Product Specification 108-78434 17JUL09 Rev B MICRO USB CONNECTOR 1 Scope: 1. 1.1 Contents 1.1 1.1 This specification covers the requirements for MICRO USB CONNECTOR product performance, test methods and quality assurance provisions of MICRO USB CONNECTOR. Applicable product description and part numbers are as shown in Appendix 1. 2. 2. Applicable Documents: The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1 2.1 TE AMP A. 109-5000: B. 501-5914: A. TE AMP Specifications: A. 109-5000: Test Specification, General Requirements for Test Methods B. 501-5914: Qualification Test Report 2.2 2.2 Commercial Standards and Specifications A. ANSI/EIA 364-C A. ANSI/EIA 364-C B. USB cables and Connectors Class Document B. USB cables and Connectors Class Document Revision 2.0 Revision 2.0 3-5-8 Tel:044-844-8079 Fax:044-812-3203 (c)Copyright 2008 by Tyco Electronics AMP K.K. All Rights Reserved. 1 of 7 Product Specification 3. 108-78434 3. Requirements: 3.1 3.1 Design and Construction: Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2 3.2 A. A. Contact B. Housing (Plug & Receptacle) Material: Thermo Plastic C. Shell(Plug & Receptacle) Material: Stainless steel D. (Plug & Receptacle) Material: Copper alloy B. () C. Materials: D. Lock lever (plug) Material: Stainless steel 3.3 3.3 Ratings: A. 30V A. Voltage Rating: 30V MAX B. B. Current Rating . . 1, 5 pin 1.8A 2, 3 & 4 pin 0.5A 2, 3 & 4 pin 1A C. -3085 . 1, 5 pin 2, 3 & 4 pin . 2, 3 & 4 pin 3.4 :1535:45%75%(RH) :650mmHg800mmHg Rev. B 0.5A Max 1A Max C. Temperature Rating: -30 to 85 (Including D. -3085 1.8A Max temperature rising.) D. Storage Temperature: -30 to 85 3.4 Performance Requirements and Test Descriptions: Test specimens must be completely controlled products, and the printed circuit boards must be recommended. All tests are performed at following condition unless otherwise specified. Temperature:1535 Humidity :45%75% R.H. Pressure :650mmHg800mmHg 2 of 7 Product Specification 108-78434 3.5 3.5 Test Requirements and Procedures Summary Para. Test Items 3.5.1 Requirements Examination of Product Procedures 3.5.1 Meets requirements of product Visual inspection drawing. No physical damage Electrical Requirements 3.5.2 30m 20 mV 100 mA () R=10m 4 Fig.2 3.5.2 Contact Resistance Initial : 30m Max 20 mV Maximum open circuit at 100 mA (Low Level) Final : R=10m Max Maximum. 4-wire Kelvin 4-wire Kelvin All contacts measured All contacts measured Refer to Fig.2 3.5.3 1000M 100 M 500VDC 2 3.5.3 Insulation Resistance Initial : 1000M Min Apply 500V DC between adjacent contacts Final : 100 M Min for two minutes maximum, or until stabilized , mated. 3.5.4 3.5.4 withstanding Voltage No breakdown or flashover Fig.1 Rev. B 100VAC1 100VAC for one minute ,mated Fig.1 (CONT.) 3 of 7 Product Specification Para. Test Items 108-78434 Requirements Procedures Mechanical Requirements 3.5.5 35N 12.5mm/ 3.5.5 Mating Force 35N Max Measure force to mate at a rate of 12.5mm per minute maximum. 3.5.6 8N 12.5mm/ 3.5.6 Unmating Force 8N Min Measure force to mate at a rate of 12.5mm per minute maximum. 3.5.7 3.5.7 Durability 10,000 cycles 1500 cycles No physical damage and shall 10,000 cycles meet requirements of Cycle rate of 500 cycles per hour max. subsequent tests. 3.5.8 1.0 microsecond 315 5.35 GRMS EIA 364-28 Test Condition V Test letter A 3.5.8 Vibration No contact chatter greater 5.35 GRMS for 15 minutes in each of three than 1.0 microsecond. mutually perpendicular planes. EIA 364-28 Test Condition V Test letter A 3.5.9 40N 1 3.5.9 Cable pull out 40N Min Apply steady state axial load to the cable for one minute. 3.5.10 Pb: 2555 25555+0/-0.5 95 3.5.10 Solderability Solderable area shall have a 2555, for 5+0/-0.5 seconds. minimum of 95% solder coverage. For lead free solder pot temperature shall be +255 5 3.5.11 1.0s 30Gs6ms1/2 6 3(18) EIA 364-27 Test condition H 3.5.11 Shock No contact chatter greater 30Gs 6ms 1/2 sine than 1.0 microsecond. each 3shocks for 6 axes(Total 18shocks) EIA 364-27 Test condition H Fig. 1 Fig. 1 (CONT.) Rev. B 4 of 7 Product Specification Para. Test Items 108-78434 Requirements Procedures Environmental Requirements 3.5.12 +85 500 3.5.12 Temperature Life No physical damage and +85 for 500 hours mated. shall meet requirement of subsequent test. 3.5.13 -55+85 151 10 EIA 364-32 Test Condition I 3.5.13 3.5.14 3.5.14 3.5.15 Thermal Shock No physical damage and -55,+85, 15 minutes at each shall meet requirement of temperature , and 10 cycles , mated. subsequent test. EIA 364-32 Test Condition I 95% 2565 EIA 364-31 Test Condition A Method Humidity - Temperature No physical damage and 25 and 65 at 95% RH, seven cycles , Cycling shall meet requirements of mated. subsequent tests. EIA 364-31 Test Condition A Method EIA 364-65 ClassA 10 5() 5() (ClassA: RH% 702, Temp 301, Cl2 103ppb, NO2 20050ppb, H2S 105 ppb, SO2 10020ppb) 3.5.15 Mixed Flowing Gas No physical damage. EIA 364-65 ClassA for total 10 days. 5days(unmated) 5days(mated) (ClassA: RH% 702, Temp 301, Cl2 103ppb, NO2 20050ppb, H2S 105 ppb, SO2 10020ppb) Fig. 1 Fig. 1 (End.) Rev. B 5 of 7 Product Specification 108-78434 3.6 3.6 Product Qualification Test Sequence /Test Group Test Examination Test Ref. 1 2 3 4 5 /Test Sequence (a) 1,10 1,5 1,7 3,7 2,4 2,4,6 1,8 3.5.1 Examination of Product 3.5.2 Contact Resistance (Low Level) 3.5.3 Insulation Resistance 2,6 3.5.4 Dielectric withstanding Voltage 3,7 3.5.5 Mating Force 2 3.5.6 Unmating Force 8 3.5.7 Durability 4 3.5.8 Vibration 6(b) 3.5.9 Cable pull out 3.5.10 Solderability 3.5.11 Shock 3.5.12 Temperature Life 3.5.13 Thermal Shock 4 3.5.14 Damp Heat, Cyclic 5 3.5.15 Mixed Flowing Gas 1,3 9 2 5(b) 3 3,5 (a) / Numbers indicate sequence in which the tests are performed. (b) Discontinuities shall nit take place in this test examination, during tests. Product Part No. Description Remarks 1981584-1 Micro USB Receptacle type AB Standard mount 1981568-1 Micro USB Receptacle type B Standard mount 2013499-1 Micro USB Receptacle type B Dip 2 legs Trough hole mount 2069746-1 Micro USB Receptacle type B Dip short 2 legs Trough hole mount 2040002-1 Micro USB Receptacle type B Dip 4 legs Trough hole mount 2040343-2 Micro USB Receptacle type B Mid Mount 1939053-x Micro USB plug type A cable kit -- 1939054-x Micro USB plug type B cable kit -- 1 Appendix 1 Rev. B 6 of 7 Product Specification 108-78434 Fig.2 Measuring method of contact resistance Rev. B 7 of 7