Spec No. TQ3C-8EAF0-E1DDP46-00
SPEC
Date April 10, 2008
TYPE : TCG057VGLBB-G20
< 5.7 inch VGA transmissive color TFT with LED backlight,
Constant current circuit for LED backlight and touch panel >
CONTENTS
1. Application
2. Construction and outline
3. Mechanical specifications
4. Absolute maximum ratings
5. Electrical characteristics
6. Optical characteristics
7. Interface signals
8. Input timing characteristics
9. Backlight characteristics
10. Design guidance for analog touch panel (T/P)
11. Lot number identification
12. Warranty
13. Precautions for use
14. Reliability test data
15. Outline drawing
KYOCERA CORPORATION
KAGOSHIMA HAYATO PLANT
LCD DIVISION
 This specification is subject to change without notice.
Consult Kyocera before ordering.
Designed by: Engineering dept. Confirmed by: QA dept.
Original
Issue Date Prepared Checked
Approved
Checked
Approved
April 10, 2008
A
p
r.14
,
2008
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
-
Warning
1. This Kyocera LCD module has been specifically designed for use only in
electronic devices and industrial machines in the area of audio control,
office automation, industrial control home appliances, etc. The module
should not be used in applications where the highest level of safety and
reliability are required and module failure or malfunction of such module
results in physical harm or loss of life, as well as enormous damage or loss.
Such fields of applications include, without limitation, medical, aerospace,
communications infrastructure, atomic energy control. Kyocera expressly
disclaims any and all liability resulting in any way to the use of the module
in such applications.
2. Customer agrees to indemnity, defend and hold Kyocera harmless
from and against any and all actions, claims, damages, liabilities,
awards, costs, and expenses, including legal expenses, resulting from or
arising out of Customer's use, or sale for use, or Kyocera modules in
applications.
Caution
1. Kyocera shall have the right, which Customer hereby acknowledges, to
immediately scrap or destroy tooling for Kyocera modules for which no
Purchase Orders have been received from the Customer in a two-year period.
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
-
Revision record
Designed by : Engineering dept. Confirmed by : QA dept.
Date Prepared Checked Approved Checked Approved
Rev.No. Date Page Descriptions
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
1
M019070
1. Application
This document defines the specification of TCG057VGLBB-G20. (RoHS Compliant)
2. Construction and outline
LCD
Backlight system
Polarizer
Additional circuit
Touch panel
: Transmissive color dot matrix type TFT
: LED
: Glare treatment
: Timing controller, Power supply (3.3V input)
(with Constant current circuit for LED Backlight)
: Analog type, Non-Glare treatment
3. Mechanical specifications
3-1. Mechanical specifications of LCD
Item Specification Unit
Outline dimensions 127.2 (W)× 100.4 (H) × 6.75 (D) mm
Active area 115.2 (W) × 86.4 (H)
(14.4cm / 5.7 inch (Diagonal)) mm
Dot format 640×(B,G,R) (W) × 480 (H) dot
Dot pitch 0.06 (W) × 0.18 (H) mm
Base color *1 Normally White -
Mass 135 g
*1 Due to the characteristics of the LCD material, the color varies with environmental temperature.
3-2. Mechanical specifications of touch panel
Item Specification Unit
Input Radius-0.8 stylus or Finger -
Actuation Force 0.05〜0.8 N
Transmittance Typ. 79 %
Surface hardness Pencil hardness 2H or more according -
Anti newton’s ring
treatment None -
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
2
M019070
4. Absolute maximum ratings
4-1. Electrical absolute maximum ratings
Item Symbol Min. Max. Unit
Supply voltage for logic VDD 0 4.0 V
Input signal voltage *1 V
IN -0.3 6.0 V
Supply voltage for backlight VINB 0 6.0 V
Backlight ON-OFF BLEN 0 VINB V
Brightness adjust voltage VBRT 0 VINB V
Supply voltage for touch panel VTP 0 6.0 V
Input current of touch panel ITP 0 0.5 mA
*1 Input signal : CK, R0〜R5, G0〜G5, B0〜B5, HSYNC, VSYNC, ENAB, R/L, U/D
4-2. Environmental absolute maximum ratings
Item Symbol Min. Max. Unit
Operating temperature *1 TOP -20 70 °C
Storage temperature *2 TSTO -30 80 °C
Operating humidity *3 HOP 10 *4 %RH
Storage humidity *3 HSTO 10 *4 %RH
Vibration - *5 *5 -
Shock - *6 *6 -
*1 Operating temperature means a temperature which operation shall be guaranteed. Since display
performance is evaluated at 25°C, another temperature range should be confirmed.
*2 Temp. = -30°C＜48h , Temp. = 80°C＜168h
 Store LCD panels at normal temperature/humidity. Keep them free from vibration and shock.
An LCD panel that is kept at a low or a high temperature for a long time can be defective due to
other conditions, even if the low or high temperature satisfies the standard.
(Please refer to “Precautions for Use” for details.)
*3 Non-condensing
*4 Temp.≦40°C, 85%RH Max.
 Temp.＞40°C, Absolute humidity shall be less than 85%RH at 40°C.
*5
Frequency 10〜55 Hz
Vibration width 0.15mm
Acceleration value
(0.3〜9 m/s2)
Interval 10-55-10 Hz １minutes
2 hours in each direction X, Y, Z (6 hours total)
EIAJ ED-2531
*6 Acceleration: 490 m/s2, Pulse width: 11 ms
3 times in each direction: ±X, ±Y, ±Z
 EIAJ ED-2531
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
3
M019070
5. Electrical characteristics
5-1. LCD   Temp. = -20〜70°C
Item Symbol Condition Min. Typ. Max. Unit
Supply voltage for logic *1 VDD - 3.0 3.3 3.6 V
Current consumption for logic IDD *2 - 170 220 mA
Permissive input ripple voltage VRP - - - 100 mVp-p
VIL "Low" level 0 - 0.3VDD V
Input signal voltage *3 VIH "High" level 0.7VDD - VDD V
*1 VDD-turn-on conditions
0＜t1≦20ms

 0＜t2≦50ms

0＜t3≦1s
*2 Display pattern:
V
DD = 3.3V, Temp. = 25°C
123 456 789・・・・・・・・・・・・・・・1918 1919 1920(dot)
1
2
3
:
:
:
479
480
(dot)
■□■□■□■□■□■□■□■□■□■□
□■□■□■□■□■□■□■□■□■□■
■□■□■□■□■□■□■□■□■□■□
□■□■□■□■□■□■□■□■□■□■
■□■□■□■□■□■□■□■□■□■□
□■□■□■□■□■□■□■□■□■□■
■□■□■□■□■□■□■□■□■□■□
□■□■□■□■□■□■□■□■□■□■
*3 Input signal : CK, R0〜R5, G0〜G5, B0〜B5, HSYNC, VSYNC, ENAB, R/L, U/D
5-2. Touch panel
Item Specification
Supply voltage for touch panel 5.0V
xL〜xR : 200Ω〜1,000Ω
Terminal resistance yU〜yL : 200Ω〜800Ω
Linearity less than ±2.0%
Insulation resistance 100MΩ or more at DC25V
VDD
3.0V3.0V
0.3V
t1 t2 t3
Signal *3
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
4
M019070
6. Optical characteristics
  Measuring spot =φ6.0mm, Temp. = 25°C
Item Symbol Condition Min. Typ. Max. Unit
Rise τ r θ=φ=0° - 10 - ms
Response time
Down τ d θ=φ=0° - 25 - ms
θUPPER - 80 -
θLOWER - 80 -
deg.
φLEFT - 80 -
Viewing angle range
View deriction
: 6 o’clock
(Gray inversion)
φRIGHT
CR≧5
- 80 -
deg.
Contrast ratio CR θ=φ=0° 300 500 - -
Brightness L IF=15mA/Line 140 200 - cd/m2
x 0.56 0.61 0.66
Red y θ=φ=0°
0.32 0.37 0.42
x 0.29 0.34 0.39
Green y θ=φ=0°
0.52 0.57 0.62
x 0.09 0.14 0.19
Blue
y θ=φ=0°
0.06 0.11 0.16
x 0.28 0.33 0.38
Chromaticity
coordinates
White y θ=φ=0°
0.30 0.35 0.40
-
6-1. Definition of contrast ratio
CR(Contrast ratio) ＝
Brightness with all pixels "White"
Brightness with all pixels "Black"
6-2. Definition of response time
Brightness
100%
90%
τd
90%
10%
τr
White Black White
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
5
M019070
6-3. Definition of viewing angle
6-4. Brightness measuring points
1) Rating is defined on the average in the viewing area.
2) Measured 30 minutes after the LED is powered on. (Ambient temp. = 25°C)
‑x +x
‑y
+y
φ=0° θLOWER
θUPPER
‑x +x
‑y
θ=0°
φRIGHT
φLEFT
θdirection φdirection
+y
(dot)
(dot)
１６０×3 ３２0×3 ４８0×3
１２０
２４0
３６0
1
2
3
4
5
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
6
M019070
7. Interface signals
7-1. Pin assignment of LCD panel and LED
No. Symbol Description I/O Note
1 GND GND -
2 CK Clock signal for sampling each data signal I
3 HSYNC Horizontal synchronous signal (negative) I
4 VSYNC Vertical synchronous signal (negative) I
5 GND GND -
6 R0 RED data signal (LSB) I
7 R1 RED data signal I
8 R2 RED data signal I
9 R3
RED data signal I
10 R4
RED data signal I
11 R5
RED data signal (MSB) I
12 GND
GND -
13 G0
GREEN data signal (LSB) I
14 G1
GREEN data signal I
15 G2
GREEN data signal I
16 G3 GREEN data signal I
17 G4
GREEN data signal I
18 G5 GREEN data signal (MSB) I
19 GND
GND -
20 B0
BLUE data signal (LSB) I
21 B1
BLUE data signal I
22 B2
BLUE data signal I
23 B3
BLUE data signal I
24 B4
BLUE data signal I
25 B5
BLUE data signal (MSB) I
26 GND
GND -
27 ENAB
Signal to settle the horizontal display position (positive) I *1
28 VDD 3.3V power supply -
29 VDD 3.3V power supply -
30 R/L
Horizontal display mode select signal
L : Normal
,
H : Left / Ri
g
ht reverse mode I *2
31 U/D
Vertical display mode select signal
H : Normal
,
L : U
p
/ Down reverse mode I
32 NC
No connect -
33 VINB Power supply for LED backlight -
34 VINB Power supply for LED backlight -
35 VINB Power supply for LED backlight -
36 BLEN
Backlight ON-OFF (H : ON , L : OFF) -
37 VBRT
Brightness adjust voltage -
38 GNDB
GND for LED backlight -
39 GNDB
GND for LED backlight -
40 GNDB
GND for LED backlight -
LCD connector ： IMSA-9681S-40A-GF (IRISO)
Recommended matching FFC or FPC ： 0.5mm pitch
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
7
M019070
*1 The horizontal display start timing is settled in accordance with a rising timing of ENAB signal.
In case ENAB is fixed "Low", the horizontal start timing is determined.
Don't keep ENAB "High" during operation.
*2
R/L = L R/L = H
U/D = H U/D = H
R/L = L R/L = H
U/D = L U/D = L
7-2. Pin assignment of touch panel
No. Symbol Description
1 yL y-Lower terminal
2 xL x-Left terminal
3 yU y-Upper terminal
4 xR x-Right terminal
Touch panel side connector  ： 1.25mm pitch
Recommended matching connector ： Series FE, FFS (JST)
： KCA-K4R (DMC)
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
8
M019070
8. Input timing characteristics
8-1. Timing characteristics
Item Symbol Min Typ Max Unit Note
Frequency 1/Tc
− 25.18 28.88 MHz
Clock Duty ratio Tch/Tc 40 50 60 %
Set up time Tds 10 − − ns
Data Hold time Tdh 10 − − ns
30.0 31.8 − μs
Cycle TH
770 800 900 clock
Pulse width THp 5 30 − clock
Set up time THs 10 − − ns
Horizontal sync.
signal
Hold time THh 10 − − ns
Cycle TV 515 525 560 line
Pulse width TVp 1 3 5 line
Set up time TVs 10 − − ns
Vertical sync.
signal
Hold time TVh 10 − − ns
Pulse width TEp 640 clock
Set up time TEs 10 − − ns
Enable signal
(ENAB）
Hold time TEh 10 − − ns
HSYNC - Enable signal phase difference THE 112 144 175 clock
HSYNC - VSYNC signal phase difference THV 10 − − ns
Vertical sync. signal start position TVE 2 35 76 line
Horizontal display period THd 640 clock
Vertical display period TVd 480 line
*When ENAB is fixed at "Low", the horizontal display starts from the data of C144 (clock) as
shown in 8-3.
*When ENAB is fixed at "Low", the vertical sync. signal start position is 35 (line) as shown in 8-3.
*In case of lower frequency, the deterioration of the display quality, flicker etc., may occur.
8-2. Input Data Signals and Display position on the screen
ＧＲ
Ｄ１，ＤＨ４８０ Ｄ２，ＤＨ４８０ Ｄ３，ＤＨ４８０
Ｄ１，ＤＨ２ Ｄ２，ＤＨ２ Ｄ３，ＤＨ２
Ｂ
Ｄ１，ＤＨ１ Ｄ２，ＤＨ１ Ｄ３，ＤＨ１ Ｄ６４０，ＤＨ１
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
9
M019070
8-3. Input timing characteristics
*1 When ENAB is fixed at "Low", the horizontal display starts from the data of C144 (clock).
*2 When ENAB is fixed at "Low", the vertical sync. signal start position is 35 (line).
Data
Enablesignal
(ENAB)
Horizontalsync.
(HSYNC)
THp
TH
THs
Tch
Tds
Tdh
D1
D2
D640
Verticalinvaliddataperiod
THE
TEs
THd
TEp
TVp
THV
TVE
TV
TVd
DH1
DH2
DH480
Clocksingal
(CK)
Datasignal
(R0〜R5,G0〜G5,
B0〜B5)
Data
Enablesignal
(ENAB)
Verticalsync.
signal
(VSYNC)
Horizontal
Sync.signal
(HSYNC)
Datasignal
(R0〜R5,G0〜G5,
B0〜B5) Verticalinvaliddataperiod
Number of H-data
C1
C2
CN*1
1line
Nline*2
……
…………………
……………………
2line
0.7VDD
0.3VDD
0.7VDD
0.3VDD
0.3VDD
0.3VDD
0.7VDD
0.7VDD
0.7VDD
0.3VDD
0.3VDD
0.3VDD
0.7VDD
0.3VDD
0.3VDD
Tc
Horizontalinvaliddataperiod
0.5VDD
0.5VDD
0.7VDD
THh
TEh
0.3VDD
0.7VDD
0.3VDD
0.3VDD
0.3VDD
Clocksignal
(CK) TVs
TVh
0.7VDD
0.3VDD
Horizontalinvaliddataperiod
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
10
M019070
9. Backlight characteristics
Temp.=25℃
Item Symbol Min. Typ. Max. Unit Note
Supply voltage VINB (3.0) − (5.5) V Ta=-20〜70°C
ON-OFF (H) (0.8 VINB) - VINB V -
ON-OFF (L) BLEN 0 - (0.2VINB) V -
(14) (15) (16) VBRT=0〜(1.4)V
LED forward current *1, *2 IF (2.8) (3.0) (3.2)
mA VBRT=(2.8)V
- (440) (570) mA VINB=3.3V, IF=15mA
Supply current IINB - (280) (360) mA VINB=5.0V, IF=15mA
Operating life time *3, *4 T - (40,000) - h IF=15mA, Ta=25℃
*1 For each “LED”
*2 An input current below 5.0mA may reduce the brightness uniformity of the LED backlight.
This is because the amount of light from each LED chip is different. Therefore, please
evaluate carefully before finalizing the input current.
*3 When brightness decrease 50% of initial brightness.
*4 Life time is estimated data. (Condition : IF=15mA, Ta=25℃ in chamber)
* When you start-up, please charge in sequence of VINB->BLEN, or VBRT.
When you shut-down, please stop in sequence of BLEN and/or VBRT->VINB.
* Please do not connect the other than our backlight to this output connector on the PCB.
* In case VDD and VINB are supplied by a single power source, VDD & VINB, and GND are connected
directly and separately from the output on the power source. If the common wire are used for
V
DD & VINB, and for GND, and are split near the PCB, and connect to each LCD driving circuit
and backlight driving circuit, a flicker might be occurred due to a ripple between the both
circuit.
Right
Wrong
Output terminal
Power supply
(Customer side)
LCD
PCB
INB
GNDB
DD
GND
Output terminal
Power supply
(Customer side)
LCD
PCB
INB
GNDB
DD
GND
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
11
M019070
* VBRT-IF characteristics
10. Design guidance for analog touch panel (T/P)
10-1 Electrical (In customer's design, please remember the following considerations.)
1 Do not use the current regulated circuit.
2 Keep the current limit with top and bottom layer. (Please refer to “Electrical absolute maxim
um ratings” for details.)
3 Analog T/P can not sense two points touching separately.
4 A contact resistance is appeared at the touch point between top and bottom layer.
After this resistance has stable read of the T/P position data.
5 Because noise of inverter or peripheral circuits may interfere signal of touch panel itself
 it is necessary to design carefully in advance to avoid these noise problem.
10-2 Software
1 Do the "User Calibration".
2 "User Caribration" may be needed with long term using.
Include "User Caribration" menu in your software.
3 When drawing a line with a stylus, there may be a slight discontinuity when the stylus
passes over a spacer-dot. If necessary, please provide a compensation feature within your software.
10-3 Mounting on display and housing bezel
1 Do not use an adhesive tape to bond it on the front of T/P and hang it to the housing bezel.
2 Never expand the T/P top layer (PET-film) like a balloon by internal air pressure.
The life of the T/P will be extremely short.
3 If a dew will be on the heat-sealed area or exposed traces at the end of a flexible tail,
the migration of silver can occur. This will cause sometimes a short circuit.
V
BRT (V)
IF (mA)
(2.8)(1.4)
(15)
(3.0)
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
12
M019070
11. Lot number identification
The lot number shall be indicated on the back of the backlight case of each LCD.
TCG057VGLBB-G20 - □□ - □□ - □ MADE IN □□□□□
↓ ↓ ↓ ↓ ↓
  1 2 3 4 5

Year 2008 2009 2010 2011 2012 2013
Code 8 9 0 1 2 3
Month Jan. Feb. Mar. Apr. May Jun.
Code 1 2 3 4 5 6
Month Jul. Aug. Sep. Oct. Nov. Dec.
Code 7 8 9 X Y Z
12. Warranty
12-1. Incoming inspection
Please inspect the LCD within one month after your receipt.
12-2. Production warranty
Kyocera warrants its LCD’s for a period of 12 months from the ship date. Kyocera shall, by mutual
agreement, replace or re-work defective LCD’s that are shown to be Kyocera’s responsibility.
No1. - No5. above indicate
1. Year code
2. Month code
3. Date
4. Version Number
5. Country of origin (Japan or China)
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
13
M019070
13. Precautions for use
13-1. Installation of the LCD
1) The LCD shall be installed so that there is no pressure on the LSI chips.
2) The LCD shall be installed flat, without twisting or bending.
3) Must maintain a gap between inside of bezel and touch panel to avoid malfunction or electrode
damage of touch panel.
13-2. Static electricity
1) Since CMOS ICs are mounted directly onto the LCD glass, protection from static electricity
is required.
2) Workers should use body grounding. Operator should wear ground straps.
13-3. LCD operation
1) The LCD shall be operated within the limits specified. Operation at values outside of these limits
may shorten life, and/or harm display images.
13-4. Storage
1) The LCD shall be stored within the temperature and humidity limits specified.
Store in a dark area, and protect the LCD from direct sunlight or fluorescent light.
2) Always store the LCD so that it is free from external pressure onto it.
13-5. Usage
1) DO NOT store in a high humidity environment for extended periods. Polarizer degradation bubbles,
and/or peeling off of the polarizer may result.
2) Do not push or rub the touch panel's surface with hard to sharp objects such as knives, or the touch
panel may be scratched.
3) When the touch panel is dirty, gently wipe the surface with a soft cloth, sometimes moistened by mild
detergent or alcohol. If a hazardous chemical is dropped on the touch panel by mistake, wipe it off
right away to prevent human contact.
4) Touch panel edges are sharp. Handle the touch panel with enough care to prevent cuts
5) Always keep the LCD free from condensation during testing. Condensation may permanently spot
or stain the polarizer.
6) Do not disassemble LCD module because it will result in damage.
7) This Kyocera LCD module has been specifically designed for use in general electronic devices, but not
for use in a special environment such as usage in an active gas.Hence, when the LCD is supposed to
be used in a special environment, evaluate the LCD thoroughly beforehand and do not expose the
LCD to chemicals such as an active gas.
8) Please do not use solid-base image pattern for long hours because a temporary afterimage may
appear. We recommend using screen saver etc. in cases where a solid-base image pattern must
be used.
9) Liquid crystal may leak when the module is broken. Be careful not to let the fluid go into your eyes
and mouth. In the case the fluid touches your body; rinse it off right away with water and soap.
Spec No.
TQ3C-8EAF0-E1DDP46-00
Part No.
TCG057VGLBB-G20
Page
14
M019070
14. Reliability test data

Test item Test condition Test time Judgement
High temp.
atmosphere 80°C 240h
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
Low temp.
atmosphere -30°C 240h
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
High temp.
humidity
atmosphere
40°C 90% RH 240h
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
Temp. cycle
-30°C
R.T.
80°C
0.5h
0.5h
0.5h
10cycles
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
High temp.
operation 70°C 500h
Display function
Display quality
Current consumption
: No defect
: No defect
: No defect
Point
Activation
life
Polyacetal stylus
(R0.8)
Hitting force 3N
Hitting speed
2 time/s
one
million
times
Terminal resistance
Insulation resistance
Linearity
Actuation Force
: No defect
: No defect
: No defect
: No defect
* Each test item uses a test LCD only once. The tested LCD is not used in any other tests.
* The LCD is tested in circumstances in which there is no condensation.
* The reliability test is not an out-going inspection.
* The result of the reliability test is for your reference purpose only.
The reliability test is conducted only to examine the LCD's capability.

Spec No. TQ3C-8EAF0-E2DDP46-00
Date April 10, 2008
KYOCERA INSPECTION STANDARD
TYPE : TCG057VGLBB-G20
KYOCERA CORPORATION
KAGOSHIMA HAYATO PLANT
LCD DIVISION
Designed by : Engineering dept. Confirmed by : QA dept.
Original
Issue Date Prepared Checked
Approved
Checked
Approved
April 10, 2008
Spec No.
TQ3C-8EAF0-E2DDP46-00
Part No.
TCG057VGLBB-G20
Page
-
Revision record
Designed by : Engineering dept. Confirmed by : QA dept.
Date Prepared Checked Approved Checked Approved
Rev.No. Date Page Descriptions
Spec No.
TQ3C-8EAF0-E2DDP46-00
Part No.
TCG057VGLBB-G20
Page
1

Visuals specification
1) Note
Note
1. Customer identified anomalies not defined within this inspection standard shall be
reviewed by Kyocera, and an additional standard shall be determined by mutual
consent.
2. This inspection standard about the image quality shall be applied to any defect within
the active area and shall not be applicable to outside of the area.
General
3. Inspection conditions
Luminance
Inspection distance
Temperature
Direction
: 500 Lux min.
: 300 mm.
: 25 ± 5℃
: Directly above
Bright dot defect The dot is constantly “on” when power applied to the
LCD, even when all “Black” data sent to the screen.
Inspection tool: 5% Transparency neutral density filter.
Count dot: If the dot is visible through the filter
Don’t count dot: If the dot is not visible through the
filter
ＲＧＢＲＧＢＲＧＢ
ＲＧＢＲＧＢＲＧＢ
ＲＧＢＲＧＢＲＧＢ
 dot defect
Black dot defect The dot is constantly “off” when power applied to the
LCD, even when all “White” data sent to the screen.
Dot defect
Adjacent dot Adjacent dot defect is defined as two or more bright dot
defects or black dot defects.
ＲＧＢＲＧＢＲＧＢ
ＲＧＢＲＧＢＲＧＢ
ＲＧＢＲＧＢＲＧＢ
 dot defect
Bubble, Scratch,
Foreign particle
(Polarizer, Cell,
Backlight)
Visible operating (all pixels “Black” or “White”) and non
operating.
External
inspection
Appearance
inspection
Does not satisfy the value at the spec.
Others LED wire Damaged to the LED wire, connector, pin, functional
failure or appearance failure.
Definition of
inspection item
Definition
of size
Definition of circle size
ｄ＝(ａ＋ｂ)/2
Definition of linear size
Spec No.
TQ3C-8EAF0-E2DDP46-00
Part No.
TCG057VGLBB-G20
Page
2

2) Standard
Classification Inspection item Judgement standard
Bright dot defect Acceptable number
Bright dot spacing
: 4
: 5 mm or more
Black dot defect Acceptable number
Bright dot spacing
: 5
: 5 mm or more
Bright dot
defect Acceptable number : 2
2 dot join
Black dot
defect Acceptable number : 3
3 or more dots join Acceptable number : 0
Dot
defect
Total dot defects Acceptable number : 5 Max
Defect
(in LCD
glass)
Others White dot, Dark dot
(Circle)
Size (mm)
A
cce
p
table number
0.2 ＜d≦0.2 (Ne
g
lected)
0.2 ＜d≦0.4 5
0.4 ＜d≦0.5 3
0.5 ＜d≦0.4 0
Polarizer (Scratch)
Width (mm) Len
g
th (mm)
A
cce
p
table number
0.1 ＜
W
≦0.1 −(Neglected)
2.0 ＜L ≦5.0 (Neglected)
0.1 ＜ W ≦ 0.3 5.0 ＜L ≦5.0 0
0.3 ＜
W
≦0.3 −0
Polarizer (Bubble)
Size (mm)
A
cce
p
table number
0.2 ＜d≦0.2 (Ne
g
lected)
0.2 ＜d≦0.3 5
0.3 ＜d≦0.5 3
0.5 ＜d≦0.4 0
Foreign particle
（Circle shape）
Size (mm)
A
cce
p
table number
0.2 ＜d≦0.2 (Ne
g
lected)
0.2 ＜d≦0.4 5
0.4 ＜d≦0.5 3
0.5 ＜d≦0.4 0
External inspection
(Defect on
Polarizer or
between Polarizer
and LCD glass)
Foreign particle
（Linear shape）
Scratch
Width (mm) Len
g
th (mm)
A
cce
p
table number
0.00 ＜
W
≦0.03 −(Neglected)
2.0 ＜L ≦2.0 (Neglected)
2.0 ＜L ≦4.0 3
0.03 ＜ W ≦ 0.10
4.0 ＜L≦5.0 0
0.1 ＜ W ≦0.3 − (According to
circular shape)
Spec No.
TQ3C-8EAF0-E2DDP46-00
Part No.
TCG057VGLBB-G20
Page
3

Inspection item Judgement standard
Scratch,
Foreign particle
(Touch screen
portion)
（ W = Width, L = Length, D = Diameter = (major axis＋minor axis)/ 2）
Item Width(mm) Length(mm) Acceptable number
0.08 ＜ d ≦ 0.1 L ≦ 4 1pces within φ30mm
0.05 ＜ d ≦ 0.08 L ≦ 6 2pces within φ20mm
0.03 ＜ d ≦ 0.05 L ≦ 10 2pces within φ20mm
Scratch
d ≦ 0.03 L ≦ 20 Neglected
0.05 ＜ W ≦ 0.1 L ≦ 5 2pces within φ30mm
Foreign
（line like） W ≦ 0.05 Neglected Neglected
0.2 ＜ D ≦ 0.3 2pces within φ30mm
Foreign
（circle like） D ≦ 0.2 Neglected
Above are applied to the visible area.
Unless there are foreign particle and damage affected seriously to the
electrical performance out of the active area, we approve of this product.
Glass crack
(Touch screen
portion)
Item Size (mm)
Acceptable
number
X≦3
Y≦3
Conner
crack
Z＜t
2 pcs
/panel
X≦5
Y≦1.5
Crack in
other area
than in
corner
Z＜t
2 pcs
/side
Progressive
crack
.
0 pcs
(NG even 1pcs)
Above are applied to the visible area.
Unless there are foreign particle and damage affected seriously to the
electrical performance out of the active area, we approve of this product.
Newton’s ring Neglected.
Newton’s ring