74
0.45
0.45
0.65 1.55
0.4 0.4
0.3
1.1
0.5
1
0.5
1
【CM01】
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Reflow soldering
1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified.
2. This product is reflow soldering only.
3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering.
◆Lead free soldering
1.
When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron
【CM04RC, BU05MC】
・ Put the soldering iron on the land-pattern.
・ Soldering iron's temperature - Below 350℃
・ Duration - 3 seconds or less
・ The soldering iron should not directly touch the inductor.
【CM01】
・ Please do not conduct an adjustment with a soldering iron because the wire would be broken due to its thinness.
Technical
consider-
ations
◆Reflow soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the
products.
5. Cleaning
Precautions ◆Cleaning conditions
1. Please contact any of our offices for a cleaning.
CM04RC, BU05MC, CM01
Unit
: mm
6. Handling
Precautions
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Breakaway PC boards (splitting along perforations)
1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the product any excessive mechanical shocks.
2. Please do not add any shock and power to a product in transportation.
◆Pick-up pressure
1. Please do not push to add any pressure to a winding part.
Please do not give any shock and push into a ferrite core exposure part.
◆Packing
1. Please avoid accumulation of a packing box as much as possible.
Technical
consider-
ations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards (splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. There is a case to be broken by the handling in transportation.
◆Pick-up pressure
1. Damage and a characteristic can vary with an excessive shock or stress.
◆Packing
1. There is a case that transformation and a product of tape are damaged by accumulation of a packing box.
7. Storage conditions
Precautions
◆Storage
1.
To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled.
・ Recommended conditions
Ambient temperature : 0〜40℃
Humidity : Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration
oftaping/packaging materials may take place.
1
co0304_reli-RP1 co0304_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating Temperature Range
CM-RA/BU-RA Type ー25〜＋105℃
CM-RB Type
TLF9U, TLF14CB TLF9U : ー25〜＋105℃, TLF14CB : ー25〜＋105℃
【Test method and remarks】
Including temperature rise due to self-generated heat.
2. Storage temperature range
CM-RA/BU-RA Type
ー40〜＋85℃CM-RB Type
TLF9U, TLF14CB
3. Rated current
CM-RA/BU-RA Type
Within the specified rangeCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM : The maximum DC value having temperature increase within specified temperature, as detailed in individual specification.
TLF9UA、14CB : The maximum AC value having temperature increase within 45℃ by the application of AC current.
TLF9UB : The maximum DC value having temperature increase within 45℃ by the application of DC current.
4. Inductance
CM-RA/BU-RA Type
Within the specified toleranceCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM :
Measuring equipment : 4263A (HP) or its equivalent
Measuring frequency : 1kHz
TLF9UA :
Measuring equipment : Impedance analyzer (HP4192A) or its equivalent
Measuring frequency : 1kHz
Measuring voltage : 0.35Vosc
TLF14CB :
Measuring equipment : LCR meter 4284A or its equivalent
Measuring frequency : 1kHz
Measuring voltage : 1.0V
5. DC resistance
CM-RA/BU-RA Type
Within the specified toleranceCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF : Measuring equipment : DC ohmmeter
6. Terminal strength tensile force
CM-RA/BU-RA Type
No abnormalityCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM : Fix the component in the direction to draw terminal and gradually apply tensile force as detailed in indiviual specifications.
TLF9U : Apply the stated tensile force gradually in the direction to draw terminal. TLF14CB : Apply the stated tensile force gradually in the direction to draw terminal.
Nominal wire diameter tensile
φd [mm] force [N] duration [s]
φ0.6 5 30±5
Nominal wire diameter tensile
φd [mm] force [N] duration [s]
φ0.8 10 30±5
7. Temperature rise
CM-RA/BU-RA Type Refer to individual specification
CM-RB Type
TLF9U, TLF14CB 45℃ max.
【Test method and remarks】
TLF : Resistance substitution method
Applied current : Rated current
Duration : 1 hour
8. Insulation resistance between wires
CM-RA/BU-RA Type
100MΩ min.CM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF : Applied voltage : Rated voltage (CM-RA/BU-RA, CM-RB）
: 500VDC (TLF9UA, 14CB)
: 250VDC (TLF9UB)
Duration : 60sec.
1
co0304_reli-RP2
co0304_reli_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
10. Withstanding : between wires
CM-RA/BU-RA Type
No abnormalityCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
CM・TLF : Applied voltage : 250VDC (CM-RA/BU-RA, CM-RB）
: 2000VAC (TLF9UA, 14CB）
: 500VDC (TLF9UB)
Duration : 60sec.
11. Withstanding : between wires and core
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB No abnormality
【Test method and remarks】
TLF : Applied voltage : 2000VAC (TLF9UA, 14CB)
: 500VDC (TLF9UB)
Duration : 60sec.
13. Resistance to vibration
CM-RA/BU-RA Type
CM-RB Type Appearance : No abnormality Inductance change : Within ±15%
TLF9U, TLF14CB TLF9U : Inductance change : Within ±5％ TLF14CB : Within the specified range
【Test method and remarks】
CM・TLF : According to JIS C 0040
Direction : 2hrs each in X, Y and Z direction Total : 6hrs
Frequency range : 10 to 55 to 10Hz (1 min.)
Amplitude : 1.5mm (shall not exceed acceleration 196m/s2)
Mounting method : soldering onto PC board
Recovery : 2 to 24 hrs of recovery under the standard condition after the test. (CM-RB)
: At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. (TLF9U, 14CB)
14. Solderability
CM-RA/BU-RA Type At least 75% of terminal electrode is covered by new solder.
CM-RB Type
TLF9U, TLF14CB Solder shall be uniformly adhered onto immersed surfaces.
【Test method and remarks】
CM : Solder temperature : 235±5℃
Duration : 2±0.5sec.
Immersion depth : According to detailed specification.
TLF : Solder temperature : 230±5℃
Duration : 2±0.5sec. (9U)
: 3±0.5sec. (14CB)
Immersion depth : Up to 1.0 to 1.5mm from PBC mounted level.
15. Resistance to soldering heat
CM-RA/BU-RA Type Appearance : No abnormality Inductance change : Refer to individual specification
CM-RB Type
TLF9U, TLF14CB TLF9UA : Inductance change : Within ±5% TLF14CB : Within the specified range
【Test method and remarks】
CM : Solder temperature : 260±5℃
Duration : 5±0.5sec.
Immersion depth : Up to 2〜2.5mm from terminal root.
Recovery : 1 to 2 hrs of recovery under the standard condition after the test.
TLF : Solder temperature : 260±5℃
Duration : 10±1sec. (9U, 14CB)
Immersion depth : Up to 1.0 to 1.5mm from PBC mounted level.
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
12. Rated voltage
CM-RA/BU-RA Type
Within the specified rangeCM-RB Type
TLF9U, TLF14CB
【Test method and remarks】
TLF9UA, 14CB : 250VAC
TLF9UB : 50VDC
■ RELIABILITY DATA
9. Insulation resistance between wire and core
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB 100MΩ min.
【Test method and remarks】
TLF : Applied voltage : 500VDC (TLF9UA, 14CB)
: 250VDC (TLF9UB)
Duration : 60 sec.
1
co0304_reli-RP3 co0304_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
17. Damp heat
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB TLF9UA : Inductance change : Within ±15%
TLF14CB : Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
TLF : Temperature : 60±2℃
40±2℃ (※TLF14CB)
Humidity : 90〜95％RH
Duration : 500 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
18. Loading under damp heat
CM-RA/BU-RA Type Appearance : No abnormality Inductance change : Refer to individual specification
CM-RB Type
TLF9U, TLF14CB Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
CM : Temperature : 40±2℃
Humidity : 90〜95%RH
Duration : 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from test chamber.
TLF : Temperature : 60±2℃
40±2℃ (※TLF14CB)
Humidity : 90〜95%RH
Duration : 100 hrs
500 hrs Apply rated current across windings (※TLF14CB)
Applied voltage : Apply the following specified voltage between windings.
TLF9UA 250VAC
TLF9UB 50VDC
Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
19. Loading at high temperature
CM-RA/BU-RA Type
CM-RB Type
TLF9U, TLF14CB Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
TLF : Temperature : 85±2℃
Duration : 100 hrs
500 hrs Apply rated current across windings (※TLF14CB)
Applied voltage : Apply the following specified voltage between windings.
TLF9UA 250VAC
TLF9UB 50VDC
Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
20. Low temperature life test
CM-RA/BU-RA Type Appearance : No abnormality Inductance change : Refer to individual specification
CM-RB Type
TLF9U, TLF14CB TLF9UA : Inductance change : Within ±15%
TLF14CB : Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
CM : Temperature : ー40±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RA)
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RB)
TLF : Temperature : ー25±2℃
: ー40±2℃ (※TLF14CB)
Duration : 500 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
16. Thermnal shock
CM-RA/BU-RA Type Appearance : No abnormality Inductance change : Refer to individual specification
CM-RB Type
TLF9U, TLF14CB TLF9UA : Inductance change : Within ±15%
TLF14CB : Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
CM, TLF :
According to JIS C 0025
Conditions for 1 cycle
Step Temperature 〔℃〕 Durration 〔min〕
1ー25±3 30±3
2 Room Temperature Within 3
3＋85±2 30±3
4 Room Temperature Within 3
Number of cycles : 10
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2 hrs.
1
co0304_reli-RP4
co0304_reli_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
21. High Temperature life test
CM-RA/BU-RA Type Appearance : No abnormality Inductance change : Refer to individual specification
CM-RB Type
TLF9U, TLF14CB TLF9U : Inductance change : Within ±15%
TLF14CB : Withstanding voltage : No abnormality Insulation resistance : No abnormality
【Test method and remarks】
CM : Temperature : 85±2℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RA)
: 1 to 2hrs of recovery under the standard condition after the removal from test chamber. (CM-RB)
TLF : Temperature : 85±2℃
: 105±3℃ (※TLF14CB)
Duration : 500 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs.
■ RELIABILITY DATA
1
co0304_reli-RP5 co0304_reli_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Design
1. Please design insertion pitches of a base in the pitches that fitted a terminal interval.
Technical
consider-
ations
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire Inductors in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, etc.
sufficiently.
◆Recommended conditions for using a soldering iron
・ Put the soldering iron on the land-pattern.
・ Soldering iron's temperature - Below 350℃
・ Duration - 3 seconds or less
・ The soldering iron should not directly touch the product.
Technical
consider-
ations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
4. Cleaning
Precautions
◆Cleaning conditions
1. TLF type
Please contact any of our offices for about a cleaning.
5. Handling
Precautions
◆Handling
1. Keep the product away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the product any excessive mechanical shocks.
2. TLF type
Please do not add any shock or and power to a product in transportation.
◆Packing
1. Please do not give the product any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
Technical
consider-
ations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. TLF type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead route turns at by a fall or an excessive shock.
6. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
・ Recommended conditions
Ambient temperature : 0〜40℃
Humidity : Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, product should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
CM-RA Type, CM-RB Type, TLF Type
■ PRECAUTIONS
