MIL SPECS Ich Oooo1eS O00e3590 0 i 2 October 143. MILITARY SPECIFICATION SEMICONDUCTOR DEVICE, DIODE, SILICON, POWER RECTIFIER TYPES 1N3164, 1N3168, 1N3170, 1N3172, 1N3174, 1N3175, 1N3176, 1N3177, AND R TYPES, JAN, JANTX, JANTXY This amendment forms a part of Military Specification MIL-S-19500/2118, dated 18 May 1983, and is approved for use by all] Departments an4 Agencies of the Department of Defense. PAGE 1 1.5: Delete "Rejc = 0.15C/W" and substitute "Rage = 0.20C/w". PAGE 3 FIGURE 1: Delete and substitute new figure 1 as printed on page 3 of this amendment. PAGE 4 4.3, add the following screen to the screening table: - T Screen (see table II of MIL-S-19500)} Measurement JANTX and JANTXV levels Method 2073 may be used in lieu of 2974 for compression bonded devic#s only. | | | | | | | | | | PAGE 8 TABLE II, Subgroup 5: Delete Rggc = 9.15C/W" and substitute "Rgjc = 0.20C/wW". The margin of this amendment is marked with asterisks to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders ard contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. wn Oo om wo na e 1 of 3 FMIL SPECS Custodians: Air Force = 17 Army = ER Navy = EC Review activities: Air Force = 11, 85 Army = AR Navy = SH User activities: Air Force = 14, 19 Army < MI Navy = CG, MC, WP Agent: DLA - ES W U.S. GOVERNMENT PRINTING OFFICE: 1985505-038/21363 Icffqogd1es 0002391 2 & Preparing activity: Army = ER (Project 5961-0978)MIL-S-19500/211B AMENDMENT 3 MIL SPECS cf oooo1es oooaaqa 4 i Q e SEE NOTE 8 E A oe . I a OM > F we TERM NO 2 SEATING PLANE Dimensions Letter Inches Millimeters |Notes NOTES: Min | Max Min Max 1. Metric equivalents are given for A 1.520 38.10 4 general information only. 2. Complete threads to extend to 530 2795 13.46 | 19.18 within 2-1/2 threads of seating Cc .063 .172 1.60 4.37 plane. 3. 3/4-16 UNF-2A. Maximum pitch pd 1.100 27.98 diameter of plated threads shall gD, .600 15.24 be basic pitch diameter (.7094 in., 18,019 mm) ref. (Screw Thread E 1,218 1,252 | 30.94 | 31.75 Standards for Federal Services) F 250 | .562 6.35 | 14.27 5 FED-STD-H28. 4, Angular orientation of terminal H 5.125 [6.750 |130,18 ]171.45 and tabulation with respect to 1, 2375 9.53 7 hex base is undefined. Square or radius on end of terminal is pM -660 | .745 | 16.76 g undefined. My 2125 3.18 6 5. Q| F Mi gD, TERM NO! TERM NO 2 H SEATING PLANE NOTES: 1. Metric equivalents are given for general information only and are 3. based upon 1 finch = 25.4 mm. Complete threads to extend to within 2-1/2 threads of seating plane. 3/4-16 UNF-2A. maximum pitch diameter of plated threads shall be basfc pitch diameter (.7094 {n., 18.01 mm) ref. (Screw Thread Standards for Federal FED-STD-H28. Services) Angular orfentation of terminal and tabulation with respect to hex base is undefined. Square or radius on end of terminal is undefined. A chamfer (or undercut) on one or both ends of hexagonal portions is optional. Tublation optional. Minimum flat. Flexible leads. FIGURE 1. E Fr c I j o + b ot T Dimensions { |Letter Trches meters [Notes] { TMIn | Maxl Min x | I A 1.500 38. T6T [aT { b | .530! .755! 13.46! 19.181 | L i J fc | .063{ .172] 1.60] 4.37 | | gp 11.100 | 27.94 {+++ gD | { .600] | 15.24 | +4 E |1.218/1.250/ 30.941 31.751 | F | .250] .562| 6.35! 14.271 5 | H |5.125]6.750/130.18{ 171.45 { 1, | 3751 = | 9.53 17} p> 4) +| gm | .660! .6701 16.76 f2f My 125 3.181 6 | Ww | .793[ .828) 20.14] 21.031 png Q 12.250] | 57.15] | 44) | | | 375) | 9.531 6 | pt | .265| .350| 6.73] 8.89! W | 1 3 i Physical dimensions for semiconductor devices.MIL SPECS rcp oogo1es oonza56 1 & MIL-S-19500/211B 4.3 Screening (JANTX and JANTXV levels only). Screening shall be in accordance with MIL-S-19500 TeabTe YT) and as specitied herein. The following measurements shall be made in accordance with Table I herein. Devices that exceed the limits of table I shall not be acceptable. 4 Ipmy = #0.5 mA(pk) or 100% of initial value whichever 1s greater. 4 Vey = 40.1 v(pk). | T | | Screen I Measurement ! | | { (See table II | | | of MIL-S-19500) | JANTX AND JANTXY LEVELS l | | T ; 4 | 25006; Performed prior to installation of external lead. | I | 10 ! Not applicable ! I | T | | 11 | Ipmi, and Vey | | ! | | ~ I 12 | Method 1038, condition A; Ypm = Vy rated See 1.4), I | | Tp = 180C. # 280 Hz. I | | I | T | ! 13 Subgroup 2 of table I herein: | | | | | | | | | | I | | | | | { 4.4 Quality conformance inspection. Quality conformance inspection shall be in accordance with MIL-S-19500. 4.4.1 Group A inspection. Group A inspection shall be conducted in accordance with MIL-S~19500 and table I heretn. End point electrical measurements shall be in accordance with the applicable steps of table IV herein. 4.4.2 Group B inspection. Group B inspection shall be conducted in accordance with the conditions for subgroup testing in table IVb of MIL-S-19500 and table II herein. Electrical measurements (end points) shall be in accordance with the applicable steps of table IV herein. 4.4.3 Group C inspection. Group C inspection shall be conducted in accordance with the conditions specified for Subgroup testing in table V of MIL~S-19500 and table III herein. Electrical measurements (end points) shall be in accordance with the applicable steps of table IV erein. 4.5 Methods of examination and test. Methods of examination and test shall be as specified in the appropriate tables and as follows. 4.5.1 Power cycling. One complete cycle for this test shall be as follows: First, heat the case to the maximum temperature specified, by passing the specified amount of short-circuit forward current through the diode under test. Then, remove the applied current and allow the case temperature to cool to the minimum case temperature specified. No time limit {ts applicable to any one cycles but the cycling shall be continuous until the required number of cycles has been completed.MIL SPECS 5. PACKAGING TcBooog1es on0e39? 3 MIL-S-19500/211B , 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-S-19500. 6. NOTES 6.1 Notes. The notes specified in MIL-S-19500 are applicable to the specification. Custodians: Air Force - 17 Army - ER Navy - EC Review activities: Air Force - 11, 85 Army - AR Navy - SH User activities: Air Force - 14, 19 Amy - MI Navy - CG, MC, WP Agent. DLA - ES Preparing activity: Army - ER (Project 5961-0887)gooo12eS Oooe#348 5 & MIL SPECS icf MIL-S-19500/2118 TABLE I. Group A inspection. | | MIL-STD-750 [Limits | q I T I Inspection IMethod! Conditions ! LTPD ! Symbol] Min ! Max Unit ! | | | I | | I I | qT l | | | { | | | | smoot | Ph b ET {Visual and mechanical | 2071 | | | l | | | { inspection | | { | | | | | | | | | | | | | | | Saher i | fo od [Forward voltage | 4011 [Pulse method: | [Vem | --- 11.55 | v(pk) | | | [Ipq =940A( pk); | | | | | | | | [Puise width = 8.5 ms max. | | | | | | ! ! {Duty cycle = 2% max. ! ! [Reverse current | 4016 {AC method: | 1 Ipm1 | | | | | 1N3164 | 1Vpm = 200 v(pk) | | | --- {10 {tmA(pk) | | 1N3168 | ive = 400 vipk) | | J --- [10 [mA(pk) | | 1N3170 | [Ypq = 600 v(pk) | I | --- | 10 |mA(pk) | | 1N3172 | 1Vpm = 800 v(pk) | | | --- | 10 |mA(pk) | | 1N3174 | 1pm = 1000 v( pk) | | { --- [10 [mA(pk) | | 1N3175 | -~1Vpw = 1200 v(pk) | | { --- [| 10 I|mA(pk) | | 1N3176 | 1Vpu = 1400 v(pk) | | | --- [10 ImA(pk) | | 1N3177 | 1Vpw = 1600 v(pk) | l | --- | 10 [mA(pk) | | | | | | | | | | | | I | | | | | 1 [Reverse current | 4016 [AC method: | | Try | | | I {at peak reverse | | I | | | | | {voltage: | | | { | | \ i | | | | | | I | | | 1N3164 { lpy = 240 v(pk) | | [ --- 1 50 |mA(pk) | | 1N3168 | 1pqm = 480 v(pk) | | | --- | 50 [mA(pk) | | 1N3170 | 1Vpq = 720 v(pk) | | | --- [| 50 = |mA(pk) | | 1N3172 | \Vpm = 960 v(pk) | | | --- | 50 [mA(pk) | I 1N3174 | [Vay = 1200 v(pk) | | | --- {50 [mA(pk) | | 1N3175 | [Yam = 1440 v(pk) | | f --- | 50 |mA(pk) | | 1N3176 | IVpq = 1680 v( pk) | | | --- | 50 |[mA(pk) | | 1N3177 | | RM = 1920 vi pk) | | | --- | 50 Ima(pk) | | ems | pep RE {High temperature | [Tc = 175C | | | | { \ | operation: | { c | | | | | I | | | | | | | | | |Reverse current ! 4016 {AC method ! !TRM3 ! J 1N3164 | [Vay = 200 v(pk) | | | --- [ 30 [mA(pk) | | 1N3168 | 1pq = 400 v(pk) | | | --- {30 [mA(pk) | | 1N3170 | [Vey = 600 v(pk) | l | --- | 30. {mA(pk) | I 1N3172 | [Vem = 800 v(pk) | | | --- | 30 |mA(pk) | | 1N3174 { Vem = 1000 v(pk) | | | --- | 30 ImA(pk) | | 1N3175 | Iaq = 1200 v( pk) | | | --- | 30 [mA(pk) | | 1N3176 | [Vem = 1400 v(pk) | l | --- [30 [mA(pk) | ! 1N3177 ! ! RM = 1600 v(pk) ! ! --- 30 |mA(Pk) |Low temperature | ITo = -65C | | | | | { | operation: | | | | | { | | | | | | | | | | | [Reverse current 4016 {AC method ! | TRw4 ! ! ! | 1N3164 | 1pq = 200 v(pk) | | | --- { 50 {mA(pk) | | 1N3168 I 1Vpq = 400 v(pk) | | | --- [| 50 [mA(pk) | 1. 1N3170 | lpm = 600 v(pk) | l | --- | 50 [mA(pk) | | 1N3172 | |Vpq = 800 v(pk) | | {| --- | 50. |mA(pk) |MIL SPECS icf TABLE I. Group A inspection - Continued. MIL-S-19500/211/8 gooo1es 0002399 7 & Endpoint electrical measurements Subgroup 7 Not applicable I T ~ MIL-STD-750 ] T Uimits | | { | | T. | Inspection Method) Conditions ! LTPD Symbol ! Min | Max ! Unit I | | | { | | | { | qT ] | 1 | I i | | 1N3174 | 1pm = 1000 v(pk) | | { --- | 50 [mA(pk) | 1N3175 | [Vp = 1200 v(pk) | | | --- | 50 [mA(pk) | 1N3176 | IVpw = 1400 v( pk) \ | | --- [| 50 [mA(pk) 1N3177 | IVR = 1600 v(pk) ! |! --- 50 imACPk} | somes | PoP EE Not applicable | I i | | i | I I | | | | | | | Sbsrop st i | rot Not applicable | | | | | | | | | | | | | | { | Subgroup 6 |! ! ! 10 ! ! ! Surge current [4066 [Tc = 150C; | | | | | | I | l | | | { | | | { i | | I | | | | { | \ I | | | | | | | | | | { | | | | ( | | l { | | | | | I { | | | | \ | | | | | | | { { | | i | | | | | | | | | | | | | | | | | | | | | { | | | I: { | | | I | | l | | | ee ec EO TS EE ES EL NL A A er Ne 1 Vp Se =200 A de; 1/120s surges; Tec a = 6250 a(pk) 18 surge/minute; m = Ypwm (see 1.4) e table IV, steps 1 and 2MIL SPECS rCfoooo125 oonayoo T ff MIL-S-19500/211B TABLE IJ. Group B inspection. MIL-STD-750 | | Inspection T { Conditions LTPD Subgroup 1 1022 Subgroup 2 Thermal shock 1051 {temperature cycling) Hermetic seal 1071 | { I | | | { | | I | | | | | { | | | | Gross leak | Electrical See table IV, steps 1 and 2 measurements { { | | | [ l | | ! Fine Teak | | | [ | | Subgroup 3 { Blocking life OF Vem = Veun 4 Hl ; half-sine wave, Zz Electrical | i I ! measurements See table IV, steps 1 and 2 | l | l Subgroup 4 Decap-internal visual (design verification) 4 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2075 { | | Subgroup 5 | Thermal resistance Rage = 0-15 C/W Subgroup 6 Hi gn temperature life Ta = 200C non-operating) Electrical measurements Subgroup 7 Power cycling | | { | | | | | | | | | | | | | { | [See table IV, steps 1 and 2 | | |See 4.5.1: lIp = 200 A dc; IT (low) = 50 +0C,-15C IT (high) = 150 +5C,-0C IS, ,000 cycles Electrical [See table IV, steps 1, 2, and measurements 13 | | | | | | | | | | | | | | | | | | | | | | | | | { | { i | | I | | [ [ | | | | | | I | 15 10 10 11 device/O {failure for leach lot 20 10 20 I | l | | ] | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i 1 | | | | | | | | | | | | | | | | | | | |MIL-S-19500/2118 MIL SPECS icf OOO001eS 9002401 |, i TABLE III. Group C inspection. : | MIL -STD-750 ! Inspection {Wethodt Condftions LTPD | I | | | | T | I T T Subgroup 1 ! ! 15 {Physical dimensions ! 2066 |See figure 1 ! Subgroup 2 ! ! 15 ! {Thermal shock 1 1056 |Test condition B | | ! (glass strain) ! ! ! {Terminal strength | 2036 | | | | Tension (lead) | {Test condition A; | | | | [Weight = 100 1b; | | | | Its154#35 | | l l | | | Bending stress | [Test condition F; | | | (lead) | IWefght = 10 1b; | | | | It=15 43s | | I { { | | | Stud torque | ITest condition D2 | | | | [Torque = 325 Ib in.; | | | | Its15#35 I | | | | | | |Hermetic seal ! 1071 | ! | Gross leak only ! ! {Moisture resistance ! 1021 ! |External visual { 2071 ! | [Electrical | |See table IV, steps 1 and 2 | | | measurements | | | | I | | | | | Subgroup 3 i | 1 35 | Subgrou | l |Tests may be performed on de- | | | | lvices prior to the instalia- | | | | Ition of the external lead | | | | lor with the external lead | | | | | removed. I I | | | | | {Shock | 2016 (5006s | | | | | | | | | | I | |Vibration, variable | 2056 | | | ! frequency ! | | |Constant | |2500G; X1, Yj, and Yo | | acceleration | lorientations ! ! | | [Electrical | |See table IV, steps ? and 2 | | ! measurements ! ! ! Subgroup 4 15 |Salt atmosphere 1 1041 | | I ! (corrosion) -MIL SPECS rcfJ cooo1es coozyo2 3 & MIL-S-19500/211B TABLE III, Group C inspection - Continued. { q | MIL-STD-750 | Inspection {Method 1 LTPD | | | | Conditions | | | { | | | q | | T qt | | | | | Subgroup 5 | 15 | {Barometric pressure {1001 | | | (reduced) | | {1N3168, 1N3170 | {Pressure = Gm Hg I | 11N3172, 1N3174 | [Pressure = 15mm Hg | | [1N3175, 1N3176 I {Pressure = 33am Hg | | t1N3177 [Pressure = 54mm Hg [Measurement during | {See table IV, step 2 | | | test | | | | | | | | I | Subgroup 6 | [Blocking life | --- [Te = 200C; Vpw = Vw la = 10 | | I {(See 1.4) | | | | lIg = 0; half sine wave, | | | | Pe i [Electrical | [See table IV, steps 1 and2 = | | measurements ! ! 10MIL SPECS 1c 0000125 0002403 5 i MIL-$-19500/211/8 TABLE IV. Groups B, and C, endpoint electrical measurements. | -STD- Limit Istep| Inspection { MIL-STD-750 Symbol | Unit | | {Method Conditions Win [rex [ | | I I 7 | 1. [Forward voltage 4011 [Pulse method: Vem --- [1.55fv(pk) | | | | { = 940 A(pk) 1 | | | | | [Pulse width 6.5 ms max | | | | | ! { { [Duty cycle = 2% max I { ! | | | | | { 2. [Reverse current 4016 ine wethod: Rat | ! | 1N3164 Vem = 200 V(pk) --- 110 fmA(pk){ | 1N3168 Vom = 400 V(pk) --- {10 [mA(pk)! | 1N3170 View = 600 V(pk) --- 110 {fmA(pk)| | | 1N3172 | lVou = 800 V(pk) I l--- [10 {mA(pk)| | 1N3174 | [Vem = 1000 V(pk) ! [-~- [10 [mA(pk)] | 1N3175 | Ypm = 1200 V(pk) --- [10 {mA(pk)| | 1N3176 | Ypm = 1400 V(pk) --- 110 [mA(pk)] ! 1N3177 Vow = 1600 V(pk) --- 130 WmA(pk) | | ! 3. [Forward voltage {4011 Tey = 940 A(pk) laVEy wo {0.1 v(Pk) | il U8, GOVERNMENT PRINTING OFFICE; 1983-605-034/2983