E M C C o m p o n e n t s May 2018 Chip beads For general signal line GHz noise countermeasure (general signal line, high-speed line) MMZ-E series MMZ1005-E MMZ1005-E 1005[0402 inch]* * Dimensions code JIS[EIA] type (2/10) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (3/10) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For general signal line GHz noise countermeasure (general signal line, high-speed line) Overview of MMZ1005-E type FEATURES Noise reduction solution for general signal line. Compared to the MMZ series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies with 1 element. Compared to the MMZ series, it can attain high impedance at GHz bands. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 1005 S LxWxT dimensions (mm) 1005 1.0x0.5x0.5 Material name S A D F 601 E Impedance () at 100MHz 601 600 102 1000 Characteristic type E T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Operating Storage Type temperature temperature C C MMZ1005-E -55 to +125 -55 to +125 The storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 10,000 mg 1 RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (4/10) E M C C o m p o n e n t s MMZ1005-E type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (5/10) E M C C o m p o n e n t s MMZ1005-E type MATERIAL CHARACTERISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. A material: This high-impedance product is based on the impedance frequency characteristics of our Y-material. The product offers excellent impedance characteristics, which is greater than 2500, in the vicinity of 100MHz range (MMZ1608A252B). D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (00MHz to 1GHz) for signal line applications. F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in the GHz range. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500 A 2000 D F 1500 1000 S 500 0 10 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (6/10) E M C C o m p o n e n t s MMZ1005-E type SHAPE & DIMENSIONS 0.50.05 0.50.05 10.05 0.1min. Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (7/10) E M C C o m p o n e n t s MMZ1005-E type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 600 1000 1800 600 1000 1500 1800 2200 120 220 47 75 120 180 220 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% [1GHz] ( ) 1000 1400 1800 1400 2000 2300 2700 3000 1000 1700 800 1500 2300 3200 5000 Tolerance 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% Measurement equipment Measurement item Product No. Impedance E4991A+16192A DC resistance Type-7556 Equivalent measurement equipment may be used. DC resistance Rated current Part No. ( )max. 0.65 1.00 1.50 0.80 1.20 1.60 2.10 2.20 0.70 1.00 0.70 1.00 1.50 1.60 2.30 (mA)max. 300 250 200 300 250 230 200 150 300 250 300 250 200 200 150 MMZ1005S601ET000 MMZ1005S102ET000 MMZ1005S182ET000 MMZ1005A601ET000 MMZ1005A102ET000 MMZ1005A152ET000 MMZ1005A182ET000 MMZ1005A222ET000 MMZ1005D121ET000 MMZ1005D221ET000 MMZ1005F470ET000 MMZ1005F750ET000 MMZ1005F121ET000 MMZ1005F181ET000 MMZ1005F221ET000 Manufacturer Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (8/10) E M C C o m p o n e n t s MMZ1005-E type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ1005S-E series MMZ1005A-E series MMZ1005A222E 4000 5000 Impedance () 1500 1000 500 3000 MMZ1005A102E 2500 2000 10 100 1000 Frequency (MHz) 10000 1200 1000 800 1500 600 1000 400 0 1 1400 MMZ1005A152E 200 500 MMZ1005S601E MMZ1005D221E 1600 MMZ1005A182E 3500 MMZ1005S102E 2000 1800 Impedance () MMZ1005S182E 2500 Impedance () 2000 4500 3000 0 MMZ1005D-E series MMZ1005A601E 1 10 100 1000 Frequency (MHz) MMZ1005D121E 10000 0 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F-E series 6000 MMZ1005F221E Impedance () 5000 MMZ1005F181E 4000 MMZ1005F121E 3000 MMZ1005F750E 2000 MMZ1005F470E 1000 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (9/10) E M C C o m p o n e n t s MMZ1005-E type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ1005S601ET000 MMZ1005S102ET000 Impedance () Z 600 R 400 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005A601ET000 100 1000 Frequency (MHz) R X 10000 10 100 1000 Frequency (MHz) 3500 3000 2500 2000 1500 1000 500 0 R X 10 100 1000 Frequency (MHz) X 500 0 10000 1 10 100 1000 Frequency (MHz) 4500 4000 3500 3000 2500 2000 1500 1000 500 0 Impedance () Z R 500 X 1 10 100 1000 Frequency (MHz) MMZ1005F121ET000 Impedance () 2500 2000 1500 Z 1000 R 500 1 X 10 100 1000 Frequency (MHz) 10000 1 10 100 1000 Frequency (MHz) 10000 R X 1 10 100 1000 Frequency (MHz) Z 2000 R 1500 1000 X 500 1 10 100 1000 Frequency (MHz) 10000 R 400 200 X 1 10 Z 600 R 400 200 X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F750ET000 Z 600 800 0 10000 800 4000 3500 3000 2500 2000 1500 1000 500 0 2500 1000 Z 100 1000 Frequency (MHz) 10000 MMZ1005F181ET000 3000 X 1200 1000 0 10000 500 MMZ1005D121ET000 1200 1000 R 1000 0 10000 MMZ1005F470ET000 1500 0 R MMZ1005A222ET000 Z 1 Z 1000 10000 Z 1500 MMZ1005A152ET000 Impedance () 1 2000 3000 1500 Impedance () Impedance () 10 2000 2000 Impedance () 1 2500 0 Impedance () Z MMZ1005D221ET000 Impedance () X 2500 MMZ1005A182ET000 0 R MMZ1005A102ET000 Impedance () Impedance () 1600 1400 1200 1000 800 600 400 200 0 Z Impedance () 200 0 3000 1800 1600 1400 1200 1000 800 600 400 200 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ1005F221ET000 6000 Impedance () Impedance () 800 Impedance () 1600 1400 1200 1000 800 600 400 200 0 1000 MMZ1005S182ET000 Z R 1 X 10 100 1000 Frequency (MHz) 10000 5000 4000 Z 3000 2000 1000 0 R 1 X 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm (10/10) E M C C o m p o n e n t s MMZ1005-E type PACKAGING STYLE REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B A 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MMZ1005-E 160min. Drawing direction A 0.650.1 Taping B 1.150.1 P1 2.00.05 K 0.8max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz1005-e_en.fm