LM4951A LM4951A Wide Voltage Range 1.8 Watt Audio Amplifier With Short Circuit Protection Literature Number: SNAS453B LM4951A Wide Voltage Range 1.8 Watt Audio Amplifier With Short Circuit Protection General Description Features The LM4951A is an audio power amplifier designed for applications with supply voltages ranging from 2.7V up to 9V. The LM4951A is capable of delivering 1.8W continuous average power with less than 1% THD+N into a bridge connected 8 load when operating from a 7.5VDC power supply. Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4951A does not require bootstrap capacitors, or snubber circuits. The LM4951A features a low-power consumption active-low shutdown mode. Additionally, the LM4951A features an internal thermal shutdown protection mechanism and short circuit protection. The LM4951A contains advanced pop & click circuitry that eliminates noises which would otherwise occur during turn-on and turn-off transitions. The LM4951A is unity-gain stable and can be configured by external gain-setting resistors. Pop & click circuitry eliminates noise during turn-on and turn-off transitions Wide supply voltage range: 2.7V to 9V Low current, active-low shutdown mode Low quiescent current Thermal shutdown protection Short circuit protection Unity-gain stable External gain configuration capability Applications Portable devices Cell phones Laptop computers Computer speaker systems MP3 player speakers Key Specifications Wide Voltage Range 2.7V to 9V Quiescent Power Supply Current (VDD = 7.5V) 2.5mA (typ) Power Output BTL at 7.5V, 1.8W (typ) 1% THD Shutdown Current 0.01A (typ) Fast Turn on Time 25ms (typ) Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300578 www.national.com LM4951A Wide Voltage Range 1.8 Watt Audio Amplifier With Short Circuit Protection September 5, 2008 LM4951A Typical Application 300578f4 FIGURE 1. Typical Bridge-Tied-Load (BTL) Audio Amplifier Application Circuit www.national.com 2 LM4951A Connection Diagrams SD Package 30057829 Top View Order Number LM4951ASD See NS Package Number SDC10A SD Package Marking 30057831 Top View U = Fab site code Z = Assembly plant code XY = Date code TT = Die traceability 4951A = LM4951A SD = Package code Ordering Information Order Number Package Package DWG # MSL Level Green Status LM4951ASD 10 Lead LLP SDC10A 1000 units in Tape and Reel Transport Media 1 RoH and no Sb/Br LM4951ASDX 10 Lead LLP SDC10A 4500 units in Tape and Reel 1 RoH and no Sb/Br 3 Features www.national.com LM4951A TABLE 1. Pin Name and Function Pin Number Name Function Type 1 Bypass 1/2 supply reference voltage bypass output. See sections POWER SUPPLY BYPASSING and SELECTING EXTERNAL COMPONENTS for more information. Analog Output 2 Shutdown 3 CCHG 4 NC No connection to die. Pin can be connected to any potential. No Connect 5 VIN Single-ended signal input pin. Analog Input 6 VO- Inverting output of amplifier. 7 GND Shutdown control active low signal. A logic low voltage will put the LM4951A into Shutdown mode. Input capacitor charge to decrease turn on time. See section Selecting A Value for RC for more information. Analog Output Analog Output Ground connection. Ground 8 NC No connection to die. Pin can be connected to any potential. 9 VDD Power supply. 10 VO+ Non-Inverting output of amplifier. Exposed DAP NC No connect. Pin must be electrically isolated (floating) or connected to GND. www.national.com Digital Input No Connect Power 4 Analog Output No Connect JA (LLP) (Note 3) Soldering Information See AN-1187 'Leadless Leadframe Packaging (LLP).' If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Storage Temperature Input Voltage Power Dissipation (Note 3) ESD Rating (Note 4) ESD Rating (Note 5) Junction Temperature (TJMAX) 9.5V -65C to +150C -0.3V to VDD + 0.3V Internally limited 2000V 200V 150C Electrical Characteristics VDD = 7.5V Operating Ratings 73C/W (Notes 1, 2) Temperature Range TMIN TA TMAX -40C T A +85C 2.7V VDD 9V Supply Voltage (Notes 1, 2) The following specifications apply for VDD = 7.5V, AV-BTL = 6dB, RL = 8 unless otherwise specified. Limits apply for TA = 25C. LM4951A Symbol Parameter Conditions Typical (Note 6) Limit (Note 7) 4.5 Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A, RL = 8 BTL 2.5 ISD Shutdown Current VSD = GND (Note 8) 0.01 5 A (max) VOS Output Offset Voltage 5 30 mV (max) VSDIH Shutdown Voltage Input High 1.2 V (min) VSDIL Shutdown Voltage Input Low 0.4 V (max) RPULLDOWN Pull-down Resistor on SD pin TWU Wake-up Time CB = 1.0F TSD Shutdown time CB = 1.0F TSD Thermal Shutdown Temperature PO Output Power THD+N Total Harmonic Distortion + Noise OS Output Noise PSRR Power Supply Rejection Ratio mA (max) 75 45 k (min) 25 35 ms (max) 10 ms (max) 170 150 190 C (min) C (max) THD = 1% (max); f = 1kHz RL = 8 Mono BTL 1.8 1.5 W (min) PO = 600mWRMS; f = 1kHz AV-BTL = 6dB 0.07 0.5 % (max) PO = 600mWRMS; f = 1kHz AV-BTL = 26dB 0.35 % 10 V A-Weighted Filter, Ri = Rf = 20k Input Referred (Note 9) VRIPPLE = 200mVp-p, f = 217Hz, CB = 1.0F, Input Referred Electrical Characteristics VDD = 3.3V 66 56 dB (min) (Notes 1, 2) The following specifications apply for VDD = 3.3V, AV-BTL = 6dB, RL = 8 unless otherwise specified. Limits apply for TA = 25C. LM4951A Symbol Parameter Conditions Typical (Note 6) Limit (Note 7) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A, RL = 8 BTL 2.5 4.5 mA (max) ISD Shutdown Current VSHUTDOWN = GND (Note 8) 0.01 2 A (max) VOS Output Offset Voltage VSDIH Shutdown Voltage Input High VSDIL Shutdown Voltage Input Low TWU Wake-up Time CB = 1.0F TSD Shutdown time CB = 1.0F 3 5 30 mV (max) 1.2 V (min) 0.4 V (max) 25 ms 10 ms (max) www.national.com LM4951A Thermal Resistance Absolute Maximum Ratings (Notes 1, 2) LM4951A LM4951A Symbol PO THD+N Parameter Output Power Total Harmonic Distortion + Noise OS Output Noise PSRR Power Supply Rejection Ratio Conditions Units (Limits) Typical (Note 6) Limit (Note 7) THD = 1% (max); f = 1kHz RL = 8 Mono BTL 280 230 mW (min) PO = 100mWRMS = 1kHz AV-BTL = 6dB 0.07 0.5 % (max) PO = 100mWRMS; f = 1kHz AV-BTL = 26dB 0.35 % 10 V A-Weighted Filter, Ri = Rf = 20k Input Referred, (Note 9) VRIPPLE = 200mVp-p, f = 217Hz, CB = 1F, Input Referred 71 61 dB (min) Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the s or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditionsindicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4951A typical application (shown in Figure 1) with VDD = 7.5V, RL = 8 mono-BTL operation the max power dissipation is 1.42W. JA = 73C/W. Note 4: Human body model, applicable std. JESD22-A114C. Note 5: Machine model, applicable std. JESD22-A115-A. Note 6: Typical values represent most likely parametric norms at TA = +25C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 7: Datasheet min/max specification limits are guaranteed by test or statistical analysis. Note 8: Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to GND for minimum shutdown current. Note 9: Noise measurements are dependent on the absolute values of the closed loop gain setting resistors (input and feedback resistors). www.national.com 6 LM4951A Typical Performance Characteristics THD+N vs Frequency VDD = 3.3V, PO = 100mW, AV = 6dB THD+N vs Frequency VDD = 3.3V, PO = 100mW, AV = 26dB 300578f9 30057802 THD+N vs Frequency VDD = 5V, PO = 400mW, AV = 6dB THD+N vs Frequency VDD = 5V, PO = 400mW, AV = 26dB 30057803 30057804 THD+N vs Frequency VDD = 7.5V, PO = 600mW, AV = 6dB THD+N vs Frequency VDD = 7.5V, PO = 600mW, AV = 26dB 30057805 300578g0 7 www.national.com LM4951A THD+N vs Output Power VDD = 3.3V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 3.3V, f = 1kHz, AV = 26dB 300578g1 30057808 THD+N vs Output Power VDD = 5V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 5V, f = 1kHz, AV = 26dB 30057809 30057810 THD+N vs Output Power VDD = 7.5V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 7.5V, f = 1kHz, AV = 26dB 30057812 30057811 www.national.com 8 Power Supply Rejection vs Frequency VDD = 3.3V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 30057814 30057813 Power Supply Rejection vs Frequency VDD = 5V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 Power Supply Rejection vs Frequency VDD = 5V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 30057816 30057815 Power Supply Rejection vs Frequency VDD = 7.5V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 Power Supply Rejection vs Frequency VDD = 7.5V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 30057818 30057817 9 www.national.com LM4951A Power Supply Rejection vs Frequency VDD = 3.3V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 LM4951A Noise Floor VDD = 3.3V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 3V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30057820 30057819 Noise Floor VDD = 5V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 5V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30057822 30057821 Noise Floor VDD = 7.5V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 7.5V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30057824 30057823 www.national.com 10 LM4951A Power Dissipation vs Output Power VDD = 3.3V, RL = 8, f = 1kHz Power Dissipation vs Output Power VDD = 7.5V, RL = 8, f = 1kHz 30057825 30057826 Supply Current vs Supply Voltage RL = 8, VIN = 0V, Rsource = 50 Clipping Voltage vs Supply Voltage RL = 8, from top to bottom: Negative Voltage Swing; Positive Voltage Swing 30057827 300578e9 Output Power vs Load Resistance VDD = 3.3V, f = 1kHz from top to bottom: THD+N = 10%, THD+N = 1% Output Power vs Supply Voltage RL = 8, from top to bottom: THD+N = 10%, THD+N = 1% 300578f1 300578f0 11 www.national.com LM4951A Output Power vs Load Resistance VDD = 7.5V, f = 1kHz from top to bottom: THD+N = 10%, THD+N = 1% Frequency Response vs Input Capacitor Size RL = 8 from top to bottom: Ci = 1.0F, Ci = 0.39F, Ci = 0.039F 300578f2 www.national.com 300578f3 12 BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4951A consists of two operational amplifiers that drive a speaker connected between their outputs. The value of input and feedback resistors determine the gain of each amplifier. External resistors Ri and Rf set the closed-loop gain of AMPA, whereas two 20k internal resistors set AMPB's gain to -1. Figure 1 shows that AMPA's output serves as AMPB's input. This results in both amplifiers producing signals identical in magnitude, but 180 out of phase. Taking advantage of this phase difference, a load is placed between AMPA and AMPB and driven differentially (commonly referred to as "bridge-tied load"). This results in a differential, or BTL, gain of: AVD = 2(Rf / Ri) (V/V) TA = TJMAX - PDMAX-MONOBTLJA (C) For a typical application with a 7.5V power supply and a BTL 8 load, the maximum ambient temperature that allows maximum stereo power dissipation without exceeding the maximum junction temperature is 46C for the SD package. TJMAX = PDMAX-MONOBTLJA + TA (C) (1) The above examples assume that a device is operating around the maximum power dissipation point. Since internal power dissipation is a function of output power, higher ambient temperatures are allowed as output power or duty cycle decreases. If the result of Equation (2) is greater than that of Equation (3), then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. Further, ensure that speakers rated at a nominal 8 do not fall below 6. If these measures are insufficient, a heat sink can be added to reduce JA. The heat sink can be created using additional copper area around the package, with connections to the ground pins, supply pin and amplifier output pins. Refer to the Typical Performance Characteristics curves for power dissipation information at lower output power levels. Another advantage of the differential bridge output is no net DC voltage across the load. This is accomplished by biasing AMP1's and AMP2's outputs at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a typical single-ended configuration forces a single-supply amplifier's half-supply bias voltage across the load. This increases internal IC power dissipation and may permanently damage loads such as speakers. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a voltage regulator typically use a 10F in parallel with a 0.1F filter capacitors to stabilize the regulator's output, reduce noise on the supply line, and improve the supply's transient response. However, their presence does not eliminate the need for a local 1.0F tantalum bypass capacitance connected between the LM4951A's supply pins and ground. Do not substitute a ceramic capacitor for the tantalum. Doing so may cause oscillation. Keep the length of leads and traces that connect capacitors between the LM4951A's power supply pin and ground as short as possible. Connecting a larger capacitor, CBYPASS, between the BYPASS pin and ground improves the internal bias voltage's stability and improves the amplifier's PSRR. The PSRR improvements increase as the bypass pin capacitor value increases. Too large, however, increases turn-on time and can compromise the amplifier's click and pop performance. The selection of bypass capacitor values, especially CBYPASS, depends on desired PSRR requirements, click and pop performance, system cost, and size constraints. POWER DISSIPATION The LM4951A's dissipation when driving a BTL load is given by Equation (2). For a 7.5V supply and a single 8 BTL load, the dissipation is 1.42W. (2) The maximum power dissipation point given by Equation (2) must not exceed the power dissipation given by Equation (3): PDMAX = (TJMAX - TA) / JA (5) Equation (5) gives the maximum junction temperature TJMAX. If the result violates the LM4951A's maximum junction temperature of 150C, reduce the maximum junction temperature by reducing the power supply voltage or increasing the load resistance. Further allowance should be made for increased ambient temperatures. Bridge mode amplifiers are different from single-ended amplifiers that drive loads connected between a single amplifier's output and ground. For a given supply voltage, bridge mode has an advantage over the single-ended configuration: its differential output doubles the voltage swing across the load. Theoretically, this produces four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited and that the output signal is not clipped. Under rare conditions, with unique combinations of high power supply voltage and high closed loop gain settings, the LM4951A may exhibit low frequency oscillations. PDMAX-MONOBTL = 4(VDD) 2 / 22RL (W) (4) (3) The LM4951A's TJMAX = 150C. In the SD package, the LM4951A's JA is 73C/W when the metal tab is soldered to a copper plane of at least 1in2. This plane can be split between the top and bottom layers of a two-sided PCB. Connect the two layers together under the tab with an array of vias. At any given ambient temperature TA, use Equation (3) to find the maximum internal power dissipation supported by the IC packaging. Rearranging Equation (3) and substituting PDMAX for PDMAX' results in Equation (4). This equation gives the maximum ambient temperature that still allows maximum MICRO-POWER SHUTDOWN The LM4951A features an active-low micro-power shutdown mode. When active, the LM4951A's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The low 0.01A typical shutdown current is achieved by applying a voltage to the SHUTDOWN pin that 13 www.national.com LM4951A stereo power dissipation without violating the LM4951A's maximum junction temperature. Application Information LM4951A is as near to GND as possible. A voltage that is greater than GND may increase the shutdown current. turn-on refers to either applying the power supply voltage or when the micro-power shutdown mode is deactivated. As the VDD/2 voltage present at the BYPASS pin ramps to its final value, the LM4951A's internal amplifiers are configured as unity gain buffers. An internal current source charges the capacitor connected between the BYPASS pin and GND in a controlled manner. Ideally, the input and outputs track the voltage applied to the BYPASS pin. The gain of the internal amplifiers remains unity until the voltage on the bypass pin reaches VDD/2. As soon as the voltage on the bypass pin is stable, there is a delay to prevent undesirable output transients ("click and pops"). After this delay, the device becomes fully functional. SELECTING EXTERNAL COMPONENTS Input Capacitor Value Selection Two quantities determine the value of the input coupling capacitor: the lowest audio frequency that requires amplification and desired output transient suppression. As shown in Figure 1, the input resistor (Ri) and the input capacitor (Ci) create a high-pass filter. The cutoff frequency can be found using Equation (6). fc = 1/2RiCi (Hz) (6) THERMAL SHUTDOWN AND SHORT CIRCUIT PROTECTION The LM4951A has thermal shutdown and short circuit protection to fully protect the device. The thermal shutdown circuit is activated when the die temperature exceeds a safe temperature. The short circuit protection circuitry senses the output current. When the output current exceeds the threshold under a short condition, a short will be detected and the output deactivated until the short condition is removed. If the output current is lower than the threshold then a short will not be detected and the outputs will not be deactivated. Under such conditions the die temperature will increase and, if the condition persist to raise the die temperature to the thermal shutdown threshold, initiate a thermal shutdown response. Once the die cools the outputs will become active. As an example when using a speaker with a low frequency limit of 50Hz, Ci, using Equation (6) is 0.159F with Ri set to 20k. The values for Ci and Ri shown in Figure 1 allow the LM4951A to drive a high efficiency, full range speaker whose response extends down to 20Hz. Selecting Value A For RC The LM4951A is designed for very fast turn on time. The CCHG pin allows the input capacitor to charge quickly to improve click/pop performance. RC protects the CCHG pin from any over/under voltage conditions caused by excessive input signal or an active input signal when the device is in shutdown. The recommended value for RC is 1k. If the input signal is less than VDD+0.3V and greater than -0.3V, and if the input signal is disabled when in shutdown mode, RC may be shorted out. RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT Figures 2-4 show the recommended two-layer PC board layout that is optimized for the SD10A. This circuit is designed for use with an external 7.5V supply 8 (min) speakers. OPTIMIZING CLICK AND POP REDUCTION PERFORMANCE The LM4951A contains circuitry that eliminates turn-on and shutdown transients ("clicks and pops"). For this discussion, www.national.com 14 LM4951A Demonstration Board Circuit 30057830 FIGURE 2. Demo Board Circuit 15 www.national.com LM4951A Demonstration Board Layout 30057832 FIGURE 3. Top Silkscreen 300578f7 FIGURE 4. Top Layer 300578f6 FIGURE 5. Bottom Layer www.national.com 16 LM4951A Bill Of Materials TABLE 2. Bill Of Materials Designator Value Tolerance RIN1 20k 1% 1/8W, 0805 Resistor Part Description R1 200k 1% 1/8W, 0805 Resistor RPULLUP 100k 1% 1/8W, 0805 Resistor R2 1k 1% 1/8W, 0805 Resistor R4, R5 0 1% 1/8W, 0805 Resistor CIN1 0.39F 10% Ceramic Capacitor, 25V, Size 1206 CSUPPLY 4.7F 10% 16V Tantalum Capacitor, Size A CBYPASS 1F 10% 16V Tantalum Capacitor, Size A C1 Not Used 0.100" 1x2 header, vertical mount U1 Comments LM4951A, Mono, 1.8W, Audio Amplifier 17 Input, Output, Vdd/GND Shutdown SDC10A package www.national.com LM4951A Revision History Rev Date 1.0 08/13/08 Initial release. 1.01 09/05/08 Text edits. www.national.com Description 18 LM4951A Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM4951ASD NS Package Number SDC10A 19 www.national.com LM4951A Wide Voltage Range 1.8 Watt Audio Amplifier With Short Circuit Protection Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated