STB3N62K3, STD3N62K3, STF3N62K3 STP3N62K3, STU3N62K3 N-channel 620 V, 2.2 , 2.7 A SuperMESH3TM Power MOSFET D2PAK, DPAK, TO-220FP, TO-220, IPAK Features Type STB3N62K3 STD3N62K3 STF3N62K3 STP3N62K3 STU3N62K3 VDSS RDS(on) max ID PD 620 V 620 V 620 V 620 V 620 V < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 2.7 A 2.7 A 2.7 A(1) 2.7 A 2.7 A 45 W 45 W 20 W 45 W 45 W 3 3 2 1 1 DPAK IPAK 3 1 DPAK 1. Limited by package 3 1 100% avalanche tested Extremely high dv/dt capability Very low intrinsic capacitances Improved diode reverse recovery characteristics Zener-protected TO-220 Figure 1. 3 2 1 2 TO-220FP Internal schematic diagram Application Switching applications Description The new SuperMESH3TM series is obtained through the combination of a further fine tuning of ST's well established strip-based PowerMESHTM layout with a new optimization of the vertical structure. In addition to reducing on-resistance significantly versus previous generation, special attention has been taken to ensure a very good dv/dt capability and higher margin in breakdown voltage for the most demanding application. Table 1. Device summary Order codes Marking Package Packaging STB3N62K3 3N62K3 DPAK Tape and reel STD3N62K3 3N62K3 DPAK Tape and reel STF3N62K3 3N62K3 TO-220FP Tube STP3N62K3 3N62K3 TO-220 Tube STU3N62K3 3N62K3 IPAK Tube August 2009 Doc ID 14894 Rev 2 1/20 www.st.com 20 Contents STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ......................... 7 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Doc ID 14894 Rev 2 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter TO-220 DPAK DPAK IPAK VDS Drain-source voltage (VGS = 0) 620 VGS Gate- source voltage 30 ID ID Drain current (continuous) at TC = 25 C Unit TO-220FP V 2.7 V 2.7 (1) A (1) A Drain current (continuous) at TC = 100 C 1.7 1.7 IDM (2) Drain current (pulsed) 10.8 10.8(1) A PTOT Total dissipation at TC = 25 C 45 20 W 0.36 0.16 W/C Derating factor VESD(G-S) dv/dt (3) Gate source ESD (HBM-C = 100 pF, R = 1.5 k) Peak diode recovery voltage slope VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t = 1 s; TC = 25 C) Tstg Storage temperature Tj 2500 V 9 V/ns -- 2500 V -55 to 150 C 150 C Max. operating junction temperature 1. Limited by package 2. Pulse width limited by safe operating area 3. ISD 2.7 A, di/dt 200 A/s, VDD = 80% V(BR)DSS Table 3. Symbol Thermal data Parameter Rthj-case Thermal resistance junction-case max Rthj-pcb Thermal resistance junction-pcb max Rthj-amb Thermal resistance junction-amb max Tl TO-220 DPAK DPAK IPAK TO-220FP 2.78 -- Maximum lead temperature for soldering purpose Doc ID 14894 Rev 2 50 62.5 -100 300 Unit 6.25 C/W -- C/W 62.5 C/W C 3/20 Electrical ratings Table 4. 4/20 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Avalanche characteristics Symbol Parameter Max value Unit IAR Avalanche current, repetitive or not-repetitive (pulse width limited by Tj max) 2.7 A EAS Single pulse avalanche energy (starting Tj = 25 C, ID = IAR, VDD = 50 V) 100 mJ Doc ID 14894 Rev 2 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 2 Electrical characteristics Electrical characteristics (TC = 25 C unless otherwise specified) Table 5. Symbol V(BR)DSS On /off states Parameter Test conditions Drain-source breakdown voltage ID = 1 mA, VGS = 0 IDSS VDS = Max rating Zero gate voltage drain current (VGS = 0) VDS = Max rating, TC=125 C IGSS Gate-body leakage current (VDS = 0) Gate threshold voltage VDS = VGS, ID = 50 A RDS(on Static drain-source on resistance Symbol Typ. Max. Unit 620 V 1 50 A A 10 A 3.75 4.5 V 2.2 2.5 Min. Typ. Max. Unit VGS = 20 V VGS(th) Table 6. Min. 3 VGS = 10 V, ID = 1.4 A Dynamic Parameter Test conditions Forward transconductance VDS = 15 V, ID = 1.4 A - 2.1 - S Input capacitance Output capacitance Reverse transfer capacitance VDS = 25 V, f = 1 MHz, VGS = 0 - 385 55 6 - pF pF pF Equivalent output capacitance VGS = 0, VDS = 0 to 496 V - 32.3 - pF RG Intrinsic gate resistance f = 1 MHz open drain - 10 - Qg Qgs Qgd Total gate charge Gate-source charge Gate-drain charge VDD = 496 V, ID = 2.7 A, VGS = 10 V (see Figure 17) - 13 2.5 7.5 - nC nC nC gfs (1) Ciss Coss Crss COSS eq(1) 1. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS Table 7. Symbol td(on) tr td(off) tf Switching times Parameter Turn-on delay time Rise time Turn-off-delay time Fall time Test conditions VDD = 310 V, ID =1.7 A, RG = 4.7 , VGS = 10 V (see Figure 16) Doc ID 14894 Rev 2 Min. Typ. - 9 6.8 22 15.6 Max Unit - ns ns ns ns 5/20 Electrical characteristics Table 8. STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Source drain diode Symbol Parameter ISD ISDM (1) Source-drain current Source-drain current (pulsed) VSD (2) Forward on voltage trr Qrr IRRM trr Qrr IRRM Test conditions Min. Typ. Max. Unit - 2.7 10.8 A A ISD = 2.7 A, VGS = 0 - 1.6 V Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 2.7 A, di/dt = 100 A/s VDD = 60 V (see Figure 21) - 190 825 9 ns nC A Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 2.7 A, di/dt = 100 A/s VDD = 60 V, Tj = 150 C (see Figure 21) - 255 1100 10 ns nC A Min Typ 1. Pulse width limited by safe operating area 2. Pulsed: Pulse duration = 300 s, duty cycle 1.5% Table 9. Symbol BVGSO(1) Gate-source Zener diode Parameter Test conditions Gate-source breakdown voltage Igs= 1 mA (open drain) Max Unit 30 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device's ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device's integrity. These integrated Zener diodes thus avoid the usage of external components 6/20 Doc ID 14894 Rev 2 V STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Electrical characteristics 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220, IPAK, DPAK, DPAK Figure 3. Thermal impedance for TO-220, IPAK, DPAK, DPAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP Figure 6. Output characteristics Figure 7. Transfer characteristics Doc ID 14894 Rev 2 7/20 Electrical characteristics Figure 8. STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Normalized BVDSS vs temperature Figure 9. Static drain-source on resistance Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations Figure 12. Normalized gate threshold voltage vs temperature 8/20 Figure 13. Normalized on resistance vs temperature Doc ID 14894 Rev 2 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Figure 14. Source-drain diode forward characteristics Electrical characteristics Figure 15. Maximum avalanche energy vs temperature Doc ID 14894 Rev 2 9/20 Test circuits 3 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Test circuits Figure 16. Switching times test circuit for resistive load Figure 17. Gate charge test circuit Figure 18. Test circuit for inductive load Figure 19. Unclamped Inductive load test switching and diode recovery times circuit Figure 20. Unclamped inductive waveform 10/20 Figure 21. Switching time waveform Doc ID 14894 Rev 2 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 14894 Rev 2 11/20 Package mechanical data STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 P Q 12/20 Typ 4.40 0.61 1.14 0.48 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Doc ID 14894 Rev 2 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Package mechanical data TO-220FP mechanical data mm. Dim. Min. A 4.40 inch Typ Max. Min. 4.60 0.173 Typ. 0.181 Max. B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.017 0.027 F 0.75 1.00 0.030 0.039 F1 1.15 1.50 0.045 0.067 F2 1.15 1.50 0.045 0.067 G 4.95 5.20 0.195 0.204 G1 2.40 2.70 0.094 0.106 H 10 10.40 0.393 L2 16 0.409 0.630 28.6 30.6 1.126 L4 9.80 10.60 0.385 1.204 0.417 L5 2.9 3.6 0.114 0.141 L6 15.90 16.40 0.626 0.645 L7 9 9.30 0.354 0.366 Dia 3 3.2 0.118 0.126 B D A E L3 L3 L6 F2 H G G1 Dia F F1 L7 L2 L5 1 2 3 L4 7012510-I Doc ID 14894 Rev 2 13/20 Package mechanical data STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 TO-251 (IPAK) mechanical data mm. DIM. min. typ max. A 2.20 2.40 A1 0.90 1.10 b 0.64 0.90 b2 0.95 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 E 6.40 6.60 e e1 2.28 4.40 4.60 H 16.10 L 9.00 9.40 (L1) 0.80 1.20 L2 0.80 V1 10 o 0068771_H 14/20 Doc ID 14894 Rev 2 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Package mechanical data TO-252 (DPAK) mechanical data DIM. mm. min. typ max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1 L1 2.80 L2 L4 0.80 0.60 1 R V2 0.20 8o 0o 0068772_G Doc ID 14894 Rev 2 15/20 Package mechanical data STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 DPAK (TO-263) mechanical data mm inch Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 Typ 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 Max Min 4.60 0.23 0.93 1.70 0.60 1.36 9.35 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334 10.40 2.54 4.88 15 2.49 2.29 1.27 1.30 0.192 0.590 0.099 0.090 0.05 0.051 8 0 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.208 0.624 0.106 0.110 0.055 0.069 0.016 0079457_M 16/20 Max 0.1 5.28 15.85 2.69 2.79 1.40 1.75 0.4 0 Typ Doc ID 14894 Rev 2 8 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 5 Package mechanical data Package mechanical data DPAK FOOTPRINT All dimensions are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 B1 D 1.5 D1 1.5 E 1.65 MIN. 12.1 0.476 1.6 0.059 0.063 1.85 0.065 0.073 7.4 7.6 0.291 0.299 2.55 2.75 0.100 0.108 0.153 0.161 P0 3.9 4.1 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 0.075 0.082 40 15.7 MAX. 330 12.992 13.2 0.504 0.520 18.4 0.645 0.724 0.059 0.795 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 0.059 F R MIN. MAX. K0 W inch MAX. 1.574 16.3 0.618 0.641 Doc ID 14894 Rev 2 17/20 Package mechanical data STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 MAX. B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 18/20 Doc ID 14894 Rev 2 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 6 Revision history Revision history Table 10. Document revision history Date Revision Changes 10-Jul-2008 1 First release 17-Aug-2009 2 Modified: marking of the Table 1 Doc ID 14894 Rev 2 19/20 STB3N62K3, STD3N62K3, STF3N62K3, STP3N62K3, STU3N62K3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 14894 Rev 2