Page 1 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz
3W Power Amplifier Module
February 2008 - Rev 20-Feb-08 P1044-QL
P1dB, 34.5 dBm
Pout 26 dBm @ EVM = 2.5% (PAR=9.17 dB)
OIP3, 46 dBm
Gain,17 dB
Voltage, 8V
Input Internally Matched
7X7mm Surface Mount Package
Ideal for WiMAX Applications @ 5.8GHz
Features Functional Block Diagram
Absolute Maximum Ratings
Supply Voltage
RF Input Power*
Storage Temperature
Junctions Temperature
Operating Temperature
Thermal Resistance
+9.0V
+23 dBm
-55 to +125 ºC
175 ºC
-40 to 85 ºC
24 ºC/W
Electrical Characteristics (T=25 oC, Voltage Supply=8V)
General Description
The XP1044-QL is a highly linear 2-stage power amplifier
capable of 17 dB of gain, 3W of power at 1 dB compression
and is housed in an RoHS compliant 7X7mm package. The
XP1044-QL provides less than 2.5% EVM at 26 dBm output
power with 802.16 OFDM signal and peak to average ratio
9.17 dB. The input and output of the device are internally
pre-matched facilitating a simplified input and output
match. This product operates off an 8V voltage supply and
requires negative voltage which is used for current control.
XP1044-QL is specifically designed for WiMAX applications
between 4.9 GHz and 5.9 GHz.
Unless otherwise specified, the following specifications are guaranteed at room temperature in a Mimix test fixture.
Parameter Condition Min Typ Max Units
Frequency Range 4.9 5.8 5.9 GHz
Power Gain @ Pout = 27dBm 15 17.0 dB
Linear Power
@ EVM = 2.5%,
OFDM, 802.16 PAR = 9dB 26 dBm
Input Return Loss -10.0 dB
Output IP3 @ 22dBm/Tone 44 46.0 dBm
Noise Figure 5 dB
Output P1dB 34.5 dBm
Operating Current Range 1200 mA
Supply Voltage 5.0 8.0 V
Negative Voltage -0.7 V
P1044-QL
Page 2 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz
3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
XP1044-QL: ACPR vs. Output Power
WCDMA
,
Vdd = 8V, Idq1 = 440mA, Idq2 = 660mA (Idd = 1100mA)
-60
-55
-50
-45
-40
-35
-30
22.5 23 23.5 24 24.5 25 25.5 2626.5 2727.5 28
Output Power (dBm)
ACPR (dBc)
4.9GHz
5.0GHz
5.1GHz
5.2GHz
5.3GHz
5.4GHz
5.5GHz
5.6GHz
5.7GHz
5.8GHz
5.9GHz
6,0GHz
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 550mA, Idq2 = 660mA (Idd = 1210mA)
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
18 19 20 21 22 23 24 25 262728
Output Power Per Tone (dBm)
OIP3 (dBm)
4.9 GHz
5.0GHz
5.1GHz
5.2GHz
5.3GHz
5.4Hz
5.5GHz
5.6GHz
5.7GHz
5.8GHz
5.9GHz
6.0GHz
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 440mA, Idq2 = 660mA (Idd = 1100mA)
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
18 19 20 21 22 23 24 25 262728
Output Power Per Tone (dBm)
OIP3 (dBm)
4.9 GHz
5.0GHz
5.1GHz
5.2GHz
5.3GHz
5.4Hz
5.5GHz
5.6GHz
5.7GHz
5.8GHz
5.9GHz
6.0GHz
XP1044-QL: OIP3 vs. Output Power
Vdd = 8V, Idq1 = 220mA, Idq2 = 660mA (Idd = 880mA)
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
18 20 22 24 2628
Output Power Per Tone (dBm)
OIP3 (dBm)
4.9 GHz
5.0GHz
5.1GHz
5.2GHz
5.3GHz
5.4Hz
5.5GHz
5.6GHz
5.7GHz
5.8GHz
5.9GHz
6.0GHz
XP1044-QL: P1dB vs. Freq
Vdd = 8V
30
30.5
31
31.5
32
32.5
33
33.5
34
34.5
35
4.9 5 5.1 5.2 5.3 5.4 5.5 5.65.75.8 5.9 6
Freq (GHz)
P1dB(dBm)
Idq1 = 550, Idq2 = 660mA
Idq1 = 440, Idq2 = 660mA
XP1044-QL: Gain Vs Freq
Vdd = 8V
10
11
12
13
14
15
16
17
18
19
20
4.9 5 5.1 5.2 5.3 5.4 5.5 5.65.75.8 5.9 6
Freq (GHz)
Gain(dB)
Idq1= 550, Idq2 = 660mA
Idq1 = 440, Idq2 = 660mA
Typical Performance
P1044-QL
Page 3 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz
3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
Physical Dimensions
Pin Assignment:
Top View Bottom View
P1044-QL
Page 4 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz
3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
Application Circuit Schematic
App Note [1] Biasing - The XP1044-QL requires power supply sequencing. Negative voltage supply (Vgg) needs to be turned on first and
then positive voltage can be applied to the drain (Vdd). When turning off the device, the positive supply (Vdd) should be turned off first and
then negative voltage (Vgg) can be removed.
The gate voltage is adjusted in order to set the drain current to the desired level. The gate voltage required to achieve a certain current can
vary over temperature and from one device to another due to pinch-off voltage variation. Constant drain current can be achieved by
Implementing an active bias circuit which allows for temperature compensation and eliminates the effect of pinch off voltage variation.
The same current mirror circuit is implemented for each stage adding a total of 12 components at a cost of approximately $0.29
P1044-QL
Page 5 of 5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2008 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
4.9-5.9 GHz
3W Power Amplifier Module
February 2008 - Rev 20-Feb-08
Ordering Information
Description
XP1044-QL-0N00
XP1044-QL-EV1 Evaluation Board
Handling and Assembly Information
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical
processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product. This product must be
discarded in accordance with methods specified by applicable hazardous waste procedures.
- Mimix Broadband's products are not authorized for use as critical components in life support
devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As
used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions
for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package
compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base
material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and
place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF,
DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation,
but reduced reliability and life of the product due to thermal stress.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental
requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix
RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of
our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard
SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes.
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human
body and the environment. For safety, observe the following procedures: