Card Edge Connectors
Catalog 1654080 Issued 7-03
Card Edge Connectors
2
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Introduction
This catalog contains
product descriptions of
AMP Card Edge Connectors.
These connectors are pre-
sented in three groups:
Solder Type Board-to-
Board, Press-fit Board-to-
Board, and Wire-to-Board
connectors.
To assist you in the selec-
tion of the appropriate con-
nector for your application,
a selection guide is provid-
ed at the beginning of each
section. See the Table of
Contents on the following
page for the exact location.
A comprehensive descrip-
tion and features of a partic-
ular printed circuit board
connector family are
provided at the beginning
of that section. Various
technical documents are
referenced in the connector
family sections and are list-
ed and described at the
rear of this catalog.
The Tyco Electronics
products presented in this
catalog are designed and
manufactured according
to the highest possible
standards of quality and
craftsmanship. They offer
optimum reliability at the
lowest possible cost.
Dimensioning:
Dimensions are in inches and millimeters
unless specified otherwise. Values in
brackets are metric equivalents.
Metric symbols used are:
m (meter)
mm (millimeter)
mm2 (square millimeter)
kg (kilogram)
C (Celsius)
N (newton)
Note: Dimensions in this catalog are for
reference purposes only. Customer
drawings are available upon request.
© Copyright 1992, 1996 and 2002 by
Tyco Electronics. All Rights Reserved.
AMP, ACTION PIN, AMP-DURAGOLD,
AMP-LEAF, AMP-O-LECTRIC,
AMP-O-MATIC, AMPOMATOR,
AMP PACE, CERTI-CRIMP, DUO-TYNE,
ECONOMATE, TELEDENSITY, and TYCO
are trademarks.
Other products, logos, and company
names mentioned herein may be trade-
marks of their respective owners.
Produced under a Quality
Management System certified
to ISO 9001
A copy of the
certificate is available
upon request
Need more information?
Call Technical Support at
the numbers listed at the
bottom of the catalog
pages.
Technical Support is staffed
with specialists well versed
in Tyco Electronics prod-
ucts. They can provide you
with:
Technical Support
Catalogs
Technical Documents
Product Samples
Tyco Electronics
Authorized Distributor
Locations
Card Edge Connectors
3
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Table of Contents
Solder Type Board-to-Board Connectors
Introduction………………………………………………………………………………………2
Selection Guide ………………………………………………………………………………4-6
Standard Edge Series Connectors
Standard Edge .050 PCI Card Edge Connectors ………………………………………7-10
Standard Edge .050 Series Connectors ………………………………………………11-14
Standard Edge II Connectors ……………………………………………………………15-27
Cantilever Beam Dip Solder Tails Overview ……………………………………………………28
.100" [2.54] Centerline ……………………………………………………………………29-34
.125" [3.18] Centerline ……………………………………………………………………35-37
.156" [3.96] Centerline ……………………………………………………………………38-40
Modified Bellows Contact Overview ……………………………………………………………41
.100" [2.54] Centerline ……………………………………………………………………42-47
.125" [3.18] Centerline ……………………………………………………………………48-52
.156" [3.96] Centerline ……………………………………………………………………53-56
Polarization Keys ………………………………………………………………………………57
Standard Daughter Card Layout…………………………………………………………………57
Low Profile Connectors ……………………………………………………………………58-63
Twin Leaf Mother Board Connectors ………………………………………………………64-72
Rotary Cam ZIF Connectors …………………………………………………………………73-82
Linear ZIF Connectors ………………………………………………………………………83-96
Press-Fit Board-to-Board Connectors
ACTION PIN Press-Fit Contacts ……………………………………………………………97
AMP PACE Connectors …………………………………………………………………98-115
TELEDENSITY Connectors ……………………………………………………………116-118
ECONOMATE Connectors ……………………………………………………………119-126
Cantilever Beam Press-Fit Connectors Overview ……………………………………………127
.050" [1.27] High Density ………………………………………………………………128-129
.100" [2.54] Centerline …………………………………………………………………130-140
.125" [3.18] Centerline …………………………………………………………………141-144
.156" [3.96] Centerline …………………………………………………………………145-148
Application Tooling ……………………………………………………………………149-151
Wire-to-Board Connectors
Introduction …………………………………………………………………………………152
Selection Guide ………………………………………………………………………………153
Crimp Snap Twin Leaf Connectors …………………………………………………154-163
AMP-LEAF Connectors…………………………………………………………………164-172
High Current Connectors………………………………………………………………173-176
DUO-TYNE Flag Connectors …………………………………………………………177-180
Printed Circuit Board Connector Hood Assemblies ………………………………181-183
Application Tooling ……………………………………………………………………184,185
Technical Documents ……………………………………………………………………186,187
Part Number Index ………………………………………………………………………188-201
Tyco Electronics Related Product Information ………………………………………………202
Card Edge Connectors
Selection Guide, Board-to-Board Connectors
4
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
.050 [1.27] X X
.100 [2.54] X
.125 [3.18] X
.150 [3.81]
.156 [3.96]
Solder XXX
Right-Angle Solder X
Wrap-Type X
Card Extender X
Solder Eyelet
Press-Fit
Surface-Mount
Introduction
Board-to-board (mother/
daughter board) connectors
are ideally suited to back-
plane wiring or any other
application requiring the
circuit connection of one
printed circuit board to
another. Designed to
shorten manufacturing time
and reduce applied costs,
these one-step, pre-assem-
bled connectors are ready
for mounting and mass
insertion.
Many of the connectors are
available with the proven
and reliable ACTION PIN
contact. This unique con-
tact has superior electrical
and physical characteristics
that are top of the line in the
industry.
Board-to-board connectors
come in a range of contact
centerline spacings of .050
[1.27] to .156 [3.96]. A wide
range of dual position sizes
and post styles are avail-
able. One family of connec-
tors features zero insertion
force of the daughter
board, along with a choice
of actuating devices. A vari-
ety of housing and contact
materials further expands
the choice of connectors
available to meet many
application requirements.
To help in choosing a con-
nector for your application,
a Selection Guide is provid-
ed on pages 4 through 6.
Centerlines
Tail Styles
Standard Edge .050 Series
PCI Connectors
(Pages 7-10)
.610
[15.49]
.300
[7.62]
.170±.020
[4.32±0.51]
Standard Edge
.050 Series Connectors
(Pages 11-14)
.350
[8.89]
.610
[15.49]
.300
[7.62]
.170±.020
[4.32±0.51]
Standard Edge II Connectors
(.100 and .125 Centerline)
(Pages 15-27)
.155
[3.94]
.368
[9.35]
.315
[8.00]
.610
[15.49]
Card Edge Connectors
5
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Selection Guide, Board-to-Board Connectors (Continued)
Centerlines
Standard Edge II
Connectors (.150 Centerline)
(Pages 15-27)
.050 [1.27]
.0625 [1.588]
X X .100 [2.54]
X X .125 [3.18]
X.150 [3.81]
X X .156 [3.96]
Tail Styles
X X X Solder
Right-Angle Solder
Wrap-Type
Card Extender
Solder Eyelet
X X Press-Fit
Surface-Mount
Centerlines
.050 [1.27]
X X .100 [2.54]
X X X .125 [3.18]
X.150 [3.81]
X X X .156 [3.96]
Tail Styles
X X X Solder
XRight-Angle Solder
XWrap-Type
Card Extender
XSolder Eyelet
Press-Fit
Surface-Mount
Twin Leaf
Mother Board Connectors
(Pages 64-72)
.400
[10.16]
.150
[3.81]
.610
[15.49]
.235
[5.97]
.054–.070 [1.37-1.78]
.045
[1.14] .015
[0.33] .008
[.203]
.200
[.508]
.015
[0.41]
.200±.020
[5.08±0.51]
.365
[9.27]
.135±.020
[3.43±0.51]
Low Profile
Connectors
(Pages 58-63)
.125
[3.18]
.165
[4.19]
.437
[11.10]
.460
[11.68]
Cantilever Beam Connectors
Standard Housing
(Pages 28-40)
Cantilever Beam
Connectors Scoop Housing
(Pages 28-40)
Modified Bellows Connector
(Pages 41-56)
.368
[9.35]
.300
[7.62]
.054-.071
[1.37-1.80]
.200
[5.08]
.610
[15.49]
.025
[.63]
.370
[9.40] .390
[9.91]
.300
[7.62]
.610
[15.49] .705
[17.91]
.145
[3.68] .020±.010
[.51±.25] .054 to .071
[1.37 to 1.80]
.395 or .510
[10.03 or 12.95]
Card Edge Connectors
6
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
High Density Press Fit
Connector
For .093 Cards
(Pages 128-129)
.400
[10.16]
.066
[1.68]
.610
[15.49] .421
[10.69] .461
[11.71]
Selection Guide, Board-to-Board Connectors (Continued)
.050 [1.27] X
.0625 [1.588]
.100 [2.54] X X
.125 [3.18] X
.150 [3.81]
.156 [3.96] X X
Solder
Right-Angle Solder
Wrap-Type X
Card Extender
Solder Eyelet
Press-Fit XXX
Surface-Mount
Centerlines
Tail Styles
Centerlines
.050 [1.27]
.0625 [1.588]
.100 [2.54] XXX
.125 [3.18] XXX
.150 [3.81]
.156 [3.96] X
Tail Styles
Solder X X
Right-Angle Solder X
Wrap-Type X X X
Card Extender
Solder Eyelet
Press-Fit X X
Surface-Mount
Rotary Cam ZIF
Connectors
(Pages 73-82)
.440
[11.18]
.150
[3.81]
.848
[21.54]
.598
[15.19]
Linear ZIF
Connectors
(Pages 83-96)
.140
[3.56] .475 [12.07]
.450 [11.43]
.845 [21.46]
.815 [20.70]
.490 [12.45]
.460 [11.68] .370 [9.40]
.345 [8.76]
AMP PACE Connectors,
Card Scoop Housing
(Pages 98-115)
A
.234
[5.94] .645
[16.38]
.130
[3.30]
.100 x .200 = .390 [9.91]
A.125 x .125 = .420 [10.67]
.125 x .200 = .420 [10.67]
AMP PACE Connectors,
Standard Housing
(Pages 98-115)
A
.234
[5.94]
.545
[13.84]
.130
[3.30]
.100 x .100 = .380 [9.65]
.100 x .200 = .360 [9.14]
A.125 x .250 = .410 [10.41]
.156 x .200 = .360 [9.14]
ECONOMATE
Connectors
(Pages 119-126)
.181
[4.60]
.415
[10.54].545
[13.84]
7
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
Product Facts
High density .050 [1.27]
centerline contact spacing
Easy mating of high circuit
count daughter boards
Polarizing web for positive
board-to-connector
registration
Choice of plastic pylons or
metal holddowns
Connectors that support
PCI expansion cards are
derived from those on the
MicroChannel Architecture
(MCA) bus. The MCA con-
nectors are well defined
and have proven value and
reliability.
There are four connectors
that can be used depend-
ing upon the PCI implemen-
tation. The differences
between these connectors
are 32 bit and 64 bit, and
the 5 volt and 3.3 volt sig-
naling environments. PCI-X
is a version of PCI at 133
MHz which is under devel-
opment and employs stan-
dard PCI connectors. PCI-X
is limited to 1 slot versus 4
slots of PCI.
A key differentiates the sig-
naling environment voltages.
The same physical connec-
tor is used for the 32 bit sig-
naling environments. In one
orientation, the key accepts
5 volt boards. When rotated
180°, the connector
accepts 3.3 volt signaling
boards. The pin numbering
of the connector changes
for the different signaling
environments to maintain
the same relative position of
signals on the connector.
Performance Specifications:
Durability—Tested to 100 mating
cycles
Mating Force—8 oz [2.22 N] max. per
contact pair
Unmating Force—.5 oz [0.14 N] min.
per contact pair
Contact Resistance—20 milliohms
max. (initial) 30 milliohms max. (final)
Insulation Resistance
1000 megohms min.
Dielectric Withstanding Voltage
500 VAC (at sea level)
Capacitance—2 picofarads max.
Current Rating—1 ampere max.
Voltage Rating—203 VAC
Thermal Shock
–55°C to +85°C for 5 cycles
Mixed Flowing Gas—Class II with
mated board for 20 days
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
Qualification Test Report
501-203
8
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
64 Bit, 5 Volt Signaling
92 Dual Positions
with 3 Plastic Pylons or
3 Metal Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic 94V-0 rated, white
Contacts—Phosphor bronze, plated as
follows:
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
Part Numbers
W Contact 5 Volt
(Post Length) Finish 3 Plastic 3 Metal
Pylons Holddowns
.100 Plating B 145166-2
2.54 Plating C 145166-4 145169-4
.125
3.18 Plating C 145166-8 145169-8
Surface
Mount Plating C 145113-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid side
walls.
Notes: 2. Other connector sizes can be made available, consult Tyco
Electronics.
Plastic Pylons
Metal Holddowns
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.) .150
[3.81]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
5.040
[128.02]
.050
48 Spaces at [1.27] 31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
.300
[7.62]
.050
[1.27] Solder Tail C
(2 Plcs.) L
.610
[15.49]
See Note.
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
.050
48 Spaces at [1.27] 31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
Through
Hole Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
.078
[1.98]
Ref.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder
(2 Plcs.)Tail C
.300
[7.62]
L
9
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Part Numbers
WHousing Contact 2 Plastic 2 Metal
(Post Length) Material Finish Pylons Holddowns
.100 Plating A 145154-1 145167-1
Y Plating B 145154-2
2.54 Plating C 145154-4 145167-4
.118 ZPlating A 11299-1
3.00 Plating B 11299-6
.125
3.18 YPlating C 145154-8
Surface
Mount YPlating C 145098-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls.
Notes: 2. Other connector sizes can be made available, consult Tyco Electronics.
Standard Edge .050 Series PCI Card Edge Connectors
32 Bit, 3.3 and 5 Volt
Signaling
60 Dual Positions
with 2 Plastic Pylons or
2 Metal Holddowns
Material and Finish:
Housing Y—High temperature thermo-
plastic 94V-0 rated, white
Housing Z—Nylon 6/6, white
Contacts—Phosphor bronze, plated as
follows:
Plating A—Duplex plated gold flash in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder Tail C
(2 Plcs.)
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
3.340
[84.84]
.050
48 Spaces at [1.27]
10 Spaces
at .050
[1.27]
.078
[1.98]
Ref.
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder
(2 Plcs.)Tail C
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
.050
48 Spaces at [1.27]
10 Spaces
at .050
[1.27]
.075
[1.90]
(2 Plcs.)
Plastic Pylons
Metal Holddowns
Through
Hole
L
Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
10
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
64 Bit, 3.3 Volt Signaling
92 Dual Positions
with 3 Plastic Pylons or
3 Metal Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic 94V-0 rated, white
Contacts—Phosphor bronze, plated as
follows:
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
.050
[1.27] Solder Tail C
(2 Plcs.)
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
5.040
[128.02]
.050
48 Spaces at [1.27]
31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
Part Numbers
W Contact 3.3 Volt
(Post Length) Finish 3 Plastic 3 Metal
Pylons Holddowns
.100 Plating B 145168-2
2.54 Plating C 1-145165-4 145168-4
.125
3.18 Plating C 1-145165-8
Surface
Mount Plating C 145246-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid
side walls.
Notes: 2. Other connector sizes can be made available, consult Tyco
Electronics.
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
.300
[7.62]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.) .150
[3.81]
(2 Plcs.)
.078
[1.98]
Ref.
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
.050
48 Spaces at [1.27]
31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
.050
[1.27] Solder
(2 Plcs.)Tail C
L
Plastic Pylons
Metal Holddowns
Through
Hole Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
11
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Product Facts
High density .050 [1.27]
centerline spacing of
contacts
Easy mating of high-circuit
count daughter boards
Compatible with infrared
reflow (IR) soldering
techniques
Polarizing web for positive
board-to-connector
registration
Choice of plastic pylons or
metal holddowns
Recognized under the
Component Program of
Underwriter
Laboratories Inc.
File No. E28476
Certified by Canadian
Standards
Association,
File No. LR 7189
The need to conserve
space and pack more func-
tion into a given area has
demanded that .050 [1.27]
centerline spacing become
a reality. AMP Standard
Edge .050 Series connec-
tors are the ideal vehicle for
mother/daughter board
applications requiring this
real estate.
These rugged connectors
have two rows of contacts
on .050 [1.27] centerlines.
Polarizing webs provide
positive board-to-connector
registration, while insertion
force allows even high
circuit-count daughter
boards to mate easily. The
connectors accept .054 to
.070 [1.37 to 1.78] thick
daughter boards and fea-
ture an overstress protected
contact design.
AMP Standard Edge .050
Series connectors are ideal
for fast automated robotic
assembly with registration
features and dimensional
tolerancing for more accurate
pickup and placement, and
are packaged in robotics-
compatible trays.
Plastic guide posts or metal
holddowns align the con-
nector with the mother board
and retain it for soldering.
To make circuit routing easy,
connector solder posts are
arranged in a four-row .100
[2.54] staggered grid. High-
temperature tolerant mate-
rials promote that these
connectors withstand
infrared reflow (IR) solder-
ing, while standoffs ease
flux cleaning.
Performance Specifications:
Contact Current Rating* —1 ampere
Termination Resistance
20 milliohms max. (initial)
30 milliohms max. (final)
Dielectric Withstanding Voltage
500 VAC min.
Insulation Resistance — 1000
megohms min.
Mating Force — .5 oz. [0.14 N] per
contact pair
Unmating Force — 1 oz. [0.3 N] per
contact pair
Durability (Tested to) — 100 mating
cycles
Application Temperature
+215°C for 120 seconds max.
Temperature Range
–55°C to +85°C
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
High Density for DataBus
Applications
®
12
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Configuration;
1 Key—2 Plastic Pylons
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Related Product Data:
Performance Specifications
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.060
[1.52] Typ.
.016
[0.41] Typ.
.170±.020
[4.32±0.51]
W
(Post
Length)
.300
[7.62]
.610
[15.49]
Section L-L
.035
[0.89]
(2 Plcs.)
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
35°
(2 Plcs.)
L
L
C
.075
[1.90]
(2 Plcs.)
.012
[0.30]
Typ.
A Spaces
at .050
[1.27]
B Spaces
at .050
[1.27]
No. of Dimensions W PC Board
Dual (Post Hole Connector
Positions ABC Length) Layout Part Numbers
1.490 .100
23 10 11 37.85 2.54 A0-650090-7
1.840 .100
30 10 18 46.74 2.54 B0-650090-6
.100
2.340 2.54 B0-650090-3
40 10 28 59.44 .140
3.56 B0-650181-2
2.590 .100
45 10 33 65.79 2.54 A0-650090-2
.100
3.140 2.54 B10-650090-11
56 10 44 79.76 .140
3.56 B0-650181-1
4.340 .100
80 37 41 110.24 2.54 C0-650090-9
.100
4.890 2.54 A10-650092-12
91 41 48 124.21 .140
3.56 A0-650092-2
1 Connector used for VLLocal Bus and MCA Bus applications.
2 Connector used for MCA Bus applications.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. .125 [3.18] post length is available, consult Tyco Electronics.
13
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Configuration;
1 Key—2 Plastic Pylons
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire
contact underplated .000050 [0.00127]
min. nickel
Related Product Data:
Performance Specifications
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.060
[1.52] Typ.
.016
[0.41] Typ.
.096
[2.44]Dia. Max.
.170±.020
[4.32±0.51]
W
(Post
Length)
.300
[7.62]
.610
[15.49]
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
35°
(2 Plcs.)
L
L
D
.075
[1.90]
(2 Plcs.)
.012
[0.30]
Typ.
A Spaces
at .050
[1.27]
B Spaces
at .050
[1.27]
No. of Dimensions W PC Board
Dual (Post Hole Connector
Positions ABCDLength) Layout Part Numbers
.100
3.740 2.54 A1650091-1*
66 10 44 9 95.00 .140
3.56 A 650091-2
*Connectors used for MCA Bus applications.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. .125 [3.18] post length is available, consult Tyco Electronics.
C Spaces
at .050
[1.27]
14
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Configuration; End Key
Standard Edge .050 Series Connectors
Configuration;
1 Key/1 Web —3 Metal
Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Holddowns—Brass, plated .000150
[0.00381] min. tin-lead over .000050
[0.00127] min. nickel
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire
contact underplated .000050 [0.00127]
min. nickel
Related Product Data:
Performance Specifications
page 11
Technical Documents:
Product Specification
104-14034
Application Specification
114-26012
.060
[1.52] Typ.
.350
[8.89]
6.440
[163.58]
.610
[15.49]
Section L-L
.035
[0.89]
(2 Plcs.) 35°
(2 Plcs.)
L
L
.075
[1.90]
(2 Plcs.)
W
(Post
Length)
10Spaces
at .050
[1.27]
63 Spaces
at .050
[1.27]
44Spaces
at .050
[1.27]
.150
[3.81]
(2 Plcs.)
.150
[3.81]
.300
[7.62]
.170±.020
[4.32±0.51]
.180
[4.57]
.050
[1.27] Solder Tail C
(2 Plcs.) L
120 Dual Positions
No. of W Connector
Dual (Post Part
Positions Length) Numbers
120 .140
3.56 145031-3
Note: Other connector sizes can be made available, consult Tyco Electronics.
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Related Product Data:
Performance Specifications
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
No. of Dimensions
Dual Post Connector
Positions A B C D Length Part Numbers
1.480 1.350 1.310 .100
25 24 37.59 34.29 33.27 2.54 650719-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section L-L
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
.170±.020
[4.32±0.51]
.300
[7.62]
.610
[15.49]
.075
[1.90]
.350
[8.89]
Post Length
35°
.035
[0.89]
.096
[2.44]
Dia.
Max.
.099
[2.52]
Max.
.012
[0.30] Typ.
.060
[1.52] Typ.
.016
[0.41] Typ.
L
B
L
ASpaces
at .050
[1.27]
15
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors
Product Facts
Maximum number
of dual positions
.100 [2.54] Centerlines-70,
.125 [3.18] Centerlines-50,
.150 [3.81] Centerlines-31
Selective gold plating of
contacts for high perfor-
mance at low cost
.025 [0.64] square solid
posts meet standard wrap-
type specifications
For flow solder applications
Glass-filled polyester
housing is 94V-0 rated
Accepts double sided
PC boards, .054-.070
[1.27-1.78] thick
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
Certified by Canadian
Standards
Association,
File No. LR 7189
AMP Standard Edge II
Connectors provide high
reliability and economy in
packages compatible with
industry standards for dou-
ble sided printed circuit
boards.
Tyco Electronics offers
Standard Edge II
Connectors with or without
mounting ears, for rack
mounting and soldering.
Contacts are arranged on
.100 [2.54] centers, .125
[3.18] centers, .150 [3.81]
centers, .200 [5.08]
row-to-row; and .250 [6.35]
row-to-row.
Right-angle connectors are
also available with contacts
arranged on .100 [2.54]
centers, .150 [3.81]
row-to-row or .200 [5.08]
row-to-row.
Card extenders with con-
tacts on .100 [2.54] and
.125 [3.18] centers also are
available.
Precision formed phosphor
bronze contacts are selec-
tively gold plated. Phosphor
bronze has excellent
strength characteristics
which help the connector
absorb load deflection
movement of a PC board
while maintaining sufficient
contact force for good elec-
trical connection. Bifurcated
cantilever beam contacts
provide redundant contact.
Performance Specifications
Contact Rating*: 3 amperes
continuous (UL and CSA)
Contact Resistance: 10 milliohms
max.
Operating Temperature: –55°C to
+85°C
Voltage Rating (Sea Level):
.100 [2.54] centerline—1000 VAC (test)
.125 [3.18] centerline—1500 VAC (test)
.150 [3.81] centerline—1500 VAC (test)
Insulation Resistance: 5000
megohms min., after exposure to
humidity
Vibration Tolerance: 10 to 500 hertz
Contact Engagement Force: 12 oz
[3.3 N] average per pair with .062 [1.57]
PC board
Contact Separation Force: 2 oz
[0.6 N] average per pair with .062 [1.57]
PC board
Humidity Tolerance: 90%-95% for
96 hours
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
16
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors Styles
.100 [2.54] and .125 [3.18] Centerline Solder Posts
without Mounting Ears
Pages 17 and 18
.100 [2.54] and .125 [3.18] Centerline Solder Posts
with Low and Mid-High Mounting Ears
Page 20
.100 [2.54] and .125 [3.18] Centerline Wrap-Type Posts
with Mid-High Mounting Ears
Page 21 .100 [2.54] Centerline Solder Posts with Board
Retention Feature, without Mounting Ears
Page 24
.100 [2.54] and .125 [3.18] Centerline
Card Extenders
Page 22
.150 [3.81] Centerline Solder Posts (with Board
Retention Feature), without Mounting Ears
Page 19
.100 [2.54] Centerline Right-Angle Posts
with Low and No Mounting Ears
Page 23
17
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline,
Vertical Solder Posts,
Without Mounting Ears
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating C—Gold flash in contact area,
tin on posts, with entire contact nickel
underplated
Technical Documents:
Product Specification
108-9039
Material:
Natural color polyester
Intercontact Keying Plug
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Dimensions Post Part Numbers
Dual
Positions A B C** D Length* Plating A Plating B Plating C
.560 .450 Open .200
314.22 11.43 End 5.08 .125 10-650263-11
.860 .750 .700 .500 .125 7-530843-5
621.84 19.05 17.78 12.70 .187 7-530843-6
1.260 1.150 1.100 .900 .125 5-530843-0
10 32.00 29.21 27.94 22.86 .187 4-530843-9
1.460 1.350 1.300 1.100 .125 0-530843-112 37.08 34.29 33.02 27.94
1.760 1.650 1.600 1.400 .125 0-530843-215 44.70 41.91 40.64 35.56
1.960 1.850 1.800 1.600
17 49.78 46.99 45.72 40.64 .125 5-530843-3
2.060 1.950 1.900 1.700
18 52.32 49.53 48.26 43.18 .125 0-530843-3 2-530843-7 1176137-11
2.260 2.150 2.100 1.900
20 57.40 54.61 53.34 48.26 .125 5-530843-4
2.460 2.350 2.300 2.100 .125 0-530843-422 62.48 59.69 58.42 53.34
2.760 2.650 2.600 2.400 .125 0-530843-525 70.10 67.31 66.04 60.96
3.060 2.950 2.900 2.700
28 77.72 74.93 73.66 68.58 .125 0-530843-6
3.260 3.150 3.100 2.900 .125 0-530843-7
30 82.80 80.01 78.74 73.66 .187 1-530843-8
3.360 3.250 3.200 3.000 7-530843-031 85.34 82.55 81.28 76.20 .125 6-530843-5
3.860 3.750 3.700 3.500 .125 0-530843-836 98.04 95.25 93.98 88.90
4.260 4.150 4.100 3.900
40 108.20 105.41 104.14 99.06 .187 2-530843-0
5.260 5.150 5.100 4.900 .125 1-530843-1
50 133.60 130.81 129.54 124.46
**Metric equivalent for post lengths are .125 = 3.18; .187 = 4.75.
**Cdimension is card slot length.
1 Connectors with Retention Feature.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
Retention Feature
(Open End Card Slot)
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.100
[2.54]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.295
[7.49]
.155
[3.94]
.191
[4.85]
Post
Length
.100
[2.54] Typ.
Intercontact Key Slot
.368
[9.35]
D
A
B
C**
18
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.125 [3.18] Centerline,
Vertical Solder Posts,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-1
(.125 [3.18] Centerline)
No. of Dimensions Post
Dual Part Numbers
Positions A B C** D Length*
1.035 .875 .875 .625
626.29 22.22 22.22 15.88 .125 650207-11
2.035 1.875 1.875 1.625
14 51.69 47.62 47.62 41.28 .187 5-530844-8
2.535 2.375 2.375 2.125
18 64.39 60.33 60.33 53.98 .187 1-530844-5
3.035 2.875 2.875 2.625
22 77.09 73.03 73.03 66.68 .187 1-530844-6
3.785 3.625 3.625 3.375
28 96.14 92.08 92.08 85.73 .187 1-530844-7
4.035 3.875 3.875 3.625
30 102.49 98.42 98.42 92.08 .187 1-530844-8
4.785 4.625 4.625 4.375
36 121.54 117.48 117.48 111.13 .187 1-530844-9
5.285 5.125 5.125 4.875
40 134.24 130.18 130.18 123.82 .187 2-530844-0
5.660 5.500 5.500 5.250
43 143.76 139.70 139.70 133.35 .125 1-530844-0
6.535 6.375 6.375 6.125 .125 1-530844-1
50 165.99 161.93 161.93 155.58 .187 2-530844-2
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Retention Feature
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.125
[3.18]
Intercontact Key Slot
.368
[9.35]
D
C**
Accepts
.054/.070
[1.37/1.77]
PC Board
.191/.203
[4.85/5.16]
.295
[7.49]
.155
[3.94]
.241
[6.11]
Post
Length
.610
[15.49]
.125
[3.18]
.550
[13.97]
.060
[1.52]
A
B
19
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.150 [3.81] Centerline,
Vertical Solder Posts,
Retention Feature, Without
Mounting Ears
No. of Dimensions Retention Post Part
Dual Location Numbers
Positions A B Length*
1.650 1.920 7-10,
12 41.91 48.77 15-18 .135 1-650728-2
2.700 2.970 7-10,
19 68.58 75.44 29-32 .135 1-650728-9
4.050 4.320 7-10,
28 102.87 109.73 25-32,47-50 .135 2-650728-9
4.500 4.770 7-10,
31 114.30 121.16 27-34,53-56 .135 3-650728-1
**Metric equivalent for post length is .135 = [3.43]
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
B±.010
[±0.25]
Inter-Contact
Keying Slot
.600
[15.21]
.025
[0.63]
Spaces at .150 = Dim A Ref.
[3.81]
.024 [0.61]
.020 [0.51]
.305
[9.27]
Card Slot Accepts
.054-.070 [1.37-1.78]
Printed Circuit Board
.045 [1.14]
Contact
Area
.015
[0.38]
.080
[.203]
Lead in
Area
.200±.020
[5.08±0.51]
.016 [0.41]
.020 [0.51]
.200
[5.08]
.035±.020
[3.430±0.51]
.432
[10.97]
+.005
-.010
+0.13
-0.25
0.143–.161
[3.63–4.03]
20
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
1.760 1.650 1.600 1.400 2.385 2.075 .100 .100 .191
15 44.70 41.91 40.64 35.56 67.18 52.71 2.54 2.54 4.85 .125 0-530841-2
2.060 1.950 1.900 1.700 2.645 2.375 .100 .100 .191
18 52.32 49.53 48.26 43.18 67.18 60.32 2.54 2.54 4.85 .125 0-530841-3
2.760 2.650 2.600 2.400 3.345 3.075 .100 .100 .191 .125 0-530841-5
25 70.10 67.31 66.04 60.96 84.96 78.11 2.54 2.54 4.85 .187 1-530841-6
3.260 3.160 3.100 2.900 3.845 3.575 .100 .100 .191
30 82.80 80.01 78.74 73.66 97.66 90.81 2.54 2.54 4.85 .187 1-530841-8
3.860 3.750 3.700 3.500 4.445 4.175 .100 .100 .191
36 98.04 95.25 93.98 88.90 112.90 106.21 2.54 2.54 4.85 .125 0-530841-8
.191 .125 1-530841-1
5.260 5.150 5.100 4.900 5.845 5.575 .100 .100 4.85 .187 2-530841-2
50 133.60 130.81 129.54 124.46 148.46 141.60 2.54 2.54 .141-.153
3.58-3.88 .125 0-650718-11, 2
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
2Connector with Mid-High Mounting Ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
1.035 .875 .875 .625 1.555 1.295 .125 .125 .241
626.29 22.22 22.22 15.88 39.50 32.89 3.18 3.18 6.11 .125 1-531341-3
.241
3.785 3.505 3.625 3.375 4.305 4.045 .125 .125 6.11 .187 1-530842-7
28 96.14 89.03 92.08 85.73 109.35 102.74 3.18 3.18 .241
6.11 .187 23-531341-02
6.535 6.255 6.375 6.125 7.055 6.795 .125 .125 .241
50 165.99 158.88 161.93 155.58 179.20 172.59 3.18 3.18 6.11 .125 1-530842-1
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
2Connector with Mid-High Mounting Ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
.100 [2.54] Centerline
.125 [3.18] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.100 [2.54] and .125 [3.18]
Centerline, Vertical Solder
Posts, Low and Mid-High
Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plugs
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-2
(.100 [2.54] Centerline)
Part No. 650025-1
(.125 [3.18] Centerline)
Low Mounting Ears
Mid-High Mounting Ears Retention Feature
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.150
[3.81]
.300
[7.62]
HG
F
A
J
D
C**
.360
[9.14]
.250
[6.35]
.250
[6.35]
.180
[4.57]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.295
[7.49]
.155
[3.94]
Post
Length
E
B
21
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
3.260 3.150 3.100 2.900 3.845 3.575 .100 .100 .200
30 82.80 80.01 78.74 73.66 97.41 90.80 2.54 2.54 5.08 .570 3-530396-3
3.860 3.750 3.700 3.500 4.435 4.175 .100 .100 .200
36 98.04 95.25 93.98 88.90 112.65 106.04 2.54 2.54 5.08 .570 3-530396-4
4.260 4.150 4.100 3.900 4.845 4.575 .100 .100 .200
40 108.20 105.41 104.14 99.06 123.06 116.21 2.54 2.54 5.08 .570 3-530396-4
**Metric equivalent for post length is .570 = [14.48].
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
**Metric equivalent for post length is .570 = [14.48].
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
3.035 2.755 2.875 2.625 3.555 3.295 .125 .125 .250
22 77.09 69.98 73.02 66.67 90.30 83.69 3.18 3.18 6.35 .570 4-530825-5
.100 [2.54] Centerline
.125 [3.18] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.100 [2.54] and .125 [3.18]
Centerline, Vertical Wrap-
Type Posts, Mid-High
Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plugs
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-2
(.100 [2.54] Centerline)
Part No. 650025-1
(.125 [3.18] Centerline)
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.150
[3.81]
.300
[7.62]
H
G
F
D
C
A
J
.180
[4.57]
.250
[6.35]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board .295
[7.49]
.155
[3.94]
Post
Length
E
B
22
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions
Dual
Positions A B C** D E F G H Part Numbers
5.260 5.160 5.100 4.900 5.845 5.575 .100 .100
50 133.60 130.81 129.54 124.46 148.46 141.60 2.54 2.54 530826-3
*Cdimension is card slot length.
1No mounting ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
.100 [2.54] Centerline
.125 [3.18] Centerline
.100 [2.54] and .125 [3.18]
Centerlines, Card Extender
Contacts
Material:
Natural color polyester
Intercontact Keying Plugs
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Material:
Natural color nylon
Mounting Block
Part No. 650025-1
(.125 [3.18] Centerline)
Kit Part No.531250-4
Each kit includes 2 mounting blocks,
2 self tapping screws, #5 x .437
[11.10] and 2 roll pins, .075 x .250
[1.57 x 6.35]
No. of Dimensions
Dual
Positions A B C** D E F G H Part Numbers
4.785 4.505 4.625 4.375 5.035 5.045 .125 .125
36 121.54 114.43 117.48 111.13 134.75 128.14 3.18 3.18 530384-2
*Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.062
[1.57] Dia.
Roll Pin
.150
[3.81]
.300
[7.62]
HG
F
D
C
A
.180
[4.67]
.250
[6.35]
.062
[1.57]
PC Board Ref.
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
Fits
.054/.070
[1.37/1.77]
PC Board
.295
[7.49]
.340
[8.63]
.155
[3.94]
.180
[4.57]
E
B
Card Extender
Connector
Housing Ref. #5 Self
Tapping
Screws
Mounting
Block
Part Number 650025-2
(.100 [2.54] Centerline)
23
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Right-Angle
Solder Posts, with Low and
No Mounting Ears
Low Mounting Ears
No Mounting Ears
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Related Product Data:
Performance Specifications
page 15
Technical Documents:
Product Specification
108-9039
Material:
Natural color polyester
Intercontact Keying Plug
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Dimensions Post Part Numbers
Dual
Positions A B C* D E F G1Length2(Plating A)
1.460 1.350 1.300 1.100 2.045 1.775 x.100x
12 37.08 34.29 33.02 27.94 51.94 45.08 .150 .090 3145089-13
2.060 1.950 1.900 1.700 2.645 2.375 x.100x
18 52.32 49.53 48.26 43.18 67.18 60.32 .150 .090 645384-1
2.260 2.150 2.100 1.900 2.845 2.575 x.100x
20 57.40 54.61 53.34 48.26 72.30 65.40 .150 .090 645384-3
*Cdimension is card slot length.
1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08].
2 Metric equivalent for post length is .090 = [2.27].
3 Connector with Board Locks.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part Numbers
Dual
Positions A B C* D G1Length2Plating A Plating B
1.760 1.650 1.600 1.400 .100x
15 44.70 41.91 40.64 35.56 .150 .090 650118-1
1.960 1.850 1.800 1.600 .100x
17 49.78 46.99 45.72 40.64 .200 .090 650187-1
2.760 2.350 2.600 2.400 .100x
25 70.10 67.61 66.04 60.96 .150 .090 532600-2
3.360 3.250 3.200 3.000 .100x
31 85.34 82.55 81.28 76.20 .150 .090 532600-4
3.460 3.350 3.300 3.100 .100x
32 87.88 85.09 83.82 78.74 .150 .090 532600-5
2.160 2.750 2.700 1.800 .100x
19 54.86 69.85 68.58 45.72 .150 .090 532600-6
*Cdimension is card slot length.
1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08].
2 Metric equivalent for post length is .090 = [2.27].
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
Low Mounting Ears
With Board Locks
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.295
[7.49]
.295
[7.49]
G
G
F
D
C
A
.300
[7.62]
.250
[6.25]
.610
[15.49] .550
[13.97]
.100
[2.54]
.100
[2.54]
Accepts
.054/.070
[1.37/1.77]
PC Board
Accepts
.054/.070
[1.37/1.77]
PC Board
Post
Length
Post
Length
.155
[3.94]
.155
[3.94]
.080
[1.82]
E
B
24
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline
Vertical Solder Posts,
Retention Feature,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating C—Gold flash in contact area,
tin on posts, with entire contact nickel
underplated
Technical Documents:
Product Specification
108-9039
Part Number 650025-2
(.100 [2.54] Centerline)
Retention Feature
No. of Dimensions Post Retention PartNumbers
Dual
Positions A B C** D Length* Feature Plating A
2.060 1.950 1.900 1.700
18 52.32 49.53 48.26 43.18 .125 3-6, 31-34 1-645235-4
3.360 3.250 3.200 3.000 3-6, 29-32 or
31 85.34 82.55 81.28 76.20 .125 31-34, 57-60 1-645235-1
5.260 5.150 5.100 4.900 3-6, 49-52,
50 133.60 130.81 129.54 124.46 .125 95-98 1-645235-3
6.260 6.150 6.100 5.900 3-6, 55-58,
60 159.00 156.21 154.94 149.86 .125 63-66, 115-118 1-645235-8
**Metric equivalent for post length is .125 = [3.18].
**Cdimension is card slot length.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.295
[7.49]
.191
[4.85]
D
C
A
.610
[15.49] .550
[13.97]
.100
[2.54]
.100
[2.54] Typ.
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
Post
Length
.155
[3.94]
.060
[1.52]
B
25
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline,
Special 18/31 Dual
Combination Connector,
Vertical Solder Posts,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated, except where noted
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area (except where noted), tin on posts,
with entire contact nickel underplated
Technical Documents:
Product Specification
108-9039
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Post Dimension Retention
Dual Part Numbers
Positions Type A Feature
.125 3-6, 41, 42, 645169-2
52 Solder Posts 3.18 51, 52, 93-96 1536128-11
.125
52 Solder Posts 3.18 None 645169-3
.125 3-14, 41, 42,
52 Solder Posts 3.18 51, 52, 85-96 645169-4
.125 5, 6, 31, 32, 2176139-12
52 Solder Posts 3.18 41, 42, 93, 94 2
.187
52 Solder Posts 4.75 None 650616-1
1 Housing material is high temperature glass-filled polyester, gray.
2 Contact area is gold flash.
Notes: 1. Card slot length is 5.300 [134.62].
2. Other connector sizes can be made available, consult
Tyco Electronics.
3. High temperature IR reflow compatible connectors can be
made available, consult Tyco Electronics.
Retention Feature
Solder Posts
.368
[9.35]
.295
[7.49]
.200
[5.08]
AA
.610
[15.49] .550
[13.97]
.100
[2.54] 1.900
[48.26] 3.200
[81.28]
5.460
[138.68]
5.350
[135.89]
.191
[4.85]
.100
[2.54]
.400
[10.16]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.060
[1.52]
26
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Recommended
PC Board Hole Layouts
Vertical Post Connectors
Right-Angle Post Connectors
Dimensions
Connector Type A B C D F
.100 .200 .040
Solder Post/Retention 2.54 5.08 1.02 See Note 1 See Note 2
.150 .200 .040
Solder Post/Retention 3.81 5.08 1.02 See Note 4 See Note 2
.125 .250 .040
Solder Post, Mounting Ears 3.18 6.35 1.02 See Note 3 See Note 3
.100/.125 .200/.250 .040
Solder Post, W/O Mounting Ears 2.54/3.18 5.08/6.35 1.02 See Note 4 See Note 2
.100 .200 .042
Wrap-Type Post 2.54 5.08 1.07 See Note 5 See Note 5
.125 .250 .042
Wrap-Type Post 3.18 6.35 1.07 See Note 5 See Note 5
Notes: 1. Refer to page 24 for DDimensions and Dual Positions.
2. No mounting ears. Dimensions do not apply.
3. Refer to page 20 for Dand FDimensions and Dual Positions.
4. Refer to pages 18 and 19 for DDimensions and Dual Positions.
5. Refer to page 21 for Dand FDimensions and Dual Positions.
Notes: 1. Refer to page 23 for Dand FDimensions and Dual Positions.
2. Refer to page 23 for DDimensions and Dual Positions.
3. No Mounting Ears, Dimensions do not apply.
Dimensions
Connector Type A B C D F G
.100 .150 .042 .137
Right-Angle Posts, Mounting Ears 2.54 3.81 1.07 See Note 1 See Note 1 3.48
.100 .150 or .200 .042
Right-Angle Posts, No Mounting Ears 2.54 3.81 or 5.08 1.07 See Note 2 See Note 3 See Note 3
.128
[3.25] Dia.
C±.003 Dia.
[±0.08]
DB
F
A
.128
[3.25] Dia.
C±.003 Dia.
[±0.08]
D
G
B
F
A
.337
[8.56]
27
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Recommended
PC Board Edge Pattern
PC Board Edge Pattern for
.100 [2.54] and .125 [3.18]
Centerline
.310
[7.87] Min.
C±.005
[±0.13]
D±.005
[±0.13]
B
A
.295
[7.49] Min.
Engagement Depth
.050
[1.27]
Intercontact Key Slot
.054/.070
[1.37/1.77]
.015
[0.38] x 45°
Chamfer
Datum C
L
No. of .100 [2.54] Centerline .125 [3.18] Centerline
Dual A = .093 [2.36] A = .118 [3.00]
Positions B = .050 [1.27] B = .075 [1.90]
C D C D
.386 .200
39.80 5.08
.686 .500 .861 .625
617.42 12.70 21.87 15.88
1.086 .900 1.361 1.125
10 27.58 22.86 34.57 28.58
1.286 1.100
12 32.66 27.94
1.386 1.200
13 35.20 30.48
1.861 1.625
14 47.27 41.28
1.586 1.400
15 40.28 35.56
1.786 1.600
17 45.36 40.64
1.886 1.700 2.361 2.125
18 47.90 43.18 59.97 53.98
2.286 2.100 2.861 2.625
22 58.06 53.34 72.67 66.68
2.586 2.400
25 65.68 60.96
2.886 2.700 3.611 3.375
28 73.30 68.58 91.72 85.73
3.086 2.900 3.861 3.625
30 78.38 73.66 98.07 92.08
3.186 3.000 3.986 3.750
31 80.92 76.20 101.24 95.25
3.586 3.400
35 91.08 86.36
3.686 3.500 4.611 4.375
36 93.62 88.90 117.12 111.13
4.086 3.900 5.111 4.875
40 103.78 99.06 129.82 123.82
4.386 4.200 5.486 5.250
43 111.40 106.68 139.34 133.35
5.086 4.900 6.361 6.125
50 129.18 124.46 161.57 155.58
6.086 5.900
60 154.58 149.86
7.086 6.900
70 179.98 175.26
28
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Card Edge Connectors
Product Facts
Double readout Card Edge
connectors use dip solder
contacts
Large lead-in chamfers
allow easy PC board
installation
Insulator standoffs prevent
solder from wicking
Various lengths for custom
applications
Contact option, single or
dual row
Cantilever Beam
The Cantilever Beam Card
Edge connector comes with
standard high temperature
plastic insulators. Contacts
are available in a variety of
lengths to accommodate
various custom applica-
tions. Standoffs allow for
cleaning and draining and
are available as an option
on most insulator bodies.
Cantilever Beam Card Edge
offers a variety of card slot
depths. A full scoop option
is available for ease of
installation in applications
where visibility is limited.
Contact options vary in this
series from dual row stan-
dard contacts, single row
options and press-fit.
Design Advantages
• Circuit Integrity: Robust
cantilever contacts are
designed to promote
optimal normal forces at
the lowest possible cost.
Our uniquely contoured
contact mating surface
gives you constant
engagement, even when
subjected to continuous
vibration.
• Ease of Assembly:
Generous lead-in cham-
fers let your P.C. board
slide easily into the con-
nector. Insulator standoffs
are provided to facilitate
cleaning and prevent sol-
der from wicking.
Availability, flexibility, per-
formance and very low cost
make the Cantilever Series
from Tyco Electronics the
clear choice in Card Edge
connectors.
Description
The Cantilever Beam Series
products from Tyco
Electronics are double
readout cardedge
connectors, using dip
solder contacts. Tooled for
flexible manufacturing,
these Card Edge
connectors are readily
available in a broad
assortment of sizes and
mounting styles. Our
connectors meet industry
standards.
29
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Ordering Information
Acquired Part Number
C8D52DS29C1M191 – Insulator with molded-in polarizing key with card
guide chamber. The card slot lengths are 1.900 [48.26] and 3.200 [81.28].
Includes retention tails for .062 [1.57] PCB to hold connectors securely during
handling.
C8D52DS29C1M195 – Same as above. No retention tails.
.400
[10.16]
.13
[3.30]
.145
[3.68] .300
[7.62] Card Slot Depth
.200
[5.08]
.100
[2.54]
.040±.003
[1.02±.080] Dia.
.020±.010
[.51±.25] Contact Gap
3.000
[76.20]
1.900
[48.26]
5.100
[129.54]
3.70
[9.40]
.06
[1.52]
.06
[1.52]
.610
[15.49]
.200
[5.08] Ref.
.100
[2.54] Ref.
.100
[2.54] Typ.
3.200
[81.28]
.300
[7.62]
5.300
[134.62]
5.460
[138.68]
1.700
[43.18]
.200
[5.08]
30
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline
Dip Solder Tails, .300 [7.62] Card Slot Depth
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern
page 57
Mounting Styles
.200
[5.08]
.100
[2.54]
.200
[5.08]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.100
[2.54] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
.370
[9.40]
31
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l ABCDEMounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130" [3.30] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 1 C 8 D 0 6 D S 2 9 B 1 C 8 D 0 6 D S 2 9 C 1 C 8 D 0 6 D S 2 9 D 1 C 8 D 0 6 D S 2 9 E 1
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 1 C 8 D 1 0 D S 2 9 B 1 C 8 D 1 0 D S 2 9 C 1 C 8 D 1 0 D S 2 9 D 1 C 8 D 1 0 D S 2 9 E 1
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 1 C 8 D 1 2 D S 2 9 B 1 C 8 D 1 2 D S 2 9 C 1 C 8 D 1 2 D S 2 9 D 1 C 8 D 1 2 D S 2 9 E 1
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 1 C 8 D 1 5 D S 2 9 B 1 C 8 D 1 5 D S 2 9 C 1 C 8 D 1 5 D S 2 9 D 1 C 8 D 1 5 D S 2 9 E 1
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 1 C 8 D 1 8 D S 2 9 B 1 C 8 D 1 8 D S 2 9 C 1 C 8 D 1 8 D S 2 9 D 1 C 8 D 1 8 D S 2 9 E 1
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 1 C 8 D 2 0 D S 2 9 B 1 C 8 D 2 0 D S 2 9 C 1 C 8 D 2 0 D S 2 9 D 1 C 8 D 2 0 D S 2 9 E 1
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 1 C 8 D 2 2 D S 2 9 B 1 C 8 D 2 2 D S 2 9 C 1 C 8 D 2 2 D S 2 9 D 1 C 8 D 2 2 D S 2 9 E 1
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 1 C 8 D 2 5 D S 2 9 B 1 C 8 D 2 5 D S 2 9 C 1 C 8 D 2 5 D S 2 9 D 1 C 8 D 2 5 D S 2 9 E 1
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 1 C 8 D 2 8 D S 2 9 B 1 C 8 D 2 8 D S 2 9 C 1 C 8 D 2 8 D S 2 9 D 1 C 8 D 2 8 D S 2 9 E 1
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 1 C 8 D 3 0 D S 2 9 B 1 C 8 D 3 0 D S 2 9 C 1 C 8 D 3 0 D S 2 9 D 1 C 8 D 3 0 D S 2 9 E 1
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 1 C 8 D 3 1 D S 2 9 B 1 C 8 D 3 1 D S 2 9 C 1 C 8 D 3 1 D S 2 9 D 1 C 8 D 3 1 D S 2 9 E 1
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 1 C 8 D 3 5 D S 2 9 B 1 C 8 D 3 5 D S 2 9 C 1 C 8 D 3 5 D S 2 9 D 1 C 8 D 3 5 D S 2 9 E 1
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 1 C 8 D 3 6 D S 2 9 B 1 C 8 D 3 6 D S 2 9 C 1 C 8 D 3 6 D S 2 9 D 1 C 8 D 3 6 D S 2 9 E 1
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 1 C 8 D 4 0 D S 2 9 B 1 C 8 D 4 0 D S 2 9 C 1 C 8 D 4 0 D S 2 9 D 1 C 8 D 4 0 D S 2 9 E 1
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 1 C 8 D 4 3 D S 2 9 B 1 C 8 D 4 3 D S 2 9 C 1 C 8 D 4 3 D S 2 9 D 1 C 8 D 4 3 D S 2 9 E 1
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 1 C 8 D 5 0 D S 2 9 B 1 C 8 D 5 0 D S 2 9 C 1 C 8 D 5 0 D S 2 9 D 1 C 8 D 5 0 D S 2 9 E 1
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 1 C 8 D 6 0 D S 2 9 B 1 C 8 D 6 0 D S 2 9 C 1 C 8 D 6 0 D S 2 9 D 1 C 8 D 6 0 D S 2 9 E 1
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .160" [4.06] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 2 C 8 D 0 6 D S 2 9 B 2 C 8 D 0 6 D S 2 9 C 2 C 8 D 0 6 D S 2 9 D 2 C 8 D 0 6 D S 2 9 E 2
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 2 C 8 D 1 0 D S 2 9 B 2 C 8 D 1 0 D S 2 9 C 2 C 8 D 1 0 D S 2 9 D 2 C 8 D 1 0 D S 2 9 E 2
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 2 C 8 D 1 2 D S 2 9 B 2 C 8 D 1 2 D S 2 9 C 2 C 8 D 1 2 D S 2 9 D 2 C 8 D 1 2 D S 2 9 E 2
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 2 C 8 D 1 5 D S 2 9 B 2 C 8 D 1 5 D S 2 9 C 2 C 8 D 1 5 D S 2 9 D 2 C 8 D 1 5 D S 2 9 E 2
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 2 C 8 D 1 8 D S 2 9 B 2 C 8 D 1 8 D S 2 9 C 2 C 8 D 1 8 D S 2 9 D 2 C 8 D 1 8 D S 2 9 E 2
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 2 C 8 D 2 0 D S 2 9 B 2 C 8 D 2 0 D S 2 9 C 2 C 8 D 2 0 D S 2 9 D 2 C 8 D 2 0 D S 2 9 E 2
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 2 C 8 D 2 2 D S 2 9 B 2 C 8 D 2 2 D S 2 9 C 2 C 8 D 2 2 D S 2 9 D 2 C 8 D 2 2 D S 2 9 E 2
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 2 C 8 D 2 5 D S 2 9 B 2 C 8 D 2 5 D S 2 9 C 2 C 8 D 2 5 D S 2 9 D 2 C 8 D 2 5 D S 2 9 E 2
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 2 C 8 D 2 8 D S 2 9 B 2 C 8 D 2 8 D S 2 9 C 2 C 8 D 2 8 D S 2 9 D 2 C 8 D 2 8 D S 2 9 E 2
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 2 C 8 D 3 0 D S 2 9 B 2 C 8 D 3 0 D S 2 9 C 2 C 8 D 3 0 D S 2 9 D 2 C 8 D 3 0 D S 2 9 E 2
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 2 C 8 D 3 1 D S 2 9 B 2 C 8 D 3 1 D S 2 9 C 2 C 8 D 3 1 D S 2 9 D 2 C 8 D 3 1 D S 2 9 E 2
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 2 C 8 D 3 5 D S 2 9 B 2 C 8 D 3 5 D S 2 9 C 2 C 8 D 3 5 D S 2 9 D 2 C 8 D 3 5 D S 2 9 E 2
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 2 C 8 D 3 6 D S 2 9 B 2 C 8 D 3 6 D S 2 9 C 2 C 8 D 3 6 D S 2 9 D 2 C 8 D 3 6 D S 2 9 E 2
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 2 C 8 D 4 0 D S 2 9 B 2 C 8 D 4 0 D S 2 9 C 2 C 8 D 4 0 D S 2 9 D 2 C 8 D 4 0 D S 2 9 E 2
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 2 C 8 D 4 3 D S 2 9 B 2 C 8 D 4 3 D S 2 9 C 2 C 8 D 4 3 D S 2 9 D 2 C 8 D 4 3 D S 2 9 E 2
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
32
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”) (Continued)
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 2 C 8 D 5 0 D S 2 9 B 2 C 8 D 5 0 D S 2 9 C 2 C 8 D 5 0 D S 2 9 D 2 C 8 D 5 0 D S 2 9 E 2
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 2 C 8 D 6 0 D S 2 9 B 2 C 8 D 6 0 D S 2 9 C 2 C 8 D 6 0 D S 2 9 D 2 C 8 D 6 0 D S 2 9 E 2
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .220" [5.59] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 3 C 8 D 0 6 D S 2 9 B 3 C 8 D 0 6 D S 2 9 C 3 C 8 D 0 6 D S 2 9 D 3 C 8 D 0 6 D S 2 9 E 3
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 3 C 8 D 1 0 D S 2 9 B 3 C 8 D 1 0 D S 2 9 C 3 C 8 D 1 0 D S 2 9 D 3 C 8 D 1 0 D S 2 9 E 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 3 C 8 D 1 2 D S 2 9 B 3 C 8 D 1 2 D S 2 9 C 3 C 8 D 1 2 D S 2 9 D 3 C 8 D 1 2 D S 2 9 E 3
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 3 C 8 D 1 5 D S 2 9 B 3 C 8 D 1 5 D S 2 9 C 3 C 8 D 1 5 D S 2 9 D 3 C 8 D 1 5 D S 2 9 E 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 3 C 8 D 1 8 D S 2 9 B 3 C 8 D 1 8 D S 2 9 C 3 C 8 D 1 8 D S 2 9 D 3 C 8 D 1 8 D S 2 9 E 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 3 C 8 D 2 0 D S 2 9 B 3 C 8 D 2 0 D S 2 9 C 3 C 8 D 2 0 D S 2 9 D 3 C 8 D 2 0 D S 2 9 E 3
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 3 C 8 D 2 2 D S 2 9 B 3 C 8 D 2 2 D S 2 9 C 3 C 8 D 2 2 D S 2 9 D 3 C 8 D 2 2 D S 2 9 E 3
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 3 C 8 D 2 5 D S 2 9 B 3 C 8 D 2 5 D S 2 9 C 3 C 8 D 2 5 D S 2 9 D 3 C 8 D 2 5 D S 2 9 E 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 3 C 8 D 2 8 D S 2 9 B 3 C 8 D 2 8 D S 2 9 C 3 C 8 D 2 8 D S 2 9 D 3 C 8 D 2 8 D S 2 9 E 3
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 3 C 8 D 3 0 D S 2 9 B 3 C 8 D 3 0 D S 2 9 C 3 C 8 D 3 0 D S 2 9 D 3 C 8 D 3 0 D S 2 9 E 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 3 C 8 D 3 1 D S 2 9 B 3 C 8 D 3 1 D S 2 9 C 3 C 8 D 3 1 D S 2 9 D 3 C 8 D 3 1 D S 2 9 E 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 3 C 8 D 3 5 D S 2 9 B 3 C 8 D 3 5 D S 2 9 C 3 C 8 D 3 5 D S 2 9 D 3 C 8 D 3 5 D S 2 9 E 3
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 3 C 8 D 3 6 D S 2 9 B 3 C 8 D 3 6 D S 2 9 C 3 C 8 D 3 6 D S 2 9 D 3 C 8 D 3 6 D S 2 9 E 3
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 3 C 8 D 4 0 D S 2 9 B 3 C 8 D 4 0 D S 2 9 C 3 C 8 D 4 0 D S 2 9 D 3 C 8 D 4 0 D S 2 9 E 3
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 3 C 8 D 4 3 D S 2 9 B 3 C 8 D 4 3 D S 2 9 C 3 C 8 D 4 3 D S 2 9 D 3 C 8 D 4 3 D S 2 9 E 3
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 3 C 8 D 5 0 D S 2 9 B 3 C 8 D 5 0 D S 2 9 C 3 C 8 D 5 0 D S 2 9 D 3 C 8 D 5 0 D S 2 9 E 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 3 C 8 D 6 0 D S 2 9 B 3 C 8 D 6 0 D S 2 9 C 3 C 8 D 6 0 D S 2 9 D 3 C 8 D 6 0 D S 2 9 E 3
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
33
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors 100 x .200 [2.54 x 5.08], .510 [12.95] and
.395 [10.03] Card Slot Depth, Full Scoop
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data
Daughter Card Edge Pattern
page 57
.180
[4.57]
.054 to .071
Accepts [3.37 to 1.80] Thk. PC Board
.200
[5.08]
.100
[2.54]
.100
[2.54]
.180
[4.57]
.705
[17.91]
.390
[9.91]
Dim C
C
C
B
A
.02
[.51] Contact Gap
Card Slot
Depth
.040±.003
[1.02±.08] Dia.
34
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Full Scoop
No. of Dual D i m e n s i o n s Acquired Part
Readout Pos. ABC N u m b e r
.510" [12.95] Card Slot Depth
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 D S 2 9 0 6 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 D S 2 9 0 6 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 D S 2 9 0 6 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 D S 2 9 0 6 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 D S 2 9 0 6 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 D S 2 9 0 6 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 D S 2 9 0 6 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 D S 2 9 0 6 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 D S 2 9 0 6 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 D S 2 9 0 6 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 D S 2 9 0 6 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 D S 2 9 0 6 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 D S 2 9 0 6 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
.395" [10.03] Card Slot Depth
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 D S 2 9 0 9 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 D S 2 9 0 9 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 D S 2 9 0 9 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 D S 2 9 0 9 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 D S 2 9 0 9 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 D S 2 9 0 9 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 D S 2 9 0 9 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 D S 2 9 0 9 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 D S 2 9 0 9 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 D S 2 9 0 9 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 D S 2 9 0 9 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 D S 2 9 0 9 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 D S 2 9 0 9 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
35
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .125 x .250 [3.18 x 6.35] Centerline, Dip Solder
Tails, .300 [7.62] Card Slot Depth
Mounting Styles
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern
page 57
.250
[6.35]
.370
[9.40]
.125
[3.18]
.250
[6.35]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.100
[2.54] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
36
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130 [3.30] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 1 C 7 D 0 6 D S 2 9 B 1 C 7 D 0 6 D S 2 9 C 1 C 7 D 0 6 D S 2 9 D 1 C 7 D 0 6 D S 2 9 E 1
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 1 C 7 D 1 0 D S 2 9 B 1 C 7 D 1 0 D S 2 9 C 1 C 7 D 1 0 D S 2 9 D 1 C 7 D 1 0 D S 2 9 E 1
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 1 C 7 D 1 5 D S 2 9 B 1 C 7 D 1 5 D S 2 9 C 1 C 7 D 1 5 D S 2 9 D 1 C 7 D 1 5 D S 2 9 E 1
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 1 C 7 D 1 8 D S 2 9 B 1 C 7 D 1 8 D S 2 9 C 1 C 7 D 1 8 D S 2 9 D 1 C 7 D 1 8 D S 2 9 E 1
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 1 C 7 D 2 2 D S 2 9 B 1 C 7 D 2 2 D S 2 9 C 1 C 7 D 2 2 D S 2 9 D 1 C 7 D 2 2 D S 2 9 E 1
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 1 C 7 D 2 5 D S 2 9 B 1 C 7 D 2 5 D S 2 9 C 1 C 7 D 2 5 D S 2 9 D 1 C 7 D 2 5 D S 2 9 E 1
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 1 C 7 D 2 8 D S 2 9 B 1 C 7 D 2 8 D S 2 9 C 1 C 7 D 2 8 D S 2 9 D 1 C 7 D 2 8 D S 2 9 E 1
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 1 C 7 D 3 0 D S 2 9 B 1 C 7 D 3 0 D S 2 9 C 1 C 7 D 3 0 D S 2 9 D 1 C 7 D 3 0 D S 2 9 E 1
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 1 C 7 D 3 1 D S 2 9 B 1 C 7 D 3 1 D S 2 9 C 1 C 7 D 3 1 D S 2 9 D 1 C 7 D 3 1 D S 2 9 E 1
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 1 C 7 D 3 5 D S 2 9 B 1 C 7 D 3 5 D S 2 9 C 1 C 7 D 3 5 D S 2 9 D 1 C 7 D 3 5 D S 2 9 E 1
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 1 C 7 D 3 6 D S 2 9 B 1 C 7 D 3 6 D S 2 9 C 1 C 7 D 3 6 D S 2 9 D 1 C 7 D 3 6 D S 2 9 E 1
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 1 C 7 D 4 0 D S 2 9 B 1 C 7 D 4 0 D S 2 9 C 1 C 7 D 4 0 D S 2 9 D 1 C 7 D 4 0 D S 2 9 E 1
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 1 C 7 D 4 3 D S 2 9 B 1 C 7 D 4 3 D S 2 9 C 1 C 7 D 4 3 D S 2 9 D 1 C 7 D 4 3 D S 2 9 E 1
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 1 C 7 D 5 0 D S 2 9 B 1 C 7 D 5 0 D S 2 9 C 1 C 7 D 5 0 D S 2 9 D 1 C 7 D 5 0 D S 2 9 E 1
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
Tail Length .160 [4.06] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 3 C 7 D 0 6 D S 2 9 B 3 C 7 D 0 6 D S 2 9 C 3 C 7 D 0 6 D S 2 9 D 3 C 7 D 0 6 D S 2 9 E 3
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 3 C 7 D 1 0 D S 2 9 B 3 C 7 D 1 0 D S 2 9 C 3 C 7 D 1 0 D S 2 9 D 3 C 7 D 1 0 D S 2 9 E 3
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 3 C 7 D 1 5 D S 2 9 B 3 C 7 D 1 5 D S 2 9 C 3 C 7 D 1 5 D S 2 9 D 3 C 7 D 1 5 D S 2 9 E 3
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 3 C 7 D 1 8 D S 2 9 B 3 C 7 D 1 8 D S 2 9 C 3 C 7 D 1 8 D S 2 9 D 3 C 7 D 1 8 D S 2 9 E 3
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 3 C 7 D 2 2 D S 2 9 B 3 C 7 D 2 2 D S 2 9 C 3 C 7 D 2 2 D S 2 9 D 3 C 7 D 2 2 D S 2 9 E 3
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 3 C 7 D 2 5 D S 2 9 B 3 C 7 D 2 5 D S 2 9 C 3 C 7 D 2 5 D S 2 9 D 3 C 7 D 2 5 D S 2 9 E 3
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 3 C 7 D 2 8 D S 2 9 B 3 C 7 D 2 8 D S 2 9 C 3 C 7 D 2 8 D S 2 9 D 3 C 7 D 2 8 D S 2 9 E 3
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 3 C 7 D 3 0 D S 2 9 B 3 C 7 D 3 0 D S 2 9 C 3 C 7 D 3 0 D S 2 9 D 3 C 7 D 3 0 D S 2 9 E 3
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 3 C 7 D 3 1 D S 2 9 B 3 C 7 D 3 1 D S 2 9 C 3 C 7 D 3 1 D S 2 9 D 3 C 7 D 3 1 D S 2 9 E 3
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 3 C 7 D 3 5 D S 2 9 B 3 C 7 D 3 5 D S 2 9 C 3 C 7 D 3 5 D S 2 9 D 3 C 7 D 3 5 D S 2 9 E 3
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 3 C 7 D 3 6 D S 2 9 B 3 C 7 D 3 6 D S 2 9 C 3 C 7 D 3 6 D S 2 9 D 3 C 7 D 3 6 D S 2 9 E 3
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 3 C 7 D 4 0 D S 2 9 B 3 C 7 D 4 0 D S 2 9 C 3 C 7 D 4 0 D S 2 9 D 3 C 7 D 4 0 D S 2 9 E 3
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 3 C 7 D 4 3 D S 2 9 B 3 C 7 D 4 3 D S 2 9 C 3 C 7 D 4 3 D S 2 9 D 3 C 7 D 4 3 D S 2 9 E 3
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 3 C 7 D 5 0 D S 2 9 B 3 C 7 D 5 0 D S 2 9 C 3 C 7 D 5 0 D S 2 9 D 3 C 7 D 5 0 D S 2 9 E 3
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
37
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .220 [5.59] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 4 C 7 D 0 6 D S 2 9 B 4 C 7 D 0 6 D S 2 9 C 4 C 7 D 0 6 D S 2 9 D 4 C 7 D 0 6 D S 2 9 E 4
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 4 C 7 D 1 0 D S 2 9 B 4 C 7 D 1 0 D S 2 9 C 4 C 7 D 1 0 D S 2 9 D 4 C 7 D 1 0 D S 2 9 E 4
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 4 C 7 D 1 5 D S 2 9 B 4 C 7 D 1 5 D S 2 9 C 4 C 7 D 1 5 D S 2 9 D 4 C 7 D 1 5 D S 2 9 E 4
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 4 C 7 D 1 8 D S 2 9 B 4 C 7 D 1 8 D S 2 9 C 4 C 7 D 1 8 D S 2 9 D 4 C 7 D 1 8 D S 2 9 E 4
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 4 C 7 D 2 2 D S 2 9 B 4 C 7 D 2 2 D S 2 9 C 4 C 7 D 2 2 D S 2 9 D 4 C 7 D 2 2 D S 2 9 E 4
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 4 C 7 D 2 5 D S 2 9 B 4 C 7 D 2 5 D S 2 9 C 4 C 7 D 2 5 D S 2 9 D 4 C 7 D 2 5 D S 2 9 E 4
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 4 C 7 D 2 8 D S 2 9 B 4 C 7 D 2 8 D S 2 9 C 4 C 7 D 2 8 D S 2 9 D 4 C 7 D 2 8 D S 2 9 E 4
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 4 C 7 D 3 0 D S 2 9 B 4 C 7 D 3 0 D S 2 9 C 4 C 7 D 3 0 D S 2 9 D 4 C 7 D 3 0 D S 2 9 E 4
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 4 C 7 D 3 1 D S 2 9 B 4 C 7 D 3 1 D S 2 9 C 4 C 7 D 3 1 D S 2 9 D 4 C 7 D 3 1 D S 2 9 E 4
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 4 C 7 D 3 5 D S 2 9 B 4 C 7 D 3 5 D S 2 9 C 4 C 7 D 3 5 D S 2 9 D 4 C 7 D 3 5 D S 2 9 E 4
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 4 C 7 D 3 6 D S 2 9 B 4 C 7 D 3 6 D S 2 9 C 4 C 7 D 3 6 D S 2 9 D 4 C 7 D 3 6 D S 2 9 E 4
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 4 C 7 D 4 0 D S 2 9 B 4 C 7 D 4 0 D S 2 9 C 4 C 7 D 4 0 D S 2 9 D 4 C 7 D 4 0 D S 2 9 E 4
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 4 C 7 D 4 3 D S 2 9 B 4 C 7 D 4 3 D S 2 9 C 4 C 7 D 4 3 D S 2 9 D 4 C 7 D 4 3 D S 2 9 E 4
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 4 C 7 D 5 0 D S 2 9 B 4 C 7 D 5 0 D S 2 9 C 4 C 7 D 5 0 D S 2 9 D 4 C 7 D 5 0 D S 2 9 E 4
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
38
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series .156 x .200 [3.96 x 5.08] Centerline, Dip Solder Tails,
.300 [7.62] Card Slot Depth
Mounting Styles
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern
page 57
.200
[5.08]
.156
[3.96]
.200
[5.08]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.156
[3.96] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
.370
[9.40]
39
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130 [3.30] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 1 C 6 D 0 6 D S 2 9 B 1 C 6 D 0 6 D S 2 9 C 1 C 6 D 0 6 D S 2 9 D 1 C 6 D 0 6 D S 2 9 E 1
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 1 C 6 D 1 0 D S 2 9 B 1 C 6 D 1 0 D S 2 9 C 1 C 6 D 1 0 D S 2 9 D 1 C 6 D 1 0 D S 2 9 E 1
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 1 C 6 D 1 2 D S 2 9 B 1 C 6 D 1 2 D S 2 9 C 1 C 6 D 1 2 D S 2 9 D 1 C 6 D 1 2 D S 2 9 E 1
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 1 C 6 D 1 5 D S 2 9 B 1 C 6 D 1 5 D S 2 9 C 1 C 6 D 1 5 D S 2 9 D 1 C 6 D 1 5 D S 2 9 E 1
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 1 C 6 D 1 8 D S 2 9 B 1 C 6 D 1 8 D S 2 9 C 1 C 6 D 1 8 D S 2 9 D 1 C 6 D 1 8 D S 2 9 E 1
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 1 C 6 D 2 0 D S 2 9 B 1 C 6 D 2 0 D S 2 9 C 1 C 6 D 2 0 D S 2 9 D 1 C 6 D 2 0 D S 2 9 E 1
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 1 C 6 D 2 2 D S 2 9 B 1 C 6 D 2 2 D S 2 9 C 1 C 6 D 2 2 D S 2 9 D 1 C 6 D 2 2 D S 2 9 E 1
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 1 C 6 D 2 5 D S 2 9 B 1 C 6 D 2 5 D S 2 9 C 1 C 6 D 2 5 D S 2 9 D 1 C 6 D 2 5 D S 2 9 E 1
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 1 C 6 D 2 8 D S 2 9 B 1 C 6 D 2 8 D S 2 9 C 1 C 6 D 2 8 D S 2 9 D 1 C 6 D 2 8 D S 2 9 E 1
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 1 C 6 D 3 0 D S 2 9 B 1 C 6 D 3 0 D S 2 9 C 1 C 6 D 3 0 D S 2 9 D 1 C 6 D 3 0 D S 2 9 E 1
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 1 C 6 D 3 1 D S 2 9 B 1 C 6 D 3 1 D S 2 9 C 1 C 6 D 3 1 D S 2 9 D 1 C 6 D 3 1 D S 2 9 E 1
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 1 C 6 D 3 5 D S 2 9 B 1 C 6 D 3 5 D S 2 9 C 1 C 6 D 3 5 D S 2 9 D 1 C 6 D 3 5 D S 2 9 E 1
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 1 C 6 D 3 6 D S 2 9 B 1 C 6 D 3 6 D S 2 9 C 1 C 6 D 3 6 D S 2 9 D 1 C 6 D 3 6 D S 2 9 E 1
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 1 C 6 D 4 0 D S 2 9 B 1 C 6 D 4 0 D S 2 9 C 1 C 6 D 4 0 D S 2 9 D 1 C 6 D 4 0 D S 2 9 E 1
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 1 C 6 D 4 3 D S 2 9 B 1 C 6 D 4 3 D S 2 9 C 1 C 6 D 4 3 D S 2 9 D 1 C 6 D 4 3 D S 2 9 E 1
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 1 C 6 D 5 0 D S 2 9 B 1 C 6 D 5 0 D S 2 9 C 1 C 6 D 5 0 D S 2 9 D 1 C 6 D 5 0 D S 2 9 E 1
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
Tail Length .160 [4.06] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 3 C 6 D 0 6 D S 2 9 B 3 C 6 D 0 6 D S 2 9 C 3 C 6 D 0 6 D S 2 9 D 3 C 6 D 0 6 D S 2 9 E 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 3 C 6 D 1 0 D S 2 9 B 3 C 6 D 1 0 D S 2 9 C 3 C 6 D 1 0 D S 2 9 D 3 C 6 D 1 0 D S 2 9 E 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 3 C 6 D 1 2 D S 2 9 B 3 C 6 D 1 2 D S 2 9 C 3 C 6 D 1 2 D S 2 9 D 3 C 6 D 1 2 D S 2 9 E 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 3 C 6 D 1 5 D S 2 9 B 3 C 6 D 1 5 D S 2 9 C 3 C 6 D 1 5 D S 2 9 D 3 C 6 D 1 5 D S 2 9 E 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 3 C 6 D 1 8 D S 2 9 B 3 C 6 D 1 8 D S 2 9 C 3 C 6 D 1 8 D S 2 9 D 3 C 6 D 1 8 D S 2 9 E 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 3 C 6 D 2 0 D S 2 9 B 3 C 6 D 2 0 D S 2 9 C 3 C 6 D 2 0 D S 2 9 D 3 C 6 D 2 0 D S 2 9 E 3
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 3 C 6 D 2 2 D S 2 9 B 3 C 6 D 2 2 D S 2 9 C 3 C 6 D 2 2 D S 2 9 D 3 C 6 D 2 2 D S 2 9 E 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 3 C 6 D 2 5 D S 2 9 B 3 C 6 D 2 5 D S 2 9 C 3 C 6 D 2 5 D S 2 9 D 3 C 6 D 2 5 D S 2 9 E 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 3 C 6 D 2 8 D S 2 9 B 3 C 6 D 2 8 D S 2 9 C 3 C 6 D 2 8 D S 2 9 D 3 C 6 D 2 8 D S 2 9 E 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 3 C 6 D 3 0 D S 2 9 B 3 C 6 D 3 0 D S 2 9 C 3 C 6 D 3 0 D S 2 9 D 3 C 6 D 3 0 D S 2 9 E 3
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 3 C 6 D 3 1 D S 2 9 B 3 C 6 D 3 1 D S 2 9 C 3 C 6 D 3 1 D S 2 9 D 3 C 6 D 3 1 D S 2 9 E 3
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 3 C 6 D 3 5 D S 2 9 B 3 C 6 D 3 5 D S 2 9 C 3 C 6 D 3 5 D S 2 9 D 3 C 6 D 3 5 D S 2 9 E 3
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 3 C 6 D 3 6 D S 2 9 B 3 C 6 D 3 6 D S 2 9 C 3 C 6 D 3 6 D S 2 9 D 3 C 6 D 3 6 D S 2 9 E 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 3 C 6 D 4 0 D S 2 9 B 3 C 6 D 4 0 D S 2 9 C 3 C 6 D 4 0 D S 2 9 D 3 C 6 D 4 0 D S 2 9 E 3
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 3 C 6 D 4 3 D S 2 9 B 3 C 6 D 4 3 D S 2 9 C 3 C 6 D 4 3 D S 2 9 D 3 C 6 D 4 3 D S 2 9 E 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 3 C 6 D 5 0 D S 2 9 B 3 C 6 D 5 0 D S 2 9 C 3 C 6 D 5 0 D S 2 9 D 3 C 6 D 5 0 D S 2 9 E 3
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
40
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s T h r uH o l e i n s e r t Thru Hole i n s e r t
Tail Length .220" [5.59] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 4 C 6 D 0 6 D S 2 9 B 4 C 6 D 0 6 D S 2 9 C 4 C 6 D 0 6 D S 2 9 D 4 C 6 D 0 6 D S 2 9 E 4
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 4 C 6 D 1 0 D S 2 9 B 4 C 6 D 1 0 D S 2 9 C 4 C 6 D 1 0 D S 2 9 D 4 C 6 D 1 0 D S 2 9 E 4
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 4 C 6 D 1 2 D S 2 9 B 4 C 6 D 1 2 D S 2 9 C 4 C 6 D 1 2 D S 2 9 D 4 C 6 D 1 2 D S 2 9 E 4
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 4 C 6 D 1 5 D S 2 9 B 4 C 6 D 1 5 D S 2 9 C 4 C 6 D 1 5 D S 2 9 D 4 C 6 D 1 5 D S 2 9 E 4
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 4 C 6 D 1 8 D S 2 9 B 4 C 6 D 1 8 D S 2 9 C 4 C 6 D 1 8 D S 2 9 D 4 C 6 D 1 8 D S 2 9 E 4
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 4 C 6 D 2 0 D S 2 9 B 4 C 6 D 2 0 D S 2 9 C 4 C 6 D 2 0 D S 2 9 D 4 C 6 D 2 0 D S 2 9 E 4
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 4 C 6 D 2 2 D S 2 9 B 4 C 6 D 2 2 D S 2 9 C 4 C 6 D 2 2 D S 2 9 D 4 C 6 D 2 2 D S 2 9 E 4
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 4 C 6 D 2 5 D S 2 9 B 4 C 6 D 2 5 D S 2 9 C 4 C 6 D 2 5 D S 2 9 D 4 C 6 D 2 5 D S 2 9 E 4
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 4 C 6 D 2 8 D S 2 9 B 4 C 6 D 2 8 D S 2 9 C 4 C 6 D 2 8 D S 2 9 D 4 C 6 D 2 8 D S 2 9 E 4
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 4 C 6 D 3 0 D S 2 9 B 4 C 6 D 3 0 D S 2 9 C 4 C 6 D 3 0 D S 2 9 D 4 C 6 D 3 0 D S 2 9 E 4
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 4 C 6 D 3 1 D S 2 9 B 4 C 6 D 3 1 D S 2 9 C 4 C 6 D 3 1 D S 2 9 D 4 C 6 D 3 1 D S 2 9 E 4
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 4 C 6 D 3 5 D S 2 9 B 4 C 6 D 3 5 D S 2 9 C 4 C 6 D 3 5 D S 2 9 D 4 C 6 D 3 5 D S 2 9 E 4
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 4 C 6 D 3 6 D S 2 9 B 4 C 6 D 3 6 D S 2 9 C 4 C 6 D 3 6 D S 2 9 D 4 C 6 D 3 6 D S 2 9 E 4
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 4 C 6 D 4 0 D S 2 9 B 4 C 6 D 4 0 D S 2 9 C 4 C 6 D 4 0 D S 2 9 D 4 C 6 D 4 0 D S 2 9 E 4
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 4 C 6 D 4 3 D S 2 9 B 4 C 6 D 4 3 D S 2 9 C 4 C 6 D 4 3 D S 2 9 D 4 C 6 D 4 3 D S 2 9 E 4
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 4 C 6 D 5 0 D S 2 9 B 4 C 6 D 5 0 D S 2 9 C 4 C 6 D 5 0 D S 2 9 D 4 C 6 D 5 0 D S 2 9 E 4
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
41
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Card Edge Connectors
Product Facts
Sizes from 6 to 65 dual
positions.
Contact mating surface
optimizes reliability by
concentrating the normal
force in the actual
contact area.
Mounting ear options
accommodate both Panel
and PC Board
attachment.
Solder stand-offs
facilitate cleaning.
Bifurcated contact
design provides
redundant points of
contact to maximize
reliability.
Tail lengths available to
accommodate .062"
[1.57] through .125"
[3.18] thick PCB Boards
and Wire Wrap
termination.
Straight or Right Angle
contact configurations.
Bifurcated contact design provides maximum reliability
Description/Application
The modified bellows card
edge connectors are dual
readout and are designed
for reliable termination to
double sided PCB boards.
Modified Bellows
The modified bellows card
edge connector offers a
variety of tail lengths for sol-
der and wire wrap applica-
tions. Contacts are
available in straight tail or
right angle configurations to
meet your individual pur-
pose. The modified bellows
line of connectors offers a
variety of card slot depths
and has optional high tem-
perature plastic insulators.
42
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors .100 x .200 [2.54 x 5.08], Straight Dip
Solder And Wire Wrap Tails
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.100
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
.250
[6.35]
.610
[15.49]
J
.100
[2.54]
.200
[5.08]
.368
[9.53]
C
E
B
A
D
.300
[7.62] Card Depth
.054 - .071
[1.37 - 1.80] P.C. Board
.200
[5.08]
.025
[.64] Sq
.180
[4.57]
.610
[15.49] Ref.
.100
[2.54] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
Centered Mounting Ear
4-40 Threaded Insert No Mounting Ears
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
Dim E
43
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDE.125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”)
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 D S 2 9 A 2 A 8 D 1 0 D S 2 9 B 2 A 8 D 1 0 D S 2 9 C 2 A 8 D 1 0 D S 2 9 D 2 A 8 D 1 0 D S 2 9 E 2
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 D S 2 9 A 2 A 8 D 1 2 D S 2 9 B 2 A 8 D 1 2 D S 2 9 C 2
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 D S 2 9 A 2 A 8 D 1 5 D S 2 9 B 2 A 8 D 1 5 D S 2 9 C 2 A 8 D 1 5 D S 2 9 D 2 A 8 D 1 5 D S 2 9 E 2
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 D S 2 9 A 2 A 8 D 1 8 D S 2 9 B 2 A 8 D 1 8 D S 2 9 C 2 A 8 D 1 8 D S 2 9 D 2 A 8 D 1 8 D S 2 9 E 2
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 D S 2 9 A 2 A 8 D 2 0 D S 2 9 B 2 A 8 D 2 0 D S 2 9 C 2
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 D S 2 9 A 2 A 8 D 2 2 D S 2 9 B 2 A 8 D 2 2 D S 2 9 C 2
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 D S 2 9 A 2 A 8 D 2 5 D S 2 9 B 2 A 8 D 2 5 D S 2 9 C 2 A 8 D 2 5 D S 2 9 D 2 A 8 D 2 5 D S 2 9 E 2
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 D S 2 9 A 2 A 8 D 2 8 D S 2 9 B 2 A 8 D 2 8 D S 2 9 C 2
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 D S 2 9 A 2 A 8 D 3 0 D S 2 9 B 2 A 8 D 3 0 D S 2 9 C 2 A 8 D 3 0 D S 2 9 D 2 A 8 D 3 0 D S 2 9 E 2
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 D S 2 9 A 2 A 8 D 3 1 D S 2 9 B 2 A 8 D 3 1 D S 2 9 C 2 A 8 D 3 1 D S 2 9 D 2 A 8 D 3 1 D S 2 9 E 2
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 D S 2 9 A 2 A 8 D 3 5 D S 2 9 B 2 A 8 D 3 5 D S 2 9 C 2
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 D S 2 9 A 2 A 8 D 3 6 D S 2 9 B 2 A 8 D 3 6 D S 2 9 C 2
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 D S 2 9 A 2 A 8 D 4 0 D S 2 9 B 2 A 8 D 4 0 D S 2 9 C 2
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 D S 2 9 A 2 A 8 D 4 3 D S 2 9 B 2 A 8 D 4 3 D S 2 9 C 2
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 D S 2 9 A 2 A 8 D 4 4 D S 2 9 B 2 A 8 D 4 4 D S 2 9 C 2
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 D S 2 9 A 2 A 8 D 5 0 D S 2 9 B 2 A 8 D 5 0 D S 2 9 C 2 A 8 D 5 0 D S 2 9 D 2 A 8 D 5 0 D S 2 9 E 2
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 D S 2 9 A 2 A 8 D 6 0 D S 2 9 B 2 A 8 D 6 0 D S 2 9 C 2
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 D S 2 9 A 2 A 8 D 6 5 D S 2 9 B 2 A 8 D 6 5 D S 2 9 C 2 A 8 D 6 5 D S 2 9 D 2 A 8 D 6 5 D S 2 9 E 2
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
Tail Length .220" [5.59] (DIM “J”)
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 D S 2 9 A 3 A 8 D 1 0 D S 2 9 B 3 A 8 D 1 0 D S 2 9 C 3 A 8 D 1 0 D S 2 9 D 3 A 8 D 1 0 D S 2 9 E 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 D S 2 9 A 3 A 8 D 1 2 D S 2 9 B 3 A 8 D 1 2 D S 2 9 C 3
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 D S 2 9 A 3 A 8 D 1 5 D S 2 9 B 3 A 8 D 1 5 D S 2 9 C 3 A 8 D 1 5 D S 2 9 D 3 A 8 D 1 5 D S 2 9 E 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 D S 2 9 A 3 A 8 D 1 8 D S 2 9 B 3 A 8 D 1 8 D S 2 9 C 3 A 8 D 1 8 D S 2 9 D 3 A 8 D 1 8 D S 2 9 E 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 D S 2 9 A 3 A 8 D 2 0 D S 2 9 B 3 A 8 D 2 0 D S 2 9 C 3
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 D S 2 9 A 3 A 8 D 2 2 D S 2 9 B 3 A 8 D 2 2 D S 2 9 C 3
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 D S 2 9 A 3 A 8 D 2 5 D S 2 9 B 3 A 8 D 2 5 D S 2 9 C 3 A 8 D 3 5 D S 2 9 D 3 A 8 D 3 5 D S 2 9 E 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 D S 2 9 A 3 A 8 D 2 8 D S 2 9 B 3 A 8 D 2 8 D S 2 9 C 3
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 D S 2 9 A 3 A 8 D 3 0 D S 2 9 B 3 A 8 D 3 0 D S 2 9 C 3 A 8 D 3 0 D S 2 9 D 3 A 8 D 3 0 D S 2 9 E 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 D S 2 9 A 3 A 8 D 3 1 D S 2 9 B 3 A 8 D 3 1 D S 2 9 C 3 A 8 D 3 1 D S 2 9 D 3 A 8 D 3 1 D S 2 9 E 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 D S 2 9 A 3 A 8 D 3 5 D S 2 9 B 3 A 8 D 3 5 D S 2 9 C 3
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 D S 2 9 A 3 A 8 D 3 6 D S 2 9 B 3 A 8 D 3 6 D S 2 9 C 3
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 D S 2 9 A 3 A 8 D 4 0 D S 2 9 B 3 A 8 D 4 0 D S 2 9 C 3
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 D S 2 9 A 3 A 8 D 4 3 D S 2 9 B 3 A 8 D 4 3 D S 2 9 C 3
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
44
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDE.125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .220" [5.59] (DIM “J”) (Continued)
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 D S 2 9 A 3 A 8 D 4 4 D S 2 9 B 3 A 8 D 4 4 D S 2 9 C 3
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 D S 2 9 A 3 A 8 D 5 0 D S 2 9 B 3 A 8 D 5 0 D S 2 9 C 3 A 8 D 5 0 D S 2 9 D 3 A 8 D 5 0 D S 2 9 E 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 D S 2 9 A 3 A 8 D 6 0 D S 2 9 B 3 A 8 D 6 0 D S 2 9 C 3
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 D S 2 9 A 3 A 8 D 6 5 D S 2 9 B 3 A 8 D 6 5 D S 2 9 C 3 A 8 D 6 5 D S 2 9 D 3 A 8 D 6 5 D S 2 9 E 3
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
Tail Length .560" [14.22] (DIM “J”) for Wire Wrap Termination
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 W W 2 9 A 3 A 8 D 1 0 W W 2 9 B 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 W W 2 9 A 3 A 8 D 1 2 W W 2 9 B 3
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 W W 2 9 A 3 A 8 D 1 5 W W 2 9 B 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 W W 2 9 A 3 A 8 D 1 8 W W 2 9 B 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 W W 2 9 A 3 A 8 D 2 0 W W 2 9 B 3
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 W W 2 9 A 3 A 8 D 2 2 W W 2 9 B 3
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 W W 2 9 A 3 A 8 D 2 5 W W 2 9 B 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 W W 2 9 A 3 A 8 D 2 8 W W 2 9 B 3
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 W W 2 9 A 3 A 8 D 3 0 W W 2 9 B 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 W W 2 9 A 3 A 8 D 3 1 W W 2 9 B 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 W W 2 9 A 3 A 8 D 3 5 W W 2 9 B 3
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 W W 2 9 A 3 A 8 D 3 6 W W 2 9 B 3
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 W W 2 9 A 3 A 8 D 4 0 W W 2 9 B 3
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 W W 2 9 A 3 A 8 D 4 3 W W 2 9 B 3
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 W W 2 9 A 3 A 8 D 4 4 W W 2 9 B 3
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 W W 2 9 A 3 A 8 D 5 0 W W 2 9 B 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 W W 2 9 A 3 A 8 D 6 0 W W 2 9 B 3
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 W W 2 9 A 3 A 8 D 6 5 W W 2 9 B 3
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
45
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors .100 x .200 [2.54 x 5.08] and
.100 x .150 [2.54 x 3.81] Right Angle Dip Solder Tails
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair using
.0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add suffix
M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030 [0.00076]
gold in the mating area, tin/lead on tails,
.000100 [0.00254] minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
Mounting Styles
.100
SECTION X-X
ROTATED 90º
SECTION X-X
.14±.01
[3.56±.25]
.368
[9.35]
H
.025
[.64] Sq. Typ.
.100
[2.54] Ref.
.250
[6.35]
.100
[2.54]
.040±.003
[1.02±.08] Dia.
.054±.071
[1.37±1.890] PC Board
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim G
Dim K
Dim B
A
B
E
D
C
Dim E
Dim H
Row to Row Spacing
.180
[4.57]
.250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
Centered Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears .180
[4.57]
.250
[6.35]
46
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
46
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDEEar Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 0 R A 2 9 A A 8 D 1 0 R A 2 9 C A 8 D 1 0 R A 2 9 E A 8 D 1 0 R A 2 9 F
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6 1 1 . 9 4 7 . 3 7
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 2 R A 2 9 A A 8 D 1 2 R A 2 9 C A 8 D 1 2 R A 2 9 E
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4 1 1 . 9 4 7 . 3 7
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 5 R A 2 9 A A 8 D 1 5 R A 2 9 C A 8 D 1 5 R A 2 9 E A 8 D 1 5 R A 2 9 F
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6 1 1 . 9 4 7 . 3 7
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 8 R A 2 9 A A 8 D 1 8 R A 2 9 C A 8 D 1 8 R A 2 9 E A 8 D 1 8 R A 2 9 F
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8 1 1 . 9 4 7 . 3 7
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 0 R A 2 9 A A 8 D 2 0 R A 2 9 C A 8 D 2 0 R A 2 9 E
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6 1 1 . 9 4 7 . 3 7
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 2 R A 2 9 A A 8 D 2 2 R A 2 9 C A 8 D 2 2 R A 2 9 E
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4 1 1 . 9 4 7 . 3 7
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 5 R A 2 9 A A 8 D 2 5 R A 2 9 C A 8 D 2 5 R A 2 9 E A 8 D 2 5 R A 2 9 F
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6 1 1 . 9 4 7 . 3 7
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 8 R A 2 9 A A 8 D 2 8 R A 2 9 C A 8 D 2 8 R A 2 9 E
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8 1 1 . 9 4 7 . 3 7
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 0 R A 2 9 A A 8 D 3 0 R A 2 9 C A 8 D 3 0 R A 2 9 E A 8 D 3 0 R A 2 9 F
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6 1 1 . 9 4 7 . 3 7
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 1 R A 2 9 A A 8 D 3 1 R A 2 9 C A 8 D 3 1 R A 2 9 E A 8 D 3 1 R A 2 9 F
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4 1 1 . 9 4 7 . 3 7
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 5 R A 2 9 A A 8 D 3 5 R A 2 9 C A 8 D 3 5 R A 2 9 E
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6 1 1 . 9 4 7 . 3 7
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 6 R A 2 9 A A 8 D 3 6 R A 2 9 C A 8 D 3 6 R A 2 9 E
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0 1 1 . 9 4 7 . 3 7
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 0 R A 2 9 A A 8 D 4 0 R A 2 9 C A 8 D 4 0 R A 2 9 E
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6 1 1 . 9 4 7 . 3 7
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 3 R A 2 9 A A 8 D 4 3 R A 2 9 C A 8 D 4 3 R A 2 9 E
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8 1 1 . 9 4 7 . 3 7
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 4 R A 2 9 A A 8 D 4 4 R A 2 9 C A 8 D 4 4 R A 2 9 E
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2 1 1 . 9 4 7 . 3 7
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 5 0 R A 2 9 A A 8 D 5 0 R A 2 9 C A 8 D 5 0 R A 2 9 E A 8 D 5 0 R A 2 9 F
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2 1 1 . 9 4 7 . 3 7
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 6 0 R A 2 9 A A 8 D 6 0 R A 2 9 C A 8 D 6 0 R A 2 9 E
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6 1 1 . 9 4 7 . 3 7
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 6 5 R A 2 9 A A 8 D 6 5 R A 2 9 C A 8 D 6 5 R A 2 9 E A 8 D 6 5 R A 2 9 F
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6 1 1 . 9 4 7 . 3 7
47
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDEEar Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 0 R A 2 9 A M 2 3 3 A 8 D 1 0 R A 2 9 C M 2 3 3 A 8 D 1 0 R A 2 9 E M 2 3 3 A 8 D 1 0 R A 2 9 F M 2 3 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6 1 0 . 6 7 6 . 1 0
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 2 R A 2 9 A M 2 3 3 A 8 D 1 2 R A 2 9 C M 2 3 3 A 8 D 1 2 R A 2 9 E M 2 3 3
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4 1 0 . 6 7 6 . 1 0
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 5 R A 2 9 A M 2 3 3 A 8 D 1 5 R A 2 9 C M 2 3 3 A 8 D 1 5 R A 2 9 E M 2 3 3 A 8 D 1 5 R A 2 9 F M 2 3 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6 1 0 . 6 7 6 . 1 0
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 8 R A 2 9 A M 2 3 3 A 8 D 1 8 R A 2 9 C M 2 3 3 A 8 D 1 8 R A 2 9 E M 2 3 3 A 8 D 1 8 R A 2 9 F M 2 3 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8 1 0 . 6 7 6 . 1 0
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 0 R A 2 9 A M 2 3 3 A 8 D 2 0 R A 2 9 C M 2 3 3 A 8 D 2 0 R A 2 9 E M 2 3 3
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6 1 0 . 6 7 6 . 1 0
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 2 R A 2 9 A M 2 3 3 A 8 D 2 2 R A 2 9 C M 2 3 3 A 8 D 2 2 R A 2 9 E M 2 3 3
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4 1 0 . 6 7 6 . 1 0
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 5 R A 2 9 A M 2 3 3 A 8 D 2 5 R A 2 9 C M 2 3 3 A 8 D 2 5 R A 2 9 E M 2 3 3 A 8 D 2 5 R A 2 9 F M 2 3 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6 1 0 . 6 7 6 . 1 0
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 8 R A 2 9 A M 2 3 3 A 8 D 2 8 R A 2 9 C M 2 3 3 A 8 D 2 8 R A 2 9 E M 2 3 3
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8 1 0 . 6 7 6 . 1 0
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 0 R A 2 9 A M 2 3 3 A 8 D 3 0 R A 2 9 C M 2 3 3 A 8 D 3 0 R A 2 9 E M 2 3 3 A 8 D 3 0 R A 2 9 F M 2 3 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6 1 0 . 6 7 6 . 1 0
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 1 R A 2 9 A M 2 3 3 A 8 D 3 1 R A 2 9 C M 2 3 3 A 8 D 3 1 R A 2 9 E M 2 3 3 A 8 D 3 1 R A 2 9 F M 2 3 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4 1 0 . 6 7 6 . 1 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 5 R A 2 9 A M 2 3 3 A 8 D 3 5 R A 2 9 C M 2 3 3 A 8 D 3 5 R A 2 9 E M 2 3 3
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6 1 0 . 6 7 6 . 1 0
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 6 R A 2 9 A M 2 3 3 A 8 D 3 6 R A 2 9 C M 2 3 3 A 8 D 3 6 R A 2 9 E M 2 3 3
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0 1 0 . 6 7 6 . 1 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 0 R A 2 9 A M 2 3 3 A 8 D 4 0 R A 2 9 C M 2 3 3 A 8 D 4 0 R A 2 9 E M 2 3 3
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6 1 0 . 6 7 6 . 1 0
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 3 R A 2 9 A M 2 3 3 A 8 D 4 3 R A 2 9 C M 2 3 3 A 8 D 4 3 R A 2 9 E M 2 3 3
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8 1 0 . 6 7 6 . 1 0
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 4 R A 2 9 A M 2 3 3 A 8 D 4 4 R A 2 9 C M 2 3 3 A 8 D 4 4 R A 2 9 E M 2 3 3
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2 1 0 . 6 7 6 . 1 0
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 5 0 R A 2 9 A M 2 3 3 A 8 D 5 0 R A 2 9 C M 2 3 3 A 8 D 5 0 R A 2 9 E M 2 3 3 A 8 D 5 0 R A 2 9 F M 2 3 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2 1 0 . 6 7 6 . 1 0
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 6 0 R A 2 9 A M 2 3 3 A 8 D 6 0 R A 2 9 C M 2 3 3 A 8 D 6 0 R A 2 9 E M 2 3 3
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6 1 0 . 6 7 6 . 1 0
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 6 5 R A 2 9 A M 2 3 3 A 8 D 6 5 R A 2 9 C M 2 3 3 A 8 D 6 5 R A 2 9 E M 2 3 3 A 8 D 6 5 R A 2 9 F M 2 3 3
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6 1 0 . 6 7 6 . 1 0
48
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
48
Modified Bellows Connectors .125 x .250 [3.18 x 6.35], Centerline Straight
Dip Solder and Wire Wrap Ta i l s
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.610
[5.49]
.250
[6.35]
.368
[9.35]
.025
[.64] Sq.
.125
[3.18] Ref.
.250
[6.35]
.125
[3.18]
.250
[6.35]
P±.003
[±.080] Dia.
.054±.071
[1.37±1.890] PC Board
.300
[7.62] Card Depth
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
A
B
E
D
C
J
Dim E
.180
[4.57]
.250
[6.35]
.610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
49
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Dip Solder Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 A 7 D 0 6 D S 2 9 A 2 A 7 D 0 6 D S 2 9 B 2 A 7 D 0 6 D S 2 9 C 2 A 7 D 0 6 D S 2 9 D 2 A 7 D 0 6 D S 2 9 E 2
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 A 7 D 1 0 D S 2 9 A 2 A 7 D 1 0 D S 2 9 B 2 A 7 D 1 0 D S 2 9 C 2 A 7 D 1 0 D S 2 9 D 2 A 7 D 1 0 D S 2 9 E 2
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 A 7 D 1 5 D S 2 9 A 2 A 7 D 1 5 D S 2 9 B 2 A 7 D 1 5 D S 2 9 C 2 A 7 D 1 5 D S 2 9 D 2 A 7 D 1 5 D S 2 9 E 2
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 A 7 D 1 8 D S 2 9 A 2 A 7 D 1 8 D S 2 9 B 2 A 7 D 1 8 D S 2 9 C 2 A 7 D 1 8 D S 2 9 D 2 A 7 D 1 8 D S 2 9 E 2
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 A 7 D 2 2 D S 2 9 A 2 A 7 D 2 2 D S 2 9 B 2 A 7 D 2 2 D S 2 9 C 2
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 A 7 D 2 5 D S 2 9 A 2 A 7 D 2 5 D S 2 9 B 2 A 7 D 2 5 D S 2 9 C 2 A 7 D 2 5 D S 2 9 D 2 A 7 D 2 5 D S 2 9 E 2
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 A 7 D 2 8 D S 2 9 A 2 A 7 D 2 8 D S 2 9 B 2 A 7 D 2 8 D S 2 9 C 2
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 A 7 D 3 0 D S 2 9 A 2 A 7 D 3 0 D S 2 9 B 2 A 7 D 3 0 D S 2 9 C 2 A 7 D 3 0 D S 2 9 D 2 A 7 D 3 0 D S 2 9 E 2
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 A 7 D 3 5 D S 2 9 A 2 A 7 D 3 5 D S 2 9 B 2 A 7 D 3 5 D S 2 9 C 2
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 A 7 D 3 6 D S 2 9 A 2 A 7 D 3 6 D S 2 9 B 2 A 7 D 3 6 D S 2 9 C 2
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 A 7 D 4 0 D S 2 9 A 2 A 7 D 4 0 D S 2 9 B 2 A 7 D 4 0 D S 2 9 C 2
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 A 7 D 4 3 D S 2 9 A 2 A 7 D 4 3 D S 2 9 B 2 A 7 D 4 3 D S 2 9 C 2
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 A 7 D 5 0 D S 2 9 A 2 A 7 D 5 0 D S 2 9 B 2 A 7 D 5 0 D S 2 9 C 2 A 7 D 5 0 D S 2 9 D 2 A 7 D 5 0 D S 2 9 E 2
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Wire Wrap Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .560" [14.22] (DIM “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 A 7 D 0 6 W W 2 9 A 3 A 7 D 0 6 W W 2 9 B 3
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 A 7 D 1 0 W W 2 9 A 3 A 7 D 1 0 W W 2 9 B 3
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 A 7 D 1 5 W W 2 9 A 3 A 7 D 1 5 W W 2 9 B 3
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 A 7 D 1 8 W W 2 9 A 3 A 7 D 1 8 W W 2 9 B 3
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 A 7 D 2 2 W W 2 9 A 3 A 7 D 2 2 W W 2 9 B 3
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 A 7 D 2 5 W W 2 9 A 3 A 7 D 2 5 W W 2 9 B 3
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 A 7 D 2 8 W W 2 9 A 3 A 7 D 2 8 W W 2 9 B 3
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 A 7 D 3 0 W W 2 9 A 3 A 7 D 3 0 W W 2 9 B 3
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 A 7 D 3 5 W W 2 9 A 3 A 7 D 3 5 W W 2 9 B 3
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 A 7 D 3 6 W W 2 9 A 3 A 7 D 3 6 W W 2 9 B 3
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 A 7 D 4 0 W W 2 9 A 3 A 7 D 4 0 W W 2 9 B 3
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 A 7 D 4 3 W W 2 9 A 3 A 7 D 4 3 W W 2 9 B 3
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 A 7 D 5 0 W W 2 9 A 3 A 7 D 5 0 W W 2 9 B 3
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
50
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
50
Modified Bellows Connectors .125 x .250 [3.18 x 6.35], .125 x .150 [3.18 x 3.81],
.125 x .200 [3.18 x 5.08] Centerline, Right Angle Ta i l s
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
.125
[3.18] REF
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.180
[4.57]
.250
[6.35] .250
[6.35]
.250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears .180
[4.57]
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
.14±.01
[3.56±.25]
H
C
D
E
B
A
.025
[.64] Sq. Typ.
.054±.071
[1.37±1.890] PC Board
.125
[3.18]
.368
[9.35]
.040±.003
[1.02±.08] Dia.
Dim G
Dim K
Dim B
Dim E
Dim H
Row to Row Spacing
.128
[3.25] Dia.
51
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.150" [3.81] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 0 6 R A 2 9 A M 2 3 1 A 7 D 0 6 R A 2 9 C M 2 3 1 A 7 D 0 6 R A 2 9 E M 2 3 1 A 7 D 0 6 R A 2 9 F M 2 3 1
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 0 . 6 7 6 . 1 0
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 1 0 R A 2 9 A M 2 3 1 A 7 D 1 0 R A 2 9 C M 2 3 1 A 7 D 1 0 R A 2 9 E M 2 3 1 A 7 D 1 0 R A 2 9 F M 2 3 1
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 0 . 6 7 6 . 1 0
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 1 5 R A 2 9 A M 2 3 1 A 7 D 1 5 R A 2 9 C M 2 3 1 A 7 D 1 5 R A 2 9 E M 2 3 1 A 7 D 1 5 R A 2 9 F M 2 3 1
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 0 . 6 7 6 . 1 0
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 1 8 R A 2 9 A M 2 3 1 A 7 D 1 8 R A 2 9 C M 2 3 1 A 7 D 1 8 R A 2 9 E M 2 3 1 A 7 D 1 8 R A 2 9 F M 2 3 1
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 0 . 6 7 6 . 1 0
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 2 2 R A 2 9 A M 2 3 1 A 7 D 2 2 R A 2 9 C M 2 3 1 A 7 D 2 2 R A 2 9 E M 2 3 1 A 7 D 2 2 R A 2 9 F M 2 3 1
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 0 . 6 7 6 . 1 0
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 4 2 0 0 . 2 4 0
A 7 D 2 5 R A 2 9 A M 2 3 1 A 7 D 2 5 R A 2 9 C M 2 3 1 A 7 D 2 5 R A 2 9 E M 2 3 1 A 7 D 2 5 R A 2 9 F M 2 3 1
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 0 . 6 7 6 . 1 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 2 8 R A 2 9 A M 2 3 1 A 7 D 2 8 R A 2 9 C M 2 3 1 A 7 D 2 8 R A 2 9 E M 2 3 1 A 7 D 2 8 R A 2 9 F M 2 3 1
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 0 . 6 7 6 . 1 0
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 3 0 R A 2 9 A M 2 3 1 A 7 D 3 0 R A 2 9 C M 2 3 1 A 7 D 3 0 R A 2 9 E M 2 3 1 A 7 D 3 0 R A 2 9 F M 2 3 1
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 0 . 6 7 6 . 1 0
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 3 5 R A 2 9 A M 2 3 1 A 7 D 3 5 R A 2 9 C M 2 3 1 A 7 D 3 5 R A 2 9 E M 2 3 1 A 7 D 3 5 R A 2 9 F M 2 3 1
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 0 . 6 7 6 . 1 0
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 3 6 R A 2 9 A M 2 3 1 A 7 D 3 6 R A 2 9 C M 2 3 1 A 7 D 3 6 R A 2 9 E M 2 3 1 A 7 D 3 6 R A 2 9 F M 2 3 1
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 0 . 6 7 6 . 1 0
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 4 0 R A 2 9 A M 2 3 1 A 7 D 4 0 R A 2 9 C M 2 3 1 A 7 D 4 0 R A 2 9 E M 2 3 1 A 7 D 4 0 R A 2 9 F M 2 3 1
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 0 . 6 7 6 . 1 0
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 4 3 R A 2 9 A M 2 3 1 A 7 D 4 3 R A 2 9 C M 2 3 1 A 7 D 4 3 R A 2 9 E M 2 3 1 A 7 D 4 3 R A 2 9 F M 2 3 1
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 0 . 6 7 6 . 1 0
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 5 0 R A 2 9 A M 2 3 1 A 7 D 5 0 R A 2 9 C M 2 3 1 A 7 D 5 0 R A 2 9 E M 2 3 1 A 7 D 5 0 R A 2 9 F M 2 3 1
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 0 . 6 7 6 . 1 0
.200" [5.08] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 0 6 R A 2 9 A M 2 3 2 A 7 D 0 6 R A 2 9 C M 2 3 2 A 7 D 0 6 R A 2 9 E M 2 3 2 A 7 D 0 6 R A 2 9 F M 2 3 2
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 1 . 9 4 7 . 3 7
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 1 0 R A 2 9 A M 2 3 2 A 7 D 1 0 R A 2 9 C M 2 3 2 A 7 D 1 0 R A 2 9 E M 2 3 2 A 7 D 1 0 R A 2 9 F M 2 3 2
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 1 . 9 4 7 . 3 7
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 1 5 R A 2 9 A M 2 3 2 A 7 D 1 5 R A 2 9 C M 2 3 2 A 7 D 1 5 R A 2 9 E M 2 3 2 A 7 D 1 5 R A 2 9 F M 2 3 2
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 1 . 9 4 7 . 3 7
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 1 8 R A 2 9 A M 2 3 2 A 7 D 1 8 R A 2 9 C M 2 3 2 A 7 D 1 8 R A 2 9 E M 2 3 2 A 7 D 1 8 R A 2 9 F M 2 3 2
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 1 . 9 4 7 . 3 7
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 2 2 R A 2 9 A M 2 3 2 A 7 D 2 2 R A 2 9 C M 2 3 2 A 7 D 2 2 R A 2 9 E M 2 3 2 A 7 D 2 2 R A 2 9 F M 2 3 2
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 1 . 9 4 7 . 3 7
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 4 7 0 0 . 2 9 0
A 7 D 2 5 R A 2 9 A M 2 3 2 A 7 D 2 5 R A 2 9 C M 2 3 2 A 7 D 2 5 R A 2 9 E M 2 3 2 A 7 D 2 5 R A 2 9 F M 2 3 2
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 1 . 9 4 7 . 3 7
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 2 8 R A 2 9 A M 2 3 2 A 7 D 2 8 R A 2 9 C M 2 3 2 A 7 D 2 8 R A 2 9 E M 2 3 2 A 7 D 2 8 R A 2 9 F M 2 3 2
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 1 . 9 4 7 . 3 7
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 3 0 R A 2 9 A M 2 3 2 A 7 D 3 0 R A 2 9 C M 2 3 2 A 7 D 3 0 R A 2 9 E M 2 3 2 A 7 D 3 0 R A 2 9 F M 2 3 2
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 1 . 9 4 7 . 3 7
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 3 5 R A 2 9 A M 2 3 2 A 7 D 3 5 R A 2 9 C M 2 3 2 A 7 D 3 5 R A 2 9 E M 2 3 2 A 7 D 3 5 R A 2 9 F M 2 3 2
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 1 . 9 4 7 . 3 7
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 3 6 R A 2 9 A M 2 3 2 A 7 D 3 6 R A 2 9 C M 2 3 2 A 7 D 3 6 R A 2 9 E M 2 3 2 A 7 D 3 6 R A 2 9 F M 2 3 2
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 1 . 9 4 7 . 3 7
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 4 0 R A 2 9 A M 2 3 2 A 7 D 4 0 R A 2 9 C M 2 3 2 A 7 D 4 0 R A 2 9 E M 2 3 2 A 7 D 4 0 R A 2 9 F M 2 3 2
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 1 . 9 4 7 . 3 7
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 4 3 R A 2 9 A M 2 3 2 A 7 D 4 3 R A 2 9 C M 2 3 2 A 7 D 4 3 R A 2 9 E M 2 3 2 A 7 D 4 3 R A 2 9 F M 2 3 2
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 1 . 9 4 7 . 3 7
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 5 0 R A 2 9 A M 2 3 2 A 7 D 5 0 R A 2 9 C M 2 3 2 A 7 D 5 0 R A 2 9 E M 2 3 2 A 7 D 5 0 R A 2 9 F M 2 3 2
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 1 . 9 4 7 . 3 7
52
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
52
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.250" [6.35] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 0 6 R A 2 9 A A 7 D 0 6 R A 2 9 C A 7 D 0 6 R A 2 9 E A 7 D 0 6 R A 2 9 F
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 3 . 2 1 8 . 6 4
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 1 0 R A 2 9 A A 7 D 1 0 R A 2 9 C A 7 D 1 0 R A 2 9 E A 7 D 1 0 R A 2 9 F
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 3 . 2 1 8 . 6 4
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 1 5 R A 2 9 A A 7 D 1 5 R A 2 9 C A 7 D 1 5 R A 2 9 E A 7 D 1 5 R A 2 9 F
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 3 . 2 1 8 . 6 4
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 1 8 R A 2 9 A A 7 D 1 8 R A 2 9 C A 7 D 1 8 R A 2 9 E A 7 D 1 8 R A 2 9 F
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 3 . 2 1 8 . 6 4
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 2 2 R A 2 9 A A 7 D 2 2 R A 2 9 C A 7 D 2 2 R A 2 9 E A 7 D 2 2 R A 2 9 F
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 3 . 2 1 8 . 6 4
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 5 2 0 0 . 3 4 0 A 7 D 2 5 R A 2 9 A A 7 D 2 5 R A 2 9 C A 7 D 2 5 R A 2 9 E A 7 D 2 5 R A 2 9 F
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 3 . 2 1 8 . 6 4
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 2 8 R A 2 9 A A 7 D 2 8 R A 2 9 C A 7 D 2 8 R A 2 9 E A 7 D 2 8 R A 2 9 F
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 3 . 2 1 8 . 6 4
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 3 0 R A 2 9 A A 7 D 3 0 R A 2 9 C A 7 D 3 0 R A 2 9 E A 7 D 3 0 R A 2 9 F
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 3 . 2 1 8 . 6 4
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 3 5 R A 2 9 A A 7 D 3 5 R A 2 9 C A 7 D 3 5 R A 2 9 E A 7 D 3 5 R A 2 9 F
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 3 . 2 1 8 . 6 4
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 3 6 R A 2 9 A A 7 D 3 6 R A 2 9 C A 7 D 3 6 R A 2 9 E A 7 D 3 6 R A 2 9 F
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 3 . 2 1 8 . 6 4
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 4 0 R A 2 9 A A 7 D 4 0 R A 2 9 C A 7 D 4 0 R A 2 9 E A 7 D 4 0 R A 2 9 F
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 3 . 2 1 8 . 6 4
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 4 3 R A 2 9 A A 7 D 4 3 R A 2 9 C A 7 D 4 3 R A 2 9 E A 7 D 4 3 R A 2 9 F
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 3 . 2 1 8 . 6 4
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 5 0 R A 2 9 A A 7 D 5 0 R A 2 9 C A 7 D 5 0 R A 2 9 E A 7 D 5 0 R A 2 9 F
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 3 . 2 1 8 . 6 4
53
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors, .156 x .200 [3.96 x 5.08] Centerline, Straight
Dip Solder and Wire Wrap Ta i l s
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.610
[5.49]
.200
[5.08]
.368
[9.35]
.025
[.64] Sq.
.156
[3.96] Ref.
.250
[6.35]
.156
[3.25]
.200
[5.08]
P±.003 [.08] Dia.
.054±.071
[1.37±1.890 ] PC Board
.300
[7.62] Card Depth
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
A
B
E
D
J
C
Dim E
.180
[4.57]
.610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert No Mounting Ears
54
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
54
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o
D u a l Mounting Ear Mounting Ear M o u n t i n g
R e a d o u t ABCDE .125" [3.18] Thru 4-40 Threaded E a r s
P o s i t i o n s H o l e I n s e r t
Tail Length .160" [4.06] (DIM “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 D S 2 9 A 2 A 6 D 0 6 D S 2 9 B 2 A 6 D 0 6 D S 2 9 C 2
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 D S 2 9 A 2 A 6 D 1 0 D S 2 9 B 2 A 6 D 1 0 D S 2 9 C 2
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 D S 2 9 A 2 A 6 D 1 2 D S 2 9 B 2 A 6 D 1 2 D S 2 9 C 2
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 D S 2 9 A 2 A 6 D 1 5 D S 2 9 B 2 A 6 D 1 5 D S 2 9 C 2
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 D S 2 9 A 2 A 6 D 1 8 D S 2 9 B 2 A 6 D 1 8 D S 2 9 C 2
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 D S 2 9 A 2 A 6 D 2 2 D S 2 9 B 2 A 6 D 2 2 D S 2 9 C 2
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 D S 2 9 A 2 A 6 D 2 5 D S 2 9 B 2 A 6 D 2 5 D S 2 9 C 2
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 D S 2 9 A 2 A 6 D 2 8 D S 2 9 B 2 A 6 D 2 8 D S 2 9 C 2
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 D S 2 9 A 2 A 6 D 3 6 D S 2 9 B 2 A 6 D 3 6 D S 2 9 C 2
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 D S 2 9 A 2 A 6 D 4 3 D S 2 9 B 2 A 6 D 4 3 D S 2 9 C 2
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
Tail Length .220" [5.59] (DIM “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 D S 2 9 A 3 A 6 D 0 6 D S 2 9 B 3 A 6 D 0 6 D S 2 9 C 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 D S 2 9 A 3 A 6 D 1 0 D S 2 9 B 3 A 6 D 1 0 D S 2 9 C 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 D S 2 9 A 3 A 6 D 1 2 D S 2 9 B 3 A 6 D 1 2 D S 2 9 C 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 D S 2 9 A 3 A 6 D 1 5 D S 2 9 B 3 A 6 D 1 5 D S 2 9 C 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 D S 2 9 A 3 A 6 D 1 8 D S 2 9 B 3 A 6 D 1 8 D S 2 9 C 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 D S 2 9 A 3 A 6 D 2 2 D S 2 9 B 3 A 6 D 2 2 D S 2 9 C 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 D S 2 9 A 3 A 6 D 2 5 D S 2 9 B 3 A 6 D 2 5 D S 2 9 C 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 D S 2 9 A 3 A 6 D 2 8 D S 2 9 B 3 A 6 D 2 8 D S 2 9 C 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 D S 2 9 A 3 A 6 D 3 6 D S 2 9 B 3 A 6 D 3 6 D S 2 9 C 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 D S 2 9 A 3 A 6 D 4 3 D S 2 9 B 3 A 6 D 4 3 D S 2 9 C 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
Tail Length .560" [14.22] (DIM “J”) For Wire Wrap Termination
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 W W 2 9 A 3 A 6 D 0 6 W W 2 9 B 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 W W 2 9 A 3 A 6 D 1 0 W W 2 9 B 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 W W 2 9 A 3 A 6 D 1 2 W W 2 9 B 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 W W 2 9 A 3 A 6 D 1 5 W W 2 9 B 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 W W 2 9 A 3 A 6 D 1 8 W W 2 9 B 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 W W 2 9 A 3 A 6 D 2 2 W W 2 9 B 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 W W 2 9 A 3 A 6 D 2 5 W W 2 9 B 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 W W 2 9 A 3 A 6 D 2 8 W W 2 9 B 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 W W 2 9 A 3 A 6 D 3 6 W W 2 9 B 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 W W 2 9 A 3 A 6 D 4 3 W W 2 9 B 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
55
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC (sea
level)
Current Rating—3 Amperes
Initial Contact Resistance—10
milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
Modified Bellows Connectors .156 x .200 [3.96 x 5.08] Centerline, .156 x .150
[3.96 x 3.81], Right Angle, Dip Solder Ta i l s
.156
[3.96] REF
SECTION X-X
.180
[4.57]
.250
[6.35] .250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
.14±.01
[3.56±.25]
H
C
D
E
B
A
.025
[.64] Sq. Typ.
.156
[3.96]
.368
[9.35]
.040±.003
[1.02±.08] Dia.
Dim G
Dim K
Dim B
Dim E
Dim H
Row to Row Spacing
.128
[3.25] Dia.
.054±.071
[1.37±1.890] PC Board
56
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
56
Ordering Information
.156" [3.96] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.200" [5.08] Row-to-Row (Dim. “H”) Spacing
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 0 . 4 7 0 0 . 2 9 0 A 6 D 0 6 R A 2 9 A A 6 D 0 6 R A 2 9 C A 6 D 0 6 R A 2 9 E A 6 D 0 6 R A 2 9 F
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1 1 1 . 9 4 7 . 3 7
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 0 . 4 7 0 0 . 2 9 0 A 6 D 1 0 R A 2 9 A A 6 D 1 0 R A 2 9 C A 6 D 1 0 R A 2 9 E A 6 D 1 0 R A 2 9 F
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6 1 1 . 9 4 7 . 3 7
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 0 . 4 7 0 0 . 2 9 0 A 6 D 1 2 R A 2 9 A A 6 D 1 2 R A 2 9 C A 6 D 1 2 R A 2 9 E A 6 D 1 2 R A 2 9 F
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9 1 1 . 9 4 7 . 3 7
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 0 . 4 7 0 0 . 2 9 0 A 6 D 1 5 R A 2 9 A A 6 D 1 5 R A 2 9 C A 6 D 1 5 R A 2 9 E A 6 D 1 5 R A 2 9 F
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7 1 1 . 9 4 7 . 3 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 0 . 4 7 0 0 . 2 9 0 A 6 D 1 8 R A 2 9 A A 6 D 1 8 R A 2 9 C A 6 D 1 8 R A 2 9 E A 6 D 1 8 R A 2 9 F
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6 1 1 . 9 4 7 . 3 7
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 0 . 4 7 0 0 . 2 9 0 A 6 D 2 2 R A 2 9 A A 6 D 2 2 R A 2 9 C A 6 D 2 2 R A 2 9 E A 6 D 2 2 R A 2 9 F
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1 1 1 . 9 4 7 . 3 7
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 0 . 4 7 0 0 . 2 9 0 A 6 D 2 5 R A 2 9 A A 6 D 2 5 R A 2 9 C A 6 D 2 5 R A 2 9 E A 6 D 2 5 R A 2 9 F
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0 1 1 . 9 4 7 . 3 7
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 0 . 4 7 0 0 . 2 9 0 A 6 D 2 8 R A 2 9 A A 6 D 2 8 R A 2 9 C A 6 D 2 8 R A 2 9 E A 6 D 2 8 R A 2 9 F
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8 1 1 . 9 4 7 . 3 7
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 0 . 4 7 0 0 . 2 9 0 A 6 D 3 6 R A 2 9 A A 6 D 3 6 R A 2 9 C A 6 D 3 6 R A 2 9 E A 6 D 3 6 R A 2 9 F
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8 1 1 . 9 4 7 . 3 7
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 4 0 . 4 7 0 0 . 2 9 0 A 6 D 4 0 R A 2 9 A A 6 D 4 0 R A 2 9 C A 6 D 4 0 R A 2 9 E A 6 D 4 0 R A 2 9 F
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 2 1 3 . 4 6 1 5 4 . 5 3 1 1 . 9 4 7 . 3 7
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 0 . 4 7 0 0 . 2 9 0 A 6 D 4 3 R A 2 9 A A 6 D 4 3 R A 2 9 C A 6 D 4 3 R A 2 9 E A 6 D 4 3 R A 2 9 F
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2 1 1 . 9 4 7 . 3 7
.150" [3.81] Row-to-Row (Dim. “H”) Spacing
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 0 . 4 2 0 0 . 2 4 0
A 6 D 0 6 R A 2 9 A M 2 3 3 A 6 D 0 6 R A 2 9 C M 2 3 3 A 6 D 0 6 R A 2 9 E M 2 3 3 A 6 D 0 6 R A 2 9 F M 2 3 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1 1 0 . 6 7 6 . 1 0
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 0 . 4 2 0 0 . 2 4 0
A 6 D 1 0 R A 2 9 A M 2 3 3 A 6 D 1 0 R A 2 9 C M 2 3 3 A 6 D 1 0 R A 2 9 E M 2 3 3 A 6 D 1 0 R A 2 9 F M 2 3 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6 1 0 . 6 7 6 . 1 0
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 0 . 4 2 0 0 . 2 4 0
A 6 D 1 2 R A 2 9 A M 2 3 3 A 6 D 1 2 R A 2 9 C M 2 3 3 A 6 D 1 2 R A 2 9 E M 2 3 3 A 6 D 1 2 R A 2 9 F M 2 3 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9 1 0 . 6 7 6 . 1 0
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 0 . 4 2 0 0 . 2 4 0
A 6 D 1 5 R A 2 9 A M 2 3 3 A 6 D 1 5 R A 2 9 C M 2 3 3 A 6 D 1 5 R A 2 9 E M 2 3 3 A 6 D 1 5 R A 2 9 F M 2 3 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7 1 0 . 6 7 6 . 1 0
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 0 . 4 2 0 0 . 2 4 0
A 6 D 1 8 R A 2 9 A M 2 3 3 A 6 D 1 8 R A 2 9 C M 2 3 3 A 6 D 1 8 R A 2 9 E M 2 3 3 A 6 D 1 8 R A 2 9 F M 2 3 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6 1 0 . 6 7 6 . 1 0
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 0 . 4 2 0 0 . 2 4 0
A 6 D 2 2 R A 2 9 A M 2 3 3 A 6 D 2 2 R A 2 9 C M 2 3 3 A 6 D 2 2 R A 2 9 E M 2 3 3 A 6 D 2 2 R A 2 9 F M 2 3 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1 1 0 . 6 7 6 . 1 0
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 0 . 4 2 0 0 . 2 4 0
A 6 D 2 5 R A 2 9 A M 2 3 3 A 6 D 2 5 R A 2 9 C M 2 3 3 A 6 D 2 5 R A 2 9 E M 2 3 3 A 6 D 2 5 R A 2 9 F M 2 3 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0 1 0 . 6 7 6 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 0 . 4 2 0 0 . 2 4 0
A 6 D 2 8 R A 2 9 A M 2 3 3 A 6 D 2 8 R A 2 9 C M 2 3 3 A 6 D 2 8 R A 2 9 E M 2 3 3 A 6 D 2 8 R A 2 9 F M 2 3 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8 1 0 . 6 7 6 . 1 0
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 0 . 4 2 0 0 . 2 4 0
A 6 D 3 6 R A 2 9 A M 2 3 3 A 6 D 3 6 R A 2 9 C M 2 3 3 A 6 D 3 6 R A 2 9 E M 2 3 3 A 6 D 3 6 R A 2 9 F M 2 3 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8 1 0 . 6 7 6 . 1 0
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 4 0 . 4 2 0 0 . 2 4 0
A 6 D 4 0 R A 2 9 A M 2 3 3 A 6 D 4 0 R A 2 9 C M 2 3 3 A 6 D 4 0 R A 2 9 E M 2 3 3 A 6 D 4 0 R A 2 9 F M 2 3 3
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 3 1 0 . 6 7 6 . 1 0
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 0 . 4 2 0 0 . 2 4 0
A 6 D 4 3 R A 2 9 A M 2 3 3 A 6 D 4 3 R A 2 9 C M 2 3 3 A 6 D 4 3 R A 2 9 E M 2 3 3 A 6 D 4 3 R A 2 9 F M 2 3 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2 1 0 . 6 7 6 . 1 0
57
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Card Edge Polarization Keys
Description/Application
Tyco Electronics can pro-
vide polarization keys in the
basic configuration shown
on this page. Our Modified
Bellows and Cantilever
Beam Series Card Edge
Connectors use these keys.
The part number and the
connector series for which it
was designed are listed in
the table below.
Ordering Information
Acquired Part Used on Connector Shown on
Number Series Pages
98014-01 Modified Bellows 41-56
98014-01 Cantilever Beam 28-40
.24
[6.10]
45°
Break Off Point
.19
[4.83]
.033
[.84]
Daughter Card
Contact Spacing Dim A Dim B
Non-Accum. ±.005 (.13)
.100 [2.54] .093 [2.36] .052 [1.32]
.125 [3.18] .093 [2.36] .052 [1.32]
.156 [3.96] .105* [2.67] .094 [2.39]
* Except MIL-C-21097E 8–4 which is .070 [1.78]
NOTES:
1. Dimensions are in inches
2. Unless otherwise specified, tolerance is ±.005 [0.13 mm] for three place
decimals.
3. Number of contact fingers shall be the same as the corresponding printed
wiring connector.
.062 [1.57]
Board Thickness
Slot Depth
Min.
Dim. A (Per Applicable Catalog Page)
Dim. B
Contact Spacing
See Note 3
Per MIL-C-21097E
.015
[.38]
30°
Card Edge Connectors Recommended Daughter Card Edge Pattern
58
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
58
Low Profile Connectors
For printed circuit board
packaging, AMP Low Profile
Edge Connectors provide
high performance, low cost
connections on .125 [3.18]
and .156 [3.96] centerline
spacings. .100 [2.54] cen-
terline connectors can be
made available, consult
Tyco Electronics.
Mounted connector hous-
ings extend only .460
[11.68] from the mother
board to allow efficient use
of available space.
These low profile connec-
tors are available in 6
through 43 dual position
sizes on .156 [3.96] center-
line spacing and with 6
through 50 dual positions
on .125 [3.18] centers.
Connectors are supplied
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
Low profile housing is .460
[11.68] deep
6 through 43 dual positions
on .156 [3.96] centerline;
6 though 50 dual positions
on .125 [3.18] centerline
Solder eyelet for wire-to-
board or solder post for
mother-daughter board
application
Selective gold plating of
contact area for high
performance at low cost
Alternate platings are
available on request
Contacts bifurcated for
redundancy
Tin plate for high solder-
ability of solder eyelets
and posts
Accepts .055-.070 [1.40-
1.78] thick printed circuit
boards
Housings available with or
without mounting ears
Intercontact keying
available
UL 94V-0 rated, glass-filled
polyester housings
Variety of solder post
lengths
5 ampere current rating
per contact*
Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
with either solder posts for
mother-daughter board
applications or solder eye-
let contacts for wire-to-
board use.
Low Profile Edge Connec-
tors feature clear slot entry
and accept .055-.070
[1.40-1.78] thick double-
sided printed circuit boards.
Solder posts are available
with .150 [3.18] and .180
[4.57] long tails on .140
[3.56] or .200 [5.08] row-
to-row spacing.
Impact-resistant thermo-
plastic housing, UL rated
94V-0, have molded-in
cavity identification and are
available with or without
mounting ears. Additional
features of the housings
include intercontact keying
provisions, probe slots and
identification of number one
position.
The precision formed con-
tacts made of phosphor
bronze are gold plated on
the contact mating surface
only. This selective plating
provides high reliability
while maintaining low cost.
Solder eyelets and posts
are tin plated for excellent
solderability. The contact is
bifurcated for redundancy.
Shorting contacts are
available.
All connector configurations
are furnished preloaded.
Selectively loaded connec-
tors can be made available
for added economy.
59
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors, .125 [3.18] Centerline
Material and Finish:
Housing—Green, glass-filled
polyester
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] gold in con-
tact area; .000100 [0.00254] bright tin
on posts, with entire contact under-
plated .000030 [0.00076] nickel
Related Product Data:
Keying Plug—page 63
PC Board Hole Layouts—See below
PC Board Edge Pattern—page 63
Technical Documents:
(pages 186, 187):
Product Specification
108-9044
Instruction Sheet 408-7772
Flow Solder Post
.200 [5.08] Row-to-Row Spacing
Recommended
PC Board Hole Layout Recommended
PC Board Hole Layout
Flow Solder Post
.140 [3.56] Row-to-Row Spacing Solder Eyelet Contact
.235 [5.97] Row-to-Row Spacing
.300
[7.62]
.150
[3.81]
.460
[11.68]
.250
[6.35]
.295
[7.49]
.165
[4.19]
.140
[3.56]
.140
[3.56]
.070
[1.78]
.125
[3.18]
.200
[5.08]
.100
[2.54]
.125
[3.18]
.200
[5.08]
.295
[7.49]
.295
[7.49]
.165
[4.19]
.165
[4.19]
.125
[3.18]
A
B
D
B
B
E
C
.125
[3.18] Typ.
. 1 2 5
[3.18] R e f .
.128
[3.25] Dia. .052
[1.32] Dia. .128
[3.25] Dia. .052
[1.32] Dia.
.335
[8.51]
Typ.
.335
[8.51]
Typ.
. 1 2 5
[3.18] R e f . . 1 2 5
[3.18] R e f .
.280
[7.11] Ref.
.235
[5.97] Ref.
.125
[3.18] Typ.
Molded Characters (Upper and Lower Case
Letters Omitting Letters G, I, O &Q)
#1 Cavity Identification
Post Length
(See Chart)
Post Length
(See Chart)
.128
[3.25] Dia.
2 (Plcs.)
PCBoard Thickness—
.055-.070 [1.40-1.78]
123 456
A B C D E F
60
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
60
Low Profile Connectors, .125 [3.18] Centerline (Continued)
Flow Solder Post
.200 [5.08] Row-to-Row
Spacing
No. of Dimensions Post With Without
Dual Mounting Mounting
Positions ABCDELength* Ears Ears
.875 .370 1.035
622.23 9.40 26.29 .150 2-530671-1
1.375 1.795 .370 1.535 2.055 .150 2-530671-2
10 34.93 45.59 9.40 38.99 52.20 .180 2-530663-2
2.000 2.420 .370 2.160 2.680
15 50.80 61.47 9.40 54.86 68.07 .150 2-530671-3
2.375 2.795 .370 2.535 3.055
18 60.33 70.99 9.40 64.39 77.60 .180 2-530663-4 2-530671-4
2.875 3.295 .370 3.035 3.555
22 73.03 83.69 9.40 77.09 90.30 .150 2-530662-5 2-530671-5
3.125 .370 3.285
24 79.38 9.40 83.44 .150 3-530671-3
3.625 4.045 .370 3.785 4.305
28 92.08 102.74 9.40 96.14 109.35 .150 2-530662-6 2-530671-6
3.875 .370 4.035
30 98.43 9.40 102.49 .150 2-530671-7
4.625 5.045 .370 4.785 5.305 .150 2-530671-9
36 117.48 128.14 9.40 121.54 134.75 .180 2-530672-9
5.125 5.545 .437 5.285 5.805
40 130.18 140.84 11.10 134.24 147.45 .150 3-530671-0
6.375 6.795 .437 6.535 7.055
50 161.93 172.59 11.10 165.99 179.20 .150 3-530662-2
Flow Solder Post
.140 [3.56] Row-to-Row
Spacing
Solder Eyelet Contact
.235 [5.97] Row-to-Row
Spacing
No. of Dimensions Post With Without
Dual Mounting Mounting
Positions ABCDELength* Ears Ears
2.000 .370 2.160 .150 2-530673-3
15 50.80 9.40 54.86
3.625 .370 3.785 .150 2-530673-6
28 92.08 9.40 96.14 .180 2-530674-6
6.375 6.795 .437 6.535 7.055
50 161.93 172.59 11.10 165.99 179.20 .180 3-530659-2
No. of Dimensions With
Dual Mounting
Positions ABCDE Ears
2.000 2.420 .370 2.160 2.680
15 50.80 61.47 9.40 54.86 68.07 2-530664-3
2.875 3.295 .370 3.035 3.555
22 73.02 83.69 9.40 77.08 90.29 2-530664-5
3.625 4.045 .370 3.785 4.305
28 92.08 102.74 9.40 96.14 109.35 2-530664-6
5.125 5.545 .437 5.285 5.805
40 130.17 140.84 11.10 134.23 147.44 3-530664-0
6.375 6.795 .437 6.535 7.055
50 161.92 172.59 11.10 165.98 179.19 3-530664-2
*Metric equivalents for post length are .150 = [3.81]; .180 = [4.57].
Note: Other connector sizes can be made available, consult Tyco Electronics.
61
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors, .156 [3.96] Centerline
Material and Finish:
Housing—Green, glass-filled
polyester
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] gold in con-
tact area; .000100 [0.00254] bright tin
on posts, with entire contact under-
plated .000030 [0.00076] nickel
Insert—Brass
Mounting Ear
with Insert
.300
[7.62]
.150
[3.81]
A
B
D
E
C
.160
[4.06] .156
[3.96] Typ.
Molded Characters (Upper and Lower Case
Letters Omitting Letters G, I, O &Q)
#1 Cavity Identification
.128
[3.25] Dia.
(2 Plcs.)
PCBoard Thickness—
.055-.070 [1.40-1.78]
Threaded Inserts
4-40 NC-2B
(2 per connector)
.460
[11.68]
.250
[6.35]
.156
[3.96] Typ.
Flow Solder Post
.200 [5.08] Row-to-Row Spacing
Recommended
PC Board Hole Layout Recommended
PC Board Hole Layout
Flow Solder Post
.140 [3.56] Row-to-Row Spacing Solder Eyelet Contact
.235 [5.97] Row-to-Row Spacing
.295
[7.49]
.165
[4.19]
.140
[3.56]
.140
[3.56]
.070
[1.78]
.156
[3.96]
.200
[5.08]
.100
[2.54]
.156
[3.96]
.200
[5.08]
.295
[7.49]
.295
[7.49]
.165
[4.19]
.165
[4.19]
B
B
.125
[3.18] Ref.
.128
[3.25] Dia. .052
[1.32] Dia. .128
[3.25] Dia. .052
[1.32] Dia.
.378
[9.59]
Typ.
.378
[9.59]
Typ.
.125
[3.18] Ref. .125
[3.18] Ref.
.280
[7.11] Ref.
.235
[5.97] Ref.
Post Length
(See Chart)
Post Length
(See Chart)
Related Product Data:
Keying Plug—page 63
PC Board Hole Layouts—See below
PC Board Edge Pattern—page 63
Technical Documents:
(pages 186, 187):
Product Specification
108-9044
Instruction Sheet 408-7772
12 3 456
A B C D E F
62
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
62
Low Profile Connectors, .156 [3.96] Centerline (Continued)
Flow Solder Post
.200 [5.08] Row-to-Row
Spacing
No. of Dimensions Post With With Without
Dual Mounting Mounting Ears Mounting
Positions A B C D E Length* Ears and Inserts Ears
1.100 1.535 .370 1.240 1.785 2-530655-1 2-530677-1
627.94 38.99 9.40 31.50 45.34 .150 12-530689-11 2-530666-1
1.724 2.159 .370 1.864 2.409 .150 2-530655-2 2-530666-2
10 43.79 54.84 9.40 47.35 61.19 .180 2-530656-2
2.036 2.471 .370 2.176 2.721
12 51.71 62.76 9.40 55.27 69.11 .150 2-530655-3 2-530666-3
2.504 2.939 .370 2.644 3.189 2-530655-4 2-530666-4
15 63.60 74.65 9.40 67.16 81.00 .150 12-530689-41
2.972 3.407 .370 3.112 3.657 .150 2-530655-5 2-530666-5
18 75.49 86.54 9.40 79.04 92.89 .180 2-530667-5
3.596 4.031 .370 3.736 4.281 2-530655-6 2-530666-6
22 .150 12-530689-6112-531433-41
91.34 102.39 9.40 94.89 108.74 .180 2-530656-6 2-530678-6 2-530667-6
4.064 4.499 .370 4.204 4.749 .150 2-530655-8 12-531433-11
25 103.23 114.27 9.40 106.78 120.62 .180 2-530656-8 2-530666-8
4.532 4.967 .370 4.672 5.217 .150 3-530655-2 3-530666-2
28 115.11 126.16 9.40 118.67 132.51 .180 3-530656-2
4.844 5.279 .437 4.984 5.529 .150 2-530655-9 2-530666-9
30 123.04 134.09 11.10 126.59 140.44 12-530689-91
.180 2-530667-9
5.780 6.215 .437 5.920 6.465 .150 3-530655-0 12-531433-21
36 146.18 157.86 11.10 150.37 164.21 .180 13-530689-01 2-530667-0
6.872 7.307 .437 7.012 7.557 .150 3-530655-3 3-530677-3 3-530666-3
43 174.55 185.60 11.10 178.10 191.95 .180 3-530656-3 3-530667-3
Flow Solder Post
.140 [3.56] Row-to-Row
Spacing
and
Solder Eyelet Contact
.235 [5.97] Row-to-Row
Spacing
*Metric equivalents for post length are .150 = [3.81]; .180 = [4.57].
1For .040 [1.02] diameter hole.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Flow Solder Post Solder Eyelet Contact
No. of Dimensions Post With Without With Without
Dual Length* Mounting Mounting Mounting Mounting
Positions ABCDE Ears Ears Ears Ears
1.100 1.535 .370 1.240 1.785
627.94 38.99 9.40 31.50 45.34 .150 2-530654-1
1.724 2.159 .370 1.864 2.409
10 43.79 54.84 9.40 47.35 61.19 .150 2-530657-2 2-530654-2
2.504 2.939 .370 2.644 3.189 .150 2-530657-4 2-530654-4 2-530667-4
15 63.60 74.65 9.40 67.16 81.00 .180 2-530669-4
2.972 3.407 .370 3.112 3.657
18 75.49 86.54 9.40 79.04 92.89 .150 2-530668-5 2-530654-5
3.596 4.031 .370 3.736 4.281
22 91.34 102.39 9.40 94.89 108.74 .150 2-530657-6 2-530668-6 2-530654-6
3.908 4.343 .370 4.048 4.593
24 99.26 110.31 9.40 102.81 116.66 .150 2-530654-7
4.532 4.967 .370 4.672 5.217
28 115.11 126.16 9.40 118.67 132.51 .150 3-530657-2 3-530668-2 3-530654-2
4.844 5.279 .437 4.984 5.529
30 123.04 134.09 11.10 126.59 140.44 2-530654-9
5.780 6.215 .437 5.920 6.465 .150 3-530654-0
36 146.81 155.58 11.10 150.36 164.21 .180 3-530669-0
6.872 7.307 .437 7.012 7.557
43 174.55 185.60 11.10 178.10 191.95 .150 3-530657-3 3-530654-3
63
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors (Continued)
Material: Glass-filled nylon
Part No. 650025-2
Keying Plug
Recommended PC Board
Edge Patterns .125 [3.18] Centerline Boards
Intercontact Key
.156 [3.96] Centerline Boards
.300
[7.52] Min.
.300
[7.52] Min.
.175
[4.45] Min.
Recommended
Gold Area
.175
[4.45] Min.
Recommended
Gold Area
Intercontact
KeySlot
Intercontact
KeySlot
.125
[3.18]
.156
[3.96]
.160
[4.06]
.400
[10.16]
.050
[1.27]
.050
[1.27]
.125
[3.18]
.400
[10.16]
.078±.005
.000
[1.98±0.13]
0.00
.094±.005
.000
[2.39±0.13]
0.00
64
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
64
Twin Leaf Mother Board Connectors
Product Facts
Wide variety of sizes avail-
able from 3 dual positions
and up—no initial tooling
investment required for new
versions
Connectors can be selec-
tively loaded with contacts
in custom patterns
Connectors tooled on all
standard centerlines—
.100 [2.54], .125 [3.18],
.150 [3.81], .156 [3.96],
and .200 [5.08]
Note: .200 [5.08] centerline capabili-
ties provided by loading every-other
dual position of .100 [2.54] centerline
housings.
Closed card entry protects
contacts and daughter
board pads
Adapts to a wide range of
mother board thicknesses
to .104 [2.64] maximum
Phosphor bronze contacts
selectively plated for top
performance and maximum
economy
Protective channel helps
prevent overstress of
contacts
Daughter board keying
available in intercontact or
on-contact styles
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
The AMP Twin Leaf
Connector is a highly
reliable, low-cost mother/
daughter board connector
designed for solid-state
circuitry. The one-piece,
multi-contact connector
requires no front-end tooling.
This versatile connector for
double-sided printed circuit
boards uses preloaded
contacts and selective plat-
ing to give lowest applied
cost. Critical contact areas
are gold-over-nickel plated
to provide positive electrical
connection between con-
tacts and daughter board
pads. Contact posts are tin
plated for efficient dip
soldering to mother boards
up to .104 [2.64] thick.
The Twin Leaf Connector
delivers high reliability
because the contacts
possess superior tolerance
of environmental stresses
including shock, vibration
and variations of tempera-
ture and humidity. Other
characteristics such as high
insulation resistance, low
Performance Specifications
Contact Rating*:
3 amperes continuous
Temperature Rating:
–55°C to +105°C
Insulation Resistance:
5,000 megohms
Dielectric Withstanding Voltage:
Test Voltage (AC, RMS)
Altitude Contact Spacing
.100 [2.54] .150 [3.81]
Sea Level 1,000 1,500
50,000 ft
15 240 m 400 600
70,000 ft
21 336 m 280 400
Termination Resistance:
10 milliohms, max.
Durability: Tested to 100 cycles
(engage/withdraw)
Contact Plating: .000015 [0.00038]
selective gold plating on contact area;
bright tin on solder tine
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
termination resistance, long
life and moderate contact
separation force meet
industry requirements for
reliability. Connectors are
tooled in sizes from 3
through 80 dual-contact
positions with contacts on
.100 [2.54], .125 [3.18],
.150 [3.81], .156 [3.96]
or .200 [5.08] centers.
Other sizes and custom-
loaded contact patterns
are available on request.
The connector housing,
made of glass-filled poly-
ester with a UL 94V-0
rating, features a standoff
which facilitates the use of a
probe for electrical continuity
checks without risk of dam-
age to the contacts. A
closed card-entry design of
the housing protects the
contacts and daughter
board pads. Housings
accept daughter boards
ranging from .055 [1.40] to
.070 [1.78] in thickness.
Intercontact and on-contact
keys are available for
polarization of the housings.
Card guides or end caps
make alignment of daughter
board pads with Twin Leaf
Connector contacts quick
and easy.
65
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors Without End Caps
*Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines, except where noted;
.170 [4.32] for .100 [2.54] and .125 [3.18] centerlines, except where noted.
A
A
.010 x .024
[0.25 x 0.61]
Post for .035 [0.89]
Dia. Hole
Fit for
.055-.070
[1.4-1.78]
PCBoard
.135* .170*
[3.43] or [4.32]
.400
[10.16]
.225
[5.72]
.610
[15.49]
.200
[5.08]
Card Slot
Depth
.400 [10.16]
Max.
.100 [2.54], .125 [3.18],
.150 [3.81] and
.156 [3.96] Centerlines,
With Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000015 [0.00038] gold in contact area;
tin on posts, with entire contact under-
plated .000030 [0.00076] nickel, except
where noted
Related Product Data:
Performance Specifications
page 64
Card Guides—pages 70, 71
Keying Plugs—page 72
PC Board Hole Layouts—page 71
Technical Documents:
(pages 186, 187):
Product Specification
108-9027
Instruction Sheets 408-7479,
408-7498, 408-7506
B
D
66
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
66
Twin Leaf Mother Board Connectors Without End Caps
A = .100 [2.54] A = .125 [3.18] A = .150 [3.81] A = .156 [3.96]
No. of Centerline Spacing Centerline Spacing Centerline Spacing Centerline Spacing
Dual B D Part B D Part B D Part B D Part
Positions Numbers Numbers Numbers Numbers
.300 .600
2 7.62 15.24 1,31-583694-1
.200 .400 .300 .600 .312 .624
35.08 10.16 583485-6 7.62 15.24 1,31-645155-11,3 7.92 15.85 4-583486-8
.450 .750
4 11.43 19.05 583407-5
.400 .600 .600 .900
510.16 15.24 583485-7 15.24 22.86 583407-6
1.050 1.350
8 26.67 34.29 583407-9
1.000 1.250
9 25.40 31.75 583533-7
.900 1.100 1.400 1.720
10 22.86 27.94 1-583485-2 35.56 43.69 4-583486-1
1.500 1.800
11 38.10 45.72 1-583407-2
1.300 1.500
14 33.02 38.10 1-583485-6
2.100 2.400
15 53.34 60.96 1-583407-5
2.125 2.375 2.652 2.964
18 53.97 60.32 1-583533-6 67.36 75.28 3-583486-3
2.850 3.150 2-583407-0
20 72.39 80.01 530292-93
2.625 2.875
22 66.67 73.02 2-583533-0
4.050 4.350 4.212 4.524
28 102.87 110.49 583407-1 106.99 114.91 2-583486-3
3.625 3.875 4.524 4.836
30 92.08 98.43 531534-22 114.91 122.83 2-583486-1
4.500 4.800
31 53.34 60.96 530292-33
4.992 5.304
33 126.80 134.72 1-583486-8
5.460 5.772
36 138.68 146.61 1-583486-5
4.875 5.125 5.850 6.150 6.084 6.396
40 123.83 130.18 3-583533-8 148.59 156.21 3-583407-8 154.53 162.46 1-583486-1
6.552 6.864
43 166.42 174.35 583486-8
4.900 5.100 6.130 6.380 7.350 7.650 7.640 7.960
50 124.46 129.54 583485-3 155.70 162.05 5-583533-01186.69 194.31 4-583407-8 194.06 202.18 583486-1
8.580 8.892
56 217.93 225.86 5-583486-0
6.400 6.600
65 162.56 167.64 5-583485-6
7.900 8.100
80 200.66 205.74 5-583485-5
1Contacts are plated .000030 [0.00076] gold in contact area, tin on posts, with entire contact underplated .000030 [0.00076] nickel.
2Post length .135 [3.43]
3Post length .170 [4.32]
Note: Other connector sizes can be made available, consult Tyco Electronics.
67
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors With End Caps
**Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines;
.170 [4.32] for .100 [2.54] and .125 [3.18] centerlines.
**See page 27 for dimensions.
F
A
G
.010 x .024
[0.25 x 0.61]
Post for .035 [0.89]
Dia. Hole
Fit for
.055-.070
[1.4-1.78]
PCBoard
.135* .170*
[3.43] or [4.32]
.400
[10.16]
.225
[5.72]
.610
[15.49]
.200
[5.08]
.062
[1.58]
Card Slot
Depth
.400 [10.16]
Max.
Accepts #2
Self-tapping
Screw
.100 [2.54], .125 [3.18],
.150 [3.81] and
.156 [3.96] Centerlines,
With Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000015 [0.00038] gold in contact area;
tin on posts, with entire contact under-
plated .000030 [0.00076] nickel
Related Product Data:
Performance Specifications
page 64
Keying Plugs—page 72
PC Board Hole Layouts—page 71
Technical Documents:
(pages 186, 187):
Product Specification
108-9027
Instruction Sheets 408-7479,
408-7498, 408-7506
B E**
68
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
68
Twin Leaf Mother Board Connectors With End Caps
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of A = .100 [2.54] Centerline Spacing A = .125 [3.18] Centerline Spacing A = .150 [3.81] Centerline Spacing A = .156 [3.96] Centerline Spacing
Dual Part Part Part Part
Pos. B F G Numbers B F G Numbers B F G Numbers B F G Numbers
.200 .400 .734
35.03 10.16 18.64 1-583715-1
.400 .600 .934
510.16 15.24 23.72 1-583715-3
.500 .700 1.034 .625 .875 1.259 .780 1.092 1.538
612.70 17.78 26.26 1-583715-4 15.88 22.23 31.96 1-583679-5 19.81 27.74 39.07 1-583660-6
.600 .800 1.134
715.24 20.32 28.80 1-583715-5
.800 1.000 1.334
920.32 25.40 33.88 1-583715-7
.900 1.100 1.434 1.404 1.716 2.162
10 22.86 27.94 36.42 1-583715-8 35.66 43.59 54.91 1-583660-0
1.100 1.300 1.634 1.716 2.028 2.474
12 27.94 33.02 41.50 1-583715-0 43.58 51.51 62.84 1-583660-2
1.200 1.400 1.734
13 30.48 35.56 44.04 1-583715-1
1.950 2.250 2.684 2.028 2.340 2.786
14 49.53 57.15 68.17 1-583692-3 51.51 59.44 70.76 1-583660-4
1.400 1.600 1.934 2.100 2.400 2.834 2.184 2.496 2.942
15 35.56 40.64 49.12 1-583715-3 53.34 60.96 71.98 1-583692-4 55.47 63.40 74.73 1-583660-2
1.600 1.800 2.134 2.000 2.250 2.634
17 40.64 45.72 54.20 1-583715-5 50.80 57.15 66.90 1-583679-6
1.700 1.900 2.234 2.125 2.375 2.759 2.652 2.964 3.410
18 43.18 48.26 56.74 1-583715-6 53.98 60.33 70.08 1-583679-7 67.36 75.28 86.61 1-583660-7
1.900 2.100 2.434 2.375 2.625 3.009
20 48.26 53.34 61.82 1-583715-8 60.33 66.68 76.43 1-583679-9
3.276 3.588 4.034
22 83.21 91.14 102.46 2-583660-1
2.400 2.600 2.934 3.000 3.250 3.634 3.600 3.900 4.334 3.744 4.065 4.502
25 60.96 66.04 74.52 2-583715-3 76.20 82.55 92.30 2-583679-4 91.44 99.06 110.08 2-583692-4 95.10 103.02 114.35 2-583660-4
2.500 2.700 3.034
26 63.50 68.58 77.05 2-583715-4
2.700 2.900 3.234 3.375 3.625 4.009 4.212 4.524 4.979
28 68.58 73.66 82.14 2-583715-6 85.73 92.08 101.83 2-583679-6 106.98 114.91 126.24 2-583660-7
2.900 3.100 3.434 4.350 4.650 5.084 4.524 4.836 5.282
30 73.66 78.74 87.22 2-583715-8 110.49 118.11 129.13 1-583692-1 114.91 122.83 134.16 2-583660-9
3.000 3.200 3.534
31 76.20 81.28 89.76 2-583715-9
3.100 3.300 3.634 4.836 5.148 5.594
32 78.74 83.82 92.30 3-583715-0 122.83 130.76 142.09 3-583660-1
4.800 5.100 5.534
33 121.92 129.54 140.56 3-583692-1
3.300 3.500 3.834
34 83.82 88.90 97.38 3-583715-2
3.400 3.600 3.934 5.100 5.400 5.834 5.304 5.616 6.062
35 83.36 91.44 99.92 3-583715-3 129.54 137.16 148.18 3-583692-3 134.72 142.64 153.97 3-583660-4
3.500 3.700 4.034 5.250 5.550 5.984 5.460 5.772 6.218
36 88.90 93.98 102.46 3-583715-4 133.35 140.97 151.99 3-583692-4 138.68 146.61 157.94 1-583660-1
3.900 4.100 4.434 4.875 5.125 5.509 5.850 6.150 6.584
40 99.06 104.14 112.62 3-583715-8 123.83 130.18 139.93 3-583679-8 148.59 156.21 167.23 3-583692-8
4.000 4.200 4.534
41 101.60 106.68 115.16 3-583715-9
6.552 6.864 7.310
43 166.42 174.35 185.67 4-583660-1
4.900 5.100 5.434 6.125 6.375 6.759 7.350 7.650 8.084 7.644 7.956 8.402
50 124.46 129.54 138.02 4-583715-8 155.58 161.93 171.68 4-583679-8 186.69 194.31 205.33 4-583692-8 194.16 202.08 213.41 4-583660-8
7.900 8.100 8.434
80 200.66 205.74 214.22 5-583715-7
69
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors With End Caps (Continued)
Typical Connector and Card Guide Assembly
Double Slotted
Card Guide (Without Stand-off)
End Cap
Daughter Board
Self-tapping #2
Screw (2 Reqd.)
Self-tapping #2
Screw (2 Reqd.)
Stand-off
*Must be .063 [1.59] thick for use with Double Slotted Card Guides.
Self-tapping #2
Screw (1 Reqd.)
Mother Board
.104 [2.64] Max.
Thickness*
Double Slotted
Card Guide (With Stand-off)
Single Slotted
Card Guide
70
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
70
Twin Leaf Mother Board Connectors (Continued)
Card Guides
Material: Glass-filled nylon, black
Part No. 583671-1
Related Product Data:
Connectors used with—page 65
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7498,
408-7506
Single Slotted
Single Slotted Card Guide
and Connector Mounting
Dimensions
A E
.100 .263
2.54 6.68
.125 .288
3.18 7.31
.150 .313
3.81 7.95
.156 .319
3.96 8.10
.210
[5.33]
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.091
[2.31]
Dia.
A
E
Min.
.225
[5.72]
3.770
[95.76]
3.585
[91.06]
.170
[4.32]
.523
[13.28] .225
[5.72]
.137
[3.48]
.074
[1.88] Dia.
Thru Hole
.074 [1.88] Dia. x
.175 [4.45] Deep
71
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors (Continued)
Card Guides
(Continued)
Material: Nylon, natural
Part No. 583425-1
Related Product Data:
Connectors used with—page 65
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7498,
408-7506
Double Slotted Without Stand-off
.080
[2.03]
1.680
[42.67] 1.500
[38.10]
.300
[7.62]
.540
[13.72]
.150
[3.81]
.400
[10.16]
Double Slotted Card Guide
and Connector Mounting
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.310
[7.87]
A
E
Min.
.175
[4.45]
Recommended PC Board
Layout for Connectors
With End Caps
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.100
[2.54]
Dia.
AE
Dimensions
A E
.100 .328
2.54 8.33
.125 .353
3.18 8.96
.150 .376
3.81 9.60
.156 .384
3.96 9.75
Dimensions
A E
.100 .267
2.54 6.78
.125 .317
3.18 8.05
.150 .367
3.81 9.32
.156 .379
3.96 9.62
Note: Mother Board
must be .063 [1.59] thick
for use with Double
Slotted Card Guides.
72
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
72
Twin Leaf Mother Board Connectors (Continued)
Keying Plugs
Other Twin Leaf
Mother Board
Connectors
Material: Nylon, natural
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7479 Type A Type B
Intercontact On-Contact
In-Row Type Connector Style* Intercontact Keying Plug On-Contact Keying Plug
Contact of with without Type A Type B Insertion/Extraction Part Insertion/Extraction
Spacing Contact End Caps End Caps Part Numbers Part Numbers Tool Numbers Tool
.100 Solder Post 583715 583485
2.54 Card Extender 530268 530291 530286-3 91081-2 583714-1 91088-1
.125 Solder Post 583679 583533
3.18 Card Extender 530265 530290 530286-2 530030-1 91081-1 583714-1 91088-1
.150 Solder Post 583692 583407
Wrap-Type Post 583754 583752 530286-2 530030-1 91081-1
3.81 Card Extender 530278 530270
.156 Solder Post 583660 583486
Wrap-Type Post 583755 583753 530286-2 530030-1 91081-1
3.96 Card Extender 530267 530282
*Refer to pages 66-68, as applicable, for specific connector sizes.
A
.475
[12.06]
Min.
Fits for
.055-.070
[1.4-1.78]
PCBoard
.610
[15.49]
.225
[5.72]
.400
[10.16]
Connector Dimension A
Centerlines Intercontact On-Contact
.100 .040 .129
2.54 1.02 3.28
.125 .050 .129
3.18 1.27 3.28
.150 .050 .160
3.81 1.27 4.06
.156 .050 .160
3.96 1.27 4.06
For more information on the connec-
tors shown here, consult Tyco
Electronics.
Recommended PC Board Cutout for Keying Plugs
Card Extender Connectors
Connectors With End Caps
Part Number
Centerlines Series*
.150
3.81 530278
.156
3.96 530267
*Consult Tyco Electronicsfor
specific connector sizes.
73
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors
AMP Rotary Cam Zero
Insertion Force (ZIF) Card
Edge Connectors are avail-
able in sizes to fit most
industry-standard printed
circuit boards. A clockwise
rotation of the cam handle
opens contacts to allow
zero-force insertion or
removal of PC boards—
even boards with a large
number of contacts. Turning
the cam handle to close the
connector locks the board
securely in place. Rotary
Cam ZIF Connectors
accept double-sided PC
boards .054-.070 [1.37-
1.78] thick, with contact
centerline intervals of .100
[2.54], .125 [3.18] and .156
[3.96]. Row-to-row spacing
of connector posts is .200
[5.08] for .100 [2.54] and
.156 [3.96] connectors and
.250 [6.35] for .125 [3.18]
connectors.
Contacts are nickel under-
plated phosphor bronze
with gold plate in the
contact area and tin-lead
plated posts. Contact con-
figurations include vertical
and right-angle solder posts
and wrap-type posts.
Preassembled connectors
feature housings made from
94V-0 rated glass-filled
polyester and mounting
ears for easy mounting to
the mother board. Housings
are available with one end
open, both ends open and
both ends closed for side
and top daughter board
insertion. Integral board
locks secure boards in the
connectors. Accessories
include dust covers, cam
rods (with and without
boots) and cam keys for
nut-driver actuation and
for tandem operation of
connectors.
Performance Specifications
Current vs. Temperature Rise*:
3 amperes at 30°C
Operating Temperature:
–55°C to +105°C
Contact Resistance:
20 milliohms max.
Durability: Tested to 5000 cycles
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
Zero insertion force; little or
no effort required to insert
and withdraw PC boards
Reduced pad wear for
extended board life
Allows all four sides of
board to be used for
input/output functions
Accepts double-sided
boards
Three contact styles to
choose from: vertical solder
post, right-angle solder post
and wrap-type post (2 and 3
high)
Available in .100 [2.54],
.125 [3.18] and .156 [3.96]
centerlines
Three configurations avail-
able: open one end, open
both ends and closed both
ends
Products indicated are
recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
74
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
74
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.250
[6.35]
.050
[1.27]
.018
[0.46]
Typ.
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open Closed
Positions A B C D E* One End1Both Ends1Both Ends
2.100 2.800 3.100 2.300 .125 1-531020-1 1-531019-1
22 53.34 71.12 78.74 58.42 .160 1-531020-1
2.400 3.100 3.400 2.600 .125 1-531020-2 1-531019-2
25 60.96 78.74 86.36 66.04 .160 1-531020-2
2.700 3.400 3.700 2.900
28 68.58 86.36 93.98 73.66 .160 21-531020-3
3.000 3.700 4.000 3.200
31 76.20 93.98 101.60 81.28 .160 2-531020-1
3.500 4.200 4.500 3.700 .125 3-531020-2 1-531019-4
36 88.90 106.68 114.30 93.98 .160 1-531020-4
3.900 4.600 4.900 4.100 .125 1-531020-5
40 99.06 116.84 124.46 104.14 .160 1-531020-5
4.200 4.900 5.200 4.400 .125 3-531020-3
43 1-531020-7
106.68 124.46 132.08 111.76 .160 22-531020-82
4.900 5.600 5.900 5.100 .125 1-531020-8 531021-8
50 1-531020-8 1-531019-8
124.46 142.24 149.86 129.54 .160 22-531020-92
5.900 6.600 6.900 6.100
60 149.86 167.64 175.26 154.94 .160 1-531020-9 1-531021-9 1-531019-9
6.400 7.100 7.400 6.600 .125 1-531020-0
65 2-531020-0
162.56 180.34 187.96 167.64 .160 23-531020-02
*Metric equivalents in millimeters for post lengths Eare .125 = [3.18]; .160 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
2Connectors without cam rod and boardlock.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
75
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)
Right-Angle Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—page 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18]
Closed End
B
A
D
C
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.100
[2.54]
.250
[6.35]
.050
[1.27]
.160
[4.06]
.200
[5.08]
Closed
Position
.150
[3.81]
.370
[9.40]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Bend Part Numbers
Dual (Open End1)
Positions A B C D Right
2.400 3.100 3.400 2.800
25 60.96 78.74 86.36 71.12 R1-531395-23
3.500 4.200 4.500 3.700
36 88.90 106.68 114.30 93.98 R1-531396-4
4.900 5.600 5.900 5.100
50 124.56 142.24 149.86 129.54 L 1-531396-8
6.400 7.100 7.400 6.600
65 162.56 180.34 187.96 167.64 R 1-531396-0
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown.
2. Other connector sizes can be made available, consult Tyco Electronics.
3. Open both ends.
Bend Right Shown
76
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
76
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)
Vertical Connector,
Wrap-Type Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.250
[6.35]
.050
[1.27]
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open
Positions A B C D E* One End1Both Ends1
2.400 3.100 3.400 2.600
25 60.96 78.74 86.36 66.04 .380 1-531414-2
3.500 4.200 4.500 3.700 .580 1-531414-4 1-531415-4
36 88.90 106.68 114.30 93.98 .380 1-531414-4
3.900 4.600 4.900 4.100
40 99.06 116.84 124.46 104.14 .580 1-531414-5
4.100 4.800 5.100 4.300
42 104.14 121.92 129.54 109.22 .380 1-531414-6
4.900 5.600 5.900 5.100
50 124.46 142.24 149.86 129.54 .580 2-531414-4 1-531415-8
5.900 6.600 6.900 6.100
60 149.86 167.64 175.26 154.94 .580 1-531414-9
6.400 7.100 7.400 6.600
65 162.56 180.34 187.96 167.64 .580 1-531414-0
*Metric equivalents in millimeters for post lengths Eare . 5 8 0 = [14.73] (3-high wrap-type); . 3 8 0 = [9.65] (2-high wrap-type).
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
.025
[0.64]
Typ.
77
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .125 x .250 [3.18 x 6.35] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186,187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ. .018
[0.46]
Typ.
.125
[3.18]
Typ.
.250
[6.35]
.050
[1.27]
.250
[6.35]
Closed
Position
.150
[3.81]
.370
[9.40]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open
Positions A B C D E* One End1Both Ends1
3.375 4.125 4.425 3.625
28 85.73 104.76 112.40 92.08 .125 1-531024-3
3.625 4.375 4.675 3.875
30 92.08 111.13 118.75 98.43 .125 1-531023-4
4.875 5.625 5.925 5.125
40 123.83 142.88 150.50 130.18 .160 1-531023-4 1-531024-4
*Metric equivalents in millimeters for post lengths Eare . 1 2 5 = [3.18]; . 1 6 0 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
78
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .156 x .200 [3.96 x 5.08] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.156
[3.96]
Typ.
.250
[6.35]
.050
[1.27]
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open Closed
Positions A B C D E* One End1Both Ends1Both Ends
3.276 4.088 4.388 3.588 .125 531025-3
22 83.21 103.83 111.46 91.14 .160 531025-9 531007-9
5.460 6.272 6.572 5.772
36 138.68 159.31 166.93 146.61 .160 1-531026-1
6.552 7.364 7.664 6.864
43 166.42 187.05 194.67 174.35 .125 531025-6
*Metric equivalents in millimeters for post lengths Eare . 1 2 5 = [3.18]; . 1 6 0 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
.018
[0.46]
Typ.
79
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Accessories
Dimension Part
A Numbers
3.185
80.90 650083-1
3.705
94.11 650083-2
4.470
113.54 650083-3
5.285
134.24 650083-4
5.900
149.86 650083-6
5.975
151.77 532563-7
Dimension Part
A Numbers
11.050
280.67 531863-2
48.000
1219.20 531863-1
Dimension Part
A Numbers
6.385
162.18 650083-7
6.985
177.42 650083-8
7.485
190.12 650083-9
7.725
196.22 1-532563-0
8.320
211.34 1-650083-7
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Note: Other lengths can be made available
upon request, consult Tyco Electronics.
Material:
Cam Rod—Stainless steel
Boot—Glass-filled polyester, yellow
Material: Rigid vinyl, black
Dust Covers
Cam Rods with Boot
A
A
.348
[8.84]
.200
[5.08]
.200
[5.08] .400
[10.16]
.835
[21.21]
.654
[16.61]
80
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Accessories (Continued)
Dimension Part
A Numbers
2.200
55.88 2-531004-8
2.700
68.58 2-531004-9
3.300
83.82 3-531004-0
4.750
120.65 2-531004-4
5.000
127.00 1-531004-4
5.500
139.70 2-531004-6
Dimension Part
A Numbers
3.380
85.85 645293-3
4.50
114.30 645293-8
5.200
132.08 645293-6
6.90
175.30 645293-7
13.120
333.25 645293-5
Dimension Part
A Numbers
6.000
152.40 2-531004-7
6.250
158.75 1-531004-6
6.750
171.45 1-531004-7
8.250
209.55 3-531004-2
12.500
317.50 2-531004-0
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Material: Stainless steel
Cam Rods without Boot
A
A
.125
[3.18]
.260
[6.60] .045
[1.14]
.252
[6.40]
.055
[1.40]
.125
[3.18]
.055
[1.40]
.200
[5.08] .045
[1.14]
.775
[19.69]
81
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Recommended PC Board Hole Layouts
A*
A*
Pin No. 1 (Ref.)
PCBoard Edge
W
X
B*
CL
.200
[5.08]
Mother Board Hole Layout, Vertical Through-Board Connectors
*Refer to individual connector specifications.
Mother Board Hole Layout, Right-Angle Through-Board Connectors
CL W X
.100 .200 .350
2.54 5.08 8.89
.125 .250 .375
2.18 6.35 9.53
.156 .200 .406
3.96 5.08 10.31
.048
[1.22] Dia. Typ.
.128
[3.25] Dia.
(2 Plc.)
.048
[1.22] Dia. Typ. .400
[10.16] Max.
.100
[2.54]Typ.
*Refer to individual connector specifications.
82
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Recommended PC Board Edge Pattern
A
CL
CL Minus .006 [0.15]
Daughter Board Edge Pattern
Tandem Application
.270
[6.86]
Min.
.700
[17.78]
Min.
B±.005
[±0.13]
C+.005
-.000
[+0.13]
Note: Contact Tyco Electronics for information concerning special tandem connectors.
Special Application
No. of CL = .100 [2.54] CL = .125 [3.18] CL = .156 [3.96]
Dual C = .050 [1.27] C = .078 [1.98] C = .094 [2.39]
Positions A B A B A B
2.100 2.288 3.267 3.576
22 53.34 58.12 83.21 90.83
2.400 2.588
25 60.96 65.74
2.700 2.888 3.375 3.613
28 68.58 73.36 85.73 91.77
3.625 3.863
30 92.08 98.12
3.000 3.188
31 76.20 80.98
3.500 3.688 5.460 5.760
36 88.90 93.68 138.68 146.30
3.900 4.088 4.875 5.113
40 99.06 103.84 123.83 129.87
4.200 4.388 6.552 6.852
43 106.68 111.46 166.42 174.04
4.900 5.088
50 124.46 129.24
5.900 6.088
60 149.86 154.64
6.400 6.588
65 162.56 167.34
Special Rod
(Part No. Series 645293)
Allows Customer Supplied
Nut Driver Actuation
(Refer to page 80.)
83
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors
AMP Linear Zero Insertion
Force (ZIF) PC Board Edge
Connectors are available in
both lever and bell crank
actuated styles and can be
provided as panel assem-
blies, separate housings
and contacts or as pre-
assembled with solder post
terminals.
Panel assemblies include a
housing with ACTION PIN
press-fit solderless contacts
mounted on an epoxy
board for rack application.
Separate housing assem-
blies and ACTION PIN con-
tacts allow customer
assembly. These can be
mounted as close as .625
[15.88]. More design lati-
tude for high density appli-
cation is provided by the
side entry lever-type con-
nector, permitting use of all
sides of the PC board for
edge-type I/O connections
(see page 133). Where
solder applications are
required, Tyco Electronics
has a line of preassembled
connectors with tin-plated
solder terminals. All these
configurations are available
in a broad range of sizes.
With ZIF style connectors,
intermittencies can occur if
a contact comes to rest on
a piece of foreign matter
(dust and dirt particles)
found on PC boards. To
decrease the probability of
this happening, all connec-
tors have been designed to
include a wiping contact
which produces a wiping
action. This action, pro-
duced by the geometry and
bending movements of the
beam, pushes aside debris
and allows for good electri-
cal connection by cleaning
the actual point of contact.
In addition, all connectors
have removable wings
which make it possible to
repair or replace damaged
cam rails, handles, contacts
and housing modules with-
out removing the entire
housing assembly from the
board.
Performance Specifications
Current vs. Temperature Rise*:
3 amperes at 30°C
Operating Temperature:
–65°C to +85°C
Contact Resistance:
16 milliohms max.
Durability: Tested to 250 cycles
(board-to-contact actuation)
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
Minimizes force needed to
install and remove printed
circuit boards
Available in lever and bell
crank styles
Lever styles allow side and
top card entry
Wiping action contacts
enhance electrical
properties
Contacts on .100 x .100
[2.54 x 2.54] or .125 x .125
[3.18 x 3.18] centers
.025 [0.64] square posts
Accepts PC boards from
.054 to .070 [1.37 to 1.78]
in thickness
Normally closed design
leaves springs in relaxed
position
50 to 175 dual positions
available on .100 [2.54]
centerline connectors and
40 to 140 dual positions
available on .125 [3.18]
centerline connectors
84
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline
Housing with Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] min. gold per
MIL-G-45204 in contact area; .000100
[0.00254] min. tin-lead on post with
entire contact underplated .000050
[0.00127] min. nickel per QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 88
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specification
108-14015
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
Lever Style, Side Entry
No. of Dimensions Part
Dual
Positions ABC Number
6.113 3.400 2.000
35 155.27 86.36 50.80 1-645135-2
11.613 7.900 3.000
80 294.97 200.66 76.20 1-645135-1
13.613 9.900 3.000
100 345.77 251.46 76.20 1-645135-5
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section P-P
*Card slot depth.
.450
[11.43]
.355
[9.02]*
.845
[21.46]
.600
[15.24]
.100
[2.54] .190
[4.83]
.103
[2.62]
.845
[21.46]
.175
[4.45]
P
P
Closed End
Open End
Mounting
Hole C
Mounting
Hole C
1.075
[27.31]
.206
[5.23]
.100
[2.54] Typ.
.500
[12.70]
Max.
A
C
B
Closed
L
Open
C Last Contact Position C First Contact Position
LL
L
85
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Panel Assembly Lever Style, Side Entry
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts
pages 88, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specification
108-14015
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
.343
[8.71]
Max.
Closed End
C
.125
[3.18]
1.555
[39.50]
D
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.100
[2.54]
Typ.
.100
[2.54]
.812
[20.62]
.750
[19.05]
B
Open End
.355
[9.02]
Card Slot
Depth
PC Board
Channel
No. of Dimensions Part
Dual
Positions ABCDNumbers
7.400 10.125 3.000 .615
75 251.46 320.68 76.20 15.62 1-645145-0
9.900 12.625 3.000 .615
100 251.46 320.68 76.20 15.62 1-645145-5
12.900 15.625 3.000 .615
130 251.46 320.68 76.20 15.62 2-645145-1
13.900 16.625 3.000 .615
140 353.06 422.28 76.20 15.62 2-645145-3
14.900 17.625 3.000 .615
150 251.46 320.68 76.20 15.62 2-645145-5
15.900 18.625 3.000 .615
160 403.86 473.07 76.20 15.62 2-645145-7
15.900 18.625 3.000 .455
160 403.86 473.07 76.20 11.56 147400-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
86
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Panel Assembly Lever Style, Top Entry
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts
pages 88, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Product Specifications
108-14015, 108-26003
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
.343
[8.71]
Max.
Closed End
C
.125
[3.18]
1.555
[39.50]
.615
[15.62]
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.100
[2.54]
Typ.
.100
[2.54]
.812
[20.62]
.750
[19.05]
B
Closed End
.355
[9.02]
Card Slot
Depth
PC Board
Channel
No. of Dimensions Part
Dual
Positions ABCNumbers
10.900 13.625 3.000
110 276.86 346.08 76.20 1-645147-7
11.900 14.625 3.000
120 302.26 371.48 76.20 1-645147-9
Note: Other connector sizes can be made available, consult Tyco Electronics.
87
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer sup-
plies, must be applied before opening
connector
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts
pages 88, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14015, 108-26003
Application Specification
108-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
Lever Style, Side Entry
No. of Dimensions Part
Dual
Positions ABC Numbers
7.613 4.900 2.000
50 193.37 124.46 50.80 1-645115-5
11.113 7.400 3.000
75 282.27 187.96 76.20 1-645115-0
11.613 7.900 3.000
80 294.97 200.66 76.20 1-645115-1
13.613 9.900 3.000
100 345.77 251.46 76.20 1-645115-5
14.613 10.900 3.000 1-645115-7
110 371.17 276.86 76.20 3-645115-2
15.113 11.400 3.000
115 383.87 289.56 76.20 1-645115-8
16.113 12.400 3.000
125 409.27 314.96 76.20 2-645115-0
16.613 12.900 3.000
130 421.97 327.66 76.20 2-645115-1
17.613 13.900 3.000
140 447.37 353.06 76.20 2-645115-3
19.613 15.900 3.000
160 498.17 403.86 76.20 3-645115-3
21.113 17.400 3.000
175 536.27 441.96 76.20 3-645115-0
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section P-P
*Card slot depth.
.450
[11.43]
.815
[20.70] .600
[15.24]
.355
[9.02]*
P
P
Closed EndOpen End
Mounting
Hole C .206
[5.23]
A
Ref.
C
B
Closed
L
Open
C Last Contact Position C First Contact Position
LL
88
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
ACTION PIN Contacts with Wiping Feature,
.100 [2.54] Centerline Recommended PC Board Hole Layout and Edge Pattern,
.100 [2.54] Centerline
Material and Finish:
Copper alloy 725, plated .000015
[0.00038] gold per MIL-G-45204 in
contact area; .000001 [0.00003] min.
gold flash per MIL-G-45204 on post
with entire contact underplated .000050
[0.00127] nickel per QQ-N-290
Related Product Data:
Performance Specifications
page 83
ACTION PIN Contact Description
and Application Specification
page 94
Tooling—page 95
Mother Board Hole Layout
Daughter Board Edge Pattern
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-2665
Contact Combs
Reeled Contacts
Number of Dimension Part
Contacts
Per Comb* A Number
5.400
55 137.16 4-119311-1
*At least two (2) contact combs required per housing.
Note: Other sizes can be made available, consult Tyco Electronics.
Note: Other plating combinations and thicknesses can be made available,
consult Tyco Electronics.
Number of Part
Contacts
Per Reel Number
35,000 119196-6
.745
[18.92]
A
(Comb)
B
Min.
A
Max.
B
C
L
C
L
C
.045
[1.14]
Contact Area
1.485
[37.72]
.740
[18.80]
Post Area
.100
[2.54]
.100
[2.54] .070
[1.78]
.100 (No. of Pos. –1) +.196
[2.54 (No. of Pos. –1) +4.98]
.600
[15.24] Ref. .200
[5.08] Min.
.098
[2.49] Typ.
.120
[3.05] Dia.
.047
[1.19] Dia. Typ.
(Solder Post Only)*
.025
[0.64] Sq.
Prenotched
for Breakoff
at Assembly
Prenotched
for Breakoff
at Assembly
*For ACTION PIN post hole diameter, see page 94.
Connector Dimensions
Style A B C
.100 .100 .206 .175
Lever 2.54 2.54 5.23 4.45
Connector Entry Dimensions
Style Style A B
.240
Side 6.10
Lever .240 .320
Top 6.10 8.13
89
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline
Panel Assembly
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts
pages 93, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Lever Style, Side Entry
.343
[8.71] Max.
PC Board
Channel .355
[9.02]
Card Slot
Depth
Open End Closed End
.125
[3.18]
1.555
[39.50]
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.125
[3.18]
.812
[20.62]
.750
[19.05]
B
.125
[3.18] Typ.
.615
[15.62]
C
No. of Dimensions Part
Dual
Positions A B C Numbers
4.875 7.625 2.000
40 123.83 193.68 50.80 1-645146-5
6.875 9.625 3.000
56 174.63 244.48 76.20 1-645146-9
7.375 10.125 3.000
60 187.32 257.17 76.20 1-645146-0
8.875 11.625 3.000
72 225.43 295.28 76.20 1-645146-3
10.375 13.125 3.000
84 250.83 320.68 76.20 1-645146-6
15.375 18.125 3.000
124 390.53 460.38 76.20 2-645146-6
Note: Other connector sizes can be made available, consult Tyco Electronics.
90
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Panel Assembly
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts
pages 93, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Bell Crank Style, Top Entry
.355
[9.02]
Card Slot
Depth
3.620
[91.95] Ref.
(Open)
.125
[3.18]
Closed End
1.555
[39.50]
.615
[15.62]
2.41
[54.38] A.609
[15.47]
.125
[3.18]
B
.750
[19.05]
.935
[23.75] Max.
.125
[3.18] Typ.
No. of Dimensions Part
Dual
Positions A B Numbers
7.375 10.625
60 187.33 269.88 1-645149-0
9.875 13.125
80 250.82 333.38 1-645149-5
13.875 17.125
112 352.43 434.98 2-645149-3
17.375 20.625
140 441.33 523.88 3-645149-0
Note: Other connector sizes can be made available, consult Tyco Electronics.
91
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer
supplied, must be applied before
opening connector
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts
pages 93, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Lever Style, Side Entry
Closed
Closed End
Open End
Open
First Contact Position
*Card slot depth.
Section P-P
.475
[12.07]
.355
[9.02]*
.815
[20.7] .600
[15.24]
1.087
[27.61]
.218
[5.54]
A
Ref.
.115
[2.92]
CP
P
B
C
Mounting Hole
C
L
Mounting Hole
C
L
LLast Contact Position
C
L
No. of Dimensions Part
Dual
Positions A B C Number
14.112 10.375 3.000
84 358.44 263.52 76.20 1-645116-6
16.112 12.375 3.000
100 409.24 314.33 76.20 2-645116-0
17.612 15.775 3.000
112 447.34 400.68 76.20 2-645116-3
19.112 17.275 3.000
124 485.44 438.78 76.20 2-645116-6
Note: Other connector sizes can be made available, consult Tyco Electronics.
92
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer
supplied, must be applied before
opening connector
Performance Specifications
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts
pages 93, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Bell Crank Style, Top Entry
Closed End
First Contact Position
*Card slot depth.
Section P-P
.475
[12.07]
.355
[9.02]*
.815
[20.7]
.600
[15.24]
1.250
[31.75]
1.820
[46.23]
.115
[2.92]
1.062
[26.97]
(Open)
2.562
[65.07]
(Closed)
A
Ref.
.312
[7.92]
.500
[12.70]
.187
[4.75]
.115
[2.92]
1.874
[47.60]
P
P
B
C
Mounting Hole
C
L
Mounting Hole
C
L
LLast Contact Position
C
L
No. of Dimensions Part
Dual
Positions A B Numbers
8.562 6.375
52 217.47 161.93 1-645142-8
9.562 7.375
60 242.87 187.32 1-645142-0
13.125 9.875
80 333.37 250.82 1-645142-5
16.062 13.875
112 407.97 352.43 2-645142-3
Note: Other connector sizes can be made available, consult Tyco Electronics.
93
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
ACTION PIN Contacts with Wiping Feature,
.125 [3.18] Centerline Recommended PC Board Hole Layout and Edge Pattern,
.125 [3.18] Centerline
Material and Finish:
Copper alloy 725, plated .000015
[0.00038] gold per MIL-G-45204 in
contact area; .000001 [0.00003] min.
gold flash per MIL-G-45204 on post
with entire contact underplated .000050
[0.00127] nickel per QQ-N-290
Related Product Data:
Performance Specifications
page 83
ACTION PIN Contact Description
and Application Specification
page 94
Tooling—page 95
Mother Board Hole Layout
Daughter Board Edge Pattern
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-2665
Contact Combs
Number of Dimension Part
Contacts
Per Comb* A Number
6.875
56 174.63 1-119950-2
*At least two (2) contact combs required per housing.
Note: Other sizes can be made available, consult Tyco Electronics.
.750
[19.05]
A
(Comb)
B
Min.
A
Max.
B
C
LC
.045
[1.14]
Contact Area
1.490
[37.85]
.740
[18.80]
Post Area
.125
[3.18]
.125
[3.18]
.125 (No. of Pos. –1) +.220
[3.18 (No. of Pos. –1) +5.59]
.600
[15.24] Ref.
.200
[5.08] Min.
.090
[1.78] Typ.
.110
[2.79] Typ.
.120
[3.05] Dia.
.047
[1.19] Dia. Typ.
(Solder Post Only)*
.025
[0.64] Sq.
Prenotched
for Breakoff
at Assembly
*For ACTION PIN post hole diameter, see page 94.
Connector Dimensions
Style C A B C
.125 .125 .218 .187
Lever 3.18 3.18 5.54 4.75
.125 .125 1.250 .187
Bell-Crank 3.18 3.18 31.75 4.75
Connector Entry Dimensions
Style Style A B
.240
Side 6.10
Lever .240 .320
Top 6.10 8.13
.775 .600
Bell-Crank Top 19.68 15.24
L
94
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
AMP ACTION PIN
Press-Fit Contacts
ACTION PIN contacts provide a reliable press-fit connection.
Localized pressure in the interface area entails oxide
break-through and helps prevent corrosion in the harshest
environments to provide a reliable connection virtually every
time. Also, radial and axial distortion are controlled to meet
today’s standards for multilayer board applications.
PC Board Thickness
ACTION PIN contacts are
designed for use in a variety of
PC board thicknesses. However,
certain ACTION PIN contacts
are to be used in specific ranges
of board thicknesses. To
promote optimum performance,
the recommended board thick-
nesses provided with the con-
nector being used must be
followed.
Annular Ring (See Note)
Drilled Hole
Copper Thickness
Tin-Lead Thickness
Plated Through-Hole
ACTION PIN Contact/PC Board Applications
*Maximum hardness of copper layer is 150 Knoop.
Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].
Connector ACTION PIN Drilled Hole Plating Thicknesses Plated Radial Hole Distortion
Contact Through-Hole
Type Material Thickness DiameterCopper* Tin-LeadDiameterAverage Maximum
.0003
Linear ZIF .025 .0453±.001 .001-.003 0.008 .037-.043 Not Not
0.64 1.151±0.03 0.03-0.08 Min. 0.94-1.09 Specified Specified
95
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
Tooling Assembly tooling is not
required except when
using connectors with
ACTION PIN contacts.
ACTION PIN contact
assembly requires an
arbor-style bench tool with a
capacity of 40 lb [178 N] per
contact, a support fixture,
contact applicator, carrier
removal tool and housing
assembly tool.
Typical procedure is to
place a PC board on the
support fixture, insert contact
combs into the printed circuit
board with the contact appli-
cator and seat with the arbor
tool. Next, remove the carrier
strip from the contact combs
with the carrier break-off tool.
Place the housing over the
contacts with the housing
assembly tool, and repeat
the entire process until the
board is complete.
.100 x .100 [2.54 x 2.54] Centerline Connectors
No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools
Dual Removal Assembly Removal Replacement Insertion
Positions Applicator Tool Tool Tool Tool Tool With Housing Without Housing
50 266267-4 265924-4 313136-1
80 266267-3 265924-4 313136-2
100 266267-4 265924-4
110 266267-5 265924-4 313136-3
115 266267-5 265924-4 313256-1 266233-1 266264-1 266235-1 3-265871-2
120 266267-5 265924-4
125 266267-4 265924-4 313136-4
140 266267-4 265924-4
175 266267-5 265924-4 313136-5
.125 x .125 [3.18 x 3.18] Centerline Connectors
No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools
Dual Removal Assembly Removal Replacement Insertion
Positions Applicator Tool Tool Tool Tool Tool With Housing Without Housing
40 313139-1 265924-4 313136-1
52 313139-2 265924-6
56 313139-2 265924-6 313136-2
60 313139-2 265924-7
72 313139-3 265924-4 313256-1 266233-1 266264-1 266235-1 3-265871-2
84 313139-2 265924-5 313136-3
112 313139-2 265924-7 313136-4
124 313139-2 265924-5
140 313139-2 265924-5 313136-5
96
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
Special Application
Use Linear and Rotary ZIF Connectors as Card Guides
to access more sides of the Daughter Board.
Standard Edge II
(pages 15 thru 27)
or AMP PACE Connectors
(pages 98 thru 115)
97
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
ACTION PIN Press-Fit Contacts
The Reliable Plated Through-
Hole Interconnect
Solderless interconnections
have been popular in elec-
trical and electronic appli-
cation with world-wide
success for decades. They
provide reliable electrical
and mechanical stability
and offer applied-cost sav-
ings across the board. For
PC board applications,
ACTION PIN contacts from
Tyco Electronics provide
these features:
n Large gas-tight contact
zone
n Reliability due to stored
energy in compliant pin
contacts
n No damage to plated
through-holes during
installation
n Especially suited for mul-
tilayer PC boards
n Less costly board manu-
facturing due to larger
hole tolerances com-
pared to use of solid
pins
n Application can be
made by end-user
n Repairability—contact
can be replaced in the
same pin location (two
repairs)
n Installation with no heat
cycling of board
n Permits mass insertion
by minimizing forces
needed to insert pins as
compared to solid pin
press-fit application
n Significant applied-cost
savings in many applica-
tions
Since ACTION PIN contacts
do not have to be soldered,
issues associated with sol-
der are eliminated, such as:
• Faulty solder joints
• Solder fumes; cont-
aminant’s are
deposited on the
contacts
• Solder spots; short
circuits between
printed circuits
• Flux residuals
• Thermal strain on
printed circuit
boards and
components
• Degasing of plated
through-holes
Solderless press-fit inter-
connections using the
ACTION PIN contact are
primarily integrated in, but
not limited to, backplanes.
Solderless press-fit inter-
connections are used in
racks, especially where
connectors must be fixed
on the solder side of the PC
board and/or component
side. In these applications,
the holes for ACTION PIN
contact connectors are cov-
ered during the soldering
process and press-fitting is
performed after soldering.
Other applications for
ACTION PIN contact
interconnections include PC
boards that incorporate
components using surface
mount technology (SMT).
Here, too, press-fit intercon-
nections can be applied
after soldering, thus elimi-
nating complications
associated with connectors
suitable for surface
mounting.
Principle of the Tyco
Electronics Compliant
ACTION PIN Contact
When an ACTION PIN con-
tact is inserted into a plated
through-hole, two spring
members are compressed,
exerting force against the
hole for gas-tight connec-
tion. The diameter of the
hole is smaller than the
diagonal size of the pin
(see cross-section illustra-
tion below).
The beam characteristics of
the pin are designed so
that a plastic, as well as an
elastic, deformation takes
place during insertion. The
two spring members com-
press to different degrees
to accommodate hole toler-
ances. The compliant pin
also reduces strain on the
board. With a rigid pin, the
elastic strain energy is
stored entirely in the board,
leading to damage of the
plated through-holes. With
the ACTION PIN contact,
the residual force of the
elastic deformation main-
tains stored energy to pro-
duce a tight contact zone
between the pin and the
plated through-hole. This
provides long term electri-
cal and mechanical reliabili-
ty of the interconnection.
Cross-Section Area from Tyco Electronics ACTION PIN Press-Fit
Contact in Printed Circuit Board Holes from Tyco Electronics.
Note: ACTION PIN contact mounting hole specifications are presented in
each product section, where applicable.
Minimum
Hole Dia.
.037 [0.94]
Maximum
Hole Dia.
.043 [1.09]
98
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors
AMP PACE (Pre-Assembled
Card Edge) Connectors are
the latest innovation in the
evolution of backplane archi-
tecture. Designed to short-
en manufacturing time and
reduce applied costs, these
one-step, pre-assembled
connectors are ready for
mounting and mass inser-
tion. In addition, design
features such as removable
housings and contacts, that
are replaceable through the
top of the connector
housing, for maximum
flexibility in your backplane
packaging.
At the heart of the
AMP PACE Connector is
AMP’s proven and reliable
ACTION PIN Contact. This
unique contact has superior
electrical and physical
characteristics that are top
of the line in the industry.
AMP PACE Connectors are
available with post center-
line spacings of:
.100 x .100 [2.54 x 2.54]
.100 x .200 [2.54 x 5.08]
.125 x .125 [3.18 x 3.18]
.125 x .250 [3.18 x 6.35]
.156 x .200 [3.96 x 5.08]
Important:
Application tooling is
absolutely necessary to
insert connectors into PC
boards. See page 115 for
application tooling.
Performance Specifications
Electrical Characteristics
Contact Resistance: ACTION PIN
Contact Interface—5 milliohm
Spring Contact to Test Board—11.5
milliohms
Total Circuit Resistance:
12 milliohms
Continuous Current Rating*:
3 amperes
Insulation Resistance:
5,000 milliohms
Dielectric Withstanding Voltage:
.100 [2.54] Centerline Spacing—
1,000 VAC at sea level;
350 VAC at 50,000 ft. [15,240 m];
275 VAC at 70,000 ft. [21,336 m]
.125 [3.18] Centerline Spacing—
1,500 VAC at sea level;
500 VAC at 50,000 ft. [15,240 m];
235 VAC at 70,000 ft. [21,336 m]
Physical Characteristics
Card Insertion Force (Max.):
16 oz [4.45 N] per contact pair
ACTION PIN Contact Post
Card Extraction Force (Min.):
1 oz [.278 N] per contact pair
ACTION PIN Contact Post
Retention (in PC board):
.100 x .100 [2.54 x 2.54]—
7.5 lb. [33.4 N] min.
Operating Temperature:
–55°C to +85°C
Durability: Tested to 100 cycles (100
insertions and withdrawals at a rate not
exceeding 10 cycles per minute)
Salt Spray: MIL-STD-1344,
Method 1001
Physical Shock: MIL-STD-1344,
Method 2004
Thermal Shock: MIL-STD-1344,
Method 1003, Cond. A
Humidity: MIL-STD-1344,
Method 1002, Type II
Vibration: MIL-STD-1344,
Method 2005
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
Certified by
Canadian Standards
Association,
File No. LR7189
99
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors (Continued)
Product Facts
Repairability Details
Repairability—
(See below for details)
Individual contacts can be removed
without removing the housing;
housings can be removed without
removing posts. Important: APC board
must be inserted into the connector
when removing the contact.
Precision Plated Contacts—
Selective plating puts gold where
it is needed for superior electrical
contact at a reasonable cost.
Beam Contact Design
The contact’s unique beam design
accommodates and compensates
for daughter board warp and
stress providing long-term, reliable
performance (100 gram minimum
normal force).
Gas-Tight Connection—
Spring sections of ACTION PIN
Contacts compress in opposite
directions, maintaining a gas-tight
fit with the PC board.
Contact Tip Alignment Strip—
Polyester strip provides straight
and stable pin alignment for
damage-free entry into the
PC board. Precision Plated Post—
Gold plating can be applied to the
entire post, or just the post tip for
improved pluggability.
Remove and replace contacts
without removing housing.
(See page 115 for Contact
Replacement Tools.)
Remove and replace housing
without removing contacts.
100
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline
Standard Housing
Typical Closed End/
Open End Housings
Keying Plugs
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .475 [12.07]
Post Length
Connectors can be
mounted in pairs using
any size combinations.
Example:
1-30 pos. + 1-60 pos.
= 1-90 pos.
B
A
C±.006
[±0.15]
.100
[2.54]
.415
[10.54]
Card Slot
Depth
.380
[9.65]
.005/.007
[0.13/0.18]
See E Below
Post Length
and
Finish Area
.040
[1.02] Min.
Contact Finish Area
.025
[0.64] Sq.
Post
.100
[2.54]
.100
[2.54]
.135
[3.43]
Detail E
Intercontact (Plastic)
Part No. 118982-1 On-Contact (Plastic)
Part No. 119802-2
.100
[2.54]
101
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. nickel in
contact area, .000100 [0.00254] min.
tin-lead on posts, with entire contact
underplated .000050 [0.00127] min.
nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-2978,
408-2979, 408-6881, 408-9091,
408-9188
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
No. of Dimensions Post Closed/Closed Closed/Open
Dual
Positions ABCLength Standard Scoop Standard
.180
1.400 1.734 1.604 4.57 119734-1 119736-1
15 35.56 44.04 40.74 .475
12.07 119237-1
1.900 2.234 2.104 .180
20 48.26 56.74 53.44 4.57 119734-6
2.400 2.734 2.604 .180
25 60.96 69.44 66.14 4.57 1-119734-1
2.700 3.034 2.904 .180
28 68.58 77.06 73.76 4.57 1-119734-4
3.000 3.334 3.204 .475
31 76.20 84.68 81.38 12.07 1-119237-7
.180
3.400 3.734 3.604 4.57 2-119734-1 119831-6
35 83.36 94.84 91.54 .475
12.07 119413-6
3.900 4.234 4.104 .180
40 99.06 107.54 104.24 4.57 2-119734-6 2-119736-6
4.700 5.034 4.904 .475
48 119.38 127.86 124.56 12.07 3-119237-4
4.900 5.234 5.104 .180
50 124.46 132.94 129.64 4.57 3-119734-6
5.900 6.234 6.104 .180
60 149.86 158.34 155.04 4.57 4-119734-6 4-119736-6
Note: Other connector sizes and connectors with card scoops can be made available, consult Tyco Electronics.
102
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline
Standard Housing
Housing with High Card
Scoops
Keying Plugs
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .475 [12.07]
and .702 [17.83]
Post Lengths
B
A
C±.006
[±0.15]
.100
[2.54]
.415
[10.54]
Card Slot
Depth
.360
[9.14]
.005/.007
[0.13/0.18]
See E Below
Post Length
and
Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.545
[13.84]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.200
[5.08]
.515
[13.08]
Card Slot
Depth
.390
[9.91]
.005/.007
[0.13/0.18]
See E Below
Post Length
and
Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.645
[16.38]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.200
[5.08]
.135
[3.43]
.100
[2.54]
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .475 [12.07]
and .702 [17.83]
Post Lengths
Detail E On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
B
A
C±.006
[±0.15]
.100
[2.54]
.100
[2.54]
103
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. nickel in
contact area, .000100 [0.00254] min.
tin-lead on posts, with entire contact
underplated .000050 [0.00127] min.
nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-2933,
408-2978, 408-2979, 408-9058,
408-9067, 408-9091, 408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
No. of Dimensions Post Closed End/Closed End
Dual
Positions ABCLength Standard High Scoop
.900 1.234 1.104 .180
10 22.86 31.34 28.04 4.57 1-650297-1
1.400 1.734 1.604 .180
15 35.56 44.04 40.74 4.57 1-119738-1 119791-1
1.700 2.034 1.904 .180
18 43.18 51.66 48.36 4.57 1-119738-4
1.900 2.234 2.104 .180
20 48.26 56.74 53.44 4.57 1-119738-6
.180
2.100 2.434 2.304 4.57 1-119738-8
22 53.34 61.82 58.52 .475
112.07 -119216-8 650123-8
2.300 2.634 2.504 .180
24 58.42 66.90 63.60 4.57 1-119738-0
.180
2.400 2.734 2.604 4.57 1-119738-1
25 60.96 69.44 66.14 .702
17.83 1-119163-1
.180
2.700 3.034 2.904 4.57 1-119738-4
28 68.58 77.06 73.76 .475
12.07 1-119216-4
.180
4.57 1-119738-6 1-119791-6
2.900 3.234 3.104 .475
30 73.66 82.14 78.84 12.07 1-119216-6
.702
17.83 1-119163-6
3.000 3.334 3.204 .180
31 76.20 84.68 81.38 4.57 1-119738-7
3.100 3.434 3.304 .180
32 78.74 87.22 83.92 4.57 1-650122-8
.180
34 3.300 3.634 3.504 4.57 2-119791-0
83.82 92.30 88.90 .475
12.06 2-119216-0
3.400 3.734 3.604 .475
35 86.36 94.84 91.54 12.06 2-119216-1
.180
3.500 3.834 3.704 4.57 2-119738-2
36 88.90 97.38 94.08 .475
12.06 2-119216-2
3.600 3.934 3.804 .180
37 91.44 99.92 96.62 4.57 2-650122-3
.180
3.900 4.234 4.104 4.57 2-119738-6
40 99.06 107.54 104.24 .475
12.06 2-119216-6
4.200 4.534 4.404 .180
43 106.68 115.16 111.86 4.57 2-650122-9
4.300 4.634 4.504 .475
44 109.22 117.70 114.40 12.07 3-119216-0
.180
4.57 3-119738-6 3-119791-6
4.900 5.234 5.104 .475
50 124.46 132.94 129.64 12.07 3-119216-6
.702
17.83 3-119726-6
5.400 5.734 5.604 .180
55 137.16 145.54 142.34 4.57 4-119738-1 4-650124-1
.180
5.900 6.234 6.104 4.57 4-119738-6
60 149.86 158.34 155.04 .702
17.83 119677-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
104
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connectors, .125 x .125 [3.18 x 3.18] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. palladium-
nickel in contact area, .000100
[0.00254] min. tin-lead on posts, with
entire contact underplated .000050
[0.00127] min. nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-6727,
408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
Housing with High Card
Scoops
28 Dual Positions
Part Number 1-119853-4
Keying Plugs
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
and .702 [17.83]
Post Length
.125
[3.18]
3.755
[95.38]
3.625±.006
[92.08±0.15]
3.375
[85.72]
.125
[3.18]
.515
[13.08]
Card Slot
Depth
.420
[10.67]
.005/.007
[0.13/0.18]
See E Below
.702
[17.83]
Post Length
and Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.025
[0.64] Sq.
Post
.125
[3.18]
.135
[3.43]
Detail E
On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
105
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
AMP PACE Connector Specials, .125 x .125 [3.18 x 3.18] Centerline
27 Dual Positions
Tin-Lead Posts
.634 [16.10] Long
Part No. 645394-1
18 or 36
Dual Positions
Tin-Lead Posts
.740 [18.80] Long
Part No. 119552-2
Tin-Lead Posts
.180 [4.57] Long
Part No. 119880-1
97 Dual Positions
(Two-piece Closed
End/Open End with Partial
Card Scoops and Card
Guides)
Contact Tyco Electronics for
specific Part Number infor-
mation.
106
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline
Standard Housing
Housing with High Card
Scoops
Typical Closed End/
Open End Housings
Keying Plugs
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .500 [12.07]
and .702 [17.83]
Post Lengths
B
A
C±.006
[±0.15]
.125
[3.18]
.415
[10.54]
Card Slot
Depth
.410
[10.41]
.005/.007
[0.13/0.18]
See E Below
.702
[17.83]
Post Length
and Finish Area
.702
[17.83]
Post Length
and Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.545
[13.84]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.250
[6.35]
.515
[13.08]
Card Slot
Depth
.420
[10.67]
.005/.007
[0.13/0.18]
See E Below
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.645
[16.38]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.250
[6.35]
.135
[3.43]
.125
[3.18]
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .500 [12.07]
and .702 [17.83]
Post Lengths
Detail E On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
B
C±.006
[±0.15]
.125
[3.18]
.125
[3.18]
3.375
[85.72]
Connectors can be
mounted in pairs using
any size combinations.
Example:
1-30 pos. + 1-60 pos.
= 1-90 pos.
.125
[3.18]
Card Edge Connectors
(Press-Fit Board-To-Board)
107
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. nickel in
contact area, .000100 [0.00254] min.
tin-lead on posts, with entire contact
underplated .000050 [0.00127] min.
nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-2933,
408-2978, 408-2979, 408-9063,
408-9091, 408-9119, 408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
No. of Dimensions Post Closed End/Closed End Closed End/Open End
Dual
Positions A B C Length Standard High Scoop High Scoop
2.125 2.373 2.505 .180
18 53.98 60.27 63.63 4.57 1-119822-4 3-119840-2
.180
4.57 1-119822-8
2.625 3.005 2.875 .500
22 66.68 76.33 73.02 12.70 1-119200-8
.702
17.83 1-119202-8
3.000 3.380 3.250 .180
25 76.20 85.85 82.55 4.57 1-119822-1
3.250 3.630 3.500 .702
27 82.55 92.20 88.90 17.83 1-119202-3
.180
3.375 3.755 3.625 4.57 1-119822-4
28 85.72 95.38 92.08 .500
12.70 1-119200-4
.180
3.625 4.005 3.875 4.57 1-119822-6 1-678034-1
30 92.08 101.73 98.24 .500
12.70 1-119841-6
.180
4.375 4.755 4.625 4.57 2-119822-2 1-678034-2
36 111.82 120.78 117.48 .500
12.70 2-119841-2
4.625 4.873 5.005 .180
38 117.47 123.77 127.13 4.57 2-119822-4 3-119840-9
.180
4.875 5.255 5.125 4.57 2-119822-6
40 123.83 133.48 130.18 .702
17.83 2-119200-6
6.125 6.505 6.375 .180
50 155.58 165.23 161.93 4.57 3-119822-6
6.250 6.630 6.500 .500
51 158.75 168.40 165.10 12.70 3-119200-7
7.375 7.755 7.625 .180
60 187.33 196.98 193.68 4.57 4-119822-6
Note: Other connector sizes can be made available, consult Tyco Electronics.
108
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make
Before Break Contacts
Standard Housing
Housing with High Card
Scoops
Typical Closed End/
Open End Housings
Keying Plugs
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .500 [12.07]
and .702 [17.83]
Post Lengths
B
A
C±.006
[±0.15]
.125
[3.18]
.415
[10.54]
Card Slot
Depth
.410
[10.41]
.005/.007
[0.13/0.18]
See E Below
.702
[17.83]
Post Length
and Finish Area
.702
[17.83]
Post Length
and Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.545
[13.84]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.250
[6.35]
.515
[13.08]
Card Slot
Depth
.420
[10.67]
.005/.007
[0.13/0.18]
See E Below
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.645
[16.38]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.250
[6.35]
.135
[3.43]
.125
[3.18]
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
Contact Tip
Alignment Strip
on .500 [12.07]
and .702 [17.83]
Post Lengths
Detail E On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
B
C±.006
[±0.15]
.125
[3.18]
.125
[3.18]
3.375
[85.72]
Connectors can be
mounted in pairs using
any size combinations.
Example:
1-30 pos. + 1-60 pos.
= 1-90 pos.
.125
[3.18]
109
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors, .125 x .250 [3.18 x 6.35] Centerline w/ Make
Before Break Contacts (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. nickel in
contact area, .000100 [0.00254] min.
tin-lead on posts, with entire contact
underplated .000050 [0.00127] min.
nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-2933,
408-2978, 408-2979, 408-9063,
408-9091, 408-9119, 408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
No. of Dimensions Post Closed End/Closed End Closed End/Open End
Dual
Positions A B C Length Standard High Scoop
2.125 2.505 2.373 .180
18 53.98 63.63 60.27 4.57 1-1571235-1
2.875 3.123 3.058 .180
24 76.20 79.25 77.67 4.57 650059-2
Note: Other connector sizes can be made available, consult Tyco Electronics.
110
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold .000030 [0.00076] min. thk. over
.000050 [0.00127] min. thk. nickel in
contact area, .000100 [0.00254] min.
tin-lead on posts, with entire contact
underplated .000050 [0.00127] min.
nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-6726,
408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
Standard Housing
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards Contact Tip
Alignment Strip
on .475 [12.07]
and .702 [17.83]
Post Lengths
B
A
C±.006
[±0.15]
.156
[3.96]
.156
[3.96]
.415
[10.54]
Card Slot
Depth
.360
[9.14]
.005/.007
[0.13/0.18]
See E Below
Post Length
and
Finish Area
.040
[1.02] Min.
Contact
Finish Area
.364
[9.24]
.545
[13.84]
.025
[0.64] Sq.
Post .093
[2.36] Min.
.200
[5.08]
Keying Plugs
.135
[3.43] Detail E
On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
No. of Dimensions Post Closed End/Closed End
Dual
Positions A B C Length Standard
.180
4.57 1-119790-1
2.184 2.626 2.495 .475
15 55.47 66.70 63.39 12.07 1-119254-1
.702
17.83 1-119256-1
2.652 3.094 2.964 .475
18 67.36 78.59 75.29 12.07 1-119254-4
.180
4.57 1-119790-8
3.276 3.718 3.588 .475
22 83.21 94.44 91.13 12.07 1-119254-8
.702
17.83 1-119256-8
.180
4.57 1-119790-4
4.212 4.654 4.524 .475
28 106.98 118.21 114.91 12.07 1-119254-4
.702
17.83 1-119256-4
.180
4.57 2-119790-9
6.552 6.994 6.864 .475
43 166.42 177.65 174.35 12.07 2-119254-9
.702
17.83 2-119256-9
Note: Other connector sizes can be made available, consult Tyco Electronics.
111
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors, .156 x .200 [3.96 x 5.08] Centerline w/Make
Before Break Contacts
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
gold flash over .000030 [0.00076] min.
thk. over .000050 [0.00127] min. thk.
nickel in contact area, .000100
[0.00254] min. tin-lead on posts, with
entire contact underplated .000050
[0.00127] min. nickel
Contact Tip Alignment Strip—Clear
polyester, type D
Related Product Data:
Performance Specifications
page 98
Accessories—page 112
PC Board Edge Pattern—page 113
ACTION PIN Contact Mounting
Hole Specifications—page 114
Application Tooling—page 115
Contact Replacement Tools
page 115
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14019, 108-26003
Application Specification
114-26002
Instruction Sheets 408-6726,
408-9186
Note: Full palladium-nickel plated
posts and other platings and plating
thicknesses can be made available.
Card Scoop Housing
.228
[5.78]
.364
[9.25]
.005/.007
[0.13/0.18] .200
[5.08]
.116
[2.95] Contact Area
.093
[2.36] Min.
.045
[1.14] Contact Area
Keying Plugs
.135
[3.43]
Detail E
On-Contact (Plastic)
Part No. 119802-2
Intercontact (Plastic)
Part No. 118982-1
No. of Dimensions Post Closed End/Closed End
Dual
Positions A B C Length Scoop
2.652 3.094 2.964 .180
18 67.36 78.59 75.29 4.57 678035-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
C
B
A
Accepts
.054 to .071
[1.37 to 1.80]
PC Boards
.156
[3.96]
.156
[3.96]
112
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Accessories for AMP PACE Connectors
Material: Black glass-filled polyester
Related Product Data:
Mates with all standard housings (will
not mate with some special housings)
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-9091
Connector Card Guide
Rating:
20 amperes per contact—Copper or
aluminum bus
Material and Finish:
Housing—Black glass-reinforced
thermoplastic
Contact—CA 195, 3/4 hard, plated
.000050 [0.00127] gold in contact area
(front face only); .000100 [0.00254] tin-
lead on post, with entire contact under-
plated .000050 [0.00127] nickel
Related Product Data:
Mates with all standard housings (will
not mate with some special housings)
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-2978
Ground Module
L1Part Numbers
2.500
63.50 1-117169-3
6.000
152.40 1-117169-3
1Other lengths up to 6.0 [152.4] can be
made available. Consult Tyco
E l e c t r o n i c s for details.
BDimension from
AMPPACEConnector
Tables Plus .310 [7.87]
Hole for
#4 Self-Tapping
Screw
(mandatory)
.050 [12.7] Deep
Accepts
.054 to.071
[1.37 to 1.80]
PC Board
L
.410
[10.41] .220
[5.59]
.420
[10.67]
.455
[11.56]
.250
[6.35]
.300
[7.62]
.700
[17.78]
.370
[9.4]
.060
[1.52]
Contact
Area
Part No. 119341-1
Seating Tool 59881-1
.152
[3.96] Dia.
(2 Holes)
113
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
PC Board Layout for AMP PACE Connectors
Recommended
PC Board Edge Pattern
.430
[10.92]
Gold
Fingers
.050
[1.27]
Max. Chamfer
.275
[6.99]
.052±.002
[1.32±0.05]
Key Slot
B
A1
C±.005
[±0.13]
.040 +.020
-.010
[1.016+.508
-.254 ]
30°
.054-.071
[1.37-1.80]
1A Max. = Minimum connector card slot -.001 [-0.03].
A Min. = Minimum connector card slot -.011 [-0.28].
Note: Finger pattern to be centered on daughter card.
Each finger can deviate .003 [0.08] from true position.
AMP PACE Connector Dimensions
Centerline Spacing B C
.100 x .100 .100 .070
2.54 x 2.54 2.54 1.78
.100 x .200 .100 .070
2.54 x 5.08 2.54 1.78
.125 x .125 .125 .080
3.18 x 3.18 3.18 2.03
.125 x .250 .125 .080
3.18 x 6.35 3.18 2.03
.156 x .200 .156 .080
3.96 x 5.08 3.96 2.03
114
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
AMP PACE Connectors (Continued)
AMP ACTION PIN
Press-Fit Contacts
ACTION PIN contacts provide a reliable press-fit connection.
Localized pressure in the interface area entails oxide
break-through and helps prevent corrosion in the harshest
environments to provide a reliable connection virtually every
time. Also, radial and axial distortion are controlled to meet
today’s standards for multilayer board applications.
PC Board Thickness
ACTION PIN contacts are
designed for use in a variety of
PC board thicknesses. However,
certain ACTION PIN contacts
are to be used in specific
ranges of board thicknesses. To
promote optimum performance,
the recommended board thick-
nesses provided with the con-
nector being used must be
followed. Annular Ring (See Note)
Drilled Hole
Copper Thickness
Tin-Lead Thickness
Plated Through-Hole
Mounting Hole Specifications
Connector ACTION PIN Contact Drilled Hole Plating Thicknesses Plated Radial Hole Distortion
No. of Dual Material Through-Hole
Centerline Positions Thickness DiameterCopper* Tin-LeadDiameterAverage Maximum
.125 x .125
3.18 x 3.18 28, 97 .025 .0453±.001 .001-.003 .0003 .037-.043 Not Not
.156 x .200 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 Specified Specified
3.96 x 5.08 15-43 Min.
.125 x .125 .025 .0465±.001 .001-.003 .0003 .037-.043 Not Not
27 0.008
3.18 x 3.18 0.64 1.181±0.03 0.03-0.08 Min. 0.94-1.09 Specified Specified
.100 x .100
2.54 x 2.54 15-60
.100 x .200
2.54 x 5.08 15-60 .025 .0453±.001 .001-.003 .0003 .037-.043 .0015 .002
.125 x .125 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 0.038 0.05
3.18 x 3.18 18, 36 Min.
.125 x .250
3.18 x 6.35 18-60
*Maximum hardness of copper layer is 150 Knoop.
Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].
115
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Application Tooling for AMP PACE Connectors
Modular Seating Tools
Available from Tyco
Electronics is
a complete series of
AMP PACE Modular
Seating Tools for installing
AMP PACE Connectors on
printed circuit boards and
panels. These tools are
modular in design in that
housing tool holders may
be added or subtracted to
accommodate several dif-
ferent connector sizes. In
addition, all tool parts are
individually replaceable
should the tool become
damaged.
Modular seating tools are
supplied in two basic
designs: One which covers
all connector centerlines
except .100 x .100 [2.54 x
2.54] and one for the .100 x
.100 [2.54 x 2.54] centerline
connectors.
All seating tools have a
common shut height of
1.5 inches [38]. This
allows AMP PACE and other
ACTION PIN products to be
seated at the same time on
AMP seating machines. See
page 149 for a description
of the AMP seating
machines.
.100 x .100 [2.54 x 2.54]
Centerline Spacing .100 x .200 [2.54 x 5.08], .156 x .200 [3.96 x 5.08]
.125 x .125 [3.18 x 3.18], Centerline Spacing
.125 x .250 [3.18 x 6.35],
No. of Centerline
Dual .100 x .100 .100 x .200 .125 x .250 .156 x .200
Positions [2.54 x 2.54] [2.54 x 5.08] [3.18 x 6.35] [3.96 x 5.08]
15 1-58200-1 1-58140-1 1-58143-1
18 1-58140-4 1-58142-4
20 1-58200-6 1-58140-6
22 1-58140-8 1-58142-8 1-58143-8
25 1-58200-1 1-58140-1 1-58142-1
28 1-58200-4 1-58140-4 1-58142-4 1-58143-4
30 1-58200-6 1-58140-6 1-58142-6
31 1-58200-7
32 1-58140-8
34 2-58140-0
35 2-58200-1 2-58140-1
36 2-58140-2 2-58142-2
37 2-58140-3
40 2-58200-6 2-58140-6 2-58142-6
43 2-58140-9 2-58143-9
44 3-58140-0
48 3-58200-4
50 3-58200-6 3-58140-6 3-58142-6
51 3-58200-7 3-58142-7
54 4-58200-0
55 4-58200-1 4-58140-1
56 4-58142-2
60 4-58200-6 4-58140-6 4-58142-6
For Connectors without Scoops
For Connectors with Scoops
No. of Centerline
Dual .100 x .200 .125 x .125 .125 x .250
Positions [2.54 x 5.08] [3.18 x 3.18] [3.18 x 6.35]
15 1-58150-1
18 1-58184-4
22 1-58150-8
28 1-58218-4
30 1-58150-6
38 2-58184-4
50 3-58150-6 3-58184-6
55 4-58150-1
Contact Replacement
Tools
Replacement tools listed in
the chart at the right are
used to install replacement
contacts in AMP PACE con-
nector housings. Replace-
ment Tool 1-265871-7 is
used to remove all .025
[0.64] square posts from
PC boards.
Housing Style
Centerline Standard Full Card Scoop
.100 x .100
2.54 x 2.54 266220-3
.100 x .200
2.54 x 5.08 266220-1 58210-1
.125 x .125
3.18 x 3.18 58210-4
.125 x .250
3.18 x 6.35 266220-2 58210-2
.156 x .200
3.96 x 5.08 266220-2
Note: Tooling availability is
dependent upon part number
activity. Consult Tyco
Electronics for further
information.
116
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
TELEDENSITY Connectors
Product Facts
High density - .0625 [1.586]
contact centerlines
Compliant ACTION PIN
contacts press-fit into
plated-through holes for
solderless application
Individually replaceable
contacts
Accommodates up to three
levels of daughter card pads
for sequencing
.125 [3.18] square grid post
arrangement
The high performance AMP
TELEDENSITY connector is
a high density, card edge,
telecommunications con-
nector. It features compliant
ACTION PIN contacts for
solderless application to
multi-layer printed circuit
boards with plated-through
or bare copper holes.
These connectors accept
.054 to .072 [1.37 to 1.83]
thick daughter cards. To
satisfy the broadest range
of application needs, the
contacts are plated with 30
microinches of gold in the
mating area and tin-lead on
the posts. A plastic locating
strip keeps posts positioned
correctly for board insertion.
For high-density needs,
TELEDENSITY connectors
offer a .0625 [1.586] daugh-
ter card contact centerline
spacing in 39-, 71-, or 99-
dual positions. The connec-
tor’s .330 [8.38] slot depth
accommodates up to three
levels of daughter card
pads for sequencing, while
a biasing wedge maintains
proper pad alignment dur-
ing card extraction. Posts
are arranged in a .125
[3.18] square grid to ease
circuit routing.
Performance Specifications
Current Rating*:
3 amperes max.
Mating Force (Contact Pair):
1 lb. [4.4 N] max.
Durability (Mating Cycles):
100 min.
Termination Resistance:
12 milliohms max.
Dielectric Rating:
1200 VAC (rms)
Insulation Resistance:
5000 megohms max.
Operating Temperature:
–55°C to +85°C
*Consult Tyco Electronics
when paralleling contacts
for power applications.
117
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Material and Finish:
Housing—Black polyester
Contacts—Copper alloy 725, plated
.000030 [0.00076] gold in contact area,
.000030 [0.00076] solder plate on post,
with entire contact underplated .000100
[0.00254] nickel
Coil Spring—Stainless steel
Contact Tip Alignment Strip—Clear
polyester
Related Product Data:
Performance Specifications
page 116
ACTION PIN Contact Mounting
Hole Specifications—page 118
Technical Document—pages 186,
187
Product Specification
108-26003
Instruction Sheet
408 6866
TELEDENSITY Connectors, .0625 [1.586] Centerline
Recommended
PC Board Layout
(Shown from post side)
Number of Dimensions Connector Seating
Dual Part Tool
Positions A B C D Numbers Numbers**
.634 650148-1
39 3.168 2.588-2.600 16.10 2.375 58084-1
80.47 65.74-66.04 .350 60.33 650281-1*
8.89
71 5.168 4.588-4.600 .634 4.375 650149-1 58084-3
131.27 116.54-116.84 16.10 111.13
99 6.918 6.338-6.350 .634 6.125 650150-1 58084-2
175.72 160.99-161.29 16.10 155.58
* Contacts in this connector are underplated .000150 [0.00381] nickel.
** See page 149 for a description of AMP seating machines.
Note: ACTION PIN posts require .093 [2.36] min. thick PC board.
For mounting hole specifications, see page 123
118
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
TELEDENSITY Connectors (Continued)
AMP ACTION PIN
Press-Fit Contacts
ACTION PIN contacts provide a reliable press-fit connection.
Localized pressure in the interface area entails oxide
breakthrough and helps prevent corrosion in the harshest
environments to provide a reliable connection virtually every
time. Also, radial and axial distortion are controlled to meet
today’s standards for multilayer board applications.
PC Board Thickness
ACTION PIN contacts are
designed for use in a variety of
PC board thicknesses. However,
certain ACTION PIN contacts
are to be used in specific ranges
of board thicknesses. To
promote optimum performance,
the recommended board thick-
nesses provided with the con-
nector being used must be
followed.
Annular Ring (See Note)
Drilled Hole
Copper Thickness
Tin-Lead Thickness
Plated Through-Hole
Mounting Hole Specifications
ACTION PIN Drilled Hole Plating Thicknesses P l a t e d - T h r o u g h Radial Hole Distortion
C o n t a c t D i a m e t e r
C o p p e r
*T i n - L e a d
H o l e A v e r a g e M a x i m u m
Material Thickness D i a m e t e r
. 0 2 5 . 0 4 5 3 ± . 0 0 1 . 0 0 1 - . 0 0 3 .0003 M i n . . 0 3 7 - . 0 4 3 . 0 0 1 5 . 0 0 2
0 . 6 4 1 . 1 5 1 ± 0 . 0 3 0 . 0 3 - 0 . 0 8 0 . 0 0 8 0 . 9 4 - 1 . 0 9 0 . 0 3 8 0 . 0 5
*Maximum hardness of copper layer is 150 Knoop
N o t e : Recommended annular ring diameter is hole diameter plus . 0 2 0 [ 0 . 5 1 ]
119
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Connectors
AMP ECONOMATE
Connectors provide a
reliable and economical
method for interconnecting
backplane panels, using
either two-sided or multi-
layer PC boards.
Connector housings are fur-
nished unloaded and are
available for post centerline
spacings of: .100 x .200
[2.54 x 5.08] and .156 x .200
[3.96 x 5.08]. The housings
are simply positioned onto
the contacts, after the con-
tacts have been inserted
into the PC board and the
carrier strip removed.
Contacts from Tyco
Electronics feature the
proven and reliable
ACTION PIN contact
design.These press-fit con-
tacts employ two spring
members that compress to
exert force against the
plated through-holes for a
gas-tight connection.
Gold plating of contacts
promotes the electrical
integrity of the connection.
Feed-through posts are also
available for accepting
wrap-type terminations.
These posts also feature the
ACTION PIN contact design
and are supplied in strip
form and stored on reels for
insertion into PC boards.
Performance Specifications
Electrical Characteristics
Contact Resistance:
8 milliohms (max.)
Insulation Resistance:
2,000 megohms (min.)
Continuous Current Rating*:
3 amperes
Physical Characteristics
Card Insertion Force:
16 oz [4.45 N] (max.) per contact pair
Card Extraction Force:
1 oz [0.28 N] (min.) per contact pair
Retention (in PC Board):
7 lb [31.1 N] (min.)
Operating Temperature:
–65°C to +125°C
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Important:
Application tooling is
absolutely necessary for
installing contacts and
housings onto PC boards.
See page 126 for applica-
tion tooling.
120
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Connectors (Continued)
.100 x .200 [2.54 x 5.08]
Centerline Spacing
Material and Finish:
Housing—Black glass-filled nylon
Contacts—Copper alloy 725, plated as
follows:
Plating A—Selectively plated .000030
[0.00076] min. gold in contact area,
.000001 [0.00003] min. gold on remain-
der of contact, with entire contact under-
plated .000050 [0.00127] min. nickel
Plating B—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on
posts, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Selectively plated .000100
[0.00254] min. gold in contact area,
.000001 [0.00003] min. gold on remain-
der of contact, except .000050 [0.00127]
min. gold for .200 [5.08] from tip of
post, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications
page 119
Card Guides—page 122
ACTION PIN Contact Mounting
Hole Specifications—page 125
Application Tooling—page 126
Technical Documents:
(pages 186, 187):
Product Specification
108-26002
Keying Plugs
Intercontact (Plastic)
Part No. 118982-1
Make-Before-Break Contacts
On-Contact (Plastic)
Part No. 119802-2
No. of Dimensions Housing
Dual Part
Positions A B Numbers
2.734 2.604
25 82.14 78.84 1-117798-4
3.234 3.104
30 82.14 78.84 1-117798-3
3.734 3.604
35 94.84 91.54 1-117798-6
3.834 3.704
36 97.38 94.08 1-117798-7
4.234 4.104
40 107.54 104.24 1-117798-8
5.234 5.104
50 132.94 129.64 1-117798-1
6.234 6.104
60 158.34 155.04 1-117798-2
Note: Other connector sizes can be made available,
consult Tyco Electronics.
. 1 0 0
[ 2 . 5 4 ]
A
B
(Card Slot
Length)
Accepts
.054-.071
[1.37-1.80]
PC Boards
Contact
Area
.025
[0.64] Sq.
.100
[2.54]
.025
[0.64] Sq.
.040
[1.02] Ref.
Gold in
Contact
Area
.100
[2.54]
.181
[4.60]
.415
[10.54] .545
[13.84]
.093-.125
[2.36-3.18]
L
.200
[5.08]
Dimension Contact Part Numbers*
LPlating A Plating B Plating C
.475
12.07 2-117795-4 4-117795-0
.702
17.83 1-117795-3 2-117795-6 4-117795-8
*Contacts are strip form, 35,000 per reel.
Dimension Make Before Break Contact Part Numbers*
LPlating A Plating B
.475
12.07 4-118951-8
.702
17.83 1-118951-4
121
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Connectors (Continued)
Keying Plug
Intercontact (Plastic)
Part No. 118982-1
.156 x .200 [3.96 x 5.08]
Centerline Spacing
Material and Finish:
Housing—Black glass-filled nylon
Contacts—Copper alloy 725, plated as
follows:
Plating A—Selectively plated .000030
[0.00076] min. gold in contact area,
.000001 [0.00003] min. gold on remain-
der of contact, with entire contact under-
plated .000050 [0.00127] min. nickel
Plating B—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on
posts, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications
page 119
Card Guides—page 122
ACTION PIN Contact Mounting
Hole Specifications—page 125
Application Tooling—page 126
Technical Documents:
(pages 186, 187):
Product Specification
108-26002
Note: Other connector sizes can be made available,
consult Tyco Electronics.
*Contacts are strip form, 15,000 per reel.
22 Dual Position Housing
Part No. 117296-4
Make-Before-Break Contacts
. 1 5 6
[ 3 . 9 6 ]
3.718
[94.44]
3.588
[91.14]
(Card Slot
Length)
Accepts
.054-.071
[1.37-1.80]
PC Boards
Contact
Area
.025
[0.64] Sq.
.156
[3.96]
.181
[4.60]
.415
[10.54] .545
[13.84]
.093-.125
[2.36-3.18]
L
.200
[5.08]
Dimension Contact
L Part Numbers*
.475
12.07 117285-7
.702
17.83 117285-8
Make Before Break Contacts
Dimension Plating Part
L Numbers*
.475 B
12.07 1-118778-2
.702 A
17.83 118778-6
.025
[0.64] Sq.
.150
[3.01] Ref.
Gold in
Contact
Area
.150
[3.06]
.702
[17.83]
122
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Card Guides for ECONOMATE Connectors
Material: Black glass-filled nylon
Recommended Mounting Dimensions
Note: A1dimension = Adimension of
ECONOMATE housing plus .310 [7.87].
L
Hole for
No. 4 Screw
0.45
[11.43] deep .220
[5.59]
.410
[10.41]
.152
[3.86] Dia.
(2 Plcs.)
A1
*Other lengths can be made avail-
able in .500 [12.70] increments
from 1.500 [38.10] to 6.500
[165.10]. Consult Tyco Electronics
for details.
Dimension Card Guide
L* Part Numbers
2.500
63.50 1-117169-3
6.000
152.40 1-117169-3
Housing Dimension
Centerline No. of Dual
Spacing Positions A1
3.544
30 90.02
4.044
35 102.72
4.144
.100 x .200 36 105.26
2.54 x 5.08 4.544
40 115.42
5.544
50 140.82
6.544
60 166.22
.156 x .200 4.028
3.96 x 5.08 22 102.31
Related Product Data:
Mates with all .100 x .200 [2.54 x 5.08]
and .156 x .200 [3.96 x 5.08] centerline
housings
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-9091
123
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Center Carrier Feed-Thru Posts*
.125 [3.18] Centerline,
Wrap Type
Material:
Copper Alloy 725
Finish – Gold plate per MIL-G-45204 or
solder plate over nickel plate per
QQ-N-290 (see table for thicknesses)
Recommended Hole Size:
Non Plated-thru Hole - .0453±.001
[1.15±0.03], 1.15 mm drill
Plated-Thru Hole -.039±.004 [0.99± 0.1 ],
1.15 mm drill
Dimensions Part Numbers
.000100 [0.0025] min. .000030 [0.00076]
A B tin plate over gold plate over
.000050 [0.0013] min. .000050 [0.0013]
nickel plate nickel plate
.703 .548 117311-7 1-117311-0
17.68 13.92
*Use AMP Cut and Transfer Machine for center carrier post insertion. Consult
Tyco Electronics.
D i m e n s i o n s Part Numbers
1) .000001 [0.00003] min.
gold flash over
.000050 [0.0013] min.
A B C nickel plate
2) .000050 [0.0013] min.
gold plate over
.000050 [0.0013] min.
nickel plate
. 3 1 8 . 6 8 7 1 . 0 0 5
8 . 0 8 1 7 . 4 5 2 5 . 5 3
. 5 7 8 . 4 6 0 1 . 0 3 8 1 1 8 2 4 3 - 8
1 4 . 6 8 1 1 . 6 8 2 6 . 3 7
. 5 7 8 . 5 5 0 1 . 1 2 8 1 - 1 1 8 2 4 3 - 1
1 4 . 6 8 1 3 . 9 7 2 8 . 6 5
. 3 8 0 . 8 2 3 1 . 2 0 3
9 . 6 5 2 0 . 9 0 3 0 . 5 6
.100 [2.54] Centerline,
TERMI-POINT Clip Part
Number 119136-2
Material:
Copper Alloy 725
Finish
1) Gold plate per MIL-G-45204, .000030
[0.00076] min. thk. over nickel plate per
QQ-N-290, .000050 [0.0013] min. thk.
2) Gold flash per MIL-G-45204, .000001
[0.00003] min. thk. over nickel plate per
QQ-N-290, .000050 [0.0013] min. thk.
Recommended Hole Size:
Non Plated-thru Hole - .0453±.001
[1.15±0.03], 1.15 mm drill
Plated-thru Hole - .039±.004 [0.99± 0.1 ],
1.15 mm drill
.100 [2.54] Centerline,
Wrap Type
Material:
Copper Alloy 725
Finish – Gold plate per MIL-G-45204
over nickel plate per QQ-N-290 (see table
for thicknesses)
Recommended Hole Size:
Non-Plated-thru Hole - .0453±.001
[1.15±0.03], 1.15 mm drill
Plated-thru Hole- .039 ±.004 [0.99 ± 0.1 ],
1.15 mm drill .003
.003
.003
0.08
0.08
0.08
124
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Connectors (Continued)
50,000 per reel
Part No. 117269-5
Feed-Through Posts .100 [2.54] Centerline Spacing
Material and Finish:
Copper alloy 725, plated as follows:
Plating A—Selectively plated .000030
[0.00076] min. gold in Area (1), .000001
[0.00003] min. gold in Area (2), with
entire post underplated .000050
[0.00127] min. nickel
Plating B—.000030 [0.00076] min.
gold over .000100 [0.00254] min. nickel
on entire post
Plating C—.000050 [0.00127] min.
gold over .000100 [0.00254] min. nickel
on entire post
Plating D—.000100 [0.00254] min.
tin-lead over .000050 [0.00127] min.
nickel on entire post
.150 [3.81] Centerline Spacing
Material and Finish:
Copper alloy 725, selectively plated
.000030 [0.00076] min. gold in Area (1),
.000001 [0.00003] min. gold in Area (2),
with entire post underplated .000050
[0.00127] min. nickel
Dimension Feed-Through Post Part Numbers*
APlating A Plating B Plating C Plating D
.687 1-117249-7
17.45 13-117249-111-117249-2 1-117249-2 6-117249-5
.500
12.70 3-117249-2 5-117249-6
*Posts in strip form, 50,000 per reel.
1Pre-notched to break with 120° bend.
.318
[8.08]
(1)
(2)
.045
[1.14]
A
.025
[0.64]
.030
[0.76]
Pre-Notch
.025
[0.64]
.100
[2.54]
.318
[8.08]
(1)
(2)
.045
[1.14]
.025
[0.64]
.687
[17.45]
.030
[0.76]
.025
[0.64]
.150
[3.81]
125
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
ECONOMATE Connectors (Continued)
AMP ACTION PIN
Press-Fit Contacts
ACTION PIN contacts provide a reliable press-fit connection.
Localized pressure in the interface area entails oxide
break-through and helps prevent corrosion in the harshest
environments to provide a reliable connection virtually every
time. Also, radial and axial distortion are controlled to meet
today’s standards for multilayer board applications.
PC Board Thickness
ACTION PIN contacts are
designed for use in a variety of
PC board thicknesses. However,
certain ACTION PIN contacts
are to be used in specific ranges
of board thicknesses. To
promote optimum performance,
the recommended board thick-
nesses provided with the con-
nector being used must be
followed.
Annular Ring (See Note)
Drilled Hole
Copper Thickness
Tin-Lead Thickness
Plated Through-Hole
Mounting Hole Specifications
Connector ACTION PIN Contact Drilled Hole Plating Thicknesses Plated Radial Hole Distortion
No. of Dual Material Through-Hole
Centerline Positions Thickness DiameterCopper* Tin-LeadDiameterAverage Maximum
.100 x .200 30, 35, 36,
2.54 x 5.08 40, 50, 60 .025 .0453±.001 .001-.003 .0003 .037-.043 Not Not
.156 x .200 0.64 1.151±0.03 0.03-0.08 0.008 0.94-1.09 Specified Specified
3.96 x 5.08 22 Min.
*Maximum hardness of copper layer is 150 Knoop.
Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].
126
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Application Tooling for ECONOMATE Connectors
Available from Tyco
Electronics is a complete
series of ACTION PIN
Assembly Tooling Kits for
ECONOMATE connector
housings and feed-through
posts. Assembly Kit tools
provide the means for
installing housings and con-
tacts onto printed circuit
boards, as well as removing
housings and contacts from
the printed circuit boards.
All tools are available in kits,
or may be purchased
individually.
In many instances, part
number series are listed in
the charts. Specific dash
numbers and detailed infor-
mation on the contacts and
housings are presented on
the respective product
specification pages. For
specific dash numbers and
complete information on
the tooling, contact
Tyco Electronics.
For ECONOMATE Connectors
ACTION PIN Contacts ECONOMATE Housings ACTION PIN Assembly
Pin Part No. of Dual Part Tool NumbersCenterline Length Numbers Positions Numbers Applicator 265902-
.125 x .125 .702 Carrier Removal Tool 265924-
3.18 x 3.18 17.83 117793-15-60 117796-Housing Assembly Tool 58292-
Housing Removal Tool 265868-1
Pin Replacement Tool 265871-2
Applicator 265904-
.100 x .200 .702 Carrier Removal Tool 265924-
2.54 x 5.08 17.83 117795-15-60 117798-Housing Assembly Tool 265879-
Housing Removal Tool 265868-1
Pin Replacement Tool 265871-2
Applicator 265905-
.156 x .200 .702 Carrier Removal Tool 265924-
3.96 x 5.08 17.83 117285-15-50 117296-Housing Assembly Tool 265881-
Housing Removal Tool 265868-1
Pin Replacement Tool 265871-2
Applicator 265906-
.156 x .200 .475 Carrier Removal Tool 265924-
3.96 x 5.08 12.07 117285-15-50 117296-Housing Assembly Tool 265881-
Housing Removal Tool 265868-1
Pin Replacement Tool 265871-3
Applicator 266129-
.100 x .200 .475 Carrier Removal Tool 265924-
2.54 x 5.08 12.07 117795-15-60 117798-Housing Assembly Tool 265879-
Housing Removal Tool 265868-1
Pin Replacement Tool 265871-3
Applicator 265937-
.100 .340 Carrier Removal Tool 265924-
2.54 8.64 117880-20-60 117879-Housing Assembly Tool 265962-
Housing Removal Tool 265868-2
Pin Replacement Tool 1-265871-1
For Feed-Through Posts
ACTION PIN Contacts ACTION PIN Assembly
Pin No. of Part Tool NumbersCenterline Length Positions Numbers
.100 .500-.687 Applicator 265910-
2.54 12.70-17.45 8-60 117249-Carrier Removal Tool 265924-
Pin Replacement Tool 265871-7
.125 .687 Applicator 265911-
3.18 17.45 8-60 117272-Carrier Removal Tool 265924-
Pin Replacement Tool 265871-7
.150 .687 Applicator 265912-
3.81 17.45 8-50 117269-Carrier Removal Tool 265924-
Pin Replacement Tool 265871-7
.150 .365-.475 Applicator 265931-
3.81 9.27-12.07 8-50 117269-Carrier Removal Tool 265924-
Pin Replacement Tool 265871-7
127
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
High Density Press-Fit Card Edge
Product Facts
High density .050" [1.27]
center spacing.
Staggered contacts for low
insertion force.
Designed for multi-layer
.093" [2.36] daughter cards.
High temperature SMT sol-
der reflow temperatures of
260° for 30 seconds.
Unique pin geometry allows
for even distribution of
forces reducing axial pin
rotation and preserving per-
pendicularity to the
PCB board.
Edge and side coining pro-
vides a uniform pin radius
ensuring maximum contact
without "skiving"
the plated hole.
Full complement of applica-
tion tooling available.
Recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E60980
Certified by Canadian
Standards
Association,
File No. LR 49571
®
High Density (.050" [1.27]
center spacing) Press-Fit
connectors from Tyco
Electronics are designed for
high density backplane or
mid-plane applications.
Compliant pin connectors
from Tyco Electronics meet
or exceed requirements of
current industry standards,
including Bellcore specifica-
tions, which address critical
performance issues such as
hole retention, hole deforma-
tion and environmental per-
f o r m a n c e .
Electrical Characteristics:
Operating Voltage–600VDC (sea
level)
Current Rating –1.5 Amperes
Initial Contact Resistance
30 milliohms
Environmental
Characteristics:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
128
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
.050 [1.27] Centerline For .093 [2.36] Thick Daughter Cards
Material and Finish:
Insulation Resistance—1000
megohms minimum
Contact Retention into PCB—2 lbs.
min.
Insertion Force—10 oz. max.
Mating Force—2 oz. per contact
Housing—High Temp. Glass filled
thermoplastic, UL rating 94V-0
Color—Black
Spring Contact—BeCu
Contact Plating—Palladium Nickel
“A” Spaces • .050 [1.27] = B
.610
[15.49]
.400
[10.15] .332
[8.43]
.132
[3.35]
E
D
C
(Card Slot)
X
X
.421
[10.69]
.066 +.005
-.010
[1.68 +.127
-.254
.461
[11.71]
.016
[.41]
.148 [3.76]
.138 [3.51]
]
Note: Dimension E is Connector Mounting PC Hole Pattern.
Section X-X
129
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Ordering Information
No. of Dual Dimensions
Readout TYCO Acquired
Position A B C D E F Part Number Part Number
20 19 0.950 1.040 1.230 1.100 1.010 147668-2 C9D020PF60048
[24.13] [26.42] [31.24] [27.94] [25.65]
30 29 1.450 1.540 1.730 1.600 1.510 147668-3 C9D030PF60048
[36.83] [39.12] [43.94] [40.64] [38.35]
40 39 1.950 2.040 2.230 2.100 2.010 147668-4 C9D040PF60048
[49.53] [51.82] [56.64] [53.34] [51.05]
50 49 2.450 2.540 2.730 2.600 2.510 147668-5 C9D050PF60048
[62.23] [64.52] [69.34] [66.04] [63.75]
60 59 2.950 3.040 3.230 3.100 3.010 147668-6 C9D060PF60048
[74.93] [77.22] [82.04] [78.74] [76.45]
“A” Spaces • .050 [1.27] = B
“A” Spaces at .050 [1.27] = B
.035 [.89] Typ.
.093
[2.36] Thick PC Board
.166
[4.22]
.066
[1.68]
.075
[1.90]
.096 [2.44]
.585
[14.86]
.030
[.76]
.125
[3.17]
.320
[8.13] Min.
.047
R[1.19] Typ.
45° x .025 [.64]
All Around
.150
[3.81]
F
E
Section Y-Y
Y
Y
Daughter Board
Configuration
Connector Mounting
PC Hole Pattern
ø .024±.002 (.61±.05)
ø .096 (2.44)
130
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
.100 x .100 [2.54 x 2.54] Centerline Press Fit, with Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum
Contact Retention Into PCB
5lbs. min. [356 N]
Insertion Force—10 oz. [44.5 N]
max. measured with a .0700 ± .0001
[1.80±.00254] THK polished blade per
MIL-C-21097C
Withdrawal Force—1 oz. min.
[4.54 N] measured with a .0540 ± .0001
[3.37±.000254] THK polished test blade
per MIL-C-21097C after sizing 3 times
with a .0700 ± .0001 [1.80±.00254] THK
blade
Insulator Body—High Temp. Glass
filled thermoplastic, UL rating 94V-O
Color—Black
Spring Contact—Phosphor Bronze
alloy
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration—MIL-STD-202, method
204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
.100
[2.54]
J
J
.054 to .071
Accepts [3.37 to 1.80] Thk. PC Board
.100
[2.54]
.100
[2.54]
.100
[2.54]
.100
[2.54]
.550
[13.97]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq. Typ.
.365
[9.27] Ref.
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
131
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Press-Fit Board-To-Board)
Ordering Information
.100 [2.54] Centerline/.100 [2.54] Row-To-Row with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .180 [4.57] (Dim. “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 3 C 1 D 1 8 P F 2 9 1 3 3 C 1 D 1 8 P F 2 9 0 4 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 3 C 1 D 2 0 P F 2 9 1 3 3 C 1 D 2 0 P F 2 9 0 4 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 3 C 1 D 2 2 P F 2 9 1 3 3 C 1 D 2 2 P F 2 9 0 4 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 3 C 1 D 2 5 P F 2 9 1 3 3 C 1 D 2 5 P F 2 9 0 4 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 3 C 1 D 2 8 P F 2 9 1 3 3 C 1 D 2 8 P F 2 9 0 4 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 3 C 1 D 3 0 P F 2 9 1 3 3 C 1 D 3 0 P F 2 9 0 4 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 3 C 1 D 3 5 P F 2 9 1 3 3 C 1 D 3 5 P F 2 9 0 4 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 3 C 1 D 3 6 P F 2 9 1 3 3 C 1 D 3 6 P F 2 9 0 4 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 3 C 1 D 4 0 P F 2 9 1 3 3 C 1 D 4 0 P F 2 9 0 4 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 3 C 1 D 4 3 P F 2 9 1 3 3 C 1 D 4 3 P F 2 9 0 4 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 3 C 1 D 4 5 P F 2 9 1 3 3 C 1 D 4 5 P F 2 9 0 4 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 3 C 1 D 5 0 P F 2 9 1 3 3 C 1 D 5 0 P F 2 9 0 4 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 3 C 1 D 6 0 P F 2 9 1 3 3 C 1 D 6 0 P F 2 9 0 4 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
Tail Length .475 [12.07] (Dim. “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 5 C 1 D 1 8 P F 2 9 1 3 5 C 1 D 1 8 P F 2 9 0 4 5
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 5 C 1 D 2 0 P F 2 9 1 3 5 C 1 D 2 0 P F 2 9 0 4 5
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 5 C 1 D 2 2 P F 2 9 1 3 5 C 1 D 2 2 P F 2 9 0 4 5
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 5 C 1 D 2 5 P F 2 9 1 3 5 C 1 D 2 5 P F 2 9 0 4 5
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 5 C 1 D 2 8 P F 2 9 1 3 5 C 1 D 2 8 P F 2 9 0 4 5
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 5 C 1 D 3 0 P F 2 9 1 3 5 C 1 D 3 0 P F 2 9 0 4 5
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 5 C 1 D 3 5 P F 2 9 1 3 5 C 1 D 3 5 P F 2 9 0 4 5
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 5 C 1 D 3 6 P F 2 9 1 3 5 C 1 D 3 6 P F 2 9 0 4 5
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 5 C 1 D 4 0 P F 2 9 1 3 5 C 1 D 4 0 P F 2 9 0 4 5
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 5 C 1 D 4 3 P F 2 9 1 3 5 C 1 D 4 3 P F 2 9 0 4 5
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 5 C 1 D 4 5 P F 2 9 1 3 5 C 1 D 4 5 P F 2 9 0 4 5
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 5 C 1 D 5 0 P F 2 9 1 3 5 C 1 D 5 0 P F 2 9 0 4 5
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 5 C 1 D 6 0 P F 2 9 1 3 5 C 1 D 6 0 P F 2 9 0 4 5
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
132
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.100" [2.54] Centerline / .100" [2.54] Row-to-Row with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .625 [15.88] (Dim. “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 C 1 D 1 8 P F 2 9 0 1 7 C 1 D 1 8 P F 2 9 1 3 7 C 1 D 1 8 P F 2 9 0 4 7
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 C 1 D 2 0 P F 2 9 0 1 7 C 1 D 2 0 P F 2 9 1 3 7 C 1 D 2 0 P F 2 9 0 4 7
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 C 1 D 2 2 P F 2 9 0 1 7 C 1 D 2 2 P F 2 9 1 3 7 C 1 D 2 2 P F 2 9 0 4 7
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 C 1 D 2 5 P F 2 9 0 1 7 C 1 D 2 5 P F 2 9 1 3 7 C 1 D 2 5 P F 2 9 0 4 7
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 C 1 D 2 8 P F 2 9 0 1 7 C 1 D 2 8 P F 2 9 1 3 7 C 1 D 2 8 P F 2 9 0 4 7
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 C 1 D 3 0 P F 2 9 0 1 7 C 1 D 3 0 P F 2 9 1 3 7 C 1 D 3 0 P F 2 9 0 4 7
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 C 1 D 3 5 P F 2 9 0 1 7 C 1 D 3 5 P F 2 9 1 3 7 C 1 D 3 5 P F 2 9 0 4 7
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 C 1 D 3 6 P F 2 9 0 1 7 C 1 D 3 6 P F 2 9 1 3 7 C 1 D 3 6 P F 2 9 0 4 7
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 C 1 D 4 0 P F 2 9 0 1 7 C 1 D 4 0 P F 2 9 1 3 7 C 1 D 4 0 P F 2 9 0 4 7
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 C 1 D 4 3 P F 2 9 0 1 7 C 1 D 4 3 P F 2 9 1 3 7 C 1 D 4 3 P F 2 9 0 4 7
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 C 1 D 4 5 P F 2 9 0 1 7 C 1 D 4 5 P F 2 9 1 3 7 C 1 D 4 5 P F 2 9 0 4 7
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 C 1 D 5 0 P F 2 9 0 1 7 C 1 D 5 0 P F 2 9 1 3 7 C 1 D 5 0 P F 2 9 0 4 7
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 C 1 D 6 0 P F 2 9 0 1 7 C 1 D 6 0 P F 2 9 1 3 7 C 1 D 6 0 P F 2 9 0 4 7
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
133
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.100 x .200 [2.54 x 5.08] Centerline Press-Fit, Full Scoop
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB
5lbs. min. [356 N]
Insertion Force—10 oz. [44.5 N]
max. measured with a .0700 ± .0001
[1.80±.00254] THK polished blade per
MIL-C-21097C
Withdrawal Force—1 oz. min.
[4.5 N] measured with a .0540 ± .0001
[3.37±.00254] THK polished test blade
per MIL-C-21097C after sizing 3 times
with a .0700 ± .0001 [1.80±.00254] THK
blade
Insulator Body—High Temp. Glass
filled thermoplastic, UL rating 94V-O
Color—Black
Spring Contact—Phosphor Bronze
alloy
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties
Operating Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Contact Resistance—10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
.200
[5.08]
.100
[2.54]
.200
[5.08]
B
C
B
A
C
Dim E
J
.395/.510
[10.03/12.95] Card Slot Depth
.395/.510
[10.03/12.95] Card Slot Depth
.100
[2.54]
.390
[9.91]
J
.645
[16.38] Ref.
.21
[5.33] Point of Contact
.040±.003
[1.02±.08] Dia.
.020±.010
[.51±.25] Contact Gap
134
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth
Tail Length .670 [17.02] (DIM “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 1 2 W 8 D 1 8 P F 2 9 0 4 2
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 1 2 W 8 D 2 0 P F 2 9 0 4 2
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 1 2 W 8 D 2 2 P F 2 9 0 4 2
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 1 2 W 8 D 2 5 P F 2 9 0 4 2
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 1 2 W 8 D 2 8 P F 2 9 0 4 2
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 1 2 W 8 D 3 0 P F 2 9 0 4 2
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 1 2 W 8 D 3 5 P F 2 9 0 4 2
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 1 2 W 8 D 3 6 P F 2 9 0 4 2
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 1 2 W 8 D 4 0 P F 2 9 0 4 2
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 1 2 W 8 D 4 3 P F 2 9 0 4 2
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 1 2 W 8 D 4 5 P F 2 9 0 4 2
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 1 2 W 8 D 5 0 P F 2 9 0 4 2
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 1 2 W 8 D 6 0 P F 2 9 0 4 2
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
Tail Length .180 [4.57] (DIM “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 1 3 W 8 D 1 8 P F 2 9 0 4 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 1 3 W 8 D 2 0 P F 2 9 0 4 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 1 3 W 8 D 2 2 P F 2 9 0 4 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 1 3 W 8 D 2 5 P F 2 9 0 4 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 1 3 W 8 D 2 8 P F 2 9 0 4 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 1 3 W 8 D 3 0 P F 2 9 0 4 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 1 3 W 8 D 3 5 P F 2 9 0 4 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 1 3 W 8 D 3 6 P F 2 9 0 4 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 1 3 W 8 D 4 0 P F 2 9 0 4 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 1 3 W 8 D 4 3 P F 2 9 0 4 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 1 3 W 8 D 4 5 P F 2 9 0 4 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 1 3 W 8 D 5 0 P F 2 9 0 4 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 1 3 W 8 D 6 0 P F 2 9 0 4 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
135
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.100 x .200 [2.54 x 5.08] Centerline, Press-Fit, Full Scoop with Standoffs
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB
5lbs. min. [356 N]
Insertion Force—10 oz. [44.5 N]
max. measured with a .0700 ± .0001
[1.80±.00254] THK polished blade per
MIL-C-21097C
Withdrawal Force—1 oz. min.
[4.5 N] measured with a .0540 ± .0001
[3.37±.00254] THK polished test blade
per MIL-C-21097C after sizing 3 times
with a .0700 ± .0001 [1.80±.00254] THK
blade
Insulator Body—High Temp. Glass
filled thermoplastic, UL rating 94V-O
Color—Black
Spring Contact—Phosphor Bronze
alloy
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
.200
[5.08]
.100
[2.54]
.200
[5.08]
B
C
B
A
C
Dim C
J
.395/.510
[10.03/12.95] Card Slot Depth
.395/.510
[10.03/12.95] Card Slot Depth
.100
[2.54]
.390
[9.91]
J
.705
[17.91] Ref.
.21
[5.33] Point of Contact
.040±.003
[1.02±.08] Dia.
.020±.010
[.51±.25 ] Contact Gap
136
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.100 [2.54] Centerline / .200 [5.08] Row-to-Row Full Scoop with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .510 [12.95] Card Slot Depth .395 [10.03] Card Slot Depth
Tail Length .670 [17.02] (DIM “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 6 2 W 8 D 1 8 P F 2 9 0 9 2
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 6 2 W 8 D 2 0 P F 2 9 0 9 2
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 6 2 W 8 D 2 2 P F 2 9 0 9 2
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 6 2 W 8 D 2 5 P F 2 9 0 9 2
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 6 2 W 8 D 2 8 P F 2 9 0 9 2
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 6 2 W 8 D 3 0 P F 2 9 0 9 2
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 6 2 W 8 D 3 5 P F 2 9 0 9 2
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 6 2 W 8 D 3 6 P F 2 9 0 9 2
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 6 2 W 8 D 4 0 P F 2 9 0 9 2
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 6 2 W 8 D 4 3 P F 2 9 0 9 2
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 6 2 W 8 D 4 5 P F 2 9 0 9 2
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 6 2 W 8 D 5 0 P F 2 9 0 9 2
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 6 2 W 8 D 6 0 P F 2 9 0 9 2
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
Tail Length .180 [4.57] (DIM “J”)
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 P F 2 9 0 6 3 W 8 D 1 8 P F 2 9 0 9 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 P F 2 9 0 6 3 W 8 D 2 0 P F 2 9 0 9 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 P F 2 9 0 6 3 W 8 D 2 2 P F 2 9 0 9 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 P F 2 9 0 6 3 W 8 D 2 5 P F 2 9 0 9 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 P F 2 9 0 6 3 W 8 D 2 8 P F 2 9 0 9 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 P F 2 9 0 6 3 W 8 D 3 0 P F 2 9 0 9 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 P F 2 9 0 6 3 W 8 D 3 5 P F 2 9 0 9 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 P F 2 9 0 6 3 W 8 D 3 6 P F 2 9 0 9 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 P F 2 9 0 6 3 W 8 D 4 0 P F 2 9 0 9 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 P F 2 9 0 6 3 W 8 D 4 3 P F 2 9 0 9 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 P F 2 9 0 6 3 W 8 D 4 5 P F 2 9 0 9 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 P F 2 9 0 6 3 W 8 D 5 0 P F 2 9 0 9 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 P F 2 9 0 6 3 W 8 D 6 0 P F 2 9 0 9 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
137
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.100 x .200 [2.54 x 5.08] Centerline, Press-Fit without Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB—5 lbs.
[356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.200
[5.08]
J
J
.054 to .071
Accepts [3.37 to 1.80] Thk. PC Board
.100
[2.54]
.200
[5.08]
.100
[2.54]
.100
[2.54]
.550
[13.97]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq. Typ.
.365
[9.27] Ref.
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
138
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row without Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .670 [17.02] (“J”)
60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 3 2 C 8 D 0 6 P F 2 9 1 4 2 C 8 D 0 6 P F 2 9 0 2 2
2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 3 2 C 8 D 1 0 P F 2 9 1 4 2 C 8 D 1 0 P F 2 9 0 2 2
3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 3 2 C 8 D 1 2 P F 2 9 1 4 2 C 8 D 1 2 P F 2 9 0 2 2
3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 3 2 C 8 D 1 5 P F 2 9 1 4 2 C 8 D 1 5 P F 2 9 0 2 2
4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 3 2 C 8 D 2 0 P F 2 9 1 4 2 C 8 D 2 0 P F 2 9 0 2 2
5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 3 2 C 8 D 2 2 P F 2 9 1 4 2 C 8 D 2 2 P F 2 9 0 2 2
6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 3 2 C 8 D 2 5 P F 2 9 1 4 2 C 8 D 2 5 P F 2 9 0 2 2
7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 3 2 C 8 D 2 8 P F 2 9 1 4 2 C 8 D 2 8 P F 2 9 0 2 2
7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 3 2 C 8 D 3 0 P F 2 9 1 4 2 C 8 D 3 0 P F 2 9 0 2 2
8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 3 2 C 8 D 3 1 P F 2 9 1 4 2 C 8 D 3 1 P F 2 9 0 2 2
8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 3 2 C 8 D 3 5 P F 2 9 1 4 2 C 8 D 3 5 P F 2 9 0 2 2
9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 3 2 C 8 D 3 6 P F 2 9 1 4 2 C 8 D 3 6 P F 2 9 0 2 2
9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 3 2 C 8 D 4 0 P F 2 9 1 4 2 C 8 D 4 0 P F 2 9 0 2 2
1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 3 2 C 8 D 4 3 P F 2 9 1 4 2 C 8 D 4 3 P F 2 9 0 2 2
1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 3 2 C 8 D 5 0 P F 2 9 1 4 2 C 8 D 5 0 P F 2 9 0 2 2
1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 3 2 C 8 D 6 0 P F 2 9 1 4 2 C 8 D 6 0 P F 2 9 0 2 2
1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .180 [4.57] (“J”)
60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 3 3 C 8 D 0 6 P F 2 9 1 4 3 C 8 D 0 6 P F 2 9 0 2 3
2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 3 3 C 8 D 1 0 P F 2 9 1 4 3 C 8 D 1 0 P F 2 9 0 2 3
3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 3 3 C 8 D 1 2 P F 2 9 1 4 3 C 8 D 1 2 P F 2 9 0 2 3
3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 3 3 C 8 D 1 5 P F 2 9 1 4 3 C 8 D 1 5 P F 2 9 0 2 3
4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 3 3 C 8 D 2 0 P F 2 9 1 4 3 C 8 D 2 0 P F 2 9 0 2 3
5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 3 3 C 8 D 2 2 P F 2 9 1 4 3 C 8 D 2 2 P F 2 9 0 2 3
6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 3 3 C 8 D 2 5 P F 2 9 1 4 3 C 8 D 2 5 P F 2 9 0 2 3
7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 3 3 C 8 D 2 8 P F 2 9 1 4 3 C 8 D 2 8 P F 2 9 0 2 3
7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 3 3 C 8 D 3 0 P F 2 9 1 4 3 C 8 D 3 0 P F 2 9 0 2 3
8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 3 3 C 8 D 3 1 P F 2 9 1 4 3 C 8 D 3 1 P F 2 9 0 2 3
8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 3 3 C 8 D 3 5 P F 2 9 1 4 3 C 8 D 3 5 P F 2 9 0 2 3
9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 3 3 C 8 D 3 6 P F 2 9 1 4 3 C 8 D 3 6 P F 2 9 0 2 3
9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 3 3 C 8 D 4 0 P F 2 9 1 4 3 C 8 D 4 0 P F 2 9 0 2 3
1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 3 3 C 8 D 4 3 P F 2 9 1 4 3 C 8 D 4 3 P F 2 9 0 2 3
1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 3 3 C 8 D 5 0 P F 2 9 1 4 3 C 8 D 5 0 P F 2 9 0 2 3
1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 3 3 C 8 D 6 0 P F 2 9 1 4 3 C 8 D 6 0 P F 2 9 0 2 3
1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
139
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.100 x .200 [2.54 x 5.08] Centerline, Press-Fit with Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB—5 lbs.
[356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.200
[5.08]
J
J
.054 to .071
Accepts [1.37 to 1.80] Thk. PC Board
.100
[2.54]
.200
[5.08]
.100
[2.54]
.100
[2.54]
.610
[15.49]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq.
.365
[9.27] Ref.
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
140
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering InformationOrdering Information
.100 [2.54] Center-to-Center/.200 [5.08] Row-To-Row with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .670 [17.02] (dim “J”)
60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 1 2 C 8 D 0 6 P F 2 9 1 3 2 C 8 D 0 6 P F 2 9 0 4 2
2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 1 2 C 8 D 1 0 P F 2 9 1 3 2 C 8 D 1 0 P F 2 9 0 4 2
3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 1 2 C 8 D 1 2 P F 2 9 1 3 2 C 8 D 1 2 P F 2 9 0 4 2
3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 1 2 C 8 D 1 5 P F 2 9 1 3 2 C 8 D 1 5 P F 2 9 0 4 2
4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 1 2 C 8 D 2 0 P F 2 9 1 3 2 C 8 D 2 0 P F 2 9 0 4 2
5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 1 2 C 8 D 2 2 P F 2 9 1 3 2 C 8 D 2 2 P F 2 9 0 4 2
6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 1 2 C 8 D 2 5 P F 2 9 1 3 2 C 8 D 2 5 P F 2 9 0 4 2
7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 1 2 C 8 D 2 8 P F 2 9 1 3 2 C 8 D 2 8 P F 2 9 0 4 2
7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 1 2 C 8 D 3 0 P F 2 9 1 3 2 C 8 D 3 0 P F 2 9 0 4 2
8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 1 2 C 8 D 3 1 P F 2 9 1 3 2 C 8 D 3 1 P F 2 9 0 4 2
8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 1 2 C 8 D 3 5 P F 2 9 1 3 2 C 8 D 3 5 P F 2 9 0 4 2
9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 1 2 C 8 D 3 6 P F 2 9 1 3 2 C 8 D 3 6 P F 2 9 0 4 2
9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 1 2 C 8 D 4 0 P F 2 9 1 3 2 C 8 D 4 0 P F 2 9 0 4 2
1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 1 2 C 8 D 4 3 P F 2 9 1 3 2 C 8 D 4 3 P F 2 9 0 4 2
1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 1 2 C 8 D 5 0 P F 2 9 1 3 2 C 8 D 5 0 P F 2 9 0 4 2
1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 1 2 C 8 D 6 0 P F 2 9 1 3 2 C 8 D 6 0 P F 2 9 0 4 2
1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .180 [4.57] (dim J)
60 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 P F 2 9 0 1 3 C 8 D 0 6 P F 2 9 1 3 3 C 8 D 0 6 P F 2 9 0 4 3
2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 P F 2 9 0 1 3 C 8 D 1 0 P F 2 9 1 3 3 C 8 D 1 0 P F 2 9 0 4 3
3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 P F 2 9 0 1 3 C 8 D 1 2 P F 2 9 1 3 3 C 8 D 1 2 P F 2 9 0 4 3
3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 P F 2 9 0 1 3 C 8 D 1 5 P F 2 9 1 3 3 C 8 D 1 5 P F 2 9 0 4 3
4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
2 0 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 P F 2 9 0 1 3 C 8 D 2 0 P F 2 9 1 3 3 C 8 D 2 0 P F 2 9 0 4 3
5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 P F 2 9 0 1 3 C 8 D 2 2 P F 2 9 1 3 3 C 8 D 2 2 P F 2 9 0 4 3
6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 P F 2 9 0 1 3 C 8 D 2 5 P F 2 9 1 3 3 C 8 D 2 5 P F 2 9 0 4 3
7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 P F 2 9 0 1 3 C 8 D 2 8 P F 2 9 1 3 3 C 8 D 2 8 P F 2 9 0 4 3
7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 P F 2 9 0 1 3 C 8 D 3 0 P F 2 9 1 3 3 C 8 D 3 0 P F 2 9 0 4 3
8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 P F 2 9 0 1 3 C 8 D 3 1 P F 2 9 1 3 3 C 8 D 3 1 P F 2 9 0 4 3
8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 P F 2 9 0 1 3 C 8 D 3 5 P F 2 9 1 3 3 C 8 D 3 5 P F 2 9 0 4 3
9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 P F 2 9 0 1 3 C 8 D 3 6 P F 2 9 1 3 3 C 8 D 3 6 P F 2 9 0 4 3
9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 P F 2 9 0 1 3 C 8 D 4 0 P F 2 9 1 3 3 C 8 D 4 0 P F 2 9 0 4 3
1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 P F 2 9 0 1 3 C 8 D 4 3 P F 2 9 1 3 3 C 8 D 4 3 P F 2 9 0 4 3
1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 P F 2 9 0 1 3 C 8 D 5 0 P F 2 9 1 3 3 C 8 D 5 0 P F 2 9 0 4 3
1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 P F 2 9 0 1 3 C 8 D 6 0 P F 2 9 1 3 3 C 8 D 6 0 P F 2 9 0 4 3
1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
141
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.125 x .250 [3.18 x 6.35] Centerline without Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB—5 lbs.
[356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.250
[6.35]
J
J
.054 to .071
Accepts [1.37 to 1.80] Thk. PC Board
.125
[3.18]
.250
[6.35]
.125
[3.18]
.125
[3.18]
.550
[13.97]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq. Typ.
.365
[9.27]
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
142
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.125 [3.18] Centerline /.250 [6.35] Row-to-Row without Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .670 [17.02] (DIM “J”)
61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 3 2 C 7 D 0 6 P F 2 9 1 4 2 C 7 D 0 6 P F 2 9 0 2 2
2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 3 2 C 7 D 1 0 P F 2 9 1 4 2 C 7 D 1 0 P F 2 9 0 2 2
3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 3 2 C 7 D 1 2 P F 2 9 1 4 2 C 7 D 1 2 P F 2 9 0 2 2
4 5 . 3 4 4 1 . 2 8 3 4 . 9 3
1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 3 2 C 7 D 1 5 P F 2 9 1 4 2 C 7 D 1 5 P F 2 9 0 2 2
5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 3 2 C 7 D 1 8 P F 2 9 1 4 2 C 7 D 1 8 P F 2 9 0 2 2
6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 3 2 C 7 D 2 0 P F 2 9 1 4 2 C 7 D 2 0 P F 2 9 0 2 2
7 0 . 7 4 6 6 . 6 8 6 0 . 3 3
2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 3 2 C 7 D 2 2 P F 2 9 1 4 2 C 7 D 2 2 P F 2 9 0 2 2
7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 3 2 C 7 D 2 5 P F 2 9 1 4 2 C 7 D 2 5 P F 2 9 0 2 2
8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 3 2 C 7 D 2 8 P F 2 9 1 4 2 C 7 D 2 8 P F 2 9 0 2 2
9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 3 2 C 7 D 3 0 P F 2 9 1 4 2 C 7 D 3 0 P F 2 9 0 2 2
1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 3 2 C 7 D 3 1 P F 2 9 1 4 2 C 7 D 3 1 P F 2 9 0 2 2
1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 3 2 C 7 D 3 5 P F 2 9 1 4 2 C 7 D 3 5 P F 2 9 0 2 2
1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 3 2 C 7 D 3 6 P F 2 9 1 4 2 C 7 D 3 6 P F 2 9 0 2 2
1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 3 2 C 7 D 4 0 P F 2 9 1 4 2 C 7 D 4 0 P F 2 9 0 2 2
1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 3 2 C 7 D 4 3 P F 2 9 1 4 2 C 7 D 4 3 P F 2 9 0 2 2
1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 3 2 C 7 D 5 0 P F 2 9 1 4 2 C 7 D 5 0 P F 2 9 0 2 2
1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
Tail Length .180 [4.57] (DIM “J”)
61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 3 3 C 7 D 0 6 P F 2 9 1 4 3 C 7 D 0 6 P F 2 9 0 2 3
2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 3 3 C 7 D 1 0 P F 2 9 1 4 3 C 7 D 1 0 P F 2 9 0 2 3
3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 3 3 C 7 D 1 2 P F 2 9 1 4 3 C 7 D 1 2 P F 2 9 0 2 3
4 5 . 3 4 4 1 . 2 8 3 4 . 9 3
1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 3 3 C 7 D 1 5 P F 2 9 1 4 3 C 7 D 1 5 P F 2 9 0 2 3
5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 3 3 C 7 D 1 8 P F 2 9 1 4 3 C 7 D 1 8 P F 2 9 0 2 3
6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 3 3 C 7 D 2 0 P F 2 9 1 4 3 C 7 D 2 0 P F 2 9 0 2 3
7 0 . 7 4 6 6 . 6 8 6 0 . 3 3
2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 3 3 C 7 D 2 2 P F 2 9 1 4 3 C 7 D 2 2 P F 2 9 0 2 3
7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 3 3 C 7 D 2 5 P F 2 9 1 4 3 C 7 D 2 5 P F 2 9 0 2 3
8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 3 3 C 7 D 2 8 P F 2 9 1 4 3 C 7 D 2 8 P F 2 9 0 2 3
9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 3 3 C 7 D 3 0 P F 2 9 1 4 3 C 7 D 3 0 P F 2 9 0 2 3
1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 3 3 C 7 D 3 1 P F 2 9 1 4 3 C 7 D 3 1 P F 2 9 0 2 3
1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 3 3 C 7 D 3 5 P F 2 9 1 4 3 C 7 D 3 5 P F 2 9 0 2 3
1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 3 3 C 7 D 3 6 P F 2 9 1 4 3 C 7 D 3 6 P F 2 9 0 2 3
1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 3 3 C 7 D 4 0 P F 2 9 1 4 3 C 7 D 4 0 P F 2 9 0 2 3
1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 3 3 C 7 D 4 3 P F 2 9 1 4 3 C 7 D 4 3 P F 2 9 0 2 3
1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 3 3 C 7 D 5 0 P F 2 9 1 4 3 C 7 D 5 0 P F 2 9 0 2 3
1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
143
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.125 x .250 [3.18 x 6.35] Centerline with Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB—5 lbs.
[356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.200
[5.08]
J
J
.054 to .071
Accepts [1.37 to 1.80] Thk. PC Board
.125
[3.18]
.250
[6.35]
.125
[3.18]
.125
[3.18]
.550
[13.97]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq. Typ.
.365
[9.27]
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
144
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.125 [3.18] Centerline /.250 [6.35] Row-to-Row with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
Tail Length .670 [17.02] (DIM “J”)
61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 1 2 C 7 D 0 6 P F 2 9 1 3 2 C 7 D 0 6 P F 2 9 0 4 2
2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 1 2 C 7 D 1 0 P F 2 9 1 3 2 C 7 D 1 0 P F 2 9 0 4 2
3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 1 2 C 7 D 1 2 P F 2 9 1 3 2 C 7 D 1 2 P F 2 9 0 4 2
4 5 . 3 4 4 1 . 2 8 3 4 . 9 3
1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 1 2 C 7 D 1 5 P F 2 9 1 3 2 C 7 D 1 5 P F 2 9 0 4 2
5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 1 2 C 7 D 1 8 P F 2 9 1 3 2 C 7 D 1 8 P F 2 9 0 4 2
6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 1 2 C 7 D 2 0 P F 2 9 1 3 2 C 7 D 2 0 P F 2 9 0 4 2
7 0 . 7 4 6 6 . 6 8 6 0 . 3 3
2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 1 2 C 7 D 2 2 P F 2 9 1 3 2 C 7 D 2 2 P F 2 9 0 4 2
7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 1 2 C 7 D 2 5 P F 2 9 1 3 2 C 7 D 2 5 P F 2 9 0 4 2
8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 1 2 C 7 D 2 8 P F 2 9 1 3 2 C 7 D 2 8 P F 2 9 0 4 2
9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 1 2 C 7 D 3 0 P F 2 9 1 3 2 C 7 D 3 0 P F 2 9 0 4 2
1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 1 2 C 7 D 3 1 P F 2 9 1 3 2 C 7 D 3 1 P F 2 9 0 4 2
1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 1 2 C 7 D 3 5 P F 2 9 1 3 2 C 7 D 3 5 P F 2 9 0 4 2
1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 1 2 C 7 D 3 6 P F 2 9 1 3 2 C 7 D 3 6 P F 2 9 0 4 2
1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 1 2 C 7 D 4 0 P F 2 9 1 3 2 C 7 D 4 0 P F 2 9 0 4 2
1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 1 2 C 7 D 4 3 P F 2 9 1 3 2 C 7 D 4 3 P F 2 9 0 4 2
1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 1 2 C 7 D 5 0 P F 2 9 1 3 2 C 7 D 5 0 P F 2 9 0 4 2
1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
Tail Length .180 [4.57] (DIM “J”)
61 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 P F 2 9 0 1 3 C 7 D 0 6 P F 2 9 1 3 3 C 7 D 0 6 P F 2 9 0 4 3
2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 P F 2 9 0 1 3 C 7 D 1 0 P F 2 9 1 3 3 C 7 D 1 0 P F 2 9 0 4 3
3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 2 1 . 7 8 5 1 . 6 2 5 1 . 3 7 5 C 7 D 1 2 P F 2 9 0 1 3 C 7 D 1 2 P F 2 9 1 3 3 C 7 D 1 2 P F 2 9 0 4 3
4 5 . 3 4 4 1 . 2 8 3 4 . 9 3
1 5 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 P F 2 9 0 1 3 C 7 D 1 5 P F 2 9 1 3 3 C 7 D 1 5 P F 2 9 0 4 3
5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 P F 2 9 0 1 3 C 7 D 1 8 P F 2 9 1 3 3 C 7 D 1 8 P F 2 9 0 4 3
6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 0 2 . 7 8 5 2 . 6 2 5 2 . 3 7 5 C 7 D 2 0 P F 2 9 0 1 3 C 7 D 2 0 P F 2 9 1 3 3 C 7 D 2 0 P F 2 9 0 4 3
7 0 . 7 4 6 6 . 6 8 6 0 . 3 3
2 2 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 P F 2 9 0 1 3 C 7 D 2 2 P F 2 9 1 3 3 C 7 D 2 2 P F 2 9 0 4 3
7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 P F 2 9 0 1 3 C 7 D 2 5 P F 2 9 1 3 3 C 7 D 2 5 P F 2 9 0 4 3
8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 P F 2 9 0 1 3 C 7 D 2 8 P F 2 9 1 3 3 C 7 D 2 8 P F 2 9 0 4 3
9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 P F 2 9 0 1 3 C 7 D 3 0 P F 2 9 1 3 3 C 7 D 3 0 P F 2 9 0 4 3
1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 P F 2 9 0 1 3 C 7 D 3 1 P F 2 9 1 3 3 C 7 D 3 1 P F 2 9 0 4 3
1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 P F 2 9 0 1 3 C 7 D 3 5 P F 2 9 1 3 3 C 7 D 3 5 P F 2 9 0 4 3
1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 P F 2 9 0 1 3 C 7 D 3 6 P F 2 9 1 3 3 C 7 D 3 6 P F 2 9 0 4 3
1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 P F 2 9 0 1 3 C 7 D 4 0 P F 2 9 1 3 3 C 7 D 4 0 P F 2 9 0 4 3
1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 P F 2 9 0 1 3 C 7 D 4 3 P F 2 9 1 3 3 C 7 D 4 3 P F 2 9 0 4 3
1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 P F 2 9 0 1 3 C 7 D 5 0 P F 2 9 1 3 3 C 7 D 5 0 P F 2 9 0 4 3
1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
NOTE: Optional stacking designs are available (consult Tyco Electronics).
145
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.156 x .200 [3.18 x 5.08] Centerline without Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB
5 lbs. [356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.200
[5.08]
J
.054 to .071
Accepts [1.37 to 1.80] Thk. PC Board
.156
[3.96]
.156
[3.96]
Dim C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
J
.156
[3.96]
.550
[13.97]
C
.025
[.64] Sq. Typ.
.365
[9.27] Ref.
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
.200
[5.08]
146
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.156 [3.18] Centerline/.200 [5.08] Row-to-Row without Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.84] Card Slot Depth .415 [10.54] Card Slot Depth
.670 [17.02] Tail Length (DIM “J”)
61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 3 2 C 6 D 0 6 P F 2 9 1 4 2 C 6 D 0 6 P F 2 9 0 2 2
3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 3 2 C 6 D 1 0 P F 2 9 1 4 2 C 6 D 1 0 P F 2 9 0 2 2
4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 3 2 C 6 D 1 2 P F 2 9 1 4 2 C 6 D 1 2 P F 2 9 0 2 2
5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 3 2 C 6 D 1 5 P F 2 9 1 4 2 C 6 D 1 5 P F 2 9 0 2 2
6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 3 2 C 6 D 1 8 P F 2 9 1 4 2 C 6 D 1 8 P F 2 9 0 2 2
7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 3 2 C 6 D 2 0 P F 2 9 1 4 2 C 6 D 2 0 P F 2 9 0 2 2
8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 3 2 C 6 D 2 2 P F 2 9 1 4 2 C 6 D 2 2 P F 2 9 0 2 2
9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 3 2 C 6 D 2 5 P F 2 9 1 4 2 C 6 D 2 5 P F 2 9 0 2 2
1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 3 2 C 6 D 2 8 P F 2 9 1 4 2 C 6 D 2 8 P F 2 9 0 2 2
1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 3 2 C 6 D 3 0 P F 2 9 1 4 2 C 6 D 3 0 P F 2 9 0 2 2
1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 3 2 C 6 D 3 1 P F 2 9 1 4 2 C 6 D 3 1 P F 2 9 0 2 2
1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 3 2 C 6 D 3 5 P F 2 9 1 4 2 C 6 D 3 5 P F 2 9 0 2 2
1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 3 2 C 6 D 3 6 P F 2 9 1 4 2 C 6 D 3 6 P F 2 9 0 2 2
1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 3 2 C 6 D 4 0 P F 2 9 1 4 2 C 6 D 4 0 P F 2 9 0 2 2
1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 3 2 C 6 D 4 3 P F 2 9 1 4 2 C 6 D 4 3 P F 2 9 0 2 2
1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
.180 [4.57] Tail Length (DIM “J”)
61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 3 3 C 6 D 0 6 P F 2 9 1 4 3 C 6 D 0 6 P F 2 9 0 2 3
3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 3 3 C 6 D 1 0 P F 2 9 1 4 3 C 6 D 1 0 P F 2 9 0 2 3
4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 3 3 C 6 D 1 2 P F 2 9 1 4 3 C 6 D 1 2 P F 2 9 0 2 3
5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 3 3 C 6 D 1 5 P F 2 9 1 4 3 C 6 D 1 5 P F 2 9 0 2 3
6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 3 3 C 6 D 1 8 P F 2 9 1 4 3 C 6 D 1 8 P F 2 9 0 2 3
7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 3 3 C 6 D 2 0 P F 2 9 1 4 3 C 6 D 2 0 P F 2 9 0 2 3
8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 3 3 C 6 D 2 2 P F 2 9 1 4 3 C 6 D 2 2 P F 2 9 0 2 3
9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 3 3 C 6 D 2 5 P F 2 9 1 4 3 C 6 D 2 5 P F 2 9 0 2 3
1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 3 3 C 6 D 2 8 P F 2 9 1 4 3 C 6 D 2 8 P F 2 9 0 2 3
1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 3 3 C 6 D 3 0 P F 2 9 1 4 3 C 6 D 3 0 P F 2 9 0 2 3
1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 3 3 C 6 D 3 1 P F 2 9 1 4 3 C 6 D 3 1 P F 2 9 0 2 3
1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 3 3 C 6 D 3 5 P F 2 9 1 4 3 C 6 D 3 5 P F 2 9 0 2 3
1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 3 3 C 6 D 3 6 P F 2 9 1 4 3 C 6 D 3 6 P F 2 9 0 2 3
1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 3 3 C 6 D 4 0 P F 2 9 1 4 3 C 6 D 4 0 P F 2 9 0 2 3
1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 3 3 C 6 D 4 3 P F 2 9 1 4 3 C 6 D 4 3 P F 2 9 0 2 3
1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
147
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
.156 x .200 [3.18 x 5.08] Centerline with Standoffs
Product Facts
Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance
5000 megohms minimum.
Contact Retention Into PCB—5 lbs.
[356 N]
Insertion/Withdrawal Force
8 oz./2 oz. [35.6 N/ 8.9 N] average
contact pair using .0620 [1.57] steel
blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operating Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance
10 milliohms
Environmental Properties:
Operating Temperature
-55˚C to +125˚C
Temperature Cycling
MIL-STD-202 method 107
Vibration
MIL-STD-202, method 204
Application Tooling:
Insertion Tool—page 150
Related Product Data:
Daughter Card Edge Pattern
page 57
Note: Open ends and open/closed
ends are available. Consult Tyco
E l e c t r o n i c s .
.200
[5.08]
J
J
.054 to .071
Accepts [1.37 to 1.80] Thk. PC Board
.156
[3.96]
.200
[5.08]
.156
[3.96]
.156
[3.96]
.610
[15.49]
Dim C
C
C
B
A
.020
[.51] Contact Gap
Card Slot
Depth
.300 [7.62]
.350 [8.89]
.415 [10.54]
.040±.003
[1.02±.08] Dia.
.025
[.64] Sq. Typ.
.365
[9.27] Ref.
. 1 2 0±. 0 0 3
[3.05±.25]
Point of
Contact
148
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Ordering Information
.156 [3.18] Centerline/.200 [5.08] Row-to-Row with Standoffs
No. of Dual D i m e n s i o n s Acquired Part Numbers
Readout Positions A B C .300 [7.62] Card Slot Depth .350 [8.89] Card Slot Depth .415 [10.54] Card Slot Depth
.670 [17.02] Tail Length (DIM “J”)
61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 1 2 C 6 D 0 6 P F 2 9 1 3 2 C 6 D 0 6 P F 2 9 0 4 2
3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 1 2 C 6 D 1 0 P F 2 9 1 3 2 C 6 D 1 0 P F 2 9 0 4 2
4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 1 2 C 6 D 1 2 P F 2 9 1 3 2 C 6 D 1 2 P F 2 9 0 4 2
5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 1 2 C 6 D 1 5 P F 2 9 1 3 2 C 6 D 1 5 P F 2 9 0 4 2
6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 1 2 C 6 D 1 8 P F 2 9 1 3 2 C 6 D 1 8 P F 2 9 0 4 2
7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 1 2 C 6 D 2 0 P F 2 9 1 3 2 C 6 D 2 0 P F 2 9 0 4 2
8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 1 2 C 6 D 2 2 P F 2 9 1 3 2 C 6 D 2 2 P F 2 9 0 4 2
9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 1 2 C 6 D 2 5 P F 2 9 1 3 2 C 6 D 2 5 P F 2 9 0 4 2
1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 1 2 C 6 D 2 8 P F 2 9 1 3 2 C 6 D 2 8 P F 2 9 0 4 2
1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 1 2 C 6 D 3 0 P F 2 9 1 3 2 C 6 D 3 0 P F 2 9 0 4 2
1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 1 2 C 6 D 3 1 P F 2 9 1 3 2 C 6 D 3 1 P F 2 9 0 4 2
1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 1 2 C 6 D 3 5 P F 2 9 1 3 2 C 6 D 3 5 P F 2 9 0 4 2
1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 1 2 C 6 D 3 6 P F 2 9 1 3 2 C 6 D 3 6 P F 2 9 0 4 2
1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 1 2 C 6 D 4 0 P F 2 9 1 3 2 C 6 D 4 0 P F 2 9 0 4 2
1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 1 2 C 6 D 4 3 P F 2 9 1 3 2 C 6 D 4 3 P F 2 9 0 4 2
1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
.180 [4.57] Tail Length (DIM “J”)
61 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 P F 2 9 0 1 3 C 6 D 0 6 P F 2 9 1 3 3 C 6 D 0 6 P F 2 9 0 4 3
3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 P F 2 9 0 1 3 C 6 D 1 0 P F 2 9 1 3 3 C 6 D 1 0 P F 2 9 0 4 3
4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 P F 2 9 0 1 3 C 6 D 1 2 P F 2 9 1 3 3 C 6 D 1 2 P F 2 9 0 4 3
5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 P F 2 9 0 1 3 C 6 D 1 5 P F 2 9 1 3 3 C 6 D 1 5 P F 2 9 0 4 3
6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 P F 2 9 0 1 3 C 6 D 1 8 P F 2 9 1 3 3 C 6 D 1 8 P F 2 9 0 4 3
7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 P F 2 9 0 1 3 C 6 D 2 0 P F 2 9 1 3 3 C 6 D 2 0 P F 2 9 0 4 3
8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 C 6 D 2 2 P F 2 9 0 1 3 C 6 D 2 2 P F 2 9 1 3 3 C 6 D 2 2 P F 2 9 0 4 3
9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 P F 2 9 0 1 3 C 6 D 2 5 P F 2 9 1 3 3 C 6 D 2 5 P F 2 9 0 4 3
1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 P F 2 9 0 1 3 C 6 D 2 8 P F 2 9 1 3 3 C 6 D 2 8 P F 2 9 0 4 3
1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 P F 2 9 0 1 3 C 6 D 3 0 P F 2 9 1 3 3 C 6 D 3 0 P F 2 9 0 4 3
1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 P F 2 9 0 1 3 C 6 D 3 1 P F 2 9 1 3 3 C 6 D 3 1 P F 2 9 0 4 3
1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 P F 2 9 0 1 3 C 6 D 3 5 P F 2 9 1 3 3 C 6 D 3 5 P F 2 9 0 4 3
1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 P F 2 9 0 1 3 C 6 D 3 6 P F 2 9 1 3 3 C 6 D 3 6 P F 2 9 0 4 3
1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 P F 2 9 0 1 3 C 6 D 4 0 P F 2 9 1 3 3 C 6 D 4 0 P F 2 9 0 4 3
1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 P F 2 9 0 1 3 C 6 D 4 3 P F 2 9 1 3 3 C 6 D 4 3 P F 2 9 0 4 3
1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
149
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Press-Fit Application Tooling
BMEP 1K/2K Servo Electric
Press
• 1000 or 2000 lb force [4.5
or 9 kN]
• 12” [305 mm] throat depth
• Compact footprint – 16” x
24” [406 x 610 mm]
• Force resolution of
approximately 1 lb [4.4 N]
for delicate press applica-
tions.
Tyco Electronics offers a
complete line of servo-elec-
tric driven presses for the
application of press-fit con-
nectors. Each system fea-
tures a PC controlled servo
electric drive for precise
application and monitoring
of force, speed, and press
height. The entire process
is data driven to provide
flexible programming and
automatic set-up. SPC
analysis is provided for
each connector pressed to
assure the quality of every
application. BMEP 3T/5T Benchtop Electric
Servo Press
• 3 or 5 tons force [27 or 44
kN]
• 18” x 24” [460 x 610 mm]
PCB capacity
• Compact footprint – 24” x
48” [610 x 1220 mm]
• Midrange force and board
size capacity in a bench-
top unit.
MEP 6T/12 T Manual Electric
Servo Press
• 6 or 12 tons force [53 or
107 kN]
• 24” x 36” [610 x 914 mm]
PCB capacity
• Self-contained, portable
unit
• Compact, manual unit
capable of handling large
boards and high force
applications.
Automatic Pick, Place and
Press (AP3)
• 8 tons force [71 kN]
• 18” x 30” [457 x 762 mm]
PCB capacity
• SMEMA compatible unit
for automatic pick, place
and press of connectors
and odd-from compo-
nents.
• Vision system for pin
inspection prior to place-
ment.
150
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Press-Fit Card Edge Insertion Tools
Ordering Information
Center-to Connector Max. No. Of Tool Part Replacement Blade
Center Prefix Positions Number Part Number
Acquired P/N TYCO Acquired P/N Tyco
.100 x .100 C1 70 98336 3-1437266-5 98293 1437274-1
2.54 x 2.54
.100 x .100 C1 100 98341 98293 1437274-1
2.54 x 2.54
.156 x .200 C6 43 98231 1-1437266-1 98206 1437266-8
3.96 x 5.08
.125 x .250 C7 50 98230 1-1437266-0 98206 1437266-8
3.18 x 6.35
.100 x .200 C8 70 98224 1-1437266-9 98206 1437266-8
2.54 x 5.08
.100 x .200 W8 70 98236 1-1490560-1 98238 1490563-12.54 x 5.08
(Full Scoop)
.100 x .200 W8 35 98236 1-1490560-2 98238 1490563-12.54 x 5.08
(Full Scoop)
151
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Press-Fit Card Edge Removal Tool Kits
Description
Removal tool kits include:
impact tools, removal tips
for tail lengths ranging from
.180 in. [4.57] to .680 in.
[17.27] Kits for .100" x .200"
[2.54 x 5.08] Series Card
Edge connectors include
the insertion tip.
Acquired Tyco
Center x Row Prefix Kit Number Kit Number
.156 x .200 C6 9818002 1437266-3
3.96 x 5.08
.125 x .250 C7 9818002 1437266-3
3.18 x 6.35
.100 x .200 C8 9818002 1437266-3
2.54 x 5.08
.100 x .100 C1 9818004 1437266-4
2.54 x 2.54
.100 x .200 W8 9818005 1437266-5
2.54 x 5.08
Wide Full Scoop
R e p l a c e m e n t T y c o
I t e m D e s c r i p t i o n Applies to Kit No. P a r t P a r t
N o . 9 8 1 8 0 0 1 9 8 1 8 0 0 1 9 8 1 8 0 0 3 9 8 1 8 0 0 4 9 8 1 8 0 0 5 N u m b e r N u m b e r
1Impact Tool √√√√√9 8 2 0 4 0 1 1 4 3 7 2 6 6 - 7
2Removal Tip - .180 [4.57] Tail √√√√√9 8 2 0 3 0 1 1 4 3 7 2 6 6 - 6
3Removal Tip - . 3 7 8 / . 4 7 5 T a i l √√√√9 8 2 0 3 0 2 1 4 3 7 2 6 0 - 4
9 . 6 0 / 1 2 . 0 7
4Removal Tip - . 6 7 0 / . 6 8 0 T a i l √√√√9 8 2 0 3 0 3
1 7 . 0 2 / 1 7 . 2 7
6Insertion Tip - C6, 7 & 8 PF 9 8 3 6 7 0 1 3 - 1 4 3 7 2 6 6 - 9
1 0 Removal Tip - . 5 5 0 / . 6 2 5 T a i l 9 8 2 0 3 0 5 1 4 3 7 2 6 0 - 5
1 3 . 9 7 / 1 5 . 8 8
1 1 Insertion Tip - C1 Series PF 9 8 3 6 3 0 1 1 4 3 7 2 6 0 - 6
1 2 Insertion Tip - W8 Series PF 9 8 3 6 7 0 2 1 4 3 7 2 6 0 - 7
Ordering Information
Ordering Information
152
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Wire-to-Board Connectors
Except for DUO-TYNE flag
connectors, which are
exclusively for wire-to-board
application, the connectors
presented in this section
are primarily wire-to-board
connectors, but do have
some board-to-board capa-
bilities. These connectors
are available in a wide
range of styles to suit
almost any wire-to-board
application. This versatile
connector family features
snap-in contacts of various
configurations including
crimp, post, eyelet and
solder types.
Wire-to-board crimp,
snap-in contacts are easily
inserted into the connector
housing and are furnished
in reel-fed strip form for
automatic machine applica-
tion and loose piece for
hand tool termination. The
Wire-to-Board Printed
Circuit Board Connector
family includes:
Crimp Snap Twin Leaf
Connectors
(Pages 154-163)
These connectors are
designed for high density
wire-to-board applications
and feature bifurcated,
crimp and solder eyelet
contacts on .100 [2.54] and
.125 [3.18] centers. Design
flexibility allows the cus-
tomer to save by purchas-
ing only enough contacts
for his circuit design
requirements. Contact
styles include crimp, solder
eyelet and vertical and
right-angle posts, in a
variety of sizes.
AMP-LEAF Connectors
(Pages 164-172)
These connectors are for
single- or double-sided
printed circuit boards.
Snap-in contacts lock in
place on .156 [3.96] cen-
ters, maintaining constant
pressure on circuit paths.
Contact options are avail-
able for precision crimped
terminations and solder dip
applications.
High Current Connectors
(Pages 173-176)
Designed for a current
capability of up to 30
amperes, these connectors
are an economical answer
to the costly problem of
interconnecting high current
printed circuitry. Styles are
available for wire-to-board
and board-to-board appli-
cations. Contacts are on
.312 [7.92] centers.
DUO-TYNE Flag Connectors
(Pages 177-180)
These economical connec-
tors are designed to meet
the quality and reliability
requirements of industries
such as appliance controls,
vending machine subasem-
blies, television, stereo,
business machines and
other areas with similar con-
trol needs. The right-angle
design of the connector
permits close-quarter
cabling. Contacts are
doubly locked in when
a PC board is inserted.
153
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Wire-to-Board Connector Selection Guide
.340 [8.64]
.350 [8.89]
.360 [9.14]
.375 [9.53]
.437 [11.10]
.485 [12.32]
.087
[2.21]
.375
[9.53]
.700
[17.78]
AMP-LEAF
Connectors
(Pages 164-172)
High Current
Connectors
(Pages 173-176)
.567
[14.40]
.967
[24.56]
.437
[11.10]
Centerlines
.100 [2.54] X
.125 [3.18] X
.156 [3.96] X X
.197 [5.00]
.260 [6.60]
.312 [7.92]
Styles
Crimp X X
Right-Angle Post X X
Wrap-Type Post X X
Solder Eyelet X X
Solder Tail X X
Double Sided X X
Single Sided X X
DUO-TYNE Flag
Connectors
(Pages 177-180)
.200
[5.08]
.500
[12.70]
.240
[6.10]
.375
[9.53]
.012
[0.30]
.578
[14.68]
Centerlines
.100 [2.54]
.125 [3.18]
.156 [3.96] X
.197 [5.00]
.260 [6.60]
.312 [7.92] X
Styles
Crimp X X
Right-Angle Post
Wrap-Type Post
Solder Eyelet
Solder Tail X
Double Sided X X*
Single Sided
*Double-sided board; single readout.
.350 [8.89]
.437 [11.10]
.175
[4.45]
.405
[10.29]
.750
[19.05]
Crimp Snap
Twin Leaf Connectors
(Pages 154-163)
154
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Crimp Snap Twin Leaf Connectors
Product Facts
Crimp snap-in, solder eye-
let, .025 [0.64] square
posted and right angle
contacts on .100 [2.54],
.125 [3.18] or .156 [3.96]
centers
Customer buys only enough
contacts to meet circuit and
retention requirements
Contacts bifurcated for
redundancy
Single leaf version avail-
able for higher contact
normal forces
Low insertion forces
Accommodates AWG 16-28
[1.4-0.08 mm2] wire range
and insulation diameters
.035-.105 [0.89-2.67]
Large variety of connector
sizes
Cavity identification on face
of card slot and wire entry
High speed automatic
machine terminations
provide uniform reliability
at lowest applied cost
Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
Certified by Canadian
Standards
Association
File No. LR 7189
The Crimp Snap Twin Leaf
Connector is designed
especially for high density
wire-to-board applications.
Termination styles include
crimp, solder, posted and
right angle, in a variety of
s i z e s .
Performance Specifications
Contact Rating*: 5 amperes,
continuous 3 amperes, max. (for .025
[0.64] posted contacts)
Contact Resistance:
10 milliohms, max.
Insulation Resistance:
5000 megohms (initial)
1000 megohms
Voltage Rating:
.100 [2.54] Centerline-1000 Vrms
.125 [3.18] Centerline-1500 Vrms
.156 [3.96] Centerline-1800 Vrms
Insertion Force (per pair): Twin
Leaf-10 oz. [2.78 N], max.; 7.6 oz.
[2.11 N], avg. Non-Bifurcated Contacts-
20 oz. [5.57 N], max.
Extraction Force (per pair): Twin
Leaf-0.7 oz. [0.195 N], min.; 1.2 oz.
[0.334 N], avg.
Operating Temperature:
-55°C to +105°C
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
Design flexibility allows the
customer to save by pur-
chasing only enough
contacts for the circuit
requirements. Easy replace-
ability of each contact cuts
repair cost in the event of
contact or wire damage.
155
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Crimp Snap Twin Leaf Connectors (Continued)
Material and Finish:
Phosphor bronze, plated .000030
[0.00076] nickel on entire contact, with
the addition of one of the following
platings:
Plating A—.000030 [0.00076] gold in
mating area
Plating B—.000015 [0.00038] gold in
mating area
Plating C—.000050 [0.00127] gold in
mating area, with gold flash on remain-
der of contact
Plating D—.000015 [0.00038] gold in
mating area, with gold flash on remain-
der of contact
Note: Tin plating is available upon
request.
Related Product Data:
Performance Specifications
page 154
Application Tooling—pages 184,185
Connector Housings—pages 157,
159, 161
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheets
408-7527, 408-7529, 408-7531,
408-7551, 408-7556, 408-7583
Note: Only loose piece contacts
manufactured and supplied by Tyco
Electronics are to be used with the
hand tools listed on this page. No
attempt should be made to produce
loose piece parts from a strip since
special cutoff tooling is required to
assure a properly functioning part.
Wire Size C o n t a c t Contact Part Numbers Applicator for Applicator for
C o n n e c t o r R a n g e I n s u l a t i o n F i n i s h A M P - O - L E C T R I C S t r i p p e r / C r i m p e r C o l o r H a n d
C e n t e r l i n e A W G / m m2Dia. Range ( P l a t i n g ) Loose Piece Strip Form M a c h i n e * M a c h i n e C o d e T o o l
A 583616-4 583616-2
28-24 .035-.055 B 583616-5 583616-3
0.08-0.2 0.89-1.40 C 583616-9 583616-8 466577-4 466912-1 Orange 90268-1
.100 D 1-583616-1 1-583616-0
2.54 A 583853-5 583853-3
24-20 .048-.060 B 583853-4 583853-2
0.2-0.6 1.22-1.52 C 583853-9 583853-8 466622-2 466919-1 Green 91535-1
D 1-583853-1 1-583853-0
A 583616-4 583616-2
28-24 .035-.055 B 583616-5 583616-3
0.08-0.2 0.89-1.40 C 583616-9 583616-8 466577-4 466912-1 Orange 90268-1
D 1-583853-1 1-583853-0
A 583853-5 583853-3
24-20 .048-.060 B 583853-4 583853-2
.125 0.2-0.6 1.22-1.52 C 583853-9 583853-8 466622-2 466919-1 Green 91535-1
3.18 D 1-583853-1 1-583853-0
A 583649-6 583649-3
22-18 .049-.095 B 583649-5 583649-2 466713-2 466928-1 Violet 90264-1
0.3-0.9 1.24-2.41 C 583649-7 583649-4
20-16 .073-.090 A 583875-6 583875-5
0.6-1.4 1.85-2.29 C 583875-3 583875-2 687775-2 White 90285-1
A 583616-4 583616-2
28-24 .035-.055 B 583616-5 583616-3
0.08-0.2 0.89-1.40 C 583616-9 583616-8 466577-4 466912-1 Orange 90268-1
D 1-583616-1 1-583616-0
A 583853-5 583853-3
24-20 .048-.060 B 583853-4 583853-2
0.2-0.6 1.22-1.52 C 583853-9 583853-8 466622-2 466919-1 Green 91535-1
.156 D 1-583853-1 1-583853-0
3.96 A 583649-6 583649-3
22-18 .049-.095 B 583649-5 583649-2 466713-2 466928-1 Violet 90264-1
0.3-0.9 1.24-2.41 C 583649-7 583649-4
.073-.090 A 583875-6 583875-5
20-16 1.85-2.29 C 583875-3 583875-2 687775-2
0.6-1.4 .085-.105 White 90285-1
2.16-2.67 B 583875-3 vvv
Wire Size C o n t a c t Contact Part Numbers Applicator for Applicator for
C o n n e c t o r R a n g e I n s u l a t i o n F i n i s h A M P - O - L E C T R I C S t r i p p e r / C r i m p e r C o l o r H a n d
C e n t e r l i n e A W G / m m2Dia. Range ( P l a t i n g ) Loose Piece Strip Form M a c h i n e * M a c h i n e C o d e T o o l
28-24 .035-.055
.100 0.08-0.2 0.89-1.40 A 531476-5 531476-4 466577-4 466912-1 Orange 90268-1
2.54 24-20 .048-.060 A 531477-5 531477-4
0.2-0.6 1.22-1.52 B 531477-4 531477-2 466622-2 466919-1 Green 91535-1
28-24 .035-.055
0.08-0.2 0.89-1.40 A 531476-5 531476-4 466577-4 466912-1 Orange 90268-1
.125 24-20 .048-060 A 531477-5 531477-4
3.18 0.2-0.6 1.22-1.52 B 531477-3 531477-2 466622-2 466919-1 Green 91535-1
22-18 .045-.095
0.3-0.9 1.14-2.41 A 531478-4 466713-2 466928-1 Violet 90264-1
28-24 .035-.055 A 531476-5 531476-4
0.08-0.2 0.89-1.40 B 531477-5 466577-4 466912-1 Orange 90268-1
.156 24-20 .048-.060 A 531477-5 531477-4
3.96 0.2-0.6 1.22-1.52 B 531477-3 531477-2 466622-2 466919-1 Green 91535-1
22-18 .045-.095
0.3-0.9 1.14-2.41 A 531478-4 466713-2 466928-1 Violet
*Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench
machines and lead-making machines.
.705
[17.91]
.705
[17.91]
.104
[2.64]
.030
[0.76]
.104
[2.64]
.030
[0.76]
.705
[17.91]
.060
[1.52]
.705
[17.91]
.060
[1.52]
Crimp, Snap-In Contacts
Material and Finish:
Phosphor bronze, plated .000030
[0.00076] nickel on entire contact, with
the addition of one of the following
platings:
Plating A—.000030 [0.00076] gold in
mating area
Plating B—.000015 [0.00038] gold in
mating area
Note: Tin plating is available upon
request.
Related Product Data:
(See above)
Crimp, Snap-In Contacts,
Non-Bifurcated
156
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Crimp Snap Twin Leaf Connectors (Continued)
Material and Finish:
Phosphor bronze, plated .000030
[0.00076] nickel on entire contact, with
the addition of one of the following
platings:
Plating A—.000030 [0.00076] gold in
mating area
Plating B—.000015 [0.00038] gold in
mating area
Solder eyelet portion is tin plated.
Note: Tin plating of entire contact is
available upon request.
Related Product Data:
Performance Specifications
page 154
Connector Housings—pages 157,
159, 161
Technical Documents
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheets 408-7527,
408-7529
Snap-In Solder Eyelet
Contacts
Material and Finish:
Contact—Phosphor bronze, plated
.000015 [0.00038] gold in mating area,
with entire contact underplated .000030
[0.00076] nickel
Post—Phosphor bronze, tin-plated
Note: Tin plated contacts are avail-
able upon request.
Related Product Data:
Performance Specifications
page 154
Connector Housings—pages 157,
159, 161
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheets 408-7527,
408-7529
Snap-In Wrap Post
Contacts
Contact
Connector Finish Part
Centerline (Plating) Numbers
.100 A 583854-3
2.54 B 583854-5
.125
3.18 A 530245-3
Connector Dimension Part
Centerline
Spacing L Numbers
.451
.100 11.46 583879-1
2.54 .535
13.59 583879-4
.125 .525
3.18 13.34 583884-1
.156 .525
3.96 13.34 583884-1
.104
[2.64]
.030
[0.76]
.060
[1.52]
.025 [0.64] Square
L
Hand Tool Contact Extraction Tool
157
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Crimp Snap Twin Leaf Connectors, .100 [2.54] Centerline
No. of Dimensions Part Numbers
Dual Without With
Positions A B C D E Mounting Ears Mounting Ears
2-583717-1
6.700 .900 .720 1.175 1.430
17.78 22.86 18.29 29.85 36.32 1-583861-5
.800 1.000 .820
720.32 25.4 20.83 2-583717-3
.900 1.100 .920
822.86 27.94 23.36 3-583717-9
1.700 2.100
1.100 1.300 1.120 43.18 53.34 1-583717-1 1-583718-1
10 27.94 33.02 28.49 1.575 1.830
40.01 46.48 1-583861-7
1.200 1.400 1.600
13 30.48 35.56 40.64 3-583717-3
1.500 1.700 1.520
14 38.1 43.16 38.61 2-583717-7
2.200 2.600
1.600 1.800 1.620 55.88 66.04 1-583717-3 1-583718-3
15 40.64 45.72 41.15 2.075 2.330
52.71 59.18 1-583861-9
1.800 2.000 1.820 2.400 2.800
17 45.72 50.8 46.30 60.96 71.12 1-583717-5 1-583861-1
1.900 2.100 1.920
18 48.26 53.34 48.76 1-583717-7
2.100 2.300 2.120
20 53.34 58.42 53.84 3-583717-1
2.300 2.500 2.320 2.900 3.300
22 58.42 63.50 58.93 73.66 83.82 1-583717-9 1-583718-9
2.600 2.800 2.620 3.200 3.600
25 66.04 71.12 66.55 81.28 91.44 1-583717-1 1-583718-1
3.700 4.100
3.100 3.300 3.120 93.98 104.14 1-583717-3 1-583718-3
30 78.74 83.82 79.25 3.575 3.830
90.81 97.28 1-583861-1
3.300 3.500 3.320 3.900 4.300
32 83.82 88.90 84.33 99.06 190.22 2-583718-7
3.700 3.900 3.720 4.175 4.430
36 93.98 93.06 94.49 106.04 112.52 2-583861-5
4.700 5.100
4.100 4.300 4 .120 119.38 129.54 1-583718-5
40 104.14 109.22 104.65 4.575 4.830
116.21 122.68 1-583861-3
5.700 6.100
5.100 5.300 5.120 144.78 154.94 1-583717-9 1-583718-7
50 129.54 134.62 130.05 5.575 5.830
141.61 148.08 2-583861-1
Material: Black glass-filled polyester,
94V-O rated
Related Product Data:
Performance Specifications
page 154
Contacts—pages 155, 156
Accessories—page 162*
PCB Edge Pattern—page 163
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheet 408-7527
.128
[3.25]
Dia.
2 Holes
.100
[2.54] .100
[2.54]
.300
[7.62]
.350
[8.89]
.175
[4.45]
.750
[19.05]
.550
[13.97]
.345
[8.76]
.250
[6.35]
A
D
E
B
CC
A
B
.100
[2.54] .100
[2.54]
.350
[8.89]
.400
[10.16]
.750
[19.05]
Fit for
.055-.070
[1.40-1.78]
PC Board
Fit for
.055-.070
[1.40-1.78]
PC Board
With Mounting Ears Without Mounting Ears
Note: Other connector sizes can be made available, consult Tyco Electronics.
H o u s i n g s
158
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Crimp Snap Twin Leaf Connectors, .100 [2.54] Centerline (Continued)
Note: Other connector sizes can be made available, consult Tyco Electronics.
.350
[8.89] .300
[7.62]
.100
[2.54] .100
[2.54]
.100
[2.54] Typ.
.125
[3.17]
.550
[13.97]
.750
[19.05]
.750
[19.05]
.400
[10.16]
.038
[0.97]Dia. Typ.
.128
[3.25]Dia.
(2 Plcs.)
.345
[8.76]
.350
[8.89]
.170
[4.32]
.250
[6.35]
AA
BB
G
C
F
Min.
E
C
D
D
E
A
C
Connector Centerline
Spacing
B
Intercontact
Keying Slot Typ.
.150
[3.81]
With Mounting Ears
Type I Type II Recommended PC Board Hole Layout
Without Mounting Ears
Material and Finish:
Housing—Black glass-filled polyester,
94V-O rated
Contacts—Phosphor bronze, plated
.000015 [0.00038] gold in mating area,
with entire contact underplated .000030
[0.00076] nickel
Posts—Phosphor bronze, tin plated
Related Product Data:
Performance Specifications
page 154
Asccessories—page 162*
PCB Edge Pattern and Hole
Layout—page 163
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheet 408-7527
Housings Preloaded with
Right-Angle Posts
Posted Assembly Part Numbers
No. of D i m e n s i o n s Right-Angle Post Right-Angle Post
D u a l With Mounting Ears W i t h o u t
P o s . A B C D E F G Type I Type II Mounting Ears
1.100 1.300 1.120 1.575 1.830
10 27.94 33.02 28.49 40.01 46.48 1-583900-5
1.800 2.000 1.820 .090 .150
17 45.72 50.80 46.23 2.29 3.81 1-530218-5
2.300 2.500 2.320 2.900 3.300 .090 .150
22 58.42 63.50 58.93 73.66 83.82 2.29 3.81 1-583900-3 1-530218-9
2.600 2.800 2.620 3.200 3.600 .090 .150
25 66.04 71.12 66.55 81.28 91.44 2.29 3.81 583900-1 1-530218-1
2.900 3.100 2.920 3.375 3.630 .090 .150
28 73.66 78.74 74.16 85.72 92.20 2.29 3.81 2-583900-6
3.100 3.200 3.120 3.700 4.100 .090 .150
30 78.74 81.28 79.25 93.98 104.14 2.29 3.81 1-583900-4 1-530218-6
5.100 5.300 5.120 5.575 5.830
50 129.54 134.62 130.05 141.61 148.08 583900-3
.128
[3.25] Dia.
Typ.
.100
[2.54]Typ.
Fit for
.055-.070
[1.40-1.78]
PC Board
.025
[.064]
Square Post
Tin-Plated
159
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Crimp Snap Twin Leaf Connectors, .125 [3.18] Centerline
With Mounting Ears Without Mounting Ears
Fit for
.055-.070
[1.40-1.78]
PC Board
Fit for
.055-.070
[1.40-1.78]
PC Board
.125
[3.18]
.125
[3.18]
.300
[7.62]
.218
[5.54]
.437
[11.10]
.125
[3.18]
.125
[3.18]
.345
[8.76]
.550
[13.97]
.750
[19.05] .750
[19.05]
.345
[8.76]
.250
[6.35]
.437
[11.10]
.300
[7.62]
.455
[11.56]
A
E
A
D
B
CC
B
.128
[3.25] Dia.
2 Holes
Material: Black glass-filled polyester
94V-O rated
Related Product Data:
Performance Specifications
page 154
Contacts—pages 155, 156
Accessories—page 162
PCB Edge Pattern—page 163
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheet 408-7527
Housings
No. of Dimensions Part Numbers
Dual Without With
Positions A B C D E Mounting Ears Mounting Ears
.875 1.035 .845 1.295 1.555
622.23 26.29 21.46 32.89 39.50 1-583873-1 1-583864-1
1.375 1.535 1.345 1.795 2.055
10 34.93 38.99 34.16 45.59 52.20 1-583864-3
2.000 2.160 1.970 2.420 2.680
15 50.80 54.86 50.04 61.47 68.07 1-583873-5
2.875 3.035 2.845 3.295 3.555
22 73.03 77.09 72.26 83.69 90.30 1-583873-9 1-583864-9
3.250 3.410 3.220 3.670 3.930
25 82.55 86.61 81.79 93.22 99.82
3.625 3.785 3.595 4.045 4.305
28 92.08 96.14 91.31 102.74 109.35 1-583864-3
3.875 4.035 3.845 4.295 4.555
30 98.43 102.49 47.66 109.09 115.70 2-583864-1
5.125 5.285 5.095 5.545 5.805
40 130.17 134.23 129.41 140.84 147.44 1-583864-7
5.625 5.785 5.595 6.045 6.305
44 142.88 146.94 142.11 153.54 160.15 1-583873-9
Note: Other connector sizes can be made available, consult Tyco Electronics.
160
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Crimp Snap Twin Leaf Connectors, .125 [3.18] Centerline (Continued)
Fit for
.055-.070
[1.40-1.78]
PC Board
.750
[19.05]
.345
[8.76]
.170
[4.32]
.100
[2.54]
.150
[3.81]
.180
[4.57]Min.
.125
[3.18]
.125
[3.18]
4.035
[102.49]
4.555
[115.70] 4.295
[109.09]
3.845
[97.66]
.128
[3.25]Dia.
.125
[3.18]Typ.
.300
[7.62]
3.875
[98.43] .128
[3.25] Dia.
Typ.
.025
[0.64]
Square Post
Tin-Plated
With Mounting Ears
Material and Finish:
Housing—Black glass-filled
polyester, 94V-O rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold in mating area,
with entire contact underplated .000030
[0.00076] nickel
Posts—Phosphor bronze, tin-plated
Related Product Data:
Performance Specifications
page 154
Accessories—page 162
PCB Edge Pattern and Hole
Layout—page 163
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheet 408-7527
Housings Preloaded with
Right-Angle Posts
30 Dual Positions,
Part No. 530238-8
.437±.007
[11.10±0.18]
.550
[13.97]
.250
[6.35]
161
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Crimp Snap Twin Leaf Connectors, .156 [3.96] Centerline
Material: Black glass-filled poly-
ester, 94V-O rated
Related Product Data:
Performance Specifications
page 154
Contacts—pages 155, 156
Accessories—page 162
PCB Edge Pattern—page 163
Technical Documents:
(pages 186, 187):
Product Specification
108-9031
Application Specification
114-9004
Instruction Sheet 408-7527
Housings
No. of Dimensions Part Numbers
Dual Mounting
Positions A B C D E Ears
1.100 1.264 .976 1.535 1.785
627.94 32.11 24.79 38.99 45.34 1-583859-3
1.412 1.576 1.288 1.847 2.097
835.86 40.03 32.72 46.91 53.26 2-583859-1
1.724 1.888 1.600 2.159 2.409
10 43.79 47.96 40.64 54.84 61.19 1-583859-9
2.036 2.200 1.912 2.471 2.721
12 51.71 55.88 48.56 62.76 69.11 1-583859-5
2.504 2.668 2.380 2.939 3.189
15 63.60 67.77 60.45 74.65 81.00 1-583859-7
2.972 3.136 2.848 3.407 3.657
18 75.49 79.55 72.34 86.54 92.89 1-583859-5
3.596 3.760 3.472 4.031 4.281
22 91.34 95.50 88.19 102.39 108.74 1-583859-3
4.532 4.696 4.408 4.967 5.217
28 115.11 119.28 111.96 126.16 132.51 1-583859-1
5.780 5.944 5.656 6.215 6.465
36 146.81 150.96 143.66 157.86 164.21 2-583859-3
Note: Other connector sizes can be made available, consult Tyco Electronics.
With Mounting Ears
Fit for
.055 - .070
[1.40-1.78]
PC Board
.160
[4.06] .156
[3.96]
.437
[11.10]
.128
[3.25]Dia.
2 Holes
.325
[8.26]
.162
[4.11]
.750
[19.05]
.455
[11.56]
.250
[6.35]
.345
[8.76]
A
D
E
B
C
162
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Accessories for Crimp Snap Twin Leaf Connectors
.062
[1.57]
PC Board Ref.
Mounting
Block
Card Extender
C o n n e c t o r
Housing Ref. #5 Self
Tapping
Screws
Dummy Contacts
Material: Phosphor bronze
Retaining Spring
Material: Stainless steel
Mounting Block
Material: Natural color nylon
Locking Key
Material: Nylon
Keying Plugs
Tin Plated — Part No. 583857-5
.000030 [0.00076] Nickel Plated — Part No. 583857-6
Gold Flash-Over-Nickel Plate— Part No. 583857-7
Unplated— Part No. 583691-2
Gold Flash-Over-Nickel Plate— Part No. 583691-3
Intercontact Plug
Natural Nylon— Part No. 583274-1
Glass-Filled Polyester— Part No. 583274-3
On-Contact Plug
Natural Nylon— Part No. 583764-1
On-Contact Clip
Part No. 530213-1
.062
[1.57] Dia.
Roll Pin
Related Product Data:
The dummy contact is used in sparsely
loaded housings to balance contact
pressure. For specific recommendations,
consult Tyco Electronincs.
Technical Documents
(pages 186, 187):
Instruction Sheet 408-7527
Related Product Data:
Retaining springs are used for single
sided PC board applications. Use one
spring per 6 empty cavities.
Technical Documents
(pages 186, 187):
Instruction Sheet 408-7527
Technical Documents
(pages 186, 187):
Instruction Sheet 408-7527
Kit Part No. 531250-4
Each kit includes 2 mounting blocks
2 self tapping screws,
#5 x .437 [11.10]
2 roll pins
.075 x .250 [1.57 x 6.35]
163
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Crimp Snap Twin Leaf Connectors (Continued)
.062
[1.57]
.078
[1.98]
45°Chamfer
45°Chamfer
.015
[0.38]
B
Min.
A
Hole for
Locking Key
.420
[10.67]
Recommended PC Board
Edge Pattern
Recommended PC Board
Hole Layout
.038
[0.97]Dia. Typ.
.128
[3.25]Dia.
(2 Plcs.)
D
E
A
C
Connector Centerline
Spacing
B
No. of Dimensions
Dual
Positions A B C D E
.900 .625 .475 1.575 .400
10 22.86 15.88 12.07 40.01 10.16
1.600
17 40.64
1.900 .625 .375 2.575 .337
20 48.26 15.88 9.53 65.41 8.56
2.100 .625 4.75 2.900 .337
22 53.34 15.88 12.07 73.66 8.56
2.400 .625 .475 3.200 .400
25 60.96 15.88 12.07 81.28 10.16
2.900 3.700 .400
30 73.66 93.98 10.16
4.900 .525 .375 5.575 .337
50 124.46 13.34 9.53 141.61 8.56
No. of Dimensions
Dual
Positions A B C D E
3.625 4.295 .350
30 92.08 109.09 8.89
Connector Centerline Spacing: .125 [3.18]
Connector Centerline Spacing: .100 [2.54]
Connector Dimensions
Centerline
Spacing A B
.100 .093 .052
2.54 2.36 1.32
.125 .118 .078
3.18 3.00 1.98
.156 .153 .094
3.96 3.89 2.39
164
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors
Product Facts
Contacts on .156 [3.96]
centers
Glass-filled polyester,
phenolic or diallyl phthalate
housings
Closed card entry design
helps prevent overstressing
of contacts
Gold-over-nickel plated
contacts
Locking lance permits easy
contact replacement
Keying
Contacts maintain exact
pressures on the circuit
paths, despite repeated
insertions and extractions
Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
Certified by Canadian
Standards
Association**,
File No. LR 7189
Performance Specifications
Contact Current Rating*:
5.0 amperes, max.
Contact Engaging Force:
16 oz. [4.4 N], max.
Contact Separation Force:
2 oz. [0.6 N], min.
Vibration:
MIL-STD-202, Method 201
Operating Temperature:
Contacts –40°C to +85°C
Storage Temperature:
–40°C to +85°C
Right-angle posted connec-
tors are supplied in various
sizes, with preloaded con-
tacts on one or both sides.
The solder-type posts are
formed 90° from the housing
to permit right-angle inter-
facing between mother and
daughter boards.
AMP-LEAF Connectors are
available with crimp, snap-in
contacts or preloaded with
right-angle posted contacts.
The crimp type printed cir-
cuit connector is supplied
with the housing unloaded—
the user buys only enough
contacts to satisfy circuit
requirements. This feature,
when coupled with the Tyco
Electronics matched tooling,
contributes substantially to
lower installed costs.
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
**CSA certification pending for
certain products, as noted.
Housings:
Glass-Filled Polyester, –55°C to
+105°C
Glass-Filled Phenolic, –65°C to +125°C
Diallyl Phthalate, –65°C to +125°C
165
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors (Continued)
Material and Finish:
Phosphor bronze, plated as follows:
Plating A—.000100-.000200
[0.00254-0.00508] tin (lubricant must
be used)
Plating B—.000030 [0.00076] min.
gold in mating area, gold flash on
remainder of contact, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating C—.000015 [0.00038] min.
gold in mating area, gold flash on
remainder of contact, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating D—.000030 [0.00076] min.
gold over .000050 [0.00127] min. nickel
in mating area, remainder of contact
gold flash over .000015 [0.00038] min.
nickel
Plating E—.000030 [0.00076] min.
gold in mating area, with entire contact
underplated .000050 [0.00127] min.
nickel
Plating F—.000015 [0.00038] min.
gold in mating area, with entire contact
underplated .000050 [0.00127] min.
nickel
Related Product Data:
Performance Specifications
page 164
Connector Housings
pages 167-169
Application Tooling
pages 184, 185
Crimp, Snap-In Contacts
Material:
Phosphor bronze
Dummy Contact
Technical Documents:
(pages 186, 187):
Product Specifications
108-9013, 108-9043
Application Specification
114-9003
Instruction Sheets
408-6591, 408-7045, 408-7622,
408-7623, 408-7624, 408-7625,
408-7626
Crimp Inspection Sheet
CI 8050-33
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7037
C o n t a c t
W i r e Insulation Range Part Numbers C o n t a c t Applicator for H a n d
R a n g e S i n g l e D o u b l e L o o s e S t r i p F i n i s h A M P - O - L E C T R I C T o o l
A W G / m m2W i r e W i r e P i e c e F o r m M a c h i n e *
26-22 .050-.064 583990-3 583204-2 B
0.12-0.4 1.27-1.63 343371-1 D 466366-2 90028-3
583361-2 A
.120 583989-3 583361-3 B 90017-3 (1 #22-20)
22-18 .055-.080 3.05 583989-4 583361-4 C 466367-2 90028-3 (2 #22)
0.3-0.9 1.40-2.03 Max. 583555-4 E 90101-3 (1 #20)
583555-6 F
16 .108 .080-.160 90031-8 (2 #18)
1.25-1.40 2.74 2.03-4.06 583991-3 60151-6 B 466368-2 90101-3 (2 #20)
Max. 90101-3 (1 #16)
*Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench
machines and lead-making machines.
Notes: 1. Shorting contacts are available, consult Tyco Electronics.
Notes: 2. Contacts and housings to accommodate .093 [2.36] thick PC boards can be made available, consult Tyco
Electronics.
Contact Extraction Tool Extraction
Tool Used with
Number Housings
480110-2, -5
480142-2, -3
582140-5
582147-5
582264-2
582500-2
582963-2
583167-3
465195-1 583280-1
583617-1
583680-1
583685-1
583722-1
583723-1
583724-1
583725-1
583726-1
465195-2 480133-2
Plain Finish—
Part No. 66084-1
Tin Finish—
Part No. 66084-2
Gold Finish—
Part No. 66084-3
Wire Barrel Crimp
Terminal Stop
Locking Lance
Insulation Support
Hand Crimping Tool
166
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors (Continued)
Material and Finish:
Phosphor bronze, plated .000015
[0.00038] min. gold in contact area,
gold flash on remainder of contact, with
entire contact underplated .000050
[0.00127] min. nickel
Solder Eyelet Contact
Material and Finish:
Phosphor bronze, plated .000015
[0.00038] min. gold in contact area, tin
on post, with entire contact underplated
.000050 [0.00127] min. nickel
Post Type Contacts
Standard Eyelet Type Contact
Part No. 66067-5
(For .055-.070 [1.4-1.78]
Thick PC Boards)
Solder Dip Contact
Part No. 583294-2 (.000015)
Part No. 583294-1 (.000030)
(For .062 [1.57]
Thick PC Board)
.100
[2.54]
.120
[3.05]
.030
[0.76]
.185
[4.70]
L
.280
[7.11]
Locking Lance
Contact
Surfaces
Locking
Lance
Contact
Surfaces
Note: Solder tab will accommodate a maxi-
mum of two 16 AWG [1.25-1.4 mm2]
solid wires, or two 18 AWG [0.8-0.9
mm2] stranded wires.
Material and Finish:
Phosphor bronze, plated .000015
[0.00038] min. gold in contact area or,
plated .000030 [0.00076] min. gold in
contact area, tin on post, with entire
contact underplated .000050 [0.00127]
min. nickel
Solder Dip Contacts
For .052 [1.32]
Dia. Hole
.120
[3.05] Locking
Lance
Contact
Surfaces
Loose Piece
Post Contact Part No.
Length (.045 x .045
L [1.14 x 1.14]
Post)
.960
24.38 1-582355-3
.560
14.22 1-582355-5
Note: Post type contacts are for .055-.070 [1.4-1.78] thick PC boards.
167
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors, .156 [3.96] Centerline
Material: Glass-filled polyester
Related Product Data:
Card Guide Assembly—page 171
PC Board Thickness—.055-.070
[1.40-1.78]
Performance Specifications
page 164
Contacts—pages 165, 166
Accessories—page 171
PC Board Layout—page 172
Technical Documents:
(pages 186, 187):
Product Specifications
108-9013, 108-9043
Application Specification
114-9003
Instruction Sheet 408-7037
C
GH
D
.325 Card Slot
[8.26] Depth
.700
[17.78]
KJ
EDia.
(2 Holes)
F
B
.156
[3.96]
A
Glass-Filled Polyester
Housings
No. of Dimensions Housing
Dual Part
Positions A B C D E F G H J K Numbers
1.785 1.535 1.264 .976 .125 1.100 .456 .250 .300 .350
645.34 38.99 32.11 24.79 3.18 27.94 11.58 6.35 7.62 8.89 583722-1
2.409 2.159 1.888 1.600 .125 1.724 .456 .250 .300 .350
10 61.19 54.84 47.96 40.64 3.18 43.79 11.58 6.35 7.62 8.89 583723-1
2.721 2.471 2.200 1.912 .125 2.036 .456 .250 .300 .350
12 69.11 62.76 55.88 48.56 3.18 51.71 11.58 6.35 7.62 8.89 *583724-1*
3.189 2.939 2.668 2.380 .128 2.504 .456 .250 .300 .350
15 81.00 74.65 67.77 60.45 3.25 63.60 11.58 6.35 7.62 8.89 583680-1
3.657 3.407 3.136 2.848 .125 2.972 .456 .250 .300 .350
18 92.89 86.54 79.65 72.34 3.18 75.49 11.58 6.35 7.62 8.89 583725-1
3.657 3.407 3.136 2.848 .156 2.972 .456 .250 .300 .350
18 92.89 86.54 79.65 72.34 3.96 75.49 11.58 6.35 7.62 8.89 583725-3
4.281 4.031 3.760 3.472 .125 3.596 .456 .250 .300 .350
22 108.74 102.39 95.50 88.19 3.18 91.34 11.58 6.35 7.62 8.89 583617-1
4.281 4.031 3.760 3.472 .156 3.596 .456 .250 .300 .350
22 108.74 102.39 95.50 88.19 3.96 91.34 11.58 6.35 7.62 8.89 583617-3
4.749 4.499 4.228 3.940 .125 4.064 .456 .250 .300 .350
25 120.62 114.27 107.39 100.01 3.18 103.23 11.58 6.35 7.62 8.89 583726-1
5.529 5.279 5.008 4.720 .125 4.844 .456 .250 .300 .350
30 140.44 134.09 127.20 119.89 3.18 123.04 11.58 6.35 7.62 8.89 583685-1
7.015 6.578 5.942 5.722 .156 5.782 .455 .290 .325 .437
36 178.18 167.08 150.92 145.33 3.96 146.86 11.55 7.36 8.25 11.10 583552-1
*CSA certification pending.
Note: Other connector sizes can be made available, consult Tyco Electronics.
168
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors, .156 [3.96] Centerline (Continued)
Material: Glass-filled phenolic
per MIL-M-14F
Related Product Data:
Card Guide Assembly—page 171
Performance Specifications
page 164
Contacts—pages 165, 166
Accessories—page 171
PC Board Layout—page 172
Technical Documents:
(pages 186, 187):
Product Specifications
108-9013, 108-9043
Application Specification
114-9003
Instruction Sheet 408-7037
Glass-Filled Phenolic
Housings
A
B
D
F
.156
[3.96] JDia.
(2 Holes)
C
.700
[17.78]
E
GH
No. of Dimensions Housing
Dual Board Part
Positions A B C D E F G H J Thickness Numbers
1.982 1.767 1.550 1.410 1.288 .340 .250 .458 .125 .055-.070
850.34 44.88 39.37 35.81 32.72 8.64 6.35 11.63 3.18 1.40-1.78 582140-5
2.407 2.157 1.866 1.722 1.598 .360 .250 .456 .128 .055-.070
10 61.14 54.79 47.90 43.74 40.59 9.14 6.35 11.58 3.25 1.40-1.78 582963-2*
1.886 1.722 1.598 .360 .055-.070
10 47.90 43.74 40.59 9.14 ———1.40-1.78 583280-11
3.182 2.854 2.621 2.506 2.376 .350 .250 .466 .187 .055-.070
15 80.82 72.49 66.57 63.65 60.35 8.89 6.35 11.84 4.75 1.40-1.78 480110-5
3.182 2.854 2.621 2.506 2.376 .350 .250 .466 .125 .055-.070
15 80.82 72.49 66.57 63.65 60.35 8.89 6.35 11.84 3.18 1.40-1.78 1-582147-5*
3.182 2.933 2.621 2.506 2.376 .350 .250 .466 .128 .055-.070
15 80.82 74.49 66.57 63.65 60.35 8.89 6.35 11.84 3.25 1.40-1.78 1-582500-5
3.650 3.400 3.088 2.948 2.843 .375 .155 .406 .156 .055-.070
18 92.71 86.36 78.43 74.87 72.21 9.52 3.93 10.31 3.96 1.40-1.78 480133-5
4.274 4.025 3.754 3.591 3.466 .350 .250 .456 .125 .055-.070
22 108.56 102.24 95.35 91.21 88.04 8.89 6.35 11.58 3.18 1.40-1.78 480142-3
4.741 4.493 4.221 4.058 3.933 .350 .250 .456 .125 .055-.070
25 120.42 114.12 107.21 103.07 99.90 8.89 6.35 11.58 3.18 1.40-1.78 583167-3*
6.365 5.928 5.292 5.132 5.072 .485 .290 .455 .187 .084-.104
32 161.67 150.57 134.42 130.35 128.83 12.32 7.37 11.56 4.75 2.13-2.64 582264-22,3
*CSA certification pending.
1Housing without mounting ears.
2Housing does not accommodate intercontact keying plug.
3For .086 to .104 [2.18 to 2.64] thick PC boards (special contacts required).
Note: Other connector sizes can be made available, consult Tyco Electronics.
169
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors, .156 [3.96] Centerline (Continued)
Material: Diallyl phthalate
per MIL-M-14F
Related Product Data:
Card Guide Assembly—page 171
Performance Specifications
page 164
Contacts—pages 165, 166
Accessories—page 171
PC Board Layout—page 172
Technical Documents:
(pages 186, 187):
Product Specifications
108-9013, 108-9043
Application Specification
114-9003
Instruction Sheet 408-7037
Diallyl Phthalate
Housings
A
B
D
F
.156
[3.96]
JDia.
(2 Holes)
C
.700
[17.78]
E
GH
No. of Dimensions Housing
Dual Board Part
Positions A B C D E F G H J Thickness Numbers
3.187 2.859 2.625 2.510 2.380 .350 .250 .466 .187 .055-.070
15 80.95 72.62 66.68 63.75 60.45 8.89 6.35 11.84 4.15 1.40-1.78 480110-2
3.187 2.938 2.625 2.510 2.380 .350 .250 .466 .128 .055-.070
15 80.95 74.63 66.68 63.75 60.45 8.89 6.35 11.84 3.25 1.40-1.78 582500-2
3.656 3.406 3.093 2.953 2.848 .375 .155 .406 .156 .055-.070
18 92.86 86.51 78.56 75.01 72.34 9.53 3.94 10.31 3.96 1.40-1.78 480133-2
4.281 4.031 3.760 3.596 3.472 .350 .250 .456 .125 .055-.070
22 108.74 102.39 95.90 91.34 88.19 8.89 6.35 11.58 3.18 1.40-1.78 480142-2
Note: Other connector sizes can be made available, consult Tyco Electronics.
Single Slot Housing
170
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connectors, .156 [3.96] Centerline (Continued)
Material and Finish:
Housing—See chart below
Contacts—Phosphor bronze, plated
.000015 [0.00038] min. gold in mating
area, with entire contact underplated
.000050 [0.00127] min. nickel
Post—Phosphor bronze, tin plated
Retaining Spring—Stainless steel
Related Product Data:
Card Guide Assembly—page 171
Performance Specifications
page 164
Accessories—page 171
PC Board Layout—page 172
Technical Documents:
(pages 186, 187):
Product Specification
108-9013
Housings Preloaded with
Right-Angle Post Contacts
No. of Dimensions
Dual Part Housing
Positions A B C D E F G H J Numbers Material
2.407 2.157 1.886 1.722 1.598 .360 .700 .250 .456
10 61.14 54.79 47.9 43.74 40.59 9.14 17.78 6.35 11.58 583599-1*
3.182 2.933 2.621 2.506 2.376 .350 .700 .250 .466 Glass-Filled
15 80.82 74.5 66.57 63.65 60.35 8.89 17.78 6.35 11.84 583545-1* Phenolic
3.650 3.400 3.088 2.948 2.843 .375 .700 .250 .406
92.71 86.36 78.44 74.88 72.21 9.53 17.78 6.35 10.31 583544-1*
18 3.657 3.457 3.136 2.972 2.848 .350 .700 .250 .456 Glass-Filled
92.89 86.54 79.65 75.49 72.34 8.89 17.78 6.35 11.58 530851-1*Polyester
4.274 4.025 3.754 3.591 3.466 .350 .700 .250 .456 Glass-Filled
108.56 102.24 95.35 91.21 88.04 8.89 17.78 6.35 11.58 583458-2* Phenolic
22 4.281 4.031 3.760 3.596 3.472 .350 .700 .250 .456 Glass-Filled
108.74 102.39 95.50 91.34 88.19 8.89 17.78 6.35 11.58 583975-1* Polyester
5.270 4.961 4.680 4.527 4.402 .350 .700 .250 .456 Glass-Filled
28 133.86 126.01 118.87 114.99 111.81 8.89 17.78 6.35 11.58 530061-1* Phenolic
*CSA certification pending.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. Finished hole size is .048-.054 [1.22-1.37] diameter.
A
D
F
.156
[3.96]
B
C
G
E
HJ
.125
[3.18]
Dia.
(2 Holes)
.125
[3.18]
Post Contact
.022 x .036 [0.56 x 0.91]
Phosphor Bronze
Tin Plated
Phosphor Bronze
Selective Gold Plate
in Contact Area .000015
[0.00038] Gold
.150
[3.81]
.090
[2.29]
Min.
.156
[3.96]
.325
[8.26]
171
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connector Accessories
Material: Nylon
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7036,
408-7037, 408-7068, 408-7339
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7419
Keying Plugs
Material and Finish:
Beryllium copper, gold plated
Commoning Springs
Retaining Springs
Material: Stainless steel
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7035,
408-7037
Card Guides
Material: Glass-filled nylon, black
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7557,
408-7565
On-Contact Keying Plug Intercontact Keying Plugs
.055-.070 [1.4-1.78] Board Thickness—Part No. 480143-1
.040 [1.02] Wide—Part No. 582501-1
.025 [0.64] Wide—Part No. 583274-1
.055-.070 [1.4-1.78] thk. PC
board—Part No. 66092-1
.055-.070 [1.4-1.78] and
.084-.104 [2.13-2.64] thk. PC
board with locking latches—
Part No. 583454-1
Nickel Finish—Part No. 42973-1
Plain Finish—Part No. 42973-2
Gold Finish—Part No. 42973-3
Card Guide Part Number 583760-1
Note: Card guides may be used with all connector housings having mounting ears.
.093
[2.36] Dia.
.545
[13.84] Ref.
.076
[1.93]
.200
[5.08]
. 3 0 8
[ 7 . 8 2 ]
4.000
[101.6]
.240
[6.1]
.375
[9.52]
.250
[6.35]
Connector (Ref.)
.187
[4.75]
.135
[3.43] .245
[6.22]
172
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
AMP-LEAF Connector PC Board Layouts
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7037
Recommended
PC Board Layouts
.031
[0.79] Max.
Base Line A
.330
[8.38]
Min.
.050
[1.27] Min. B
.156
[3.96]
Note: Slot for intercontact keying may be
located between any two pads
(except the first two and last two
pads).
No. of Housing Dimensions
Positions Material A B
1.396 .152
8 P 35.46 3.86
1.709 .151
10 P 43.40 3.84
2.491 .153
DP 63.27 3.89
15 2.487 .152
P63.17 3.86
2.940 .144
18 DP 74.68 3.66
3.583 .153
DP 91.00 3.89
22 3.578 .151
P90.88 3.84
4.043 .150
25 P 102.69 3.81
5.117 .140
32 P 129.97 3.56
DP = Diallyl Phthalate
P = Phenolic
Note: Board thickness .055-.070 [1.4-1.78] all posi-
tions except 32 position–.084-.104 [2.13-2.64].
173
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
High Current Connectors
Product Facts
High current capability up to
30 amperes*
UL rated 94V-0 glass-filled
thermoplastic housings
Choice of wire-to-board and
board-to-board (solder tail)
connector configurations in
3, 4, 8, 9, 10 and 12 contact
sizes
Heavy duty contacts made
of high conductivity copper
alloy with tin-over-nickel
plating
Contacts on .312 [7.92]
centers
Large redundant areas of
contact provide excellent
electrical continuity
Connectors available for
mating with .062 [1.57],
.093 [2.36] and .125 [3.18]
thick double-sided PC
boards
Contacts furnished in strip
form for automatic machine
termination and loose form
for hand tool application
Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
Certified by Canadian
Standards
Association
File No. LR 7189
AMP High Current Edge
Connectors are an economi-
cal answer to the costly
issue of interconnecting
high current printed circuit-
ry. Designed for a current
capability of up to 30
amperes*, these connectors
feature UL rated 94V-0,
rugged glass-filled thermo-
plastic housings and high
conductivity copper alloy
contacts with bright tin-over-
nickel plating. Contacts are
on .312 [7.92] centers.
Connectors are available in
3, 4, 8, 9, 10 and 12 contact
positions and in a choice of
two styles for board-to-
board and wire-to-board
a p p l i c a t i o n s .
The board-to-board connec-
tors are supplied preloaded
with solder tail contacts and
are designed to mate with
.062 [1.57] thick double-
sided daughter boards.
Performance Specifications
Contact Current Rating*:
30 amperes, max.
Dielectric Withstanding Voltage
(Sea Level):
1800 VAC
Operating Voltage:
250 VAC, max.
Insulation Resistance:
1000 megohms, min.
Contact Resistance @ 30 amperes:
2 milliohms, max.
Operating Temperature:
–40°C to +95°C
Contact Engagement Force:
40 oz. [11.12 N], max.
*When used with a .180 [4.57]
wide double-sided PC board with
5 oz. [0.14 Kg] min. copper each
side. Consult Tyco Electronics
engineering when paralleling
contacts for power applications.
Wire-to-board housings are
available with and without
mounting ears and with
capabilities of mating with
.062 [1.57], .093 [2.36] and
.125 [3.18] thick double-
sided daughter boards.
These housings are
designed to accept crimp,
snap-in contacts which can
accommodate a wire size
range of 16-10 AWG [1.25-6
m m2]. Contacts are fur-
nished in strip form for auto-
matic machine termination
and in loose form for hand
tool application.
While the basic contact is
designed to carry 30
amperes* of current, the
actual number of contacts in
a connector carrying 30
amperes is limited by the
T” rise of the connector and
the PC board.
174
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Related Product Data:
Performance Specifications
page 173
Connector Housings—page 175
Application Tooling—pages 184, 185
Technical Documents:
(pages 186, 187):
Product Specification
108-9045
Application Specification
114-9005
Instruction Sheets 408-7782,
408-7783, 408-7802
High Current Connectors (Continued)
Material and Finish:
A—Copper alloy CDA-195 plated
.000150 [0.00381] bright tin over
.000030 [0.00076] nickel
B—Copper alloy CDA-195 plated
.000150 [0.00381] silver all over
Crimp, Snap-In Contacts
P l a t i n g Wire Size Ins. Dia. D i m e n s i o n s M a t e a b l e Contact Part Numbers Applicator for Hand Tool
R a n g e Daughter Board A M P - O - L E C T R I C 6 9 7 1 0 - 1
A W G m m2R a n g e ABC T h i c k n e s s Loose Piece Strip Form M a c h i n e Die Insert
. 0 9 0 - . 1 4 5 . 2 6 0 1 . 1 6 0 . 2 8 5 . 0 6 2
A 1 6 - 1 4 1 . 2 5 - 2 2 . 2 9 - 3 . 6 8 6 . 6 0 2 9 . 4 6 7 . 2 4 1 . 5 7 5 3 0 5 1 8 - 1 5 3 0 5 1 7 - 2 4 6 6 4 3 9 - 2 9 0 3 3 3 - 1
. 1 6 0 - . 2 1 0 . 1 9 0 1 . 2 3 0 . 2 8 5 . 0 6 2
A 1 2 - 1 0 3 - 6 4 . 0 6 - 5 . 3 3 4 . 8 3 3 1 . 2 4 7 . 2 4 1 . 5 7 5 3 0 5 2 0 - 1 5 3 0 5 1 9 - 2 4 6 6 4 3 8 - 2 9 0 3 3 2 - 1
. 1 6 0 - . 2 1 0 . 1 9 0 1 . 2 3 0 . 2 8 5 . 0 6 2
B 1 2 - 1 0 3 - 6 4 . 0 6 - 5 . 3 3 4 . 8 3 3 1 . 2 4 7 . 2 4 1 . 5 7 5 3 0 5 1 9 - 3 4 6 6 4 3 8 - 2 9 0 3 3 2 - 1
. 1 6 0 - . 2 1 0 . 1 9 0 1 . 2 3 0 . 3 4 7 . 0 9 3
A 1 2 - 1 0 3 - 6 4 . 0 6 - 5 . 3 3 4 . 8 3 3 1 . 2 4 8 . 8 1 2 . 3 6 5 3 1 3 7 3 - 2 4 6 6 4 3 8 - 2 9 0 3 3 2 - 1
Hand Crimping Tool
69710-1 Extraction Tool
91116-1
A.325
[8.26]
.390
[9.91]
C
.150
[3.81]
.195
[4.95]
B[±.020
[±0.51]
*Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench
machines and lead-making machines.
175
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
High Current Connectors, .312 [7.92] Centerline
Material: White glass-filled polyester,
94V-0 rated
Related Product Data:
Performance Specifications
page 173
Contacts—page 174
Technical Documents:
(pages 186, 187):
Product Specification
108-9045
Instruction Sheet 408-9123
Housings With Mounting Ears
.312
[7.92]
.300
[7.62]
X, Y
PC Board
Thickness
.400
[10.16]
Board Slot
Depth
Void Coring
Optional
.750±.010
[19.05±0.25]
1.400±.010
[35.56±0.25]
.156
[3.96] Dia.
A
C
B
F[±.015*
[±0.38]
D[±.010*
[±0.25]
E[±.007*
[±0.18]
G[±.010*
[±0.25]
Housing Part Numbers
No. Dimensions X = .062 [1.57] Y = .093 [2.36]
of With With
Pos. A B C D E F G Mtg. Ears Mtg. Ears
1.024 .624 1.164 1.114 1.538 1.972 .500
326.01 15.85 29.57 28.3 39.07 50.09 12.70 531370-2
1.336 .936 1.476 1.426 1.850 2.284 .437
433.93 23.77 37.49 36.22 46.99 58.01 11.10 530521-3
2.584 2.184 2.724 2.674 3.098 3.532 .437
865.63 55.47 69.19 67.92 78.69 89.71 11.10 530521-6
2.896 2.496 3.036 2.986 3.410 3.844 .437
973.56 63.40 77.11 75.84 86.61 97.64 11.10 530521-7
3.832 3.432 3.972 3.922 4.346 4.780 .437
12 97.33 87.17 10.89 99.62 110.39 121.41 11.10 530521-9
Notes: 1. XHousings designed to accept .055-.070 [1.4-1.78] thick daughter boards; use intercontact Keying Plug
No. 530533-1.
Notes: 2. YHousings designed to accept .084-.102 [2.13-2.59] thick daughter boards; use intercontact Keying Plug
No. 531369-1. + Contact 531373-2.
N o t e s : 3 . Use Extraction Tool No. 91116-1 to remove contacts. (Refer to Instruction Sheet 408-7782).
4. Other connector sizes can be made available, consult Tyco Electronics.
176
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
High Current Connectors .312 [7.92] Centerline (Continued)
Material and Finish:
Housing—White glass-filled polyester,
94V-0 rated
Contacts
A—Copper alloy CDA-195 plated
.000150 [0.00381] bright tin
over .000030 [0.00076] nickel
B—Copper alloy CDA-195 plated
.000150 [0.00381] silver plate
over .000030 [0.00076] thk. nickel
C—Copper alloy CDA-195 plated
.000030 [0.00076] gold in contact area,
.000150 [0.00381] tin-lead solder post,
over .000030 [0.00076] nickel
Related Product Data:
Performance Specifications
page 173
Technical Documents:
(pages 186, 187):
Product Specification
108-9045
Housings Preloaded with
Solder Tail Contacts
PC Board Thickness: .062 [1.57]
Recommended PC Board Hole Layout
*May go to .020 [0.51] over nominal at top center of housing.
No. of Dimensions Plating Connector
Positions A B C D E F Part Numbers
31.972 1.538 1.164 1.024 .624 .180 A 531353-2
50.09 39.07 29.57 26.01 15.85 4.57
42.284 1.850 1.476 1.336 .936 .180 A 531353-3
58.01 46.99 37.49 33.93 23.77 4.57
52.593 2.162 1.788 1.648 1.248 .180 A 531353-4
65.86 54.91 45.42 41.86 31.70 4.57
62.908 2.474 2.100 1.960 1.560 .180 A 531353-5
73.86 62.84 53.35 49.78 39.62 4.57
.180 A 531353-6
83.532 3.098 2.724 2.584 2.184 4.57 B 145116-3
89.71 78.69 69.19 66.63 55.47 .283 B 146912-2
7.19
93.844 3.410 3.036 2.896 2.496 .180 A 531353-7
97.64 86.61 77.11 73.56 63.40 4.57
.180 A 531353-8
10 4.156 3.722 3.348 3.208 2.808 4.57 B 145116-1
105.56 94.54 85.04 81.48 71.32 .283 B 146912-3
7.19 A 531353-9
.180 B 145116-2
12 4.780 4.346 3.972 3.832 3.432 4.57 C 645200-3
121.41 110.39 100.89 97.33 87.17 .283 B 146912-1
7.19
Notes: 1 . A . 0 6 2 [1.57] thick dummy PC board should be inserted into the connector during soldering to a mother board.
2 . Other connector sizes can be made available, consult Tyco Electronics.
.156
[3.96] Dia.
.130±.003
[3.3±0.08] Dia. .104±.002
[2.64±0.05] Dia.
F
.437±.010*
[11.1±0.25]
.312
[7.92]
.030
[0.76]
Fit for
.062
[1.57]
PC Board
.400
[10.16]
Board Slot
Depth
.300
[7.62]
.937
[23.8]
Void Coring Optional
.218
[5.54]
.539
[13.69]
.375
[9.52]
ED
E
B
.130±.003
[3.3±0.08] Dia. .104±.002
[2.64±0.05] Dia.
.539
[13.69]
.375
[9.52] E
B
B[±.007
[±0.18]
C[±.010
[±0.25]
A[±.015
[±0.38]
177
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
DUO-TYNE Flag Connectors
Product Facts
Right angle design permits
cabling in close quarters
Recessed contacts help
prevent arcing
Sizes and configurations
available with or without
mounting ears
Lowest installed costs
achieved through high-
speed compression crimp-
ing with AMP matched
tooling
Meets quality and reliability
requirements for appliance
controls, vending machine
subassemblies and
business machines
Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
Certified by Canadian
Standards
Association
File No. LR 7189
This flag-type connector is
designed to meet the quali-
ty and reliability of such
equipment as appliance
controls, vending machine
subassemblies, television,
stereo, business machines
and other applications with
similar control needs.
Among its assembly-saving
features is a right-angle
design which permits
cabling in close quarters,
where it does not require
frame mounting to attach
Performance Specifications
Contact Rating*:
5 amperes
High Potential:
2200 VAC, rms
Operating Temperature:
–40°C to +105°C
Vibration:
10 to 55 cps per MIL-STD-1344,
Method 202
the keyed housing to the
card cutout and double
locking of the contacts
when a PC board is
inserted. In addition, con-
tacts are recessed to pre-
vent arcing. All sizes and
configurations are available
with or without mounting
ears. Added to low initial
cost, lowest installed costs
are achieved through high-
speed compression crimp-
ing with Tyco Electronics
matched tooling.
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
178
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
DUO-TYNE Flag Connectors (Continued)
Material and Finish:
Beryllium copper or phosphor bronze
(see chart) plated as follows:
Plating A—.000030 [0.00076] gold in
mating area, with entire contact under-
plated .000050 [0.00127] nickel
Plating B—.000015 [0.00127] gold in
mating area, with entire contact under-
plated .000050 [0.00127] nickel
Plating C—.000150 [0.00381] tin
Related Product Data:
Performance Specifications
page 177
Connector Housings—page 179
Application Tooling—pages 184, 185
Technical Documents:
(pages 186, 187):
Product Specification
108-9038
Application Specification
114-9002
Instruction Sheets 408-7047,
408-7780, 408-7848, 408-7849
T a p e r e d Beam Crimp,
Snap-In Contacts
Hand Crimping Tool Contact Extraction Tool
810992-1
Wire Size Range Contact Contact Part Numbers Applicator for
Insulation Material Finish AMP-O-LECTRIC Hand Tool
AWG mm2Dia. Range (Plating) Loose Piece Strip Form Machine*
26-22 0.12-0 . 4 .035-.055 Beryllium A 530005-3 530004-6
0.89-1.40 Copper B 530004-7 466586-2 90094-4
B 530002-7
Phosphor C 530002-5
Bronze A 530002-3
22-18 0 . 3-0 . 9 .060-.090 C 530006-5 466424-2 90027-4
1.52-2.29 Beryllium A 530006-6
Copper B 530007-3
C 530006-2
.090-.130 Phosphor
18-16 0 . 8-1 . 4 2.29-3.30 Bronze C 530505-5 466413-2
*Applicators are for AMP-O-LECTRIC Model “K” machines. Consult Tyco Electronics for applicators for other bench
machines and lead-making machines.
179
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
DUO-TYNE Flag Connectors (Continued)
Material: Natural nylon
Related Product Data:
Performance Specifications
page 177
Contacts—page 178
PC Board Layout—page 181
Part Number 583661-1
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7486
Housings, With and
Without Mounting Ears
Material: Nylon
On-Contact Keying Plug
Technical Documents:
(pages 186, 187):
Product Specification
108-9038
Application Specification
114-9002
Instruction Sheet 408-7047
Part Numbers
No. Dimensions With Mounting Ears Without Mounting Ears
of For Ins. For Ins. For Ins. For Ins.
Pos. A B C D Dia. Range Dia. Range Dia. Range Dia. Range
. 0 3 5 - . 0 9 0 . 0 9 0 - . 1 3 0 . 0 3 5 - . 0 9 0 . 0 9 0 - . 1 3 0
[ 0 . 8 9 - 2 . 2 9 ] [ 2 . 2 9 - 3 . 3 0 ] [ 0 . 8 9 - 2 . 2 9 ] [ 2 . 2 9 - 3 . 3 0 ]
1.384 .414 .624 1.004
335.15 10.52 15.85 25.50 582380-9
.736 .936
5 22.40 27.74 582370-9 530853-2
1.852 .882 1.092 1.472
647.04 22.40 27.74 37.39 582382-9 530509-1 582371-9 530853-3
2.320 1.350 1.560 1.940
958.93 34.29 39.62 49.28 582383-9 530509-2 582375-9
2.788 1.818 2.028 2.408
12 70.82 46.18 51.51 61.16 582384-9 530509-6 582376-9 530853-5
3.100 2.130 2.340 2.720
14 78.74 54.10 59.44 69.09 582385-9 530509-7 582372-9 530853-6
3.256 2.286 2.496 2.876
15 82.70 58.06 63.40 73.05 582386-9 530509-3 582377-9
3.724 2.754 2.964 3.344
18 94.59 69.95 75.29 84.94 582387-9 530509-8 582378-9 530853-8
4.348 3.378 3.588 3.968
22 110.44 85.80 91.14 100.79 582388-9 530509-9 582379-9
Note: Other connector sizes can be made available, consult Tyco Electronics.
.100
[2.54]
.265
[6.73]
.090
[2.29] .060
[1.52] .095
[2.41]
.375
[9.53]
.500
[12.70]
Fit for
.055-.070
[1.40-1.78]
PCBoard
.156
[3.96]
Dia.
2 Holes
.590
[14.99]
.295
[7.49]
.380
[9.65]
.190
[4.83]
.156
[3.96]
A
B
C
D
180
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
DUO-TYNE Flag Connectors (Continued)
Related PC Board Data:
Recommended Board Thickness
.055-.070 [1.40-1.78]
Recommended Chamfer of Mating
Edge of Boards—.015 [0.38] x 45°
Recommended Pad Plating—Tin
.000150-.000400 [0.00381-0.01016]
thick
Recommended PC
Board Layouts
±.003
A[±0.08]
.044 ±.005
[1.12±0.13]
.156 ±.005
[3.96±0.13]
.070 ±.005
[1.78 ±0.13]
.115
[2.92] Min.
.062 ±.005
[1.57 ±0.13]
.280 ±.008
[ 7 . 1 1±0.13]
Contact Pads
.148 [3.76] R.
Retaining Dimples
(Optional)
Contact Pads
.014/.016
[0.36/0.41]
±.003
A[±0.08]
No. of Dimension
Positions A
3.400
10.16
5.712
18.09
6.868
22.05
91.337
33.96
12 1.805
45.85
14 2.117
53.77
15 2.272
57.71
18 2.741
69.62
22 3.365
85.47
181
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Printed Circuit Board Connector Hood Assemblies
Product Facts
Can be used with the highly
versatile AMP-LEAF and
Crimp Snap Twin Leaf
printed circuit edge
connectors
Clamping capabilities for
wire bundles to .550
[13.97] maximum diameter
Available with 90° or 180°
cable outlet
All plastic construction—
thermoplastic material UL
rated 94V-0 for electrical
and mechanical applica-
tions up to + 105°C
Thermoplastic material has
excellent resistance to
common commercial
cleaners when used at
moderate temperatures
Separate hood assembly
halves permit easy cable
dressing
Furnished in convenient kit
form—each kit includes
four cable clamp sizes
Crimp Snap Twin Leaf Connectors
(Pages 154-163)
AMP-LEAF Connectors
(Pages 164-172)
For use with the following connectors:
182
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Specific Product Name_12 Hel. Con. (Continued)_9pt Helvetica Lt Condensed
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Material: Natural color thermoplastic
Related Product Data:
Crimp Snap Twin Leaf
Connectors—pages 154-163
AMP-LEAF Connectors
pages 164-172
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7719
90° Cable Outlet
.240
[6.10] .260
[6.60] .350
[8.89] .440
[11.18]
.170
[4.32] .625
[15.88]
1.150
[29.21]
1.797
[45.64]
1.500
[38.10]
.375
[9.52]
#5 x 5/8 [15.88]
Thread Forming
Screw (2)
#5 x 3/8 [9.52]
Thread Forming
Screw (3)
Connector Size H o o d Connector Width. 3 80[9 . 65] Max. Connector Width .437[1 1 . 1 0]
L Dim. AMP Hood AMP Hood
No. of Contact Mtg. Hole Length (Max.) Connector Assembly Connector A s s e m b l y
Pos. Centers Centers (Max.) F a m i l y Kit Number* F a m i l y Kit Number*
1.56 3.406 3.685 3.826 AMP-LEAF18 3.96 86.51 93.60 97.18 530088-3
.156 4.031 4.296 4.451 Crimp Snap
22 3.96 102.39 109.12 113.06 Twin Leaf 1-530088-4
*All screws and four sizes of cable clamps are supplied with each kit.
Note: Other hood sizes can be made available, consult Tyco Electronics.
183
Card Edge Connectors
(Board-to-Board, Wire-to-Board)
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Printed Circuit Board Connector Hood Assemblies (Continued)
Material: Natural color thermoplastic
Related Product Data:
AMP-LEAF Connectors
pages 164-172
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7719
18 Cable Outlet
.260
[6.60]
.350
[8.89] .440
[11.18]
.625
[15.88]
.170
[4.32]
.240
[6.10]
1.150
[29.21]
.563
[14.30]
1.500
[38.10]
1.875
[47.62]
#5 x 5/8 [15.88]
Thread Forming
Screw (2)
#5 x 3/8 [9.52]
Thread Forming
Screw (2)
Connector Size Hood Connector Width .380 [9.65] Max.
No. of Contact Mtg. Hole Length L Dim. AMP Connector Hood Assembly
Pos. Centers Centers (Max.) (Max.) F a m i l y Kit Number*
.156 4.031 4.321 4.451
22 3.96 102.39 109.76 113.06 AMP-LEAF 530087-4
*All screws and four sizes of cable clamps are supplied with each kit.
Note: Other hood sizes can be made available, consult Tyco Electronics.
184
Card Edge Connectors
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Application Tooling for Wire Crimp Contacts
Tooling shown on this page is designed to terminate wire
crimp contacts used in various wire-to-board connectors.
This machine also strips
wire, and is therefore used
to terminate jacketed cable.
It features manual precision
adjust, keyed strip blades
for faster, more accurate
setups, and an efficient
scrap removal system.
Applicators are inter-
changeable. All adjust-
ments can be made from
the front of the machine
without special tools.
AMP-O-MATIC Model II Stripper/Crimper Machine
(Shown with Optional Crimp Quality Monitor)
AMP-O-LECTRIC Model “G” Terminating Machine
(Shown with Optional Crimp Quality Monitor)
The AMP-O-LECTRIC Model
“G” is a semi-automatic
bench-top machine for ter-
minating wire using reeled
terminals and contacts. It
features a quiet and reliable
direct motor drive, micro-
processor controls for ease
of setup and operation, and
guarding and lighting
designed for operator con-
venience and safety. Three
versions are available: with
automatic precision adjust
and machine-mounted sen-
sors, or with manual preci-
sion adjust with or without
sensors. All versions will
accept existing T y c o
E l e c t r o n i c s ministyle appli-
cators with minor modifica-
tions.
For further details, request
Tyco Electronics Catalog
65828.
Semiautomatic Bench
Terminator for side- and
end-feed reeled terminals
and contacts. The ELT uses
a DC motor with gear box
drive. The result is a small-
footprint design that is fast
and quiet. Cycle time is less
than 0.400 sec. with an
operation sound level of
76dBa. With a crimp force
capacity of 3,000 pounds,
the ELT is available for all
but the highest crimp force
applications. Optional
equipment is also available
to meet your specific appli-
cation requirements.
For more information,
request catalog 1308382.
Entry Level Terminator (ELT), 1338600-(x)
The combination of the
Stripping Module with the
AMP-O-LECTRIC Model G
Terminator or the Entry
Level Terminator provides
an economical, proficient
method of stripping wire
and crimping terminals on
the same machine. Wires
are stripped moments
before crimping, meaning
there is virtually no chance
of damaging wire conduc-
tors during handling or stor-
age. Once the wire is fed
into the start sensor the
Stripping Module does the
rest, improving placement
accuracy.
For more information,
request catalog 1309085.
Optional Stripping Module for the ELT and AMP-O-LECTRIC
Model G
185
Card Edge Connectors
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Application Tooling for Wire Crimp Contacts (Continued)
Fully-automatic machines
that measure, cut, strip and
terminate single leads.
Microprocessor-controlled,
and programmed and oper-
ated using an easy-to-fol-
low, menu-driven
touchscreen. Features
include direct-drive termi-
nating units with precision
crimp height adjustment,
fully programmable setups,
wire runout and splice
detection, and motorized
pre-feed with wire straight-
ener. Crimp quality monitor-
ing is also available.
For more information,
request catalog 124324.
AMPOMATOR CLS IV+
Lead-Making Machines, 356500-1, -2
Crimp Quality Monitor
(CQM), 1320420-1, -2
This unique system pro-
vides 100% on-the-fly crimp
inspection. It measures the
crimp height of each termi-
nation, and evaluates the
quality of each crimp. If a
crimp is questionable, the
monitor alerts the operator
with both visual and audible
alarms. It also provides
ports for printing and net-
working. When used with
AMP-O-LECTRIC Model “G”
Termination Machines, the
monitor is mounted to the
machine. When used with
AMPOMATOR CLS IV Lead-
Making Machines, it is inte-
grated into the machine’s
operating system.
For more information,
request catalog 82275.
CERTI-CRIMP Straight Action Hand Tools (SAHT)
Premium grade hand tools.
Feature ratchet control to
provide complete crimp
cycle. Die sets close in a
straight line. Include a con-
tact locator and wire stop,
plus an insulation crimp
adjustment lever, when
applicable. Approximate
weight 1.3 lb [0.59 kg].
For more information,
request catalog 65780.
626 Pneumatic Tool System
Lightweight, air-operated
modular tooling system.
Accepts a wide variety of
interchangeable heads for
crimping various types of
contacts, terminals and
splices onto wires ranging
6-26 AWG [13-0.12 mm2],
plus coaxial and fiber optic
cable. Available with either
hand- or foot-actuation
switch. Optional ratchet
control available to provide
complete crimp cycle.
For more information,
request catalog 124208.
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
186
Card Edge Connectors
Technical Documents
The following is a list of technical documents covering
the application, performance and maintenance of the
AMP Card Edge Connectors presented in this catalog.
Product Specifications describe technical performance char-
acteristics and verification tests. They are intended for the
Design, Component and Quality Engineer.
Application Specifications describe requirements for using
the product in its intended application and/or crimping
information. They are intended for the Packaging and
Design Engineer and the Setup person.
Instruction Sheets provide instructions for assembling
or applying the product. They are intended for the
Manufacturing Assembler or Operator.
Solder Type Board-to-Board Connectors
Standard Edge .050 Series PCI Connectors
Product Specification:
108-14034 Standard Edge .050 Series PCI Connector
Application Specification:
114-26012 Standard Edge .050 Series PCI Connector
Standard Edge .050 Series Connectors
Product Specification:
108-14034 Standard Edge .050 Series Connector
Application Specification:
114-26012 Standard Edge .050 Series Connector
Standard Edge II Connectors
Product Specification:
108-9039 Standard Edge II Connector
Low Profile Connectors
Product Specification:
108-9044 Low Profile Edge Connector
Instruction Sheet:
408-7772 Contact Replacement, Low Profile Edge Connector
Twin Leaf Mother Board Connectors
Product Specification:
108-9027 Twin Leaf Mother Board Connector
Instruction Sheets:
408-7479 Keying Plugs, Twin Leaf Mother Board Connector
408-7498 Connector Layout, Twin Leaf Mother Board
Connector
408-7506 Card Guides, Twin Leaf Mother Board Connector
Rotary Cam ZIF Connectors
Product Specification:
108-9048 Rotary Cam PC Board Edge Connector
Instruction Sheet:
408-7911 Rotary Cam ZIF Connectors
Linear ZIF Connectors
Product Specifications:
108-14015 Linear ZIF PC Board Edge Connector,
.100 [2.54] Centerline
108-26003 ACTION PIN Contacts
Application Specification:
114-26003 Linear ZIF PC Board Edge Connector,
.100 [2.54] Centerline
Instruction Sheets:
408-2665 Linear ZIF, Carrier Removal Tool Series
265924
408-2995 Linear ZIF, Housing Wing Removal and
Replacement Tool 266233-1
408-2999 Linear ZIF, T-Bar Insertion Tool Series 266267
408-6915 Linear ZIF, Housing Assembly Insertion Tool
Series 313136
408-6916 Linear ZIF, T-Bar Insertion Tool Series 313139
Press-Fit Board-to-Board Connectors
AMP PACE Connectors
Product Specifications:
108-14019 AMP PACE Connector, .125 x .250 [3.18 x 6.35]
Centerline
108-26003 ACTION PIN Contacts
Application Specification:
114-26002 AMP PACE Connector
Instruction Sheets:
408-2933 Contact Replacement Tool .100 x .200
[2.54 x 5.08] and .125 x .250 [3.18 x 6.35],
AMP PACE Connector
408-2978 Seating Tool Ground Module,
AMP PACE Connector
408-2979 Seating Tool Power Module,
AMP PACE Connector
408-6726 Seating Tool, .156 x .200 [3.96 x 5.08]
Part No. 59955, AMP PACE Connector
408-6727 Seating Tool, .125 x .125 [3.18 x 3.18]
Part No. 59953, AMP PACE Connector
408-6881 Contact Replacement Tool
.100 x .100 [2.54 x 2.54] with and without Scoops
AMP PACE Connector
408-9058 Seating Tool .100 x .200 [2.54 x 5.08] with Card
Scoops, Part No. 58150, AMP PACE Connector
408-9063 Seating Tool .125 x .250 [3.18 x 6.35]
Part No. 58142, AMP PACE Connector
408-9067 Seating Tool .100 x .200 [2.54 x 5.08]
Part No. 58140, AMP PACE Connector
408-9091 Accessories and Tooling, .100 x .200
[2.54 x 5.08] AMP PACE Connector
408-9119 Seating Tool, .125 x .250 [3.18 x 6.35] with Card
Scoops, Part No. 58184, AMP PACE Connector
408-9186 Contact Replacement Tool;
.100 x .200 [2.54 x 5.08],
.125 x .125 [3.18 x 3.18],
.125 x .250 [3.18 x 6.35] with Scoops,
.156 x .200 [3.96 x 5.08],
AMP PACE Connector
408-9188 Seating Tool .100 x .100 [2.54 x 2.54]
Part No. 58200, AMP PACE Connector
ECONOMATE Connectors
Product Specification:
108-26002 ECONOMATE Connector
Instruction Sheet:
408-9091 Accessories and Tooling, .100 x .200 [2.54 x 5.08]
AMP PACE Connector
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
187
Card Edge Connectors
Technical Documents (Continued)
Wire-to-Board Connectors
Crimp Snap Twin Leaf Connectors
Product Specification:
108-9031 Crimp Snap Twin Leaf Connector
(Bifurcated Contacts)
Application Specification:
114-9004 Contact, Twin Leaf Connector
Instruction Sheets:
408-7527 Accessories and Contacts, Crimp Snap Twin
Leaf Connector
408-7529 Extraction Tool 91073-1
408-7531 Hand Tool 90268-1, Single Crimp, 28-24 AWG
[0.08-0.2 mm2] Wire
408-7551 Hand Tool 90264-1, Double Crimp, 22-20 AWG
[0.3-0.6 mm2] and 18 AWG [0.8-0.9 mm2] Wire
408-7583 Hand Tool 90285-1, Double Crimp, 20-18 AWG
[0.5-0.9 mm2] and 16 AWG [1.25-1.4 mm2] Wire
408-8547 CERTI-CRIMP II Straight Action Hand Tools
AMP-LEAF Connectors
Product Specifications:
108-9013 AMP-LEAF Connector
108-9043 AMP-LEAF Connector, Tin Plated Contacts
Application Specification:
114-9003 Contact, AMP-LEAF Connector
Instruction Sheets:
408-6951 Lubricant for tin plating, fretting, corrosion
408-7035 Retaining Spring 42973
408-7036 On-Contact Keying Plugs 480143 and 582756
408-7037 Accessories and Contacts,
AMP-LEAF Connector
408-7045 Extraction Tool 465195
408-7068 Intercontact Keying Plug 582501
408-7339 Intercontact Keying Plug 583274
408-7419 Commoning Springs
408-7622 Hand Tool 90017-3, 22-20 AWG [0.3-0.6 mm2],
Two 22 AWG [0.3-0.4 mm2] or One 18 AWG
[0.8-0.9 mm2] Wire
408-7623 Hand Tool 90028-3, 26-22 AWG [0.12-0.4 mm2],
Two 22 AWG [0.3-0.4 mm2] Wires
408-7624 Hand Tool 90031-8, Two 18 AWG
[0.8-0.9 mm2] Wires
408-7626 Hand Tool 90101-3, 20 AWG [0.5-0.6 mm2] or
Two 20 AWG [0.5-0.6 mm2] Wires
High Current Connectors
Product Specification:
108-9045 High Current Edge Connector
Application Specification:
114-9005 Contact, High Current Edge Connector
Instruction Sheets:
408-7782 Extraction Tool 91116-1, High Current
Connector
408-7783 Die Inserts 90332-1 and 90332-2
408-7802 Die Inserts 90333-1 and 90333-2
408-9123 High Current Connectors
DUO-TYNE Flag Connectors
Product Specification:
108-9038 DUO-TYNE Flag Connector,
Tapered Beam Contact
Application Specification:
114-9002 Contact, DUO-TYNE Flag Connector
Instruction Sheets:
408-7047 DUO-TYNE Flag Right-Angle Connector
408-7486 On-Contact Keying Plug 583661
408-7780 Hand Tool 90335-1, 18-16 AWG
[0.8-1.4 mm2] Wire
408-7848 Hand Tool 90027-4, 22-18 AWG
[0.3-0.9 mm2] Wire
408-7849 Hand Tool 90094-4, 26-22 AWG
[0.12-0.4 mm2] Wire
Printed Circuit Board Connector Hood Assemblies
Instruction Sheet:
408-7719 Printed Circuit Board Connector Hood Assemblies
Card Edge Connectors
188
Part Number Cross Reference—Tyco Part Number to Acquired Part Number
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
11299 9
42973 171
58084 117
58140 115
58142 115
58143 115
58150 115
58184 115
58200 115
58210 115
58218 115
59881 112
60151 165
66067 166
66084 165
66092 171
69710 174
90017 165
90027 174
90028 165
90031 165
90094 174
90101 165
90264 155
90268 155
90285 155
90332 174
90333 174
91081 72
91088 72
91116 174,175
91535 155
98014 57
98341 150
117169 112,122
117249 124,126
117269 124,126
117272 126
117285 121,126
117296 121,126
117311 123
117793 126
117795 120,126
117796 126
117798 120,126
117879 126
117880 126
118243 123
118778 121
118951 120
118982 100,102,
104,105,
106,108,
110,111,
120,121
119136 123
119163 103
119196 88
119200 107
119202 107
119216 103
119216 103
119237 101
119254 110
119256 110
119311 88
119341 112
119413 101
119552 105
119677 103
119726 103
119734 101
119736 101
119738 103
119790 110
119791 103
119802 100,102,
104,106,
108,110,
111,120
119822 107
119831 101
119840 107
119841 107
119853 104
119880 105
119950 93
145031 14
145089 23
145098 9
145113 8
145116 176
145154 9
145165 10
145166 8
145167 9
145168 10
145169 8
145246 10
146912 176
147400 85
147668 129
176137 17
176139 25
265868 126
265871 95,115,
126
265879 126
265881 126
265902 126
265904 126
265905 126
265906 126
265910 126
265911 126
265912 126
265924 95,126
265931 126
265937 126
265962 126
266129 126
266220 115
266233 95,186
266235 95
266264 95
266267 95
313136 95
313139 95
313256 95
343371 165
350396 21
356500 185
465195 165
466366 165
466367 165
466368 165
466413 178
466424 178
466438 174
466439 174
466577 155
466586 178
466622 155
466713 155
466912 155
466919 155
466928 155
480110 165,168,
169
480133 165,168,
169
480142 165,168,
169
480143 171
530002 178
530004 178
530005 178
530006 178
530007 178
530030 72
530061 170
530087 183
530088 182
530213 162
530218 158
530238 160
530245 156
530265 72
530267 72
530268 72
530270 72
530278 72
530282 72
530286 72
530290 72
530291 72
530292 66
530384 22
530396 21
530505 178
530509 179
530517 174
530518 174
530519 174
530520 174
530521 175
530533 175
530654 62
530655 62
530656 62
530657 62
530659 60
530662 60
530663 60
530664 60
530666 62
530667 62
530668 62
530669 62
530671 60
530672 60
530673 60
530674 60
530677 62
530678 62
530689 62
530825 21
530826 22
530841 20
530842 20
530843 17
530844 18
530851 170
530853 179
531004 80
531007 78
531019 74
531020 74
531021 74
531023 77
531024 77
531025 78
531026 78
531250 22,162
All Tyco Electronic Part Numbers without a
corresponding acquired Part Number are listed as
base part numbers only. Complete part numbers
(with prefixes and/or suffixes) are shown on the
page(s) indicated.
Contact Engineering if no corresponding Tyco Number is
a v a i l a b l e .
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
189
Part Number Cross Reference—Tyco Part Number to Acquired Part Number
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
531341 20
531353 176
531369 175
531370 175
531373 174,175
531395 75
531395 75
531396 75
531414 76
531433 62
531476 155
531477 155
531478 155
531534 66
531863 79
532563 79
532600 23
536128 25
582140 165,168
582147 165,168
582264 165,168
582355 166
582370 179
582371 179
582372 179
582375 179
582376 179
582377 179
582378 179
582379 179
582380 179
582382 179
582383 179
582384 179
582385 179
582386 179
582387 179
582388 179
582500 165,168,
169
582501 171
582963 165,168
583167 165,168
583204 165
583274 162,171
583280 165,168
583294 166
583361 165
583407 66,72
583425 71
583454 171
583458 170
583485 66,72
583486 66,72
583533 66,72
583544 170
583545 170
583552 167
583555 165
583599 170
583616 155
583617 165,167
583649 155
583660 68,72
583661 179
583671 70
583679 68,72
583680 165,167
583685 165,167
583691 162
583692 68,72
583694 66
583714 72
583715 68,72
583717 157
583718 157
583722 165,167
583723 165,167
583724 165,167
583725 165,167
583726 165,167
583752 72
583753 72
583754 72
583755 72
583760 171
583764 162
583853 155
583854 156
583857 162
583859 161
583861 157
583864 159
583873 159
583875 155
583879 156
583884 156
583900 158
583975 170
583989 165
583990 165
583991 165
645115 87
645116 91
645135 84
645142 92
645145 85
645146 89
645147 86
645149 90
645155 66
645169 25
645200 176
645235 24
645293 80,82
645384 23
645394 105
650025 17,18,
20,21,
22,23,
24,25,
63
650059 109
650083 79
650090 12
650091 13
650092 12
650118 23
650122 103
650123 103
650124 103
650148 117
650149 117
650150 117
650181 12
650187 23
650207 18
650263 17
650281 117
650297 103
650616 25
650718 20
650719 14
650728 19
678034 107
678035 111
687775 155
810992 178
1320420 185
1338600 184
1437266 151
1490560 150
1490563 150
1571235 109
0-1437261-2 C8D50PF29023 138
0-1437261-5 C8D50PF29033 138
0-1437261-6 C8D50PF29043 140
0-1437262-4 C6D06PF29013 148
0-1437262-5 C6D06PF29043 148
0-1437262-6 C6D10PF29022 146
0-1437262-7 C6D10PF29043 148
0-1437262-9 C6D15PF29022 146
0-1437263-7 C7D06PF29023 142
0-1437263-8 C7D06PF29043 144
0-1437264-3 C1D18PF29015 131
0-1437264-6 C1D20PF29015 131
0-1437264-7 C1D20PF29043 131
0-1437264-9 C1D25PF29013 131
0-1437267-5 A6D06DS29A3 54
0-1437267-6 A6D10DS29A2 54
0-1437267-7 A6D10DS29C2 54
0-1437267-8 A6D10DS29C3 54
0-1437267-9 A6D10RA29A 56
0-1437268-4 A7D06DS29C2 49
0-1437268-5 A7D06RA29C 52
0-1437268-6 A7D06RA29E 52
0-1437268-7 A7D10DS29C2 49
0-1437268-8 A7D10RA29AM231 51
0-1437268-9 A7D10WW29A3 49
0-1437270-1 A8D31DS29B3 43
0-1437270-2 A8D31DS29C2 43
0-1437270-3 A8D31DS29D2 43
0-1437270-4 A8D31RA29A 46
0-1437270-6 A8D31RA29C 46
0-1437270-7 A8D31RA29CM233 47
0-1437270-8 A8D31RA29E 46
0-1437270-9 A8D31RA29F 46
0-1437274-3 C7D06DS29C1 36
0-1437274-5 C7D15DS29C1 36
0-1437274-7 C7D15DS29C3 36
0-1437274-8 C7D18DS29C3 36
0-1437274-9 C7D22DS29C1 36
0-1437276-2 C8D31DS29A3 32
0-1437276-3 C8D31DS29C1 31
0-1437276-5 C8D31DS29C2 31
0-1437276-6 C8D31DS29C3 32
0-1437276-8 C8D31DS29D1 31
0-1437276-9 C8D31DS29D3 32
1-1437260-4 C8D06PF29013 140
1-1437260-5 C8D06PF29043 140
1-1437261-1 C8D60PF29023 138
1-1437262-0 C6D15PF29023 146
1-1437262-3 C6D18PF29013 148
1-1437262-4 C6D18PF29023 146
1-1437262-8 C6D22PF29013 148
1-1437262-9 C6D22PF29023 146
1-1437263-4 C7D18PF29012 144
1-1437263-5 C7D18PF29013 144
1-1437263-6 C7D18PF29022 142
1-1437263-7 C7D18PF29023 142
1-1437263-8 C7D18PF29043 144
1-1437263-9 C7D20PF29012 144
1-1437264-0 C1D25PF29015 131
1-1437264-5 C1D35PF29013 131
1-1437264-6 C1D35PF29015 131
1-1437265-0 W8D18PF29063 136
1-1437265-2 W8D22PF29043 134
1-1437265-3 W8D25PF29013 134
1-1437265-4 W8D25PF29063 136
1-1437265-5 W8D25PF29093 136
1-1437265-6 W8D28PF29013 134
1-1437265-7 W8D28PF29093 136
1-1437266-0 98230 150
1-1437266-1 98231 150
1-1437266-6 98236 150
1-1437266-8 98238 150
1-1437267-0 A6D10RA29AM233 56
1-1437267-1 A6D10RA29C 56
1-1437267-2 A6D10RA29E 56
1-1437267-3 A6D10WW29A3 54
1-1437267-4 A6D12DS29C2 54
Card Edge Connectors
190
Part Number Cross Reference—Tyco Part Number to Acquired Part Number
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
1-1437267-5 A6D12RA29A 54
1-1437267-6 A6D12WW29A3 54
1-1437267-7 A6D15DS29A2 54
1-1437267-9 A6D15DS29C2 54
1-1437268-1 A7D15DS29A2 49
1-1437268-2 A7D15DS29C2 49
1-1437268-3 A7D15RA29C 52
1-1437268-4 A7D15RA29E 52
1-1437268-5 A7D15WW29A3 49
1-1437268-6 A7D18DS29A2 49
1-1437268-7 A7D18DS29B2 49
1-1437268-8 A7D18WW29A3 49
1-1437268-9 A7D22DS29C2 49
1-1437269-9 A8D10DS29A2 43
1-1437270-0 A8D31WW29A3 44
1-1437270-2 A8D35DS29A2 43
1-1437270-3 A8D35DS29C2 43
1-1437270-4 A8D35RA29C 46
1-1437270-5 A8D35WW29A3 44
1-1437270-6 A8D36DS29A2 43
1-1437270-7 A8D36DS29B3 43
1-1437270-8 A8D36DS29C2 43
1-1437270-9 A8D36DS29C3 43
1-1437273-3 C6D06DS29A1 39
1-1437273-4 C6D06DS29C1 39
1-1437273-5 C6D06DS29C3 39
1-1437273-6 C6D06DS29D1 39
1-1437273-7 C6D06DS29D3 39
1-1437273-8 C6D06DS29D4 40
1-1437273-9 C6D10DS29A1 39
1-1437274-0 C7D22DS29D3 36
1-1437274-1 C7D25DS29C1 36
1-1437274-3 C7D28DS29A1 36
1-1437274-4 C7D28DS29A3 36
1-1437274-6 C7D28DS29B3 36
1-1437274-7 C7D28DS29C1 36
1-1437274-8 C7D28DS29C3 36
1-1437274-9 C7D28DS29D1 36
1-1437276-0 C8D35DS29A1 31
1-1437276-1 C8D35DS29A3 32
1-1437276-3 C8D35DS29C3 32
1-1437276-4 C8D35DS29E3 32
1-1437276-5 C8D36DS29A3 32
1-1437276-6 C8D36DS29C1 31
1-1437276-8 C8D36DS29C2 31
1-1437276-9 C8D36DS29C3 32
1437260-4 9820302 151
1437260-5 9820305 151
1437260-6 9836301 151
1437260-7 9836702 151
1437266-3 9818002 151
1437266-4 9818004 151
1437266-5 9818005 151
1437266-6 9820301 151
1437266-7 9820401 151
1437266-8 98206 150
1437266-9 98224 150
1437274-1 98293 150
2-1437260-0 C8D10PF29013 140
2-1437260-2 C8D10PF29023 138
2-1437260-3 C8D10PF29043 140
2-1437260-4 C8D12PF29013 140
2-1437260-5 C8D12PF29023 138
2-1437260-6 C8D12PF29043 140
2-1437260-7 C8D15PF29013 140
2-1437260-9 C8D15PF29023 138
2-1437262-0 C6D22PF29043 148
2-1437262-4 C6D28PF29013 148
2-1437262-6 C6D28PF29023 146
2-1437262-7 C6D28PF29033 146
2-1437262-8 C6D28PF29043 148
2-1437262-9 C6D30PF29023 146
2-1437263-0 C7D20PF29013 144
2-1437263-1 C7D20PF29023 142
2-1437263-3 C7D22PF29013 144
2-1437263-4 C7D22PF29023 142
2-1437263-7 C7D28PF29012 144
2-1437263-8 C7D28PF29013 144
2-1437263-9 C7D28PF29023 142
2-1437264-2 C1D50PF29013 131
2-1437264-3 C1D50PF29015 131
2-1437264-4 C1D50PF29017 132
2-1437265-0 W8D30PF29013 134
2-1437265-1 W8D30PF29043 134
2-1437265-3 W8D35PF29013 134
2-1437265-5 W8D35PF29063 136
2-1437265-6 W8D36PF29013 134
2-1437265-7 W8D36PF29043 134
2-1437265-8 W8D36PF29093 136
2-1437267-0 A6D15RA29E 56
2-1437267-1 A6D15WW29A3 54
2-1437267-2 A6D18DS29A2 54
2-1437267-3 A6D18DS29C2 54
2-1437267-4 A6D18RA29A 56
2-1437267-5 A6D18WW29A3 54
2-1437267-7 A6D22DS29A2 54
2-1437267-8 A6D22DS29B2 54
2-1437267-9 A6D22DS29C2 54
2-1437268-1 A7D25DS29A2 49
2-1437268-2 A7D25RA29FM232 51
2-1437268-3 A7D28DS29A2 49
2-1437268-4 A7D28DS29B2 49
2-1437268-5 A7D28DS29C2 49
2-1437268-8 A7D28RA29AM231 51
2-1437268-9 A7D28RA29C 52
2-1437269-0 A8D10DS29C2 43
2-1437269-1 A8D10RA29A 46
2-1437269-2 A8D10RA29C 46
2-1437269-3 A8D10RA29CM233 47
2-1437269-4 A8D10RA29E 46
2-1437269-5 A8D10WW29A3 44
2-1437269-7 A8D12DS29A2 43
2-1437269-8 A8D12DS29C2 43
2-1437269-9 A8D12RA29C 46
2-1437270-0 A8D36RA29A 46
2-1437270-1 A8D36RA29C 46
2-1437270-2 A8D36RA29E 46
2-1437270-3 A8D36RA29EM233 47
2-1437270-4 A8D36WW29A3 44
2-1437270-6 A8D40DS29A3 43
2-1437270-7 A8D40DS29C2 43
2-1437270-8 A8D40RA29E 46
2-1437270-9 A8D40WW29A3 44
2-1437273-0 C6D10DS29B3 39
2-1437273-1 C6D10DS29C1 39
2-1437273-2 C6D10DS29C4 40
2-1437273-3 C6D12DS29A4 40
2-1437273-4 C6D12DS29C1 39
2-1437273-5 C6D12DS29C3 39
2-1437273-6 C6D15DS29A1 39
2-1437273-7 C6D15DS29B3 39
2-1437273-8 C6D15DS29C1 39
2-1437273-9 C6D15DS29C3 39
2-1437274-0 C7D28DS29D3 36
2-1437274-2 C7D28DS29E3 36
2-1437274-3 C7D28PF29032 142
2-1437274-4 C7D30DS29A3 36
2-1437274-5 C7D30DS29C3 36
2-1437274-6 C7D30DS29C4 37
2-1437274-7 C7D30PF29032 142
2-1437274-8 C7D31DS29A3 36
2-1437274-9 C7D31DS29C3 36
2-1437275-9 C8D06DS29C1 31
2-1437276-0 C8D36DS29D1 31
2-1437276-1 C8D36DS29D2 31
2-1437276-2 C8D36DS29D3 32
2-1437276-3 C8D36DS29E3 32
2-1437276-5 C8D40DS29A1 31
2-1437276-6 C8D40DS29A3 32
2-1437276-7 C8D40DS29C1 31
2-1437276-9 C8D40DS29C3 32
3-1437260-0 C8D15PF29043 140
3-1437260-5 C8D20PF29023 138
3-1437260-6 C8D20PF29043 140
3-1437260-8 C8D22PF29013 140
3-1437262-3 C6D36PF29013 148
3-1437262-4 C6D36PF29023 146
3-1437262-6 C6D43PF29013 148
3-1437262-8 C6D43PF29022 146
3-1437262-9 C6D43PF29023 146
3-1437263-1 C7D30PF29013 144
3-1437263-2 C7D30PF29023 142
3-1437263-3 C7D30PF29043 144
3-1437263-9 C7D35PF29012 144
3-1437264-3 C6D36DS29C3 39
3-1437264-4 C9D020PF60048 129
3-1437264-5 C9D030PF60048 129
3-1437264-6 C9D060PF60048 129
3-1437265-0 W8D40PF29013 134
3-1437265-4 W8D50PF29012 134
3-1437265-5 W8D50PF29013 134
3-1437265-6 W8D50PF29043 134
3-1437265-7 W8D50PF29062 136
3-1437265-9 W8D60PF29013 134
3-1437266-5 98336 150
3-1437266-9 9836701 151
3-1437267-0 A6D22RA29A 56
3-1437267-1 A6D22RA29C 56
3-1437267-2 A6D22WW29A3 54
3-1437267-4 A6D25DS29C2 54
3-1437267-5 A6D28DS29A2 54
3-1437267-6 A6D28DS29C2 54
3-1437267-7 A6D28RA29A 56
3-1437267-8 A6D28RA29C 56
3-1437267-9 A6D28RA29E 56
3-1437268-0 A7D28RA29CM232 51
3-1437268-1 A7D28RA29E 52
3-1437268-2 A7D28RA29EM231 51
3-1437268-3 A7D28WW29A3 49
3-1437268-4 A7D30DS29A2 49
3-1437268-5 A7D30DS29C2 49
3-1437268-6 A7D30RA29AM231 51
3-1437268-7 A7D30WW29A3 49
3-1437268-8 A7D35DS29A2 49
3-1437268-9 A7D35DS29C2 49
3-1437269-0 A8D12RA29E 46
3-1437269-1 A8D12RA29EM233 47
3-1437269-2 A8D12WW29A3 44
3-1437269-8 A8D15DS29A2 43
3-1437269-9 A8D15DS29C2 43
3-1437270-0 A8D43DS29C2 43
3-1437270-1 A8D43RA29A 46
3-1437270-2 A8D43RA29C 46
3-1437270-3 A8D43RA29E 46
3-1437270-4 A8D43WW29A3 44
3-1437270-5 A8D44DS29A2 43
3-1437270-6 A8D44DS29C2 43
3-1437270-7 A8D44DS29C3 44
3-1437270-8 A8D44RA29CM233 47
3-1437270-9 A8D50DS29A2 43
3-1437273-0 C6D15DS29D1 39
3-1437273-1 C6D15DS29D3 39
3-1437273-2 C6D18DS29A1 39
3-1437273-3 C6D18DS29A3 39
3-1437273-4 C6D18DS29C1 39
3-1437273-5 C6D22DS29A1 39
3-1437273-6 C6D22DS29A3 39
3-1437273-7 C6D22DS29B4 40
3-1437273-8 C6D22DS29C1 39
3-1437273-9 C6D22DS29D1 39
3-1437274-0 C7D31DS29D3 36
3-1437274-1 C7D35DS29C1 36
3-1437274-2 C7D36DS29C1 36
3-1437274-3 C7D36DS29C3 36
3-1437274-4 C7D36DS29D3 36
3-1437274-6 C7D40DS29C1 36
3-1437274-7 C7D40DS29C3 36
3-1437274-8 C7D40DS29D3 36
3-1437274-9 C7D43DS29C1 36
3-1437275-0 C8D06DS29C2 31
3-1437275-1 C8D06DS29C3 32
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
191
Part Number Cross Reference—Tyco Part Number to Acquired Part Number
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
3-1437275-2 C8D06DS29E1 31
3-1437275-5 C8D10DS29A3 32
3-1437275-6 C8D10DS29C1 31
3-1437275-8 C8D10DS29C2 31
3-1437275-9 C8D10DS29C3 32
3-1437276-0 C8D40DS29D1 31
3-1437276-1 C8D40DS29D3 32
3-1437276-2 C8D43DS29C1 31
3-1437276-3 C8D43DS29C3 32
3-1437276-4 C8D43DS29D3 32
3-1437276-5 C8D43DS29E1 31
3-1437276-8 C8D50DS29A1 31
3-1437276-9 C8D50DS29A3 32
4-1437260-0 C8D22PF29023 138
4-1437260-1 C8D22PF29043 140
4-1437260-5 C8D25PF29013 140
4-1437260-8 C8D25PF29023 138
4-1437260-9 C8D25PF29033 138
4-1437262-0 C6D43PF29043 148
4-1437263-0 C7D35PF29013 144
4-1437263-1 C7D36PF29012 144
4-1437263-2 C7D36PF29013 144
4-1437263-3 C7D36PF29033 142
4-1437263-4 C7D40PF29012 144
4-1437263-5 C7D40PF29013 144
4-1437263-6 C7D40PF29023 142
4-1437263-7 C7D40PF29032 142
4-1437263-8 C7D40PF29043 144
4-1437267-0 A6D28RA29EM233 56
4-1437267-1 A6D28WW29A3 54
4-1437267-2 A6D36DS29A2 54
4-1437267-3 A6D36DS29A3 54
4-1437267-4 A6D36DS29C2 54
4-1437267-5 A6D36RA29E 56
4-1437267-6 A6D36WW29A3 54
4-1437267-7 A6D43DS29A2 54
4-1437267-8 A6D43DS29A3 54
4-1437267-9 A6D43DS29C2 54
4-1437268-0 A7D35RA29A 52
4-1437268-1 A7D36DS29A2 49
4-1437268-2 A7D36DS29C2 49
4-1437268-3 A7D36RA29AM232 51
4-1437268-4 A7D36WW29A3 49
4-1437268-6 A7D40DS29C2 49
4-1437268-8 A7D40RA29E 52
4-1437268-9 A7D40WW29A3 49
4-1437269-0 A8D15DS29D2 43
4-1437269-1 A8D15RA29C 46
4-1437269-2 A8D15RA29CM233 47
4-1437269-3 A8D15RA29E 46
4-1437269-4 A8D15RA29EM233 47
4-1437269-5 A8D15RA29FM233 47
4-1437269-6 A8D15WW29A3 44
4-1437269-8 A8D18DS29A2 43
4-1437269-9 A8D18DS29C2 43
4-1437270-0 A8D50DS29C2 43
4-1437270-1 A8D50DS29C3 44
4-1437270-2 A8D50DS29D2 43
4-1437270-4 A8D50RA29C 46
4-1437270-5 A8D50RA29E 46
4-1437270-6 A8D50RA29F 46
4-1437270-7 A8D50WW29A3 44
4-1437273-0 C6D22DS29D3 39
4-1437273-1 C6D25DS29A3 39
4-1437273-2 C6D25DS29C3 39
4-1437273-3 C6D25DS29D1 39
4-1437273-4 C6D28DS29C1 39
4-1437273-6 C6D28DS29C3 39
4-1437273-7 C6D28DS29D1 39
4-1437273-8 C6D30DS29C1 39
4-1437273-9 C6D30DS29C3 39
4-1437274-0 C7D43DS29C3 36
4-1437274-1 C7D43DS29D4 37
4-1437274-3 C7D50DS29A3 36
4-1437274-4 C7D50DS29C1 36
4-1437274-5 C7D50DS29C3 36
4-1437274-6 C7D50DS29C4 37
4-1437274-8 C7D50DS29D3 36
4-1437275-0 C8D10DS29D1 31
4-1437275-1 C8D10DS29D3 32
4-1437275-5 C8D12DS29C1 31
4-1437275-7 C8D12DS29C3 32
4-1437275-8 C8D12DS29D1 31
4-1437276-0 C8D50DS29C1 31
4-1437276-2 C8D50DS29C3 32
4-1437276-3 C8D50DS29D1 31
4-1437276-6 C8D52DS29C1M191 29
4-1437276-7 C8D52DS29C1M195 29
5-1437260-5 C8D28PF29023 138
5-1437260-6 C8D30PF29013 140
5-1437260-8 C8D30PF29023 138
5-1437263-0 C7D43PF29013 144
5-1437263-1 C7D50DS29B3 36
5-1437263-2 C7D50PF29013 144
5-1437263-3 C7D50PF29033 142
5-1437263-4 C7D50PF29043 144
5-1437263-7 C7D50PF29143 142
5-1437267-0 A6D43DS29C3 54
5-1437267-1 A6D43RA29AM233 56
5-1437267-2 A6D43RA29C 56
5-1437267-3 A6D43RA29E 56
5-1437267-4 A6D43WW29A3 54
5-1437268-0 A7D40WW29B3 49
5-1437268-2 A7D43DS29A2 49
5-1437268-3 A7D43DS29C2 49
5-1437268-4 A7D43WW29A3 49
5-1437268-5 A7D50DS29A2 49
5-1437268-6 A7D50DS29C2 49
5-1437268-8 A7D50DS29D2 49
5-1437269-0 A8D18DS29C3 43
5-1437269-1 A8D18RA29C 46
5-1437269-2 A8D18RA29CM233 47
5-1437269-3 A8D18RA29FM233 47
5-1437269-4 A8D18WW29A3 44
5-1437269-6 A8D20DS29B2 43
5-1437269-7 A8D20DS29C2 43
5-1437269-8 A8D20RA29C 46
5-1437269-9 A8D20RA29E 46
5-1437270-1 A8D60DS29A2 43
5-1437270-2 A8D60DS29C2 43
5-1437270-3 A8D60DS29C3 44
5-1437270-5 A8D60RA29A 46
5-1437270-6 A8D60WW29A3 44
5-1437270-9 A8D65DS29C2 43
5-1437273-0 C6D30DS29D3 39
5-1437273-1 C6D30DS29D4 40
5-1437273-2 C6D31DS29A1 39
5-1437273-3 C6D36DS29A3 39
5-1437273-4 C6D36DS29C1 39
5-1437273-5 C6D36DS29D1 39
5-1437273-6 C6D36DS29D4 40
5-1437273-7 C6D36DS29E4 40
5-1437273-8 C6D40DS29B3 39
5-1437273-9 C6D43DS29A1 39
5-1437274-0 C7D50DS29E1 36
5-1437274-1 C8D12DS29E1 31
5-1437275-1 C8D15DS29B3 32
5-1437275-2 C8D15DS29C1 31
5-1437275-4 C8D15DS29C3 32
5-1437275-5 C8D15DS29D1 31
5-1437275-6 C8D15DS29D2 31
5-1437275-9 C8D18DS29C1 31
5-1437276-1 C8D60DS29A1 31
5-1437276-2 C8D60DS29A3 32
5-1437276-3 C8D60DS29B3 32
5-1437276-4 C8D60DS29C1 31
5-1437276-7 C8D60DS29D1 31
5-1437276-8 C8D60PF29013 140
6-1437260-1 C8D30PF29043 140
6-1437260-4 C8D30PF29133 140
6-1437260-5 C8D31PF29013 140
6-1437260-6 C8D31PF29023 138
6-1437260-7 C8D31PF29043 140
6-1437260-8 C8D31PF29132 140
6-1437260-9 C8D31PF29133 140
6-1437268-0 A7D50RA29A 52
6-1437268-1 A7D50WW29A3 49
6-1437268-2 A7D50WW29B3 49
6-1437269-0 A8D20WW29A3 44
6-1437269-1 A8D22DS29A2 43
6-1437269-2 A8D22DS29C2 43
6-1437269-4 A8D22RA29A 46
6-1437269-5 A8D22RA29C 46
6-1437269-6 A8D22RA29E 46
6-1437269-7 A8D22RA29EM233 47
6-1437269-8 A8D22WW29A3 44
6-1437269-9 A8D25DS29A2 43
6-1437270-0 A8D65DS29D2 43
6-1437270-6 A8D28RA29C 46
6-1437273-0 C6D43DS29A4 40
6-1437273-1 C6D43DS29B1 39
6-1437273-2 C6D43DS29C1 39
6-1437273-4 C6D43DS29C3 39
6-1437273-6 C6D43DS29D3 39
6-1437275-1 C8D18DS29C3 32
6-1437275-2 C8D18DS29D1 31
6-1437275-3 C8D18DS29D3 32
6-1437275-4 C8D18DS29E1 31
6-1437275-6 C8D20DS29C1 31
6-1437275-8 C8D20DS29C3 32
6-1437275-9 C8D20DS29D1 31
7-1437260-3 C8D35PF29023 138
7-1437260-7 C8D36PF29013 140
7-1437260-9 C8D36PF29022 138
7-1437269-0 A8D25DS29B2 43
7-1437269-1 A8D25DS29C2 43
7-1437269-2 A8D25DS29C3 43
7-1437269-3 A8D25RA29A 46
7-1437269-4 A8D25RA29AM233 47
7-1437269-5 A8D25RA29C 46
7-1437269-6 A8D25RA29CM233 47
7-1437269-7 A8D25RA29E 46
7-1437269-8 A8D25RA29FM233 47
7-1437269-9 A8D25WW29A3 44
7-1437275-0 C8D20DS29D3 32
7-1437275-1 C8D22DS29A1 31
7-1437275-2 C8D22DS29A3 32
7-1437275-3 C8D22DS29B1 31
7-1437275-4 C8D22DS29C1 31
7-1437275-6 C8D22DS29C3 32
7-1437275-7 C8D22DS29D1 31
7-1437275-8 C8D25DS29A1 31
7-1437275-9 C8D25DS29A3 32
8-1437260-0 C8D36PF29023 138
8-1437260-1 C8D36PF29033 138
8-1437260-2 C8D36PF29043 140
8-1437260-4 C8D40PF29023 138
8-1437260-6 C8D40PF29043 140
8-1437260-9 C8D43PF29012 140
8-1437269-1 A8D28DS29A2 43
8-1437269-2 A8D28DS29C2 43
8-1437269-3 A8D28RA29E 46
8-1437269-5 A8D30DS29A2 43
8-1437269-6 A8D30DS29B2 43
8-1437269-7 A8D30DS29C2 43
8-1437269-9 A8D30DS29C3 43
8-1437275-0 C8D25DS29C1 31
8-1437275-2 C8D25DS29C3 32
8-1437275-3 C8D25DS29D1 31
8-1437275-4 C8D25DS29D3 32
8-1437275-5 C8D28DS29C1 31
8-1437275-8 C8D28DS29C3 32
8-1437275-9 C8D28DS29D1 31
9-1437260-0 C8D43PF29013 140
9-1437260-2 C8D43PF29022 138
9-1437260-3 C8D43PF29023 138
9-1437260-9 C8D50PF29013 140
9-1437269-0 A8D30DS29D2 43
9-1437269-1 A8D30DS29D2 43
9-1437269-2 A8D30RA29C 46
9-1437269-3 A8D30RA29E 46
Card Edge Connectors
192
9-1437269-4 A8D30WW29A3 44
9-1437269-5 A8D30WW29B3 44
9-1437269-8 A8D31DS29A2 43
9-1437269-9 A8D31DS29A3 43
9-1437275-0 C8D28DS29D3 32
9-1437275-1 C8D28PF29012 140
9-1437275-3 C8D30DS29C1 31
9-1437275-5 C8D30DS29C3 32
9-1437275-6 C8D30DS29D1 31
9-1437275-7 C8D30DS29D3 32
9-1437275-8 C8D30DS29E1 31
9-1437275-9 C8D30DS29E3 32
AP3 149
BMEP 1K/2K 149
BMEP 3T/5T 149
MEP 6T/12T 149
Model G 184
SAHT 185
Part Number Cross Reference—Tyco Part Number to Acquired Part Number
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Tyco A c q u i r e d P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
193
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
9 8 2 0 6 1 4 3 7 2 6 6 - 8 1 5 0
9 8 2 2 4 1 4 3 7 2 6 6 - 9 1 5 0
9 8 2 3 0 1 - 1 4 3 7 2 6 6 - 0 1 5 0
9 8 2 3 1 1 - 1 4 3 7 2 6 6 - 1 1 5 0
9 8 2 3 6 1 - 1 4 3 7 2 6 6 - 6 1 5 0
9 8 2 3 8 1 - 1 4 3 7 2 6 6 - 8 1 5 0
9 8 2 9 3 1 4 3 7 2 7 4 - 1 1 5 0
9 8 3 3 6 3 - 1 4 3 7 2 6 6 - 5 1 5 0
9 8 1 8 0 0 1 1 5 1
9 8 1 8 0 0 2 1 4 3 7 2 6 6 - 3 1 5 1
9 8 1 8 0 0 3 1 5 1
9 8 1 8 0 0 4 1 4 3 7 2 6 6 - 4 1 5 1
9 8 1 8 0 0 5 1 4 3 7 2 6 6 - 5 1 5 1
9 8 2 0 3 0 1 1 4 3 7 2 6 6 - 6 1 5 1
9 8 2 0 3 0 2 1 4 3 7 2 6 0 - 4 1 5 1
9 8 2 0 3 0 3 1 5 1
9 8 2 0 3 0 5 1 4 3 7 2 6 0 - 5 1 5 1
9 8 2 0 4 0 1 1 4 3 7 2 6 6 - 7 1 5 1
9 8 3 6 3 0 1 1 4 3 7 2 6 0 - 6 1 5 1
9 8 3 6 7 0 1 3 - 1 4 3 7 2 6 6 - 9 1 5 1
9 8 3 6 7 0 2 1 4 3 7 2 6 0 - 7 1 5 1
A 6 D 0 6 D S 2 9 A 2 5 4
A 6 D 0 6 D S 2 9 A 3 0 - 1 4 3 7 2 6 7 - 5 5 4
A 6 D 0 6 D S 2 9 B 2 5 4
A 6 D 0 6 D S 2 9 B 3 5 4
A 6 D 0 6 D S 2 9 C 2 5 4
A 6 D 0 6 D S 2 9 C 3 5 4
A 6 D 0 6 R A 2 9 A 5 6
A 6 D 0 6 R A 2 9 A M 2 3 3 5 6
A 6 D 0 6 R A 2 9 C 5 6
A 6 D 0 6 R A 2 9 C M 2 3 3 5 6
A 6 D 0 6 R A 2 9 E 5 6
A 6 D 0 6 R A 2 9 E M 2 3 3 5 6
A 6 D 0 6 R A 2 9 F 5 6
A 6 D 0 6 R A 2 9 F M 2 3 3 5 6
A 6 D 0 6 W W 2 9 A 3 5 4
A 6 D 0 6 W W 2 9 B 3 5 4
A 6 D 1 0 D S 2 9 A 2 0 - 1 4 3 7 2 6 7 - 6 5 4
A 6 D 1 0 D S 2 9 A 3 5 4
A 6 D 1 0 D S 2 9 B 2 5 4
A 6 D 1 0 D S 2 9 B 3 5 4
A 6 D 1 0 D S 2 9 C 2 0 - 1 4 3 7 2 6 7 - 7 5 4
A 6 D 1 0 D S 2 9 C 3 0 - 1 4 3 7 2 6 7 - 8 5 4
A 6 D 1 0 R A 2 9 A 0 - 1 4 3 7 2 6 7 - 9 5 6
A 6 D 1 0 R A 2 9 A M 2 3 3 1 - 1 4 3 7 2 6 7 - 0 5 6
A 6 D 1 0 R A 2 9 C 1 - 1 4 3 7 2 6 7 - 1 5 6
A 6 D 1 0 R A 2 9 C M 2 3 3 5 6
A 6 D 1 0 R A 2 9 E 1 - 1 4 3 7 2 6 7 - 2 5 6
A 6 D 1 0 R A 2 9 E M 2 3 3 5 6
A 6 D 1 0 R A 2 9 F 5 6
A 6 D 1 0 R A 2 9 F M 2 3 3 5 6
A 6 D 1 0 W W 2 9 A 3 1 - 1 4 3 7 2 6 7 - 3 5 4
A 6 D 1 0 W W 2 9 B 3 5 4
A 6 D 1 2 D S 2 9 A 2 5 4
A 6 D 1 2 D S 2 9 A 3 5 4
A 6 D 1 2 D S 2 9 B 2 5 4
A 6 D 1 2 D S 2 9 B 3 5 4
A 6 D 1 2 D S 2 9 C 2 1 - 1 4 3 7 2 6 7 - 4 5 4
A 6 D 1 2 D S 2 9 C 3 5 4
A 6 D 1 2 R A 2 9 A 1 - 1 4 3 7 2 6 7 - 5 5 4
A 6 D 1 2 R A 2 9 A M 2 3 3 5 6
A 6 D 1 2 R A 2 9 C 5 6
A 6 D 1 2 R A 2 9 C M 2 3 3 5 6
A 6 D 1 2 R A 2 9 E 5 6
A 6 D 1 2 R A 2 9 E M 2 3 3 5 6
A 6 D 1 2 R A 2 9 F 5 6
A 6 D 1 2 R A 2 9 F M 2 3 3 5 6
A 6 D 1 2 W W 2 9 A 3 1 - 1 4 3 7 2 6 7 - 6 5 4
A 6 D 1 2 W W 2 9 B 3 5 4
A 6 D 1 5 D S 2 9 A 2 1 - 1 4 3 7 2 6 7 - 7 5 4
A 6 D 1 5 D S 2 9 A 3 5 4
A 6 D 1 5 D S 2 9 B 2 5 4
A 6 D 1 5 D S 2 9 B 3 5 4
A 6 D 1 5 D S 2 9 C 2 1 - 1 4 3 7 2 6 7 - 9 5 4
A 6 D 1 5 D S 2 9 C 3 5 4
A 6 D 1 5 R A 2 9 A 5 6
A 6 D 1 5 R A 2 9 A M 2 3 3 5 6
A 6 D 1 5 R A 2 9 C 5 6
A 6 D 1 5 R A 2 9 C M 2 3 3 5 6
A 6 D 1 5 R A 2 9 E 2 - 1 4 3 7 2 6 7 - 0 5 6
A 6 D 1 5 R A 2 9 E M 2 3 3 5 6
A 6 D 1 5 R A 2 9 F 5 6
A 6 D 1 5 R A 2 9 F M 2 3 3 5 6
A 6 D 1 5 W W 2 9 A 3 2 - 1 4 3 7 2 6 7 - 1 5 4
A 6 D 1 5 W W 2 9 B 3 5 4
A 6 D 1 8 D S 2 9 A 2 2 - 1 4 3 7 2 6 7 - 2 5 4
A 6 D 1 8 D S 2 9 A 3 5 4
A 6 D 1 8 D S 2 9 B 2 5 4
A 6 D 1 8 D S 2 9 B 3 5 4
A 6 D 1 8 D S 2 9 C 2 2 - 1 4 3 7 2 6 7 - 3 5 4
A 6 D 1 8 D S 2 9 C 3 5 4
A 6 D 1 8 R A 2 9 A 2 - 1 4 3 7 2 6 7 - 4 5 6
A 6 D 1 8 R A 2 9 A M 2 3 3 5 6
A 6 D 1 8 R A 2 9 C 5 6
A 6 D 1 8 R A 2 9 C M 2 3 3 5 6
A 6 D 1 8 R A 2 9 E 5 6
A 6 D 1 8 R A 2 9 E M 2 3 3 5 6
A 6 D 1 8 R A 2 9 F 5 6
A 6 D 1 8 R A 2 9 F M 2 3 3 5 6
A 6 D 1 8 W W 2 9 A 3 2 - 1 4 3 7 2 6 7 - 5 5 4
A 6 D 1 8 W W 2 9 B 3 5 4
A 6 D 2 2 D S 2 9 A 2 2 - 1 4 3 7 2 6 7 - 7 5 4
A 6 D 2 2 D S 2 9 A 3 5 4
A 6 D 2 2 D S 2 9 B 2 2 - 1 4 3 7 2 6 7 - 8 5 4
A 6 D 2 2 D S 2 9 B 3 5 4
A 6 D 2 2 D S 2 9 C 2 2 - 1 4 3 7 2 6 7 - 9 5 4
A 6 D 2 2 D S 2 9 C 3 5 4
A 6 D 2 2 R A 2 9 A 3 - 1 4 3 7 2 6 7 - 0 5 6
A 6 D 2 2 R A 2 9 A M 2 3 3 5 6
A 6 D 2 2 R A 2 9 C 3 - 1 4 3 7 2 6 7 - 1 5 6
A 6 D 2 2 R A 2 9 C M 2 3 3 5 6
A 6 D 2 2 R A 2 9 E 5 6
A 6 D 2 2 R A 2 9 E M 2 3 3 5 6
A 6 D 2 2 R A 2 9 F 5 6
A 6 D 2 2 R A 2 9 F M 2 3 3 5 6
A 6 D 2 2 W W 2 9 A 3 3 - 1 4 3 7 2 6 7 - 2 5 4
A 6 D 2 2 W W 2 9 B 3 5 4
A 6 D 2 5 D S 2 9 A 2 5 4
A 6 D 2 5 D S 2 9 A 3 5 4
A 6 D 2 5 D S 2 9 B 2 5 4
A 6 D 2 5 D S 2 9 B 3 5 4
A 6 D 2 5 D S 2 9 C 2 3 - 1 4 3 7 2 6 7 - 4 5 4
A 6 D 2 5 D S 2 9 C 3 5 4
A 6 D 2 5 R A 2 9 A 5 6
A 6 D 2 5 R A 2 9 A M 2 3 3 5 6
A 6 D 2 5 R A 2 9 C 5 6
A 6 D 2 5 R A 2 9 C M 2 3 3 5 6
A 6 D 2 5 R A 2 9 E 5 6
A 6 D 2 5 R A 2 9 E M 2 3 3 5 6
A 6 D 2 5 R A 2 9 F 5 6
A 6 D 2 5 R A 2 9 F M 2 3 3 5 6
A 6 D 2 5 W W 2 9 A 3 5 4
A 6 D 2 5 W W 2 9 B 3 5 4
A 6 D 2 8 D S 2 9 A 2 3 - 1 4 3 7 2 6 7 - 5 5 4
A 6 D 2 8 D S 2 9 A 3 5 4
A 6 D 2 8 D S 2 9 B 2 5 4
A 6 D 2 8 D S 2 9 B 3 5 4
A 6 D 2 8 D S 2 9 C 2 3 - 1 4 3 7 2 6 7 - 6 5 4
A 6 D 2 8 D S 2 9 C 3 5 4
A 6 D 2 8 R A 2 9 A 3 - 1 4 3 7 2 6 7 - 7 5 6
A 6 D 2 8 R A 2 9 A M 2 3 3 5 6
A 6 D 2 8 R A 2 9 C 3 - 1 4 3 7 2 6 7 - 8 5 6
A 6 D 2 8 R A 2 9 C M 2 3 3 5 6
A 6 D 2 8 R A 2 9 E 3 - 1 4 3 7 2 6 7 - 9 5 6
A 6 D 2 8 R A 2 9 E M 2 3 3 4 - 1 4 3 7 2 6 7 - 0 5 6
A 6 D 2 8 R A 2 9 F 5 6
A 6 D 2 8 R A 2 9 F M 2 3 3 5 6
A 6 D 2 8 W W 2 9 A 3 4 - 1 4 3 7 2 6 7 - 1 5 4
A 6 D 2 8 W W 2 9 B 3 5 4
A 6 D 3 6 D S 2 9 A 2 4 - 1 4 3 7 2 6 7 - 2 5 4
A 6 D 3 6 D S 2 9 A 3 4 - 1 4 3 7 2 6 7 - 3 5 4
A 6 D 3 6 D S 2 9 B 2 5 4
A 6 D 3 6 D S 2 9 B 3 5 4
A 6 D 3 6 D S 2 9 C 2 4 - 1 4 3 7 2 6 7 - 4 5 4
A 6 D 3 6 D S 2 9 C 3 5 4
A 6 D 3 6 R A 2 9 A 5 6
A 6 D 3 6 R A 2 9 A M 2 3 3 5 6
A 6 D 3 6 R A 2 9 C 5 6
A 6 D 3 6 R A 2 9 C M 2 3 3 5 6
A 6 D 3 6 R A 2 9 E 4 - 1 4 3 7 2 6 7 - 5 5 6
A 6 D 3 6 R A 2 9 E M 2 3 3 5 6
A 6 D 3 6 R A 2 9 F 5 6
A 6 D 3 6 R A 2 9 F M 2 3 3 5 6
A 6 D 3 6 W W 2 9 A 3 4 - 1 4 3 7 2 6 7 - 6 5 4
A 6 D 3 6 W W 2 9 B 3 5 4
A 6 D 4 0 R A 2 9 A 5 6
A 6 D 4 0 R A 2 9 A M 2 3 3 5 6
A 6 D 4 0 R A 2 9 C 5 6
A 6 D 4 0 R A 2 9 C M 2 3 3 5 6
A 6 D 4 0 R A 2 9 E 5 6
A 6 D 4 0 R A 2 9 E M 2 3 3 5 6
A 6 D 4 0 R A 2 9 F 5 6
A 6 D 4 0 R A 2 9 F M 2 3 3 5 6
A 6 D 4 3 D S 2 9 A 2 4 - 1 4 3 7 2 6 7 - 7 5 4
A 6 D 4 3 D S 2 9 A 3 4 - 1 4 3 7 2 6 7 - 8 5 4
A 6 D 4 3 D S 2 9 B 2 5 4
A 6 D 4 3 D S 2 9 B 3 5 4
A 6 D 4 3 D S 2 9 C 2 4 - 1 4 3 7 2 6 7 - 9 5 4
A 6 D 4 3 D S 2 9 C 3 5 - 1 4 3 7 2 6 7 - 0 5 4
A 6 D 4 3 R A 2 9 A 5 6
A 6 D 4 3 R A 2 9 A M 2 3 3 5 - 1 4 3 7 2 6 7 - 1 5 6
A 6 D 4 3 R A 2 9 C 5 - 1 4 3 7 2 6 7 - 2 5 6
A 6 D 4 3 R A 2 9 C M 2 3 3 5 6
A 6 D 4 3 R A 2 9 E 5 - 1 4 3 7 2 6 7 - 3 5 6
A 6 D 4 3 R A 2 9 E M 2 3 3 5 6
A 6 D 4 3 R A 2 9 F 5 6
A 6 D 4 3 R A 2 9 F M 2 3 3 5 6
A 6 D 4 3 W W 2 9 A 3 5 - 1 4 3 7 2 6 7 - 4 5 4
A 6 D 4 3 W W 2 9 B 3 5 4
A 7 D 0 6 D S 2 9 A 2 4 9
A 7 D 0 6 D S 2 9 B 2 4 9
A 7 D 0 6 D S 2 9 C 2 0 - 1 4 3 7 2 6 8 - 4 4 9
A 7 D 0 6 D S 2 9 D 2 4 9
A 7 D 0 6 D S 2 9 E 2 4 9
A 7 D 0 6 R A 2 9 A 5 2
A 7 D 0 6 R A 2 9 A M 2 3 1 5 1
A 7 D 0 6 R A 2 9 A M 2 3 2 5 1
A 7 D 0 6 R A 2 9 C 0 - 1 4 3 7 2 6 8 - 5 5 2
A 7 D 0 6 R A 2 9 C M 2 3 1 5 1
A 7 D 0 6 R A 2 9 C M 2 3 2 5 1
A 7 D 0 6 R A 2 9 E 0 - 1 4 3 7 2 6 8 - 6 5 2
A 7 D 0 6 R A 2 9 E M 2 3 1 5 1
A 7 D 0 6 R A 2 9 E M 2 3 2 5 1
A 7 D 0 6 R A 2 9 F 5 2
A 7 D 0 6 R A 2 9 F M 2 3 1 5 1
A 7 D 0 6 R A 2 9 F M 2 3 2 5 1
A 7 D 0 6 W W 2 9 A 3 4 9
A 7 D 0 6 W W 2 9 B 3 4 9
A 7 D 1 0 D S 2 9 A 2 4 9
A 7 D 1 0 D S 2 9 B 2 4 9
A 7 D 1 0 D S 2 9 C 2 0 - 1 4 3 7 2 6 8 - 7 4 9
A 7 D 1 0 D S 2 9 D 2 4 9
A 7 D 1 0 D S 2 9 E 2 4 9
A 7 D 1 0 R A 2 9 A 5 2
A 7 D 1 0 R A 2 9 A M 2 3 1 0 - 1 4 3 7 2 6 8 - 8 5 1
A 7 D 1 0 R A 2 9 A M 2 3 2 5 1
A 7 D 1 0 R A 2 9 C 5 2
A 7 D 1 0 R A 2 9 C M 2 3 1 5 1
A 7 D 1 0 R A 2 9 C M 2 3 2 5 1
A 7 D 1 0 R A 2 9 E 5 2
A 7 D 1 0 R A 2 9 E M 2 3 1 5 1
A 7 D 1 0 R A 2 9 E M 2 3 2 5 1
A 7 D 1 0 R A 2 9 F 5 2
A 7 D 1 0 R A 2 9 F M 2 3 1 5 1
A 7 D 1 0 R A 2 9 F M 2 3 2 5 1
A 7 D 1 0 W W 2 9 A 3 0 - 1 4 3 7 2 6 8 - 9 4 9
A 7 D 1 0 W W 2 9 B 3 4 9
A 7 D 1 5 D S 2 9 A 2 1 - 1 4 3 7 2 6 8 - 1 4 9
A 7 D 1 5 D S 2 9 B 2 4 9
A 7 D 1 5 D S 2 9 C 2 1 - 1 4 3 7 2 6 8 - 2 4 9
A 7 D 1 5 D S 2 9 D 2 4 9
A 7 D 1 5 D S 2 9 E 2 4 9
A 7 D 1 5 R A 2 9 A 5 2
A 7 D 1 5 R A 2 9 A M 2 3 1 5 1
A 7 D 1 5 R A 2 9 A M 2 3 2 5 1
A 7 D 1 5 R A 2 9 C 1 - 1 4 3 7 2 6 8 - 3 5 2
A 7 D 1 5 R A 2 9 C M 2 3 1 5 1
A 7 D 1 5 R A 2 9 C M 2 3 2 5 1
A 7 D 1 5 R A 2 9 E 1 - 1 4 3 7 2 6 8 - 4 5 2
A 7 D 1 5 R A 2 9 E M 2 3 1 5 1
A 7 D 1 5 R A 2 9 E M 2 3 2 5 1
A 7 D 1 5 R A 2 9 F 5 2
A 7 D 1 5 R A 2 9 F M 2 3 1 5 1
A 7 D 1 5 R A 2 9 F M 2 3 2 5 1
A 7 D 1 5 W W 2 9 A 3 1 - 1 4 3 7 2 6 8 - 5 4 9
A 7 D 1 5 W W 2 9 B 3 4 9
A 7 D 1 8 D S 2 9 A 2 1 - 1 4 3 7 2 6 8 - 6 4 9
A 7 D 1 8 D S 2 9 B 2 1 - 1 4 3 7 2 6 8 - 7 4 9
A 7 D 1 8 D S 2 9 C 2 4 9
A 7 D 1 8 D S 2 9 D 2 4 9
A 7 D 1 8 D S 2 9 E 2 4 9
A 7 D 1 8 R A 2 9 A 5 2
A 7 D 1 8 R A 2 9 A M 2 3 1 5 1
A 7 D 1 8 R A 2 9 A M 2 3 2 5 1
A 7 D 1 8 R A 2 9 C 5 2
A 7 D 1 8 R A 2 9 C M 2 3 1 5 1
A 7 D 1 8 R A 2 9 C M 2 3 2 5 1
A 7 D 1 8 R A 2 9 E 5 2
A 7 D 1 8 R A 2 9 E M 2 3 1 5 1
A 7 D 1 8 R A 2 9 E M 2 3 2 5 1
A 7 D 1 8 R A 2 9 F 5 2
A 7 D 1 8 R A 2 9 F M 2 3 1 5 1
A 7 D 1 8 R A 2 9 F M 2 3 2 5 1
A 7 D 1 8 W W 2 9 A 3 1 - 1 4 3 7 2 6 8 - 8 4 9
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
194
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
A 7 D 1 8 W W 2 9 B 3 4 9
A 7 D 2 2 D S 2 9 A 2 4 9
A 7 D 2 2 D S 2 9 B 2 4 9
A 7 D 2 2 D S 2 9 C 2 1 - 1 4 3 7 2 6 8 - 9 4 9
A 7 D 2 2 R A 2 9 A 5 2
A 7 D 2 2 R A 2 9 A M 2 3 1 5 1
A 7 D 2 2 R A 2 9 A M 2 3 2 5 1
A 7 D 2 2 R A 2 9 C 5 2
A 7 D 2 2 R A 2 9 C M 2 3 1 5 1
A 7 D 2 2 R A 2 9 C M 2 3 2 5 1
A 7 D 2 2 R A 2 9 E 5 2
A 7 D 2 2 R A 2 9 E M 2 3 1 5 1
A 7 D 2 2 R A 2 9 E M 2 3 2 5 1
A 7 D 2 2 R A 2 9 F 5 2
A 7 D 2 2 R A 2 9 F M 2 3 1 5 1
A 7 D 2 2 R A 2 9 F M 2 3 2 5 1
A 7 D 2 2 W W 2 9 A 3 4 9
A 7 D 2 2 W W 2 9 B 3 4 9
A 7 D 2 5 D S 2 9 A 2 2 - 1 4 3 7 2 6 8 - 1 4 9
A 7 D 2 5 D S 2 9 B 2 4 9
A 7 D 2 5 D S 2 9 C 2 4 9
A 7 D 2 5 D S 2 9 D 2 4 9
A 7 D 2 5 D S 2 9 E 2 4 9
A 7 D 2 5 R A 2 9 A 5 2
A 7 D 2 5 R A 2 9 A M 2 3 1 5 1
A 7 D 2 5 R A 2 9 A M 2 3 2 5 1
A 7 D 2 5 R A 2 9 C 5 2
A 7 D 2 5 R A 2 9 C M 2 3 1 5 1
A 7 D 2 5 R A 2 9 C M 2 3 2 5 1
A 7 D 2 5 R A 2 9 E 5 2
A 7 D 2 5 R A 2 9 E M 2 3 1 5 1
A 7 D 2 5 R A 2 9 E M 2 3 2 5 1
A 7 D 2 5 R A 2 9 F 5 2
A 7 D 2 5 R A 2 9 F M 2 3 1 5 1
A 7 D 2 5 R A 2 9 F M 2 3 2 2 - 1 4 3 7 2 6 8 - 2 5 1
A 7 D 2 5 W W 2 9 A 3 4 9
A 7 D 2 5 W W 2 9 B 3 4 9
A 7 D 2 8 D S 2 9 A 2 2 - 1 4 3 7 2 6 8 - 3 4 9
A 7 D 2 8 D S 2 9 B 2 2 - 1 4 3 7 2 6 8 - 4 4 9
A 7 D 2 8 D S 2 9 C 2 2 - 1 4 3 7 2 6 8 - 5 4 9
A 7 D 2 8 R A 2 9 A 5 2
A 7 D 2 8 R A 2 9 A M 2 3 1 2 - 1 4 3 7 2 6 8 - 8 5 1
A 7 D 2 8 R A 2 9 A M 2 3 2 5 1
A 7 D 2 8 R A 2 9 C 2 - 1 4 3 7 2 6 8 - 9 5 2
A 7 D 2 8 R A 2 9 C M 2 3 1 5 1
A 7 D 2 8 R A 2 9 C M 2 3 2 3 - 1 4 3 7 2 6 8 - 0 5 1
A 7 D 2 8 R A 2 9 E 3 - 1 4 3 7 2 6 8 - 1 5 2
A 7 D 2 8 R A 2 9 E M 2 3 1 3 - 1 4 3 7 2 6 8 - 2 5 1
A 7 D 2 8 R A 2 9 E M 2 3 2 5 1
A 7 D 2 8 R A 2 9 F 5 2
A 7 D 2 8 R A 2 9 F M 2 3 1 5 1
A 7 D 2 8 R A 2 9 F M 2 3 2 5 1
A 7 D 2 8 W W 2 9 A 3 3 - 1 4 3 7 2 6 8 - 3 4 9
A 7 D 2 8 W W 2 9 B 3 4 9
A 7 D 3 0 D S 2 9 A 2 3 - 1 4 3 7 2 6 8 - 4 4 9
A 7 D 3 0 D S 2 9 B 2 4 9
A 7 D 3 0 D S 2 9 C 2 3 - 1 4 3 7 2 6 8 - 5 4 9
A 7 D 3 0 D S 2 9 D 2 4 9
A 7 D 3 0 D S 2 9 E 2 4 9
A 7 D 3 0 R A 2 9 A 5 2
A 7 D 3 0 R A 2 9 A M 2 3 1 3 - 1 4 3 7 2 6 8 - 6 5 1
A 7 D 3 0 R A 2 9 A M 2 3 2 5 1
A 7 D 3 0 R A 2 9 C 5 2
A 7 D 3 0 R A 2 9 C M 2 3 1 5 1
A 7 D 3 0 R A 2 9 C M 2 3 2 5 1
A 7 D 3 0 R A 2 9 E 5 2
A 7 D 3 0 R A 2 9 E M 2 3 1 5 1
A 7 D 3 0 R A 2 9 E M 2 3 2 5 1
A 7 D 3 0 R A 2 9 F 5 2
A 7 D 3 0 R A 2 9 F M 2 3 1 5 1
A 7 D 3 0 R A 2 9 F M 2 3 2 5 1
A 7 D 3 0 W W 2 9 A 3 3 - 1 4 3 7 2 6 8 - 7 4 9
A 7 D 3 0 W W 2 9 B 3 4 9
A 7 D 3 5 D S 2 9 A 2 3 - 1 4 3 7 2 6 8 - 8 4 9
A 7 D 3 5 D S 2 9 B 2 4 9
A 7 D 3 5 D S 2 9 C 2 3 - 1 4 3 7 2 6 8 - 9 4 9
A 7 D 3 5 R A 2 9 A 4 - 1 4 3 7 2 6 8 - 0 5 2
A 7 D 3 5 R A 2 9 A M 2 3 1 5 1
A 7 D 3 5 R A 2 9 A M 2 3 2 5 1
A 7 D 3 5 R A 2 9 C 5 2
A 7 D 3 5 R A 2 9 C M 2 3 1 5 1
A 7 D 3 5 R A 2 9 C M 2 3 2 5 1
A 7 D 3 5 R A 2 9 E 5 2
A 7 D 3 5 R A 2 9 E M 2 3 1 5 1
A 7 D 3 5 R A 2 9 E M 2 3 2 5 1
A 7 D 3 5 R A 2 9 F 5 2
A 7 D 3 5 R A 2 9 F M 2 3 1 5 1
A 7 D 3 5 R A 2 9 F M 2 3 2 5 1
A 7 D 3 5 W W 2 9 A 3 4 9
A 7 D 3 5 W W 2 9 B 3 4 9
A 7 D 3 6 D S 2 9 A 2 4 - 1 4 3 7 2 6 8 - 1 4 9
A 7 D 3 6 D S 2 9 B 2 4 9
A 7 D 3 6 D S 2 9 C 2 4 - 1 4 3 7 2 6 8 - 2 4 9
A 7 D 3 6 R A 2 9 A 5 2
A 7 D 3 6 R A 2 9 A M 2 3 1 5 1
A 7 D 3 6 R A 2 9 A M 2 3 2 4 - 1 4 3 7 2 6 8 - 3 5 1
A 7 D 3 6 R A 2 9 C 5 2
A 7 D 3 6 R A 2 9 C M 2 3 1 5 1
A 7 D 3 6 R A 2 9 C M 2 3 2 5 1
A 7 D 3 6 R A 2 9 E 5 2
A 7 D 3 6 R A 2 9 E M 2 3 1 5 1
A 7 D 3 6 R A 2 9 E M 2 3 2 5 1
A 7 D 3 6 R A 2 9 F 5 2
A 7 D 3 6 R A 2 9 F M 2 3 1 5 1
A 7 D 3 6 R A 2 9 F M 2 3 2 5 1
A 7 D 3 6 W W 2 9 A 3 4 - 1 4 3 7 2 6 8 - 4 4 9
A 7 D 3 6 W W 2 9 B 3 4 9
A 7 D 4 0 D S 2 9 A 2 4 9
A 7 D 4 0 D S 2 9 B 2 4 9
A 7 D 4 0 D S 2 9 C 2 4 - 1 4 3 7 2 6 8 - 6 4 9
A 7 D 4 0 R A 2 9 A 5 2
A 7 D 4 0 R A 2 9 A M 2 3 1 5 1
A 7 D 4 0 R A 2 9 A M 2 3 2 5 1
A 7 D 4 0 R A 2 9 C 5 2
A 7 D 4 0 R A 2 9 C M 2 3 1 5 1
A 7 D 4 0 R A 2 9 C M 2 3 2 5 1
A 7 D 4 0 R A 2 9 E 4 - 1 4 3 7 2 6 8 - 8 5 2
A 7 D 4 0 R A 2 9 E M 2 3 1 5 1
A 7 D 4 0 R A 2 9 E M 2 3 2 5 1
A 7 D 4 0 R A 2 9 F 5 2
A 7 D 4 0 R A 2 9 F M 2 3 1 5 1
A 7 D 4 0 R A 2 9 F M 2 3 2 5 1
A 7 D 4 0 W W 2 9 A 3 4 - 1 4 3 7 2 6 8 - 9 4 9
A 7 D 4 0 W W 2 9 B 3 5 - 1 4 3 7 2 6 8 - 0 4 9
A 7 D 4 3 D S 2 9 A 2 5 - 1 4 3 7 2 6 8 - 2 4 9
A 7 D 4 3 D S 2 9 B 2 4 9
A 7 D 4 3 D S 2 9 C 2 5 - 1 4 3 7 2 6 8 - 3 4 9
A 7 D 4 3 R A 2 9 A 5 2
A 7 D 4 3 R A 2 9 A M 2 3 1 5 1
A 7 D 4 3 R A 2 9 A M 2 3 2 5 1
A 7 D 4 3 R A 2 9 C 5 2
A 7 D 4 3 R A 2 9 C M 2 3 1 5 1
A 7 D 4 3 R A 2 9 C M 2 3 2 5 1
A 7 D 4 3 R A 2 9 E 5 2
A 7 D 4 3 R A 2 9 E M 2 3 1 5 1
A 7 D 4 3 R A 2 9 E M 2 3 2 5 1
A 7 D 4 3 R A 2 9 F 5 2
A 7 D 4 3 R A 2 9 F M 2 3 1 5 1
A 7 D 4 3 R A 2 9 F M 2 3 2 5 1
A 7 D 4 3 W W 2 9 A 3 5 - 1 4 3 7 2 6 8 - 4 4 9
A 7 D 4 3 W W 2 9 B 3 4 9
A 7 D 5 0 D S 2 9 A 2 5 - 1 4 3 7 2 6 8 - 5 4 9
A 7 D 5 0 D S 2 9 B 2 4 9
A 7 D 5 0 D S 2 9 C 2 5 - 1 4 3 7 2 6 8 - 6 4 9
A 7 D 5 0 D S 2 9 D 2 5 - 1 4 3 7 2 6 8 - 8 4 9
A 7 D 5 0 D S 2 9 E 2 4 9
A 7 D 5 0 R A 2 9 A 6 - 1 4 3 7 2 6 8 - 0 5 2
A 7 D 5 0 R A 2 9 A M 2 3 1 5 1
A 7 D 5 0 R A 2 9 A M 2 3 2 5 1
A 7 D 5 0 R A 2 9 C 5 2
A 7 D 5 0 R A 2 9 C M 2 3 1 5 1
A 7 D 5 0 R A 2 9 C M 2 3 2 5 1
A 7 D 5 0 R A 2 9 E 5 2
A 7 D 5 0 R A 2 9 E M 2 3 1 5 1
A 7 D 5 0 R A 2 9 E M 2 3 2 5 1
A 7 D 5 0 R A 2 9 F 5 2
A 7 D 5 0 R A 2 9 F M 2 3 1 5 1
A 7 D 5 0 R A 2 9 F M 2 3 2 5 1
A 7 D 5 0 W W 2 9 A 3 6 - 1 4 3 7 2 6 8 - 1 4 9
A 7 D 5 0 W W 2 9 B 3 6 - 1 4 3 7 2 6 8 - 2 4 9
A 8 D 1 0 D S 2 9 A 2 1 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 1 0 D S 2 9 A 3 4 3
A 8 D 1 0 D S 2 9 B 2 4 3
A 8 D 1 0 D S 2 9 B 3 4 3
A 8 D 1 0 D S 2 9 C 2 2 - 1 4 3 7 2 6 9 - 0 4 3
A 8 D 1 0 D S 2 9 C 3 4 3
A 8 D 1 0 D S 2 9 D 2 4 3
A 8 D 1 0 D S 2 9 D 3 4 3
A 8 D 1 0 D S 2 9 E 2 4 3
A 8 D 1 0 D S 2 9 E 3 4 3
A 8 D 1 0 R A 2 9 A 2 - 1 4 3 7 2 6 9 - 1 4 6
A 8 D 1 0 R A 2 9 A M 2 3 3 4 7
A 8 D 1 0 R A 2 9 C 2 - 1 4 3 7 2 6 9 - 2 4 6
A 8 D 1 0 R A 2 9 C M 2 3 3 2 - 1 4 3 7 2 6 9 - 3 4 7
A 8 D 1 0 R A 2 9 E 2 - 1 4 3 7 2 6 9 - 4 4 6
A 8 D 1 0 R A 2 9 E M 2 3 3 4 7
A 8 D 1 0 R A 2 9 F 4 6
A 8 D 1 0 R A 2 9 F M 2 3 3 4 7
A 8 D 1 0 W W 2 9 A 3 2 - 1 4 3 7 2 6 9 - 5 4 4
A 8 D 1 0 W W 2 9 B 3 4 4
A 8 D 1 2 D S 2 9 A 2 2 - 1 4 3 7 2 6 9 - 7 4 3
A 8 D 1 2 D S 2 9 A 3 4 3
A 8 D 1 2 D S 2 9 B 2 4 3
A 8 D 1 2 D S 2 9 B 3 4 3
A 8 D 1 2 D S 2 9 C 2 2 - 1 4 3 7 2 6 9 - 8 4 3
A 8 D 1 2 D S 2 9 C 3 4 3
A 8 D 1 2 R A 2 9 A 4 6
A 8 D 1 2 R A 2 9 A M 2 3 3 4 7
A 8 D 1 2 R A 2 9 C 2 - 1 4 3 7 2 6 9 - 9 4 6
A 8 D 1 2 R A 2 9 C M 2 3 3 4 7
A 8 D 1 2 R A 2 9 E 3 - 1 4 3 7 2 6 9 - 0 4 6
A 8 D 1 2 R A 2 9 E M 2 3 3 3 - 1 4 3 7 2 6 9 - 1 4 7
A 8 D 1 2 W W 2 9 A 3 3 - 1 4 3 7 2 6 9 - 2 4 4
A 8 D 1 2 W W 2 9 B 3 4 4
A 8 D 1 5 D S 2 9 A 2 3 - 1 4 3 7 2 6 9 - 8 4 3
A 8 D 1 5 D S 2 9 A 3 4 3
A 8 D 1 5 D S 2 9 B 2 4 3
A 8 D 1 5 D S 2 9 B 3 4 3
A 8 D 1 5 D S 2 9 C 2 3 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 1 5 D S 2 9 C 3 4 3
A 8 D 1 5 D S 2 9 D 2 4 - 1 4 3 7 2 6 9 - 0 4 3
A 8 D 1 5 D S 2 9 D 3 4 3
A 8 D 1 5 D S 2 9 E 2 4 3
A 8 D 1 5 D S 2 9 E 3 4 3
A 8 D 1 5 R A 2 9 A 4 6
A 8 D 1 5 R A 2 9 A M 2 3 3 4 7
A 8 D 1 5 R A 2 9 C 4 - 1 4 3 7 2 6 9 - 1 4 6
A 8 D 1 5 R A 2 9 C M 2 3 3 4 - 1 4 3 7 2 6 9 - 2 4 7
A 8 D 1 5 R A 2 9 E 4 - 1 4 3 7 2 6 9 - 3 4 6
A 8 D 1 5 R A 2 9 E M 2 3 3 4 - 1 4 3 7 2 6 9 - 4 4 7
A 8 D 1 5 R A 2 9 F 4 6
A 8 D 1 5 R A 2 9 F M 2 3 3 4 - 1 4 3 7 2 6 9 - 5 4 7
A 8 D 1 5 W W 2 9 A 3 4 - 1 4 3 7 2 6 9 - 6 4 4
A 8 D 1 5 W W 2 9 B 3 4 4
A 8 D 1 8 D S 2 9 A 2 4 - 1 4 3 7 2 6 9 - 8 4 3
A 8 D 1 8 D S 2 9 A 3 4 3
A 8 D 1 8 D S 2 9 B 2 4 3
A 8 D 1 8 D S 2 9 B 3 4 3
A 8 D 1 8 D S 2 9 C 2 4 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 1 8 D S 2 9 C 3 5 - 1 4 3 7 2 6 9 - 0 4 3
A 8 D 1 8 D S 2 9 D 2 4 3
A 8 D 1 8 D S 2 9 D 3 4 3
A 8 D 1 8 D S 2 9 E 2 4 3
A 8 D 1 8 D S 2 9 E 3 4 3
A 8 D 1 8 R A 2 9 A 4 6
A 8 D 1 8 R A 2 9 A M 2 3 3 4 7
A 8 D 1 8 R A 2 9 C 5 - 1 4 3 7 2 6 9 - 1 4 6
A 8 D 1 8 R A 2 9 C M 2 3 3 5 - 1 4 3 7 2 6 9 - 2 4 7
A 8 D 1 8 R A 2 9 E 4 6
A 8 D 1 8 R A 2 9 E M 2 3 3 4 7
A 8 D 1 8 R A 2 9 F 4 6
A 8 D 1 8 R A 2 9 F M 2 3 3 5 - 1 4 3 7 2 6 9 - 3 4 7
A 8 D 1 8 W W 2 9 A 3 5 - 1 4 3 7 2 6 9 - 4 4 4
A 8 D 1 8 W W 2 9 B 3 4 4
A 8 D 2 0 D S 2 9 A 2 4 3
A 8 D 2 0 D S 2 9 A 3 4 3
A 8 D 2 0 D S 2 9 B 2 5 - 1 4 3 7 2 6 9 - 6 4 3
A 8 D 2 0 D S 2 9 B 3 4 3
A 8 D 2 0 D S 2 9 C 2 5 - 1 4 3 7 2 6 9 - 7 4 3
A 8 D 2 0 D S 2 9 C 3 4 3
A 8 D 2 0 R A 2 9 A 4 6
A 8 D 2 0 R A 2 9 A M 2 3 3 4 7
A 8 D 2 0 R A 2 9 C 5 - 1 4 3 7 2 6 9 - 8 4 6
A 8 D 2 0 R A 2 9 C M 2 3 3 4 7
A 8 D 2 0 R A 2 9 E 5 - 1 4 3 7 2 6 9 - 9 4 6
A 8 D 2 0 R A 2 9 E M 2 3 3 4 7
A 8 D 2 0 W W 2 9 A 3 6 - 1 4 3 7 2 6 9 - 0 4 4
A 8 D 2 0 W W 2 9 B 3 4 4
A 8 D 2 2 D S 2 9 A 2 6 - 1 4 3 7 2 6 9 - 1 4 3
A 8 D 2 2 D S 2 9 A 3 4 3
A 8 D 2 2 D S 2 9 B 2 4 3
A 8 D 2 2 D S 2 9 B 3 4 3
A 8 D 2 2 D S 2 9 C 2 6 - 1 4 3 7 2 6 9 - 2 4 3
A 8 D 2 2 D S 2 9 C 3 4 3
A 8 D 2 2 R A 2 9 A 6 - 1 4 3 7 2 6 9 - 4 4 6
A 8 D 2 2 R A 2 9 A M 2 3 3 4 7
A 8 D 2 2 R A 2 9 C 6 - 1 4 3 7 2 6 9 - 5 4 6
A 8 D 2 2 R A 2 9 C M 2 3 3 4 7
A 8 D 2 2 R A 2 9 E 6 - 1 4 3 7 2 6 9 - 6 4 6
A 8 D 2 2 R A 2 9 E M 2 3 3 6 - 1 4 3 7 2 6 9 - 7 4 7
A 8 D 2 2 W W 2 9 A 3 6 - 1 4 3 7 2 6 9 - 8 4 4
A 8 D 2 2 W W 2 9 B 3 4 4
A 8 D 2 5 D S 2 9 A 2 6 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 2 5 D S 2 9 A 3 4 3
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
195
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
A 8 D 2 5 D S 2 9 B 2 7 - 1 4 3 7 2 6 9 - 0 4 3
A 8 D 2 5 D S 2 9 B 3 4 3
A 8 D 2 5 D S 2 9 C 2 7 - 1 4 3 7 2 6 9 - 1 4 3
A 8 D 2 5 D S 2 9 C 3 7 - 1 4 3 7 2 6 9 - 2 4 3
A 8 D 2 5 D S 2 9 D 2 4 3
A 8 D 2 5 D S 2 9 D 3 4 3
A 8 D 2 5 D S 2 9 E 2 4 3
A 8 D 2 5 D S 2 9 E 3 4 3
A 8 D 2 5 R A 2 9 A 7 - 1 4 3 7 2 6 9 - 3 4 6
A 8 D 2 5 R A 2 9 A M 2 3 3 7 - 1 4 3 7 2 6 9 - 4 4 7
A 8 D 2 5 R A 2 9 C 7 - 1 4 3 7 2 6 9 - 5 4 6
A 8 D 2 5 R A 2 9 C M 2 3 3 7 - 1 4 3 7 2 6 9 - 6 4 7
A 8 D 2 5 R A 2 9 E 7 - 1 4 3 7 2 6 9 - 7 4 6
A 8 D 2 5 R A 2 9 E M 2 3 3 4 7
A 8 D 2 5 R A 2 9 F 4 6
A 8 D 2 5 R A 2 9 F M 2 3 3 7 - 1 4 3 7 2 6 9 - 8 4 7
A 8 D 2 5 W W 2 9 A 3 7 - 1 4 3 7 2 6 9 - 9 4 4
A 8 D 2 5 W W 2 9 B 3 4 4
A 8 D 2 8 D S 2 9 A 2 8 - 1 4 3 7 2 6 9 - 1 4 3
A 8 D 2 8 D S 2 9 A 3 4 3
A 8 D 2 8 D S 2 9 B 2 4 3
A 8 D 2 8 D S 2 9 B 3 4 3
A 8 D 2 8 D S 2 9 C 2 8 - 1 4 3 7 2 6 9 - 2 4 3
A 8 D 2 8 D S 2 9 C 3 4 3
A 8 D 2 8 R A 2 9 A 4 6
A 8 D 2 8 R A 2 9 A M 2 3 3 4 7
A 8 D 2 8 R A 2 9 C 6 - 1 4 3 7 2 7 0 - 6 4 6
A 8 D 2 8 R A 2 9 C M 2 3 3 4 7
A 8 D 2 8 R A 2 9 E 8 - 1 4 3 7 2 6 9 - 3 4 6
A 8 D 2 8 R A 2 9 E M 2 3 3 4 7
A 8 D 2 8 W W 2 9 A 3 4 4
A 8 D 2 8 W W 2 9 B 3 4 4
A 8 D 3 0 D S 2 9 A 2 8 - 1 4 3 7 2 6 9 - 5 4 3
A 8 D 3 0 D S 2 9 A 3 4 3
A 8 D 3 0 D S 2 9 B 2 8 - 1 4 3 7 2 6 9 - 6 4 3
A 8 D 3 0 D S 2 9 B 3 4 3
A 8 D 3 0 D S 2 9 C 2 8 - 1 4 3 7 2 6 9 - 7 4 3
A 8 D 3 0 D S 2 9 C 3 8 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 3 0 D S 2 9 D 2 9 - 1 4 3 7 2 6 9 - 0 4 3
A 8 D 3 0 D S 2 9 D 2 9 - 1 4 3 7 2 6 9 - 1 4 3
A 8 D 3 0 D S 2 9 D 3 4 3
A 8 D 3 0 D S 2 9 E 2 4 3
A 8 D 3 0 D S 2 9 E 3 4 3
A 8 D 3 0 R A 2 9 A 4 6
A 8 D 3 0 R A 2 9 A M 2 3 3 4 7
A 8 D 3 0 R A 2 9 C 9 - 1 4 3 7 2 6 9 - 2 4 6
A 8 D 3 0 R A 2 9 C M 2 3 3 4 7
A 8 D 3 0 R A 2 9 E 9 - 1 4 3 7 2 6 9 - 3 4 6
A 8 D 3 0 R A 2 9 E M 2 3 3 4 7
A 8 D 3 0 R A 2 9 F 4 6
A 8 D 3 0 R A 2 9 F M 2 3 3 4 7
A 8 D 3 0 W W 2 9 A 3 9 - 1 4 3 7 2 6 9 - 4 4 4
A 8 D 3 0 W W 2 9 B 3 9 - 1 4 3 7 2 6 9 - 5 4 4
A 8 D 3 1 D S 2 9 A 2 9 - 1 4 3 7 2 6 9 - 8 4 3
A 8 D 3 1 D S 2 9 A 3 9 - 1 4 3 7 2 6 9 - 9 4 3
A 8 D 3 1 D S 2 9 B 2 4 3
A 8 D 3 1 D S 2 9 B 3 0 - 1 4 3 7 2 7 0 - 1 4 3
A 8 D 3 1 D S 2 9 C 2 0 - 1 4 3 7 2 7 0 - 2 4 3
A 8 D 3 1 D S 2 9 C 3 4 3
A 8 D 3 1 D S 2 9 D 2 0 - 1 4 3 7 2 7 0 - 3 4 3
A 8 D 3 1 D S 2 9 D 3 4 3
A 8 D 3 1 D S 2 9 E 2 4 3
A 8 D 3 1 D S 2 9 E 3 4 3
A 8 D 3 1 R A 2 9 A 0 - 1 4 3 7 2 7 0 - 4 4 6
A 8 D 3 1 R A 2 9 A M 2 3 3 4 7
A 8 D 3 1 R A 2 9 C 0 - 1 4 3 7 2 7 0 - 6 4 6
A 8 D 3 1 R A 2 9 C M 2 3 3 0 - 1 4 3 7 2 7 0 - 7 4 7
A 8 D 3 1 R A 2 9 E 0 - 1 4 3 7 2 7 0 - 8 4 6
A 8 D 3 1 R A 2 9 E M 2 3 3 4 7
A 8 D 3 1 R A 2 9 F 0 - 1 4 3 7 2 7 0 - 9 4 6
A 8 D 3 1 R A 2 9 F M 2 3 3 4 7
A 8 D 3 1 W W 2 9 A 3 1 - 1 4 3 7 2 7 0 - 0 4 4
A 8 D 3 1 W W 2 9 B 3 4 4
A 8 D 3 5 D S 2 9 A 2 1 - 1 4 3 7 2 7 0 - 2 4 3
A 8 D 3 5 D S 2 9 A 3 4 3
A 8 D 3 5 D S 2 9 B 2 4 3
A 8 D 3 5 D S 2 9 B 3 4 3
A 8 D 3 5 D S 2 9 C 2 1 - 1 4 3 7 2 7 0 - 3 4 3
A 8 D 3 5 D S 2 9 C 3 4 3
A 8 D 3 5 R A 2 9 A 4 6
A 8 D 3 5 R A 2 9 A M 2 3 3 4 7
A 8 D 3 5 R A 2 9 C 1 - 1 4 3 7 2 7 0 - 4 4 6
A 8 D 3 5 R A 2 9 C M 2 3 3 4 7
A 8 D 3 5 R A 2 9 E 4 6
A 8 D 3 5 R A 2 9 E M 2 3 3 4 7
A 8 D 3 5 W W 2 9 A 3 1 - 1 4 3 7 2 7 0 - 5 4 4
A 8 D 3 5 W W 2 9 B 3 4 4
A 8 D 3 6 D S 2 9 A 2 1 - 1 4 3 7 2 7 0 - 6 4 3
A 8 D 3 6 D S 2 9 A 3 4 3
A 8 D 3 6 D S 2 9 B 2 4 3
A 8 D 3 6 D S 2 9 B 3 1 - 1 4 3 7 2 7 0 - 7 4 3
A 8 D 3 6 D S 2 9 C 2 1 - 1 4 3 7 2 7 0 - 8 4 3
A 8 D 3 6 D S 2 9 C 3 1 - 1 4 3 7 2 7 0 - 9 4 3
A 8 D 3 6 R A 2 9 A 2 - 1 4 3 7 2 7 0 - 0 4 6
A 8 D 3 6 R A 2 9 A M 2 3 3 4 7
A 8 D 3 6 R A 2 9 C 2 - 1 4 3 7 2 7 0 - 1 4 6
A 8 D 3 6 R A 2 9 C M 2 3 3 4 7
A 8 D 3 6 R A 2 9 E 2 - 1 4 3 7 2 7 0 - 2 4 6
A 8 D 3 6 R A 2 9 E M 2 3 3 2 - 1 4 3 7 2 7 0 - 3 4 7
A 8 D 3 6 W W 2 9 A 3 2 - 1 4 3 7 2 7 0 - 4 4 4
A 8 D 3 6 W W 2 9 B 3 4 4
A 8 D 4 0 D S 2 9 A 2 4 3
A 8 D 4 0 D S 2 9 A 3 2 - 1 4 3 7 2 7 0 - 6 4 3
A 8 D 4 0 D S 2 9 B 2 4 3
A 8 D 4 0 D S 2 9 B 3 4 3
A 8 D 4 0 D S 2 9 C 2 2 - 1 4 3 7 2 7 0 - 7 4 3
A 8 D 4 0 D S 2 9 C 3 4 3
A 8 D 4 0 R A 2 9 A 4 6
A 8 D 4 0 R A 2 9 A M 2 3 3 4 7
A 8 D 4 0 R A 2 9 C 4 6
A 8 D 4 0 R A 2 9 C M 2 3 3 4 7
A 8 D 4 0 R A 2 9 E 2 - 1 4 3 7 2 7 0 - 8 4 6
A 8 D 4 0 R A 2 9 E M 2 3 3 4 7
A 8 D 4 0 W W 2 9 A 3 2 - 1 4 3 7 2 7 0 - 9 4 4
A 8 D 4 0 W W 2 9 B 3 4 4
A 8 D 4 3 D S 2 9 A 2 4 3
A 8 D 4 3 D S 2 9 A 3 4 3
A 8 D 4 3 D S 2 9 B 2 4 3
A 8 D 4 3 D S 2 9 B 3 4 3
A 8 D 4 3 D S 2 9 C 2 3 - 1 4 3 7 2 7 0 - 0 4 3
A 8 D 4 3 D S 2 9 C 3 4 3
A 8 D 4 3 R A 2 9 A 3 - 1 4 3 7 2 7 0 - 1 4 6
A 8 D 4 3 R A 2 9 A M 2 3 3 4 7
A 8 D 4 3 R A 2 9 C 3 - 1 4 3 7 2 7 0 - 2 4 6
A 8 D 4 3 R A 2 9 C M 2 3 3 4 7
A 8 D 4 3 R A 2 9 E 3 - 1 4 3 7 2 7 0 - 3 4 6
A 8 D 4 3 R A 2 9 E M 2 3 3 4 7
A 8 D 4 3 W W 2 9 A 3 3 - 1 4 3 7 2 7 0 - 4 4 4
A 8 D 4 3 W W 2 9 B 3 4 4
A 8 D 4 4 D S 2 9 A 2 3 - 1 4 3 7 2 7 0 - 5 4 3
A 8 D 4 4 D S 2 9 A 3 4 4
A 8 D 4 4 D S 2 9 B 2 4 3
A 8 D 4 4 D S 2 9 B 3 4 4
A 8 D 4 4 D S 2 9 C 2 3 - 1 4 3 7 2 7 0 - 6 4 3
A 8 D 4 4 D S 2 9 C 3 3 - 1 4 3 7 2 7 0 - 7 4 4
A 8 D 4 4 R A 2 9 A 4 6
A 8 D 4 4 R A 2 9 A M 2 3 3 4 7
A 8 D 4 4 R A 2 9 C 4 6
A 8 D 4 4 R A 2 9 C M 2 3 3 3 - 1 4 3 7 2 7 0 - 8 4 7
A 8 D 4 4 R A 2 9 E 4 6
A 8 D 4 4 R A 2 9 E M 2 3 3 4 7
A 8 D 4 4 W W 2 9 A 3 4 4
A 8 D 4 4 W W 2 9 B 3 4 4
A 8 D 5 0 D S 2 9 A 2 3 - 1 4 3 7 2 7 0 - 9 4 3
A 8 D 5 0 D S 2 9 A 3 4 4
A 8 D 5 0 D S 2 9 B 2 4 3
A 8 D 5 0 D S 2 9 B 3 4 4
A 8 D 5 0 D S 2 9 C 2 4 - 1 4 3 7 2 7 0 - 0 4 3
A 8 D 5 0 D S 2 9 C 3 4 - 1 4 3 7 2 7 0 - 1 4 4
A 8 D 5 0 D S 2 9 D 2 4 - 1 4 3 7 2 7 0 - 2 4 3
A 8 D 5 0 D S 2 9 D 3 4 4
A 8 D 5 0 D S 2 9 E 2 4 3
A 8 D 5 0 D S 2 9 E 3 4 4
A 8 D 5 0 R A 2 9 A 4 6
A 8 D 5 0 R A 2 9 A M 2 3 3 4 7
A 8 D 5 0 R A 2 9 C 4 - 1 4 3 7 2 7 0 - 4 4 6
A 8 D 5 0 R A 2 9 C M 2 3 3 4 7
A 8 D 5 0 R A 2 9 E 4 - 1 4 3 7 2 7 0 - 5 4 6
A 8 D 5 0 R A 2 9 E M 2 3 3 4 7
A 8 D 5 0 R A 2 9 F 4 - 1 4 3 7 2 7 0 - 6 4 6
A 8 D 5 0 R A 2 9 F M 2 3 3 4 7
A 8 D 5 0 W W 2 9 A 3 4 - 1 4 3 7 2 7 0 - 7 4 4
A 8 D 5 0 W W 2 9 B 3 4 4
A 8 D 6 0 D S 2 9 A 2 5 - 1 4 3 7 2 7 0 - 1 4 3
A 8 D 6 0 D S 2 9 A 3 4 4
A 8 D 6 0 D S 2 9 B 2 4 3
A 8 D 6 0 D S 2 9 B 3 4 4
A 8 D 6 0 D S 2 9 C 2 5 - 1 4 3 7 2 7 0 - 2 4 3
A 8 D 6 0 D S 2 9 C 3 5 - 1 4 3 7 2 7 0 - 3 4 4
A 8 D 6 0 R A 2 9 A 5 - 1 4 3 7 2 7 0 - 5 4 6
A 8 D 6 0 R A 2 9 A M 2 3 3 4 7
A 8 D 6 0 R A 2 9 C 4 6
A 8 D 6 0 R A 2 9 C M 2 3 3 4 7
A 8 D 6 0 R A 2 9 E 4 6
A 8 D 6 0 R A 2 9 E M 2 3 3 4 7
A 8 D 6 0 W W 2 9 A 3 5 - 1 4 3 7 2 7 0 - 6 4 4
A 8 D 6 0 W W 2 9 B 3 4 4
A 8 D 6 5 D S 2 9 A 2 4 3
A 8 D 6 5 D S 2 9 A 3 4 4
A 8 D 6 5 D S 2 9 B 2 4 3
A 8 D 6 5 D S 2 9 B 3 4 4
A 8 D 6 5 D S 2 9 C 2 5 - 1 4 3 7 2 7 0 - 9 4 3
A 8 D 6 5 D S 2 9 C 3 4 4
A 8 D 6 5 D S 2 9 D 2 6 - 1 4 3 7 2 7 0 - 0 4 3
A 8 D 6 5 D S 2 9 D 3 4 4
A 8 D 6 5 D S 2 9 E 2 4 3
A 8 D 6 5 D S 2 9 E 3 4 4
A 8 D 6 5 R A 2 9 A 4 6
A 8 D 6 5 R A 2 9 A M 2 3 3 4 7
A 8 D 6 5 R A 2 9 C 4 6
A 8 D 6 5 R A 2 9 C M 2 3 3 4 7
A 8 D 6 5 R A 2 9 E 4 6
A 8 D 6 5 R A 2 9 E M 2 3 3 4 7
A 8 D 6 5 R A 2 9 F 4 6
A 8 D 6 5 R A 2 9 F M 2 3 3 4 7
A 8 D 6 5 W W 2 9 A 3 4 4
A 8 D 6 5 W W 2 9 B 3 4 4
C 1 D 1 8 P F 2 9 0 1 3 1 3 1
C 1 D 1 8 P F 2 9 0 1 5 0 - 1 4 3 7 2 6 4 - 3 1 3 1
C 1 D 1 8 P F 2 9 0 1 7 1 3 2
C 1 D 1 8 P F 2 9 0 4 3 1 3 1
C 1 D 1 8 P F 2 9 0 4 5 1 3 1
C 1 D 1 8 P F 2 9 0 4 7 1 3 2
C 1 D 1 8 P F 2 9 1 3 3 1 3 1
C 1 D 1 8 P F 2 9 1 3 5 1 3 1
C 1 D 1 8 P F 2 9 1 3 7 1 3 2
C 1 D 2 0 P F 2 9 0 1 3 1 3 1
C 1 D 2 0 P F 2 9 0 1 5 0 - 1 4 3 7 2 6 4 - 6 1 3 1
C 1 D 2 0 P F 2 9 0 1 7 1 3 2
C 1 D 2 0 P F 2 9 0 4 3 0 - 1 4 3 7 2 6 4 - 7 1 3 1
C 1 D 2 0 P F 2 9 0 4 5 1 3 1
C 1 D 2 0 P F 2 9 0 4 7 1 3 2
C 1 D 2 0 P F 2 9 1 3 3 1 3 1
C 1 D 2 0 P F 2 9 1 3 5 1 3 1
C 1 D 2 0 P F 2 9 1 3 7 1 3 2
C 1 D 2 2 P F 2 9 0 1 3 1 3 1
C 1 D 2 2 P F 2 9 0 1 5 1 3 1
C 1 D 2 2 P F 2 9 0 1 7 1 3 2
C 1 D 2 2 P F 2 9 0 4 3 1 3 1
C 1 D 2 2 P F 2 9 0 4 5 1 3 1
C 1 D 2 2 P F 2 9 0 4 7 1 3 2
C 1 D 2 2 P F 2 9 1 3 3 1 3 1
C 1 D 2 2 P F 2 9 1 3 5 1 3 1
C 1 D 2 2 P F 2 9 1 3 7 1 3 2
C 1 D 2 5 P F 2 9 0 1 3 0 - 1 4 3 7 2 6 4 - 9 1 3 1
C 1 D 2 5 P F 2 9 0 1 5 1 - 1 4 3 7 2 6 4 - 0 1 3 1
C 1 D 2 5 P F 2 9 0 1 7 1 3 2
C 1 D 2 5 P F 2 9 0 4 3 1 3 1
C 1 D 2 5 P F 2 9 0 4 5 1 3 1
C 1 D 2 5 P F 2 9 0 4 7 1 3 2
C 1 D 2 5 P F 2 9 1 3 3 1 3 1
C 1 D 2 5 P F 2 9 1 3 5 1 3 1
C 1 D 2 5 P F 2 9 1 3 7 1 3 2
C 1 D 2 8 P F 2 9 0 1 3 1 3 1
C 1 D 2 8 P F 2 9 0 1 5 1 3 1
C 1 D 2 8 P F 2 9 0 1 7 1 3 2
C 1 D 2 8 P F 2 9 0 4 3 1 3 1
C 1 D 2 8 P F 2 9 0 4 5 1 3 1
C 1 D 2 8 P F 2 9 0 4 7 1 3 2
C 1 D 2 8 P F 2 9 1 3 3 1 3 1
C 1 D 2 8 P F 2 9 1 3 5 1 3 1
C 1 D 2 8 P F 2 9 1 3 7 1 3 2
C 1 D 3 0 P F 2 9 0 1 3 1 3 1
C 1 D 3 0 P F 2 9 0 1 5 1 3 1
C 1 D 3 0 P F 2 9 0 1 7 1 3 2
C 1 D 3 0 P F 2 9 0 4 3 1 3 1
C 1 D 3 0 P F 2 9 0 4 5 1 3 1
C 1 D 3 0 P F 2 9 0 4 7 1 3 2
C 1 D 3 0 P F 2 9 1 3 3 1 3 1
C 1 D 3 0 P F 2 9 1 3 5 1 3 1
C 1 D 3 0 P F 2 9 1 3 7 1 3 2
C 1 D 3 5 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 4 - 5 1 3 1
C 1 D 3 5 P F 2 9 0 1 5 1 - 1 4 3 7 2 6 4 - 6 1 3 1
C 1 D 3 5 P F 2 9 0 1 7 1 3 2
C 1 D 3 5 P F 2 9 0 4 3 1 3 1
C 1 D 3 5 P F 2 9 0 4 5 1 3 1
C 1 D 3 5 P F 2 9 0 4 7 1 3 2
C 1 D 3 5 P F 2 9 1 3 3 1 3 1
C 1 D 3 5 P F 2 9 1 3 5 1 3 1
C 1 D 3 5 P F 2 9 1 3 7 1 3 2
C 1 D 3 6 P F 2 9 0 1 3 1 3 1
C 1 D 3 6 P F 2 9 0 1 5 1 3 1
C 1 D 3 6 P F 2 9 0 1 7 1 3 2
C 1 D 3 6 P F 2 9 0 4 3 1 3 1
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
196
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 1 D 3 6 P F 2 9 0 4 5 1 3 1
C 1 D 3 6 P F 2 9 0 4 7 1 3 2
C 1 D 3 6 P F 2 9 1 3 3 1 3 1
C 1 D 3 6 P F 2 9 1 3 5 1 3 1
C 1 D 3 6 P F 2 9 1 3 7 1 3 2
C 1 D 4 0 P F 2 9 0 1 3 1 3 1
C 1 D 4 0 P F 2 9 0 1 5 1 3 1
C 1 D 4 0 P F 2 9 0 1 7 1 3 2
C 1 D 4 0 P F 2 9 0 4 3 1 3 1
C 1 D 4 0 P F 2 9 0 4 5 1 3 1
C 1 D 4 0 P F 2 9 0 4 7 1 3 2
C 1 D 4 0 P F 2 9 1 3 3 1 3 1
C 1 D 4 0 P F 2 9 1 3 5 1 3 1
C 1 D 4 0 P F 2 9 1 3 7 1 3 2
C 1 D 4 3 P F 2 9 0 1 3 1 3 1
C 1 D 4 3 P F 2 9 0 1 5 1 3 1
C 1 D 4 3 P F 2 9 0 1 7 1 3 2
C 1 D 4 3 P F 2 9 0 4 3 1 3 1
C 1 D 4 3 P F 2 9 0 4 5 1 3 1
C 1 D 4 3 P F 2 9 0 4 7 1 3 2
C 1 D 4 3 P F 2 9 1 3 3 1 3 1
C 1 D 4 3 P F 2 9 1 3 5 1 3 1
C 1 D 4 3 P F 2 9 1 3 7 1 3 2
C 1 D 4 5 P F 2 9 0 1 3 1 3 1
C 1 D 4 5 P F 2 9 0 1 5 1 3 1
C 1 D 4 5 P F 2 9 0 1 7 1 3 2
C 1 D 4 5 P F 2 9 0 4 3 1 3 1
C 1 D 4 5 P F 2 9 0 4 5 1 3 1
C 1 D 4 5 P F 2 9 0 4 7 1 3 2
C 1 D 4 5 P F 2 9 1 3 3 1 3 1
C 1 D 4 5 P F 2 9 1 3 5 1 3 1
C 1 D 4 5 P F 2 9 1 3 7 1 3 2
C 1 D 5 0 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 4 - 2 1 3 1
C 1 D 5 0 P F 2 9 0 1 5 2 - 1 4 3 7 2 6 4 - 3 1 3 1
C 1 D 5 0 P F 2 9 0 1 7 2 - 1 4 3 7 2 6 4 - 4 1 3 2
C 1 D 5 0 P F 2 9 0 4 3 1 3 1
C 1 D 5 0 P F 2 9 0 4 5 1 3 1
C 1 D 5 0 P F 2 9 0 4 7 1 3 2
C 1 D 5 0 P F 2 9 1 3 3 1 3 1
C 1 D 5 0 P F 2 9 1 3 5 1 3 1
C 1 D 5 0 P F 2 9 1 3 7 1 3 2
C 1 D 6 0 P F 2 9 0 1 3 1 3 1
C 1 D 6 0 P F 2 9 0 1 5 1 3 1
C 1 D 6 0 P F 2 9 0 1 7 1 3 2
C 1 D 6 0 P F 2 9 0 4 3 1 3 1
C 1 D 6 0 P F 2 9 0 4 5 1 3 1
C 1 D 6 0 P F 2 9 0 4 7 1 3 2
C 1 D 6 0 P F 2 9 1 3 3 1 3 1
C 1 D 6 0 P F 2 9 1 3 5 1 3 1
C 1 D 6 0 P F 2 9 1 3 7 1 3 2
C 6 D 0 6 D S 2 9 A 1 1 - 1 4 3 7 2 7 3 - 3 3 9
C 6 D 0 6 D S 2 9 A 3 3 9
C 6 D 0 6 D S 2 9 A 4 4 0
C 6 D 0 6 D S 2 9 B 1 3 9
C 6 D 0 6 D S 2 9 B 3 3 9
C 6 D 0 6 D S 2 9 B 4 4 0
C 6 D 0 6 D S 2 9 C 1 1 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 0 6 D S 2 9 C 3 1 - 1 4 3 7 2 7 3 - 5 3 9
C 6 D 0 6 D S 2 9 C 4 4 0
C 6 D 0 6 D S 2 9 D 1 1 - 1 4 3 7 2 7 3 - 6 3 9
C 6 D 0 6 D S 2 9 D 3 1 - 1 4 3 7 2 7 3 - 7 3 9
C 6 D 0 6 D S 2 9 D 4 1 - 1 4 3 7 2 7 3 - 8 4 0
C 6 D 0 6 D S 2 9 E 1 3 9
C 6 D 0 6 D S 2 9 E 3 3 9
C 6 D 0 6 D S 2 9 E 4 4 0
C 6 D 0 6 P F 2 9 0 1 2 1 4 8
C 6 D 0 6 P F 2 9 0 1 3 0 - 1 4 3 7 2 6 2 - 4 1 4 8
C 6 D 0 6 P F 2 9 0 2 2 1 4 6
C 6 D 0 6 P F 2 9 0 2 3 1 4 6
C 6 D 0 6 P F 2 9 0 3 2 1 4 6
C 6 D 0 6 P F 2 9 0 3 3 1 4 6
C 6 D 0 6 P F 2 9 0 4 2 1 4 8
C 6 D 0 6 P F 2 9 0 4 3 0 - 1 4 3 7 2 6 2 - 5 1 4 8
C 6 D 0 6 P F 2 9 1 3 2 1 4 8
C 6 D 0 6 P F 2 9 1 3 3 1 4 8
C 6 D 0 6 P F 2 9 1 4 2 1 4 6
C 6 D 0 6 P F 2 9 1 4 3 1 4 6
C 6 D 1 0 D S 2 9 A 1 1 - 1 4 3 7 2 7 3 - 9 3 9
C 6 D 1 0 D S 2 9 A 3 3 9
C 6 D 1 0 D S 2 9 A 4 4 0
C 6 D 1 0 D S 2 9 B 1 3 9
C 6 D 1 0 D S 2 9 B 3 2 - 1 4 3 7 2 7 3 - 0 3 9
C 6 D 1 0 D S 2 9 B 4 4 0
C 6 D 1 0 D S 2 9 C 1 2 - 1 4 3 7 2 7 3 - 1 3 9
C 6 D 1 0 D S 2 9 C 3 3 9
C 6 D 1 0 D S 2 9 C 4 2 - 1 4 3 7 2 7 3 - 2 4 0
C 6 D 1 0 D S 2 9 D 1 3 9
C 6 D 1 0 D S 2 9 D 3 3 9
C 6 D 1 0 D S 2 9 D 4 4 0
C 6 D 1 0 D S 2 9 E 1 3 9
C 6 D 1 0 D S 2 9 E 3 3 9
C 6 D 1 0 D S 2 9 E 4 4 0
C 6 D 1 0 P F 2 9 0 1 2 1 4 8
C 6 D 1 0 P F 2 9 0 1 3 1 4 8
C 6 D 1 0 P F 2 9 0 2 2 0 - 1 4 3 7 2 6 2 - 6 1 4 6
C 6 D 1 0 P F 2 9 0 2 3 1 4 6
C 6 D 1 0 P F 2 9 0 3 2 1 4 6
C 6 D 1 0 P F 2 9 0 3 3 1 4 6
C 6 D 1 0 P F 2 9 0 4 2 1 4 8
C 6 D 1 0 P F 2 9 0 4 3 0 - 1 4 3 7 2 6 2 - 7 1 4 8
C 6 D 1 0 P F 2 9 1 3 2 1 4 8
C 6 D 1 0 P F 2 9 1 3 3 1 4 8
C 6 D 1 0 P F 2 9 1 4 2 1 4 6
C 6 D 1 0 P F 2 9 1 4 3 1 4 6
C 6 D 1 2 D S 2 9 A 1 3 9
C 6 D 1 2 D S 2 9 A 3 3 9
C 6 D 1 2 D S 2 9 A 4 2 - 1 4 3 7 2 7 3 - 3 4 0
C 6 D 1 2 D S 2 9 B 1 3 9
C 6 D 1 2 D S 2 9 B 3 3 9
C 6 D 1 2 D S 2 9 B 4 4 0
C 6 D 1 2 D S 2 9 C 1 2 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 1 2 D S 2 9 C 3 2 - 1 4 3 7 2 7 3 - 5 3 9
C 6 D 1 2 D S 2 9 C 4 4 0
C 6 D 1 2 D S 2 9 D 1 3 9
C 6 D 1 2 D S 2 9 D 3 3 9
C 6 D 1 2 D S 2 9 D 4 4 0
C 6 D 1 2 D S 2 9 E 1 3 9
C 6 D 1 2 D S 2 9 E 3 3 9
C 6 D 1 2 D S 2 9 E 4 4 0
C 6 D 1 2 P F 2 9 0 1 2 1 4 8
C 6 D 1 2 P F 2 9 0 1 3 1 4 8
C 6 D 1 2 P F 2 9 0 2 2 1 4 6
C 6 D 1 2 P F 2 9 0 2 3 1 4 6
C 6 D 1 2 P F 2 9 0 3 2 1 4 6
C 6 D 1 2 P F 2 9 0 3 3 1 4 6
C 6 D 1 2 P F 2 9 0 4 2 1 4 8
C 6 D 1 2 P F 2 9 0 4 3 1 4 8
C 6 D 1 2 P F 2 9 1 3 2 1 4 8
C 6 D 1 2 P F 2 9 1 3 3 1 4 8
C 6 D 1 2 P F 2 9 1 4 2 1 4 6
C 6 D 1 2 P F 2 9 1 4 3 1 4 6
C 6 D 1 5 D S 2 9 A 1 2 - 1 4 3 7 2 7 3 - 6 3 9
C 6 D 1 5 D S 2 9 A 3 3 9
C 6 D 1 5 D S 2 9 A 4 4 0
C 6 D 1 5 D S 2 9 B 1 3 9
C 6 D 1 5 D S 2 9 B 3 2 - 1 4 3 7 2 7 3 - 7 3 9
C 6 D 1 5 D S 2 9 B 4 4 0
C 6 D 1 5 D S 2 9 C 1 2 - 1 4 3 7 2 7 3 - 8 3 9
C 6 D 1 5 D S 2 9 C 3 2 - 1 4 3 7 2 7 3 - 9 3 9
C 6 D 1 5 D S 2 9 C 4 4 0
C 6 D 1 5 D S 2 9 D 1 3 - 1 4 3 7 2 7 3 - 0 3 9
C 6 D 1 5 D S 2 9 D 3 3 - 1 4 3 7 2 7 3 - 1 3 9
C 6 D 1 5 D S 2 9 D 4 4 0
C 6 D 1 5 D S 2 9 E 1 3 9
C 6 D 1 5 D S 2 9 E 3 3 9
C 6 D 1 5 D S 2 9 E 4 4 0
C 6 D 1 5 P F 2 9 0 1 2 1 4 8
C 6 D 1 5 P F 2 9 0 1 3 1 4 8
C 6 D 1 5 P F 2 9 0 2 2 0 - 1 4 3 7 2 6 2 - 9 1 4 6
C 6 D 1 5 P F 2 9 0 2 3 1 - 1 4 3 7 2 6 2 - 0 1 4 6
C 6 D 1 5 P F 2 9 0 3 2 1 4 6
C 6 D 1 5 P F 2 9 0 3 3 1 4 6
C 6 D 1 5 P F 2 9 0 4 2 1 4 8
C 6 D 1 5 P F 2 9 0 4 3 1 4 8
C 6 D 1 5 P F 2 9 1 3 2 1 4 8
C 6 D 1 5 P F 2 9 1 3 3 1 4 8
C 6 D 1 5 P F 2 9 1 4 2 1 4 6
C 6 D 1 5 P F 2 9 1 4 3 1 4 6
C 6 D 1 8 D S 2 9 A 1 3 - 1 4 3 7 2 7 3 - 2 3 9
C 6 D 1 8 D S 2 9 A 3 3 - 1 4 3 7 2 7 3 - 3 3 9
C 6 D 1 8 D S 2 9 A 4 4 0
C 6 D 1 8 D S 2 9 B 1 3 9
C 6 D 1 8 D S 2 9 B 3 3 9
C 6 D 1 8 D S 2 9 B 4 4 0
C 6 D 1 8 D S 2 9 C 1 3 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 1 8 D S 2 9 C 3 3 9
C 6 D 1 8 D S 2 9 C 4 4 0
C 6 D 1 8 D S 2 9 D 1 3 9
C 6 D 1 8 D S 2 9 D 3 3 9
C 6 D 1 8 D S 2 9 D 4 4 0
C 6 D 1 8 D S 2 9 E 1 3 9
C 6 D 1 8 D S 2 9 E 3 3 9
C 6 D 1 8 D S 2 9 E 4 4 0
C 6 D 1 8 P F 2 9 0 1 2 1 4 8
C 6 D 1 8 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 2 - 3 1 4 8
C 6 D 1 8 P F 2 9 0 2 2 1 4 6
C 6 D 1 8 P F 2 9 0 2 3 1 - 1 4 3 7 2 6 2 - 4 1 4 6
C 6 D 1 8 P F 2 9 0 3 2 1 4 6
C 6 D 1 8 P F 2 9 0 3 3 1 4 6
C 6 D 1 8 P F 2 9 0 4 2 1 4 8
C 6 D 1 8 P F 2 9 0 4 3 1 4 8
C 6 D 1 8 P F 2 9 1 3 2 1 4 8
C 6 D 1 8 P F 2 9 1 3 3 1 4 8
C 6 D 1 8 P F 2 9 1 4 2 1 4 6
C 6 D 1 8 P F 2 9 1 4 3 1 4 6
C 6 D 2 0 D S 2 9 A 1 3 9
C 6 D 2 0 D S 2 9 A 3 3 9
C 6 D 2 0 D S 2 9 A 4 4 0
C 6 D 2 0 D S 2 9 B 1 3 9
C 6 D 2 0 D S 2 9 B 3 3 9
C 6 D 2 0 D S 2 9 B 4 4 0
C 6 D 2 0 D S 2 9 C 1 3 9
C 6 D 2 0 D S 2 9 C 3 3 9
C 6 D 2 0 D S 2 9 C 4 4 0
C 6 D 2 0 D S 2 9 D 1 3 9
C 6 D 2 0 D S 2 9 D 3 3 9
C 6 D 2 0 D S 2 9 D 4 4 0
C 6 D 2 0 D S 2 9 E 1 3 9
C 6 D 2 0 D S 2 9 E 3 3 9
C 6 D 2 0 D S 2 9 E 4 4 0
C 6 D 2 0 P F 2 9 0 1 2 1 4 8
C 6 D 2 0 P F 2 9 0 1 3 1 4 8
C 6 D 2 0 P F 2 9 0 2 2 1 4 6
C 6 D 2 0 P F 2 9 0 2 3 1 4 6
C 6 D 2 0 P F 2 9 0 3 2 1 4 6
C 6 D 2 0 P F 2 9 0 3 3 1 4 6
C 6 D 2 0 P F 2 9 0 4 2 1 4 8
C 6 D 2 0 P F 2 9 0 4 3 1 4 8
C 6 D 2 0 P F 2 9 1 3 2 1 4 8
C 6 D 2 0 P F 2 9 1 3 3 1 4 8
C 6 D 2 0 P F 2 9 1 4 2 1 4 6
C 6 D 2 0 P F 2 9 1 4 3 1 4 6
C 6 D 2 2 D S 2 9 A 1 3 - 1 4 3 7 2 7 3 - 5 3 9
C 6 D 2 2 D S 2 9 A 3 3 - 1 4 3 7 2 7 3 - 6 3 9
C 6 D 2 2 D S 2 9 A 4 4 0
C 6 D 2 2 D S 2 9 B 1 3 9
C 6 D 2 2 D S 2 9 B 3 3 9
C 6 D 2 2 D S 2 9 B 4 3 - 1 4 3 7 2 7 3 - 7 4 0
C 6 D 2 2 D S 2 9 C 1 3 - 1 4 3 7 2 7 3 - 8 3 9
C 6 D 2 2 D S 2 9 C 3 3 9
C 6 D 2 2 D S 2 9 C 4 4 0
C 6 D 2 2 D S 2 9 D 1 3 - 1 4 3 7 2 7 3 - 9 3 9
C 6 D 2 2 D S 2 9 D 3 4 - 1 4 3 7 2 7 3 - 0 3 9
C 6 D 2 2 D S 2 9 D 4 4 0
C 6 D 2 2 D S 2 9 E 1 3 9
C 6 D 2 2 D S 2 9 E 3 3 9
C 6 D 2 2 D S 2 9 E 4 4 0
C 6 D 2 2 P F 2 9 0 1 2 1 4 8
C 6 D 2 2 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 2 - 8 1 4 8
C 6 D 2 2 P F 2 9 0 2 2 1 4 6
C 6 D 2 2 P F 2 9 0 2 3 1 - 1 4 3 7 2 6 2 - 9 1 4 6
C 6 D 2 2 P F 2 9 0 3 2 1 4 6
C 6 D 2 2 P F 2 9 0 3 3 1 4 6
C 6 D 2 2 P F 2 9 0 4 2 1 4 8
C 6 D 2 2 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 2 - 0 1 4 8
C 6 D 2 2 P F 2 9 1 3 2 1 4 8
C 6 D 2 2 P F 2 9 1 3 3 1 4 8
C 6 D 2 2 P F 2 9 1 4 2 1 4 6
C 6 D 2 2 P F 2 9 1 4 3 1 4 6
C 6 D 2 5 D S 2 9 A 1 3 9
C 6 D 2 5 D S 2 9 A 3 4 - 1 4 3 7 2 7 3 - 1 3 9
C 6 D 2 5 D S 2 9 A 4 4 0
C 6 D 2 5 D S 2 9 B 1 3 9
C 6 D 2 5 D S 2 9 B 3 3 9
C 6 D 2 5 D S 2 9 B 4 4 0
C 6 D 2 5 D S 2 9 C 1 3 9
C 6 D 2 5 D S 2 9 C 3 4 - 1 4 3 7 2 7 3 - 2 3 9
C 6 D 2 5 D S 2 9 C 4 4 0
C 6 D 2 5 D S 2 9 D 1 4 - 1 4 3 7 2 7 3 - 3 3 9
C 6 D 2 5 D S 2 9 D 3 3 9
C 6 D 2 5 D S 2 9 D 4 4 0
C 6 D 2 5 D S 2 9 E 1 3 9
C 6 D 2 5 D S 2 9 E 3 3 9
C 6 D 2 5 D S 2 9 E 4 4 0
C 6 D 2 5 P F 2 9 0 1 2 1 4 8
C 6 D 2 5 P F 2 9 0 1 3 1 4 8
C 6 D 2 5 P F 2 9 0 2 2 1 4 6
C 6 D 2 5 P F 2 9 0 2 3 1 4 6
C 6 D 2 5 P F 2 9 0 3 2 1 4 6
C 6 D 2 5 P F 2 9 0 3 3 1 4 6
C 6 D 2 5 P F 2 9 0 4 2 1 4 8
C 6 D 2 5 P F 2 9 0 4 3 1 4 8
C 6 D 2 5 P F 2 9 1 3 2 1 4 8
C 6 D 2 5 P F 2 9 1 3 3 1 4 8
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
197
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 6 D 2 5 P F 2 9 1 4 2 1 4 6
C 6 D 2 5 P F 2 9 1 4 3 1 4 6
C 6 D 2 8 D S 2 9 A 1 3 9
C 6 D 2 8 D S 2 9 A 3 3 9
C 6 D 2 8 D S 2 9 A 4 4 0
C 6 D 2 8 D S 2 9 B 1 3 9
C 6 D 2 8 D S 2 9 B 3 3 9
C 6 D 2 8 D S 2 9 B 4 4 0
C 6 D 2 8 D S 2 9 C 1 4 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 2 8 D S 2 9 C 3 4 - 1 4 3 7 2 7 3 - 6 3 9
C 6 D 2 8 D S 2 9 C 4 4 0
C 6 D 2 8 D S 2 9 D 1 4 - 1 4 3 7 2 7 3 - 7 3 9
C 6 D 2 8 D S 2 9 D 3 3 9
C 6 D 2 8 D S 2 9 D 4 4 0
C 6 D 2 8 D S 2 9 E 1 3 9
C 6 D 2 8 D S 2 9 E 3 3 9
C 6 D 2 8 D S 2 9 E 4 4 0
C 6 D 2 8 P F 2 9 0 1 2 1 4 8
C 6 D 2 8 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 2 - 4 1 4 8
C 6 D 2 8 P F 2 9 0 2 2 1 4 6
C 6 D 2 8 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 2 - 6 1 4 6
C 6 D 2 8 P F 2 9 0 3 2 1 4 6
C 6 D 2 8 P F 2 9 0 3 3 2 - 1 4 3 7 2 6 2 - 7 1 4 6
C 6 D 2 8 P F 2 9 0 4 2 1 4 8
C 6 D 2 8 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 2 - 8 1 4 8
C 6 D 2 8 P F 2 9 1 3 2 1 4 8
C 6 D 2 8 P F 2 9 1 3 3 1 4 8
C 6 D 2 8 P F 2 9 1 4 2 1 4 6
C 6 D 2 8 P F 2 9 1 4 3 1 4 6
C 6 D 3 0 D S 2 9 A 1 3 9
C 6 D 3 0 D S 2 9 A 3 3 9
C 6 D 3 0 D S 2 9 A 4 4 0
C 6 D 3 0 D S 2 9 B 1 3 9
C 6 D 3 0 D S 2 9 B 3 3 9
C 6 D 3 0 D S 2 9 B 4 4 0
C 6 D 3 0 D S 2 9 C 1 4 - 1 4 3 7 2 7 3 - 8 3 9
C 6 D 3 0 D S 2 9 C 3 4 - 1 4 3 7 2 7 3 - 9 3 9
C 6 D 3 0 D S 2 9 C 4 4 0
C 6 D 3 0 D S 2 9 D 1 3 9
C 6 D 3 0 D S 2 9 D 3 5 - 1 4 3 7 2 7 3 - 0 3 9
C 6 D 3 0 D S 2 9 D 4 5 - 1 4 3 7 2 7 3 - 1 4 0
C 6 D 3 0 D S 2 9 E 1 3 9
C 6 D 3 0 D S 2 9 E 3 3 9
C 6 D 3 0 D S 2 9 E 4 4 0
C 6 D 3 0 P F 2 9 0 1 2 1 4 8
C 6 D 3 0 P F 2 9 0 1 3 1 4 8
C 6 D 3 0 P F 2 9 0 2 2 1 4 6
C 6 D 3 0 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 2 - 9 1 4 6
C 6 D 3 0 P F 2 9 0 3 2 1 4 6
C 6 D 3 0 P F 2 9 0 3 3 1 4 6
C 6 D 3 0 P F 2 9 0 4 2 1 4 8
C 6 D 3 0 P F 2 9 0 4 3 1 4 8
C 6 D 3 0 P F 2 9 1 3 2 1 4 8
C 6 D 3 0 P F 2 9 1 3 3 1 4 8
C 6 D 3 0 P F 2 9 1 4 2 1 4 6
C 6 D 3 0 P F 2 9 1 4 3 1 4 6
C 6 D 3 1 D S 2 9 A 1 5 - 1 4 3 7 2 7 3 - 2 3 9
C 6 D 3 1 D S 2 9 A 3 3 9
C 6 D 3 1 D S 2 9 A 4 4 0
C 6 D 3 1 D S 2 9 B 1 3 9
C 6 D 3 1 D S 2 9 B 3 3 9
C 6 D 3 1 D S 2 9 B 4 4 0
C 6 D 3 1 D S 2 9 C 1 3 9
C 6 D 3 1 D S 2 9 C 3 3 9
C 6 D 3 1 D S 2 9 C 4 4 0
C 6 D 3 1 D S 2 9 D 1 3 9
C 6 D 3 1 D S 2 9 D 3 3 9
C 6 D 3 1 D S 2 9 D 4 4 0
C 6 D 3 1 D S 2 9 E 1 3 9
C 6 D 3 1 D S 2 9 E 3 3 9
C 6 D 3 1 D S 2 9 E 4 4 0
C 6 D 3 1 P F 2 9 0 1 2 1 4 8
C 6 D 3 1 P F 2 9 0 1 3 1 4 8
C 6 D 3 1 P F 2 9 0 2 2 1 4 6
C 6 D 3 1 P F 2 9 0 2 3 1 4 6
C 6 D 3 1 P F 2 9 0 3 2 1 4 6
C 6 D 3 1 P F 2 9 0 3 3 1 4 6
C 6 D 3 1 P F 2 9 0 4 2 1 4 8
C 6 D 3 1 P F 2 9 0 4 3 1 4 8
C 6 D 3 1 P F 2 9 1 3 2 1 4 8
C 6 D 3 1 P F 2 9 1 3 3 1 4 8
C 6 D 3 1 P F 2 9 1 4 2 1 4 6
C 6 D 3 1 P F 2 9 1 4 3 1 4 6
C 6 D 3 5 D S 2 9 A 1 3 9
C 6 D 3 5 D S 2 9 A 3 3 9
C 6 D 3 5 D S 2 9 A 4 4 0
C 6 D 3 5 D S 2 9 B 1 3 9
C 6 D 3 5 D S 2 9 B 3 3 9
C 6 D 3 5 D S 2 9 B 4 4 0
C 6 D 3 5 D S 2 9 C 1 3 9
C 6 D 3 5 D S 2 9 C 3 3 9
C 6 D 3 5 D S 2 9 C 4 4 0
C 6 D 3 5 D S 2 9 D 1 3 9
C 6 D 3 5 D S 2 9 D 3 3 9
C 6 D 3 5 D S 2 9 D 4 4 0
C 6 D 3 5 D S 2 9 E 1 3 9
C 6 D 3 5 D S 2 9 E 3 3 9
C 6 D 3 5 D S 2 9 E 4 4 0
C 6 D 3 5 P F 2 9 0 1 2 1 4 8
C 6 D 3 5 P F 2 9 0 1 3 1 4 8
C 6 D 3 5 P F 2 9 0 2 2 1 4 6
C 6 D 3 5 P F 2 9 0 2 3 1 4 6
C 6 D 3 5 P F 2 9 0 3 2 1 4 6
C 6 D 3 5 P F 2 9 0 3 3 1 4 6
C 6 D 3 5 P F 2 9 0 4 2 1 4 8
C 6 D 3 5 P F 2 9 0 4 3 1 4 8
C 6 D 3 5 P F 2 9 1 3 2 1 4 8
C 6 D 3 5 P F 2 9 1 3 3 1 4 8
C 6 D 3 5 P F 2 9 1 4 2 1 4 6
C 6 D 3 5 P F 2 9 1 4 3 1 4 6
C 6 D 3 6 D S 2 9 A 1 3 9
C 6 D 3 6 D S 2 9 A 3 5 - 1 4 3 7 2 7 3 - 3 3 9
C 6 D 3 6 D S 2 9 A 4 4 0
C 6 D 3 6 D S 2 9 B 1 3 9
C 6 D 3 6 D S 2 9 B 3 3 9
C 6 D 3 6 D S 2 9 B 4 4 0
C 6 D 3 6 D S 2 9 C 1 5 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 3 6 D S 2 9 C 3 3 - 1 4 3 7 2 6 4 - 3 3 9
C 6 D 3 6 D S 2 9 C 4 4 0
C 6 D 3 6 D S 2 9 D 1 5 - 1 4 3 7 2 7 3 - 5 3 9
C 6 D 3 6 D S 2 9 D 3 3 9
C 6 D 3 6 D S 2 9 D 4 5 - 1 4 3 7 2 7 3 - 6 4 0
C 6 D 3 6 D S 2 9 E 1 3 9
C 6 D 3 6 D S 2 9 E 3 3 9
C 6 D 3 6 D S 2 9 E 4 5 - 1 4 3 7 2 7 3 - 7 4 0
C 6 D 3 6 P F 2 9 0 1 2 1 4 8
C 6 D 3 6 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 2 - 3 1 4 8
C 6 D 3 6 P F 2 9 0 2 2 1 4 6
C 6 D 3 6 P F 2 9 0 2 3 3 - 1 4 3 7 2 6 2 - 4 1 4 6
C 6 D 3 6 P F 2 9 0 3 2 1 4 6
C 6 D 3 6 P F 2 9 0 3 3 1 4 6
C 6 D 3 6 P F 2 9 0 4 2 1 4 8
C 6 D 3 6 P F 2 9 0 4 3 1 4 8
C 6 D 3 6 P F 2 9 1 3 2 1 4 8
C 6 D 3 6 P F 2 9 1 3 3 1 4 8
C 6 D 3 6 P F 2 9 1 4 2 1 4 6
C 6 D 3 6 P F 2 9 1 4 3 1 4 6
C 6 D 4 0 D S 2 9 A 1 3 9
C 6 D 4 0 D S 2 9 A 3 3 9
C 6 D 4 0 D S 2 9 A 4 4 0
C 6 D 4 0 D S 2 9 B 1 3 9
C 6 D 4 0 D S 2 9 B 3 5 - 1 4 3 7 2 7 3 - 8 3 9
C 6 D 4 0 D S 2 9 B 4 4 0
C 6 D 4 0 D S 2 9 C 1 3 9
C 6 D 4 0 D S 2 9 C 3 3 9
C 6 D 4 0 D S 2 9 C 4 4 0
C 6 D 4 0 D S 2 9 D 1 3 9
C 6 D 4 0 D S 2 9 D 3 3 9
C 6 D 4 0 D S 2 9 D 4 4 0
C 6 D 4 0 D S 2 9 E 1 3 9
C 6 D 4 0 D S 2 9 E 3 3 9
C 6 D 4 0 D S 2 9 E 4 4 0
C 6 D 4 0 P F 2 9 0 1 2 1 4 8
C 6 D 4 0 P F 2 9 0 1 3 1 4 8
C 6 D 4 0 P F 2 9 0 2 2 1 4 6
C 6 D 4 0 P F 2 9 0 2 3 1 4 6
C 6 D 4 0 P F 2 9 0 3 2 1 4 6
C 6 D 4 0 P F 2 9 0 3 3 1 4 6
C 6 D 4 0 P F 2 9 0 4 2 1 4 8
C 6 D 4 0 P F 2 9 0 4 3 1 4 8
C 6 D 4 0 P F 2 9 1 3 2 1 4 8
C 6 D 4 0 P F 2 9 1 3 3 1 4 8
C 6 D 4 0 P F 2 9 1 4 2 1 4 6
C 6 D 4 0 P F 2 9 1 4 3 1 4 6
C 6 D 4 3 D S 2 9 A 1 5 - 1 4 3 7 2 7 3 - 9 3 9
C 6 D 4 3 D S 2 9 A 3 3 9
C 6 D 4 3 D S 2 9 A 4 6 - 1 4 3 7 2 7 3 - 0 4 0
C 6 D 4 3 D S 2 9 B 1 6 - 1 4 3 7 2 7 3 - 1 3 9
C 6 D 4 3 D S 2 9 B 3 3 9
C 6 D 4 3 D S 2 9 B 4 4 0
C 6 D 4 3 D S 2 9 C 1 6 - 1 4 3 7 2 7 3 - 2 3 9
C 6 D 4 3 D S 2 9 C 3 6 - 1 4 3 7 2 7 3 - 4 3 9
C 6 D 4 3 D S 2 9 C 4 4 0
C 6 D 4 3 D S 2 9 D 1 3 9
C 6 D 4 3 D S 2 9 D 3 6 - 1 4 3 7 2 7 3 - 6 3 9
C 6 D 4 3 D S 2 9 D 4 4 0
C 6 D 4 3 D S 2 9 E 1 3 9
C 6 D 4 3 D S 2 9 E 3 3 9
C 6 D 4 3 D S 2 9 E 4 4 0
C 6 D 4 3 P F 2 9 0 1 2 1 4 8
C 6 D 4 3 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 2 - 6 1 4 8
C 6 D 4 3 P F 2 9 0 2 2 3 - 1 4 3 7 2 6 2 - 8 1 4 6
C 6 D 4 3 P F 2 9 0 2 3 3 - 1 4 3 7 2 6 2 - 9 1 4 6
C 6 D 4 3 P F 2 9 0 3 2 1 4 6
C 6 D 4 3 P F 2 9 0 3 3 1 4 6
C 6 D 4 3 P F 2 9 0 4 2 1 4 8
C 6 D 4 3 P F 2 9 0 4 3 4 - 1 4 3 7 2 6 2 - 0 1 4 8
C 6 D 4 3 P F 2 9 1 3 2 1 4 8
C 6 D 4 3 P F 2 9 1 3 3 1 4 8
C 6 D 4 3 P F 2 9 1 4 2 1 4 6
C 6 D 4 3 P F 2 9 1 4 3 1 4 6
C 6 D 5 0 D S 2 9 A 1 3 9
C 6 D 5 0 D S 2 9 A 3 3 9
C 6 D 5 0 D S 2 9 A 4 4 0
C 6 D 5 0 D S 2 9 B 1 3 9
C 6 D 5 0 D S 2 9 B 3 3 9
C 6 D 5 0 D S 2 9 B 4 4 0
C 6 D 5 0 D S 2 9 C 1 3 9
C 6 D 5 0 D S 2 9 C 3 3 9
C 6 D 5 0 D S 2 9 C 4 4 0
C 6 D 5 0 D S 2 9 D 1 3 9
C 6 D 5 0 D S 2 9 D 3 3 9
C 6 D 5 0 D S 2 9 D 4 4 0
C 6 D 5 0 D S 2 9 E 1 3 9
C 6 D 5 0 D S 2 9 E 3 3 9
C 6 D 5 0 D S 2 9 E 4 4 0
C 7 D 0 6 D S 2 9 A 1 3 6
C 7 D 0 6 D S 2 9 A 3 3 6
C 7 D 0 6 D S 2 9 A 4 3 7
C 7 D 0 6 D S 2 9 B 1 3 6
C 7 D 0 6 D S 2 9 B 3 3 6
C 7 D 0 6 D S 2 9 B 4 3 7
C 7 D 0 6 D S 2 9 C 1 0 - 1 4 3 7 2 7 4 - 3 3 6
C 7 D 0 6 D S 2 9 C 3 3 6
C 7 D 0 6 D S 2 9 C 4 3 7
C 7 D 0 6 D S 2 9 D 1 3 6
C 7 D 0 6 D S 2 9 D 3 3 6
C 7 D 0 6 D S 2 9 D 4 3 7
C 7 D 0 6 D S 2 9 E 1 3 6
C 7 D 0 6 D S 2 9 E 3 3 6
C 7 D 0 6 D S 2 9 E 4 3 7
C 7 D 0 6 P F 2 9 0 1 2 1 4 4
C 7 D 0 6 P F 2 9 0 1 3 1 4 4
C 7 D 0 6 P F 2 9 0 2 2 1 4 2
C 7 D 0 6 P F 2 9 0 2 3 0 - 1 4 3 7 2 6 3 - 7 1 4 2
C 7 D 0 6 P F 2 9 0 3 2 1 4 2
C 7 D 0 6 P F 2 9 0 3 3 1 4 2
C 7 D 0 6 P F 2 9 0 4 2 1 4 4
C 7 D 0 6 P F 2 9 0 4 3 0 - 1 4 3 7 2 6 3 - 8 1 4 4
C 7 D 0 6 P F 2 9 1 3 2 1 4 4
C 7 D 0 6 P F 2 9 1 3 3 1 4 4
C 7 D 0 6 P F 2 9 1 4 2 1 4 2
C 7 D 0 6 P F 2 9 1 4 3 1 4 2
C 7 D 1 0 D S 2 9 A 1 3 6
C 7 D 1 0 D S 2 9 A 3 3 6
C 7 D 1 0 D S 2 9 A 4 3 7
C 7 D 1 0 D S 2 9 B 1 3 6
C 7 D 1 0 D S 2 9 B 3 3 6
C 7 D 1 0 D S 2 9 B 4 3 7
C 7 D 1 0 D S 2 9 C 1 3 6
C 7 D 1 0 D S 2 9 C 3 3 6
C 7 D 1 0 D S 2 9 C 4 3 7
C 7 D 1 0 D S 2 9 D 1 3 6
C 7 D 1 0 D S 2 9 D 3 3 6
C 7 D 1 0 D S 2 9 D 4 3 7
C 7 D 1 0 D S 2 9 E 1 3 6
C 7 D 1 0 D S 2 9 E 3 3 6
C 7 D 1 0 D S 2 9 E 4 3 7
C 7 D 1 0 P F 2 9 0 1 2 1 4 4
C 7 D 1 0 P F 2 9 0 1 3 1 4 4
C 7 D 1 0 P F 2 9 0 2 2 1 4 2
C 7 D 1 0 P F 2 9 0 2 3 1 4 2
C 7 D 1 0 P F 2 9 0 3 2 1 4 2
C 7 D 1 0 P F 2 9 0 3 3 1 4 2
C 7 D 1 0 P F 2 9 0 4 2 1 4 4
C 7 D 1 0 P F 2 9 0 4 3 1 4 4
C 7 D 1 0 P F 2 9 1 3 2 1 4 4
C 7 D 1 0 P F 2 9 1 3 3 1 4 4
C 7 D 1 0 P F 2 9 1 4 2 1 4 2
C 7 D 1 0 P F 2 9 1 4 3 1 4 2
C 7 D 1 2 P F 2 9 0 1 2 1 4 4
C 7 D 1 2 P F 2 9 0 1 3 1 4 4
C 7 D 1 2 P F 2 9 0 2 2 1 4 2
C 7 D 1 2 P F 2 9 0 2 3 1 4 2
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
198
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 7 D 1 2 P F 2 9 0 3 2 1 4 2
C 7 D 1 2 P F 2 9 0 3 3 1 4 2
C 7 D 1 2 P F 2 9 0 4 2 1 4 4
C 7 D 1 2 P F 2 9 0 4 3 1 4 4
C 7 D 1 2 P F 2 9 1 3 2 1 4 4
C 7 D 1 2 P F 2 9 1 3 3 1 4 4
C 7 D 1 2 P F 2 9 1 4 2 1 4 2
C 7 D 1 2 P F 2 9 1 4 3 1 4 2
C 7 D 1 5 D S 2 9 A 1 3 6
C 7 D 1 5 D S 2 9 A 3 3 6
C 7 D 1 5 D S 2 9 A 4 3 7
C 7 D 1 5 D S 2 9 B 1 3 6
C 7 D 1 5 D S 2 9 B 3 3 6
C 7 D 1 5 D S 2 9 B 4 3 7
C 7 D 1 5 D S 2 9 C 1 0 - 1 4 3 7 2 7 4 - 5 3 6
C 7 D 1 5 D S 2 9 C 3 0 - 1 4 3 7 2 7 4 - 7 3 6
C 7 D 1 5 D S 2 9 C 4 3 7
C 7 D 1 5 D S 2 9 D 1 3 6
C 7 D 1 5 D S 2 9 D 3 3 6
C 7 D 1 5 D S 2 9 D 4 3 7
C 7 D 1 5 D S 2 9 E 1 3 6
C 7 D 1 5 D S 2 9 E 3 3 6
C 7 D 1 5 D S 2 9 E 4 3 7
C 7 D 1 5 P F 2 9 0 1 2 1 4 4
C 7 D 1 5 P F 2 9 0 1 3 1 4 4
C 7 D 1 5 P F 2 9 0 2 2 1 4 2
C 7 D 1 5 P F 2 9 0 2 3 1 4 2
C 7 D 1 5 P F 2 9 0 3 2 1 4 2
C 7 D 1 5 P F 2 9 0 3 3 1 4 2
C 7 D 1 5 P F 2 9 0 4 2 1 4 4
C 7 D 1 5 P F 2 9 0 4 3 1 4 4
C 7 D 1 5 P F 2 9 1 3 2 1 4 4
C 7 D 1 5 P F 2 9 1 3 3 1 4 4
C 7 D 1 5 P F 2 9 1 4 2 1 4 2
C 7 D 1 5 P F 2 9 1 4 3 1 4 2
C 7 D 1 8 D S 2 9 A 1 3 6
C 7 D 1 8 D S 2 9 A 3 3 6
C 7 D 1 8 D S 2 9 A 4 3 7
C 7 D 1 8 D S 2 9 B 1 3 6
C 7 D 1 8 D S 2 9 B 3 3 6
C 7 D 1 8 D S 2 9 B 4 3 7
C 7 D 1 8 D S 2 9 C 1 3 6
C 7 D 1 8 D S 2 9 C 3 0 - 1 4 3 7 2 7 4 - 8 3 6
C 7 D 1 8 D S 2 9 C 4 3 7
C 7 D 1 8 D S 2 9 D 1 3 6
C 7 D 1 8 D S 2 9 D 3 3 6
C 7 D 1 8 D S 2 9 D 4 3 7
C 7 D 1 8 D S 2 9 E 1 3 6
C 7 D 1 8 D S 2 9 E 3 3 6
C 7 D 1 8 D S 2 9 E 4 3 7
C 7 D 1 8 P F 2 9 0 1 2 1 - 1 4 3 7 2 6 3 - 4 1 4 4
C 7 D 1 8 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 3 - 5 1 4 4
C 7 D 1 8 P F 2 9 0 2 2 1 - 1 4 3 7 2 6 3 - 6 1 4 2
C 7 D 1 8 P F 2 9 0 2 3 1 - 1 4 3 7 2 6 3 - 7 1 4 2
C 7 D 1 8 P F 2 9 0 3 2 1 4 2
C 7 D 1 8 P F 2 9 0 3 3 1 4 2
C 7 D 1 8 P F 2 9 0 4 2 1 4 4
C 7 D 1 8 P F 2 9 0 4 3 1 - 1 4 3 7 2 6 3 - 8 1 4 4
C 7 D 1 8 P F 2 9 1 3 2 1 4 4
C 7 D 1 8 P F 2 9 1 3 3 1 4 4
C 7 D 1 8 P F 2 9 1 4 2 1 4 2
C 7 D 1 8 P F 2 9 1 4 3 1 4 2
C 7 D 2 0 P F 2 9 0 1 2 1 - 1 4 3 7 2 6 3 - 9 1 4 4
C 7 D 2 0 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 3 - 0 1 4 4
C 7 D 2 0 P F 2 9 0 2 2 1 4 2
C 7 D 2 0 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 3 - 1 1 4 2
C 7 D 2 0 P F 2 9 0 3 2 1 4 2
C 7 D 2 0 P F 2 9 0 3 3 1 4 2
C 7 D 2 0 P F 2 9 0 4 2 1 4 4
C 7 D 2 0 P F 2 9 0 4 3 1 4 4
C 7 D 2 0 P F 2 9 1 3 2 1 4 4
C 7 D 2 0 P F 2 9 1 3 3 1 4 4
C 7 D 2 0 P F 2 9 1 4 2 1 4 2
C 7 D 2 0 P F 2 9 1 4 3 1 4 2
C 7 D 2 2 D S 2 9 A 1 3 6
C 7 D 2 2 D S 2 9 A 3 3 6
C 7 D 2 2 D S 2 9 A 4 3 7
C 7 D 2 2 D S 2 9 B 1 3 6
C 7 D 2 2 D S 2 9 B 3 3 6
C 7 D 2 2 D S 2 9 B 4 3 7
C 7 D 2 2 D S 2 9 C 1 0 - 1 4 3 7 2 7 4 - 9 3 6
C 7 D 2 2 D S 2 9 C 3 3 6
C 7 D 2 2 D S 2 9 C 4 3 7
C 7 D 2 2 D S 2 9 D 1 3 6
C 7 D 2 2 D S 2 9 D 3 1 - 1 4 3 7 2 7 4 - 0 3 6
C 7 D 2 2 D S 2 9 D 4 3 7
C 7 D 2 2 D S 2 9 E 1 3 6
C 7 D 2 2 D S 2 9 E 3 3 6
C 7 D 2 2 D S 2 9 E 4 3 7
C 7 D 2 2 P F 2 9 0 1 2 1 4 4
C 7 D 2 2 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 3 - 3 1 4 4
C 7 D 2 2 P F 2 9 0 2 2 1 4 2
C 7 D 2 2 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 3 - 4 1 4 2
C 7 D 2 2 P F 2 9 0 3 2 1 4 2
C 7 D 2 2 P F 2 9 0 3 3 1 4 2
C 7 D 2 2 P F 2 9 0 4 2 1 4 4
C 7 D 2 2 P F 2 9 0 4 3 1 4 4
C 7 D 2 2 P F 2 9 1 3 2 1 4 4
C 7 D 2 2 P F 2 9 1 3 3 1 4 4
C 7 D 2 2 P F 2 9 1 4 2 1 4 2
C 7 D 2 2 P F 2 9 1 4 3 1 4 2
C 7 D 2 5 D S 2 9 A 1 3 6
C 7 D 2 5 D S 2 9 A 3 3 6
C 7 D 2 5 D S 2 9 A 4 3 7
C 7 D 2 5 D S 2 9 B 1 3 6
C 7 D 2 5 D S 2 9 B 3 3 6
C 7 D 2 5 D S 2 9 B 4 3 7
C 7 D 2 5 D S 2 9 C 1 1 - 1 4 3 7 2 7 4 - 1 3 6
C 7 D 2 5 D S 2 9 C 3 3 6
C 7 D 2 5 D S 2 9 C 4 3 7
C 7 D 2 5 D S 2 9 D 1 3 6
C 7 D 2 5 D S 2 9 D 3 3 6
C 7 D 2 5 D S 2 9 D 4 3 7
C 7 D 2 5 D S 2 9 E 1 3 6
C 7 D 2 5 D S 2 9 E 3 3 6
C 7 D 2 5 D S 2 9 E 4 3 7
C 7 D 2 5 P F 2 9 0 1 2 1 4 4
C 7 D 2 5 P F 2 9 0 1 3 1 4 4
C 7 D 2 5 P F 2 9 0 2 2 1 4 2
C 7 D 2 5 P F 2 9 0 2 3 1 4 2
C 7 D 2 5 P F 2 9 0 3 2 1 4 2
C 7 D 2 5 P F 2 9 0 3 3 1 4 2
C 7 D 2 5 P F 2 9 0 4 2 1 4 4
C 7 D 2 5 P F 2 9 0 4 3 1 4 4
C 7 D 2 5 P F 2 9 1 3 2 1 4 4
C 7 D 2 5 P F 2 9 1 3 3 1 4 4
C 7 D 2 5 P F 2 9 1 4 2 1 4 2
C 7 D 2 5 P F 2 9 1 4 3 1 4 2
C 7 D 2 8 D S 2 9 A 1 1 - 1 4 3 7 2 7 4 - 3 3 6
C 7 D 2 8 D S 2 9 A 3 1 - 1 4 3 7 2 7 4 - 4 3 6
C 7 D 2 8 D S 2 9 A 4 3 7
C 7 D 2 8 D S 2 9 B 1 3 6
C 7 D 2 8 D S 2 9 B 3 1 - 1 4 3 7 2 7 4 - 6 3 6
C 7 D 2 8 D S 2 9 B 4 3 7
C 7 D 2 8 D S 2 9 C 1 1 - 1 4 3 7 2 7 4 - 7 3 6
C 7 D 2 8 D S 2 9 C 3 1 - 1 4 3 7 2 7 4 - 8 3 6
C 7 D 2 8 D S 2 9 C 4 3 7
C 7 D 2 8 D S 2 9 D 1 1 - 1 4 3 7 2 7 4 - 9 3 6
C 7 D 2 8 D S 2 9 D 3 2 - 1 4 3 7 2 7 4 - 0 3 6
C 7 D 2 8 D S 2 9 D 4 3 7
C 7 D 2 8 D S 2 9 E 1 3 6
C 7 D 2 8 D S 2 9 E 3 2 - 1 4 3 7 2 7 4 - 2 3 6
C 7 D 2 8 D S 2 9 E 4 3 7
C 7 D 2 8 P F 2 9 0 1 2 2 - 1 4 3 7 2 6 3 - 7 1 4 4
C 7 D 2 8 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 3 - 8 1 4 4
C 7 D 2 8 P F 2 9 0 2 2 1 4 2
C 7 D 2 8 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 3 - 9 1 4 2
C 7 D 2 8 P F 2 9 0 3 2 2 - 1 4 3 7 2 7 4 - 3 1 4 2
C 7 D 2 8 P F 2 9 0 3 3 1 4 2
C 7 D 2 8 P F 2 9 0 4 2 1 4 4
C 7 D 2 8 P F 2 9 0 4 3 1 4 4
C 7 D 2 8 P F 2 9 1 3 2 1 4 4
C 7 D 2 8 P F 2 9 1 3 3 1 4 4
C 7 D 2 8 P F 2 9 1 4 2 1 4 2
C 7 D 2 8 P F 2 9 1 4 3 1 4 2
C 7 D 3 0 D S 2 9 A 1 3 6
C 7 D 3 0 D S 2 9 A 3 2 - 1 4 3 7 2 7 4 - 4 3 6
C 7 D 3 0 D S 2 9 A 4 3 7
C 7 D 3 0 D S 2 9 B 1 3 6
C 7 D 3 0 D S 2 9 B 3 3 6
C 7 D 3 0 D S 2 9 B 4 3 7
C 7 D 3 0 D S 2 9 C 1 3 6
C 7 D 3 0 D S 2 9 C 3 2 - 1 4 3 7 2 7 4 - 5 3 6
C 7 D 3 0 D S 2 9 C 4 2 - 1 4 3 7 2 7 4 - 6 3 7
C 7 D 3 0 D S 2 9 D 1 3 6
C 7 D 3 0 D S 2 9 D 3 3 6
C 7 D 3 0 D S 2 9 D 4 3 7
C 7 D 3 0 D S 2 9 E 1 3 6
C 7 D 3 0 D S 2 9 E 3 3 6
C 7 D 3 0 D S 2 9 E 4 3 7
C 7 D 3 0 P F 2 9 0 1 2 1 4 4
C 7 D 3 0 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 3 - 1 1 4 4
C 7 D 3 0 P F 2 9 0 2 2 1 4 2
C 7 D 3 0 P F 2 9 0 2 3 3 - 1 4 3 7 2 6 3 - 2 1 4 2
C 7 D 3 0 P F 2 9 0 3 2 2 - 1 4 3 7 2 7 4 - 7 1 4 2
C 7 D 3 0 P F 2 9 0 3 3 1 4 2
C 7 D 3 0 P F 2 9 0 4 2 1 4 4
C 7 D 3 0 P F 2 9 0 4 3 3 - 1 4 3 7 2 6 3 - 3 1 4 4
C 7 D 3 0 P F 2 9 1 3 2 1 4 4
C 7 D 3 0 P F 2 9 1 3 3 1 4 4
C 7 D 3 0 P F 2 9 1 4 2 1 4 2
C 7 D 3 0 P F 2 9 1 4 3 1 4 2
C 7 D 3 1 D S 2 9 A 1 3 6
C 7 D 3 1 D S 2 9 A 3 2 - 1 4 3 7 2 7 4 - 8 3 6
C 7 D 3 1 D S 2 9 A 4 3 7
C 7 D 3 1 D S 2 9 B 1 3 6
C 7 D 3 1 D S 2 9 B 3 3 6
C 7 D 3 1 D S 2 9 B 4 3 7
C 7 D 3 1 D S 2 9 C 1 3 6
C 7 D 3 1 D S 2 9 C 3 2 - 1 4 3 7 2 7 4 - 9 3 6
C 7 D 3 1 D S 2 9 C 4 3 7
C 7 D 3 1 D S 2 9 D 1 3 6
C 7 D 3 1 D S 2 9 D 3 3 - 1 4 3 7 2 7 4 - 0 3 6
C 7 D 3 1 D S 2 9 D 4 3 7
C 7 D 3 1 D S 2 9 E 1 3 6
C 7 D 3 1 D S 2 9 E 3 3 6
C 7 D 3 1 D S 2 9 E 4 3 7
C 7 D 3 1 P F 2 9 0 1 2 1 4 4
C 7 D 3 1 P F 2 9 0 1 3 1 4 4
C 7 D 3 1 P F 2 9 0 2 2 1 4 2
C 7 D 3 1 P F 2 9 0 2 3 1 4 2
C 7 D 3 1 P F 2 9 0 3 2 1 4 2
C 7 D 3 1 P F 2 9 0 3 3 1 4 2
C 7 D 3 1 P F 2 9 0 4 2 1 4 4
C 7 D 3 1 P F 2 9 0 4 3 1 4 4
C 7 D 3 1 P F 2 9 1 3 2 1 4 4
C 7 D 3 1 P F 2 9 1 3 3 1 4 4
C 7 D 3 1 P F 2 9 1 4 2 1 4 2
C 7 D 3 1 P F 2 9 1 4 3 1 4 2
C 7 D 3 5 D S 2 9 A 1 3 6
C 7 D 3 5 D S 2 9 A 3 3 6
C 7 D 3 5 D S 2 9 A 4 3 7
C 7 D 3 5 D S 2 9 B 1 3 6
C 7 D 3 5 D S 2 9 B 3 3 6
C 7 D 3 5 D S 2 9 B 4 3 7
C 7 D 3 5 D S 2 9 C 1 3 - 1 4 3 7 2 7 4 - 1 3 6
C 7 D 3 5 D S 2 9 C 3 3 6
C 7 D 3 5 D S 2 9 C 4 3 7
C 7 D 3 5 D S 2 9 D 1 3 6
C 7 D 3 5 D S 2 9 D 3 3 6
C 7 D 3 5 D S 2 9 D 4 3 7
C 7 D 3 5 D S 2 9 E 1 3 6
C 7 D 3 5 D S 2 9 E 3 3 6
C 7 D 3 5 D S 2 9 E 4 3 7
C 7 D 3 5 P F 2 9 0 1 2 3 - 1 4 3 7 2 6 3 - 9 1 4 4
C 7 D 3 5 P F 2 9 0 1 3 4 - 1 4 3 7 2 6 3 - 0 1 4 4
C 7 D 3 5 P F 2 9 0 2 2 1 4 2
C 7 D 3 5 P F 2 9 0 2 3 1 4 2
C 7 D 3 5 P F 2 9 0 3 2 1 4 2
C 7 D 3 5 P F 2 9 0 3 3 1 4 2
C 7 D 3 5 P F 2 9 0 4 2 1 4 4
C 7 D 3 5 P F 2 9 0 4 3 1 4 4
C 7 D 3 5 P F 2 9 1 3 2 1 4 4
C 7 D 3 5 P F 2 9 1 3 3 1 4 4
C 7 D 3 5 P F 2 9 1 4 2 1 4 2
C 7 D 3 5 P F 2 9 1 4 3 1 4 2
C 7 D 3 6 D S 2 9 A 1 3 6
C 7 D 3 6 D S 2 9 A 3 3 6
C 7 D 3 6 D S 2 9 A 4 3 7
C 7 D 3 6 D S 2 9 B 1 3 6
C 7 D 3 6 D S 2 9 B 3 3 6
C 7 D 3 6 D S 2 9 B 4 3 7
C 7 D 3 6 D S 2 9 C 1 3 - 1 4 3 7 2 7 4 - 2 3 6
C 7 D 3 6 D S 2 9 C 3 3 - 1 4 3 7 2 7 4 - 3 3 6
C 7 D 3 6 D S 2 9 C 4 3 7
C 7 D 3 6 D S 2 9 D 1 3 6
C 7 D 3 6 D S 2 9 D 3 3 - 1 4 3 7 2 7 4 - 4 3 6
C 7 D 3 6 D S 2 9 D 4 3 7
C 7 D 3 6 D S 2 9 E 1 3 6
C 7 D 3 6 D S 2 9 E 3 3 6
C 7 D 3 6 D S 2 9 E 4 3 7
C 7 D 3 6 P F 2 9 0 1 2 4 - 1 4 3 7 2 6 3 - 1 1 4 4
C 7 D 3 6 P F 2 9 0 1 3 4 - 1 4 3 7 2 6 3 - 2 1 4 4
C 7 D 3 6 P F 2 9 0 2 2 1 4 2
C 7 D 3 6 P F 2 9 0 2 3 1 4 2
C 7 D 3 6 P F 2 9 0 3 2 1 4 2
C 7 D 3 6 P F 2 9 0 3 3 4 - 1 4 3 7 2 6 3 - 3 1 4 2
C 7 D 3 6 P F 2 9 0 4 2 1 4 4
C 7 D 3 6 P F 2 9 0 4 3 1 4 4
C 7 D 3 6 P F 2 9 1 3 2 1 4 4
C 7 D 3 6 P F 2 9 1 3 3 1 4 4
C 7 D 3 6 P F 2 9 1 4 2 1 4 2
C 7 D 3 6 P F 2 9 1 4 3 1 4 2
C 7 D 4 0 D S 2 9 A 1 3 6
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
199
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 7 D 4 0 D S 2 9 A 3 3 6
C 7 D 4 0 D S 2 9 A 4 3 7
C 7 D 4 0 D S 2 9 B 1 3 6
C 7 D 4 0 D S 2 9 B 3 3 6
C 7 D 4 0 D S 2 9 B 4 3 7
C 7 D 4 0 D S 2 9 C 1 3 - 1 4 3 7 2 7 4 - 6 3 6
C 7 D 4 0 D S 2 9 C 3 3 - 1 4 3 7 2 7 4 - 7 3 6
C 7 D 4 0 D S 2 9 C 4 3 7
C 7 D 4 0 D S 2 9 D 1 3 6
C 7 D 4 0 D S 2 9 D 3 3 - 1 4 3 7 2 7 4 - 8 3 6
C 7 D 4 0 D S 2 9 D 4 3 7
C 7 D 4 0 D S 2 9 E 1 3 6
C 7 D 4 0 D S 2 9 E 3 3 6
C 7 D 4 0 D S 2 9 E 4 3 7
C 7 D 4 0 P F 2 9 0 1 2 4 - 1 4 3 7 2 6 3 - 4 1 4 4
C 7 D 4 0 P F 2 9 0 1 3 4 - 1 4 3 7 2 6 3 - 5 1 4 4
C 7 D 4 0 P F 2 9 0 2 2 1 4 2
C 7 D 4 0 P F 2 9 0 2 3 4 - 1 4 3 7 2 6 3 - 6 1 4 2
C 7 D 4 0 P F 2 9 0 3 2 4 - 1 4 3 7 2 6 3 - 7 1 4 2
C 7 D 4 0 P F 2 9 0 3 3 1 4 2
C 7 D 4 0 P F 2 9 0 4 2 1 4 4
C 7 D 4 0 P F 2 9 0 4 3 4 - 1 4 3 7 2 6 3 - 8 1 4 4
C 7 D 4 0 P F 2 9 1 3 2 1 4 4
C 7 D 4 0 P F 2 9 1 3 3 1 4 4
C 7 D 4 0 P F 2 9 1 4 2 1 4 2
C 7 D 4 0 P F 2 9 1 4 3 1 4 2
C 7 D 4 3 D S 2 9 A 1 3 6
C 7 D 4 3 D S 2 9 A 3 3 6
C 7 D 4 3 D S 2 9 A 4 3 7
C 7 D 4 3 D S 2 9 B 1 3 6
C 7 D 4 3 D S 2 9 B 3 3 6
C 7 D 4 3 D S 2 9 B 4 3 7
C 7 D 4 3 D S 2 9 C 1 3 - 1 4 3 7 2 7 4 - 9 3 6
C 7 D 4 3 D S 2 9 C 3 4 - 1 4 3 7 2 7 4 - 0 3 6
C 7 D 4 3 D S 2 9 C 4 3 7
C 7 D 4 3 D S 2 9 D 1 3 6
C 7 D 4 3 D S 2 9 D 3 3 6
C 7 D 4 3 D S 2 9 D 4 4 - 1 4 3 7 2 7 4 - 1 3 7
C 7 D 4 3 D S 2 9 E 1 3 6
C 7 D 4 3 D S 2 9 E 3 3 6
C 7 D 4 3 D S 2 9 E 4 3 7
C 7 D 4 3 P F 2 9 0 1 2 1 4 4
C 7 D 4 3 P F 2 9 0 1 3 5 - 1 4 3 7 2 6 3 - 0 1 4 4
C 7 D 4 3 P F 2 9 0 2 2 1 4 2
C 7 D 4 3 P F 2 9 0 2 3 1 4 2
C 7 D 4 3 P F 2 9 0 3 2 1 4 2
C 7 D 4 3 P F 2 9 0 3 3 1 4 2
C 7 D 4 3 P F 2 9 0 4 2 1 4 4
C 7 D 4 3 P F 2 9 0 4 3 1 4 4
C 7 D 4 3 P F 2 9 1 3 2 1 4 4
C 7 D 4 3 P F 2 9 1 3 3 1 4 4
C 7 D 4 3 P F 2 9 1 4 2 1 4 2
C 7 D 4 3 P F 2 9 1 4 3 1 4 2
C 7 D 5 0 D S 2 9 A 1 3 6
C 7 D 5 0 D S 2 9 A 3 4 - 1 4 3 7 2 7 4 - 3 3 6
C 7 D 5 0 D S 2 9 A 4 3 7
C 7 D 5 0 D S 2 9 B 1 3 6
C 7 D 5 0 D S 2 9 B 3 5 - 1 4 3 7 2 6 3 - 1 3 6
C 7 D 5 0 D S 2 9 B 4 3 7
C 7 D 5 0 D S 2 9 C 1 4 - 1 4 3 7 2 7 4 - 4 3 6
C 7 D 5 0 D S 2 9 C 3 4 - 1 4 3 7 2 7 4 - 5 3 6
C 7 D 5 0 D S 2 9 C 4 4 - 1 4 3 7 2 7 4 - 6 3 7
C 7 D 5 0 D S 2 9 D 1 3 6
C 7 D 5 0 D S 2 9 D 3 4 - 1 4 3 7 2 7 4 - 8 3 6
C 7 D 5 0 D S 2 9 D 4 3 7
C 7 D 5 0 D S 2 9 E 1 5 - 1 4 3 7 2 7 4 - 0 3 6
C 7 D 5 0 D S 2 9 E 3 3 6
C 7 D 5 0 D S 2 9 E 4 3 7
C 7 D 5 0 P F 2 9 0 1 2 1 4 4
C 7 D 5 0 P F 2 9 0 1 3 5 - 1 4 3 7 2 6 3 - 2 1 4 4
C 7 D 5 0 P F 2 9 0 2 2 1 4 2
C 7 D 5 0 P F 2 9 0 2 3 1 4 2
C 7 D 5 0 P F 2 9 0 3 2 1 4 2
C 7 D 5 0 P F 2 9 0 3 3 5 - 1 4 3 7 2 6 3 - 3 1 4 2
C 7 D 5 0 P F 2 9 0 4 2 1 4 4
C 7 D 5 0 P F 2 9 0 4 3 5 - 1 4 3 7 2 6 3 - 4 1 4 4
C 7 D 5 0 P F 2 9 1 3 2 1 4 4
C 7 D 5 0 P F 2 9 1 3 3 1 4 4
C 7 D 5 0 P F 2 9 1 4 2 1 4 2
C 7 D 5 0 P F 2 9 1 4 3 5 - 1 4 3 7 2 6 3 - 7 1 4 2
C 8 D 0 6 D S 2 9 A 1 3 1
C 8 D 0 6 D S 2 9 A 2 3 1
C 8 D 0 6 D S 2 9 A 3 3 2
C 8 D 0 6 D S 2 9 B 1 3 1
C 8 D 0 6 D S 2 9 B 2 3 1
C 8 D 0 6 D S 2 9 B 3 3 2
C 8 D 0 6 D S 2 9 C 1 2 - 1 4 3 7 2 7 5 - 9 3 1
C 8 D 0 6 D S 2 9 C 2 3 - 1 4 3 7 2 7 5 - 0 3 1
C 8 D 0 6 D S 2 9 C 3 3 - 1 4 3 7 2 7 5 - 1 3 2
C 8 D 0 6 D S 2 9 D 1 3 1
C 8 D 0 6 D S 2 9 D 2 3 1
C 8 D 0 6 D S 2 9 D 3 3 2
C 8 D 0 6 D S 2 9 E 1 3 - 1 4 3 7 2 7 5 - 2 3 1
C 8 D 0 6 D S 2 9 E 2 3 1
C 8 D 0 6 D S 2 9 E 3 3 2
C 8 D 0 6 P F 2 9 0 1 2 1 4 0
C 8 D 0 6 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 0 - 4 1 4 0
C 8 D 0 6 P F 2 9 0 2 2 1 3 8
C 8 D 0 6 P F 2 9 0 2 3 1 3 8
C 8 D 0 6 P F 2 9 0 3 2 1 3 8
C 8 D 0 6 P F 2 9 0 3 3 1 3 8
C 8 D 0 6 P F 2 9 0 4 2 1 4 0
C 8 D 0 6 P F 2 9 0 4 3 1 - 1 4 3 7 2 6 0 - 5 1 4 0
C 8 D 0 6 P F 2 9 1 3 2 1 4 0
C 8 D 0 6 P F 2 9 1 3 3 1 4 0
C 8 D 0 6 P F 2 9 1 4 2 1 3 8
C 8 D 0 6 P F 2 9 1 4 3 1 3 8
C 8 D 1 0 D S 2 9 A 1 3 1
C 8 D 1 0 D S 2 9 A 2 3 1
C 8 D 1 0 D S 2 9 A 3 3 - 1 4 3 7 2 7 5 - 5 3 2
C 8 D 1 0 D S 2 9 B 1 3 1
C 8 D 1 0 D S 2 9 B 2 3 1
C 8 D 1 0 D S 2 9 B 3 3 2
C 8 D 1 0 D S 2 9 C 1 3 - 1 4 3 7 2 7 5 - 6 3 1
C 8 D 1 0 D S 2 9 C 2 3 - 1 4 3 7 2 7 5 - 8 3 1
C 8 D 1 0 D S 2 9 C 3 3 - 1 4 3 7 2 7 5 - 9 3 2
C 8 D 1 0 D S 2 9 D 1 4 - 1 4 3 7 2 7 5 - 0 3 1
C 8 D 1 0 D S 2 9 D 2 3 1
C 8 D 1 0 D S 2 9 D 3 4 - 1 4 3 7 2 7 5 - 1 3 2
C 8 D 1 0 D S 2 9 E 1 3 1
C 8 D 1 0 D S 2 9 E 2 3 1
C 8 D 1 0 D S 2 9 E 3 3 2
C 8 D 1 0 P F 2 9 0 1 2 1 4 0
C 8 D 1 0 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 0 - 0 1 4 0
C 8 D 1 0 P F 2 9 0 2 2 1 3 8
C 8 D 1 0 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 0 - 2 1 3 8
C 8 D 1 0 P F 2 9 0 3 2 1 3 8
C 8 D 1 0 P F 2 9 0 3 3 1 3 8
C 8 D 1 0 P F 2 9 0 4 2 1 4 0
C 8 D 1 0 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 0 - 3 1 4 0
C 8 D 1 0 P F 2 9 1 3 2 1 4 0
C 8 D 1 0 P F 2 9 1 3 3 1 4 0
C 8 D 1 0 P F 2 9 1 4 2 1 3 8
C 8 D 1 0 P F 2 9 1 4 3 1 3 8
C 8 D 1 2 D S 2 9 A 1 3 1
C 8 D 1 2 D S 2 9 A 2 3 1
C 8 D 1 2 D S 2 9 A 3 3 2
C 8 D 1 2 D S 2 9 B 1 3 1
C 8 D 1 2 D S 2 9 B 2 3 1
C 8 D 1 2 D S 2 9 B 3 3 2
C 8 D 1 2 D S 2 9 C 1 4 - 1 4 3 7 2 7 5 - 5 3 1
C 8 D 1 2 D S 2 9 C 2 3 1
C 8 D 1 2 D S 2 9 C 3 4 - 1 4 3 7 2 7 5 - 7 3 2
C 8 D 1 2 D S 2 9 D 1 4 - 1 4 3 7 2 7 5 - 8 3 1
C 8 D 1 2 D S 2 9 D 2 3 1
C 8 D 1 2 D S 2 9 D 3 3 2
C 8 D 1 2 D S 2 9 E 1 5 - 1 4 3 7 2 7 4 - 1 3 1
C 8 D 1 2 D S 2 9 E 2 3 1
C 8 D 1 2 D S 2 9 E 3 3 2
C 8 D 1 2 P F 2 9 0 1 2 1 4 0
C 8 D 1 2 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 0 - 4 1 4 0
C 8 D 1 2 P F 2 9 0 2 2 1 3 8
C 8 D 1 2 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 0 - 5 1 3 8
C 8 D 1 2 P F 2 9 0 3 2 1 3 8
C 8 D 1 2 P F 2 9 0 3 3 1 3 8
C 8 D 1 2 P F 2 9 0 4 2 1 4 0
C 8 D 1 2 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 0 - 6 1 4 0
C 8 D 1 2 P F 2 9 1 3 2 1 4 0
C 8 D 1 2 P F 2 9 1 3 3 1 4 0
C 8 D 1 2 P F 2 9 1 4 2 1 3 8
C 8 D 1 2 P F 2 9 1 4 3 1 3 8
C 8 D 1 5 D S 2 9 A 1 3 1
C 8 D 1 5 D S 2 9 A 2 3 1
C 8 D 1 5 D S 2 9 A 3 3 2
C 8 D 1 5 D S 2 9 B 1 3 1
C 8 D 1 5 D S 2 9 B 2 3 1
C 8 D 1 5 D S 2 9 B 3 5 - 1 4 3 7 2 7 5 - 1 3 2
C 8 D 1 5 D S 2 9 C 1 5 - 1 4 3 7 2 7 5 - 2 3 1
C 8 D 1 5 D S 2 9 C 2 3 1
C 8 D 1 5 D S 2 9 C 3 5 - 1 4 3 7 2 7 5 - 4 3 2
C 8 D 1 5 D S 2 9 D 1 5 - 1 4 3 7 2 7 5 - 5 3 1
C 8 D 1 5 D S 2 9 D 2 5 - 1 4 3 7 2 7 5 - 6 3 1
C 8 D 1 5 D S 2 9 D 3 3 2
C 8 D 1 5 D S 2 9 E 1 3 1
C 8 D 1 5 D S 2 9 E 2 3 1
C 8 D 1 5 D S 2 9 E 3 3 2
C 8 D 1 5 P F 2 9 0 1 2 1 4 0
C 8 D 1 5 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 0 - 7 1 4 0
C 8 D 1 5 P F 2 9 0 2 2 1 3 8
C 8 D 1 5 P F 2 9 0 2 3 2 - 1 4 3 7 2 6 0 - 9 1 3 8
C 8 D 1 5 P F 2 9 0 3 2 1 3 8
C 8 D 1 5 P F 2 9 0 3 3 1 3 8
C 8 D 1 5 P F 2 9 0 4 2 1 4 0
C 8 D 1 5 P F 2 9 0 4 3 3 - 1 4 3 7 2 6 0 - 0 1 4 0
C 8 D 1 5 P F 2 9 1 3 2 1 4 0
C 8 D 1 5 P F 2 9 1 3 3 1 4 0
C 8 D 1 5 P F 2 9 1 4 2 1 3 8
C 8 D 1 5 P F 2 9 1 4 3 1 3 8
C 8 D 1 8 D S 2 9 A 1 3 1
C 8 D 1 8 D S 2 9 A 2 3 1
C 8 D 1 8 D S 2 9 A 3 3 2
C 8 D 1 8 D S 2 9 B 1 3 1
C 8 D 1 8 D S 2 9 B 2 3 1
C 8 D 1 8 D S 2 9 B 3 3 2
C 8 D 1 8 D S 2 9 C 1 5 - 1 4 3 7 2 7 5 - 9 3 1
C 8 D 1 8 D S 2 9 C 2 3 1
C 8 D 1 8 D S 2 9 C 3 6 - 1 4 3 7 2 7 5 - 1 3 2
C 8 D 1 8 D S 2 9 D 1 6 - 1 4 3 7 2 7 5 - 2 3 1
C 8 D 1 8 D S 2 9 D 2 3 1
C 8 D 1 8 D S 2 9 D 3 6 - 1 4 3 7 2 7 5 - 3 3 2
C 8 D 1 8 D S 2 9 E 1 6 - 1 4 3 7 2 7 5 - 4 3 1
C 8 D 1 8 D S 2 9 E 2 3 1
C 8 D 1 8 D S 2 9 E 3 3 2
C 8 D 2 0 D S 2 9 A 1 3 1
C 8 D 2 0 D S 2 9 A 2 3 1
C 8 D 2 0 D S 2 9 A 3 3 2
C 8 D 2 0 D S 2 9 B 1 3 1
C 8 D 2 0 D S 2 9 B 2 3 1
C 8 D 2 0 D S 2 9 B 3 3 2
C 8 D 2 0 D S 2 9 C 1 6 - 1 4 3 7 2 7 5 - 6 3 1
C 8 D 2 0 D S 2 9 C 2 3 1
C 8 D 2 0 D S 2 9 C 3 6 - 1 4 3 7 2 7 5 - 8 3 2
C 8 D 2 0 D S 2 9 D 1 6 - 1 4 3 7 2 7 5 - 9 3 1
C 8 D 2 0 D S 2 9 D 2 3 1
C 8 D 2 0 D S 2 9 D 3 7 - 1 4 3 7 2 7 5 - 0 3 2
C 8 D 2 0 D S 2 9 E 1 3 1
C 8 D 2 0 D S 2 9 E 2 3 1
C 8 D 2 0 D S 2 9 E 3 3 2
C 8 D 2 0 P F 2 9 0 1 2 1 4 0
C 8 D 2 0 P F 2 9 0 1 3 1 4 0
C 8 D 2 0 P F 2 9 0 2 2 1 3 8
C 8 D 2 0 P F 2 9 0 2 3 3 - 1 4 3 7 2 6 0 - 5 1 3 8
C 8 D 2 0 P F 2 9 0 3 2 1 3 8
C 8 D 2 0 P F 2 9 0 3 3 1 3 8
C 8 D 2 0 P F 2 9 0 4 2 1 4 0
C 8 D 2 0 P F 2 9 0 4 3 3 - 1 4 3 7 2 6 0 - 6 1 4 0
C 8 D 2 0 P F 2 9 1 3 2 1 4 0
C 8 D 2 0 P F 2 9 1 3 3 1 4 0
C 8 D 2 0 P F 2 9 1 4 2 1 3 8
C 8 D 2 0 P F 2 9 1 4 3 1 3 8
C 8 D 2 2 D S 2 9 A 1 7 - 1 4 3 7 2 7 5 - 1 3 1
C 8 D 2 2 D S 2 9 A 2 3 1
C 8 D 2 2 D S 2 9 A 3 7 - 1 4 3 7 2 7 5 - 2 3 2
C 8 D 2 2 D S 2 9 B 1 7 - 1 4 3 7 2 7 5 - 3 3 1
C 8 D 2 2 D S 2 9 B 2 3 1
C 8 D 2 2 D S 2 9 B 3 3 2
C 8 D 2 2 D S 2 9 C 1 7 - 1 4 3 7 2 7 5 - 4 3 1
C 8 D 2 2 D S 2 9 C 2 3 1
C 8 D 2 2 D S 2 9 C 3 7 - 1 4 3 7 2 7 5 - 6 3 2
C 8 D 2 2 D S 2 9 D 1 7 - 1 4 3 7 2 7 5 - 7 3 1
C 8 D 2 2 D S 2 9 D 2 3 1
C 8 D 2 2 D S 2 9 D 3 3 2
C 8 D 2 2 D S 2 9 E 1 3 1
C 8 D 2 2 D S 2 9 E 2 3 1
C 8 D 2 2 D S 2 9 E 3 3 2
C 8 D 2 2 P F 2 9 0 1 2 1 4 0
C 8 D 2 2 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 0 - 8 1 4 0
C 8 D 2 2 P F 2 9 0 2 2 1 3 8
C 8 D 2 2 P F 2 9 0 2 3 4 - 1 4 3 7 2 6 0 - 0 1 3 8
C 8 D 2 2 P F 2 9 0 3 2 1 3 8
C 8 D 2 2 P F 2 9 0 3 3 1 3 8
C 8 D 2 2 P F 2 9 0 4 2 1 4 0
C 8 D 2 2 P F 2 9 0 4 3 4 - 1 4 3 7 2 6 0 - 1 1 4 0
C 8 D 2 2 P F 2 9 1 3 2 1 4 0
C 8 D 2 2 P F 2 9 1 3 3 1 4 0
C 8 D 2 2 P F 2 9 1 4 2 1 3 8
C 8 D 2 2 P F 2 9 1 4 3 1 3 8
C 8 D 2 5 D S 2 9 A 1 7 - 1 4 3 7 2 7 5 - 8 3 1
C 8 D 2 5 D S 2 9 A 2 3 1
C 8 D 2 5 D S 2 9 A 3 7 - 1 4 3 7 2 7 5 - 9 3 2
C 8 D 2 5 D S 2 9 B 1 3 1
C 8 D 2 5 D S 2 9 B 2 3 1
C 8 D 2 5 D S 2 9 B 3 3 2
C 8 D 2 5 D S 2 9 C 1 8 - 1 4 3 7 2 7 5 - 0 3 1
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
200
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 8 D 2 5 D S 2 9 C 2 3 1
C 8 D 2 5 D S 2 9 C 3 8 - 1 4 3 7 2 7 5 - 2 3 2
C 8 D 2 5 D S 2 9 D 1 8 - 1 4 3 7 2 7 5 - 3 3 1
C 8 D 2 5 D S 2 9 D 2 3 1
C 8 D 2 5 D S 2 9 D 3 8 - 1 4 3 7 2 7 5 - 4 3 2
C 8 D 2 5 D S 2 9 E 1 3 1
C 8 D 2 5 D S 2 9 E 2 3 1
C 8 D 2 5 D S 2 9 E 3 3 2
C 8 D 2 5 P F 2 9 0 1 2 1 4 0
C 8 D 2 5 P F 2 9 0 1 3 4 - 1 4 3 7 2 6 0 - 5 1 4 0
C 8 D 2 5 P F 2 9 0 2 2 1 3 8
C 8 D 2 5 P F 2 9 0 2 3 4 - 1 4 3 7 2 6 0 - 8 1 3 8
C 8 D 2 5 P F 2 9 0 3 2 1 3 8
C 8 D 2 5 P F 2 9 0 3 3 4 - 1 4 3 7 2 6 0 - 9 1 3 8
C 8 D 2 5 P F 2 9 0 4 2 1 4 0
C 8 D 2 5 P F 2 9 0 4 3 1 4 0
C 8 D 2 5 P F 2 9 1 3 2 1 4 0
C 8 D 2 5 P F 2 9 1 3 3 1 4 0
C 8 D 2 5 P F 2 9 1 4 2 1 3 8
C 8 D 2 5 P F 2 9 1 4 3 1 3 8
C 8 D 2 8 D S 2 9 A 1 3 1
C 8 D 2 8 D S 2 9 A 2 3 1
C 8 D 2 8 D S 2 9 A 3 3 2
C 8 D 2 8 D S 2 9 B 1 3 1
C 8 D 2 8 D S 2 9 B 2 3 1
C 8 D 2 8 D S 2 9 B 3 3 2
C 8 D 2 8 D S 2 9 C 1 8 - 1 4 3 7 2 7 5 - 5 3 1
C 8 D 2 8 D S 2 9 C 2 3 1
C 8 D 2 8 D S 2 9 C 3 8 - 1 4 3 7 2 7 5 - 8 3 2
C 8 D 2 8 D S 2 9 D 1 8 - 1 4 3 7 2 7 5 - 9 3 1
C 8 D 2 8 D S 2 9 D 2 3 1
C 8 D 2 8 D S 2 9 D 3 9 - 1 4 3 7 2 7 5 - 0 3 2
C 8 D 2 8 D S 2 9 E 1 3 1
C 8 D 2 8 D S 2 9 E 2 3 1
C 8 D 2 8 D S 2 9 E 3 3 2
C 8 D 2 8 P F 2 9 0 1 2 9 - 1 4 3 7 2 7 5 - 1 1 4 0
C 8 D 2 8 P F 2 9 0 1 3 1 4 0
C 8 D 2 8 P F 2 9 0 2 2 1 3 8
C 8 D 2 8 P F 2 9 0 2 3 5 - 1 4 3 7 2 6 0 - 5 1 3 8
C 8 D 2 8 P F 2 9 0 3 2 1 3 8
C 8 D 2 8 P F 2 9 0 3 3 1 3 8
C 8 D 2 8 P F 2 9 0 4 2 1 4 0
C 8 D 2 8 P F 2 9 0 4 3 1 4 0
C 8 D 2 8 P F 2 9 1 3 2 1 4 0
C 8 D 2 8 P F 2 9 1 3 3 1 4 0
C 8 D 2 8 P F 2 9 1 4 2 1 3 8
C 8 D 2 8 P F 2 9 1 4 3 1 3 8
C 8 D 3 0 D S 2 9 A 1 3 1
C 8 D 3 0 D S 2 9 A 2 3 1
C 8 D 3 0 D S 2 9 A 3 3 2
C 8 D 3 0 D S 2 9 B 1 3 1
C 8 D 3 0 D S 2 9 B 2 3 1
C 8 D 3 0 D S 2 9 B 3 3 2
C 8 D 3 0 D S 2 9 C 1 9 - 1 4 3 7 2 7 5 - 3 3 1
C 8 D 3 0 D S 2 9 C 2 3 1
C 8 D 3 0 D S 2 9 C 3 9 - 1 4 3 7 2 7 5 - 5 3 2
C 8 D 3 0 D S 2 9 D 1 9 - 1 4 3 7 2 7 5 - 6 3 1
C 8 D 3 0 D S 2 9 D 2 3 1
C 8 D 3 0 D S 2 9 D 3 9 - 1 4 3 7 2 7 5 - 7 3 2
C 8 D 3 0 D S 2 9 E 1 9 - 1 4 3 7 2 7 5 - 8 3 1
C 8 D 3 0 D S 2 9 E 2 3 1
C 8 D 3 0 D S 2 9 E 3 9 - 1 4 3 7 2 7 5 - 9 3 2
C 8 D 3 0 P F 2 9 0 1 2 1 4 0
C 8 D 3 0 P F 2 9 0 1 3 5 - 1 4 3 7 2 6 0 - 6 1 4 0
C 8 D 3 0 P F 2 9 0 2 2 1 3 8
C 8 D 3 0 P F 2 9 0 2 3 5 - 1 4 3 7 2 6 0 - 8 1 3 8
C 8 D 3 0 P F 2 9 0 3 2 1 3 8
C 8 D 3 0 P F 2 9 0 3 3 1 3 8
C 8 D 3 0 P F 2 9 0 4 2 1 4 0
C 8 D 3 0 P F 2 9 0 4 3 6 - 1 4 3 7 2 6 0 - 1 1 4 0
C 8 D 3 0 P F 2 9 1 3 2 1 4 0
C 8 D 3 0 P F 2 9 1 3 3 6 - 1 4 3 7 2 6 0 - 4 1 4 0
C 8 D 3 0 P F 2 9 1 4 2 1 3 8
C 8 D 3 0 P F 2 9 1 4 3 1 3 8
C 8 D 3 1 D S 2 9 A 1 3 1
C 8 D 3 1 D S 2 9 A 2 3 1
C 8 D 3 1 D S 2 9 A 3 0 - 1 4 3 7 2 7 6 - 2 3 2
C 8 D 3 1 D S 2 9 B 1 3 1
C 8 D 3 1 D S 2 9 B 2 3 1
C 8 D 3 1 D S 2 9 B 3 3 2
C 8 D 3 1 D S 2 9 C 1 0 - 1 4 3 7 2 7 6 - 3 3 1
C 8 D 3 1 D S 2 9 C 2 0 - 1 4 3 7 2 7 6 - 5 3 1
C 8 D 3 1 D S 2 9 C 3 0 - 1 4 3 7 2 7 6 - 6 3 2
C 8 D 3 1 D S 2 9 D 1 0 - 1 4 3 7 2 7 6 - 8 3 1
C 8 D 3 1 D S 2 9 D 2 3 1
C 8 D 3 1 D S 2 9 D 3 0 - 1 4 3 7 2 7 6 - 9 3 2
C 8 D 3 1 D S 2 9 E 1 3 1
C 8 D 3 1 D S 2 9 E 2 3 1
C 8 D 3 1 D S 2 9 E 3 3 2
C 8 D 3 1 P F 2 9 0 1 2 1 4 0
C 8 D 3 1 P F 2 9 0 1 3 6 - 1 4 3 7 2 6 0 - 5 1 4 0
C 8 D 3 1 P F 2 9 0 2 2 1 3 8
C 8 D 3 1 P F 2 9 0 2 3 6 - 1 4 3 7 2 6 0 - 6 1 3 8
C 8 D 3 1 P F 2 9 0 3 2 1 3 8
C 8 D 3 1 P F 2 9 0 3 3 1 3 8
C 8 D 3 1 P F 2 9 0 4 2 1 4 0
C 8 D 3 1 P F 2 9 0 4 3 6 - 1 4 3 7 2 6 0 - 7 1 4 0
C 8 D 3 1 P F 2 9 1 3 2 6 - 1 4 3 7 2 6 0 - 8 1 4 0
C 8 D 3 1 P F 2 9 1 3 3 6 - 1 4 3 7 2 6 0 - 9 1 4 0
C 8 D 3 1 P F 2 9 1 4 2 1 3 8
C 8 D 3 1 P F 2 9 1 4 3 1 3 8
C 8 D 3 5 D S 2 9 A 1 1 - 1 4 3 7 2 7 6 - 0 3 1
C 8 D 3 5 D S 2 9 A 2 3 1
C 8 D 3 5 D S 2 9 A 3 1 - 1 4 3 7 2 7 6 - 1 3 2
C 8 D 3 5 D S 2 9 B 1 3 1
C 8 D 3 5 D S 2 9 B 2 3 1
C 8 D 3 5 D S 2 9 B 3 3 2
C 8 D 3 5 D S 2 9 C 1 3 1
C 8 D 3 5 D S 2 9 C 2 3 1
C 8 D 3 5 D S 2 9 C 3 1 - 1 4 3 7 2 7 6 - 3 3 2
C 8 D 3 5 D S 2 9 D 1 3 1
C 8 D 3 5 D S 2 9 D 2 3 1
C 8 D 3 5 D S 2 9 D 3 3 2
C 8 D 3 5 D S 2 9 E 1 3 1
C 8 D 3 5 D S 2 9 E 2 3 1
C 8 D 3 5 D S 2 9 E 3 1 - 1 4 3 7 2 7 6 - 4 3 2
C 8 D 3 5 P F 2 9 0 1 2 1 4 0
C 8 D 3 5 P F 2 9 0 1 3 1 4 0
C 8 D 3 5 P F 2 9 0 2 2 1 3 8
C 8 D 3 5 P F 2 9 0 2 3 7 - 1 4 3 7 2 6 0 - 3 1 3 8
C 8 D 3 5 P F 2 9 0 3 2 1 3 8
C 8 D 3 5 P F 2 9 0 3 3 1 3 8
C 8 D 3 5 P F 2 9 0 4 2 1 4 0
C 8 D 3 5 P F 2 9 0 4 3 1 4 0
C 8 D 3 5 P F 2 9 1 3 2 1 4 0
C 8 D 3 5 P F 2 9 1 3 3 1 4 0
C 8 D 3 5 P F 2 9 1 4 2 1 3 8
C 8 D 3 5 P F 2 9 1 4 3 1 3 8
C 8 D 3 6 D S 2 9 A 1 3 1
C 8 D 3 6 D S 2 9 A 2 3 1
C 8 D 3 6 D S 2 9 A 3 1 - 1 4 3 7 2 7 6 - 5 3 2
C 8 D 3 6 D S 2 9 B 1 3 1
C 8 D 3 6 D S 2 9 B 2 3 1
C 8 D 3 6 D S 2 9 B 3 3 2
C 8 D 3 6 D S 2 9 C 1 1 - 1 4 3 7 2 7 6 - 6 3 1
C 8 D 3 6 D S 2 9 C 2 1 - 1 4 3 7 2 7 6 - 8 3 1
C 8 D 3 6 D S 2 9 C 3 1 - 1 4 3 7 2 7 6 - 9 3 2
C 8 D 3 6 D S 2 9 D 1 2 - 1 4 3 7 2 7 6 - 0 3 1
C 8 D 3 6 D S 2 9 D 2 2 - 1 4 3 7 2 7 6 - 1 3 1
C 8 D 3 6 D S 2 9 D 3 2 - 1 4 3 7 2 7 6 - 2 3 2
C 8 D 3 6 D S 2 9 E 1 3 1
C 8 D 3 6 D S 2 9 E 2 3 1
C 8 D 3 6 D S 2 9 E 3 2 - 1 4 3 7 2 7 6 - 3 3 2
C 8 D 3 6 P F 2 9 0 1 2 1 4 0
C 8 D 3 6 P F 2 9 0 1 3 7 - 1 4 3 7 2 6 0 - 7 1 4 0
C 8 D 3 6 P F 2 9 0 2 2 7 - 1 4 3 7 2 6 0 - 9 1 3 8
C 8 D 3 6 P F 2 9 0 2 3 8 - 1 4 3 7 2 6 0 - 0 1 3 8
C 8 D 3 6 P F 2 9 0 3 2 1 3 8
C 8 D 3 6 P F 2 9 0 3 3 8 - 1 4 3 7 2 6 0 - 1 1 3 8
C 8 D 3 6 P F 2 9 0 4 2 1 4 0
C 8 D 3 6 P F 2 9 0 4 3 8 - 1 4 3 7 2 6 0 - 2 1 4 0
C 8 D 3 6 P F 2 9 1 3 2 1 4 0
C 8 D 3 6 P F 2 9 1 3 3 1 4 0
C 8 D 3 6 P F 2 9 1 4 2 1 3 8
C 8 D 3 6 P F 2 9 1 4 3 1 3 8
C 8 D 4 0 D S 2 9 A 1 2 - 1 4 3 7 2 7 6 - 5 3 1
C 8 D 4 0 D S 2 9 A 2 3 1
C 8 D 4 0 D S 2 9 A 3 2 - 1 4 3 7 2 7 6 - 6 3 2
C 8 D 4 0 D S 2 9 B 1 3 1
C 8 D 4 0 D S 2 9 B 2 3 1
C 8 D 4 0 D S 2 9 B 3 3 2
C 8 D 4 0 D S 2 9 C 1 2 - 1 4 3 7 2 7 6 - 7 3 1
C 8 D 4 0 D S 2 9 C 2 3 1
C 8 D 4 0 D S 2 9 C 3 2 - 1 4 3 7 2 7 6 - 9 3 2
C 8 D 4 0 D S 2 9 D 1 3 - 1 4 3 7 2 7 6 - 0 3 1
C 8 D 4 0 D S 2 9 D 2 3 1
C 8 D 4 0 D S 2 9 D 3 3 - 1 4 3 7 2 7 6 - 1 3 2
C 8 D 4 0 D S 2 9 E 1 3 1
C 8 D 4 0 D S 2 9 E 2 3 1
C 8 D 4 0 D S 2 9 E 3 3 2
C 8 D 4 0 P F 2 9 0 1 2 1 4 0
C 8 D 4 0 P F 2 9 0 1 3 1 4 0
C 8 D 4 0 P F 2 9 0 2 2 1 3 8
C 8 D 4 0 P F 2 9 0 2 3 8 - 1 4 3 7 2 6 0 - 4 1 3 8
C 8 D 4 0 P F 2 9 0 3 2 1 3 8
C 8 D 4 0 P F 2 9 0 3 3 1 3 8
C 8 D 4 0 P F 2 9 0 4 2 1 4 0
C 8 D 4 0 P F 2 9 0 4 3 8 - 1 4 3 7 2 6 0 - 6 1 4 0
C 8 D 4 0 P F 2 9 1 3 2 1 4 0
C 8 D 4 0 P F 2 9 1 3 3 1 4 0
C 8 D 4 0 P F 2 9 1 4 2 1 3 8
C 8 D 4 0 P F 2 9 1 4 3 1 3 8
C 8 D 4 3 D S 2 9 A 1 3 1
C 8 D 4 3 D S 2 9 A 2 3 1
C 8 D 4 3 D S 2 9 A 3 3 2
C 8 D 4 3 D S 2 9 B 1 3 1
C 8 D 4 3 D S 2 9 B 2 3 1
C 8 D 4 3 D S 2 9 B 3 3 2
C 8 D 4 3 D S 2 9 C 1 3 - 1 4 3 7 2 7 6 - 2 3 1
C 8 D 4 3 D S 2 9 C 2 3 1
C 8 D 4 3 D S 2 9 C 3 3 - 1 4 3 7 2 7 6 - 3 3 2
C 8 D 4 3 D S 2 9 D 1 3 1
C 8 D 4 3 D S 2 9 D 2 3 1
C 8 D 4 3 D S 2 9 D 3 3 - 1 4 3 7 2 7 6 - 4 3 2
C 8 D 4 3 D S 2 9 E 1 3 - 1 4 3 7 2 7 6 - 5 3 1
C 8 D 4 3 D S 2 9 E 2 3 1
C 8 D 4 3 D S 2 9 E 3 3 2
C 8 D 4 3 P F 2 9 0 1 2 8 - 1 4 3 7 2 6 0 - 9 1 4 0
C 8 D 4 3 P F 2 9 0 1 3 9 - 1 4 3 7 2 6 0 - 0 1 4 0
C 8 D 4 3 P F 2 9 0 2 2 9 - 1 4 3 7 2 6 0 - 2 1 3 8
C 8 D 4 3 P F 2 9 0 2 3 9 - 1 4 3 7 2 6 0 - 3 1 3 8
C 8 D 4 3 P F 2 9 0 3 2 1 3 8
C 8 D 4 3 P F 2 9 0 3 3 1 3 8
C 8 D 4 3 P F 2 9 0 4 2 1 4 0
C 8 D 4 3 P F 2 9 0 4 3 1 4 0
C 8 D 4 3 P F 2 9 1 3 2 1 4 0
C 8 D 4 3 P F 2 9 1 3 3 1 4 0
C 8 D 4 3 P F 2 9 1 4 2 1 3 8
C 8 D 4 3 P F 2 9 1 4 3 1 3 8
C 8 D 5 0 D S 2 9 A 1 3 - 1 4 3 7 2 7 6 - 8 3 1
C 8 D 5 0 D S 2 9 A 2 3 2
C 8 D 5 0 D S 2 9 A 3 3 - 1 4 3 7 2 7 6 - 9 3 2
C 8 D 5 0 D S 2 9 B 1 3 1
C 8 D 5 0 D S 2 9 B 2 3 2
C 8 D 5 0 D S 2 9 B 3 3 2
C 8 D 5 0 D S 2 9 C 1 4 - 1 4 3 7 2 7 6 - 0 3 1
C 8 D 5 0 D S 2 9 C 2 3 2
C 8 D 5 0 D S 2 9 C 3 4 - 1 4 3 7 2 7 6 - 2 3 2
C 8 D 5 0 D S 2 9 D 1 4 - 1 4 3 7 2 7 6 - 3 3 1
C 8 D 5 0 D S 2 9 D 2 3 2
C 8 D 5 0 D S 2 9 D 3 3 2
C 8 D 5 0 D S 2 9 E 1 3 1
C 8 D 5 0 D S 2 9 E 2 3 2
C 8 D 5 0 D S 2 9 E 3 3 2
C 8 D 5 0 P F 2 9 0 1 2 1 4 0
C 8 D 5 0 P F 2 9 0 1 3 9 - 1 4 3 7 2 6 0 - 9 1 4 0
C 8 D 5 0 P F 2 9 0 2 2 1 3 8
C 8 D 5 0 P F 2 9 0 2 3 0 - 1 4 3 7 2 6 1 - 2 1 3 8
C 8 D 5 0 P F 2 9 0 3 2 1 3 8
C 8 D 5 0 P F 2 9 0 3 3 0 - 1 4 3 7 2 6 1 - 5 1 3 8
C 8 D 5 0 P F 2 9 0 4 2 1 4 0
C 8 D 5 0 P F 2 9 0 4 3 0 - 1 4 3 7 2 6 1 - 6 1 4 0
C 8 D 5 0 P F 2 9 1 3 2 1 4 0
C 8 D 5 0 P F 2 9 1 3 3 1 4 0
C 8 D 5 0 P F 2 9 1 4 2 1 3 8
C 8 D 5 0 P F 2 9 1 4 3 1 3 8
C 8 D 5 2 D S 2 9 C 1 M 1 9 1 4 - 1 4 3 7 2 7 6 - 6 2 9
C 8 D 5 2 D S 2 9 C 1 M 1 9 5 4 - 1 4 3 7 2 7 6 - 7 2 9
C 8 D 6 0 D S 2 9 A 1 5 - 1 4 3 7 2 7 6 - 1 3 1
C 8 D 6 0 D S 2 9 A 2 3 2
C 8 D 6 0 D S 2 9 A 3 5 - 1 4 3 7 2 7 6 - 2 3 2
C 8 D 6 0 D S 2 9 B 1 3 1
C 8 D 6 0 D S 2 9 B 2 3 2
C 8 D 6 0 D S 2 9 B 3 5 - 1 4 3 7 2 7 6 - 3 3 2
C 8 D 6 0 D S 2 9 C 1 5 - 1 4 3 7 2 7 6 - 4 3 1
C 8 D 6 0 D S 2 9 C 2 3 2
C 8 D 6 0 D S 2 9 C 3 3 2
C 8 D 6 0 D S 2 9 D 1 5 - 1 4 3 7 2 7 6 - 7 3 1
C 8 D 6 0 D S 2 9 D 2 3 2
C 8 D 6 0 D S 2 9 D 3 3 2
C 8 D 6 0 D S 2 9 E 1 3 1
C 8 D 6 0 D S 2 9 E 2 3 2
C 8 D 6 0 D S 2 9 E 3 3 2
C 8 D 6 0 P F 2 9 0 1 2 1 4 0
C 8 D 6 0 P F 2 9 0 1 3 5 - 1 4 3 7 2 7 6 - 8 1 4 0
C 8 D 6 0 P F 2 9 0 2 2 1 3 8
C 8 D 6 0 P F 2 9 0 2 3 1 - 1 4 3 7 2 6 1 - 1 1 3 8
C 8 D 6 0 P F 2 9 0 3 2 1 3 8
C 8 D 6 0 P F 2 9 0 3 3 1 3 8
C 8 D 6 0 P F 2 9 0 4 2 1 4 0
C 8 D 6 0 P F 2 9 0 4 3 1 4 0
C 8 D 6 0 P F 2 9 1 3 2 1 4 0
C 8 D 6 0 P F 2 9 1 3 3 1 4 0
C 8 D 6 0 P F 2 9 1 4 2 1 3 8
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
201
Part Number Cross Reference—Acquired Part Number to Tyco Part Number
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
Acquired T y c o P a g e
Part Part N u m b e r
N u m b e r N u m b e r
C 8 D 6 0 P F 2 9 1 4 3 1 3 8
C 9 D 0 2 0 P F 6 0 0 4 8 3 - 1 4 3 7 2 6 4 - 4 1 2 9
C 9 D 0 3 0 P F 6 0 0 4 8 3 - 1 4 3 7 2 6 4 - 5 1 2 9
C 9 D 0 4 0 P F 6 0 0 4 8 1 2 9
C 9 D 0 5 0 P F 6 0 0 4 8 1 2 9
C 9 D 0 6 0 P F 6 0 0 4 8 3 - 1 4 3 7 2 6 4 - 6 1 2 9
W 8 D 1 8 D S 2 9 0 6 3 3 4
W 8 D 1 8 D S 2 9 0 9 3 3 4
W 8 D 1 8 P F 2 9 0 1 2 1 3 4
W 8 D 1 8 P F 2 9 0 1 3 1 3 4
W 8 D 1 8 P F 2 9 0 4 2 1 3 4
W 8 D 1 8 P F 2 9 0 4 3 1 3 4
W 8 D 1 8 P F 2 9 0 6 2 1 3 6
W 8 D 1 8 P F 2 9 0 6 3 1 - 1 4 3 7 2 6 5 - 0 1 3 6
W 8 D 1 8 P F 2 9 0 9 2 1 3 6
W 8 D 1 8 P F 2 9 0 9 3 1 3 6
W 8 D 2 0 D S 2 9 0 6 3 3 4
W 8 D 2 0 D S 2 9 0 9 3 3 4
W 8 D 2 0 P F 2 9 0 1 2 1 3 4
W 8 D 2 0 P F 2 9 0 1 3 1 3 4
W 8 D 2 0 P F 2 9 0 4 2 1 3 4
W 8 D 2 0 P F 2 9 0 4 3 1 3 4
W 8 D 2 0 P F 2 9 0 6 2 1 3 6
W 8 D 2 0 P F 2 9 0 6 3 1 3 6
W 8 D 2 0 P F 2 9 0 9 2 1 3 6
W 8 D 2 0 P F 2 9 0 9 3 1 3 6
W 8 D 2 2 D S 2 9 0 6 3 3 4
W 8 D 2 2 D S 2 9 0 9 3 3 4
W 8 D 2 2 P F 2 9 0 1 2 1 3 4
W 8 D 2 2 P F 2 9 0 1 3 1 3 4
W 8 D 2 2 P F 2 9 0 4 2 1 3 4
W 8 D 2 2 P F 2 9 0 4 3 1 - 1 4 3 7 2 6 5 - 2 1 3 4
W 8 D 2 2 P F 2 9 0 6 2 1 3 6
W 8 D 2 2 P F 2 9 0 6 3 1 3 6
W 8 D 2 2 P F 2 9 0 9 2 1 3 6
W 8 D 2 2 P F 2 9 0 9 3 1 3 6
W 8 D 2 5 D S 2 9 0 6 3 3 4
W 8 D 2 5 D S 2 9 0 9 3 3 4
W 8 D 2 5 P F 2 9 0 1 2 1 3 4
W 8 D 2 5 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 5 - 3 1 3 4
W 8 D 2 5 P F 2 9 0 4 2 1 3 4
W 8 D 2 5 P F 2 9 0 4 3 1 3 4
W 8 D 2 5 P F 2 9 0 6 2 1 3 6
W 8 D 2 5 P F 2 9 0 6 3 1 - 1 4 3 7 2 6 5 - 4 1 3 6
W 8 D 2 5 P F 2 9 0 9 2 1 3 6
W 8 D 2 5 P F 2 9 0 9 3 1 - 1 4 3 7 2 6 5 - 5 1 3 6
W 8 D 2 8 D S 2 9 0 6 3 3 4
W 8 D 2 8 D S 2 9 0 9 3 3 4
W 8 D 2 8 P F 2 9 0 1 2 1 3 4
W 8 D 2 8 P F 2 9 0 1 3 1 - 1 4 3 7 2 6 5 - 6 1 3 4
W 8 D 2 8 P F 2 9 0 4 2 1 3 4
W 8 D 2 8 P F 2 9 0 4 3 1 3 4
W 8 D 2 8 P F 2 9 0 6 2 1 3 6
W 8 D 2 8 P F 2 9 0 6 3 1 3 6
W 8 D 2 8 P F 2 9 0 9 2 1 3 6
W 8 D 2 8 P F 2 9 0 9 3 1 - 1 4 3 7 2 6 5 - 7 1 3 6
W 8 D 3 0 D S 2 9 0 6 3 3 4
W 8 D 3 0 D S 2 9 0 9 3 3 4
W 8 D 3 0 P F 2 9 0 1 2 1 3 4
W 8 D 3 0 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 5 - 0 1 3 4
W 8 D 3 0 P F 2 9 0 4 2 1 3 4
W 8 D 3 0 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 5 - 1 1 3 4
W 8 D 3 0 P F 2 9 0 6 2 1 3 6
W 8 D 3 0 P F 2 9 0 6 3 1 3 6
W 8 D 3 0 P F 2 9 0 9 2 1 3 6
W 8 D 3 0 P F 2 9 0 9 3 1 3 6
W 8 D 3 5 D S 2 9 0 6 3 3 4
W 8 D 3 5 D S 2 9 0 9 3 3 4
W 8 D 3 5 P F 2 9 0 1 2 1 3 4
W 8 D 3 5 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 5 - 3 1 3 4
W 8 D 3 5 P F 2 9 0 4 2 1 3 4
W 8 D 3 5 P F 2 9 0 4 3 1 3 4
W 8 D 3 5 P F 2 9 0 6 2 1 3 6
W 8 D 3 5 P F 2 9 0 6 3 2 - 1 4 3 7 2 6 5 - 5 1 3 6
W 8 D 3 5 P F 2 9 0 9 2 1 3 6
W 8 D 3 5 P F 2 9 0 9 3 1 3 6
W 8 D 3 6 D S 2 9 0 6 3 3 4
W 8 D 3 6 D S 2 9 0 9 3 3 4
W 8 D 3 6 P F 2 9 0 1 2 1 3 4
W 8 D 3 6 P F 2 9 0 1 3 2 - 1 4 3 7 2 6 5 - 6 1 3 4
W 8 D 3 6 P F 2 9 0 4 2 1 3 4
W 8 D 3 6 P F 2 9 0 4 3 2 - 1 4 3 7 2 6 5 - 7 1 3 4
W 8 D 3 6 P F 2 9 0 6 2 1 3 6
W 8 D 3 6 P F 2 9 0 6 3 1 3 6
W 8 D 3 6 P F 2 9 0 9 2 1 3 6
W 8 D 3 6 P F 2 9 0 9 3 2 - 1 4 3 7 2 6 5 - 8 1 3 6
W 8 D 4 0 D S 2 9 0 6 3 3 4
W 8 D 4 0 D S 2 9 0 9 3 3 4
W 8 D 4 0 P F 2 9 0 1 2 1 3 4
W 8 D 4 0 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 5 - 0 1 3 4
W 8 D 4 0 P F 2 9 0 4 2 1 3 4
W 8 D 4 0 P F 2 9 0 4 3 1 3 4
W 8 D 4 0 P F 2 9 0 6 2 1 3 6
W 8 D 4 0 P F 2 9 0 6 3 1 3 6
W 8 D 4 0 P F 2 9 0 9 2 1 3 6
W 8 D 4 0 P F 2 9 0 9 3 1 3 6
W 8 D 4 3 D S 2 9 0 6 3 3 4
W 8 D 4 3 D S 2 9 0 9 3 3 4
W 8 D 4 3 P F 2 9 0 1 2 1 3 4
W 8 D 4 3 P F 2 9 0 1 3 1 3 4
W 8 D 4 3 P F 2 9 0 4 2 1 3 4
W 8 D 4 3 P F 2 9 0 4 3 1 3 4
W 8 D 4 3 P F 2 9 0 6 2 1 3 6
W 8 D 4 3 P F 2 9 0 6 3 1 3 6
W 8 D 4 3 P F 2 9 0 9 2 1 3 6
W 8 D 4 3 P F 2 9 0 9 3 1 3 6
W 8 D 4 5 D S 2 9 0 6 3 3 4
W 8 D 4 5 D S 2 9 0 9 3 3 4
W 8 D 4 5 P F 2 9 0 1 2 1 3 4
W 8 D 4 5 P F 2 9 0 1 3 1 3 4
W 8 D 4 5 P F 2 9 0 4 2 1 3 4
W 8 D 4 5 P F 2 9 0 4 3 1 3 4
W 8 D 4 5 P F 2 9 0 6 2 1 3 6
W 8 D 4 5 P F 2 9 0 6 3 1 3 6
W 8 D 4 5 P F 2 9 0 9 2 1 3 6
W 8 D 4 5 P F 2 9 0 9 3 1 3 6
W 8 D 5 0 D S 2 9 0 6 3 3 4
W 8 D 5 0 D S 2 9 0 9 3 3 4
W 8 D 5 0 P F 2 9 0 1 2 3 - 1 4 3 7 2 6 5 - 4 1 3 4
W 8 D 5 0 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 5 - 5 1 3 4
W 8 D 5 0 P F 2 9 0 4 2 1 3 4
W 8 D 5 0 P F 2 9 0 4 3 3 - 1 4 3 7 2 6 5 - 6 1 3 4
W 8 D 5 0 P F 2 9 0 6 2 3 - 1 4 3 7 2 6 5 - 7 1 3 6
W 8 D 5 0 P F 2 9 0 6 3 1 3 6
W 8 D 5 0 P F 2 9 0 9 2 1 3 6
W 8 D 5 0 P F 2 9 0 9 3 1 3 6
W 8 D 6 0 D S 2 9 0 6 3 3 4
W 8 D 6 0 D S 2 9 0 9 3 3 4
W 8 D 6 0 P F 2 9 0 1 2 1 3 4
W 8 D 6 0 P F 2 9 0 1 3 3 - 1 4 3 7 2 6 5 - 9 1 3 4
W 8 D 6 0 P F 2 9 0 4 2 1 3 4
W 8 D 6 0 P F 2 9 0 4 3 1 3 4
W 8 D 6 0 P F 2 9 0 6 2 1 3 6
W 8 D 6 0 P F 2 9 0 6 3 1 3 6
W 8 D 6 0 P F 2 9 0 9 2 1 3 6
W 8 D 6 0 P F 2 9 0 9 3 1 3 6
Card Edge Connectors
202
Catalog 1654080 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in bold Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are imperial equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
For additional component
solutions for Industrial
Machinery, Instrumentation,
Security, and related appli-
cations, request the follow-
ing brochures:
Brochure No. 889439 –
Industrial Machinery
Brochure No. 1307285 –
Instrumentation
Brochure No. 1308325 –
Security
These brochures list cata-
log sources for connectors,
switches, terminal blocks,
relays, timers, circuit break-
ers, and cable assemblies
available from Tyco
Electronics.
Related Product Information
1654080–7.5M–SK–CAD–7-03–0G3B Tyco Electronics Corporation
Printed in U.S.A. www.tycoelectronics.com
Global Contacts
Americas
Asia/Pacific
Argentina – Buenos Aires
Phone: +54-11-4733-2200
Fax: +54-11-4733-2250
Brasil – São Paulo
Phone: +55-11-3611-1311
Fax: +55-11-3611-0397
Canada – Markham
Phone: +905-475-6222
Fax: +905-474-5520
Product Information Center:
(Technical Support)
Phone: +905-470-4425
Fax: +905-474-5525
Colombia – Bogota
Phone: +57-1-240-9396
Fax: +57-1-660-0206
Mexico – Mexico City
Phone: +52-55-5-729-0425
Fax: +52-55-5-398-1430
United States – Harrisburg, PA
Phone: +717-564-0100
Fax: +717-986-7575
Product Information Center:
(Technical Support)
Phone: +800-522-6752
Fax: +717-986-7575
Australia – Sydney
Phone: +61-2-9840-8200
Fax: +61-2-9899-5649
Product Information Center:
(Technical Support)
Phone: +61-2-9554-2600
Fax: +61-2-9502-2556
India – Bangalore
Phone: +91-80-841-0200
Fax: +91-80-841-0210
Indonesia – Jakarta
Phone: +6221-526-7852
Fax: +6221-526-7856
Japan – Kawasaki, Kanagawa
Phone: +81-44-844-8079
Fax: +81-44-844-8733
Product Information Center:
(Technical Support)
Phone: +81-44-844-8013
Fax: +81-44-812-3200
Raychem Products
Phone: +81-44-900-5102
Fax: +81-44-5025-5027
Korea – Seoul
Phone: +82-2-3274-0535
Fax: +82-2-3274-0524/0531
Malaysia – Selangor
Phone: +60-3-7053055
Fax: +60-3-7053066
New Zealand – Auckland
Phone: +64-9-634-4580
Fax: +64-9-634-4586
Philippines – Makati City
Phone: +632-867-8641
Fax: +632-867-8661
People’s Republic of China
Hong Kong
Phone: +852-2735-1628
Fax: +852-2735-0243
Shanghai
Phone: +86-21-6485-0602
Fax: +86-21-6485-0728
Shunde
Phone: +86-765-775-1368
Fax: +86-765-775-2823
Singapore – Singapore
Phone: +65-482-0311
Fax: +65-482-1012
Raychem Products
Phone: +65-486-6151
Fax: +65-654-5514
Taiwan – Taipei
Phone: +886-2-2664-9977
Fax: +886-2-2664-9900
Thailand – Bangkok
Phone: +66-2-955-0500
Fax: +66-2-955-0505
Vietnam – Ho Chi Minh City
Phone: +84-8-8232-546/7
Fax: +84-8-8221-443
For Latin/South American
Countries not shown
Phone: +57-1-240-9396
Fax: +57-1-660-0206
Europe/Middle East/Africa
Austria – Vienna
Phone: +43-190-560-0
Fax: +43-190-560-1333
Belgium – Kessel-Lo
Phone: +32-16-352-300
Fax: +32-16-352-352
Bulgaria – Sofia
Phone: +359-2-971-2152
Fax: +359-2-971-2153
Czech Republic – Kurim
Phone: +420-5-41-162-111
Fax: +420-5-41-162-223
Denmark – Viby J
Phone: +45-70-15-52-00
Fax: +45-86-29-51-33
Egypt – Cairo
Phone: +20-2-417-76-47
Fax: +20-2-419-23-34
Estonia – Tallinn
Phone: +372-65-05-474
Fax: +372-65-05-470
Finland – Helsinki
Phone: +358-95-12-34-20
Fax: +358-95-12-34-250
France
Cergy-Pontoise
Phone: +33-1-3420-8888
Fax: +33-1-3420-8600
Product Information Center:
(Technical Support)
Phone: +33-1-3420-8943
Fax: +33-1-3420-8623
France
Tyco Electronics Export
St Ouen L’Aumone
Phone: +33-1-3440-7200
Fax: +33-1-3440-7220 or
+33-1-3440-7230
Germany – Bensheim
Phone: +49-6251-133-0
Fax: +49-6251-133-1600
Product Information Center:
(Technical Support)
Phone: +49-6251-133-1999
Fax: +49-6251-133-1988
Germany – Langen
Phone: +49-6103-709-0
Fax: +49-6103-709-1223
Germany – Speyer
Phone: +49-6232-30-0
Fax: +49-6232-30-2243
Germany
HTS Division – Neunkirchen
Phone: +49-2247-305-0
Fax: +49-2247-305-122
Great Britain
Stanmore Middlesex
Phone: +44-181-954-2356
Fax: +44-181-954-6234
Product Information Center:
(Technical Support)
Freephone GB: 0800-267-666
Phone: +44-141 810 8967…69
Fax: +44-141 810 8971
Great Britain – Dorcan, Swindon
Raychem Products
Phone: +44-1793-528171
Fax: +44-1793-572516
Greece – Athens
Phone: +30-1-9370-396/397
Fax: +30-1-9370-655
Hungary – Budapest
Phone: +36-1-289-1000
Fax: +36-1-289-1010
Ireland – Dublin
Phone: +353-1-820-3000
Fax: +353-1-820-9790
Israel – Yokneam
Phone: +972-4-959-0508
Fax: +972-4-959-0506
Italy – Collegno (Torino)
Phone: +39-011-4012-111
Fax: +39-011-4031-116
Lithuania – Vilnius
Phone: +370-5-21-31-402
Fax: +370-5-21-31-403
Netherlands – ’s-Hertogenbosch
Phone: +31-73-6246-246
Fax: +31-73-6212-365
Product Information Center:
(Technical Support)
Phone: +31-73-6246-999
Fax: +31-73-6246-998
Norway – Nesbru
Phone: +47-66-77-88-99
Fax: +47-66-77-88-55
Poland – Warsaw
Phone: +48-22-5490-888
Fax: +48-22-5490-880
Romania – Bucharest
Phone: +40-1-311-3479+3596
Fax: +40-1-312-0574
Russia – Moscow
Phone: +7-095-926-55-06…09
Fax: +7-095-926-55-05
Russia – St. Petersburg
Phone: +7-812-325-30-83
Fax: +7-812-325-32-88
Scotland – Dundee
Madison Cable Products
Phone: +44-1382-508080
Fax: +44-1382-505060
Slovakia – Banská Bystrica
Phone: +421-48-415-20-11/12
Fax: +421-48-415-20-13
Slovenia – Ljubljana
Phone: +386-1561-3270
Fax: +386-1561-3240
South Africa – Port Elizabeth
Phone: +27-41-405-4500
Fax: +27-41-486-1314
Spain – Barcelona
Phone: +34-93-291-0330
Fax: +34-93-201-7879
Product Information Center:
(Technical Support):
Phone: +34-93-291-0330
Fax: +34-93-200-3779
Sweden – Upplands Väsby
Phone: +46-8-50-72-50-00
Fax: +46-8-50-72-50-01
Switzerland – Steinach
Phone: +41-71-447-0447
Fax: +41-71-447-0444
Turkey – Istanbul
Phone: +90-212-281-8181…3
+90-212-282-5130/5430
Fax: +90-212-281-8184
Ukraine – Kiev
Phone: +38-044-238-6908
Fax: +38-044-568-5740
203
TYCO ELECTRONICS CORPORATION
WWW.TYCOELECTRONICS.COM