LMC7221AIM5/NOPB - NATIONAL SEMICONDUCTOR

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

LMC7221 Tiny CMOS Comparator with Rail-To-Rail Input and Open Drain Output

Check for Samples: LMC7221

1FEATURES DESCRIPTION

The LM7221 is a micropower CMOS comparator

2• Tiny 5-Pin SOT-23 package saves space available in the space saving 5-Pin SOT-23 package.

• Package is less than 1.43 mm thick This makes this comparator ideal for space and

• Ensured specs at 2.7V, 5V, 15V supplies weight critical designs. The LMC7221 is also

available in the 8-Pin SOIC package. The LMC7221

• Typical supply current 7 μA at 5V is supplied in two offset voltage grades, 5 mV and 15

• Response time of 4 μs at 5V mV.

• LMC7221—open drain output The open drain output can be pulled up with a

• Input common-mode range beyond V−and V+resistor to a voltage which can be higher or lower

• Low input current than the supply voltage—this makes the part useful

for mixed voltage systems.

APPLICATIONS For a tiny comparator with a push-pull output, please

• Mixed voltage battery powered products see the LMC7211 datasheet.

• Notebooks and PDAs

• PCMCIA cards

• Mobile communications

• Alarm and security circuits

• Driving low current LEDs

• Direct sensor interface

Connection Diagram

8-Pin SOIC - Top View 5-Pin SOT-23 - Top View

Figure 1. See Package Number D0008A Figure 2. See Package Number DBV0005A

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

Absolute Maximum Ratings (1)

ESD Tolerance (2) 2 kV

Differential Input Voltage V++0.3V, V−−0.3V

Voltage at Input V++0.3V, V−−0.3V

Voltage at Output Pin 15V

Supply Voltage (V+–V−) 16V

Current at Input Pin (3) ±5 mA

Current at Output Pin(4) (5) ±30 mA

Current at Power Supply Pin 40 mA

Lead Temperature (soldering, 10 sec.) 260°C

Junction Temperature (6) 150°C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test

conditions, see the Electrical Characteristics.

(2) Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of

JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).

(3) All limits are specified by testing or statistical analysis.

(4) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in

exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA may adversely affect reliability.

(5) Limiting input pin current is only necessary for input voltages which exceed the absolute maximum input voltage rating.

(6) The maximum power dissipation is a function of TJ(MAX),θJA. The maximum allowable power dissipation at any ambient temperature is

PD= (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.

Operating Ratings (1)

Supply Voltage 2.7 ≤VCC ≤15V

Temperature Range (2)

LMC7221AI, LMC7221BI −40°C to +85°C

Thermal Resistance (θJA)

8-Pin SOIC 180°C/W

5-Pin SOT-23 325°C/W

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test

conditions, see the Electrical Characteristics.

(2) The maximum power dissipation is a function of TJ(MAX),θJA. The maximum allowable power dissipation at any ambient temperature is

PD= (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.

2.7V Electrical Characteristics

Unless otherwise specified, all limits ensured for TJ= 25°C, V+= 2.7V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at the

temperature extremes.

Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

VOS Input Offset Voltage 3 5 15 mV

8 18 max

TCVOS Input Offset Voltage 1.0 μV/°C

Temperature Drift

Input Offset Voltage Average (3) 3.3 μV/Month

Drift

IBInput Current 0.04 pA

IOS Input Offset Current 0.02 pA

CMRR Common Mode Rejection Ratio 0V ≤VCM ≤2.7V 75 dB

PSRR Power Supply Rejection Ratio 2.7V ≤V+≤15V 80 dB

(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(2) All limits are specified by testing or statistical analysis.

(3) CLincludes the probe and test jig capacitance.

Product Folder Links: LMC7221

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

2.7V Electrical Characteristics (continued)

Unless otherwise specified, all limits ensured for TJ= 25°C, V+= 2.7V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at the

temperature extremes.

Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

AVVoltage Gain 100 dB

CMVR Input Common-Mode Voltage CMRR > 55 dB 3.0 2.9 2.9 V

Range 2.7 2.7 min

CMRR > 55 dB −0.3 −0.2 −0.2 V

0.0 0.0 max

VOL Output Voltage Low ILOAD = 2.5 mA 0.2 0.3 0.3 V

0.4 0.4 max

ISSupply Current VOUT = Low 7 12 12 μA

14 14 max

5.0V and 15.0V Electrical Characteristics

Unless otherwise specified, all limits ensured for TJ= 25°C, V+= 5.0V and 15V, V−= 0V, VCM = VO= V+/2. Boldface limits

apply at the temperature extremes.

Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

VOS Input Offset Voltage 3 5 15 mV

8 18 max

TCVOS Input Offset Voltage Temperature V+= 5V 1.0 μV/°C

Drift V+= 15V 4.0

Input Offset Voltage Average Drift V+= 5V (3) 3.3 μV/Month

V+= 15V (3) 4.0

IBInput Current 0.04 pA

IOS Input Offset Current 0.02 pA

CMRR Common Mode Rejection Ration V+= 5.0V 75 dB

V+= 15.0V 82 dB

PSRR Power Supply Rejection Ratio 5V ≤V+≤10V 80 dB

AVVoltage Gain 100 dB

CMVR Input Common-Mode Voltage V+= 5.0V 5.3 5.2 5.2 V

Range CMRR > 55 dB 5.0 5.0 min

V+= 5.0V −0.3 −0.2 −0.2 V

CMRR > 55 dB 0.0 0.0 max

V+= 15.0V 15.3 15.2 15.2 V

CMRR > 55 dB 15.0 15.0 min

V+= 15.0V −0.3 −0.2 −0.2 V

CMRR > 55 dB 0.0 0.0 max

VOL Output Voltage Low V+= 5V 0.2 0.40 0.40 mV

ILOAD = 5 mA 0.55 0.55 max

V+= 15V 0.2 0.40 0.40 mV

ILOAD = 5 mA 0.55 0.55 max

ISSupply Current VOUT = Low 7 14 14 μA

18 18 max

(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(2) All limits are specified by testing or statistical analysis.

(3) CLincludes the probe and test jig capacitance.

Product Folder Links: LMC7221

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

5.0V and 15.0V Electrical Characteristics (continued)

Unless otherwise specified, all limits ensured for TJ= 25°C, V+= 5.0V and 15V, V−= 0V, VCM = VO= V+/2. Boldface limits

apply at the temperature extremes.

Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

ISC Short Circuit Current Sinking (4) 45 mA

(4) Limiting input pin current is only necessary for input voltages which exceed the absolute maximum input voltage rating.

Leakage Characteristics

TJ= 25°C Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

ILEAKAGE Output Leakage Current V+= 2.7V

VIN(+) = 0.5V 0.1 500 500 nA

VIN(−) = 0V

VOUT = 15V

(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(2) All limits are specified by testing or statistical analysis.

AC Electrical Characteristics

Unless otherwise specified, all limits ensured for TJ= 25°C, V+= 5V, V−= 0V, VCM = VO= V+/2. Boldface limits apply at the

temperature extreme.

Parameter Test Conditions LMC7221AI LMC7221BI Units

Typ(1) Limit(2) Limit(2)

trise Rise Time f = 10 kHz, CL= 50 pF, (3) 0.3 μs

Overdrive = 10 mV, 5 kΩPullup

tfall Fall Time f = 10 kHz, CL= 50 pF, (3) 0.3 μs

Overdrive = 10 mV, 5 kΩPullup

tPHL Propagation Delay f = 10 kHz, CL= 50 pF, 10 mV 10 μs

(High to Low) (4) 5 kΩPullup (3) 100 mV 4

V+= 2.7V, f = 10 kHz, 10 mV 10 μs

CL= 50 pF, 5 kΩPullup (3) 100 mV 4

tPLH Propagation Delay f = 10 kHz, CL= 50 pF, 10 mV 6 μs

(Low to High) (4) 5 kΩPullup (3) 100 mV 4

V+= 2.7V, f = 10 kHz, 10 mV 7 μs

CL= 50 pF, 5 kΩPullup (3) 100 mV 4

(1) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

(2) All limits are specified by testing or statistical analysis.

(3) Do not short circuit the output to V+when V+is greater than 12V or reliability will be adversely affected.

(4) Input offset voltage average drift is calculated by dividing the accelerated operating life VOS drift by the equivalent operational time. This

represents worst case input conditions and includes the first 30 days of drift.

Product Folder Links: LMC7221

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

Typical Performance Characteristics

Supply Current Supply Current

vs. vs.

Supply Voltage Temperature while Sinking

Figure 3. Figure 4.

Output Sinking Current Output Sinking Current

vs. vs.

Supply Voltage Output Voltage @ 5V

Figure 5. Figure 6.

Output Sinking Current

vs.

Output Voltage @ 15V Response Time for Various Input Overdrives −tPHL

Figure 7. Figure 8.

Product Folder Links: LMC7221

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

Typical Performance Characteristics (continued)

Response Time Response Time

vs. vs

Various Input Overdrives −tPHL Various Input Overdrives −tPHL

Figure 9. Figure 10.

Input Bias Current Input Bias Current

vs. vs.

Common Mode Voltage Common Mode Voltage

Figure 11. Figure 12.

Input Bias Current Input Bias Current

vs. vs.

Common Mode Voltage Temperature

Figure 13. Figure 14.

Product Folder Links: LMC7221

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

Typical Performance Characteristics (continued)

Leakage Current

vs.

Supply Voltage

Figure 15.

APPLICATION INFORMATION

BENEFITS OF THE LMC7221 TINY COMPARATOR

Size

The small footprint of the 5-Pin SOT-23 packaged Tiny Comparator, (0.120 x 0.118 inches, 3.05 x 3.00 mm)

saves space on printed circuit boards, and enable the design of smaller electronic products. Because they are

easier to carry, many customers prefer smaller and lighter products.

Height

The height (0.056 inches, 1.43 mm) of the Tiny Comparator makes it possible to use it in PCMCIA type III cards.

Simplified Board Layout

The Tiny Comparator can simplify board layout in several ways. First, by placing a comparator where

comparators are needed, instead of routing signals to a dual or quad device, long pc traces may be avoided.

By using multiple Tiny Comparators instead of duals or quads, complex signal routing and possibly crosstalk can

be reduced.

Low Supply Current

The typical 7 μA supply current of the LMC7221 extends battery life in portable applications, and may allow the

reduction of the size of batteries in some applications.

Wide Voltage Range

The LMC7221 is characterized at 15V, 5V and 2.7V. Performance data is provided at these popular voltages.

This wide voltage range makes the LMC7221 a good choice for devices where the voltage may vary over the life

of the batteries.

Digital Outputs Representing Signal Level

Comparators provide a high or low digital output depending on the voltage levels of the (+) and (−) inputs. This

makes comparators useful for interfacing analog signals to microprocessors and other digital circuits. The

LMC7221 can be thought of as a one-bit a/d converter.

Open Drain Output

The open drain output is like the open collector output of a logic gate. This makes the LMC7221 very useful for

mixed voltage systems.

Product Folder Links: LMC7221

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

Driving LEDs (Light Emitting Diodes)

With a 5 volt power supply, the LMC7221's output sinking current can drive small, high efficiency LEDs for

indicator and test point circuits. The small size of the Tiny package makes it easy to find space to add this

feature to even compact designs.

Input range to Beyond Rail to Rail

The input common mode range of the LMC7221 is slightly larger than the actual power supply range. This wide

input range means that the comparator can be used to sense signals close to the power supply rails. This wide

input range can make design easier by eliminating voltage dividers, amplifiers, and other front end circuits

previously used to match signals to the limited input range of earlier comparators. This is useful to power supply

monitoring circuits which need to sense their own power supply, and compare it to a reference voltage which is

close to the power supply voltage. The wide input range can also be useful for sensing the voltage drop across a

current sense resistor for battery chargers.

Zero Crossing Detector

Since the LMC7221's common mode input range extends below ground even when powered by a single positive

supply, it can be used with large input resistors as a zero crossing detector.

Low Input Currents and High Input Impedance

These characteristics allow the LMC7221 to be used to sense high impedance signals from sensors. They also

make it possible to use the LMC7221 in timing circuits built with large value resistors. This can reduce the power

dissipation of timing circuits. For very long timing circuits, using high value resistors can reduce the size and cost

of large value capacitors for the same R-C time constant.

Direct Sensor Interfacing

The wide input voltage range and high impedance of the LMC7221 may make it possible to directly interface to a

sensor without the use of amplifiers or bias circuits. In circuits with sensors which can produce outputs in the

tens to hundreds of millivolts, the LMC7221 can compare the sensor signal with an appropriately small reference

voltage. This may be done close to ground or the positive supply rail. Direct sensor interfacing may eliminate the

need for an amplifier for the sensor signal. Eliminating the amplifier can save cost, space, and design time.

LOW VOLTAGE OPERATION

Comparators are the common devices by which analog signals interface with digital circuits. The LMC7221 has

been designed to operate at supply voltages of 2.7V without sacrificing performance to meet the demands of 3V

digital systems.

At supply voltages of 2.7V, the common-mode voltage range extends 200 mV (ensured) below the negative

supply. This feature, in addition to the comparator being able to sense signals near the positive rail, is extremely

useful in low voltage applications.

Figure 16. Even at Low-Supply Voltage of 2.7V, an Input Signal which Exceeds the Supply Voltages

Produces No Phase Inversion at the Output

At V+= 2.7V propagation delays are tPLH =4μs and tPHL =4μs with overdrives of 100 mV.

Please refer to the performance curves for more extensive characterization.

Product Folder Links: LMC7221

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

OPEN DRAIN OUTPUT

Output Stage

Figure 17. Output Stage

Figure 17 shows the difference between push-pull output and open drain output.

Push pull outputs will have a conventional high or low digital output, the same as a logic gate. Low will be the

negative supply rail (usually ground) and high will be the positive supply rail.

This is useful if the chips you are interfacing to run on the same supply voltage as the comparator. An example

would be an all +5V system.

Open drain outputs will only pull low—for the high output they depend on an external pull-up resistor. This can

pull up to a voltage higher or lower than the comparator supply voltage. This voltage can be as high as 15V. This

makes the open drain parts useful in mixed voltage systems. An example would be where the comparator runs at

5V and the logic circuits are at 3.3V. The pull-up resistor would go to the 3.3V supply.

Open drain outputs are the CMOS equivalent of open collector outputs.

OUTPUT SHORT CIRCUIT CURRENT

The LMC7221 has short circuit protection of 40 mA. However, it is not designed to withstand continuous short

circuits, transient voltage or current spikes, or shorts to any voltage beyond the supplies. A resistor in series with

the output should reduce the effect of shorts. For outputs which send signals off PC boards additional protection

devices, such as diodes to the supply rails, and varistors may be used.

INPUT PROTECTION

If input signals are likely to exceed the common mode range of the LMC7221, or it is likely that signals may be

present when power is off, damage to the LMC7221 may occur. Large value (100 kΩto MΩ) input resistors may

reduce the likelihood of damage by limiting the input currents. Since the LMC7221 has very low input leakage

currents, the effect on accuracy will be small. Additional protection may require the use of diodes, as shown in

Figure 18. Note that diode leakage current may affect accuracy during normal operation.

The R-C time constant of RIN and the diode capacitance may also slow response time.

Product Folder Links: LMC7221

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

Figure 18.

LAYOUT CONSIDERATIONS

The LMC7221 is not an especially fast comparator, so high speed design practices are not required. The

LMC7221 is capable of operating with very high impedance inputs, so precautions should be taken to reduce

noise pickup with high impedance (∼100 kΩand greater) designs and in electrically noisy environments.

Keeping high value resistors close to the LMC7221 and minimizing the size of the input nodes is a good practice.

With multilayer designs, try to avoid long loops which could act as inductors (coils). Sensors which are not close

to the comparator may need twisted pair or shielded connections to reduce noise.

PUSH-PULL OUTPUTS, DUAL VERSIONS

The LMC7211 is a comparator similar to the LMC7221, but with push-pull outputs which can source current.

The performance of the LMC7221 is available in a dual device. Please see the LMC6772 datasheet. For a dual

device with push-pull outputs, please see the LMC6762 datasheet.

Rail-to-Rail Input Low Power Comparators—

Push-Pull Output

LMC7221 5-Pin SOT-23, 8-Pin SOIC Single

LMC6762 8-Pin SOIC Dual

Open Drain Output

LMC7221 5-Pin SOT-23, 8-Pin SOIC Single

LMC6772 8-Pin SOIC Dual

ADDITIONAL 5-Pin SOT-23 TINY DEVICES

TI has additional parts available in the space saving SOT-23 Tiny package, including amplifiers, voltage

references, and voltage regulators, including the following:

1 MHz gain-bandwidth rail-to-rail input and output amplifier—high input impedance and high gain 700 μA typical

LMC7101 current 2.7V, 3V, 5V and 15V specifications.

Low power 50 kHz gain-bandwidth rail-to-rail input and output amplifier with 25 μA typical current specified at 2.7V,

LMC7111 3.0V, 3.3V, 5V and 10V.

LM7131 Tiny Video amp with 70 MHz gain bandwidth 3V, 5V and ±5V specifications.

LP2980 Micropower SOT 50 mA Ultra Low-Dropout Regulator.

LM4040 Precision micropower shunt voltage reference. Fixed voltages of 2.500V, 4.096V, 5.000V, 8.192V and 10.000V.

LM4041 Precision micropower shut voltage reference 1.225V and adjustable.

LM385 Low current voltage reference. Fixed Voltages of 1.2V and 2.5V.

Product Folder Links: LMC7221

LMC7221

www.ti.com

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

Contact your TI representative for the latest information.

SPICE MACROMODEL

A Spice Macromodel is available for the LMC7221 comparator on the TI Amplifier Macromodel disk. Contact your

TI representative to obtain the latest version.

Product Folder Links: LMC7221

LMC7221

SNOS748E –SEPTEMBER 1999–REVISED MARCH 2013

www.ti.com

REVISION HISTORY

Changes from Revision D (March 2013) to Revision E Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 11

Product Folder Links: LMC7221

PACKAGE OPTION ADDENDUM

www.ti.com 11-Jan-2021

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead finish/

Ball material

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LMC7221AIM/NOPB ACTIVE SOIC D 8 95 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC72

21AIM

LMC7221AIM5 ACTIVE SOT-23 DBV 5 1000 Non-RoHS

& Green Call TI Call TI -40 to 85 C01A

LMC7221AIM5/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C01A

LMC7221AIM5X/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C01A

LMC7221AIMX/NOPB ACTIVE SOIC D 8 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC72

21AIM

LMC7221BIM ACTIVE SOIC D 8 95 Non-RoHS

& Green Call TI Call TI -40 to 85 LMC72

21BIM

LMC7221BIM/NOPB ACTIVE SOIC D 8 95 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC72

21BIM

LMC7221BIM5 ACTIVE SOT-23 DBV 5 1000 Non-RoHS

& Green Call TI Call TI -40 to 85 C01B

LMC7221BIM5/NOPB ACTIVE SOT-23 DBV 5 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C01B

LMC7221BIM5X/NOPB ACTIVE SOT-23 DBV 5 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 C01B

LMC7221BIMX ACTIVE SOIC D 8 2500 Non-RoHS

& Green Call TI Call TI -40 to 85 LMC72

21BIM

LMC7221BIMX/NOPB ACTIVE SOIC D 8 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 85 LMC72

21BIM

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

PACKAGE OPTION ADDENDUM

www.ti.com 11-Jan-2021

Addendum-Page 2

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two

lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LMC7221AIM5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221AIM5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221AIM5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221AIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LMC7221BIM5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221BIM5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221BIM5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

LMC7221BIMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LMC7221BIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2019

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LMC7221AIM5 SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7221AIM5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7221AIM5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7221AIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LMC7221BIM5 SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7221BIM5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0

LMC7221BIM5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0

LMC7221BIMX SOIC D 8 2500 367.0 367.0 35.0

LMC7221BIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 25-Sep-2019

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

0.22

0.08 TYP

0.25

3.0

2.6

2X 0.95

1.9

1.45

0.90

0.15

0.00 TYP

5X 0.5

0.3

0.6

0.3 TYP

0 TYP

1.9

3.05

2.75

1.75

1.45

(1.1)

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/E 09/2019

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. Refernce JEDEC MO-178.

4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

0.2 C A B

INDEX AREA

PIN 1

GAGE PLANE

SEATING PLANE

0.1 C

SCALE 4.000

www.ti.com

EXAMPLE BOARD LAYOUT

0.07 MAX

ARROUND 0.07 MIN

ARROUND

5X (1.1)

5X (0.6)

(2.6)

(1.9)

2X (0.95)

(R0.05) TYP

4214839/E 09/2019

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

NOTES: (continued)

5. Publication IPC-7351 may have alternate designs.

6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

SYMM

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:15X

PKG

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

EXPOSED METAL

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK DETAILS

EXPOSED METAL

www.ti.com

EXAMPLE STENCIL DESIGN

(2.6)

(1.9)

2X(0.95)

5X (1.1)

5X (0.6)

(R0.05) TYP

SOT-23 - 1.45 mm max heightDBV0005A

SMALL OUTLINE TRANSISTOR

4214839/E 09/2019

NOTES: (continued)

7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

8. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:15X

SYMM

PKG

www.ti.com

PACKAGE OUTLINE

.228-.244 TYP

[5.80-6.19]

.069 MAX

[1.75]

6X .050

[1.27]

8X .012-.020

[0.31-0.51]

.150

[3.81]

.005-.010 TYP

[0.13-0.25]

0 - 8 .004-.010

[0.11-0.25]

.010

[0.25]

.016-.050

[0.41-1.27]

4X (0 -15 )

.189-.197

[4.81-5.00]

NOTE 3

B .150-.157

[3.81-3.98]

NOTE 4

4X (0 -15 )

(.041)

[1.04]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES:

1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.

Dimensioning and tolerancing per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed .006 [0.15] per side.

4. This dimension does not include interlead flash.

5. Reference JEDEC registration MS-012, variation AA.

.010 [0.25] C A B

PIN 1 ID AREA

SEATING PLANE

.004 [0.1] C

SEE DETAIL A

DETAIL A

TYPICAL

SCALE 2.800

www.ti.com

EXAMPLE BOARD LAYOUT

.0028 MAX

[0.07]

ALL AROUND

.0028 MIN

[0.07]

ALL AROUND

(.213)

[5.4]

6X (.050 )

[1.27]

8X (.061 )

[1.55]

8X (.024)

[0.6]

(R.002 ) TYP

[0.05]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

METAL SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

SOLDER MASK DETAILS

EXPOSED

METAL

OPENING

SOLDER MASK METAL UNDER

SOLDER MASK

DEFINED

EXPOSED

METAL

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:8X

SYMM

SEE

DETAILS

SYMM

www.ti.com

EXAMPLE STENCIL DESIGN

8X (.061 )

[1.55]

8X (.024)

[0.6]

6X (.050 )

[1.27] (.213)

[5.4]

(R.002 ) TYP

[0.05]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

9. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON .005 INCH [0.125 MM] THICK STENCIL

SCALE:8X

SYMM

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party

intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,

costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either

on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s

applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265