Data Sheet ACDC-100 TRMS 1000A AC/DC Clamp-On Multimeter Where accuracy, quality, and the newest technology meet. The ACDC100 offers superior AC/DC measurement capabilities, highest product quality and enhanced ergonomics design. The TRMS version addresses needs of professionals who rely on performance and reliability. True RMS Backlight Capacitance AC/DC test voltage to 600V Resistance Continuuity No hassle warranty No waiting. No shipping charges. Our commitment to high-quality products and customer service is demonstrated by our industry exclusive "No Hassle" warranty. In the unlikely event that an Amprobe Test Tool requires warranty service, any of our local dealers are authorized to replace it, on the spot. Beeper Relative zero mode Auto power off Data hold MAX capture function for in rush current measurements (30 mS response) Large, easy to read digital display Diode Test Audible continuity Accommodates conductors up to 50mm (2.00") in diameter "Third hand" - test probe holder Rubber over-molded case with built-in probes storage Carrying case, test leads, batteries (installed) and user manual included (note: $500 MSLP limit) 600V Amprobe(R) Test Tools www.Amprobe.com Data Sheet 1000A ACDC-100 TRMS AC/DC Clamp-On Multimeter Electrical Specifications Accuracy is (% reading digits + number of digits) or otherwise specified, at 23 5 & less than 75% R.H. Function Range Accuracy DC Voltage 400.0 mV 0.3% + 3d 4.000V, 40.00V, 400.0V 0.5% + 3d 1.0% + 4d 600V NMRR : >50dB @ 50/60Hz CMRR : >120dB @ DC, 50/60Hz, Rs=1k Input Impedance : 10M, 30pF nominal (1000M for 400.0mV range) AC Voltage 50Hz ~ 500Hz 400.0mV 1) 4.0% + 4d 50Hz ~ 60Hz 4.000V, 40.00V, 400.0V 1.0% + 4d 60Hz ~ 500Hz 4.000V, 40.00V, 400.0V 1.5% + 4d 50Hz ~ 500Hz 600V 2.0% + 4d CMRR : >60dB @ DC to 60Hz, Rs=1k Input Impedance: 10M, 30pF nominal ACDC-100 TRMS Crest Factor: < 1.6 : 1 at full scale & < 3.2 : 1 at half scale 1) Selection by RANGE button manually, and is specified AC 60mV and up Resistance 400.0 0.8% + 6d 4.000k, 40.00k, 400.0k 0.6% + 4d 4.000M 1.0% + 4d 40.00M 2.0% + 4d Open Circuit Voltage : Audible Continuity Tester Open Circuit Voltage: Range: 400.0; Accuracy: Audible threshold: 0.4VDC typical 0.4VDC typical 1.5% + 6d between 10 and 120. Diode Tester Open Circuit Voltage Test Current (Typical) < 1.6 VDC 0.4mA Capacitance 500.0nF, 5.000F, 50.00F, 500.0F, 3000F 1) 3.5% + 6d2) 3) 1) Additional 50.00nF range accuracy is not specified 2) Accuracies with film capacitor or better Specified with battery voltage above 2.8V (approximately half full battery). Accuracy decreases gradually to 12% at low battery warning voltage of approximately 2.4V 3) DC Current (Clamp-on) 400.0A 0.0A ~ 400.0A 1.5% + 4d 1) 2) 1000A 400A ~ 800A 1.5% + 4d 1) 2) 800A ~ 900A 2.0% + 4d 1) 2) 900A ~ 1000A 5.0% + 30d 1) 2) 1) Induced error from adjacent current-carrying conductor: < 0.01A/A 2) Zero mode must be applied to zero the unit before measurement to ensure accuracy. This is particularly important below 20A. Amprobe(R) Test Tools www.Amprobe.com Data Sheet 1000A ACDC-100 TRMS AC/DC Clamp-On Multimeter Function Range Accuracy AC Current (Clamp-on) 400.0A 15Hz ~ 40Hz 2.0% + 5d 1) 2) 3) 40Hz ~ 200Hz 1.5% + 5d 1) 2) 4) 200Hz ~ 400Hz @ <50A 1.5% + 5d 1) 2) 400Hz ~ 1kHz @ <50A 4) 2.0% + 5d 1) 2) 800A 15Hz ~ 40Hz @ 400A ~ 600A 2.0% + 5d 1) 2) 3) 40Hz ~ 100Hz @ 400A ~ 600A 1.5% + 4d 1) 2) 15Hz ~ 60Hz @ 600A ~ 800A 5.0% + 30d 1) 2) 1) Induced error from adjacent current-carrying conductor: < 0.01A/A 2) ACDC-100 TRMS crest Factor: < 1.6 : 1 at full scale & < 3.2 : 1 at half scale 3) 4.0% + 5d for ACDC-100 TRMS 4) Accuracy is specified at <50A in this frequency bandwidth due to limited calibrator output capability for testing General Specifications Display: 3-3/4 digits 4000 counts LCD display Update Rate: 3 per second nominal Polarity: Automatic Low Battery: Below approx. 2.4V Operating Temperature: 0 to 40 Relative Humidity: Maximum relative humidity 80% for temperature up to 31 decreasing linearly to 50% relative humidity at 40 Altitude: Operating below 2000m Storage Temperature: -20 to 60, < 80% R.H. (with battery removed) Temperature Coefficient: nominal 0.15 x (specified accuracy)/ @(0 -18 or 28 -40), or otherwise specified Sensing: True RMS Safety: Meets EN61010-1:2001; IEC61010-2-032(2002), EN61010-2-032(2002), UL61010B-2-032(2003) Category III 600 Volts AC & DC. Transient protection: 6.5kV (1.2/50s surge) for all models Pollution degree: 2 E.M.C.: Meets EN61326-1 In an RF field of 3V/m: Capacitance function is not specified Other function ranges: Total Accuracy = Specified Accuracy + 45 digits Performance above 3V/m is not specified Overload Protections: Clamp-on jaws: DC 1000A or AC 800A rms continuous + & COM terminals (all functions) : 600VDC/VAC rms Power Supply: standard 1.5V AAA Size (NEDA 24G or IEC R03) battery X 2; or 1.5V AAA Size (NEDA 24A or IEC LR03) alkaline battery X 2 Power Consumption: typical 11mA for ACA/DCA and 2.9mA for other functions APO Timing: Idle for 30 minutes APO Consumption: typical 190A Dimension: L227mm X W78mm X H40mm Weight: 290 gm approx Jaw opening & Conductor diameter: 50mm max www.Amprobe.com 1000A ACDC-100 TRMS AC/DC Clamp-On Multimeter Data Sheet Included Accessories Test leads; carrying case SV-U; users manual Optional Accessories ELS2A Line splitter (Energizer) ACF-3000 AK 3000A AC Flexible Clamp-on Attachment TMA-K Single Input Thermocouple Temperature Attachment MTL-500 Test Lead Kit Test Lead Kit Replacement Accessories MTL-90B Test Leads w/Alligator Clips Available with TRMS and Display Backlight The ACDC-100 TRMS version addresses the needs of professionals who rely on performance and reliability. A large LCD for easy viewing. Simplified Interface These full function clamp-ons have simplified interfaces to help your customers get their work done quickly. Easy-to-read oversize display screens feature the large digits. Each meter offers auto and manual ranging along relative zero mode functions. Amprobe(R) Test Tools website: www.Amprobe.com email: info@amprobe.com Everett, WA 98203 Tel: 877-AMPROBE Amprobe(R) Test Tools Europe In den Engematten 14 79286 Glottertal, Germany Tel.: +49 (0) 7684 8009 - 0 (c)2007 Amprobe Test Tools. All rights reserved. 9/2007 3128767 Rev A Amprobe(R) Test Tools www.Amprobe.com