LM301A, LM201A, LM201AV Non Compensated Single Operational Amplifiers A general purpose operational amplifier that allows the user to choose the compensation capacitor best suited to his needs. With proper compensation, summing amplifier slew rates to 10 V/ms can be obtained. http://onsemi.com Features MARKING DIAGRAMS * Low Input Offset Current: 20 nA Maximum Over Temperature * * * * * Range External Frequency Compensation for Flexibility Class AB Output Provides Excellent Linearity Output Short Circuit Protection Guaranteed Drift Characteristics Pb-Free Packages are Available 8 LMx01AN AWL YYWWG PDIP-8 N SUFFIX CASE 626 8 1 1 VEE Inverting Input 8 VCC NonInverting Input Output 1 + 1 5.1 MW 30 pF 10 MW 8 Balance Freq Compen Balance 20 k LM201AVDR2G 8 VEE 1 Figure 1. Standard Compensation and Offset Balancing Circuit VUT SOIC-8 D SUFFIX CASE 751 x A WL, L YY, Y WW, W G G VCC LMx01 ALYWA G 201AV ALYW G = 2 or 3 = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package = Pb-Free Package + VO VI PIN CONNECTIONS MZ4622 or Equiv. VEE VCC 3.9 V Balance Inputs VO VLT VEE VEE VO = 4.8 V for VLT VI VUT VO = -0.4 V VI < VLT or VI > VUT 1 8 Compensation 2 7 VCC 3 6 Output 4 5 Balance (Top View) (Pins Not Shown Are Not Connected) Figure 2. Double-Ended Limit Detector ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. (c) Semiconductor Components Industries, LLC, 2011 December, 2011 - Rev. 11 1 Publication Order Number: LM301A/D LM301A, LM201A, LM201AV Balance Compensation VCC Inputs + 500 25 Output 50 450 40k 5k 20 k 250 40k 10 k 80 k 1.0 k VEE Balance Figure 3. Representative Circuit Schematic ORDERING INFORMATION Package Shipping LM301ADG SOIC-8 (Pb-Free) 98 Units/Rail LM301ADR2G SOIC-8 (Pb-Free) 2500 Tape & Reel PDIP-8 50 Units/Rail LM301ANG PDIP-8 (Pb-Free) 50 Units/Rail LM201ADG SOIC-8 (Pb-Free) 98 Units/Rail LM201ADR2G SOIC-8 (Pb-Free) 2500 Tape & Reel Device LM301AN LM201AN PDIP-8 50 Units/Rail LM201ANG PDIP-8 (Pb-Free) 50 Units/Rail LM201AVDR2G SOIC-8 (Pb-Free) 2500 Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 LM301A, LM201A, LM201AV MAXIMUM RATINGS Value Rating Power Supply Voltage Symbol LM201A LM201AV LM301A Unit VCC, VEE 22 22 18 Vdc Input Differential Voltage VID 30 V Input Common Mode Range (Note 1) VICR 15 V Output Short Circuit Duration tSC Continuous Power Dissipation (Package Limitation) PD Plastic Dual-In-Line Package 625 625 625 mW Derate above TA = +25C 5.0 5.0 5.0 mW/C -40 to +105 0 to +70 C Operating Ambient Temperature Range TA Storage Temperature Range Tstg -25 to +85 -65 to +150 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted.) Unless otherwise specified, these specifications apply for supply voltages from 5.0 V to 20 V for the LM201A and LM201AV, and from 5.0 V to 15 V for the LM301A. LM201A / LM201AV LM301A Symbol Min Typ Max Min Typ Max Unit Input Offset Voltage (RS 50 kW) VIO - 0.7 2.0 - 2.0 7.5 mV Input Offset Current IIO - 1.5 10 - 3.0 50 nA Input Bias Current IIB - 30 75 - 70 250 nA Input Resistance ri 1.5 4.0 - 0.5 2.0 - MW - - 1.8 - 3.0 - - - - 1.8 - 3.0 50 160 - 25 160 - V/mV - 3.0 - - 10 mV Characteristic Supply Current VCC/VEE = 20 V VCC/VEE = 15 V Large Signal Voltage Gain (VCC/VEE = 15 V, VO = 10 V, RL > 2.0 kW) ICC,IEE AV mA The following specifications apply over the operating temperature range. Input Offset Voltage (RS 50 kW) Input Offset Current VIO - IIO - - 20 - - 70 nA Avg Temperature Coefficient of Input Offset Voltage (Note 2) TA(min) TA TA (max) DVIO/DT - 3.0 15 - 6.0 30 mV/C Avg Temperature Coefficient of Input Offset Current (Note 2) +25C TA TA (max) TA(min) TA 25C DIIO/DT nA/C - - 0.01 0.02 0.1 0.2 - - 0.01 0.02 0.3 0.6 IIB - - 100 - - 300 nA Large Signal Voltage Gain (VCC/VEE = 15 V, VO = 10V, RL > 2.0 kW) AVOL 25 - - 15 - - V/mV Input Voltage Range VCC/VEE = 20 V VCC/VEE = 15 V VICR -15 - - - +15 - - -12 - - - +12 Common Mode Rejection (RS 50 kW) CMR 80 96 - 70 90 - dB Supply Voltage Rejection (RS 50 kW) PSR 80 96 - 70 96 - dB VO 12 10 14 13 - - 12 10 14 13 - - V ICC,IEE - 1.2 2.5 - - - mA Input Bias Current Output Voltage Swing (VCC/VEE = 15 V, RL = 10 kW, RL > 2.0 kW) Supply Currents (TA = TA(max), VCC/VEE = 20 V) V 1. For supply voltages less than 15 V, the absolute maximum input voltage is equal to the supply voltage. 2. Guaranteed by design. http://onsemi.com 3 LM301A, LM201A, LM201AV Applicable to the Specified Operating Temperature Ranges 16 VOR, OUTPUT VOLTAGE RANGE ( V) VIR , INPUT VOLTAGE RANGE (V) 20 12 LM201A only Positive 8.0 Negative 4.0 0 0 5.0 10 15 VCC, ( -VEE), SUPPLY VOLTAGE (V) 20 Applicable to the Specified Operating Temperature Ranges 16 12 Minimum RL = 10 k 8.0 Minimum RL = 2.0 k 4.0 0 20 0 Figure 4. Minimum Input Voltage Range 5.0 10 15 VCC, ( -VEE), SUPPLY VOLTAGE (V) 20 Figure 5. Minimum Output Voltage Swing 100 2.5 I CC , I EE , SUPPLY CURRENTS (mA) Applicable to the Specified Operating Temperature Ranges 94 A V , VOLTAGE GAIN (dB) LM201A only 88 LM201A only 82 76 2.0 1.5 5.0 10 15 TA = +25C 0.5 70 0 LM201A only 1.0 0 20 0 5.0 10 15 VCC, ( -VEE), SUPPLY VOLTAGE (V) VCC, ( -VEE), SUPPLY VOLTAGE (V) Figure 6. Minimum Voltage Gain Figure 7. Typical Supply Currents 20 Single-Pole Compensation A V , VOLTAGE GAIN (dB) 160 140 315 120 270 100 80 C1 = 3.0 pF 225 Phase 180 60 135 C1 = 30 pF 40 20 0 -20 1.0 90 0 10 100 1.0 k 10 k 100 k 1.0 M Single-Pole Compensation 15 10 C1 = 3.0 pF 5.0 45 Gain VOR, OUTPUT VOLTAGE RANGE ( V) 180 C1 = 30 pF 0 1.0 k 10 M 10 k 100 k 1.0 M 10 M f, FREQUENCY (Hz) f, FREQUENCY (Hz) Figure 8. Open Loop Frequency Response Figure 9. Large Signal Frequency Response http://onsemi.com 4 LM301A, LM201A, LM201AV 140 8.0 6.0 4.0 2.0 Input 0 -2.0 Output -4.0 -6.0 100 225 80 180 Phase 60 135 40 90 20 45 Gain 0 0 0 -8.0 -10 0 10 20 30 40 50 60 70 80 -20 10 90 100 1.0 k 10 k 100 k 1.0 M 10 M 100 M t, TIME (ms) f, FREQUENCY (Hz) Figure 10. Voltage Follower Pulse Response Figure 11. Open Loop Frequency Response 10 VOR, OUTPUT VOLTAGE RANGE ( V) 18 VOR, OUTPUT VOLTAGE RANGE ( V) Feedforward Compensation 120 PHASE LAG (DEGREES) Single-Pole Compensation A V, VOLTAGE GAIN (dB) VIR , VOR, VOLTAGE RANGE ( V) 10 Feedforward Compensation 16 12 8.0 4.0 0 100 k Feedforward Compensation 8.0 Output 6.0 4.0 2.0 Input 0 -2.0 -4.0 -6.0 -8.0 -10 1.0 M f, FREQUENCY (Hz) 10 M 0 Figure 12. Large Signal Frequency Response 1.0 2.0 3.0 4.0 5.0 t, TIME (ms) 6.0 7.0 8.0 Figure 13. Inverter Pulse Response C2 R2 R1 -VI R2 VCC 2 R1 6 R3 +VI 7 3 VI VO C1 C1 4 + 8 Frequency Compensation 1 R3 R1 Cs R1 +R2 C1 150 pF Cs = 30 pF VCC 6 3 + 4 1 VEE Balance 7 2 VO VEE Balance C2 = 1 2foR2 fo = 3.0 MHz Figure 14. Single-Pole Compensation Figure 15. Feedforward Compensation http://onsemi.com 5 9.0 LM301A, LM201A, LM201AV PACKAGE DIMENSIONS 8 LEAD PDIP CASE 626-05 ISSUE M D A D1 E 8 5 E1 1 4 NOTE 5 F c E2 END VIEW TOP VIEW NOTE 3 e/2 A L A1 C SEATING PLANE E3 e 8X SIDE VIEW b 0.010 M C A END VIEW http://onsemi.com 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSION E IS MEASURED WITH THE LEADS RESTRAINED PARALLEL AT WIDTH E2. 4. DIMENSION E1 DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A A1 b C D D1 E E1 E2 E3 e L INCHES NOM MAX ---- 0.210 ---- ---- 0.018 0.022 0.010 0.014 0.365 0.400 ---- ---- 0.310 0.325 0.250 0.280 0.300 BSC ---- ---- 0.430 0.100 BSC 0.115 0.130 0.150 MIN ---- 0.015 0.014 0.008 0.355 0.005 0.300 0.240 MILLIMETERS MIN NOM MAX ---- ---- 5.33 0.38 ---- ---- 0.35 0.46 0.56 0.20 0.25 0.36 9.02 9.27 10.02 0.13 ---- ---- 7.62 7.87 8.26 6.10 6.35 7.11 7.62 BSC ---- ---- 10.92 2.54 BSC 2.92 3.30 3.81 LM301A, LM201A, LM201AV PACKAGE DIMENSIONS SOIC-8 NB CASE 751-07 ISSUE AK -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 0.25 (0.010) M Y M 1 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X S M J SOLDERING FOOTPRINT* MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative LM301A/D