50 MHz to 3.5 GHz, 45 dB RF Detector AD8312 Data Sheet FEATURES GENERAL DESCRIPTION Complete RF detector function Typical range: -45 dBm to 0 dBm, referencing 50 Frequency response from 50 MHz to 3.5 GHz Temperature stable linear in dB response Accurate to 3.5 GHz Rapid response: 85/120 ns (rise/fall) Low power: 12 mW at 2.7 V The AD8312 is a complete, low cost subsystem for the measurement of radio frequency (RF) signals in the frequency range of 50 MHz to 3.5 GHz. It has a typical dynamic range of 45 dB and is intended for use in a wide variety of cellular handsets and other wireless devices. It provides a wider dynamic range and better accuracy than possible using discrete diode detectors. In particular, its temperature stability is excellent over the full operating range of -40C to +85C. Its high sensitivity allows measurement at low power levels, thus reducing the amount of power that needs to be coupled to the detector. It is essentially a voltage responding device, with a typical signal range of 1.25 mV to 224 mV rms or -45 dBm to 0 dBm, referencing 50 . APPLICATIONS Cellular handsets (GSM, CDMA, WCDMA) RSSI and TSSI for wireless terminal devices Transmitter power measurement For convenience, the signal is internally ac-coupled, using a 5 pF capacitor to a load of 3 k in shunt with 1.3 pF. This highpass coupling, with a corner at approximately 16 MHz, determines the lowest operating frequency. Therefore, the source may be dc grounded. The AD8312 output, VOUT, increases from close to ground to about 1.2 V because the input signal level increases from 1.25 mV to 224 mV. A capacitor may be connected between the VOUT and CFLT pins when it is desirable to increase the time interval over which averaging of the input waveform occurs. The AD8312 is available in a 6-ball, 1.0 mm x 1.5 mm, wafer level chip scale package and consumes 4.2 mA from a 2.7 V to 5.5 V supply. FUNCTIONAL BLOCK DIAGRAM CFLT V-I VSET I-V VOUT BAND-GAP REFERENCE VPOS - + DET DET DET DET RFIN 10dB 10dB 10dB 10dB OFFSET COMPENSATION AD8312 COMM 05260-001 DET Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2005-2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD8312 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Transfer Function in Terms of Slope and Intercept ............... 13 Applications ....................................................................................... 1 Filter Capacitor ....................................................................... 14 General Description ......................................................................... 1 Input Coupling Options ........................................................ 14 Functional Block Diagram .............................................................. 1 Increasing the Logarithmic Slope ........................................ 15 Revision History ............................................................................... 2 Effect of Waveform Type on Intercept ................................ 15 Specifications..................................................................................... 3 Temperature Drift .................................................................. 16 Absolute Maximum Ratings ............................................................ 6 Operation Above 2.5 GHz .................................................... 16 ESD Caution .................................................................................. 6 Device Handling ..................................................................... 16 Pin Configuration and Function Descriptions ............................. 7 Evaluation Board .................................................................... 16 Typical Performance Characteristics ............................................. 8 Outline Dimensions ....................................................................... 19 General Description ....................................................................... 12 Ordering Guide .......................................................................... 19 Applications ..................................................................................... 13 Basic Connections ...................................................................... 13 REVISION HISTORY 12/15--Rev. A to Rev. B Change to Figure 30 Caption ........................................................ 16 1/11--Rev. 0 to Rev. A Changes to Figure 29 ...................................................................... 16 Updated Outline Dimensions ....................................................... 19 Changes to Ordering Guide .......................................................... 19 4/05--Revision 0: Initial Version Rev. B | Page 2 of 20 Data Sheet AD8312 SPECIFICATIONS VS = 3 V, CFLT = open, TA = 25C, light condition = 600 LUX, 52.3 termination resistor at RFIN, unless otherwise noted. Table 1. Parameter SIGNAL INPUT INTERFACE Specified Frequency Range Input Voltage Range Equivalent Power Range DC Resistance to COMM MEASUREMENT MODE f = 50 MHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage--High Power In Output Voltage--Low Power In Temperature Sensitivity f = 100 MHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage--High Power In Output Voltage--Low Power In Temperature Sensitivity f = 900 MHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage--High Power In Output Voltage--Low Power In Temperature Sensitivity Test Conditions/Comments RFIN (Pin 6) Internally ac-coupled 52.3 external termination Min Typ Max Unit 3.5 224 0 100 GHz mV rms dBm k 3050 || 1.4 50 42 3 -47 20.25 -51.5 0.841 0.232 || pF dB dB dBm dBm mV/dB dBm V V 0.0010 0.0073 dB/C dB/C 2900 || 1.3 48 40 2 -46 21.0 -50.5 0.850 0.222 || pF dB dB dBm dBm mV/dB dBm V V 0.05 1.25 -45 VOUT (Pin 2) shorted to VSET (Pin 3), sinusoidal input signal TA = 25C -40C < TA < +85C 1 dB error 1 dB error PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA +85C -40C TA +25C TA = 25C -40C < TA < +85C 1 dB error 1 dB error 19.0 -56.0 PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA +85C -40C TA +25C TA = 25C -40C < TA < +85C 1 dB error 1 dB error PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA 85C -40C TA +25C Rev. B | Page 3 of 20 23.0 -47.0 0.0002 0.0060 dB/C dB/C 890 || 1.15 49 42 1 -48.0 20.25 -51.9 0.847 0.237 || pF dB dB dBm dBm mV/dB dBm V V 0.0019 0.0010 dB/C dB/C AD8312 Parameter f = 1.9 GHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage - High Power In Output Voltage - Low Power In Temperature Sensitivity f = 2.2 GHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage--High Power In Output Voltage--Low Power In Temperature Sensitivity f = 2.5 GHz Input Impedance 1 dB Dynamic Range Maximum Input Level Minimum Input Level Slope Intercept Output Voltage--High Power In Output Voltage--Low Power In Temperature Sensitivity OUTPUT INTERFACE Minimum Output Voltage Maximum Output Voltage 1 General Limit Available Output Current Residual RF (at 2f ) Output Noise Fall Time Rise Time VSET INTERFACE Input Resistance Bias Current Source Data Sheet Test Conditions/Comments Min TA = 25C -40C < TA < +85C 1 dB error 1 dB error PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA 85C -40C TA +25C TA = 25C -40C < TA < +85C 1 dB error 1 dB error PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA 85C -40C TA +25C TA = 25C -40C < TA < +85C 1 dB error 1 dB error PIN = -10 dBm PIN = -40 dBm PIN = -10 dBm 25C TA 85C -40C TA +25C VOUT (Pin 2) No signal at RFIN, RL 10 k RL 10 k 2.7 V VS 5.5 V Sourcing/sinking f = 0.1 GHz (worst condition) RF input = 2.2 GHz, -10 dBm, fNOISE = 100 kHz, CFLT open Input level = off to 0 dBm, 90% to 10% Input level = 0 dBm to off, 10% to 90% VSET (Pin 3) RFIN = -10 dBm; VSET = 1.2 V Rev. B | Page 4 of 20 1.8 VS - 1.2 Typ Max Unit 450 || 1.13 48 40 1 -47 19.47 -52.4 0.826 0.240 || pF dB dB dBm dBm mV/dB dBm V V 0.004 0.005 dB/C dB/C 430 || 1.09 48 40 1 -47 19.1 -52.1 0.803 0.230 || pF dB dB dBm dBm mV/dB dBm V V -0.0023 0.0055 dB/C dB/C 400 || 1.03 49 40 1 -48 18.6 -51.2 0.762 0.204 || pF dB dB dBm dBm mV/dB dBm V V 0.005 -0.0126 dB/C dB/C 0.02 2.0 VS - 1 2/0.1 100 1.4 120 85 13 75 0.2 V V V mA V V/Hz ns ns k A Data Sheet Parameter POWER INTERFACE Supply Voltage Quiescent Current vs. Temperature 1 AD8312 Test Conditions/Comments VPOS (Pin 1) -40C TA +85C Increased output is possible when using an attenuator between VOUT and VSET to raise the slope. Rev. B | Page 5 of 20 Min Typ Max Unit 2.7 2.8 3.0 4.2 4.3 5.5 5.7 V mA mA AD8312 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltage VPOS VOUT, VSET Input Voltage Equivalent Power Internal Power Dissipation JA (WLCSP) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Value 5.5 V 0 V, VPOS 1.6 V rms 17 dBm 200 mW 200C/W 125C -40C to +85C -65C to +150C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION Rev. B | Page 6 of 20 Data Sheet AD8312 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS AD8312 1 6 RFIN VOUT 2 5 COMM VSET 3 4 CFLT TOP VIEW (Not to Scale) 05260-002 VPOS Figure 2. Pin Configuration Table 3. Pin Function Descriptions Ball No. 1 2 3 Mnemonic VPOS VOUT VSET 4 CFLT 5 6 COMM RFIN Description Positive Supply Voltage (VS), 2.7 V to 5.5 V. Logarithmic Output. Output voltage increases with increasing input amplitude. Setpoint Input. Connect VSET to VOUT for measurement mode operation. The nominal logarithmic slope of 20 mV/dB can be increased to an arbitrarily high value by attenuating the signal between VOUT and VSET (see the Increasing the Logarithmic Slope section). Connection for an External Capacitor to Slow the Response of the Output. Capacitor is connected between CFLT and VOUT. Device Common (Ground). RF Input. Rev. B | Page 7 of 20 AD8312 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VS = 3 V; TA = 25C; CFLT = open; light condition = 600 LUX, 52.3 termination; unless otherwise noted. Colors: +25C = black, -40C = blue, +85C = red. 2.5 2.0 1.5 2.5 +85C +25C -40C 1.00 2.0 1.5 0.50 -0.5 0 -1.0 -50 -40 -20 -30 PIN (dBm) -10 0 -2.5 10 Figure 3. VOUT and Logarithmic Conformance vs. Input Amplitude at 50 MHz; Typical Device at -40C, +25C, and +85C 1.25 1.00 -2.0 0 -60 -50 -40 -20 -30 PIN (dBm) -10 0 1.25 1.5 2.5 +85C +25C -40C 2.0 1.00 2.0 1.5 1.0 0 -0.5 0.50 VOUT (V) 0.5 ERROR (dB) VOUT (V) 1.0 0.75 0.5 0.75 0 -0.5 0.50 -1.0 -1.0 -1.5 -2.0 0 -60 -50 -40 -30 -20 PIN (dBm) -10 0 -2.5 10 Figure 4. VOUT and Logarithmic Conformance vs. Input Amplitude at 100 MHz; Typical Device at -40C, +25C, and +85C 1.25 1.00 -2.0 0 -60 -50 -40 -30 -20 PIN (dBm) -10 0 1.25 1.00 1.5 2.5 +85C +25C -40C 2.0 2.0 1.5 1.0 0 -0.5 0.50 VOUT (V) 0.5 ERROR (dB) VOUT (V) 1.0 0.75 0.5 0.75 0 -0.5 0.50 -1.0 -1.0 0.25 -50 -40 -30 -20 PIN (dBm) -10 0 -2.0 05260-005 -2.5 10 -1.5 0.25 -1.5 -2.0 0 -60 -2.5 10 Figure 7. VOUT and Logarithmic Conformance vs. Input Amplitude at 2.2 GHz; Typical Device at -40C, +25C, and +85C 2.5 +85C +25C -40C -1.5 0.25 05260-004 0.25 -2.5 10 Figure 6. VOUT and Logarithmic Conformance vs. Input Amplitude at 1.9 GHz; Typical Device at -40C, +25C, and +85C 2.5 +85C +25C -40C -1.5 0.25 05260-003 -2.0 0 -60 -1.0 -1.5 0.25 ERROR (dB) 0.5 05260-006 -0.5 0.75 ERROR (dB) 0 0.50 1.0 VOUT (V) 0.5 ERROR (dB) VOUT (V) 1.0 0.75 05260-007 1.00 1.25 ERROR (dB) +85C +25C -40C Figure 5. VOUT and Logarithmic Conformance vs. Input Amplitude at 900 MHz; Typical Device at -40C, +25C, and +85C 0 -60 -50 -40 -30 -20 PIN (dBm) -10 0 -2.5 10 05260-008 1.25 Figure 8. VOUT and Logarithmic Conformance vs. Input Amplitude at 2.5 GHz; Typical Device at -40C, +25C, and +85C Rev. B | Page 8 of 20 Data Sheet AD8312 1.5 1.0 0.5 0.5 ERROR (dB) 1.0 0 -0.5 -1.5 -1.5 05260-009 -1.0 -2.5 -60 -50 -40 -30 -20 PIN (dBm) -10 0 2.5 -2.0 -2.5 -60 10 Figure 9. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 50 MHz for 80 Devices 1.5 1.5 0.5 ERROR (dB) 0.5 0 -0.5 -1.5 05260-010 -1.5 -30 -20 PIN (dBm) -10 0 2.5 -2.5 -60 1.5 1.5 0.5 ERROR (dB) 0.5 0 -0.5 -1.5 05260-011 -1.5 -30 -20 PIN (dBm) -10 0 10 -2.0 -2.5 -60 10 Figure 11. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 900 MHz for 80 Devices 0 -0.5 -1.0 -40 -10 0 -1.0 -2.0 -30 -20 PIN (dBm) +85C +25C -40C 2.0 1.0 -50 -40 2.5 1.0 -2.5 -60 -50 Figure 13. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 2.2 GHz for 80 Devices +85C +25C -40C 2.0 10 -2.0 10 Figure 10. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 100 MHz for 80 Devices 0 -0.5 -1.0 -40 -10 0 -1.0 -2.0 -30 -20 PIN (dBm) +85C +25C -40C 2.0 1.0 -50 -40 2.5 1.0 -2.5 -60 -50 Figure 12. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 1.9 GHz for 80 Devices +85C +25C -40C 2.0 ERROR (dB) -0.5 -1.0 -2.0 ERROR (dB) 0 05260-012 1.5 +85C +25C -40C 2.0 05260-013 2.0 ERROR (dB) 2.5 +85C +25C -40C 05260-014 2.5 -50 -40 -30 -20 PIN (dBm) -10 0 10 Figure 14. Distribution of Error at -40C, +25C, and +85C After Ambient Normalization vs. Input Amplitude at 2.5 GHz for 80 Devices Rev. B | Page 9 of 20 AD8312 Data Sheet 100ns/HORIZ DIV RISE TIME 85ns FALL TIME 120ns 500mV/ VERT DIV VOUT 500mV/VERT DIV VPOS 2V/VERT DIV 05260-015 PULSED RF 0.1GHz, 0dBm 200mV/VERT DIV 1s/HORIZ DIV Figure 15. VOUT Response Time, RF Off to 0 dBm ROHDE & SCHWARZ SMT06 GENERATOR PULSE MODULATION 10MHz HP8648B REF OUTPUT SIGNAL GENERATOR TRIG OUT RF OUT +3dB PULSE OUT -3dB RF SPLITTER AD811 1 VPOS RFIN 6 2 VOUT COMM 5 52.3 CH3* CFLT 4 NC NC = NO CONNECT AD8312 TEKTRONIX TDS51504 SCOPE CH1 *50 TERMINATION 2 VOUT COMM 5 3 VSET 52.3 CFLT 4 NC TEKTRONIX TDS784C SCOPE TEKTRONIX P6204 FET PROBE Figure 19. Test Setup for Power-On and Power-Off Response 10k 0.5 1 2 0.1GHz 0.9GHz -j0.2 100 0dBm -10dBm -20dBm -40dBm -60dBm RF OFF 10 1.9GHz 2.2GHz 2.5GHz -j2 1 05260-017 3.5GHz 1k 1 -j1 Figure 17. Input Impedance vs. Frequency; No Termination Resistor on RFIN Rev. B | Page 10 of 20 3 10 30 100 300 FREQUENCY (kHz) 1k 3k Figure 20. Noise Spectral Density of Output; CFLT = Open 10k 05260-020 NOISE SPECTRAL DENSITY (nV/ Hz) +j2 +j0.2 -j0.5 RFIN 6 TRIG +j1 +j0.5 0.2 VPOS NC = NO CONNECT Figure 16. Test Setup for Pulse Response 0 1 TRIG 05260-016 VSET 49.9 732 -3dB 0.1F 3 TRIG HP8116A OUT PULSE GENERATOR EXT TRIG 20dBm RF OUT AD8312 3V Figure 18. Power-On and Power-Off Response 05260-019 RF INPUT 05260-018 VOUT Data Sheet AD8312 Table 4. Typical Specifications at Selected Frequencies at 25C (Mean and ) Frequency (GHz) 0.05 0.1 0.9 1.9 2.2 2.5 3.0 3.5 1 Slope (mV/dB) 20.25 0.3 21.0 0.2 20.25 0.3 19.47 0.3 19.1 0.4 18.6 0.6 17.5 0.7 17.1 0.7 Intercept (dBm) -51.5 0.4 -50.5 0.4 -51.9 0.4 -52.4 0.6 -52.1 0.85 -51.2 1.2 -46.9 2.5 -42.6 2.5 Refer to Figure 23. Rev. B | Page 11 of 20 1 dB Dynamic Range 1 (dBm) High Point Low Point +3.0 0.12 -48.0 0.13 +2.0 0.1 -46.0 0.1 +0.2 0.1 -49.0 0.2 +1.5 0.12 -48.8 0.3 +1.5 0.2 -48.5 0.4 +2.0 0.3 -47.7 0.5 -4 0.3 -46 0.4 -1 0.3 -39 0.3 AD8312 Data Sheet GENERAL DESCRIPTION In measurement modes, this output is connected back to a voltage-to-current (V-to-I) stage, in such a manner that VOUT is a logarithmic measure of the RF input voltage with a slope and intercept controlled by the design. For a fixed termination resistance at the input of the AD8312, a given voltage corresponds to a certain power level. The AD8312 is a logarithmic amplifier similar in design to the AD8313; further details about the structure and function may be found in the AD8313 data sheet and the data sheets of other logarithmic amplifiers produced by Analog Devices, Inc., Figure 21 shows the main features of the AD8312 in block schematic form. The AD8312 combines two key functions needed for the measurement of signal level over a moderately wide dynamic range. First, it provides the amplification needed to respond to small signals in a chain of four amplifier/limiter cells, each having a small signal gain of 10 dB and a bandwidth of approximately 3.5 GHz. At the output of each amplifier stage is a full wave rectifier, essentially a square law detector cell, which converts the RF signal voltages to a fluctuating current with an average value that increases with signal level. A further passive detector stage is added ahead of the first stage. Therefore, there are five detectors, each separated by 10 dB, spanning some 50 dB of dynamic range. The overall accuracy at the extremes of this total range, viewed as the deviation from an ideal logarithmic response, that is, the law conformance error, can be judged by reference to Figure 3 through Figure 8, which show that errors across the central 40 dB are moderate. These figures show how the conformance to an ideal logarithmic function varies with temperature and frequency. The external termination added before the AD8312 determines the effective power scaling. This often takes the form of a simple resistor (52.3 provides a net 50 input), but more elaborate matching networks may be used. This impedance determines the logarithmic intercept, the input power for which the output would cross the baseline (VOUT = 0) if the function were continuous for all values of input. Since this is never the case for a practical logarithmic amplifiers, the intercept refers to the value obtained by the minimum error, straight line fit to the actual graph of VOUT vs. input power. The quoted values assume a sinusoidal (CW) signal. Where there is complex modulation, as in CDMA, the calibration of the power response needs to be adjusted accordingly. Where a true power (waveform independent) response is needed, the use of an rms responding detector, such as the AD8361, should be considered. However, in terms of the logarithmic slope, the amount by which the output VOUT changes for each decibel of input change (voltage or power), is, in principle, independent of waveform or termination impedance. In practice, it usually falls off at higher frequencies because of the declining gain of the amplifier stages and other effects in the detector cells. For the AD8312, the slope at low frequencies is nominally 21.0 mV/dB, falling almost linearly with frequency to about 18.6 mV/dB at 2.5 GHz. These values are sensibly independent of temperature and almost totally unaffected by supply voltages of 2.7 V to 5.5 V. The output of these detector cells is in the form of a differential current, making their summation a simple matter. It can easily be shown that such summation closely approximates a logarithmic function. This result is then converted to a voltage at the VOUT pin through a high gain stage. CFLT V-I VSET I-V VOUT BAND-GAP REFERENCE VPOS - + DET DET DET DET RFIN 10dB 10dB OFFSET COMPENSATION 10dB 10dB AD8312 COMM Figure 21. Block Schematic Rev. B | Page 12 of 20 05260-021 DET Data Sheet AD8312 APPLICATIONS INFORMATION 1.2 BASIC CONNECTIONS VOUT 1 0.6 0 0.4 -1 0 -60 1 VPOS RFIN 6 2 VOUT COMM 5 3 VSET CFLT 4 INPUT OPTIONAL (SEE TEXT) INTERCEPT -50 -40 -30 -20 PIN (dBm) -10 0 -3 10 Figure 23. VOUT and Logarithmic Conformance Error vs. Input Level vs. Input Level at 900 MHz TRANSFER FUNCTION IN TERMS OF SLOPE AND INTERCEPT 05260-022 CF OPTIONAL (SEE TEXT) -2 3dB DYNAMIC RANGE 52.3 ERROR (dB) 0.8 0.2 AD8312 VS 2 1dB DYNAMIC RANGE 05260-023 0.1F 1.0 VOUT (V) Figure 22 shows the basic connections for measurement mode. A supply voltage of 2.7 V to 5.5 V is required. The supply to the VPOS pin should be decoupled with a low inductance 0.1 F surface-mount ceramic capacitor. A series resistor of about 10 may be added; this resistor slightly reduces the supply voltage to the AD8312 (maximum current into the VPOS pin is approximately 5.7 mA). Its use should be avoided in applications where the power supply voltage is very low (that is, 2.7 V). A series inductor provides similar power supply filtering with minimal drop in supply voltage. 3 VS= 2.7V RT = 52.3 Figure 22. Basic Connections for Operation in Measurement Mode The AD8312 has an internal input coupling capacitor. This eliminates the need for external ac coupling. In this example, a broadband input match is achieved by connecting a 52.3 resistor between RFIN and ground. This resistance combines with the internal input impedance of approximately 3 k to give an overall broadband input resistance of 50 . Several other coupling methods are possible; these are described in the Input Coupling Options section. The measurement mode is selected by connecting VSET to VOUT, which establishes a feedback path and sets the logarithmic slope to its nominal value. The peak voltage range of the measurement extends from -49 dBm to 0 dBm at 0.9 GHz and is only slightly less at higher frequencies up to 2.5 GHz. At a slope of 21.0 mV/dB, this would amount to an output span of 1.029 V. Figure 23 shows the transfer function for VOUT at a supply voltage of 2.7 V and an input frequency of 900 MHz. The load resistance on VOUT should not be lower than 4 k so that the full-scale output can be generated with the limited available current of 1 mA maximum. Figure 23 shows the logarithmic conformance under the same conditions. The transfer function of the AD8312 is characterized in terms of its slope and intercept. The logarithmic slope is defined as the change in the RSSI output voltage for a 1 dB change at the input. For the AD8312, the slope is nominally 20 mV/dB. Therefore, a 10 dB change at the input results in a change at the output of approximately 200 mV. Figure 23 shows the range over which the device maintains its constant slope. The dynamic range can be defined as the range over which the error remains within a certain band, usually 1 dB or 3 dB. In Figure 23, for example, the 1 dB dynamic range is approximately 51 dB (from -49 dBm to +2 dBm). The intercept is the point at which the extrapolated linear response would intersect the horizontal axis (see Figure 23). Using the slope and intercept, the output voltage can be calculated for any input level within the specified input range by VOUT VSLOPE (PIN PO ) where: VOUT is the demodulated and filtered RSSI output. VSLOPE is the logarithmic slope, expressed in V/dB. PIN is the input signal, expressed in decibels relative to some reference level (dBm in this case). PO is the logarithmic intercept, expressed in decibels relative to the same reference level. For example, at an input level of -27 dBm, the output voltage is VOUT 0 .020 V / dB [ 27 dBm ( 50 dBm )] 0 .46 V Rev. B | Page 13 of 20 AD8312 Data Sheet 1 2 x 13 k x (3.5 pF + C F ) Input Coupling Options The internal 5 pF coupling capacitor of the AD8312, along with the low frequency input impedance of 3 k, gives a high pass input corner frequency of approximately 16 MHz. This sets the minimum operating frequency. Figure 24 to Figure 26 show three options for input coupling. A broadband resistive match can be implemented by connecting a shunt resistor to ground at RFIN (see Figure 24). This 52.3 resistor (other values can also be used to select different overall input impedances) combines with the input impedance of the AD8312 (2.9 k || 1.3 pF) to give a broadband input impedance of 50 . While the input resistance and capacitance (RIN and CIN) varies by approximately 20% from device to device, the dominance of the external shunt resistor means that the variation in the overall input impedance is close to the tolerance of the external resistor. where: R2 is the input impedance of the AD8312. R1 is the source impedance to which the AD8312 is being matched. Note that this gain is only achieved for a perfect match. Component tolerances and the use of standard values tend to reduce gain. 50 RFIN CC RSHUNT 52.3 CIN RIN VBIAS Figure 24. Broadband Resistive Method for Input Coupling AD8312 50 SOURCE 50 X1 RFIN CC X2 At frequencies above 2 GHz, the input impedance drops below 450 ; therefore, it is appropriate to use a larger shunt resistor value. This value is calculated by plotting the input impedance (resistance and capacitance) on a Smith Chart and by choosing the best shunt resistor value to bring the input impedance closest to the center of the chart (see Figure 17). At 2.5 GHz, a shunt resistor of 57.6 is recommended. CIN RIN VBIAS Figure 25. Narrow-Band Reactive Method for Input Coupling AD8312 RFIN A reactive match can also be implemented as shown in Figure 25. This is not recommended at low frequencies because device tolerances dramatically vary the quality of the match due to the large input resistance. For low frequencies, Figure 24 or Figure 26 is recommended. In Figure 25, the matching components are drawn as general reactances. Depending on the frequency, the input impedance at that frequency and the availability of standard value components, either a capacitor or an inductor, is used. As in the previous case, the input impedance at a particular frequency is plotted on a Smith Chart and matching components are chosen (Shunt or Series L, or Shunt or Series C) to move the impedance to the center of the chart. Matching components for specific frequencies can be calculated using the Smith Chart (see Figure 17). Table 5 outlines the input impedances for some commonly used frequencies. AD8312 50 SOURCE 05260-024 Video Bandwidth = R2 R1 Voltage GaindB = 20 log 10 05260-025 The video bandwidth of VOUT is approximately 3.5 MHz. In CW applications where the input frequency is much higher than this, no further filtering of the demodulated signal is required. Where there is a low frequency modulation of the carrier amplitude, however, the low pass corner must be reduced by the addition of an external filter capacitor, CF (see Figure 22). The video bandwidth is related to CF by The impedance matching characteristics of a reactive matching network provide voltage gain ahead of the AD8312, which increases device sensitivity (see Table 5). The voltage gain is calculated by STRIPLINE RATTN CC CIN RIN VBIAS 05260-026 Filter Capacitor Figure 26. Series Attenuation Method for Input Coupling Figure 26 shows a third method for coupling the input signal into the AD8312, which is applicable in applications where the input signal is larger than the input range of the logarithmic amplifier. A series resistor, connected to the RF source, combines with the input impedance of the AD8312 to resistively divide the input signal being applied to the input. This has the advantage of very little power being tapped off in RF power transmission applications. Rev. B | Page 14 of 20 Data Sheet AD8312 4.0 Table 5. Input Impedance for Select Frequency Real 0.967 0.962 0.728 0.322 0.230 0.165 0.126 0.146 S11 Imaginary -0.043 -0.081 -0.535 -0.891 -0.832 -0.845 -0.849 -0.826 Impedance (Series) 1090 - j 1461 422.6 - j 1015 25.6 - j 148.5 11.5 - j 72.69 9.91 - j 64.74 9.16 - j 59.91 8.83 - j 57.21 10.5 - j 58.54 3.5 3.0 5.0V SUPPLY 2.5 VOUT (V) Frequency (GHz) 0.05 0.1 0.9 1.9 2.2 2.5 3.0 3.5 2.0 3.0 1.5 2.7V SUPPLY 2.0 1.0 1.0 0 -60 The nominal logarithmic slope of 20 mV/dB can be increased to an arbitrarily high value by attenuating the signal between VOUT and VSET, as shown in Figure 27. The ratio R1/R2 is set by -50 -40 -30 -20 PIN (dBm) -10 0 10 Figure 28. VOUT vs. Input Level at Various Logarithmic Slopes Effect of Waveform Type on Intercept New Slope 1 R1/R2 Original Slope In the example shown, two 2 k resistors combine to change the slope at 1900 MHz from approximately 20 mV/dB to 40 mV/dB. Note that R2 is in parallel with the input resistance of VSET, typically 13 k. Therefore, the exact R1/R2 ration may vary. AD8312 R1 2k ~40mV/dB @ 1900MHz R2 2k 05260-027 VOUT VSET 05260-028 0.5 Increasing the Logarithmic Slope Figure 27. Increasing the Output Slope The slope can be increased to higher levels, as shown in Figure 28. This, however, reduces the usable dynamic range of the device, depending on the supply voltage. Output loading should be considered when choosing resistor values for slope adjustment to ensure proper output swing. Note that the load resistance on VOUT should not be lower than 4 k in order that the full-scale output can be generated with the limited available current of 1 mA. Although specified for input levels in dBm (dB relative to 1 mW), the AD8312 fundamentally responds to voltage and not to power. A direct consequence of this characteristic is that input signals of equal rms power but differing crest factors, produce different results at the output of the logarithmic amplifier. The effect of differing signal waveforms is to shift the effective value of the intercept upwards or downwards. Graphically, this looks like a vertical shift in the logarithmic amplifier transfer function. The logarithmic slope, however, is not affected. For example, consider the case of the AD8312 being alternately fed by an unmodulated sine wave and by a 64 QAM signal of the same rms power. The output voltage of the AD8312 differs by the equivalent of 1.6 dB (31 mV) over the complete dynamic range of the device (with the output for a 64 QAM input being lower). Figure 29 shows the transfer function of the AD8312 when driven by both an unmodulated sine wave and several different signal waveforms. For precision operation, the AD8312 should be calibrated for each signal type that is driving it. To measure the rms power of a 64 QAM input, for example, the mV equivalent of the dB value (19.47 mV/dB x 1.6 dB) should be subtracted from the output voltage of the AD8312. Rev. B | Page 15 of 20 AD8312 Data Sheet 0.9 3 0.8 IS-95 REV 0 -1 -2 -4 -5 -60 -40 -50 -30 64 QAM -20 -10 0 10 Figure 29. Shift in Transfer Function due to Several Different Signal Waveforms Figure 30 shows the logarithmic slope and error over temperature for a 0.9 GHz input signal. Error due to drift over temperature consistently remains within 0.5 dB and only begins to exceed this limit when the ambient temperature goes above 70C. For all frequencies using a reduced temperature range, higher measurement accuracy is achievable. 0.8 -30 -20 PIN (dBm) -10 -1 0.3 -2 0.2 -3 0.1 -4 -45 -35 -25 PIN (dBm) -15 -5 5 -5 5 +85C +25C -40C 0.8 4 3 1 0.5 0 0.4 -1 1.5 0.3 -2 1.0 0.2 -3 0.5 0.1 -4 -0.5 -2.5 10 Figure 30. Typical Drift at 900 MHz for Various Temperatures Operation Above 2.5 GHz The AD8312 works at high frequencies, but exhibits slightly higher output voltage temperature drift. Figure 31 and Figure 32 show the transfer functions and error distributions of a large population of devices at 3.0 GHz and 3.5 GHz over temperature. Due to the repeatability of the drift from device to device, compensation can be applied to reduce the effects of temperature drift. In the case of the 3.5 GHz distribution, an intercept correction of 2.0 dB at 85C would improve the accuracy of the distribution to 2 dB over a +40 dB range. 05260-030 -1.5 -2.0 0 -55 -45 -35 -25 PIN (dBm) -15 -5 5 -5 Figure 32. Output Voltage and Error at -40C, +25C, and +85C after Ambient Normalization vs. Input Amplitude at 3.5 GHz for 30 Devices -1.0 0 0.4 0.6 0 -40 0 0.9 ERROR (dB) VOUT (V) 1.0 -50 0.5 2 2.0 0 -60 1 0.7 2.5 0.3 0.6 1.0 VOUT (V) 1.3 +85C +70C +25C 0C -10C -20C -40C 2 Figure 31.Output Voltage and Error at -40C, +25C, and +85C after Ambient Normalization vs. Input Amplitude at 3.0 GHz for 60 Devices Temperature Drift 0.5 0.7 0 -55 INPUT (dBm) 3 ERROR (dB) WCDMA 64-CH 05260-029 -3 4 05260-032 CW 1 VOUT (V) ERROR (dB) 2 5 +85C +25C -40C ERROR (dB) 1.0 4 05260-031 5 Device Handling The wafer level chip scale package consists of solder bumps connected to the active side of the die. The device is lead free with 95.5% tin, 4.0% silver, and 0.5% copper solder bump composition. The WLCSP package can mount on printed circuit boards using standard surface-mount assembly techniques. However, take caution to avoid damaging the die. See the AN-617 application note, Wafer Level Chip Scale Package, for additional information. WLCSP devices are bumped die; exposed die can be sensitive to light conditions, which can influence specified limits. Evaluation Board Figure 33 shows the schematic of the AD8312 evaluation board. The layout and silkscreen of the component and circuit sides are shown in Figure 34 to Figure 37. The board is powered by a single supply in the 2.7 V to 5.5 V range. The power supply is decoupled by a single 0.1 F capacitor. Table 6 details the various configuration options of the evaluation board. Rev. B | Page 16 of 20 Data Sheet AD8312 C2 0.1F R1 52.3 AD8312 VPOS 1 VPOS RFIN 6 2 VOUT COMM 5 3 VSET CFLT 4 INPUT VOUT C4 (OPEN) R7 0 VSET R5 (OPEN) R8 (OPEN) R6 (OPEN) TO EDGE CONNECTOR R4 0 R2 (OPEN) C3 (OPEN) TO EDGE CONNECTOR 05260-033 R3 0 Figure 35. Layout of Component Side (WLCSP) 05260-035 Figure 36. Silkscreen of Circuit Side (WLCSP) 05260-034 Figure 34. Silkscreen of Component Side (WLCSP) 05260-037 05260-036 Figure 33. Evaluation Board Schematic Figure 37. Layout of Circuit Side (WLCSP) Rev. B | Page 17 of 20 AD8312 Data Sheet Table 6. Evaluation Board Configuration Options Component VPOS, GND C2 Function Supply and Ground Vector Pins. Power Supply Decoupling. The nominal supply decoupling consists of a 0.1 F capacitor (C1). R1 Input Interface. The 52.3 resistor in Position R1 combines with the internal input impedance of the AD8312 to give a broadband input impedance of around 50 . Slope Adjust. By installing resistors in R2 and R4, the nominal slope of 20 mV/dB can be changed. See the Increasing the Logarithmic Slope section for more details. R2, R4 C3 R3, R8, C4 Filter Capacitor. The response time of VOUT can be modified by placing a capacitor between CFLT (Pin 4) and VOUT (Pin 2). Output Interface. R3, R8, and C4 can be used to check the response of VOUT to capacitive and resistive loading. R3/R8 can be used to attenuate VOUT. R7 VSET Interface. R7 can be used to reduce capacitive loading from transmission lines. R5, R6 Alternate Interface. R5 and R6 allow for VOUT and VSET to be accessible from the edge connector, which is only used for characterization. Rev. B | Page 18 of 20 Default Condition Not Applicable C2 = 0.1 F (Size 0603) R1 = 52.3 (Size 0603) R2 = Open (Size 0402) R4 = 0 (Size 0402) C3 = Open (Size 0603) R3 = 0 (Size 0603) R8 = C4 = Open (Size 0402) R7 = 0 (Size 0603) R5 = R6 = Open (Size 0402) Data Sheet AD8312 OUTLINE DIMENSIONS 0.675 0.595 0.515 0.380 0.355 0.330 1.00 0.95 0.90 A1 BALL CORNER SEATING PLANE 0.345 0.295 0.245 1.50 1.45 1.40 2 1 A 1.00 BSC B 0.50 BSC C 0.270 0.240 0.210 0.50 BSC BOTTOM VIEW (BALL SIDE UP) 081607-B TOP VIEW (BALL SIDE DOWN) 0.075 COPLANARITY Figure 38. 6-Ball Wafer-Level Chip Scale Package [WLCSP] (CB-6-2) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD8312ACBZ-P7 AD8312ACBZ-P2 AD8312-EVALZ 1 Temperature Range -40C to +85C -40C to +85C Package Description 6-Ball WLCSP, 7" Pocket Tape and Reel 6-Ball WLCSP, 7" Pocket Tape and Reel Evaluation Board Z = RoHS Compliant Part. Rev. B | Page 19 of 20 Package Outline CB-6-2 CB-6-2 Branding Information Q00 Q00 Ordering Quantity 3000 250 AD8312 Data Sheet NOTES (c)2005-2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05260-0-12/15(B) Rev. B | Page 20 of 20