1408463-1 - Tyco Electronics

Product

Specification 108-2087

12Nov03 Rev A

EC 0990-1543-03

QMA (Snap-On Mating Style Coaxial Connector)

Harrisburg, PA

All International Rights Reserved.

* Trademark

| Indi cates ch ange For la test revisio n call AMP FAX*/Product Info numbe r 1-800-522-6752.

For Regional Customer Service, visit our website at www.tycoelectronics.com 1 of 5

LOC B

1. SCOPE

1.1. Content

This specificati on covers performance, tests and qualit y r equirements for the T yco Electronics QMA

snap-on mating style coax ial connect or. This connector mates w hen finger s on the outer contact of the

pl ug snap over a step on the jack housing. Pul ling back on t he outer housing of the plug opens the

fingers which r eleases the connector .

1.2. Qualification

When tests are per formed on the subject product line, procedures specified in Figure 1 shall be used.

Al l inspections shall be performed using the applicable inspection plan and pr oduct drawing.

1.3. Qual ification Test Results

Successful qualificati on testing on the subject product line was complet ed on 26Sep03. T he

Qual ification Test Repor t number for this testing is 501-572. This documentation is on f ile at and

available from Engineering Pr actices and St andards ( EPS).

2. APPLICABLE DOCUM ENTS

The following documents f orm a part of this specif icati on to the ext ent specif ied herein. Unless otherw ise

speci fied, the latest edition of the document applies. In the event of conflict betw een the requirements of

this specification and the product dr awing, the product drawing shall t ake precedence. In the event of

conflict betw een the requirements of this specif icati on and the r eferenced documents, this specif icati on

shal l take precedence.

2.1. Tyco Elect ronics Documents

109-197: AMP Test Specifications vs EIA and IEC Test Methods

501-572: Qual ification Test Repor t

2.2. Commercial Standard

EIA- 364: El ectr ical Connect or/Socket T est Pr ocedures Including Envi ronmental Classifications

3. REQUIREMENTS

3.1. Desi gn and Constr uction

Product shall be of the design, construction and physical dimensions specifi ed on the applicable product

drawing.

3.2. Materials

Materials used in the construction of this product shall be as specified on the appl icable pr oduct dr awing.

108-2087

Rev A 2 of 5

3.3. Ratings

Vol tage: 335 volts AC

Temperature: -40 t o 80

. Charact eristic Impedance: 50 ohms

. Frequency Range: DC to 6000 MHz

3.4. Perf ormance and Test Description

Product is designed t o meet the elect rical, mechanical and environmental per formance requirements

speci fied in Figure 1. Unless ot herwise specified, all t ests shall be performed at ambient environmental

condi tions per EIA-364.

3.5. Test Requirements and Procedur es Summary

Test Descripti on Requi rement Procedur e

Initial examinat ion of product . Meets requirements of pr oduct

drawing. EIA-364-18.

Vi sual and dimensional ( C of C)

i nspection per product draw ing.

Fi nal examination of product. Meets visual requi rements. EIA- 364-18.

Vi sual inspection.

ELECTRICAL

Low level contact resistance. 5 milliohms maximum for center

contact.

2.5 milliohms maximum for outer

contact.

EIA-364-23.

Subject specimens to 100

milliamperes maximum and 20

millivolts maximum open cir cuit

voltage.

Vol tage st anding wave ratio. 1.15 maximum for straight product .

1.22 maximum for right angle

product.

Not applicable to PWB product.

EIA-364-108.

Measure VSWR between 0 and

6000 MH z.

Insulation resistance. 5000 megohms minimum. EIA- 364-21.

Test between adjacent contacts.

Wi thstanding voltage. 1 minut e hold wit h no breakdow n or

flashover. EIA-364-20,

Condi tion I.

750 volts AC at sea level for RG

316 and RD 316 cabl e connector s.

1000 volts AC at sea level for

adapter s, receptacles, RG 58, RG

400 and .141 semi -r igid connect ors.

Test between adjacent contacts.

RF i nsert ion loss. .25 dB maximum.

Not applicable to PWB product. EIA-364-101,

Method A.

Measure RF inser tion loss at 6000

MHz.

MECHANICAL

Solderability, dip test. Solderable area shall have a

minimum of 95% sol der coverage. EIA-364-52,

Categor y 3.

Subject contacts to solderability.

Fi gure 1 ( cont)

108-2087

Test Descripti on Requi rement Procedur e

Rev A 3 of 5

Vi brat ion, random. No discontinuit ies of 1 micr osecond

or longer duration.

See Note.

EIA-364-28,

Test Condition VII,

Condi tion D.

Subject mated specimens to 3.10

G's rms between 20-500 Hz. 15

minut es in each of 3 mutual ly

perpendicular planes.

Mechanical shock. No di scontinuities of 1 microsecond

or longer duration.

See Note.

EIA-364-27,

Method H.

Subject mated specimens to 30 G's

hal f- sine shock pulses of 11

milliseconds durat ion. 3 shocks i n

each di rect ion applied along 3

mutual ly perpendicular planes, 18

tot al shocks.

Durability. See Note. EIA-364-9.

Mate and unmate specimens for

100 cycles at a maxi mum rate of

500 cycles per hour.

Int erface retention f orce. 60 N minimum wi thout pulling the

release ring on the plug. EIA-364-98.

Apply force to failure at a maximum

rat e of 12.7 mm per minute.

ENVIRONMENTAL

Thermal shock. See Note. EIA-364-32.

Subject mated specimens to 5

cycles between - 40 and 80

Humidity-temperature cy cling. See Note. EIA-364-31,

Method III.

Subject mated specimens to 10

cycles (10 days) between 25 and

C at 80 to 100% RH.

Temperature lif e. See Note. EIA-364-17,

Method A,

Test Time Condit ion C.

Subject mated specimens to 80

for 500 hours.

Mixed flowi ng gas. See Note. EI A-364- 65,

Class IIA (4 gas).

Subject mated specimens to

environmental Class I IA f or 20

days.

Shall meet visual requirements, show no physical damage, and meet requir ements of addit ional

NOTE

test s as specifi ed in the Product Qualif icati on and Requalification Test Sequence shown in Figur e

Fi gure 1 ( end)

108-2087

Rev A 4 of 5

3.6. Product Qualif icati on and Requalif icati on Test Sequence

Test or Exami nation

Test Group (a)

1234567

Test Sequence (b)

Initial examinat ion of product 1111111

Low level contact resist ance 2,6 2,4 2,4

Vol tage st anding wave ratio 2

Insulation resistance 2,6

Wi thstanding voltage 3,7

RF insertion loss 3

Solderability 2

Vibration 4

Mechanical shock 5

Durability 3

Int erface retention f orce 2

Thermal shock 4

Humidity-temperature cy cling 5

Temperature lif e 3(c)

Mixed flowi ng gas 3(c)

Fi nal examination of product 7558433

(a) See paragraph 4.1.A.

NOTE

(b) Numbers indicat e sequence in which tests ar e performed.

Fi gure 2

4. QUALITY ASSURANCE PROVISIONS

4.1. Qual ification Testing

A. Specimen Sel ection

Speci mens shall be prepared in accordance with applicable Instruct ion Sheets and shall be

sel ected at random from current production. All test groups shall each consist of a minimum of 5

specimens.

B. Test Sequence

Qual ification inspection shall be verified by testing specimens as specified in Figure 2.

4.2. Requal ification Testing

If changes signif icantl y af fecting form, fit or f unction ar e made to the product or manufacturing process,

product assurance shall coordinate requalif icati on testing, consisting of all or part of the original testing

sequence as deter mined by development/product, quality and reliab ility engineering.

108-2087

Rev A 5 of 5

4.3. Acceptance

Acceptance is based on veri ficat ion that the product meets the requirements of Figur e 1. Failures

att ribut ed to equipment, test setup or operator def iciencies shall not disqualify the product. If product

failure occurs, corrective action shall be taken and specimens resubmitt ed for qualif icati on. T esting to

confirm corrective action is required befor e resubmi ttal.

4.4. Qual ity Conformance Inspection

The applicable quality inspection plan shall specify the sampling acceptable quality level t o be used.

Di mensional and functional r equirements shal l be in accordance w ith the applicable product drawing and

this specification.