SF2145B * SAW Filter, 895 MHz, 15 MHz BW * 7.0 X 5.0 mm 10 pin Surface-Mount Case * Complies with Directive 2002/95/EC (RoHS) 895 MHz SAW Filter Pb Absolute Maximum Ratings Rating Maximum Incident Power in Passband Maximum DC Voltage Between any Two Terminals Operating Temperature Range Value Units +20 dBm 0 VDC -20 to +70 C SMP-03 Electrical Characteristics Characteristic Sym Notes fC 1 Min Typ Max Units 895 MHz Source Impedance, single ended 50 Load Impedance, single ended 50 Center Frequency 1 dB Bandwidth 18 IL Insertion Loss, 894 to 895.5 MHz Insertion Loss Variation: 8.5 Any point within 894 to 895.5 MHz measured at a constant temperature with the RF input level varying from +10 to +20 dBm Amplitude Ripple, 894 to 895.5 MHz Average Group Delay, 894 to 895.5 MHz 804 Group Delay Variation, 894.0 to 895.5 MHz Input / Output Return Loss at fC 10 Temperature Coefficient Case Style MHz 9.0 dB 0.3 dB dB .35 .75 814 824 ns 10 25 nsP-P 15 dB -18 ppm/K SMP-03 7.0 x 5.0 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM SF2145B YYWW CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. 5. 6. 7. 8. The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc., are registered trademarks of RF Monolithics, Inc. Page 1 of 5 SF2145B - 7/9/09 Tesing Environment 3 8 Note: Unmatched Filter to 50 Input / Output. 18 Feb 2008 13:27:10 CH1 S11 1 U FS 1 : 60 . 025 -1 . 6348 899 . 700 000 MHz SF2145B DEMO 108 . 21 CH3 S22 1 : 55 . 941 899 . 700 000 pF 1 U FS -5 . 0742 MHz 34 . 862 pF DEVICE # 49 1 1 PRm Cor Cor Full CENTR CH2 899 . 700 S21 MHz LOG SPAN 50 . 000 1 dB/ CENTR MHz 899 . 700 1 : 0 . 0000 REF -10 dB MHz SPAN dB 0 . 000 50 . 000 000 MHz MHz 1 CH2 Max BW : Cor Markers REF=1 26 . 232706 MHz 900 . 034584 MHz 2 Full cent : Q: 34 . 310 PRm 1_ loss 3 CENTER www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. 899 . 700 000 : -7 . 7333 dB 4 MHz SPAN 50 . 000 000 MHz Page 2 of 5 SF2145B - 7/9/09 18 Feb 2008 13:26:55 CH1 S21 DEL 100 ns/ REF 800 ns 2 : 667 . 57 ps 1 . 500 000 MHz SF2145B DEMO DEVICE # 49 2 CH1 Smo mean Markers REF=1 : 812 . 88 ns s . dev : 1 . 2799 ns p-p : 4 . 4631 ns 1 Cor PRm Resp CH2 S21 LOG 1 dB/ REF -10 dB 2 : . 11980 dB 1 . 500 000 MHz 2 CH2 Cor Resp 1 Markers REF=1 mean : -8 . 0196 dB s . dev : . 06000 dB p-p : . 24780 dB PRm CH2 CENTER www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. 899 . 700 000 MHz SPAN 50 . 000 000 MHz Page 3 of 5 SF2145B - 7/9/09 Tape and Reel Specifications "B" REF. 100 REF. "B " Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 16.0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 4 of 5 SF2145B - 7/9/09 SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions Dimension Min A B C D E H J K P Recommended PCB Footprint 6.80 4.80 .47 2.41 0.87 4.87 2.87 1.14 mm Nom Max Min 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 0.268 0.189 Electrical Connections Connection 0.019 0.095 0.034 0.192 0.113 0.045 Inches Nom Max 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 Terminals Input (Port 1) 3 Output (Port 2) 8 Case Ground 2, 4, 7, 9 To Be Grounded 1, 2, 4, 5, 6, 7, 9, 10 Materials Solder Pad Plating 0.3 to 1.0 m Gold over 1.27 to 8.89 m Nickel Lid Plating 2.0 to 3.0 m Nickel Body Al2O3 Ceramic Pb Free C B E H H A J D P K www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 5 of 5 SF2145B - 7/9/09