CLD-DS61 Rev 6K Product family data sheet Cree(R) XLamp(R) XM-L2 LEDs Product Description FEATURES Table of Contents The XLamp(R) XM-L2 LED builds on the * Available in white, 70CRI white, Characteristics.........................................2 unprecedented performance of the original XM-L, increasing lumen output 80CRI white, 85CRI white and Flux Characteristics.................................3 90CRI white Relative Spectral Power Distribution......5 up to 20% while providing a single die * ANSIcompatible chromaticity bins Relative Flux vs. Junction Temperature.. 5 LED point source for precise optical * Binned at 85C Electrical Characteristics.........................6 control. The XM-L2 LED shares the same * Maximum drive current: 3000mA Relative Flux vs. Current..........................6 mechanical and optical footprint as the * Low thermal resistance: 2.5C/W Relative Chromaticity vs. Current............7 original XM-L, providing a seamless * Wide viewing angle: 125 Relative Chromaticity vs. Temperature...7 upgrade path and shortened design * Unlimited floor life at Typical Spatial Distribution......................8 cycle. 30C/85% RH * Reflow solderable - JEDEC XLamp XM-L2 LEDs are the ideal choice JSTD020C Thermal Design........................................8 Reflow Soldering Characteristics............9 Notes......................................................10 for lighting applications where high * Electrically neutral thermal path Mechanical Dimensions........................12 light output and maximum efficacy are * RoHS and REACh compliant Tape and Reel.........................................13 required, such as LED light bulbs, outdoor * UL recognized component Packaging...............................................14 lighting, portable lighting, indoor lighting (R) (E349212) www.cree.com/Xlamp and solar-powered lighting. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 XLamp (R) XM-L2 LED Characteristics Characteristics Unit Thermal resistance, junction to solder point C/W 2.5 degrees 125 mV/C -1.6 Viewing angle (FWHM) Temperature coefficient of voltage ESD withstand voltage (HBM per Mil-Std-883D) Minimum Typical Maximum V 8000 mA 3000 Reverse voltage V -5 Forward voltage (@ 700mA, 85C) V 2.85 Forward voltage (@ 1500mA, 85C) V 3.05 Forward voltage (@ 3000mA, 85C) V 3.3 LED junction temperature C DC forward current 3.15 150 Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 2 XLamp (R) XM-L2 LED Flux Characteristics (TJ = 85C) The following table provides several base order codes for XLamp XM-L2 LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XM LED Family Binning and Labeling document. CCT Range Color Min. Cool White Neutral White Warm White 70-CRI White 80-CRI White 85-CRI White 5000 K 3700 K 2600 K 3700 K 2600 K 2600 K Max. 8300 K 5000 K 3700 K 5000 K 4300 K 3200 K Minimum Luminous Flux (lm) @ 700mA Calculated Minimum Luminous Flux (lm) @ 85C** Group Flux (lm) @ 85C Flux (lm) @ 25C* 1000 mA 1500 mA 2000 mA Order Code T5 260 296 357 502 631 XMLBWT-00-0000-0000T5051 T6 280 318 385 541 679 XMLBWT-00-0000-0000T6051 U2 300 342 412 580 728 XMLBWT-00-0000-0000U2051 U3 320 364 439 618 776 XMLBWT-00-0000-0000U3051 T4 240 273 330 464 582 XMLBWT-00-0000-000LT40E4 T5 260 296 357 502 631 XMLBWT-00-0000-000LT50E4 T6 280 318 385 541 679 XMLBWT-00-0000-000LT60E4 U2 300 342 412 580 728 XMLBWT-00-0000-000LU20E4 T2 200 227 275 386 485 XMLBWT-00-0000-000LT20E7 T3 220 250 302 425 534 XMLBWT-00-0000-000LT30E7 T4 240 273 330 464 582 XMLBWT-00-0000-000LT40E7 T5 260 296 357 502 631 XMLBWT-00-0000-000LT50E7 T5 260 296 357 502 631 XMLBWT-00-0000-000BT50E3 T6 280 318 385 541 679 XMLBWT-00-0000-000BT60E3 U2 300 342 412 580 728 XMLBWT-00-0000-000BU20E3 U3 320 364 439 618 776 XMLBWT-00-0000-000BU30E3 T2 200 227 275 386 485 XMLBWT-00-0000-000HT20E7 T3 220 250 302 425 534 XMLBWT-00-0000-000HT30E7 T4 240 273 330 464 582 XMLBWT-00-0000-000HT40E7 T5 260 296 357 502 631 XMLBWT-00-0000-000HT50E7 S4 164 186 225 317 398 XMLBWT-00-0000-000PS40E7 S5 172 196 236 332 417 XMLBWT-00-0000-000PS50E7 S6 182 207 250 352 442 XMLBWT-00-0000-000PS60E7 T2 200 227 275 386 485 XMLBWT-00-0000-000PT20E7 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. See the Measurements section (page 10). * Typical CRI for Cool White (5000 K - 8300 K CCT) is 65. * Minimum CRI for 70-CRI White is 70. * Typical CRI for Neutral White (3700 K - 5000 K CCT) is 75. * Minimum CRI for 80-CRI White is 80. * Typical CRI for Warm White (2600 K - 3700 K CCT) is 80. * Minimum CRI for 85-CRI White is 85. * Minimum CRI for 90-CRI White is 90. * Flux values @ 25C are calculated and are for reference only. ** Calculated flux values at 1000mA, 1500mA and 2000mA are for reference only. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 3 XLamp (R) XM-L2 LED Flux Characteristics (TJ = 85C) - Continued CCT Range Color Min. 90-CRI White 2600 K Max. 3200 K Minimum Luminous Flux (lm) @ 700mA Calculated Minimum Luminous Flux (lm) @ 85C** Order Code Group Flux (lm) @ 85C Flux (lm) @ 25C* 1000 mA 1500 mA 2000 mA S4 164 186 225 317 398 XMLBWT-00-0000-000US40E7 S5 172 196 236 332 417 XMLBWT-00-0000-000US50E7 S6 182 207 250 352 442 XMLBWT-00-0000-000US60E7 T2 200 227 275 386 485 XMLBWT-00-0000-000UT20E7 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. See the Measurements section (page 10). * Typical CRI for Cool White (5000 K - 8300 K CCT) is 65. * Minimum CRI for 70-CRI White is 70. * Typical CRI for Neutral White (3700 K - 5000 K CCT) is 75. * Minimum CRI for 80-CRI White is 80. * Typical CRI for Warm White (2600 K - 3700 K CCT) is 80. * Minimum CRI for 85-CRI White is 85. * Minimum CRI for 90-CRI White is 90. * Flux values @ 25C are calculated and are for reference only. ** Calculated flux values at 1000mA, 1500mA and 2000mA are for reference only. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 4 XLamp (R) XM-L2 LED Relative Spectral Power Relative Spectral Power Distribution Relative Radiant Power (%) 100 80 60 5000 K - 8300 K CCT 3700 K - 5000 K CCT 2600 K - 3700 K CCT 40 20 0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF=700mA) 120 Relative Luminous Flux (%) 100 80 60 40 20 0 25 50 75 100 125 150 Junction Temperature (C) Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 5 XLamp (R) XM-L2 LED Electrical Characteristics (Tj = 85C) Electrical Characteristics (TJ = 85C) 3000 2800 2600 Forward Current (mA) 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 2.6 2.8 3.0 3.2 3.4 Forward Voltage (V) Relative Intensity vs. Current (Tj = 85C) Relative Flux vs. Current (TJ = 85C) 350 Relative Luminous Flux (%) 300 250 200 150 100 50 0 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 Forward Current (mA) Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 6 XLamp (R) XM-L2 LED Relative Chromaticity Vs. Current, WW Relative Chromaticity vs. Current (Warm White) 0.012 0.008 0.004 CCx 0.000 CCy -0.004 -0.008 -0.012 0 500 1000 1500 2000 2500 3000 Current (mA) Relative Chromaticity Vs. Temperature WW Relative Chromaticity vs. Temperature (Warm White) 0.012 0.008 0.004 CCx 0.000 CCy -0.004 -0.008 -0.012 25 50 75 100 125 150 Tsp (C) Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 7 XLamp (R) XM-L2 LED Typical Spatial Radiation Pattern Typical Spatial Distribution Relative Luminous Intensity (%) 100 80 60 40 20 -90 -70 -50 -30 -10 0 10 30 50 70 90 Angle () Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end Thermal Design Coolproduct White to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 3500 Maximum Current (mA) 3000 2500 2000 1500 Rj-a = 4C/W 1000 Rj-a = 7C/W Rj-a = 10C/W 500 0 Rj-a = 15C/W 0 20 40 60 80 100 120 140 160 Ambient Temperature (C) Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 8 XLamp (R) XM-L2 LED Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L2 LEDs to be compatible with JEDEC JSTD020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used, and therefore it is the lamp or luminaire manufacturer's responsibility to determine applicable soldering requirements. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25C to Peak Profile Feature Average Ramp-Up Rate (Tsmax to Tp) IPC/JEDEC J-STD-020C Time Lead-Free Solder 1.2C/second Preheat: Temperature Min (Tsmin) 120 C Preheat: Temperature Max (Tsmax) 170 C Preheat: Time (tsmin to tsmax) 65-150 seconds Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) 217 C 45-90 seconds Peak/Classification Temperature (Tp) 235 - 245 C Time Within 5C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 C/second Time 25C to Peak Temperature 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 9 XLamp (R) XM-L2 LED Notes Measurements The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree's control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended or provided as specifications. PreRelease Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree's pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree's lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XM-L2 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of 30 C/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Ecology section of the Cree website. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 10 XLamp (R) XM-L2 LED Notes - Continued UL(R) Recognized Component This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 11 XLamp (R) XM-L2 LED Mechanical Dimensions 6 5 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE 5COPIED, REPRODUCED OR DISCLOSED TO ANY 4 UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. REV Thermal vias, if present, are not shown on these drawings. 6 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. 3 3 2 1 4.78 REVISONS All measurements are .13 mm unless otherwise indicated. REV BY DESCRIPTION APP'D 3.78 DATE 3.02 2.78 4.78 D 5.00 3.78 3.02 .50 0.73 .50 2.78 5.00 .50 0.73 .50 5.00 5.00 4.78 R2.26 C R2.26 Bottom View Side View Top View .50 .80 .50 .50 .25 .50 B .80 .50 .50 .80 .25 4.78 .80 4.78 .25 4.78 4.78 .25 .97 2.78 2.78 RECOMMENDED PCB SOLDER PAD Recommended PCB4.78 Solder Pad Recommended Stencil Pattern UNLESS OTHERWISE SPECIFIED (Shaded Area Is Open) DIMENSIONS ARE IN RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) RECOMMENDED PCB SOLDER PAD THIRD ANGLE PROJECTION 6 5 MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY 4 .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 6 5 4 3 1.6 DATE DRAWN BY DATE -- .X .XX .XXX X -- APPROVED DATE -- -- MATERIAL -- TITLE D. CRO -- APPROVED 1.5 .75 .25 .5 -- Phone (919) 313-5300 Fax (919) 313-5558 FINAL PROTEC FINISH: OUTLINESURFACE DRAWING, 5050 XMLB 1.6 3 SIZE FINAL PROTECTIVE FINISH -- DRAWN BY CHECK 4600 Silicon Drive FOR SHEET METAL PARTS ONLY Durham, N.CMATERIAL 27703 THIRD ANGLE PROJECTION D. CRONIN 11/14/12 CHECK .13MM UNLESS O UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) ALL DIMENSIONS ARE .13MM UNLESS OTHERWISE NOTED .97 A 4.78 ALL DIMENSIONS ARE 4.78 4.78 SCALE C DRAWING NO. 2610-00032 SHEET 16.000 2 1 Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 12 OF 6 5 4 3 2.00[.079] 4.00[.157] 1 2 REVISIONS NOTICE EE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NTAINED WITHIN ARE THE PROPRIETARY AND NFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT Y NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY AUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT CREE INC. DESCRIPTION REV BY DATE APP'D POCKET SIZE +.10 +.0039 .0591 -.00 -.0000 [ ] Do1.50 P2 1.75[.069] E1 Po Ao - 5.40mm [.213"] Bo - 5.40mm [.213"] Ko - 3.35mm [.132"] Tape and Reel 3.0 XLamp (R) XM-L2 LED D 5.40[.213] Bo 3 12.00[.472] Component Handling Systems Standard. All Cree carrier tapes conform to EIA-481D, Automated 6 5 4 5.50[.217]F 6 5 4 NOMINAL C NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THETHIS PROPRIETARY ANDINFORMATION CREE CONFIDENTIAL. PLOT AND THE CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN AREOF THE PROPRIETARY AND MAY NOT BE COPIED, INFORMATION REPRODUCEDOF ORCREE, DISCLOSED TO PLOT ANY CONFIDENTIAL INC. THIS UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. D D 2.00[.079] 2.00[.079] P2 1.50[.059] 4.00[.157] D1 4.00[.157] Po 8.00[.315] P REVISIONS REVISIONS DESCRIPTION DESCRIPTION REV 3.0 B 6 7.0 5 C NOTICE NTIAL. THIS PLOT AND THE INFORMATION THIN ARE THE PROPRIETARY AND INFORMATION OF CREE, INC. THIS PLOT OPIED, REPRODUCED OR DISCLOSED TO ANY D PERSON WITHOUTTHE WRITTEN CONSENT 5.40[.213] 4 A B Ao B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .01 .XXX .005 X .5 FOR SHEET METAL PARTS ONLY .X .06 .XX .03 .XXX .010 X .5 SURFACE FINISH: 5 D 4 8 6 1 C BY DATE DDS 11/8/10 DC 2/26/12 BS 8.00[.315] DATE 8.00[.315] P TITLE P APPROVED SIZE A Loaded Pockets (1000 Lamps) A FINAL PROTECTIVE FINISH User Feed Direction REV. DRAWING NO. 2402-00011 7.0 SCALE DRAWING SCALE 2 SHEET 7.0 1 A OF 4 1.75 3.35[.132] 3.35[.132] 3 Ko Ko START 12 .36[.014] D T .36[.014] T A XM 5050 CARRIER TAPE MATERIAL 5.40[.213] 5.40[.213] Ao ANODE SIDE 1.50[.059] Phone (919) 313-5300 Fax (919) 313-5558 D1 1.50[.059] D1 B 3.35 2 1 2400-00009 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 INDEX QTY ITEM 1 1 2400-00009-CORE DRAWN BY COMMENTS DATE UNLESS OTHERWISE SPECIFIED DATE 4/23/10 2 D. CRONIN 2DRAWN BY2400-00009-REEL UNLESS ARE OTHERWISE SPECIFIED DIMENSIONS IN INCHES D. CRONIN 4/23/10 DATE DIMENSIONS ARE IN INCHESCHECK AND AFTER FINISH. CHECK DATE AND AFTERSPECIFIED: FINISH. TOLERANCE UNLESS TOLERANCE .XX UNLESS .01 SPECIFIED: APPROVED DATE TITLE .XX .01 .XXX .005 APPROVED DATE TITLE X .XXX .5 .005 THIRD ANGLE PROJECTION MATERIAL X PARTS .5 FOR SHEET METAL ONLY Leader THIRD ANGLE PROJECTION MATERIAL FOR.XSHEET METAL .06 PARTS ONLY DRAWING NO. 400mm (min.) of SIZE .XX .X .03 .06 DRAWING NO. SIZE FINAL PROTECTIVE FINISH .03 empty pockets with .XXX .XX .010 FINAL PROTECTIVE FINISH X .XXX .5 .010 at least 100mm SCALE X .5 SURFACE FINISH: 63 SCALE sealed by tape DRAWING SCALE SURFACE FINISH: 63 DRAWING SCALE Ao C 4600 Silicon Drive Durham, N.C 27703 4600 Silicon Drive Durham, N.C 27703 Phone (919) 313-5300 Phone (919) 313-5300 Fax (919) 313-5558 Fax (919) 313-5558 XMXM 5050 CARRIER TAPE 5050 CARRIER TAPE 2402-00011 A 2402-00011 A 6 (405 empty pockets min.) 4 5 3 4 2 3 A REV. A 6 SHEET OF SHEET 1 2 1OF / 1 1 D REV. A 1 /1 12.4 +.2 .0 MEASURED AT HUB C C 330 +.25 -.75 16.4 +0.2 .0 MEASURED AT HUB THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .25 .XXX .125 X .5 FOR SHEET METAL PARTS ONLY .X 1.5 .XX .75 .XXX .25 X .5 SURFACE FINISH: 5 4 1.6 3 1.9.4 DATE DRAWN BY D. CRONIN CHECK 21 .4 4600 Silicon Drive Durham, N.C 27703 06/08/10 DATE -- Phone (919) 313-5300 -- Fax (919) 313-5558 A DATE APPROVED -- -- MATERIAL TITLE 13.1 .2 -- SIZE FINAL PROTECTIVE FINISH -- SCALE XM LOADING SPEC REV. DRAWING NO. C 2402-00012 SHEET 3.000 2 B OF B 1 /1 1 12.4 +1.0 -.5 MEASURED AT EDGE 60 60 REVISONS REV DESCRIPTION BY DATE APP'D Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. UNLESS OTHERWISE SPECIFIED DRAWN BY A THIRD ANGLE PROJECTION B 1 /1 B B C APP'D 4600 Silicon Drive Durham, N.C 27703 4/23/10 DATE CATHODE SIDE 4 5 Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) D. CRONIN CHECK 3 A 6 D DATE DRAWN BY 63 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. D APP'D DATE APP'D CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 B END 2 BY 5.40[.213] 5.40[.213] Bo Bo 3.0 12.00[.472] 12.00[.472] NOMINAL NOMINAL REVISONS [.484] 10.25 12.30DESCRIPTION 12.30 [.484] MAX Loaded pocket count was 750 [.404]10.25 MAX [.404] WANODE E2 MADE CATHODE AND W NOTE LARGER E2 REV 3.35[.132] Ko THIRD ANGLE PROJECTION 6 5.50[.217]F 5.50[.217]F 3 C 1 DATE BoBo - - 5.40mm [.213"] 5.40mm [.213"] KoKo - - 3.35mm [.132"] 3.35mm [.132"] 1.75[.069] E1 1.75[.069] E1 .36[.014] T Po BY POCKET SIZE POCKET SIZE AoAo - - 5.40mm [.213"] 5.40mm [.213"] +.10 +.0039 Do1.50 .0591 +.0039 -.00 +.10 .0591 -.0000 [] Do1.50 -.00 -.0000 [ ] P2 1 2 Except as noted, all dimensions in mm. REV 12.30 [.484] MAX W 10.25 [.404] E2 2 3 DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX .01 .XXX .005 X .5 FOR SHEET METAL PARTS ONLY D. CRONIN CHECK DATE 4600 Silicon Drive Durham, N.C 27703 09/29/09 13 DATE -APPROVED -MATERIAL Phone (919) 313-5300 -- Fax (919) 313-5558 DATE -- TITLE REEL, 13" X 12MM, 3 PIECE SNAP A A XLamp (R) XM-L2 LED Packaging Humidity Indicator Card (inside bag) Dessicant (inside bag) Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Bin Code, Qty, Lot # Vacuum-Sealed Moisture Barrier Bag Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Label with Custo Code, Qty, Reel I Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID Patent Label Copyright (c) 2012-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R), the Cree logo and XLamp(R) are registered trademarks of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 14