AYF53 FPC CONNECTORS Y5B/Y5BW (0.5 mm pitch) 0.5 mm pitch, Back lock structure Low profile and space saving body of 1.0 mm high and 3.20 mm deep (3.70 mm including the lever) Y5B and Y5BW can have a minimum of four and two contacts respectively, contributing to the miniaturization and thickness reduction of target equipment. New Y5B Structure to lock through-holes and notches on both ends of the FPC with holding contacts Applicable FPC shapes 1.00 Unit: mm 0 3.2 4 contacts (Y5B: minimum) Y5BW * Wiring patterns can be located underneath the connector. * Man-hours for assembly can be reduced by delivering the connectors with their levers opened. * Y5BW features advanced functionality, including a structure to temporarily hold the FPC and a higher holding force. The FPC holding contacts located on both ends of the connector facilitate positioning of FPC and further enhance the FPC holding force. Compliance with RoHS Directive FEATURES * Low profile, space saving back lock type with improved lever operability * Mechanical design freedom achieved by top and bottom double contacts * Low profile, space saving design with a wide selection, including a type with a small number of contacts With notches With through-holes (1) The holding contacts lock the FPC by its through-holes or notches, allowing users to confirm the completion of the FPC insertion operation. (2) The inserted FPC can be temporarily held until the lever is closed. (3) When the lever is closed, the holding contacts lock the FPC by its through-holes and notches, enhancing the FPC holding force. APPLICATIONS A wide range of digital equipment, including mobile phones, PCs, DSCs, and DVCs. Ideal for their touch panels and LCD backlights, which require connectors with a small number of contacts. ORDERING INFORMATION AYF 5 3 5 53: FPC Connector 0.5 mm pitch (Back lock) Number of contacts (2 digits) Function 3: Top and bottom double contacts (Y5B) 6: Top and bottom double contacts, lock holding type (Y5BW) Surface treatment (Contact portion / Terminal portion) 5: Au plating/Au flash plating (Ni barrier) PRODUCT TYPES Height 1.0 mm Y5B Number of contacts 4 6 8 10 12 24 50 Part number AYF530435 AYF530635 AYF530835 AYF531035 AYF531235 AYF532435 AYF535035 Y5BW Number of contacts 2 4 6 8 10 22 48 Part number AYF530265 AYF530465 AYF530665 AYF530865 AYF531065 AYF532265 AYF534865 Packing Inner carton (1-reel) Outer carton 5,000 pieces 10,000 pieces Notes: 1. Order unit; For mass production: in 1-inner carton (1-reel) units Samples for mounting check: in 50-connector units. Please contact our sales office. 2. Please contact are sales office for connectors having a number of contacts other than those listed above. panasonic-electric-works.net/ac AYF53 SPECIFICATIONS 1. Characteristics Electrical characteristics Mechanical characteristics Item Rated current Rated voltage Insulation resistance Specifications 0.5A/contact 50V AC/DC Min. 1,000M (initial) Breakdown voltage 250V AC for 1 min. Contact resistance Max. 80m FPC holding force Y5B: Min. 0.2N/contacts x contacts (initial) Y5BW: Min. 0.2N/contacts x contacts + 2.0N (initial) Contact holding force Min. 0.2N/contacts Soldering terminal holding force Ambient temperature Storage temperature Thermal shock resistance (with FPC inserted) Environmental characteristics Humidity resistance (with FPC inserted) Saltwater spray resistance (with FPC inserted) H2S resistance (with FPC inserted) Soldering heat resistance Lifetime characteristics Unit weight Insertion and removal life Conditions Min. 0.2N/contacts Using 250V DC megger (applied for 1 min.) No short-circuiting or damage at a detection current of 1 mA when the specified voltage is applied for one minute. Based on the contact resistance measurement method specified by JIS C 5402. Measurement of the maximum force applied until the inserted compatible FPC is pulled out in the insertion axis direction while the connector lever is closed Y5B: Measuring the maximum force. As the contact is axially pull out. Y5BW: Measuring the maximum force. As the contact and holding terminal are axially pull out. Measuring the maximum force. As the soldering terminal is axially pull out. -55C to +85C -55C to +85C (product only) -40C to +50C (emboss packing) No freezing at low temperatures. No dew condensation. 5 cycles, insulation resistance min. 100M, contact resistance max. 100m Sequence 1. -55 -30 C, 30 minutes 2. ~ , Max. 5 minutes 3. 85 +30 C, 30 minutes 4. ~ , Max. 5 minutes 120 hours, insulation resistance min. 100M, contact resistance max. 100m 24 hours, insulation resistance min. 100M, contact resistance max. 100m 48 hours, contact resistance max. 100m Peak temperature: 260C or less 300C within 5 sec. 350C within 3 sec. Bath temperature 402C, humidity 90 to 95% R.H. Bath temperature 352C, saltwater concentration 51% Bath temperature 402C, gas concentration 31 ppm, humidity 75 to 80% R.H. Reflow soldering Soldering iron 20 times Repeated insertion and removal: min. 10 sec./time Y5B (50 contacts): 0.16 g 2. Material and surface treatment Part name Material Housing: LCP resin (UL94V-0) Lever: LCP resin (UL94V-0) Molded portion Contact Copper alloy Holding contact portion Soldering terminal portion Copper alloy Copper alloy Surface treatment -- Contact portion; Base: Ni plating, Surface: Au plating Terminal portion; Base: Ni plating, Surface: Au plating Terminal portion; Base: Ni plating, Surface: Au plating Base: Ni plating, Surface: Au plating DIMENSIONS (Unit: mm) Y5B A B0.20 Terminal coplanarity (0.30) 0.1 (0.50) (Contact and soldering terminal) 2.90 3.20 (0.15) (0.32) (0.15) C0.20 (3.70) (1.76) 1.000.10 0.500.10 (1.50) (FPC insertion depth) Number of contacts/ dimension 4 A B C 4.00 3.36 1.50 6 8 10 12 24 50 5.00 6.00 7.00 8.00 14.00 27.00 4.36 5.36 6.36 7.36 13.36 26.36 2.50 3.50 4.50 5.50 11.50 24.50 panasonic-electric-works.net/ac AYF53 Y5B RECOMMENDED FPC/FFC DIMENSIONS The conductive parts should be based by Ni plating and then Au plating. (A+1)0.05 A0.03 (FPC) 0.350.03 (FFC) 0.300.03 20 0. 0.300.03 1.50 min. (Exposed part of the conductor) R Y5BW 2.50 min. (Reinforcing plate) 0.500.07 0.500.03 Number of contacts/ dimension 4 1.50 6 8 10 12 24 50 2.50 3.50 4.50 5.50 11.50 24.50 A A C Terminal coplanarity (0.30) 0.1 (Contact, holding (0.50) contact and soldering terminal) B0.20 (0.15) (3.70) 2.90 3.20 (1.76) 1.000.10 0.500.10 (1.50) (FPC insertion depth) Number of contacts/ dimension 2 4.00 3.36 1.50 4 6 8 10 22 48 5.00 6.00 7.00 8.00 14.00 27.00 4.36 5.36 6.36 7.36 13.36 26.36 2.50 3.50 4.50 5.50 11.50 24.50 (0.15) (0.32) C0.20 A B C Y5BW RECOMMENDED FPC DIMENSIONS The conductive parts should be based by Ni plating and then Au plating. 0.20 Must not reach the conductor 1.00 (A+2)0.05 A0.03 0.500.03 (Pitch) 0.350.03 0.45+0.03 -0.05 .20 R0 0.300.03 1.050.05 1.50 min. (Exposed part of the conductor) R0.20R 0.300.03 +0.07 -0.06 2.50 min. (Reinforcing plate) 0.70+0.03 -0.05 .20 R0 0.800.05 1.300.10 1.50 min. (Exposed part of the conductor) 1.000.07 Through-holes type (A+2)0.05 A0.03 0.500.03 (Pitch) 0.350.03 0.50+0.03 -0.05 dia. (Through-hole) Must not reach the conductor 2.50 min. (Reinforcing plate) Notches type Number of contacts/ dimension 2 0.50 4 6 8 10 22 48 1.50 2.50 3.50 4.50 10.50 23.50 A EMBOSSED TAPE DIMENSIONS (Unit: mm) (Common for respective contact type) * Specifications for taping (In accordance with JIS C 0806-1990. However, not applied to the mounting-hole pitch of some connectors.) Tape II A: 44 mm (A0.3) (C) Taping reel Top cover tape (B) (1.75) (2.0) (4.0) (2.0) (4.0) (1.75) Embossed carrier tape Embossed mounting-hole 8.0 (8.0) Label 1.5 0 +00.1 .0 dia .1 +0 0.0 50 1. Leading direction after packaging (B) (D1) 380 dia. Tape I A: Max. 24 mm (A0.3) * Specifications for the plastic reel (In accordance with EIAJ ET-7200B.) a. di . panasonic-electric-works.net/ac AYF53 * Y5B Dimension table (Unit: mm) Number of contacts 4, 6, 8, and 10 contacts 12 and 24 contacts 50 contacts Type of taping Tape I Tape I Tape II A 16.0 24.0 44.0 B 7.5 11.5 20.2 C - - 40.4 D 17.4 25.4 45.4 Quantity per reel 5,000 5,000 5,000 A 16.0 24.0 44.0 B 7.5 11.5 20.2 C - - 40.4 D 17.4 25.4 45.4 Quantity per reel 5,000 5,000 5,000 * Y5BW Dimension table (Unit: mm) Number of contacts 2, 4, 6, and 8 contacts 10 and 22 contacts 48 contacts Type of taping Tape I Tape I Tape II * Connector orientation with respect to embossed tape feeding direction Type Y5B Direction of tape progress Y5BW NOTES 1. Recommended PC board and metal mask patterns Appropriate control of solder amount is required to minimize solder bridges and other defects for connectors with 0.3 mm or 0.5 mm pitch terminals, which require high-density mounting. Refer to the recommended PC board pattern. * Y5B C0.05 0.500.05 0.300.05 Terminal 0.400.05 D0.10 Soldering terminal 0.800.05 3.300.05 Connector outline (lever opened) 0.800.05 Recommended PC board pattern (Mount pad arrangement pattern) (TOP VIEW) Number of contacts/ dimension 4 1.50 3.10 6 8 10 12 24 50 2.50 3.50 4.50 5.50 11.50 24.50 4.10 5.10 6.10 7.10 13.10 26.10 Number of contacts/ dimension 2 C D 1.50 3.10 4 6 8 10 22 48 2.50 3.50 4.50 5.50 11.50 24.50 4.10 5.10 6.10 7.10 13.10 26.10 C D * Y5BW 0.400.05 3.300.05 Contact Holding contact D0.10 Soldering terminal 0.800.05 Connector outline (lever opened) C0.05 0.500.05 0.300.05 0.800.05 Recommended PC board pattern (Mount pad arrangement pattern) (TOP VIEW) 2. Precautions for insertion/removal of FPC Do not apply an excessive load to the lever in the opening direction beyond its open position; otherwise, the lever may be deformed or removed. Do not open/close the lever without an FPC inserted; otherwise, the terminals may be deformed, and the FPC insertion force may increase. Do not apply an excessive load to the lever in a direction perpendicular to the lever rotation axis or in the lever opening direction; otherwise, the terminals may be deformed, and the lever may be removed. These connectors are of the back lock type, which has the FPC insertion section on the opposite side of the lever. Be careful not to make a mistake in the FPC insertion position or the lever opening/closing position. Otherwise, a contact failure or connector breakage may occur. These connectors have top and bottom double contacts. Do not insert an FPC upside down. Inserting an FPC in a direction opposite to that you intended may cause an operation failure or malfunction. Fully open the lever to insert an FPC. Completely insert the FPC horizontally. An FPC inserted at an excessive angle to the board may cause the deformation of metal parts, FPC insertion failures, and FPC circuit breakages. Insert the FPC to the full depth of the connector without altering the angle. To close the lever, turn down the lever by pressing the entire lever or both sides of the lever with the balls of fingers. Be careful. If pressure to the lever is applied unevenly, such as to an edge only, it may deform or break. Also, make sure that the lever is closed completely. Not doing so will cause a faulty connection. Avoid applying an excessive load to the top of the lever during or after closing the lever. Otherwise, the terminals may be deformed. When opening the lever to remove the FPC, ensure that the lever will not go over the initial position; otherwise, the lever may be removed. Remove the FPC at parallel with the lever fully opened. If the lever is closed, or if the FPC is forcedly pulled, the product or FPC may break. If a lever is accidentally detached during the handling of a connector, do not use the connector any longer. After an FPC is inserted, carefully handle it so as not to apply excessive stress to the base of the FPC. 3. Cautions for using Y5BW The holding contacts cannot be used as conductors. The holding contacts are located on both ends of the contacts, and the shape of the soldered portions is the same as that of the other contacts. Therefore, be careful to avoid any confusion. For other cautions, please refer to the last page. panasonic-electric-works.net/ac FPC Connector Selector Chart Types FPC Connector Selector Chart 0.3mm pitch type 0.5mm pitch type Y5B Product name Y5BW AYF5335 Part No. AYF5365 Y5S Y5F Y3FT Y3F Y3B AYF5115 AYF5215 AYF3115 AYF3215 AYF3335 Shape Low profile, space saving back lock type with improved lever operability The lineup includes a type with a small number of contacts. Top and bottom double contacts structure Y5BW features advanced functionality Features Slide lock Back lock Lock structure FPC/FFC Compatibility with FPC/FFC A wide variety of digital equipments Slide lock structure Soldering terminals (Metal clips) resistant to twisting FPC/FFC (Au contact) are also available FPC A wide variety of digital equipments Front lock structure Soldering terminals (Metal clips) resistant to twisting FPC/FFC (Au contact) are also available Front lock Low-profile, space-saving design (Pitch: 0.3 mm) Compatible with FPC with tabs, reliability is increased through secure connectibility Wiring patterns can be located underneath the connector Front lock Low-profile, space-saving design (3.0mm pitch) Compatible with FPC without tabs, allowing smooth FPC insertion Wiring patterns can be located underneath the connector Front lock The world's slimmest* and low profile design (Pitch: 0.3 mm) Mechanical design freedom achieved by top and bottom double contacts Wiring patterns can be located underneath the connector Back lock FPC/FFC FPC/FFC FPC FPC FPC Contact pitch 0.5mm 0.5mm 0.5mm 0.3mm 0.3mm 0.3mm Terminal pitch 0.5mm 0.5mm 0.5mm 0.6mm 0.6mm 0.6mm Top and bottom double contacts Bottom contact Bottom contact Bottom contact Bottom contact Top and bottom double contacts 1.0mm 1.9mm 2.0mm 0.9mm 0.9mm 0.9mm 3.7mm (Including lever) 3.2mm 5.2mm (Including lever) 4.0mm Contact structure 10 Mounting height 5 1 Dimensions (short width) 6.3mm (Including lever) 5.4mm 3.2mm (Including lever) 3.0mm 3.2mm (Including lever) 3.0mm 3.15mm (Including lever) 2.95mm 60 50 50 No. of contacts 48 40 30 24 20 10 4 6 8 22 10 12 2 4 6 24 8 10 50 54 51 51 51 40 45 41 45 41 45 45 34 31 33 35 39 31 33 35 39 31 33 35 39 26 28 23 25 27 29 23 25 27 29 21 23 25 27 15 17 15 17 15 7 9 11 13 15 17 Rated current 0.5A/contact 0.5A/contact 0.5A/contact 0.2A/contact 0.2A/contact 0.2A/contact Rated voltage 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC Ambient temperature -55C to +85C -55C to +85C -55C to +85C -55C to +85C -55C to +85C -55C to +85C Insertion and removal life 20 times 30 times 30 times 30 times 30 times 20 times Terminal shape SMD SMD SMD SMD SMD SMD RoHS directive Compliance Compliance Compliance Compliance Compliance Compliance panasonic-electric-works.net/ac FPC Connector Selector Chart Types FPC Connector Selector Chart 0.3mm pitch type 0.5mm pitch type Y5B Product name Y5BW AYF5335 Part No. AYF5365 Y5S Y5F Y3FT Y3F Y3B AYF5115 AYF5215 AYF3115 AYF3215 AYF3335 Shape Low profile, space saving back lock type with improved lever operability The lineup includes a type with a small number of contacts. Top and bottom double contacts structure Y5BW features advanced functionality Features Slide lock Back lock Lock structure FPC/FFC Compatibility with FPC/FFC A wide variety of digital equipments Slide lock structure Soldering terminals (Metal clips) resistant to twisting FPC/FFC (Au contact) are also available FPC A wide variety of digital equipments Front lock structure Soldering terminals (Metal clips) resistant to twisting FPC/FFC (Au contact) are also available Front lock Low-profile, space-saving design (Pitch: 0.3 mm) Compatible with FPC with tabs, reliability is increased through secure connectibility Wiring patterns can be located underneath the connector Front lock Low-profile, space-saving design (3.0mm pitch) Compatible with FPC without tabs, allowing smooth FPC insertion Wiring patterns can be located underneath the connector Front lock The world's slimmest* and low profile design (Pitch: 0.3 mm) Mechanical design freedom achieved by top and bottom double contacts Wiring patterns can be located underneath the connector Back lock FPC/FFC FPC/FFC FPC FPC FPC Contact pitch 0.5mm 0.5mm 0.5mm 0.3mm 0.3mm 0.3mm Terminal pitch 0.5mm 0.5mm 0.5mm 0.6mm 0.6mm 0.6mm Top and bottom double contacts Bottom contact Bottom contact Bottom contact Bottom contact Top and bottom double contacts 1.0mm 1.9mm 2.0mm 0.9mm 0.9mm 0.9mm 3.7mm (Including lever) 3.2mm 5.2mm (Including lever) 4.0mm Contact structure 10 Mounting height 5 1 Dimensions (short width) 6.3mm (Including lever) 5.4mm 3.2mm (Including lever) 3.0mm 3.2mm (Including lever) 3.0mm 3.15mm (Including lever) 2.95mm 60 50 50 No. of contacts 48 40 30 24 20 10 4 6 8 22 10 12 2 4 6 24 8 10 50 54 51 51 51 40 45 41 45 41 45 45 34 31 33 35 39 31 33 35 39 31 33 35 39 26 28 23 25 27 29 23 25 27 29 21 23 25 27 15 17 15 17 15 7 9 11 13 15 17 Rated current 0.5A/contact 0.5A/contact 0.5A/contact 0.2A/contact 0.2A/contact 0.2A/contact Rated voltage 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC 50V AC/DC Ambient temperature -55C to +85C -55C to +85C -55C to +85C -55C to +85C -55C to +85C -55C to +85C Insertion and removal life 20 times 30 times 30 times 30 times 30 times 20 times Terminal shape SMD SMD SMD SMD SMD SMD RoHS directive Compliance Compliance Compliance Compliance Compliance Compliance panasonic-electric-works.net/ac FPC CONNECTORS COMMON CAUTIONS FOR USE COMMON CAUTIONS FOR USE PC board design Design the recommended foot pattern in order to secure the mechanical strength in the soldered areas of the terminal. FPC and equipment design Design the FPC based on the recommended dimensions to ensure the required connector performance. In addition, carefully check the equipment design and take required measures for the equipment to prevent the FPC from being removed subsequent to a fall, vibration, or other impact due to the FPC size, weight, or the reaction force of the routed FPC. Connector mounting In case the connector is picked up by chucking during mounting, an excessive mounter chucking force may deform the molded or metal part of the connector. Consult us in advance if chucking is to be applied. Soldering 1) Manual soldering. * Due to the low profile, if an excessive amount of solder is applied to this product during manual soldering, the solder may creep up to near the contact points, or interference by solder may cause imperfect contact. * Make sure that the soldering iron tip is heated within the temperature and time limits indicated in the specifications. * Flux from the solder wire may adhere to the contact surfaces during soldering operations. After soldering, carefully check the contact surfaces and clean off any flux before use. * Be aware that a load applied to the connector terminals while soldering may displace the contact. * Thoroughly clean the iron tip. 2) Reflow soldering * Screen-printing is recommended for printing paste solder. Y3FT/Y3F/Y3B/Y5F/Y5B/Y5BW To determine the relationship between the screen opening area and the PC board foot pattern area, refer to the diagrams in the recommended patterns for PC boards and metal masks when setting. Note that excess solder on the terminals prevents complete insertion of the FPC, and that excess solder on the metal clips prevents the lever from rotating. Y5S Note that excess solder inhibits the slider lock operation. Terminal Paste solder PC board foot pattern Y3FT/Y3F/Y3B/Y5S/Y5B/Y5BW Screen thickness of 120m is recommended for paste solder printing. * Consult us when using a screen-printing thickness other than that recommended. * Depending on the size of the connector being used, self alignment may not be possible. Accordingly, carefully position the terminal with the PC board pattern. * The recommended reflow temperature profile is given in the figure below Recommended reflow temperature profile Y3FT/Y3F/Y3B/Y5B/Y5BW Upper limit (Soldering heat resistance) Lower limit (Solder wettability) Temperature Peak temperature 260C 230C 180C Preheating 220C 200C 25 sec. 150C 60 to 120 sec. 70 sec. Time Y5S Temperature Peak temperature 250C 200C 180C * Some solder and flux types may cause serious solder creeping. Take the solder and flux characteristics into consideration when setting the reflow soldering conditions. * When performing reflow soldering on the back of the PC board after reflow soldering the connector, secure the connector using, for example, an adhesive. (Double reflow soldering on the same side is possible) 3) Reworking on a soldered portion * Finish reworking in one operation. * For reworking of the solder bridge, use a soldering iron with a flat tip. Do not add flux, otherwise, the flux may creep to the contact parts. * Use a soldering iron whose tip temperature is within the temperature range specified in the specifications. Do not drop the product or handle carelessly. Otherwise, the terminals may become deformed due to excessive force or the solderability during reflow soldering may degrade. Don't open/close the lever or insert/ remove an FPC until the connector is soldered. Forcibly applied external pressure on the terminals can weaken the adherence of the terminals to the molded part or cause the terminals to lose their evenness. In addition, do not insert an FPC into the connector before soldering the connector. When cutting or bending the PC board after mounting the connector, be careful that the soldered sections are subjected to excessive forces. Do not the soldered areas to be subjected to forces 150C Preheating 60 to 120 sec. Min. 200C, 70 sec. Time Y5F Temperature Peak temperature 260C 200C 180C 150C Preheating 60 to 120 sec. Other Notes When coating the PC board after soldering the connector to prevent the deterioration of insulation, perform the coating in such a way so that the coating does not get on the connector. The connectors are not meant to be used for switching. Min. 200C, 70 sec. Time For other details, please verify with the product specification sheets. * The temperature is measured on the surface of the PC board near the connector terminal. panasonic-electric-works.net/ac