UC1861-1868 UC2861-2868 UC3861-3868 Resonant-Mode Power Supply Controllers FEATURES DESCRIPTION * Controls Zero Current Switched (ZCS) The UC1861-1868 family of ICs is optimized for the control of Zero Curor Zero Voltage Switched (ZVS) rent Switched and Zero Voltage Switched quasi-resonant converters. DifQuasi-Resonant Converters ferences between members of this device family result from the various combinations of UVLO thresholds and output options. Additionally, the * Zero-Crossing Terminated One-Shot one-shot pulse steering logic is configured to program either on-time for Timer ZCS systems (UC1865-1868), or off-time for ZVS applications (UC1861* Precision 1%, Soft-Started 5V 1864). Reference The primary control blocks implemented include an error amplifier to com* Programmable Restart Delay pensate the overall system loop and to drive a voltage controlled oscillator Following Fault (VCO), featuring programmable minimum and maximum frequencies. Triggered by the VCO, the one-shot generates pulses of a programmed maxi* Voltage-Controlled Oscillator (VCO) mum width, which can be modulated by the Zero Detection comparator. with Programmable Minimum and Maximum Frequencies from 10kHz to This circuit facilitates "true" zero current or voltage switching over various line, load, and temperature changes, and is also able to accommodate the 1MHz resonant components' initial tolerances. * Low Start-Up Current (150A typical) Under-Voltage Lockout is incorporated to facilitate safe starts upon * Dual 1 Amp Peak FET Drivers power-up. The supply current during the under-voltage lockout period is typically less than 150A, and the outputs are actively forced to the low * UVLO Option for Off-Line or DC/DC state. (continued) Applications Device UVLO Outputs "Fixed" 1861 16.5/10.5 Alternating Off Time 1862 16.5/10.5 Parallel Off Time 1863 36014 Alternating Off Time 1864 36014 Parallel Off Time 1865 16.5/10.5 Alternating On Time 1866 16.5/10.5 Parallel On Time 1867 36014 Alternating On Time 1868 36014 Parallel On Time BLOCK DIAGRAM Pin numbers refer to the J and N packages. 10/98 UDG-92018 UC1861-1868 UC2861-2868 UC3861-3868 DESCRIPTION (cont.) UVLO thresholds for the UC1861/62/65/66 are 16.5V (ON) and 10.5V (OFF), whereas the UC1863/64/67/68 thresholds are 8V (ON) and 7V (OFF). After VCC exceeds the UVLO threshold, a 5V generator is enabled which provides bias for the internal circuits and up to 10mA for external usage. start delay, and the internal system reference. Each device features dual 1 Amp peak totem pole output drivers for direct interface to power MOSFETS. The outputs are programmed to alternate in the UC1861/63/65/67 devices. The UC1862/64/66/68 outputs operate in unison alllowing a 2 Amp peak current. A Fault comparator serves to detect fault conditions and set a latch while forcing the output drivers low. The SoftRef pin serves three functions: providing soft start, re- CONNNECTION DIAGRAMS ABSOLUTE MAXIMUM RATINGS PLCC-20 & LCC-20 (Top View) Q & L Package VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22V Output Current Source or Sink (Pins 11 & 14) . . . . . . . . . . . . . . . . . . . . . 0.5A DC Pulse (0.5s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5A Power Ground Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2V Inputs (Pins 2, 3, 10, & 15) . . . . . . . . . . . . . . . . . . . . -0.4 to 7V Error Amp Output Current . . . . . . . . . . . . . . . . . . . . . . . . 2mA Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W Junction Temperature (Operating). . . . . . . . . . . . . . . . . . 150C Lead Temperature (Soldering, 10 seconds) . . . . . . . . . . 300C PACKAGE PIN FUNCTION All voltages are with respect to signal ground and all currents are positive into the specified terminal. Pin numbers refer to the J and N packages. Consult Unitrode Integrated Circuits databook for information regarding thermal specifications and limitations of packages. DIL-16, SOIC-16 (Top View) J or N, DW Packages 2 FUNCTION PIN Soft Ref 5V NI INV E/A Out Sig Gnd Range RMIN CVCO RC Zero NC NC A Out Pwr Gnd Pwr Gnd VCC B Out 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 UC1861-1868 UC2861-2868 UC3861-3868 ELECTRICAL CHARACTERISTICS Unless otherwise stated, all specifications apply for -55CTA125C for the UC186x, -25CTA85C for the UC286x, and 0CTA70C for the UC386x, VCC=12V, CVCO=1nF, Range=7.15k, RMIN=86.6k, C=200pF, R=4.02k, and Csr=0.1F. TA=TJ . PARAMETER TEST CONDITIONS MIN TYP MAX UNITS 5V Generator Output Voltage Short Circuit Current Soft-Reference 12V Vcc 20V, -10mA IO 0mA VO = 0V 4.8 5.0 -150 5.2 V -15 mA Restart Delay Current V = 2V 10 20 35 A Soft Start Current V = 2V -650 -500 -350 A Reference Voltage TJ = 25C, IO = 0A 4.95 5.00 12V VCC 20V, -200A IO 200A 4.85 Line Regulation Load Regulation Error Amplifier (Note 3) 5.05 V 5.15 V 12V VCC 20V 2 20 mV -200A IO 200A 10 30 mV 10 mV Input Offset Voltage VCM = 5V, Vo = 2V, IO = 0A -10 Input Bias Current VCM = 0V -2.0 -0.3 A Voltage Gain Vcm = 5V, 0.5V VO 3.7V, IO = 0A 70 100 dB Vcm = 5V, VO = 2V, 12V VCC 20V 70 100 dB 65 Power Supply Rejection Ratio Error Amplifier (Note 3) (cont.) Common Mode Rejection Ratio 0V Vcm 6V, VO = 2V VOUT Low VID = -100mV, IO = 200A VOUT High VID = 100mV, IO = -200A 3.9 4.2 V (Note 4) 0.5 0.8 MHz VID (Error Amp) = 100mV, TJ = 25C 450 500 VID (Error Amp) = 100mV 425 VID (Error Amp) = -100mV, TJ = 25C 45 VID (Error Amp) = -100mV 42 Unity Gain Bandwidth Voltage Controlled Oscillator Maximum Frequency Minimum Frequency 100 0.17 50 dB 0.25 550 V kHz 575 kHz 55 kHz 58 kHz One Shot Zero Comparator Vth 0.45 Propagation Delay (Note 4) Maximum Pulse Width VZERO = 1V 0.50 0.55 V 120 200 ns 1000 1150 ns 2.5 4 5.5 4 5.5 7 3.8 5.5 7 25 45 ns 850 Maximum to Minimum Pulse VZERO = 0V UCx861 - UCx864 Width Ratio VZERO = 0V UCx865 - UCx868. -55C to +85C VZERO = 0V UCx865 - UCx868, +125C Output Stage Rise and Fall Time CLOAD = 1nF (Note 4) Output Low Saturation IO = 20mA 0.2 0.5 V IO = 200mA 0.5 2.2 V Output High Saturation UVLO Low Saturation Fault Comparator IO = -200mA, down from Vcc 1.7 2.5 V IO = 20mA 0.8 1.5 V 3.00 3.15 V 100 200 ns Fault Comparator Vth Delay to Output 2.85 (Note 4) (Note 5) 3 UC1861-1868 UC2861-2868 UC3861-3868 ELECTRICAL CHARACTERISTICS Unless otherwise stated, all specifications apply for -55CTA125C for the UC186x, -25CTA85C for the UC286x, and 0CTA70C for the UC386x, VCC=12V, CVCO=1nF, Range=7.15k, RMIN=86.6k, C=200pF, R=4.02k, and Csr=0.1F. TA=TJ . PARAMETER TEST CONDITIONS MIN TYP MAX UNITS UVLO Vcc Turn-on Threshold UCx861, UCx862, UCx865, UCx866 15 16.5 18 V UCx863, UCx864, UCx867, UCx868 7 8.0 9 V Vcc Turn-off Threshold UCx861, UCx862, UCx865, UCx866 9.5 10.5 11.5 V UCx863, UCx864, UCx867, UCx868 6 7.0 8 V Icc Start VCC = VCC(on) - 0.3V 150 300 A Icc Run VID = 100mV 25 32 mA Note 1: Currents are defined as positive into the pin. Note 2: Pulse measurement techniques are used to insure that TJ = TA. Note 3: VID = V(NI) - V(INV). Note 4: This parameter is not 100% tested in production but guaranteed by design. Note 5: Vi = 0 to 4V tr(Vi) 10ns tpd = t(Vo = 6V) - t(Vi = 3V) APPLICATION INFORMATION UVLO & 5V GENERATOR (See Figure 1): When power is applied to the chip and Vcc is less than the upper UVLO threshold, Icc will be less than 300A, the 5V generator will be off, and the outputs will be actively held low. The fault pin is input to a high speed comparator with a threshold of 3V. In the event of a detected fault, the fault latch is set and the outputs are driven low. If Soft-Ref is above 4V, the delay latch is set. Restart delay is timed as Soft-Ref is discharged by 20A. When Soft-Ref is fully discharged, the fault latch is reset if the fault input signal is low. The Fault pin can be used as a system shutdown pin. When Vcc exceeds the upper UVLO threshold, the 5V generator turns on. Until the 5V pin exceeds 4.9V, the outputs will still remain low. The 5V pin should be bypassed to signal ground with a 0.1F capacitor. The capacitor should have low equivalent series resistance and inductance. If a fault is detected during soft-start, the fault latch is set and the outputs are driven low. The delay latch will remain reset until Soft-Ref charges to 4V. This sets the delay latch, and restart delay is timed. Note that restart delay for a single fault event is longer than for recurring faults since Soft-Ref must be discharged from 5V instead of 4V. FAULT AND SOFT-REFERENCE (See Figure 1): The Soft-Ref pin serves three functions: system reference, restart delay, and soft-start. Designed to source or sink 200A, this pin should be used as the input reference for the error amplifier circuit. This pin requires a bypass capacitor of at least 0.1F. This yields a minimum soft-start time of 1ms. The restart delay to soft-start time ratio is 24:1 for a fault occurring during normal operation and 19:1 for faults occurring during soft-start. Shorter ratios can be programmed down to a limit of approximately 3:1 by the addition of a 20k or larger resistor from Soft-Ref to ground. Under-Voltage Lockout sets both the fault and restart delay latches. This holds the outputs low and discharges the Soft-Ref pin. After UVLO, the fault latch is reset by the low voltage on the Soft-Ref pin. The reset fault latch resets the delay latch and Soft-Ref charges via the 0.5mA current source. A 100k resistor from Soft-Ref to 5V will have the effect of permanent shut down after a fault since the internal 20A current source can't pull Soft-Ref low. This feature can be used to require recycling Vcc after a fault. Care must be taken to insure Soft-Ref is indeed low at start up, or the fault latch will never be reset. 4 UC1861-1868 UC2861-2868 UC3861-3868 APPLICATION INFORMATION UDG-92020 UDG-92021-1 Figure 1. UVLO, 5V, fault and soft-ref. 5 UDG-92022-1 UDG-92023-1 Figure 2. Error Amp, Voltage Controlled Oscillator, and One Shot 6 UC1861-1868 UC2861-2868 UC3861-3868 APPLICATION INFORMATION The Error Amplifier directly controls the oscillator frequency. E/A output low corresponds to minimum frequency and output high corresponds to maximum frequency. At the end of each oscillator cycle, the RC pin is discharged to one diode drop above ground. At the beginning of the oscillator cycle, V(RC) is less than Vth1 and so the output of the zero detect comparator is ignored. After V(RC) exceeds Vth1, the one shot pulse will be terminated as soon as the zero pin falls below 0.5V or V(RC) exceeds Vth2. The minimum one shot pulse width is approximately given by the equation: Minimum oscillator frequency is set by Rmin and Cvco. The minimum frequency is approximately given by the equation: FMIN 43 . RMIN * CVCO Maximum oscillator frequency is set by Rmin, Range & Cvco. The maximum frequency is approximately given by the equation: FMAX (RMIN 3.3 / / Range ) * CVCO Tpw(min) 0.3 R C. The maximum pulse width is approximately given by: Tpw(max) 1.2 R C. STEERING LOGIC UDG-92014 UDG-92013 The steering logic is configured on the UC1861,63 to result in dual non-overlapping square waves at outputs A & B. This is suited to drive dual switch ZVS systems. The steering logic is configured on the UC1862,64 to result in inverted pulse trains occurring identically at both output pins. This is suited to drive single switch ZVS systems. Both outputs are available to drive the same MOSFET gate. It is advisable to join the pins with 0.5 ohm resistors. UDG-92015 The steering logic is configured on the UC1865,67 to result in alternating pulse trains at outputs A & B. This is suited to drive dual switch ZCS systems. UDG-92016 The steering logic is configured on the UC1866,68 to result in non-inverted pulse trains occurring identically at both output pins. This is suited to drive single switch ZCS systems. Both outputs are available to drive the same MOSFET gate. It is advisable to join the pins with 0.5 ohm resistors. 7 UC1861-1868 UC2861-2868 UC3861-3868 APPLICATION INFORMATION (cont.) UDG-92017 Figure 3. Current waveforms. UNITRODE CORPORATION 7 CONTINENTAL BLVD. * MERRIMACK, NH 03054 TEL. (603) 424-2410 * FAX (603) 424-3460 8 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated