D-Sub DIN 41 652 * CECC 75 301-802 * IEC 60 807 Number of contacts 9--50 Press-in, straight without grounding press-in board locks No. of contacts Identification Performance levels Explanations see page 05.165 Other performance levels on request Part No. Performance level Performance level 3 2 Male connector D-Sub Flange height x = 5.7 mm metal shell with dimples 9 09 66 124 770 . 09 66 124 670 . 15 09 66 224 770 . 09 66 224 670 . 25 09 66 324 770 . 09 66 324 670 . 9 09 66 114 750 . 09 66 114 650 . 15 09 66 214 750 . 09 66 214 650 . 25 09 66 314 750 . 09 66 314 650 . 37 09 66 414 750 . 09 66 414 650 . 9 09 66 114 750 . 09 66 114 650 . 15 09 66 214 750 . 09 66 214 650 . 25 09 66 314 750 . 09 66 314 650 . 37 09 66 414 750 . 09 66 414 650 . 50 09 66 514 750 . 09 66 514 650 . Please insert digit for flange thread or fitted female screw locks o 3.1 mm hole M3 4-40 UNC fitted screw locks 4-40 UNC 1)41) 5 6 1)72) Female connector Flange height x = 5.7 mm metal shell Please insert digit for flange thread or fitted female screw locks o 3.1 mm hole 1)41) M3 5 4-40 UNC 6 fitted screw locks 4-40 UNC 1)72) Female connector Flange height x = 6 mm metal shell Please insert digit for flange thread or fitted female screw locks o 3.1 mm hole 1)01) M3 1 4-40 UNC 2 fitted screw locks 4-40 UNC 1)32) 05 168 1) Not normally kept in stock Fitted screw locks 4-40 UNC not normally kept in stock for performance level 3 Connector dimensions see page 05.169. Mating conditions see page 05.165. 2) D-Sub DIN 41 652 * CECC 75 301-802 * IEC 60 807 Number of contacts 9--50 Press-in, straight without grounding press-in board locks Drawing Dimensions in mm Male connector M3 or 4 - 40 UNC 9 - 25 contacts fitted screw locks 4 - 40 UNC D-Sub Identification mark for 5.7 mm version Mating face acc. to: DIN 41 652 * CECC 75 301-802 * IEC 60 807 No. 1 contact M3 or 4 - 40 UNC Female connector X Y 6.0 0.2 4.20 0.2 5.7 0.2 4.35 0.2 fitted screw locks 4 - 40 UNC 9 - 37 contacts mark for 5.7 mm version M3 or 4 - 40 UNC fitted screw locks 4 - 40 UNC Female connector 50 contacts Press-in pins from position 34 to 50 are reversed 180 degrees Mating face acc. to: DIN 41 652 * CECC 75 301-802 * IEC 60 807 No. 1 contact Board drillings 9-37 g h 31.00 24.90 a 4 x 2.74 = 10.96 3 x 2.74 = 8.22 15 39.30 33.20 7 x 2.74 = 19.18 6 x 2.74 = 16.44 25 53.10 47.00 12 x 2.76 = 33.12 11 x 2.76 = 30.36 9 b 37 69.65 63.55 18 x 2.76 = 49.68 17 x 2.76 = 46.92 50 67.00 61.10 16 x 2.76 = 44.16 15 x 2.76 = 41.40 50 05 169