BLE112 DATA SHEET Thursday, 23 May 2013 Version 1.4 Copyright (c) 2000-2013 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga's products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy VERSION HISTORY Version Comment 1.0 Certification information updated. Layout guide for BLE112-N added. 1.1 RF pin dimensions added 1.11 Absolute maximum supply corrected 1.2 Certification information updated 1.21 Current consumption added 1.22 Current consumption profiles added 1.23 Typo corrected on table 2 1.24 UART chapter, I/O Ports chapter, DC characteristics 1.25 Updated product codes 1.26 Note about P1_0 and P1_1 in chapter 2.1 1.27 Design check list, peripheral pull-up/pull-down requirements 1.28 Updating "Alternate" configuration table for clarity 1.29 Absolute maximum ratings: all supply nets must have the same voltage. Opamp and comparator removed from the peripherals table. 1.3 MIC Japan information updated 1.4 Updated contact information Bluegiga Technologies Oy TABLE OF CONTENTS 1 BLE112 Product numbering ..........................................................................................................................6 2 Pinout and Terminal Description ...................................................................................................................7 2.1 I/O Ports .................................................................................................................................................9 2.2 UART ......................................................................................................................................................9 2.3 Electrical Characteristics ..................................................................................................................... 10 2.4 Absolute Maximum Ratings ................................................................................................................ 10 2.5 Recommended Operating Conditions ................................................................................................. 10 2.6 DC Characteristics .............................................................................................................................. 10 2.7 Current Consumption .......................................................................................................................... 11 2.8 Antenna characteristics ....................................................................................................................... 11 3 Physical Dimensions .................................................................................................................................. 14 4 Power-On Reset and Brownout Detector ................................................................................................... 16 5 Design Guidelines ...................................................................................................................................... 17 5.1 General Design Guidelines ................................................................................................................. 17 5.2 Layout Guide Lines ............................................................................................................................. 18 5.3 BLE112-A Layout Guide ..................................................................................................................... 18 5.4 BLE112-N Layout Guide ..................................................................................................................... 19 5.5 Design Check List ............................................................................................................................... 20 6 Soldering Recommendations ..................................................................................................................... 21 7 Block diagram ............................................................................................................................................. 22 8 Certifications ............................................................................................................................................... 25 8.1 Bluetooth ............................................................................................................................................. 25 8.2 FCC and IC ......................................................................................................................................... 25 8.2.1 9 FCC et IC ..................................................................................................................................... 26 8.3 CE ....................................................................................................................................................... 28 8.4 MIC Japan ........................................................................................................................................... 28 8.5 KCC (Korea) ........................................................................................................................................ 28 8.6 Qualified Antenna Types for BLE112-E and BLE112-N ..................................................................... 28 Contact Information .................................................................................................................................... 30 Bluegiga Technologies Oy BLE112 Bluetooth(R) low energy single mode module DESCRIPTION BLE112, Bluetooth low energy single mode module is a single mode device targeted for low power sensors and accessories. BLE112 offers all Bluetooth low energy features: radio, stack, profiles and application space for customer applications, so no external processor is needed. The module also provides flexible hardware interfaces to connect sensors, simple user interfaces or even displays directly to the module. BLE112 can be powered directly with a standard 3V coin cell batteries or pair of AAA batteries. In lowest power sleep mode it consumes only 400nA and will wake up in few hundred microseconds. APPLICATIONS: KEY FEATURES: Heart rate sensors Pedometers Watches Blood pressure and glucose meters Bluetooth v.4.0, single mode compliant o Supports master and slave modes o 4+ simultaneous connection in master mode Integrated Bluetooth low energy stack o GAP, GATT, L2CAP, SMP o Bluetooth low energy profiles Radio performance o TX power: +3dBm to -23dBm o RX sensitivity: -85dBm to 91dBm Ultra low current consumption o Transmit: 27mA (0dBm) o Sleep mode 3: 0.4uA Programmable 8051 processor for embedding full applications Weight scales Bluetooth qualified Key fobs CE qualified Households devices Modular certification for FCC, IC and KCC Security tags Wireless keys (keyless go) MIC Japan compatibility fully tested with ARIB STD-T66 Proximity sensors HID keyboards and mice Indoor GPS broadcasting devices sensors and collector Bluegiga Technologies Oy 1 BLE112 Product numbering Antenna: A = Internal E = External N = RF pin BLE112-A-X Firmware revision Available products and product codes Product code Description BLE112-A-v1 BLE112 with integrated chip antenna and software version 1.0 BLE112 with RF pin and software version 1.0 BLE112-N-v1 Non-standard product, so a minimum order quantity applies. Please contact: sales@bluegiga.com BLE112 with U.FL connector and software version 1.0 BLE112-E-v1 Non-standard product, so minimum order quantity applies. Please contact: sales@bluegiga.com Bluegiga Technologies Oy Page 6 of 31 1 GND 2 AVDD RF 31 Pinout and Terminal Description RFGND 32 2 3 AVDD 4 P2_2 5 P2_1 GND 30 6 P2_0 7 P1_7 RESET 29 P0_0 28 8 P1_6 P0_1 27 9 VDD_USB P0_2 26 21 GND 20 DVDD P0_6 22 19 P0_7 P0_5 23 13 P1_5 18 P1_0 12 USB- 17 P1_1 P0_4 24 16 P1_2 11 USB+ 15 P1_3 P0_3 25 14 P1_4 10 GND Figure 1: BLE112 RESET PIN NUMBER 29 PAD TYPE Active low reset. 1, 10, 21, 30 GND RF 31 RF (* RFGND 32 GND DVDD AVDD VDD_USB 20 2, 3 9 Supply voltage Supply voltage Supply voltage GND DESCRIPTION GND RF output/input for BLE112-N. With BLE112-A and BLE112-E do not connect. RF ground. Connected to GND internally in the module. With BLE112-A and BLE112-E leave floating or connect to a solid GND plane. Supply voltage 2V - 3.6V Supply voltage 2V - 3.6V Supply voltage 2V - 3.6V *) RF pin is not connected in BLE112-A and BLE112-E. To use RF pin with BLE112-B please see the design guide. Table 1: Supply and RF Terminal Descriptions Bluegiga Technologies Oy Page 7 of 31 PIN PIN NAME PIN TYPE NUMBER DESCRIPTION 4 P2_2 Digital I/O Configurable I/O port, See table 3 5 P2_1 Digital I/O Configurable I/O port, See table 3 6 7 8 11 12 13 14 15 16 P2_0 P1_7 P1_6 USB+ USBP1_5 P1_4 P1_3 P1_2 Digital Digital Digital USB+ USBDigital Digital Digital Digital 17 P1_1 Digital I/O 18 P1_0 Digital I/O 19 22 23 24 25 26 27 28 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 Digital Digital Digital Digital Digital Digital Digital Digital Configurable I/O Configurable I/O Configurable I/O USB data plus USB data minus Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O table 3 Configurable I/O table 3 Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port with 20mA driving capability, See port with 20mA driving capability, See port, port, port, port, port, port, port, port, See See See See See See See See table table table table table table table table 3 3 3 3 3 3 3 3 Table 2: Terminal Descriptions *) BLE112 is configurable as either SPI master or SPI slave PERIPHERAL / FUNCTION ADC USART 0 SPI USART 0 UART USART 1 SPI USART 1 UART TIMER 1 TIMER 3 TIMER 4 Alt. 1 Alt.2 Alt. 1 Alt.2 Alt. 1 Alt.2 Alt. 1 Alt.2 Alt. 1 Alt.2 Alt. 1 Alt.2 Alt. 1 Alt.2 P0 P1 7 6 5 4 3 2 1 0 A7 A6 A5 A4 A3 A2 A1 A0 C SS MO MI 7 6 5 4 3 2 MO MI C SS 1 0 1 2 1 0 2 P2 1 0 RT CT TX RX TX RX RT CT MI MO C SS MI MO C SS RX TX RT CT RX TX RT CT 3 4 4 3 2 1 0 0 1 1 0 0 0 DC DD DEBUG OBSSEL 5 4 3 2 1 0 Table 3:Peripheral I/O Pin Mapping Bluegiga Technologies Oy Page 8 of 31 2.1 I/O Ports Each I/O port, except pins P1_0 and P1_1, can be configured as an input with either internal pull-up or pulldown, or tri-state. Pull-down or pull-up can only be configured to whole port, not individual pins. Unused I/O pins should have defined level and not be floating. To avoid excessive leakage current P1_0 and P1_1 must be configured either as outputs or as inputs using external pull-up or pull-down resistors. See the Profile Toolkit developer guide for more information about the configuration. During reset the I/O pins are configured as inputs with pull-ups. P1_0 and P1_1 are inputs but do not have pull-up or pull-down. The pins configured as peripheral I/O signals do not have pull-up/pull-down capability, even if the peripheral function is an input. In power modes PM1, PM2, and PM3, the I/O pins retain the I/O mode and output value (if applicable) that was set when PM1/PM2/PM3 was entered. All the IO's set as input must have an external pull-up or pull-down resistor to avoid excessive leakage current. 2.2 UART UART baud rate can be configured up 2 Mbps. See the Profile Toolkit developer guide for more information. Following table lists commonly used baud rates for BLE112 Baud rate (bps) Error (%) 2400 0.14 4800 0.14 9600 0.14 14 400 0.03 19 200 0.14 28 800 0.03 38 400 0.14 57 600 0.03 76 800 0.14 115 200 0.03 230 400 0.03 Table 4: Commonly used baud rates for BLE112 Bluegiga Technologies Oy Page 9 of 31 2.3 Electrical Characteristics 2.4 Absolute Maximum Ratings Note: These are absolute maximum ratings beyond which the module can be permanently damaged. These are not maximum operating conditions. The maximum recommended operating conditions are in the table 6. Rating Storage Temperature Min -40 Max 85 Unit C AVDD,DVDD, VDD_USB (* -0.3 3.9 V VSS-0.4 VDD+0.4 V Max 85 3.6 Unit C V Other Terminal Voltages *) All supply nets must have the same voltage Table 5: Absolute Maximum Ratings 2.5 Recommended Operating Conditions Rating Operating Temperature Range AVDD, DVDD, VDD_USB (* Min -40 2.0 *) Supply voltage noise should be less than 10mVpp. Excessive noise at the supply voltage will reduce the RF performance. Table 6: Recommended Operating Conditions 2.6 DC Characteristics Parameter Logic-0 input voltage Logic-1 input voltage Logic-0 input current Logic-1 input current I/O pin pull-up and pull-down resistors Logic-0 output volatge, 4 mA pins Logic-1 output voltage, 4 mA pins Test Conditions Min Input equals 0V Input equals VDD 2.5 -50 -50 Typ Max Unit 0.5 V V nA nA k V V 50 50 20 Output load 4 mA Outoput load 4 mA 0.5 2.4 For detailed I/O terminal characteristic and timings refer to the CC2540 datasheet available in (http://www.ti.com/lit/ds/symlink/cc2540.pdf) Bluegiga Technologies Oy Page 10 of 31 2.7 Current Consumption Power mode Active mode TX 2 dBm Active mode TX -2 dBm Active mode TX -6 dBm Active mode RX Power mode 1 Power mode 2 Power mode 3 Min Typ Max 36 30 28 25 Unit mA mA mA mA uA uA uA 235 0.9 0.4 Table 7: Current consumption of BLE112 36 mA 25 mA 0.9 uA (Power mode 2) 7.6 mA 7.6 mA 0.9uA (Power mode 2) 500 us 3.8 ms Figure 2: Typical current consumption profile during advertising in slave mode 36 mA 25 mA 7.6 mA 0.9 uA (Power mode 2) 7.6 mA 0.9 uA (Power mode 2) 500 us Figure 3: Typical current consumption profile during data connection in slave mode 2.8 Antenna characteristics The antenna radiation pattern is depends on the mother board layout. Following characteristics are measured from a test board based on the layout guide given in chapter 4. Efficiency 33% (-4.8 dB) Bluegiga Technologies Oy Page 11 of 31 Peak gain 0 dBi Figure 4: Radiation pattern of BLE112, top view Figure 5: Radiation pattern of BLE112, front view Bluegiga Technologies Oy Page 12 of 31 Figure 6: Radiation pattern of BLE112, side view Bluegiga Technologies Oy Page 13 of 31 3 Physical Dimensions Figure 7: Physical dimensions and pinout (top view) Figure 8: Dimensions for the RF pin Bluegiga Technologies Oy Page 14 of 31 12.05 mm Antenna 18.10 mm U.fl Figure 9: Physical dimensions (top view) 2.3 mm 2.1 mm 18.1 mm Figure 10: Physical dimensions (side view) Figure 11: Recommended land pattern for BLE112-A and BLE112-E Bluegiga Technologies Oy Page 15 of 31 4 Power-On Reset and Brownout Detector BLE112 includes a power-on reset (POR), providing correct initialization during device power on. It also includes a brownout detector (BOD) operating on the regulated 1.8-V digital power supply only. The BOD protects the memory contents during supply voltage variations which cause the regulated 1.8-V power to drop below the minimum level required by digital logic, flash memory, and SRAM. When power is initially applied, the POR and BOD hold the device in the reset state until the supply voltage rises above the power-on-reset and brownout voltages. Bluegiga Technologies Oy Page 16 of 31 5 Design Guidelines 5.1 General Design Guidelines BLE112 can be used directly with a coin cell battery. Due to relatively high internal resistance of a coin cell battery it is recommended to place a 100uF capacitor in parallel with the battery. The internal resistance of a coin cell battery is initially 5in the range of 10 ohms but the resistance increases rapidly as the capacity is1 used. 6 4 3 2 Basically the higher the value of the capacitor the higher is the effective capacity of the battery and thus the longer the life time for the application. The minimum value for the capacitor depends on the end application and the maximum transmit power used. The leakage current of a 100uF capacitor is in the range of 0.5 uA to 3 uA and generally ceramic capacitors have lower leakage current than tantalum or aluminum electrolytic capacitors. REVISION RECORD L TR D ECO NO: APPROVED: DATE: D Optionally TI's TPS62730 can be used to reduce the current consumption during TX/RX and data processing stages. TPS62730 is an ultra low power DC/DC converter with by-pass mode and will reduce the current consumption during transmission nominally by ~20% when using 3V coin cell battery. A ferrite bead is recommended to be used to filter any excessive noise in the power supply lines to guarantee the radio performance. C C OPTIONAL DC/DC VBAT 2 V...3 V3 _ SW MOD2 6 VIN 2 .2 u F/1 0 V/X5 R TPS62730 GN D ON/BYP P1 _ 7 /DCDC 6 P2 _ 2 P2 _ 1 C3 STAT 1 1 u F/1 6 V/X5 R C1 1 BLE112-A 1 2 3 4 5 6 7 8 9 10 11 12 13 2 4 5 C1 5 1 0 0 u F/6 .3 V/X5 R 4 2 .2 H 2 0 % , 1 3 0 m A, 0 .4 3 o h m SW VOUT C1 0 L1 5 U5 3 P1 _ 7 /DCDC 2 .2 u F/1 0 V/X5 R 1 GND AVDD AVDD P2_2 P2_1 P2_0 P1_7 P1_6 DVDD_USB GND USB+ USBP1_5 1 P2 _ 2 GND RESET P0_0 P0_1 P0_2 P0_3 P0_4 P0_5 P0_6 30 29 28 27 26 25 24 23 22 1 2 4 5 6 P2 _ 1 REVI SI O N RECO RD LTR ECO NO : APPRO VED: 910 HEADER_ 2 X5 _ SM D_ 1 .2 7 M M PROGRAMMING INTERFACE 14 15 16 17 18 19 20 21 1 u F/1 6 V/X5 R 2 3 78 RESET_ N RESET_ N P1_4 P1_3 P1_2 P1_1 P1_0 P0:7 D VD D GN D C6 U4 BATTERYHOLDER_SMD_CR2032 J1 3 2 D C5 1 u F/1 6 V/X5 R B B Figure 12: Example schematic for BLE112 with a coin cell battery MCP1700T- 3302E/ T CO N- MI NI USB- SO CKET- SMD P1 L4 FB 1kohm 2 C 32 2. 2uF/ 10V / X 5R VO UT GN D VI N 1 C 31 3 2. 2uF/ 10V / X 5R 1 2 3 4 5 0. 47uF/ 6. 3V / X 5R 9 8 7 6 C VBUS DD+ NC G ND C 20 J10 MO D3 C7 1uF/ 16V/ X5R A DRAWN:DATED: C9 BLE112- A G ND AVDD AVDD P2_2 P2_1 P2_0 P1_7 P1_6 DVDD_USB G ND USB+ PR USB-A P1_5 COM PANY: 30 G ND 29 RESET 28 P0_0 27 P0_1 26 P0_2 25 P0_3 24 P0_4 23 1 2 .0 4 .2 0 1 1 P0_5 22 P0_6 A RESET TITL E: BLE112 Evaluation Board P 1_4 P 1_3 P 1_2 P 1_1 P 1_0 P 0: 7 DV DD GN D 1uF/ 16V/ X5R 1 2 3 4 5 6 7 8 9 10 11 12 13 CHECKED: DATED: CODE: - 14 15 16 17 18 19 20 21 QUAL ITY CONTROL :DATED: REL EASED: SIZE: DRAWING NO: -C1.0 REV: - DATED: C8 SCAL E: SHEET: 1OF3 2 1uF/ 16V/ X5R R15 1 1. 5K, 50V, 0. 063W B R13 1 2 33R, 50V, 0. 063W R14 1 2 33R, 50V, 0. 063W C127 47pF/ 50V/ C0G C128 47pF/ 50V/ C0G Figure 13: Example schematic for BLE112 with USB CO MPANY: A TI TLE: BLE112 Evaluation Board DRAWN: DATED: P RA CHECKED: 12.04.2011 DATED: CO DE: -- Bluegiga Technologies Oy Q UALI TY CO NTRO L: DATED: RELEASED: - SI ZE: DRAWI NG NO : C-1.0 DATED: SCALE: Page 17 of 31 SHEET: 23 O F * path for the return current is cut MIC input - Place LC filtering and DC coupling capacitors symmetrically as close to pins as possible -5.2 Place biasing LayoutMIC Guide Lines resistors symmetrically as close to microhone as pos -Use Make sure that the bias trace does not cross separated GND regions (D good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces. If using vias current separated byis max 3 mmIftothis avoid is emission AGND) so overlapping that theground pathplanes for use thestitching return cut. not possibl from the edges of the PCB. Connect all the GND pins directly to a solid GND plane and make sure that there notimpedance separate GND regions but keep one solidtraces GND plane. is a low path for the return current following the signal and supply all the way from start to the end. -A good Keep the trace as short as possible practice is to dedicate one of the inner layers to a solid GND plane and one of the inner layers to supply voltage planes and traces and route all the signals on top and bottom layers of the PCB. This arrangement will make sure that any return current follows the forward current as close as possible and any loops are minimized. Recommended PCB layer configuration Signals GND Power Signals Figure 14: Typical 4-layer PCB construction Overlapping GND layers without GND stitching vias Overlapping GND layers with GND stitching vias shielding the RF energy Figure 15: Use of stitching vias to avoid emissions from the edges of the PCB 5.3 BLE112-A Layout Guide For optimal performance of the antenna place the module at the corner of the PCB as shown in the figure 16. Do not place any metal (traces, components, battery etc.) within the clearance area of the antenna. Connect all the GND pins directly to a solid GND plane. Place the GND vias as close to the GND pins as possible. Use good layout practices to avoid any excessive noise coupling to signal lines or supply voltage lines. Avoid placing plastic or any other dielectric material closer than 5 mm from the antenna. Any dielectric closer than 5 mm from the antenna will detune the antenna to lower frequencies. Bluegiga Technologies Oy Page 18 of 31 T Figure 16: Recommended layout for BLE112-A 5.4 BLE112-N Layout Guide Use 50 ohm transmission line to trace the signal from RF pin to an external RF connector. Figure 17 shows a layout example for BLE112-N with an external SMA connector. Board edge GND contact for the RF trace 50 ohm trace GND stitching vias separated by max 3 mm SMA connector Figure 17: Example layout for BLE112-N Bluegiga Technologies Oy Page 19 of 31 A transmission line impedance calculator, such as TX-Line made by AWR, can be used to approximate the dimensions for the 50 ohm transmission line. Figure 18 shows an example for two different 50 ohm transmission lines. CPW Ground W = 0.15 mm G = 0.25 mm RF GROUND Prepreg, r = 3.7 RF GROUND h = 0.076 mm RF GROUND FR4, r = 4.6 GND stitching vias MICROSTRIP W = 1.8 mm FR4, r = 4.6 h = 1 mm RF GROUND Figure 18: Example cross section of two different 50 ohm transmission line 5.5 Design Check List Antenna is placed at the edge of a PCB, preferably to a corner Antenna has sufficient clearance area around it and it is not covered by metal All the GND pins are connected to a solid GND plane All the IOs are in a known state and there are no leakage paths from the IOs o UART and SPI inputs must have external pull-up or pull-down o P1_0 and P1_1 must have either external pull-up or pull-down or configured as output TX power is set not higher than required for each application By-pass capacitor (47 uF... 100uF) is placed parallel with a coin cell battery to compensate the high series resistance of a coin cell Current test point is placed to measure the sleep current Bluegiga Technologies Oy Page 20 of 31 6 Soldering Recommendations BLE112 is compatible with industrial standard reflow profile for Pb-free solders. The reflow profile used is dependent on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and particular type of solder paste used. Consult the datasheet of particular solder paste for profile configurations. Bluegiga Technologies will give following recommendations for soldering the module to ensure reliable solder joint and operation of the module after soldering. Since the profile used is process and layout dependent, the optimum profile should be studied case by case. Thus following recommendation should be taken as a starting point guide. - Refer to technical documentations of particular solder paste for profile configurations - Avoid using more than one flow. - Reliability of the solder joint and self-alignment of the component are dependent on the solder volume. Minimum of 150m stencil thickness is recommended. - Aperture size of the stencil should be 1:1 with the pad size. - A low residue, "no clean" solder paste should be used due to low mounted height of the component. Bluegiga Technologies Oy Page 21 of 31 7 Block diagram BLE112 is based on TI's CC2540 chip. Embedded 32 MHz and 32.678 kHz crystals are used for clock generation. Matched balun and low pass filter provide optimal radio performance with extremely low spurious emissions. Small ceramic chip antenna gives good radiation efficiency even when the module is used in layouts with very limited space. 32 MHz XTAL 32.768 kHz XTAL Clock 2V - 3.6V Reset Voltage regulator CC2540 Reset Debug interface Power-on reset SRAM 8051 CPU core and memory arbitrator Flash Analog comparator I/O controller I/O IRQ controller DMA OPAMP Radio arbiter Radio registers Link layer engine SRAM ADC Demodulator Synth Modulator USB USART 0 USART 1 TIMER 1 Receive Frequency synthetisizer Transmit TIMER 2 TIMER 3 Balun + LPF TIMER 4 Ant Figure 19: Simplified block diagram of BLE112 CPU and Memory The 8051 CPU core is a single-cycle 8051-compatible core. It has three different memory access buses (SFR, DATA, and CODE/XDATA), a debug interface, and an 18-input extended interrupt unit. The memory arbiter is at the heart of the system, as it connects the CPU and DMA controller with the physical memories and all peripherals through the SFR bus. The memory arbiter has four memory-access points, access of which can map to one of three physical memories: an SRAM, flash memory, and XREG/SFR registers. It is responsible for performing arbitration and sequencing between simultaneous memory accesses to the same physical memory. The SFR bus is a common bus that connects all hardware peripherals to the memory arbiter. The SFR bus also provides access to the radio registers in the radio register bank, even though these are indeed mapped into XDATA memory space. Bluegiga Technologies Oy Page 22 of 31 The 8-KB SRAM maps to the DATA memory space and to parts of the XDATA memory spaces. The SRAM is an ultralow-power SRAM that retains its contents even when the digital part is powered off (power modes 2 and 3). The 128/256 KB flash block provides in-circuit programmable non-volatile program memory for the device, and maps into the CODE and XDATA memory spaces. Peripherals Writing to the flash block is performed through a flash controller that allows page-wise erasure and 4-bytewise programming. A versatile five-channel DMA controller is available in the system, accesses memory using the XDATA memory space, and thus has access to all physical memories. Each channel (trigger, priority, transfer mode, addressing mode, source and destination pointers, and transfer count) is configured with DMA descriptors that can be located anywhere in memory. Many of the hardware peripherals (AES core, flash controller, USARTs, timers, ADC interface, etc.) can be used with the DMA controller for efficient operation by performing data transfers between a single SFR or XREG address and flash/SRAM. Each CC2540 contains a unique 48-bit IEEE address that can be used as the public device address for a Bluetooth device. Designers are free to use this address, or provide their own, as described in the Bluetooth specification. The interrupt controller services a total of 18 interrupt sources, divided into six interrupt groups, each of which is associated with one of four interrupt priorities. I/O and sleep timer interrupt requests are serviced even if the device is in a sleep mode (power modes 1 and 2) by bringing the CC2540 back to the active mode. The debug interface implements a proprietary two-wire serial interface that is used for in-circuit debugging. Through this debug interface, it is possible to erase or program the entire flash memory, control which oscillators are enabled, stop and start execution of the user program, execute instructions on the 8051 core, set code breakpoints, and single-step through instructions in the code. Using these techniques, it is possible to perform in-circuit debugging and external flash programming elegantly. The I/O controller is responsible for all general-purpose I/O pins. The CPU can configure whether peripheral modules control certain pins or whether they are under software control, and if so, whether each pin is configured as an input or output and if a pullup or pulldown resistor in the pad is connected. Each peripheral that connects to the I/O pins can choose between two different I/O pin locations to ensure flexibility in various applications. The sleep timer is an ultra low power timer that uses an external 32.768-kHz crystal oscillator. The sleep timer runs continuously in all operating modes except power mode 3. Typical applications of this timer are as a realtime counter or as a wake-up timer to exit power modes 1 or 2. A built-in watchdog timer allows the CC2540 to reset itself if the firmware hangs. When enabled by software, the watchdog timer must be cleared periodically; otherwise, it resets the device when it times out. Timer 1 is a 16-bit timer with timer/counter/PWM functionality. It has a programmable prescaler, a 16-bit period value, and five individually programmable counter/capture channels, each with a 16-bit compare value. Each of the counter/capture channels can be used as a PWM output or to capture the timing of edges on input signals. It can also be configured in IR generation mode, where it counts timer 3 periods and the output is ANDed with the output of timer 3 to generate modulated consumer IR signals with minimal CPU interaction. Timer 2 is a 40-bit timer used by the Bluetooth low energy stack. It has a 16-bit counter with a configurable timer period and a 24-bit overflow counter that can be used to keep track of the number of periods that have transpired. A 40-bit capture register is also used to record the exact time at which a start-of-frame delimiter is received/transmitted or the exact time at which transmission ends. There are two 16-bit timer-compare registers and two 24-bit overflow-compare registers that can be used to give exact timing for start of RX or TX to the radio or general interrupts. Timer 3 and timer 4 are 8-bit timers with timer/counter/PWM functionality. They have a programmable prescaler, an 8-bit period value, and one programmable counter channel with an 8-bit compare value. Each of the counter channels can be used as PWM output. Bluegiga Technologies Oy Page 23 of 31 USART 0 and USART 1 are each configurable as either an SPI master/slave or a UART. They provide double buffering on both RX and TX and hardware flow control and are thus well suited to high-throughput full-duplex applications. Each USART has its own high-precision baud-rate generator, thus leaving the ordinary timers free for other uses. When configured as SPI slaves, the USARTs sample the input signal using SCK directly instead of using some oversampling scheme, and are thus well-suited for high data rates. The AES encryption/decryption core allows the user to encrypt and decrypt data using the AES algorithm with 128-bit keys. The AES core also supports ECB, CBC, CFB, OFB, CTR, and CBC-MAC, as well as hardware support for CCM. The ADC supports 7 to 12 bits of resolution with a corresponding range of bandwidths from 30-kHz to 4-kHz, respectively. DC and audio conversions with up to eight input channels (I/O controller pins) are possible. The inputs can be selected as single-ended or differential. The reference voltage can be internal, AVDD, or a single-ended or differential external signal. The ADC also has a temperature-sensor input channel. The ADC can automate the process of periodic sampling or conversion over a sequence of channels. The operational amplifier is intended to provide front-end buffering and gain for the ADC. Both inputs as well as the output are available on pins, so the feedback network is fully customizable. A chopper-stabilized mode is available for applications that need good accuracy with high gain. The ultralow-power analog comparator enables applications to wake up from PM2 or PM3 based on an analog signal. Both inputs are brought out to pins; the reference voltage must be provided externally. The comparator output is connected to the I/O controller interrupt detector and can be treated by the MCU as a regular I/O pin interrupt. RF front end RF front end includes combined matched balun and low pass filter, and ceramic chip antenna with matching network. Optimal matching combined with effective low pass filter provides extremely low in-band spurious emissions and harmonics. Optionally as a module assembly variant RF can be traced either to an embedded u.fl connector or to the RF pin of the module. Bluegiga Technologies Oy Page 24 of 31 8 Certifications BLE112 is compliant to the following specifications. 8.1 Bluetooth BLE112 Bluetooth low energy module is Bluetooth qualified and listed as a controller subsystem and it is Bluetooth compliant to the following profiles of the core spec version v.4.0: RF PHY HCI LL The maximum antenna gain specified for BLE112 is 2.3 dBi. Bluetooth qualification is valid for any antenna with gain less than 2.3 dBi. 8.2 FCC and IC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Statements: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. If detachable antennas are used: This radio transmitter (identify the device by certification number, or model number ifCategory II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible Bluegiga Technologies Oy Page 25 of 31 gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. See table 8 for the approved antennas for BLE112. OEM Responsibilities to comply with FCC and Industry Canada Regulations The BLE112 module has been certified for integration into products only by OEM integrators under the following condition: The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. As long as the condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or colocation with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. End Product Labeling The BLE112 module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: "Contains Transmitter Module FCC ID: QOQBLE112" "Contains Transmitter Module IC: 5123A-BGTBLE112" or "Contains FCC ID: QOQBLE112 "Contains IC: 5123A-BGTBLE112" The OEM of the BLE112 module must only use the approved antenna(s) listed in table 8, which have been certified with this module. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. 8.2.1 FCC et IC Declaration d'IC : Ce dispositif est conforme aux normes RSS exemptes de licence d'Industrie Canada. Son fonctionnement est assujetti aux deux conditions suivantes : (1) ce dispositif ne doit pas provoquer de perturbation et (2) ce Bluegiga Technologies Oy Page 26 of 31 dispositif doit accepter toute perturbation, y compris les perturbations qui peuvent entrainer un fonctionnement non desire du dispositif. Selon les reglementations d'Industrie Canada, cet emetteur radio ne doit fonctionner qu'avec une antenne d'une typologie specifique et d'un gain maximum (ou inferieur) approuve pour l'emetteur par Industrie Canada. Pour reduire les eventuelles perturbations radioelectriques nuisibles a d'autres utilisateurs, le type d'antenne et son gain doivent etre choisis de maniere a ce que la puissance isotrope rayonnee equivalente (P.I.R.E.) n'excede pas les valeurs necessaires pour obtenir une communication convenable. Si des antennes amovibles sont utilisees : Cet emetteur radio (identifier le dispositif a l'aide de son numero de certification ou de son numero de modele s'il appartient a la Categorie II) a ete approuve par Industrie Canada pour fonctionner avec les types d'antenne enumeres ci-dessous, avec le gain admissible maximum et l'impedance d'antenne requise pour chaque type d'antenne indique. Les types d'antennes qui ne figurent pas dans cette liste ont un gain superieur au gain maximum indique pour ce type ; il est donc strictement defendu de les utiliser avec ce dispositif. Consulter le tableau 8 pour decouvrir les antennes approuvees pour BLE112. Responsabilites des OEM quant a la conformite avec les reglementations de FCC et d'Industrie Canada Le module BLE112 a ete certifie pour etre integre a des produits fabriques uniquement par les integrateurs OEM dans les conditions suivantes :Le module de l'emetteur ne doit pas etre situe pres d'une autre antenne ou d'un autre emetteur ni ou fonctionner conjointement avec ceux-ci. Dans la mesure ou cette condition est observee, il ne sera pas necessaire de soumettre l'emetteur a des essais supplementaires. Cependant, l'integrateur OEM est charge de tester son produit final pour s'assurer qu'il respecte toutes les autres exigences de conformite requises avec ce module installe (par exemple : emissions du dispositif numerique, exigences peripheriques de l'ordinateur, etc.). REMARQUE IMPORTANTE : En cas d'inobservance de ces conditions (en ce qui concerne certaines configurations ou l'emplacement du dispositif a proximite d'un autre emetteur), les autorisations de FCC et d'Industrie Canada ne seront plus considerees valables et l'identification de FCC et le numero de certification d'IC ne pourront pas etre utilises sur le produit final. Dans ces cas, l'integrateur OEM sera charge d'evaluer a nouveau le produit final (y compris l'emetteur) et d'obtenir une autorisation independante de FCC et d'Industrie Canada. Etiquetage du produit final Le module BLE112 est etiquete avec sa propre identification FCC et son propre numero de certification IC. Si l'identification FCC et le numero de certification IC ne sont pas visibles lorsque le module est installe a l'interieur d'un autre dispositif, la partie externe du dispositif dans lequel le module est installe devra egalement presenter une etiquette faisant reference au module inclus. Dans ce cas, le produit final devra etre etiquete sur une zone visible avec les informations suivantes : Contient module emetteur identification FCC : QOQBLE112 Contient module emetteur IC : 5123A-BGTBLE112 ou Contient identification FCC : QOQBLE112 Contient IC : 5123A-BGTBLE112 Bluegiga Technologies Oy Page 27 of 31 L'OEM du module BLE112 ne doit utiliser que la ou les antennes approuvees enumerees dans le tableau 8, qui ont ete certifiees avec ce module. Dans le guide d'utilisation du produit final, l'integrateur OEM doit s'abstenir de fournir des informations a l'utilisateur final portant sur les procedures a suivre pour installer ou retirer ce module RF ou pour changer les parametres RF. 8.3 CE BLE112 is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC). The product is conformity with the following standards and/or normative documents. EMC (immunity only) EN 301 489-17 V.1.3.3 in accordance with EN 301 489-1 V1.8.1 Radiated emissions EN 300 328 V1.7.1 Safety EN60950-1:2006+A11:2009+A1:2010+A12:2011 8.4 MIC Japan BLE112 has type approval with certification ID R 209- J00046 8.5 KCC (Korea) BLE112 is KCC certified with following certification numbers BLE112-A: KCC-CRM-BGT-BLE112-A BLE112-E: KCC-CRM-BGT-BLE112-E BLE112-N: KCC-CRM-BGT-BLE112-N 8.6 Qualified Antenna Types for BLE112-E and BLE112-N This device has been designed to operate with a standard 2.14 dBi dipole antenna. Any antenna of the same type and the same or less gain can be used without additional application to FCC. Table 8 lists approved antennas for BLE112. Any approved antenna listed in table 8 can be used directly with BLE112 without any additional approval. Any antenna not listed in table 8 can be used with BLE112 as long as detailed information from that particular antenna is provided to Bluegiga for approval. Specification of each antenna used with BLE112 will be filed by Bluegiga. Please, contact support@bluegiga.com for more information. Item 1 Manufacturer Pulse Manufacturers part number W1030 Measure d Gain (dBi) 1 Specifie d Gain (dBi) 2 dBi Measure Total Efficiency (%) 70 - 80 Bluegiga Technologies Oy Page 28 of 31 2 3 4 5 Linx Technologies Inc EAD Antenova Litecon ANT-2.4-CW-CT-SMA EA-79A B4844/B6090 CAR-ATR-187-001 1.3 0.4 1.4 0.8 2 dBi 2 dBi 2 dBi 2 dBi 77 60 76 - 82 60 - 70 Table 8: Approved Antennas For BLE112-E and BLE112-N Bluegiga Technologies Oy Page 29 of 31 9 Contact Information Sales: sales@bluegiga.com Technical support: support@bluegiga.com http://techforum.bluegiga.com Orders: orders@bluegiga.com WWW: www.bluegiga.com www.bluegiga.hk Head Office / Finland: Phone: +358-9-4355 060 Fax: +358-9-4355 0660 Sinikalliontie 5A 02630 ESPOO FINLAND Postal address / Finland: P.O. BOX 120 02631 ESPOO FINLAND Sales Office / USA: Phone: +1 770 291 2181 Fax: +1 770 291 2183 Bluegiga Technologies, Inc. 3235 Satellite Boulevard, Building 400, Suite 300 Duluth, GA, 30096, USA Sales Office / Hong-Kong: Phone: +852 3972 2186 Bluegiga Technologies Ltd. Unit 10-18 32/F, Tower 1, Millennium City 1 388 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Bluegiga Technologies Oy Page 30 of 31 Bluegiga Technologies Oy Page 31 of 31 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bluegiga Technologies: BLE112-E-v1 BLE112-A-v1