General Description
The MAX691A/MAX693A/MAX800L/MAX800M micro-
processor (µP) supervisory circuits are pin-compatible
upgrades to the MAX691, MAX693, and MAX695. They
improve performance with 30µA supply current, 200ms
typ reset active delay on power-up, and 6ns chip-
enable propagation delay. Features include write pro-
tection of CMOS RAM or EEPROM, separate watchdog
outputs, backup-battery switchover, and a RESET out-
put that is valid with VCC down to 1V. The MAX691A/
MAX800L have a 4.65V typical reset-threshold voltage,
and the MAX693A/MAX800Ms’ reset threshold is 4.4V
typical. The MAX800L/MAX800M guarantee power-fail
accuracies to ±2%.
________________________Applications
Computers
Controllers
Intelligent Instruments
Automotive Systems
Critical µP Power Monitoring
____________________________Features
200ms Power-OK/Reset Timeout Period
A Standby Current, 30µA Operating Current
On-Board Gating of Chip-Enable Signals,
10ns max Delay
MaxCapor SuperCapCompatible
Guaranteed RREESSEETTAssertion to VCC = +1V
Voltage Monitor for Power-Fail or Low-Battery
Warning
Power-Fail Accuracy Guaranteed to ±2%
(MAX800L/M)
Available in 16-Pin Narrow SO, Plastic
DIP, and TSSOP Packages
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
________________________________________________________________ Maxim Integrated Products 1
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
RESET
RESET
WDO
CE IN
GND
VCC
VOUT
VBATT
TOP VIEW
MAX691A
MAX693A
MAX800L
MAX800M
CE OUT
WDI
PFO
PFI
OSC SEL
OSC IN
LOW LINE
BATT ON
DIP/SO/TSSOP
Pin Configuration
MAX691A
MAX693A
MAX800L
MAX800M
VOUT
VCC BATT ON
CE OUT
CE IN
WDI
PFO
RESET
VBATT
PFI
GND
OSC IN
OSC SEL
1
9
4
7
8
ADDRESS
DECODE
AUDIBLE
ALARM
5V
REGULATOR
+8V
0.1µF
CMOS RAM
2
12
11
10
15
13
5
3
A0-A15
I/O
NMI
RESET
µP
LOW LINE WDO
SYSTEM STATUS INDICATORS
NO
CONNECTION
0.47F*
1N4148
*MaxCap
614
Typical Operating Circuit
19-0094; Rev 10; 11/05
PART
MAX691ACUE
MAX691ACPE 0°C to +70°C
0°C to +70°C
TEMP RANGE PIN-PACKAGE
16 TSSOP
16 Plastic DIP
MAX691AC/D
MAX691AEJE -40°C to +85°C
0°C to +70°C Dice*
16 CERDIP
MAX691AEUE
MAX691AESE -40°C to +85°C
0°C to +70°C 16 TSSOP
16 Narrow SO
MAX691AEPE -40°C to +85°C 16 Plastic DIP
MAX691AMJE -55°C to +125°C 16 CERDIP
SuperCap is a registered trademark of Baknor Industries. MaxCap is a registered trademark of The Carborundum Corp.
MAX691ACSE 0°C to +70°C 16 Narrow SO
Ordering Information continued on last page.
*Dice are specified at TA= +2C, DC parameters only.
Devices in PDIP, SO and TSSOP packages are available in both
leaded and lead-free packaging. Specify lead free by adding
the + symbol at the end of the part number when ordering.
Lead free not available for CERDIP package.
MAX691ACWE 0°C to +70°C 16 Wide SO
MAX691AEWE -40°C to +85°C 16 Wide SO
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Ordering Information
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
2_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(MAX691A, MAX800L: VCC = +4.75V to +5.5V; MAX693A, MAX800M: VCC = +4.5V to +5.5V; VBATT = 2.8V, TA= TMIN to TMAX,
unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Terminal Voltage (with respect to GND)
VCC .......................................................................-0.3V to +6V
VBATT...................................................................-0.3V to +6V
All Other Inputs .....................................-0.3V to (VOUT + 0.3V)
Input Current
VCC Peak...........................................................................1.0A
VCC Continuous.............................................................250mA
VBATT Peak ..................................................................250mA
VBATT Continuous ..........................................................25mA
GND, BATT ON .............................................................100mA
All Other Outputs ............................................................25mA
Continuous Power Dissipation (TA= +70°C)
TSSOP (derate 6.70mW/°C above +70°C) ..................533mW
Narrow SO (derate 8.70mW/°C above +70°C) ...........696mW
Wide SO (derate 9.52mW/°C above +70°C)...............762mW
Plastic DIP (derate 10.53mW/°C above +70°C) ..........842mW
CERDIP (derate 10.00mW/°C above +70°C)..............800mW
Operating Temperature Ranges
MAX69_AC_ _/MAX800_C_ _ .............................0°C to +70°C
MAX69_AE_ _/MAX800_E_ _ ...........................-40°C to +85°C
MAX69_AMJE ................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10s) .................................+300°C
VBATT - 0.15
MAX69_AC, MAX800_C 0.8 1.2
VBATT = 4.5V, IOUT = 20mA
µA
-1.0 0.02
VBATT + 0.2V VCC
VBATT Standby Current
(Note 3)
-0.1 0.02
µA
5
VCC < VBATT - 1.2V,
VBATT = 2.8V
Supply Current in
Battery-Backup Mode
(excludes IOUT) (Note 2)
VBATT = 2.8V, IOUT = 10mA
V0 5.5
CONDITIONS
Operating Voltage Range,
VCC, VBATT (Note 1)
VBATT = 4.5V
0.04 1
µA30 100
Supply Current in
Normal Operating Mode
(excludes IOUT)
V
VOUT in Battery-Backup
Mode VBATT - 0.25
VBATT = 2.8V
30
VBATT - 0.3
VBATT-to-VOUT
On-Resistance
UNITSMIN TYP MAXPARAMETER
25
TA= +25°C
VCC > VBATT - 1V
TA= TMIN + TMIN
VBATT = 2.0V, IOUT = 5mA
TA= +25°C
TA= TMIN + TMIN
15
VBATT = 2.0V
VCC = 4.5V IOUT = 250mA
VCC - 0.02 VCC - 0.05IOUT = 25mA
MAX69_AC/AE,
MAX800_C/E
IOUT = 210mA
VCC - 0.2 VCC - 0.35
VCC - 0.2 VCC - 0.3
V
VCC - 0.40
VCC - 0.17 VCC - 0.3V
VOUT Output
MAX69_AE,
MAX800_C/E
MAX69_AC
MAX69_A/M
MAX69_AE, MAX800_E 0.8 1.4
MAX69_A/M 0.8 1.6
VCC = 4.5VVCC-to-VOUT On-Resistance
V
VBATT - 0.3
Power-up
Battery Switchover
Threshold
VBATT + 0.3
Power-down
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
_______________________________________________________________________________________ 3
MAX691A, MAX800L
mA720
RESET Output Short-Circuit
Current
V
3.5
RESET Output Voltage 0.1 0.4
0.004 0.3
ns100
Minimum Watchdog Input
Pulse Width
Clock
Cycles
1024
Watchdog Timeout Period,
External Clock (Note 4)
4096
ms70 100 140
Watchdog Timeout Period,
Internal Oscillator
1.0 1.6 2.25
Clock
Cycles
2048
Reset Active Timeout Period,
External Clock (Note 4)
ms140 200 280
Reset Active Timeout Period,
Internal Oscillator
ns800
LOW LINE-to-RESET Delay
µs80VCC to RESET Delay
MAX693A, MAX800M
CONDITIONS
mV15Reset Threshold Hysteresis
V
4.30 4.45
Reset Threshold Voltage 4.55 4.70
4.25 4.40 4.50
4.50 4.65 4.75
UNITSMIN TYP MAXPARAMETER
Output source current
ISOURCE = 1.6mA, VCC = 5V
ISINK = 3.2mA, VCC = 4.25V
ISINK = 50µA, VCC = 1V, VBATT = 0V, VCC falling
VIL = 0.8V, VIH = 0.75 x VCC
Short period
Long period
Short period
Long period
MAX800M, TA= +25°C, VCC falling
Power-up
Power-up
MAX800L, TA= +25°C, VCC falling
Power-down
ELECTRICAL CHARACTERISTICS (continued)
(MAX691A, MAX800L: VCC = +4.75V to +5.5V; MAX693A, MAX800M: VCC = +4.5V to +5.5V; VBATT = 2.8V, TA= TMIN to TMAX,
unless otherwise noted.)
RESET Output Voltage Low
(Note 5) ISINK = 3.2mA 0.1 0.4 V
ISINK = 3.2mA, VCC = 4.25V 0.4
LOW LINE Output Voltage ISOURCE = 1µA, VCC = 5V 3.5 V
LOW LINE Output
Short-Circuit Current Output source current 115100 µA
ISINK = 3.2mA 0.4
WDO Output Voltage ISOURCE = 500µA, VCC = 5V 3.5 V
WDO Output
Short-Circuit Current Output source current 310mA
VIH 0.75 x VCC
WDI Threshold Voltage
(Note 6) VIL 0.8 V
WDI = 0V -50 -10
WDI Input Current WDI = VOUT 20 50 µA
sec
mV60
Battery Switchover
Hysteresis
ISINK = 25mA V
0.7 1.5
BATT ON Output
Low Voltage
ISINK = 3.2mA 0.1 0.4
Source current µA115100
BATT ON Output
Short-Circuit Current
Sink current mA60
RESET AND WATCHDOG TIMER
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
4_______________________________________________________________________________________
MAX69_AC/AE/AM, VCC = 5V
µA0.10 ±5OSC IN Leakage Current
µs12
RESET-to-CE OUT Delay
2.7
CE OUT Output Voltage High
(Reset Active)
3.5
ns610
CE IN-to-CE OUT Propagation
Delay (Note 8)
mA0.1 0.75 2.0
CE OUT Short-Circuit Current
(Reset Active)
75 150
CE IN-to-CE OUT Resistance
(Note 7)
µA±0.005 ±1
CE IN Leakage Current
60
PFI-to-PFO Delay µs
25
µA115100
PFO Output Short-Circuit
Current
MAX800_C/E, VCC = 5V
CONDITIONS
3.5
PFO Output Voltage V
0.4
nA±0.01 ±25PFI Leakage Current
1.225 1.25 1.275
PFI Input Threshold V
1.2 1.25 1.3
UNITSMIN TYP MAXPARAMETER
OSC SEL = 0V
Power-down
VCC = 0V, VBATT = 2.8V, IOUT = 1µA
VCC = 5V, IOUT = -100µA
50source impedance driver, CLOAD = 50pF
Disable mode,
CE OUT = 0V
Enable mode
Disable mode
ISOURCE = 1µA, VCC = 5V
ISINK = 3.2mA
VIN = 20mV, VOD = 15mV
VIN = -20mV, VOD = 15mV
Output source current
Note 1: Either VCC or VBATT can go to 0V, if the other is greater than 2.0V.
Note 2: The supply current drawn by the MAX691A/MAX800L/MAX800M from the battery excluding IOUT typically goes to 10µA
when (VBATT - 1V) < VCC < VBATT. In most applications, this is a brief period as VCC falls through this region.
Note 3: “+” = battery-discharging current, “--” = battery-charging current.
Note 4: Although presented as typical values, the number of clock cycles for the reset and watchdog timeout periods are fixed and
do not vary with process or temperature.
Note 5: RESET is an open-drain output and sinks current only.
Note 6: WDI is internally connected to a voltage divider between VOUT and GND. If unconnected, WDI is driven to 1.6V (typ),
disabling the watchdog function.
Note 7: The chip-enable resistance is tested with VCC = +4.75V for the MAX691A/MAX800L and VCC = +4.5V for the
MAX693A/MAX800M. CE IN = CE OUT = VCC / 2.
Note 8: The chip-enable propagation delay is measured from the 50% point at CE IN to the 50% point at CE OUT.
ELECTRICAL CHARACTERISTICS (continued)
(MAX691A, MAX800L: VCC = +4.75V to +5.5V; MAX693A, MAX800M: VCC = +4.5V to +5.5V; VBATT = 2.8V, TA= TMIN to TMAX,
unless otherwise noted.)
kHz50OSC IN Frequency Range
µA10 100OSC SEL Input Pull-Up Current
µA10 100OSC IN Input Pull-Up Current
OSC SEL = 0V
OSC SEL = 0V
OSC SEL = VOUT or floating, OSC IN = 0V
V
VOUT - 0.3 VOUT - 0.6VIH
3.65 2.00
OSC IN External Oscillator
Threshold Voltage VIL
kHz100
OSC IN Frequency with
External Capacitor OSC SEL = 0V, COSC = 47pF
V
POWER-FAIL COMPARATOR
CHIP-ENABLE GATING
INTERNAL OSCILLATOR
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
_______________________________________________________________________________________ 5
36
26
-60 120 150
VCC SUPPLY CURRENT
vs. TEMPERATURE
(NORMAL OPERATING MODE)
34
MAX691A TOC-01
TEMPERATURE (°C)
VCC SUPPLY CURRENT (µA)
30
30
28
-30 0 90
32
60
VCC = 5V
VBATT = 2.8V
PFI, CE IN = 0V
0
-60 120 150
BATTERY SUPPLY CURRENT
vs. TEMPERATURE
(BATTERY-BACKUP MODE)
2
MAX691A TOC-02
TEMPERATURE (°C)
BATTERY SUPPLY CURRENT (µA)
30
1
0.5
-30 0 90
1.5
60
VCC = 5V
VBATT = 2.8V
NO LOAD
120
-60 120 150 180
CHIP-ENABLE ON-RESISTANCE
vs. TEMPERATURE
100
MAX691A TOC-03
TEMPERATURE (°C)
CE ON-RESISTANCE ()
30
60
40
-30 0 90
80
60
VCC = 4.75V
VBATT = 2.8V
VCE IN = VCC/2
20
5
-60 120 150
VBATT to VOUT ON-RESISTANCE
vs. TEMPERATURE
MAX691A TOC-04
TEMPERATURE (°C)
VBATT-to-VOUT ON-RESISTANCE ()
30
10
-30 0 90
15
60
VCC = 0V
VBATT = 2.8V
VBATT = 2.0V
VBATT = 4.5V
4.75
4.30
-60 120 150
RESET THRESHOLD
vs. TEMPERATURE
MAX691A TOC-07
TEMPERATURE (°C)
RESET THRESHOLD (V)
30
4.45
-30 0 90
4.65
4.40
4.35
4.50
4.70
4.55
4.60
60
VBATT = 2.8V
MAX691A
MAX800L
MAX693A
MAX800M
1.2
0.6
-60 120 150
VCC to VOUT ON-RESISTANCE
vs. TEMPERATURE
MAX691A TOC-05
TEMPERATURE (°C)
VCC-to-VOUT ON-RESISTANCE ()
30
0.8
-30 0 90
1.0
0.7
0.9
1.1
60
VCC = 5V,
VBATT = 0V
1.50
0
-60 120 150
PFI THRESHOLD
vs. TEMPERATURE
MAX691A TOC-06
TEMPERATURE (°C)
PFI THRESHOLD (V)
30
0.50
-30 0 90
1.00
0.25
0.75
1.25
60
VCC = +5V,
VBATT = 0V
NO LOAD ON PFO
600
0
-60 120 150
RESET OUTPUT RESISTANCE
vs. TEMPERATURE
MAX691A TOC-08
TEMPERATURE (°C)
RESET OUTPUT RESISTANCE ()
30
200
-30 0 90
100
500
300
400
60
VCC = 5V, VBATT = 2.8V
SOURCING CURRENT
VCC = 0V, VBATT = 2.8V
SINKING CURRENT
-60 120 150
RESET DELAY
vs. TEMPERATURE
230
MAX691A TOC-09
TEMPERATURE (°C)
RESET DELAY (ms)
30
190
170
-30 0 90
210
220
180
200
60
VCC = 0V TO 5V STEP
VBATT = 2.8V
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
6_______________________________________________________________________________________
____________________________Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
20
0
0
BATTERY CURRENT
vs. INPUT SUPPLY VOLTAGE
16
MAX691A TOC-10
VCC (V)
IBATT (µA)
3
8
4
12 5
12
4
VBATT = 2.8V
IOUT = 0A
100
0.1
WATCHDOG AND RESET TIMEOUT PERIOD
vs. OSC IN TIMING CAPACITOR (COSC)
10
MAX691A TOC-11
COSC (pF)
WATCHDOG AND RESET TIMEOUT PERIOD (sec)
100
1
10 1000
VCC = 5V
VBATT = 2.8V LONG WATCHDOG
TIMEOUT PERIOD
SHORT WATCHDOG
TIMEOUT PERIOD
RESET ACTIVE
TIMEOUT PERIOD
0300
CHIP-ENABLE PROPAGATION DELAY
vs. CE OUT LOAD CAPACITANCE
MAX691A TOC-12
CLOAD (pF)
PROPAGATION DELAY (ns)
150
8
0
50 100 250
16
20
4
12
200
VCC = 5V
CE IN = 0V TO 5V
DRIVER SOURCE
IMPEDANCE = 50
1000
1
1
VCC to VOUT vs. OUTPUT CURRENT
(NORMAL OPERATING MODE)
100
MAX691A TOC-13
IOUT (mA)
VCC to VOUT (mV)
100
10
10 1000
VCC = 4.5V
VBATT = 0V
SLOPE = 0.8
1000
1
VBATT to VOUT vs. OUTPUT CURRENT
(BATTERY-BACKUP MODE)
100
MAX691A TOC-14
IOUT (mA)
VBATT to VOUT (mV)
10
10
1100
VCC = 0V
VBATT = 4.5V
SLOPE = 8
LO
VCC to LOW LINE
AND CE OUT DELAY
MAX691A TOC-15
LOW LINE
5V
VCC RESET
THRESHOLD
LO
HI
HI
HI
LO
CE OUT
RESET
12µs
800ns
80µs
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
_______________________________________________________________________________________ 7
______________________________________________________________Pin Description
NAME FUNCTION
1VBATT Battery-Backup Input. Connect to external battery or capacitor and charging circuit. If backup battery is not
used, connect to GND.
2 VOUT
Output Supply Voltage. When VCC is greater than VBATT and above the reset threshold, VOUT connects to
VCC. When VCC falls below VBATT and is below the reset threshold, VOUT connects to VBATT. Connect a 0.1µF
capacitor from VOUT to GND. Connect VOUT to VCC if no backup battery is used.
PIN
3 VCC Input Supply Voltage, 5V input.
4GND Ground. 0V reference for all signals.
8OSC SEL
Oscillator Select. When OSC SEL is unconnected or driven high, the internal oscillator sets the reset delay and
watchdog timeout period. When OSC SEL is low, the external oscillator input (OSC IN) is enabled (Table 1).
OSC SEL has a 10µA internal pull-up.
7OSC IN
External Oscillator Input. When OSC SEL is unconnected or driven high, a 10µA pull-up connects from VOUT to
OSC IN, the internal oscillator sets the reset and watchdog timeout periods, and OSC IN selects between fast
and slow watchdog timeout periods. When OSC SEL is driven low, the reset and watchdog timeout periods may
be set either by a capacitor from OSC IN to ground or by an external clock at OSC IN (Figure 3).
6LOW LINE LOW LINE output goes low when VCC falls below the reset threshold. It returns high as soon as VCC rises above
the reset threshold.
5BATT ON
Battery On Output. When VOUT switches to VBATT, BATT ON goes high. When VOUT switches to VCC, BATT ON
goes low. Connect the base of a PNP through a current-limiting resistor to BATT ON for VOUT current require-
ments greater than 250mA.
13 CE IN Chip-Enable Input. The input to chip-enable gating circuit. If CE IN is not used, connect CE IN to GND or VOUT.
12 CE OUT Chip-Enable Output. CE OUT goes low only when CE IN is low and VCC is above the reset threshold. If CE IN is
low when reset is asserted, CE OUT will stay low for 15µs or until CE IN goes high, whichever occurs first.
11 WDI
Watchdog Input. WDI is a three-level input. If WDI remains either high or low for longer than the watchdog time-
out period, WDO goes low and reset is asserted for the reset timeout period. WDO remains low until the next tran-
sition at WDI. Leaving WDI unconnected disables the watchdog function. WDI connects to an internal voltage
divider between VOUT and GND, which sets it to mid-supply when left unconnected.
10 PFO Power-Fail Output. This is the output of the power-fail comparator. PFO goes low when PFI is less than 1.25V.
This is an uncommitted comparator, and has no effect on any other internal circuitry.
9PFI Power-Fail Input. This is the noninverting input to the power-fail comparator. When PFI is less than 1.25V, PFO
goes low. When PFI is not used, connect PFI to GND or VOUT .
16 RESET RESET is an active-high output. It is open drain, and the inverse of RESET.
15 RESET RESET Output goes low whenever VCC falls below the reset threshold. RESET will remain low typically for
200ms after VCC crosses the reset threshold on power-up.
14 WDO Watchdog Output. If WDI remains high or low longer than the watchdog timeout period, WDO goes low and reset
is asserted for the reset timeout period. WDO returns high on the next transition at WDI. WDO remains high if
WDI is unconnected.
_______________Detailed Description
R
E
S
E
T
and RESET Outputs
The MAX691A/MAX693A/MAX800L/MAX800M’s RESET
and RESET outputs ensure that the µP (with reset
inputs asserted either high or low) powers up in a
known state, and prevents code-execution errors dur-
ing power-down or brownout conditions.
The RESET output is active low, and typically sinks
3.2mA at 0.1V saturation voltage in its active state.
When deasserted,
RESET sources 1.6mA at typically
VOUT - 0.5V. RESET output is open drain, active high,
and typically sinks 3.2mA with a saturation voltage of
0.1V. When no backup battery is used, RESET output is
guaranteed to be valid down to VCC = 1V, and an
external 10kpull-down resistor on RESET insures
that it will be valid with VCC down to GND (Figure 1).
As VCC goes below 1V, the gate drive to the RESET
output switch reduces accordingly, increasing the
RDS(ON) and the saturation voltage. The 10kpull-
down resistor insures the parallel combination of switch
plus resistor is around 10kand the output saturation
voltage is below 0.4V while sinking 40µA. When using
a 10kexternal pull-down resistor, the high state for
RESET output with VCC = 4.75V will be 4.5V typical.
For battery voltages 2V connected to VBATT, RESET
and RESET remain valid for VCC from 0V to 5.5V.
MAX691A/MAX693A/MAX800L/MAX800M
RESET and RESET are asserted when VCC falls below
the reset threshold (4.65V for the MAX691A/MAX800L,
4.4V for the MAX693A/MAX800M) and remain asserted
for 200ms typ after VCC rises above the reset threshold
on power-up (Figure 5). The devices’ battery-
switchover comparator does not affect reset assertion.
However, both reset outputs are asserted in battery-
backup mode since VCC must be below the reset
threshold to enter this mode.
Watchdog Function
The watchdog monitors µP activity via the Watchdog
Input (WDI). If the µP becomes inactive, RESET and
RESET are asserted. To use the watchdog function,
connect WDI to a bus line or µP I/O line. If WDI
remains high or low for longer than the watchdog time-
out period (1.6sec nominal), WDO, RESET, and RESET
are asserted (see RESET and
RESET
Outputs section,
and the Watchdog Output discussion on this page).
Watchdog Input
A change of state (high to low, low to high, or a mini-
mum 100ns pulse) at the WDI during the watchdog
period resets the watchdog timer. The watchdog
default timeout is 1.6sec.
To disable the watchdog function, leave WDI floating.
An internal resistor network (100kequivalent imped-
ance at WDI) biases WDI to approximately 1.6V.
Internal comparators detect this level and disable the
watchdog timer. When VCC is below the reset thresh-
old, the watchdog function is disabled and WDI is dis-
connected from its internal resistor network, thus
becoming high impedance.
Watchdog Output
The Watchdog Output (WDO) remains high if there is a
transition or pulse at WDI during the watchdog timeout
period. The watchdog function is disabled and
WDO is
a logic high when VCC is below the reset threshold, bat-
tery-backup mode is enabled, or WDI is an open circuit.
In watchdog mode, if no transition occurs at WDI during
the watchdog timeout period, RESET and RESET are
asserted for the reset timeout period (200ms typical).
WDO goes low and remains low until the next transition
at WDI (Figure 2). If WDI is held high or low indefinitely,
RESET and RESET will generate 200ms pulses every
1.6sec. WDO has a 2 x TTL output characteristic.
Selecting an Alternative
Watchdog and Reset Timeout Period
The OSC SEL and OSC IN inputs control the watchdog
and reset timeout periods. Floating OSC SEL and OSC
IN or tying them both to VOUT selects the nominal 1.6sec
watchdog timeout period and 200ms reset timeout peri-
od. Connecting OSC IN to GND and floating or connect-
ing OSC SEL to VOUT selects the 100ms normal
watchdog timeout delay and 1.6sec delay immediately
after reset. The reset timeout delay remains 200ms
(Figure 2). Select alternative timeout periods by con-
necting OSC SEL to GND and connecting a capacitor
between OSC IN and GND, or by externally driving OSC
IN (Table 1 and Figure 3). OSC IN is internally connect-
ed to a ±100nA (typ) current source that charges and
discharges the timing capacitor to create the oscillator
frequency, which sets the reset and watchdog timeout
periods (see Connecting a Timing Capacitor at OSC IN
in the Applications Information section).
Microprocessor Supervisory Circuits
8_______________________________________________________________________________________
WDI
WDO
RESET t1t1t3
t2
t1 = RESET TIMEOUT PERIOD
t2 = NORMAL WATCHDOG TIMEOUT PERIOD
t3 = WATCHDOG TIMEOUT PERIOD IMMEDIATELY AFTER RESET
Figure 1. Adding an external pull-down resistor ensures
R
E
S
E
T
is valid with VCC down to GND.
Figure 2. Watchdog Timeout Period and Reset Active Time
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
_______________________________________________________________________________________ 9
Chip-Enable Signal Gating
The MAX691A/MAX693A/MAX800L/MAX800M provide
internal gating of chip-enable (CE) signals to prevent
erroneous data from being written to CMOS RAM in the
event of a power failure. During normal operation, the
CE gate is enabled and passes all CE transitions. When
reset is asserted, this path becomes disabled, prevent-
ing erroneous data from corrupting the CMOS RAM. All
these parts use a series transmission gate from
CE IN to
CE OUT (Figure 4).
The 10ns max CE propagation delay from CE IN to CE
OUT enables the parts to be used with most µPs.
Chip-Enable Input
The Chip-Enable Input (CE IN) is high impedance (dis-
abled mode) while RESET and RESET are asserted.
During a power-down sequence where VCC falls below
the reset threshold or a watchdog fault,
CE IN assumes
a high-impedance state when the voltage at CE IN
goes high or 15µs after reset is asserted, whichever
occurs first (Figure 5).
During a power-up sequence, CE IN remains high
impedance, regardless of CE IN activity, until reset is
deasserted following the reset timeout period.
In the high-impedance mode, the leakage currents into
this terminal are ±1µA max over temperature. In the
low-impedance mode, the impedance of
CE IN appears
as a 75resistor in series with the load at CE OUT.
The propagation delay through the CE transmission
gate depends on both the source impedance of the
drive to
CE IN and the capacitive loading on the Chip-
Enable Output (
CE OUT) (see Chip-Enable Propagation
Delay vs. CE OUT Load Capacitance in the Typical
Operating Characteristics). The CE propagation delay
is production tested from the 50% point of
CE IN to the
50% point of
CE OUT using a 50driver and 50pF of
load capacitance (Figure 6). For minimum propagation
delay, minimize the capacitive load at CE OUT, and
use a low output-impedance driver.
Chip-Enable Output
In the enabled mode, the impedance of CE OUT is
equivalent to 75in series with the source driving CE
IN. In the disabled mode, the 75transmission gate is
off and CE OUT is actively pulled to VOUT. This source
turns off when the transmission gate is enabled.
L
O
W
L
I
N
E
Output
LOW LINE is the buffered output of the reset threshold
comparator. LOW LINE typically sinks 3.2mA at 0.1V.
For normal operation (VCC above the LOW LINE thresh-
old), LOW LINE is pulled to VOUT.
Power-Fail Comparator
The power-fail comparator is an uncommitted comparator
that has no effect on the other functions of the IC.
Common uses include low-battery indication (Figure 7),
and early power-fail warning (see Typical Operating
Circuit).
Power-Fail Input
Power Fail Input (PFI) is the input to the power-fail com-
parator. It has a guaranteed input leakage of ±25nA
max over temperature. The typical comparator delay is
25µs from VIL to VOL (power failing), and 60µs from VIH
to VOH (power being restored). If PFI is not used, con-
nect it to ground.
Figure 3. Oscillator Circuits
Watchdog Timeout Period
OSC SEL OSC IN Normal Immediately After Reset Reset Timeout Period
Low External Clock Input 1024 clks 4096 clks 2048 clks
Low External Capacitor (600/47pF x C)ms (2.4/47pF x C)sec (1200/47pF x C)ms
Floating Low 100ms 1.6sec 200ms
Floating Floating 1.6sec 1.6sec 200ms
Table 1. Reset Pulse Width and Watchdog Timeout Selections
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
10 ______________________________________________________________________________________
MAX691A
MAX693A
MAX800L
MAX800M
CHIP-ENABLE
OUTPUT
CONTROL
VCC 3
1
13
7
11
9
VBATT
CE IN
OSC IN
WDI
PFI
RESET
GENERATOR
TIMEBASE FOR
RESET AND
WATCHDOG
WATCHDOG
TRANSITION
DETECTOR
WATCHDOG
TIMER
8
OSC SEL
1.25V
GND
4
4.65V* 6LOW LINE
5
2
12
15
16
14
PFO
WDO
RESET
RESET
CE OUT
10
VOUT
BATT ON
* 4.4V FOR THE MAX693A/MAX800M
VCC
CE IN
RESET
THRESHOLD
CE OUT
RESET
RESET
100µs
15µs
100µs
5.0V
4.0V
5.0V
0V
5V
0V
5V
0V
0V
5V
LOGIC LEVELS SHOWN ARE FROM 0V TO 5V.
Figure 4. MAX691A/MAX693A/MAX800L/MAX800M Block Diagram
Figure 5. Reset and Chip-Enable Timing
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
______________________________________________________________________________________ 11
Power-Fail Output
The Power-Fail Output (PFO) goes low when PFI goes
below 1.25V. It typically sinks 3.2mA with a saturation
voltage of 0.1V. With PFI above 1.25V, PFO is actively
pulled to VOUT.
Battery-Backup Mode
Two conditions are required to switch to battery-back-
up mode: 1) VCC must be below the reset threshold,
and 2) VCC must be below VBATT. Table 2 lists the sta-
tus of the inputs and outputs in battery-backup mode.
Battery On Output
The Battery On (BATT ON) output indicates the status
of the internal VCC/battery-switchover comparator,
which controls the internal VCC and VBATT switches.
For VCC greater than VBATT (ignoring the small hys-
teresis effect), BATT ON typically sinks 3.2mA at 0.1V
saturation voltage. In battery-backup mode, this termi-
nal sources approximately 10µA from VOUT. Use BATT
ON to indicate battery-switchover status or to supply
base drive to an external pass transistor for higher-cur-
rent applications (see Typical Operating Circuit).
Input Supply Voltage
The Input Supply Voltage (VCC) should be a regulated
5V. VCC connects to VOUT via a parallel diode and a
large PMOS switch. The switch carries the entire cur-
rent load for currents less than 250mA. The parallel
diode carries any current in excess of 250mA. Both the
switch and the diode have impedances less than 1
each. The maximum continuous current is 250mA, but
power-on transients may reach a maximum of 1A.
MAX691A
MAX693A
MAX800L
MAX800M
PFI PFO
GND
+5V
VCC
VBATT
2.0V to 5.5V LOW BATT
Figure 6. CE Propagation Delay Test Circuit Figure 7. Low-Battery Indicator
PIN NAME STATUS
1 VBATT Supply current is 1µA max.
2 VOUT VOUT is connected to VBATT through an
internal PMOS switch.
3 VCC Battery switchover comparator monitors
VCC for active switchover.
4GND GND 0V, 0V reference for all signals.
5BATT ON Logic high. The open-circuit output is
equal to VOUT.
6LOWLINE Logic low*
7OSC IN OSC IN is ignored.
8OSC SEL OSC SEL is ignored.
9PFI
The power-fail comparator remains
active in the battery-backup mode for
VCC VBATT - 1.2V typ.
10 PFO
The power-fail comparator remains
active in the battery-backup mode for
VCC VBATT - 1.2V typ. Below this volt-
age, PFO is forced low.
11 WDI Watchdog is ignored.
12 CE OUT Logic high. The open-circuit voltage is
equal to VOUT.
13 CE IN High impedance
14 WDO Logic high. The open-circuit voltage is
equal to VOUT.
15 RESET Logic low*
16 RESET High impedance*
Table 2. Input and Output Status in Battery-Backup
Mode
* VCC must be below the reset threshold to enter battery-backup
mode.
MAX691A/MAX693A/MAX800L/MAX800M
Battery-Backup Input
The Battery-Backup Input (VBATT) is similar to the VCC
input except the PMOS switch and parallel diode are
much smaller. Accordingly, the on-resistances of the
diode and the switch are each approximately 10.
Continuous current should be limited to 25mA and
peak currents (only during power-up) limited to 250mA.
The reverse leakage of this input is less than 1µA over
temperature and supply voltage (Figure 8).
Output Supply Voltage
The Output Supply Voltage (VOUT) pin is internally con-
nected to the substrate of the IC and supplies current
to the external system and internal circuitry. All open-
circuit outputs will, for example, assume the VOUT volt-
age in their high states rather than the VCC voltage. At
the maximum source current of 250mA, VOUT will typi-
cally be 200mV below VCC. Decouple this terminal with
a 0.1µF capacitor.
__________Applications Information
The MAX691A/MAX693A/MAX800L/MAX800M are not
short-circuit protected. Shorting VOUT to ground, other
than power-up transients such as charging a decou-
pling capacitor, destroys the device.
All open-circuit outputs swing between VOUT and GND
rather than VCC and GND.
If long leads connect to the chip inputs, insure that
these leads are free from ringing and other conditions
that would forward bias the chip’s protection diodes.
There are three distinct modes of operation:
1) Normal operating mode with all circuitry powered
up. Typical supply current from VCC is 35µA while
only leakage currents flow from the battery.
2) Battery-backup mode where VCC is typically within
0.7V below VBATT. All circuitry is powered up
and the supply current from the battery is typically
less than 60µA.
3) Battery-backup mode where VCC is less than
VBATT by at least 0.7V. VBATT supply current is
1µA max.
Using SuperCap or MaxCap with the
MAX691A/MAX693A/MAX800L/MAX800M
VBATT has the same operating voltage range as VCC,
and the battery switchover threshold voltages are typi-
cally ±30mV centered at VBATT, allowing use of a
SuperCap and a simple charging circuit as a backup
source (Figure 9).
If VCC is above the reset threshold and VBATT is 0.5V
above VCC, current flows to VOUT and VCC from VBATT
until the voltage at VBATT is less than 0.5V above VCC.
For example, with a SuperCap connected to VBATT and
through a diode to VCC, if VCC quickly changes from 5.4V
to 4.9V, the capacitor discharges through VOUT and VCC
until VBATT reaches 5.1V typ. Leakage current through
the SuperCap charging diode and the internal power
diode eventually discharges the SuperCap to VCC. Also, if
VCC and VBATT start from 0.1V above the reset threshold
and power is lost at VCC, the SuperCap on VBATT dis-
charges through VCC until VBATT reaches the reset
threshold; then the battery-backup mode is initiated and
the current through VCC goes to zero.
Microprocessor Supervisory Circuits
12 ______________________________________________________________________________________
MAX691A
MAX693A
MAX800L
MAX800M
1
0.47F*
1N4148
+5V
2
3
VCC
GND
VBATT
4
VOUT
* MaxCap
Figure 8. VCC and VBATT to VOUT Switch Figure 9. SuperCap or MaxCap on VBATT
Using Separate Power Supplies
for VBATT and VCC
If using separate power supplies for VCC and VBATT,
VBATT must be less than 0.3V above VCC when VCC is
above the reset threshold. As described in the previ-
ous section, if VBATT exceeds this limit and power is
lost at VCC, current flows continuously from VBATT to
VCC via the VBATT-to-VOUT diode and the VOUT-to-VCC
switch until the circuit is broken (Figure 8).
Alternate Chip-Enable Gating
Using memory devices with both CE and CE inputs
allows the CE loop to be bypassed. To do this, con-
nect CE IN to ground, pull up CE OUT to VOUT, and
connect
CE OUT to the CE input of each memory
device (Figure 10). The CE input of each part then
connects directly to the chip-select logic, which does
not have to be gated.
Adding Hysteresis to the
Power-Fail Comparator
Hysteresis adds a noise margin to the power-fail com-
parator and prevents repeated triggering of PFO when
VIN is near the power-fail comparator trip point. Figure
11 shows how to add hysteresis to the power-fail com-
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
______________________________________________________________________________________ 13
MAX691A
MAX693A
MAX800L
MAX800M
VCC
GND
PFI
*OPTIONAL
R2
R3
R1
VIN +5V
C1*
TO µP
PFO
VTRIP = 1.25 R1 + R2
R2
VH = 1.25/ R2 I I R3 VL - 1.25 + 5 - 1.25 = 1.25
R1 + R2 I I R3 R1 R3 R2
PFO
5V
0V
0V VH
VTRIP
VIN
VL
Figure 10. Alternate CE Gating
Figure 12. Monitoring a Negative Voltage
Figure 11. Adding Hysteresis to the Power-Fail Comparator
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
14 ______________________________________________________________________________________
parator. Select the ratio of R1 and R2 such that PFI sees
1.25V when VIN falls to the desired trip point (VTRIP).
Resistor R3 adds hysteresis. It will typically be an order
of magnitude greater than R1 or R2. The current
through R1 and R2 should be at least 1µA to ensure that
the 25nA (max) PFI input current does not shift the trip
point. R3 should be larger than 10kto prevent it from
loading down the PFO pin. Capacitor C1 adds noise
rejection.
Monitoring a Negative Voltage
The power-fail comparator can be used to monitor a
negative supply voltage using Figure 12’s circuit. When
the negative supply is valid, PFO is low. When the neg-
ative supply voltage drops, PFO goes high. This cir-
cuit’s accuracy is affected by the PFI threshold
tolerance, the VCC voltage, and resistors R1 and R2.
Backup-Battery Replacement
The backup battery may be disconnected while VCC is
above the reset threshold. No precautions are neces-
sary to avoid spurious reset pulses.
Negative-Going VCC Transients
While issuing resets to the µP during power-up, power-
down, and brownout conditions, these supervisors are
relatively immune to short-duration, negative-going VCC
transients (glitches). It is usually undesirable to reset
the µP when VCC experiences only small glitches.
Figure 13 shows maximum transient duration vs. reset-
comparator overdrive, for which reset pulses are not
generated. The graph was produced using negative-
going VCC pulses, starting at 5V and ending below the
reset threshold by the magnitude indicated (reset com-
parator overdrive). The graph shows the maximum
pulse width a negative-going VCC transient may typical-
ly have without causing a reset pulse to be issued. As
the amplitude of the transient increases (i.e., goes far-
ther below the reset threshold), the maximum allowable
pulse width decreases. Typically, a VCC transient that
goes 100mV below the reset threshold and lasts for
40µs or less will not cause a reset pulse to be issued.
A 100nF bypass capacitor mounted close to the VCC
pin provides additional transient immunity.
Connecting a Timing Capacitor at OSC IN
When OSC SEL is connected to ground, OSC IN dis-
connects from its internal 10µA (typ) pull-up and is
internally connected to a ±100nA current source.
When a capacitor is connected from OSC IN to ground
(to select alternative reset and watchdog timeout peri-
ods), the current source charges and discharges the
timing capacitor to create the oscillator that controls the
reset and watchdog timeout period. To prevent timing
errors or oscillator start-up problems, minimize external
current leakage sources at this pin, and locate the
capacitor as close to OSC IN as possible. The sum of
PC-board leakage plus OSC capacitor leakage must be
small compared to ±100nA.
Figure 13. Maximum Transient Duration without Causing a
Reset Pulse vs. Reset Comparator Overdrive
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
______________________________________________________________________________________ 15
Maximum VCC Fall Time
The VCC fall time is limited by the propagation delay of
the battery switchover comparator and should not
exceed 0.03V/µs. A standard rule of thumb for filter
capacitance on most regulators is on the order of 100µF
per amp of current. When the power supply is shut off or
the main battery is disconnected, the associated initial
VCC fall rate is just the inverse or 1A/100µF = 0.01V/µs.
The VCC fall rate decreases with time as VCC falls expo-
nentially, which more than satisfies the maximum fall-time
requirement.
Watchdog Software Considerations
A way to help the watchdog timer keep a closer watch
on software execution involves setting and resetting the
watchdog input at different points in the program,
rather than “pulsing” the watchdog input high-low-high
or low-high-low. This technique avoids a “stuck” loop
where the watchdog timer continues to be reset within
the loop, keeping the watchdog from timing out. Figure
14 shows an example flow diagram where the I/O dri-
ving the watchdog input is set high at the beginning of
the program, set low at the beginning of every subrou-
tine or loop, then set high again when the program
returns to the beginning. If the program should “hang”
in any subroutine, the I/O is continually set low and the
watchdog timer is allowed to time out, causing a reset
or interrupt to be issued.
Figure 14. Watchdog Flow Diagram
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
16 ______________________________________________________________________________________
Ordering Information (continued)
PART
MAX693ACUE
MAX693ACSE
MAX693ACPE 0°C to +70°C
0°C to +70°C
0°C to +70°C
TEMP RANGE PIN-PACKAGE
16 TSSOP
16 Narrow SO
16 Plastic DIP
MAX693AC/D
MAX693AEJE -40°C to +85°C
0°C to +70°C Dice*
16 CERDIP
MAX693AEUE
MAX693AEWE -40°C to +85°C
-40°C to +85°C 16 TSSOP
16 Wide SO
MAX693AEPE -40°C to +85°C 16 Plastic SO
MAX693AMJE -55°C to +125°C 16 CERDIP
MAX800LCUE
MAX800LCSE
MAX800LEUE -40°C to +85°C
0°C to +70°C
0°C to +70°C 16 TSSOP
16 Narrow SO
16 TSSOP
MAX800LEPE
MAX800MCUE
MAX800MCSE
-40°C to +85°C 16 Plastic DIP
MAX800MEUE -40°C to +85°C
0°C to +70°C
0°C to +70°C 16 TSSOP
16 Narrow SO
16 TSSOP
MAX800MEPE -40°C to +85°C 16 Plastic DIP
*Dice are specified at TA= +25°C, DC parameters only.
Devices in PDIP, SO and TSSOP packages are available in both
leaded and lead-free packaging. Specify lead free by adding
the + symbol at the end of the part number when ordering.
Lead free not available for CERDIP package.
___________________Chip Topography
WDI
CE IN
CE OUT
VCC
GND
WDO
BATT ON
LOW LINE
VOUT VBATT RESET RESET
PFI PFO
OSC SEL
OSC IN
0.11"
(2.794mm)
0.07"
(1.778mm)
TRANSISTOR COUNT: 729
SUBSTRATE CONNECTED TO VOUT
MAX693ACWE 0°C to +70°C 16 Wide SO
MAX693AESE -40°C to +85°C 16 Narrow SO
MAX800MESE -40°C to +85°C 16 Narrow SO
MAX800MCPE 0°C to +70°C 16 Plastic DIP
MAX800LESE -40°C to +85°C 16 Narrow SO
MAX800LCPE 0°C to +70°C 16 Plastic DIP
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
______________________________________________________________________________________ 17
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066 1
1
G
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
18 ______________________________________________________________________________________
SOICN .EPS
PACKAGE OUTLINE, .150" SOIC
1
1
21-0041 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.010
0.069
0.019
0.157
0.010
INCHES
0.150
0.007
E
C
DIM
0.014
0.004
B
A1
MIN
0.053A
0.19
3.80 4.00
0.25
MILLIMETERS
0.10
0.35
1.35
MIN
0.49
0.25
MAX
1.75
0.050
0.016L0.40 1.27
0.3940.386D
D
MINDIM
D
INCHES
MAX
9.80 10.00
MILLIMETERS
MIN MAX
16 AC
0.337 0.344 AB8.758.55 14
0.189 0.197 AA5.004.80 8
NMS012
N
SIDE VIEW
H0.2440.228 5.80 6.20
e0.050 BSC 1.27 BSC
C
HE
eBA1
A
D
0-8
L
1
VARIATIONS:
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
MAX691A/MAX693A/MAX800L/MAX800M
Microprocessor Supervisory Circuits
SOICW.EPS
PACKAGE OUTLINE, .300" SOIC
1
1
21-0042 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.012
0.104
0.019
0.299
0.013
INCHES
0.291
0.009
E
C
DIM
0.014
0.004
B
A1
MIN
0.093A
0.23
7.40 7.60
0.32
MILLIMETERS
0.10
0.35
2.35
MIN
0.49
0.30
MAX
2.65
0.050
0.016L0.40 1.27
0.5120.496D
D
MINDIM
D
INCHES
MAX
12.60 13.00
MILLIMETERS
MIN MAX
20 AC
0.447 0.463 AB11.7511.35 18
0.398 0.413 AA10.5010.10 16
NMS013
SIDE VIEW
H0.4190.394 10.00 10.65
e0.050 1.27
D0.6140.598 15.20 2415.60 AD
D0.7130.697 17.70 2818.10 AE
H
E
N
D
A1
B
e
A
0-8
C
L
1
VARIATIONS:
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
19 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
©2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.
ENGLISH ???? ??? ???
WHAT'S NEW
PRODUCTS
SOLUTIONS
DESIGN
APPNOTES
SUPPORT
BUY
COMPANY
MEMBERS
MAX693A
Part Number Table
Notes:
See the MAX693A QuickView Data Sheet for further information on this product family or download the MAX693A
full data sheet (PDF, 584kB).
1.
Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.2.
Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one
business day.
3.
Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full
data sheet or Part Naming Conventions.
4.
* Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product
uses.
5.
Part Number
Free
Sample
Buy
Direct
Package:
TYPE PINS SIZE
DRAWING CODE/VAR *
Temp
RoHS/Lead-Free?
Materials Analysis
MAX693AESE-TG002
-40C to +85C
RoHS/Lead-Free: No
MAX693AEJE
Ceramic DIP;16 pin;.300"
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J16-3*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AMJE
Ceramic DIP;16 pin;.300"
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J16-3*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX693AC/D
RoHS/Lead-Free: No
MAX693ACPE
PDIP;16 pin;.300"
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P16-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACPE+
PDIP;16 pin;.300"
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P16+1*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AEPE
PDIP;16 pin;.300"
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P16-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AEPE+
PDIP;16 pin;.300"
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P16+1*
-40C to +85C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AESE-G002
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACWE+
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16+1*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693ACSE
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16-2*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACSE+
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16+2*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693ACSE+T
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16+2*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693ACSE-T
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16-2*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACWE-T
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACWE
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACWE+T
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16+1*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AEWE+T
-40C to +85C
RoHS/Lead-Free: Yes
MAX693AESE+
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16+2*
-40C to +85C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AEWE+
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16+1*
-40C to +85C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AEWE-T
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AEWE
SOIC;16 pin;.300"
Dwg: 21-0042B (PDF)
Use pkgcode/variation: W16-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AESE-T
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AESE
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AESE+T
SOIC;16 pin;.150"
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S16+2*
-40C to +85C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693ACUE+
TSSOP;16 pin;4.4mm
Dwg: 21-0066I (PDF)
Use pkgcode/variation: U16+1*
0C to +70C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693ACUE+T
0C to +70C
RoHS/Lead-Free: Yes
MAX693ACUE
TSSOP;16 pin;4.4mm
Dwg: 21-0066I (PDF)
Use pkgcode/variation: U16-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX693ACUE-T
0C to +70C
RoHS/Lead-Free: No
MAX693AEUE-T
-40C to +85C
RoHS/Lead-Free: No
MAX693AEUE
TSSOP;16 pin;4.4mm
Dwg: 21-0066I (PDF)
Use pkgcode/variation: U16-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX693AEUE+
TSSOP;16 pin;4.4mm
Dwg: 21-0066I (PDF)
Use pkgcode/variation: U16+1*
-40C to +85C
RoHS/Lead-Free: Yes
Materials Analysis
MAX693AEUE+T
-40C to +85C
RoHS/Lead-Free: Yes
Didn't Find What You Need?
CONTACT US: SEND US AN EMAIL
C opyright 2007 by M axim I ntegrated Products, Dallas Semiconduc tor Legal Notices Privacy P olicy