FieldIT Data Sheet 10/15-4.01 EN Multi Vision(R) Four-wire add on unit for Pressure transmitter Serie 2000T 2-wire transmitter with integrated power supply Output signal 0...20 mA or 4...20 mA Power supply: 24 V or 230 V HART(R) communication at the transmitter is also possible Multi Vision(R) Four-wire add on unit for Pressure transmitter Serie 2000T The four-wire add-on unit for pressure transmitter 2000T provides a power supply device that is built right onto the transmitter. This unit is equipped with a separator between power supply and output signal. This construction enables using the two-wire transmitter as a four-wire transmitter with the option of either 24 V or 230 V power supplies. Output signal can be selected: 0...20 mA or 4...20 mA. HART communication direct to the transmitter is possible. The add-on unit is mounted to the transmitter at the factory. 10/15-4.01 EN Test voltage UC: 1.5 kV AC: 2.3 kV EMC tested according to DIN EN 61 326 Ambient conditions Operating temperature Storage temperature Condensation Housing Protection class Material Technical data Input 4...20 mA Dimensions H x W x D: Supply voltage min. 14V at 20 mA Weight approx. 0.7 kg Output 0(4)...20 mA (selectable) Colour RAL 7032, Smooth surface Characteristic increasing, linear Current limitation approx. 25 mA Maximum load 750 W Ripple max. 1 % v. input at max. load Power supply AC 230V (+6 % / -10 %): 47 ... 63 Hz; max. power consumption: 6 VA DC 24 V (18 ... 32 V): Allowable ripple is 2.5 Vpp within above-mentioned limits; max. power consumption: 3 W Deviation from characteristics max. 0.15 % v. input Time constant t90 max. 30 ms Influence due to Ambient temperature Load Power supply 0.1% / 10K 0.1% when changing from 0 % to 100 % 0.1% during a 10% change Galvanic separation between power supply and input power supply and output Insulation voltage according to DIN EN 61 010 AC 250 V Pollution degree 2 Overvoltage category II. 2 -20 C - +80 C -50 C - +85 C allowed (DIN40040) IP54 Cast aluminium, epoxy resin coat 125 x 80 x 60 mm Multi Vision(R) Four-wire add on unit for Pressure transmitter Serie 2000T 10/15-4.01 EN Dimensional drawings 3 ~30 A radius of 70 mm free space is required to swing open the local key unit cover ~125 2 1 b a 124 ~125 1 Transmitter 2 Electrical connection 3 Four-wire add-on unit Dimensions a" and b" are dependent on range and process connection: ~85 Process connection 1/2-14NPT male thread 1/2-14NPT female thread Ranges: 60 mbar 400 mbar a b 142 168 132 158 ~58 with a range of 600 bar Spigot DIN EN 837-1 G 1/2 B 141 Spigot DIN EN 837-1 G 1/2 B 152 (HP) for convex seal Front bonded diaphragm - For ball valve connection - Ranges: 2.5 bar a 147 143 b 173 169 167 178 146 147 157 172 173 183 - - 147 244 172 270 A radius of 70 mm free space is required to swing open the local key unit cover 85 125 1 30 3 35 108 125 58 2 173 3 Ordering information The following catalog numbers are appended to the catalog number of each respective transmitter. The transmitter 2010TD/ TA fitted with the four-wire add-on unit must use the DIN housing with electr. connection M 20x1.5 (amplifier housing ordering code M). The transmitter 2020TG/TA must use the barrel type housing with electr. connection M 20x1.5 (amplifier housing ordering code E). Ordering information for four-wire add-on unit Ordering number EUR LZ Amplifier housing accessories Power supply / output signal DC 24 V / 0...20 mA DC 24 V / 4...20 mA AC 230 V / 0...20 mA AC 230 V / 4...20 mA 5D1 5D3 5D2 5D4 Electrical connection of the add-on unit Threaded cable gland M 20x1.51) Plug Han 8U (only in conjunction with DC 24 V power supply) 1) Plug Han 7D (only in conjunction with DC 24 V power supply) 2) 1) see ordering no. of amplifier housing on the transmitter 2) 273 When plug connection on add-on unit required, please use code no. 273. It is also necessary to specify the plug connector on the transmitter. The IndustrialIT wordmark and all mentioned product names in the form XXXXXXIT are registered or pending trademarks of ABB. The Company's policy is one of continuous product improvement and the right is reserved to modify the information contained herein without notice. ABB has Sales & Customer Support expertise in over 100 countries worldwide. Printed in the Fed. Rep. of Germany (01.03) (c) ABB 2003 ABB Ltd. Howard Road, St. Neots Cambridgeshire, PE19 8EU UK Phone: +44(0)1480 475321 Fax: +44(0)1480 217948 10/15-4.01 EN Rev A www.abb.com ABB Inc. 125 E. County Line Road Warminster, PA 18974 USA Phone: +1 215 674 6000 Fax: +1 215 674 7183 ABB Automation Products GmbH Schillerstrae 72 32425 Minden GERMANY Phone: +49 571 830-0 Fax: +49 571 830-1470