REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Added Arrhenius equation for unbiased bake under margin test
method A, back end margin test step C. Corrected military part
numbers for device types 01 and 02. Technical changes made to
1.2.2, table I, figure 1, figure 2, figure 4, figure 5, 4.3.1, and table II.
Added vendor CAGE 34649 for device type 05. Editorial changes
throughout.
89-01-19 M. A. Frye
B
Add device type 08 for vendor CAGE number 66579. Add vendor
CAGE number 34335 to the drawing as a source of supply for the 08
device with changes to table I. Deleted programming cycle timing
waveform and table III from drawing. Also deleted ESDS from
drawing. Editorial changes throughout.
89-10-30 M. A. Frye
C
Deleted vendor CAGE number 34335 as a source of supply for device
type 08. Added vendor CAGE number 34335 as a source of supply
for device types 01 through 07. Deleted figure 5. Editorial changes
throughout.
90-02-26 M. A. Frye
D
Changes in accordance with NOR 5962-R079-95. 95-02-15 M. A. Frye
E
Added provisions for QD certification. Added CAGE 0C7V7 to
drawing as a source of supply for device type 07. Updated boilerplate.
- glg
99-12-03 Raymond Monnin
F
Boilerplate update, part of 5 year review. ksr 06-09-29 Raymond Monnin
The original first page of this drawing has been replaced.
REV
SHEET
REV
SHEET
REV STATUS REV F F F F F F F F F F F
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11
PMIC N/A PREPARED BY
James E. Jamison
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Charles Reusing COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Michael A. Frye
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
87-10-23
MICROCIRCUIT, MEMORY, DIGITAL,
CMOS, 16K X 8-BIT ULTRA VIOLET
ERASABLE PROGRAMMABLE READ
ONLY MEMORY (UVEPROM),
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
F SIZE
A CAGE CODE
67268
5962-87661
SHEET
1 OF
11
DSCC FORM 2233
APR 97 5962-E646-06
.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87661 01 X A
Drawing number Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number 1/ Circuit function Access time
01 27C128 16K x 8-bit UVEPROM 90 ns
02 27C128 16K x 8-bit UVEPROM 120 ns
03 27C128 16K x 8-bit UVEPROM 150 ns
04 27C128 16K x 8-bit UVEPROM 170 ns
05 27C128 16K x 8-bit UVEPROM 200 ns
06 27C128 16K x 8-bit UVEPROM 250 ns
07 27C128 16K x 8-bit UVEPROM 300 ns
08 27C128 16K x 8-bit UVEPROM 70 ns
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
X GDIP1-T28 or CDIP2-T28 28 dual-in-line package 1/
Y CQCC1-N32 32 rectangular leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings. 2/
Supply voltage range (VCC) 2/..................................................... -0.6 V dc to 6.25 V dc
Supply voltage range (VPP) 2/..................................................... -0.6 V dc to 14.0 V dc
All input voltage range except A9 2/ .......................................... -0.6 V dc to 6.25 V dc
Input voltage range (A9) 2/.......................................................... -0.6 V dc to 13.5 V dc
Output voltage range 2/ .............................................................. -0.6 V dc to VCC + 1.0 V dc
Storage temperature range ........................................................ -65°C to +150°C
Power dissipation ........................................................................ 300 mW
Lead temperature (soldering, 10 seconds) .................................. +300°C
Thermal resistance, junction-to-case (θJC)................................... See MIL-STD-1835
Junction temperature (TJ) .......................................................... +150°C 3/
Data retention ............................................................................ 10 years minimum
1.4 Recommended operating conditions.
Supply voltage range (VCC) 4/ .................................................... 4.5 V dc to 5.5 V dc
Supply voltage range (VPP) 5/ ..................................................... 4.5 V dc to 5.5 V dc
High level input voltage range (VIH).............................................. 2.0 V dc to 6.5 V dc (TTL)
High level input voltage range (VIH).............................................. VCC -0.2 V dc to VCC +0.2 V dc (CMOS)
Low level input voltage range (VIL) ............................................. -0.1 V dc to 0.8 V dc (TTL)
Low level input voltage range (VIL) ............................................. GND -0.2 to GND +0.2 V dc (CMOS)
Case operating temperature range (TC) ...................................... -55°C to +125°C
1/ Lid shall be transparent to permit ultraviolet light erasure.
2/ Under absolute maximum ratings, voltages are with respect to GND.
3/ Maximum junction temperature may be increased to +175°C during burn-in and steady-state life.
4/ VCC must be applied before or at the same time as VPP and removed after or at the same time as VPP. The device must
not be inserted into or removed from the board when VPP or VCC is applied.
5/ VPP can be connected to VCC directly (except in the program mode). VCC supply current in this case would be ICC + IPP.
During programming, VPP must be maintained at 12.5 V (±0.5 V).
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.2 Truth table. The truth table shall be as specified on figure 2.
3.2.2.1 Unprogrammed devices. The truth table for unprogrammed devices shall be as specified on figure 2.
3.2.2.2 Programmed devices. The requirements for supplying programmed devices are not part of this drawing.
3.2.3 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test Symbol Conditions Device Group A Limits Unit
-55°C < TC < +125°C types subgroups
4.5 V < VCC < 5.5 V Min Max
unless otherwise specified
High level output VOH IOH = -400 µA All 1,2,3 2.4 V
voltage
Low level output VOL IOL = 2.1 mA All 1,2,3 0.45 V
voltage
Input current II VI = 0 V to 5.5 V All 1,2,3 ±10 µA
(leakage)
Output current IO VO = 0 V to VCC All 1,2,3 ±10 µA
(leakage)
VPP supply current IPP1 VPP = VCC = 5.5 V All 1,2,3 100 µA
VPP supply current IPP2 VPP = 13 V 01-07 1 50 mA
(during program
pulse) 1/ 08 60
Operating supply ICC1 VCC = 5.5 V, CE = VIL, 03.04, 1,2,3 25 mA
current (active) f = 1/tAVQV, 05,06,
01-08 = 0 mA 07
08 85
01 70
02 60
Standby power supply ICC2 VCC = 5.5 V, CE = 2.0 V, 01-07 1,2,3 3.0 mA
current (TTL) f = 0
08 200
Standby power supply ICC3 VCC = 5.5 V, CE = VCC, 01-07 1,2,3 300 µA
current (CMOS) f = 0
08 500
Input capactiance CIN VI = 0 V, f = 1 MHz, All 4 10 pF
see 4.3.1c
Output capacitance COUT VO = 0 V, f = 1 MHz, All 14 pF
see 4.3.1c 4
Functional tests see 4.3.1e All 7,8A,8B
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test Symbol Conditions Device Group A Limits Unit
-55°C < TC < +125°C types subgroups
4.5 V < VCC < 5.5 V Min Max
unless otherwise specified
Address access time tAVQV See figures 3 and 4 01 9,10,11 90 ns
2/ 02 120
03 150
04 170
05 200
06 250
07 300
08 70
Chip enable access tELQV See figures 3 and 4 01 9,10,11 90 ns
time 2/ 02 120
03 150
04 170
05 200
06 250
07 300
08 70
Output enable access tOLQV See figures 3 and 4 01,02 9,10,11 50 ns
time 2/ 03,04 70
05 75
06 100
07 120
08 25
CE or OE disable to tEHQZ, See figures 3 and 4 01,02 9,10,11 50 ns
output in high Z 1/ tOHQZ 03,04
05,06 60
07 105
08 25
CE or OE enable to tEHQV, See figures 3 and 4 All 9,10,11 0 ns
output valid 1/ tOHQV
1/ May not be tested, but shall be guaranteed to the limits specified in table I.
2/ For all switching characteristics and timing measurements, inputs pulse levels are 0.40 V and 2.4 V and
VPP = 12.5 V±0.5 V during programming.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
6
DSCC FORM 2234
APR 97
Device types ALL
Case Outlines X Y
Terminal Number Terminal Symbol
1 VPP NC
2 A12 V
PP
3 A7 A
12
4 A6 A
7
5 A5 A
6
6 A4 A
5
7 A3 A
4
8 A2 A
3
9 A1 A
2
10 A0 A
1
11 O1 A
0
12 O2 NC
13 O3 O
1
14 GND O2
15 O4 O
3
16 O5 GND
17 O6 NC
18 O7 O
4
19 O8 O
5
20 CE O6
21 A10 O
7
22 OE O8
23 A11 CE
24 A9 A
10
25 A8 OE
26 A13 NC
27 PGM A11
28 VCC A
9
29 --- A8
30 --- A13
31 --- PGM
32 --- VCC
NC = no connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
7
DSCC FORM 2234
APR 97
Mode Function pins (see note 1)
CE OE PGM VPP VCC A9 A0 01 - 08
Read VIL VIL VIH VCC VCC X X DOUT
Output disable VIL VIH VIH VCC VCC X X HIGH-Z
Standby VIH X X VCC VCC X X HIGH-Z
Programming VIL VIH VIL VPP VCC X X DIN
Verify VIL VIL VIH VPP VCC X X DOUT
Program VIH X X VPP VCC X X HIGH-Z
inhibit
Signature mode VIL VIL VIH VCC VCC VH VIL MFG code
(see notes 2,
3, and 4)
VH VIH Device code
NOTES:
1. X can be VIL or VIH.
2. VH = 12 V±0.5 V.
3. All other address must be held at VIL.
4. See 6.6.
FIGURE 2. Truth table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
8
DSCC FORM 2234
APR 97
FIGURE 3. Read cycle timing waveform.
FIGURE 4. Output load circuit.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
9
DSCC FORM 2234
APR 97
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Processing EPROMS. All testing requirements and quality assurance provisions herein shall be specified by the
manufacturer prior to delivery.
3.6.1 Erasure of EPROMS. When specified, devices shall be erased in accordance with the procedures and characteristics
specified in 4.4.
3.6.2 Programmability of EPROMS. When specified, devices shall be programmed to the specified pattern using the
procedures and characteristics specified in 4.5.
3.6.3 Verification of erasure or programmability of EPROMS. When specified, devices shall be verified as either programmed
to the specified program or erased. As a minimum, verification shall consist of performing a functional test (subgroup 7) to verify
that all bits are in the proper state. Any bit that does not verify to be in the proper state shall constitute a failure, and shall be
removed from the lot.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.9 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.10 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall
be done initially and after any design or process change which may affect data retention. The methods and procedures may be
vendor specific, but will guarantee the number of years listed in section 1.3 herein over the full military temperature range. The
vendor's procedure shall be kept under document control and shall be made available upon request.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-
STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
10
DSCC FORM 2234
APR 97
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c. Subgroup 4 (CIN and COUT measurement) shall be measured only for the initial test and after process or design changes
which may affect capacitance. Sample size is fifteen devices with no failures and all input and output terminals tested.
d. All devices selected for testing shall have a checkerboard pattern or equivalent. After completion of all testing, the
devices shall be verified and erased (except devices submitted for groups C and D testing).
e. Subgroups 7 and 8 shall include verification of the truth table.
TABLE II. Electrical test requirements. 1/ 2/ 3/
MIL-STD-883 test requirements Subgroups (in accordance with
method 5005, table I)
Interim electrical parameters
(method 5004) ---
Final electrical test parameters
(method 5004) 1*, 2, 3, 7, 8A, 8B, 9, 10, 11
Group A test requirements
(method 5005) 1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11
Groups C and D end-point electrical
parameters (method 5005) 2, 8A, 10
or
1, 2, 3
1/ * Indicates PDA applies to subgroups 1.
2/ Any or all subgroups may be combined when using high-speed testers.
3/ ** See 4.3.1c.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-
STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
c. All devices selected for testing shall be programmed with a checkerboard pattern, then verified and erased.
4.4 Erasing procedures. The recommended erasing procedure shall be as specified by the device manufacturer and shall be
made available upon request.
4.5 Programming procedures. The programming procedures shall be as specified by the device manufacturer and shall be
made available upon request.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87661
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
F SHEET
11
DSCC FORM 2234
APR 97
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be
used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC
5962) should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DSCC-VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 06-09-29
Approved sources of supply for SMD 5962-87661 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate
of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of
supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit
drawing PIN 1/
Vendor
CAGE
number
Vendor
similar PIN 2/
5962-8766101XA 3/
3/
0C7V7
AM27C128-90/BXA
WS27C128F-90DMB
27C128-90
5962-8766101YA 3/
3/
0C7V7
AM27C128-90/BUA
WS27C128F-90CMB
27C128-90
5962-8766102XA 3/
3/
0C7V7
AM27C128-120/BXA
WS27C128L-12DMB
27C128-120
5962-8766102YA 3/
3/
0C7V7
AM27C128-120/BUA
WS27C128L-12CMB
27C128-120
5962-8766103XA 3/
3/
3/
0C7V7
AM27C128-150/BXA
27C128-15BXA
WS27C128L-15DMB
27C128-150
5962-8766103YA 3/
3/
3/
0C7V7
AM27C128-150/BUA
27C128-15BUC
WS27C128L-15CMB
27C128-150
5962-8766104XA 3/
3/
3/
0C7V7
AM27C128-170/BXA
27C128-17BXA
WS27C128L-17DMB
27C128-170
5962-8766104YA 3/
3/
3/
0C7V7
AM27C128-170/BUA
27C128-17BUC
WS27C128L-17CMB
27C128-170
5962-8766105XA 3/
3/
3/
3/
3/
0C7V7
SMJ27C128-20JM
AM27C128-200/BXA
MD27C128-20
27C128-20BXA
WS27C128L-20DMB
27C128-200
5962-8766105YA 3/
3/
3/
0C7V7
AM27C128-200/BUA
27C128-20BUC
WS27C128L-20CMB
27C128-200
See footnotes at end of table.
STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.
Standard
microcircuit
drawing PIN 1/
Vendor
CAGE
number
Vendor
similar PIN 2/
5962-8766106XA 3/
3/
3/
3/
0C7V7
SMJ27C128-25JM
AM27C128-250/BXA
WS27C128L-25DMB
27C128-25BXA
27C128-250
5962-8766106YA 3/
3/
3/
0C7V7
AM27C128-250/BUA
WS27C128L-25CMB
27C128-25BUC
27C128-250
5962-8766107XA 3/
3/
3/
3/
0C7V7
SMJ27C128-30JM
AM27C128-300/BXA
WS27C128L-30DMB
27C128-30BXA
27C128-300/BXA
5962-8766107YA 3/
3/
3/
0C7V7
AM27C128-300/BUA
WS27C128L-30CMB
27C128-30BUC
27C128-300
5962-8766108XA 0C7V7
0C7V7 WS57C128FB-70DMB
27C128-70
5962-8766108YA 0C7V7
0C7V7 WS57C128FB-70CMB
27C128-70
1/ The lead finish shown for each PIN representing a hermetic package is the
most readily available from the manufacturer listed for that part. If the desired
lead finish is not listed, contact the Vendor to determine its availability.
2/ Caution: Do not use this number for item acquisition. Items acquired to this
number may not satisfy the performance requirements of this drawing.
3/ Not available from an approved source.
Vendor CAGE Vendor name Manufacturing Device
number and address code code
0C7V7 QP Labs 01H 16H
2945 Oakmead Village Court
Santa Clara, CA 95051
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.