Pb
RoHS
ECXO-2440-148.351648M
PLEASE NOTE: Due to the inherent proprietary nature of custom part numbers, certain parameters
are intentionally excluded from this specification sheet.
ECXO-2440 -148.351648M
Series
Ecliptek Custom Oscillator Nominal Frequency
148.351648MHz
ELECTRICAL SPECIFICATIONS
Nominal Frequency 148.351648MHz
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test MIL-STD-883, Method 1014 Condition A
Gross Leak Test MIL-STD-883, Method 1014 Condition C
Mechanical Shock MIL-STD-202, Method 213 Condition C
Resistance to Soldering Heat MIL-STD-202, Method 210
Resistance to Solvents MIL-STD-202, Method 215
Solderability MIL-STD-883, Method 2003
Temperature Cycling MIL-STD-883, Method 1010
Vibration MIL-STD-883, Method 2007 Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
MARKINING
ORIENTATION
2.0
MAX
5.00
±0.15
7.00
±0.15 5.08
±0.15
2.54
TYP
1.3 ±0.2
2.40 ±0.20
1
2
3
4
5
6
1.4
±0.1
PIN CONNECTION
1 Voltage Control
2 Tri-State
3 Case/Ground
4 Output
5 Complementary Output
6 Supply Voltage
LINE MARKING
1ECXO2440
2XXYZZ
XX=Ecliptek Manufacturing
Designator
Y=Last Digit Of Year
ZZ=Week of Year
www.ecliptek.com | Specification Subject to Change Without Notice | Rev A 2/16/2010 | Page 1 of 4
ECXO-2440-148.351648M
All Tolerances are ±0.1
Suggested Solder Pad Layout
Solder Land
(X6)
All Dimensions in Millimeters
0.54 (X4)
1.89
1.8 (X6)
2.0 (X6)
www.ecliptek.com | Specification Subject to Change Without Notice | Rev A 2/16/2010 | Page 2 of 4
T Min
S
T Max
S
Critical Zone
T to T
L P
Ramp-up Ramp-down
TL
TP
t 25°C to Peak
t Preheat
StL
tP
Temperature (T)
Time (t)
Recommended Solder Reflow Methods
ECXO-2440-148.351648M
High Temperature Infrared/Convection
TS MAX to TL (Ramp-up Rate) 3°C/second Maximum
Preheat
- Temperature Minimum (TS MIN) 150°C
- Temperature Typical (TS TYP) 175°C
- Temperature Maximum (TS MAX) 200°C
- Time (tS MIN) 60 - 180 Seconds
Ramp-up Rate (TL to TP)3°C/second Maximum
Time Maintained Above:
- Temperature (TL)217°C
- Time (tL)60 - 150 Seconds
Peak Temperature (TP)260°C Maximum for 10 Seconds Maximum
Target Peak Temperature (TP Target) 250°C +0/-5°C
Time within 5°C of actual peak (tp)20 - 40 seconds
Ramp-down Rate 6°C/second Maximum
Time 25°C to Peak Temperature (t) 8 minutes Maximum
Moisture Sensitivity Level Level 1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev A 2/16/2010 | Page 3 of 4
T Min
S
T Max
S
Critical Zone
T to T
L P
Ramp-up Ramp-down
TL
TP
t 25°C to Peak
t Preheat
StL
tP
Temperature (T)
Time (t)
Recommended Solder Reflow Methods
ECXO-2440-148.351648M
Low Temperature Infrared/Convection 240°C
TS MAX to TL (Ramp-up Rate) 5°C/second Maximum
Preheat
- Temperature Minimum (TS MIN) N/A
- Temperature Typical (TS TYP) 150°C
- Temperature Maximum (TS MAX) N/A
- Time (tS MIN) 60 - 120 Seconds
Ramp-up Rate (TL to TP)5°C/second Maximum
Time Maintained Above:
- Temperature (TL)150°C
- Time (tL)200 Seconds Maximum
Peak Temperature (TP)240°C Maximum
Target Peak Temperature (TP Target) 240°C Maximum 1 Time / 230°C Maximum 2 Times
Time within 5°C of actual peak (tp)10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
Ramp-down Rate 5°C/second Maximum
Time 25°C to Peak Temperature (t) N/A
Moisture Sensitivity Level Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev A 2/16/2010 | Page 4 of 4
