GO2953 CWDM DUAL OPTICAL TRANSMITTER MODULE Datasheet name: GO2953_57452_doc1.pdf Contact information: info@embrionix.com www.embrionix.com GO2953 CWDM Dual Optical Transmitter Features Description * Robust error free transmission of signals from 50Mbps to 3Gbps * Up to 50km reach in a 3Gbps CWDM installation * Available wavelengths: 1270nm ~ 1610nm, 20nm spacing * Supports video pathological patterns for SD-SDI, HD-SDI and 3G-SDI The GO2953 is a dual channel CWDM optical transmitter module designed to transmit optical serial digital signals as defined in SMPTE 297-2006. The GO2953 is specifically designed for robust performance in the presence of SDI pathological patterns for SMPTE 259M, SMPTE 344M, SMPTE 292M and SMPTE 424M serial rates. * Hot-pluggable * Two independent laser disable pins * Digital diagnostics and control via I2C interface including: Monitoring laser bias current, average output power, supply voltage and temperature Alarm reporting with self shut down when transmitter is at fault Module ID polling * Single +3.3V power supply * Low power consumption -- typically 680mW * RoHS compliant * Operating temperature range: 0C to 70C * 56.5mm x 13.4mm x 8.6mm SFP Package * SMPTE 297-2006 compatible The GO2953 contains two independent DFB laser transmitters, each designed to provide error-free transmission of signals from 50Mbps to 3Gbps. The GO2953 is hot-pluggable with typical power consumption of 680mW using a single power supply of +3.3V. The GO2953 provides extensive operational status monitoring through an I2C interface. For each transmitter channel, output optical power and bias current are monitored. Other operating conditions such as supply voltage and operating temperature are also monitored. If a parameter monitored is outside the pre-defined range, the alarm flag associated with the parameter will be raised. Applications * SMPTE 297-2006 compatible electrical-to-optical interfaces * High-density video routers GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 www.gennum.com 1 of 23 Proprietary & Confidential Revision History Version ECR Date 0 157039 November 2011 1 157987 April 2012 Changes and/or Modifications New document. Updated extinction ratio in Table 3-2. Contents Features.................................................................................................................................................................1 Description...........................................................................................................................................................1 Revision History .................................................................................................................................................2 1. Functional Block Diagram..........................................................................................................................3 2. Pin Specifications ..........................................................................................................................................4 2.1 Pin Configuration .............................................................................................................................4 2.2 Pin Descriptions ................................................................................................................................4 2.3 Host Board Power Supply Requirements .................................................................................5 2.4 Optical Connector Requirements ................................................................................................6 3. Product Specifications .................................................................................................................................7 3.1 Absolute Maximum Ratings ..........................................................................................................7 3.2 Optical Performance Specifications ...........................................................................................7 3.3 DC Electrical Specifications ..........................................................................................................9 3.4 AC Electrical Specifications ..........................................................................................................9 3.5 Supporting Circuit Specifications ............................................................................................ 10 3.5.1 In-Rush Current Control Circuit ................................................................................... 10 3.5.2 Digital Diagnosis ................................................................................................................ 10 4. Application Reference Design ............................................................................................................... 17 4.1 Typical Application Circuit ........................................................................................................ 17 5. References and Relevant Standards .................................................................................................... 18 6. Package Information ................................................................................................................................. 19 6.1 Package Dimensions ..................................................................................................................... 19 6.2 PCB Layout Recommendations ................................................................................................. 20 6.3 Marking Information .................................................................................................................... 21 6.4 Ordering Information ................................................................................................................... 22 GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 2 of 23 Proprietary & Confidential 1. Functional Block Diagram Feedback Differential Electrical Input Tx1_Disable I2C Bus TOSA_1 Laser + PINmon Laser Driver Tx provision and analog maintenance Digital Diagnostics Tx2_Disable Differential Electrical Input 1270 - 1610nm TOSA_2 Laser + PINmon Laser Driver 1270 - 1610nm Feedback Figure 1-1: GO2953 Functional Block Diagram GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 3 of 23 Proprietary & Confidential 2. Pin Specifications 2.1 Pin Configuration Towards Bezel TX1_DIS 20 NC TD1- 19 3 NC TD1+ 18 4 VEE VEE 17 5 I2C CLK VCC_TX1 16 1 VEE 2 VCC_TX2 15 VEE VEE 14 8 TD2+ NC 13 9 TD2- NC 12 10 TX2_DIS VEE 11 6 I C DATA 7 2 Towards ASIC Figure 2-1: Pin Configuration for GO2953 2.2 Pin Descriptions Table 2-1: Pin Descriptions Number Name Type 1 VEE Ground 2 NC No Connect No Connection 3 NC No Connect No Connection 4 VEE Ground 5 I2C CLK Digital (Input) I2C Clock 6 I2C DATA Digital (Bi-Directional) I2C Data GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 Description Ground connection Ground connection 4 of 23 Proprietary & Confidential Table 2-1: Pin Descriptions (Continued) Number Name Type Description 7 VEE Ground 8 TD2+ Input Positive Differential Input. Internally AC-coupled. 9 TD2- Input Negative Differential Input. Internally AC-coupled. 10 TX2_Dis Digital (Input) 11 VEE Ground 12 NC No Connect No Connection 13 NC No Connect No Connection 14 VEE Ground 15 VCC_TX2 Power Transmitter Power Supply 16 VCC_TX1 Power Transmitter Power Supply 17 VEE Ground 18 TD1+ Input Positive Differential Input. Internally AC-coupled. 19 TD1- Input Negative Differential Input. Internally AC-coupled. 20 TX1_Dis Digital (Input) Ground connection Transmitter Disable. The bias current and modulation current are turned off if TX2_DIS = HIGH. Internal 4.7k pull-up. Ground connection Ground connection Ground connection Transmitter Disable. The bias current and modulation current are turned off if TX1_DIS = HIGH. Internal 4.7k pull-up. 2.3 Host Board Power Supply Requirements The host board is required to provide a regulated and filtered power supply of 3.3V +/5% V for the GO2953 via the on board SFP connector. The host board is required to filter the VCC_TX power supply as recommended by the SFP MSA. Figure 2-2 shows the recommended board supply filtering. When the host board is loaded with a resistive load in place of the SFP module and sourcing the maximum rated current, the peak-to-peak power supply noise measured on the SFP connector should comply to Table 2-2. GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 5 of 23 Proprietary & Confidential 1H V CC_Tx1 0.1F 10F 1H V 3.3V CC_Tx2 0.1F GO2953 10F 0.1F 10F Host Board Figure 2-2: Recommended Host Board Supply Filtering Table 2-2: Host Board Power Supply Noise Requirement at VCCR Frequency (MHz) Peak-to-Peak Noise Amplitude (%) 0.02-1 2 1-10 3 2.4 Optical Connector Requirements An LC connector with PC/UPC polish is required for each port. GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 6 of 23 Proprietary & Confidential 3. Product Specifications 3.1 Absolute Maximum Ratings Table 3-1 lists the absolute maximum ratings for the GO2953. Conditions exceeding the limits listed may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3-1: Absolute Maximum Ratings Parameter Conditions Value/Units Supply Voltage - 4V Operating Case Temperature - -20C < TCASE < 80C Storage Temperature - -40C < TSTG < 100C ESD tolerance on all pins - 1 kV HBM Relative Humidity (non-condensing) - 5% - 95% RH 3.2 Optical Performance Specifications Table 3-2 lists the optical performance specifications for the GO2953. Table 3-2: Optical Performance Specifications Parameter Symbol Condition Min Typ Max Units Notes Wavelength - X-6.5 X X+6.5 nm 2 Spectral Line Width - - - 0.2 1 nm - POUT - 0 +2.5 +5 dBm - ER - 8 - - dB - System Average Optical Output Power Extinction Ratio GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 7 of 23 Proprietary & Confidential Table 3-2: Optical Performance Specifications (Continued) Parameter Optical Signal Intrinsic Jitter Symbol - Condition Min Typ Max Units Notes Measured with PRBS - 40 60 ps 3 SMPTE 424M 2.97Gbps Pathological - 50 90 ps 3 SMPTE 292M 1.485Gbps Pathological - 60 120 ps 3 SMPTE 259M 270Mbps Pathological - 110 200 ps 3 SMPTE 424M 2.97Gbps - 130 180 ps 3 SMPTE 292M 1.485Gbps - 175 270 ps 3 SMPTE 259M 270Mbps - 300 800 ps 3 SMPTE 424M 2.97Gbps - 130 180 ps 3 SMPTE 292M 1.485Gbps - 175 270 ps 3 SMPTE 259M 270Mbps - 300 800 ps 3 223-1 and colour bar test signal at 2.97Gbps, 1.485Gbps, 270Mbps Optical Signal Rise Time tr (20% to 80%) Optical Signal Fall Time tf (20% to 80%) NOTES: 1. Outside the specified range, performance is not guaranteed. 2. X = Centre Wavelength: 1271, 1291, 1311, 1331, 1351, 1371, 1391, 1411, 1431, 1451, 1471, 1491, 1511, 1531, 1551, 1571, 1591 & 1611nm 3. Measured following a fourth-order Bessel-Thompson filter with a bandwidth of 0.75 x clock frequency corresponding to the serial data rate. GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 8 of 23 Proprietary & Confidential 3.3 DC Electrical Specifications Table 3-3 lists the DC electrical specifications for the GO2953. Table 3-3: DC Electrical Specifications Parameter Symbol Condition Min Typ Max Units Notes TCASE - 0 - 70 C 1,3 VCC - 3.13 3.3 3.47 V 1,3 Total Power Consumption - - - 650 1000 mW 3 Input Data Amplitude - - 0.2 - 1.2 Vpp 2,3 Laser Bias Current Monitoring Accuracy - - -1 - +1 dB 3 Laser Power Monitoring Accuracy - - -1 - +1 dB 3 System Operating Temperature Range Power Supply Voltage Laser NOTES: 1. Outside the specified range, performance is not guaranteed. 2. AC coupled 50 single-ended termination. 3. Specifications apply at the beginning of life. 3.4 AC Electrical Specifications Table 3-4 lists the AC electrical specifications for the GO2953. Table 3-4: AC Electrical Specifications Parameter Bit Rate Symbol Condition Min Max Units BR - 50 3000 Mbps Tx_Disable Assert Time t_off Time from rising edge of TX_DIS to when the optical output falls below 10% of nominal - 10 s Tx_Disable Negate Time t_on Time from falling edge of TX_DIS to when the modulated optical output rises above 90% of nominal - 1 ms Time to Initialize t_init From power on - 300 ms - 400 kHz Serial ID Clock Rate f_serial_clock GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 - 9 of 23 Proprietary & Confidential 3.5 Supporting Circuit Specifications 3.5.1 In-Rush Current Control Circuit Due to the hot-pluggable requirement, the GO2953 has built-in circuits to limit the in-rush current upon hot insertion. The specifications of the in-rush limiting circuits are summarized in Table 3-5. Table 3-5: In-rush Current Limiting Circuits Specifications Parameter Value Max. In-rush current ramp rate 50mA/ms Max. In-rush current 30mA over steady state 3.5.2 Digital Diagnosis 3.5.2.1 I2C Bus Interface The I2C bus interface uses the 2-wire serial CMOS E2PROM protocol. The serial interface meets the following specifications: 1. Support a maximum clock rate of 400kHz. 2. Input/Output levels comply with LVCMOS/LVTTL or compatible logics. Low: 0 - 0.8V High: 2.0 - 3.3V Undefined: 0.8 - 2.0V 3.5.2.2 Serial Interface Memory Map Module identification and diagnostic information is accessible through the address map shown in Table 3-6. Block addresses starting with the letter `A' refer to Channel 1 and block addresses starting with the letter `B' refer to Channel 2. Table 3-6: Serial Interface Memory Map Address Size Name Description and Value of the Field Base ID Fields (Block Address: A0h) 0 1 Identifier Type of serial transceiver. 81h 1 1 Ext. Identifier Extended identifier of type of serial transceiver. 04h 2 1 Connector Code for connector type. 07h for LC connectors. GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 10 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size Name Description and Value of the Field 3 1 Standards Compliance 41h, for SMPTE259M/344M/292M/424M and SMPTE 297. 4-10 8 Transceiver Code Code for electronic compatibility or optical compatibility. Not applicable for GO2953. 11 1 Encoding Code for serial encoding algorithm. Value: 03H for NRZ. 12 1 BR, Nominal Nominal bit rate, units of 100Mbps, 1Eh for 3Gbps. 13 1 Reserved Xxh 14 1 Length(9mm) km Link length supported for standard SMF, units of km, 32h for 50km. 15 1 Length(9mm) Link length supported for standard SMF, units of 100 m, 00h 16 1 Length (50mm) Link length supported for 50/125mm fiber, units of 10m. 00h 17 1 Length (62.5mm) Link length supported for 62.5/125mm fiber, units of 10m. 00h 18 1 Length (Copper) Link length supported for copper, units of meters. 00h 19 1 Reserved Xxh 20-35 16 Vendor name SFP with OM transceiver vendor name (ASCII). G E N N U M 20 1 G 47h 21 1 E 45h 22 1 N 4Eh 23 1 N 4Eh 24 1 U 55h 25 1 M 4Dh 26-35 10 - 20h for each byte 36 1 Reserved - 37-39 3 Vendor OUI SFP with OM transceiver vendor IEEE company ID. 00 0A DF 40-55 16 Vendor PN Part number provided by SFP with OM transceiver vendor. G O 2 9 5 3. 40 1 G 47h 41 1 O 4Fh 42 1 2 32h 43 1 9 39h GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 11 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size Name Description and Value of the Field 44 1 5 35h 45 1 3 33h 46 1 X Model dependent. 47 1 X Model dependent. 48 1 Y Model dependent. 49 1 Y Model dependent. 50 1 C 43h 51 1 H 48h 52-55 4 - 20h for each byte. 56-58 3 - Reserved 59 1 Vendor Rev Revision level for part number provided by vendor. 60 1 Wavelength1 XX for the middle two digits of the wavelength of Channel #1. 61 1 Wavelength2 YY for the middle two digits of the wavelength of Channel #2. 62 1 Reserved Xxh 63 1 CC_BASE Check code for Base ID Fields (The value of the lower 8 bits of the sum of the contents from address 0 to 62). 64-65 2 Options Indicates which optional SFP with OM signals are implemented. 64 1 - Xxh 65 1 - x001100xh 66 1 BR, max Upper bit rate margin, units of %, 5h. 67 1 BR, min Lower bit rate margin, units of %, 5Fh. 68-83 16 Vendor SN Serial number provided by vendor (ASCII) 84-85 2 Year Manufacturing date code (ASCII). 86-87 2 Month Manufacturing date code (ASCII). 88-89 2 Day Manufacturing date code (ASCII). 90-91 2 Blank - 92 1 Calibration flag 20h for calibrated average output power 93 1 - E0h, Enhanced alarm/warning flags. 94 1 Reserved Xxh GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 12 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size Name Description and Value of the Field 95 1 CC_EXT Check code for the Extended ID Fields (The value of the lower 8 bits of the sum of the contents from address 64 to 94) 96-255 160 Reserved - Alarm and Warning Thresholds (Block Address: A2h and B2h) 0-1 2 Temp High Alarm MSB at lower address. 70C ambient 2-3 2 Temp Low Alarm MSB at lower address. 0C ambient 4-5 2 Temp High Warning MSB at lower address. 65C ambient 6-7 2 Temp Low Warning MSB at lower address. 5C ambient 8-9 2 Supply Voltage High Alarm MSB at lower address. 3.6V 10-11 2 Supply Voltage Low Alarm MSB at lower address. 3.0V 12-13 2 Supply Voltage High Warning MSB at lower address. 3.47V 14-15 2 Supply Voltage Low Warning MSB at lower address. 3.14V 16-17 2 Laser Bias High Alarm MSB at lower address. 100mA. 18-19 2 Laser Bias Low Alarm MSB at lower address. 5mA. 20-21 2 Laser Bias High Warning MSB at lower address. 90mA. 22-23 2 Laser Bias Low Warning MSB at lower address. 10mA 24-25 2 Tx Power High Alarm MSB at lower address. 5.5dBm 26-27 2 Tx Power Low Alarm MSB at lower address. 0dBm 28-29 2 Tx Power High Warning MSB at lower address. 5dBm 30-31 2 Tx Power Low Warning MSB at lower address. 0.5dBm 32-95 65 Reserved. - 96 1 Temperature MSB Internally measured module temperature 97 1 Temperature LSB Internally measured module temperature GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 13 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size Name Description and Value of the Field 98 1 Vcc MSB Internally measured module supply voltage 99 1 Vcc LSB Internally measured module supply voltage 100 1 Laser Bias MSB Internally measured laser bias current. 101 1 Laser Bias LSB Internally measured laser bias current. 102 1 Tx Power MSB Internally measured Tx Power. 103 1 Tx Power LSB Internally measured Tx Power. 104-109 11 Reserved - 110 1 Tx Disable State Bit 7: State of TX_DIS input pin Tx Disable Select Bit 6: Read/write bit that allows software disable of laser. Writing "1" disables laser Reserved Bit 5 Reserved Bit 4 Reserved Bit 3 Tx Fault Bit 2: State of TX_FAULT N/A Bit 1 Data_Ready Bit 0 Conversion Update - Temp Update Bit 7 goes to high after a temperature update Vcc Update Bit 6 goes to high after a Vcc update Mon1 Update Bit 5 goes to high after a Tx bias current update Mon2 Update Bit 4 goes to high after a Tx power update Mon3 Update Bit 3 goes to high after a Tx modulation current update. Reserved Bit 0 to Bit 2. 111 1 GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 14 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size 112 1 113 114-115 1 2 Name Description and Value of the Field Temp High Alarm Flag Bit 7, set when the internal temperature exceeds the high temp alarm threshold. Temp Low Alarm Flag Bit 6, set when the internal temperature goes below the low temp alarm threshold. Supply Voltage High Alarm Flag Bit 5, set when the internal Vcc exceeds the supply voltage high alarm threshold. Supply Voltage Low Alarm Flag Bit 4, set when the internal Vcc goes below the supply voltage low alarm threshold. Laser Bias High Alarm Flag Bit 3, set when the monitored laser bias current exceeds the laser bias high alarm threshold. Laser Bias Low Alarm Flag Bit 2, set when monitored laser bias current goes below the laser bias low alarm threshold. Tx Power High Alarm Flag Bit 1, set when the monitored Tx power exceeds the Tx power high alarm threshold. Tx Power Low Alarm Flag Bit 0, set when monitored Tx power current goes below the Tx power low alarm threshold. Mod Current High Alarm Flag Bit 7, set when the monitored laser modulation current exceeds the laser bias high alarm threshold. Mod Current Low Alarm Flat Bit 6, set when monitored laser bias current goes below the laser modulation low alarm threshold. Reserved Bit 0 - 5. Reserved - GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 15 of 23 Proprietary & Confidential Table 3-6: Serial Interface Memory Map (Continued) Address Size 116 1 117 118-127 1 10 Name Description and Value of the Field Temp High Warning Flag Bit 7, set when the internal temperature exceeds the high temp warning threshold. Temp Low Warning Flag Bit 6, set when the internal temperature goes below the low temp warning threshold. Supply Voltage High Warning Flag Bit 5, set when the internal Vcc exceeds the supply voltage high warning threshold. Supply Voltage Low Warning Flag Bit 4, set when the internal Vcc goes below the supply voltage low warning threshold. Laser Bias High Warning Flag Bit 3, set when the monitored laser bias current exceeds the laser bias high warning threshold. Laser Bias Low Warning Flag Bit 2, set when monitored laser bias current goes below the laser bias low warning threshold. Tx Power High Warning Flag Bit 1, set when the monitored Tx power exceeds the Tx power high warning threshold. Tx Power Low Warning Flag Bit 0, set when monitored Tx power current goes below the Tx power low warning threshold. Mod Current High Warning Flag Bit 7, set when the monitored laser modulation current exceeds the laser bias high alarm threshold. Mod Current Low Warning Flag Bit 6, set when monitored laser bias current goes below the laser modulation low alarm threshold. Reserved Bit 0 - 5 Reserved - User Writeable Area - Reserved - Vendor Specific ID Fields 128-247 120 248-255 8 GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 16 of 23 Proprietary & Confidential 4. Application Reference Design 4.1 Typical Application Circuit Figure 4-1 shows a typical application circuit for the GO2953. 1 VCC_3V3 VCC_3V3 2 3 10k 10k 4 5 2 I C CLK 6 2 I C DATA 7 TD2+ From GS2965 Reclocker Differential TD2TX2_DIS 8 9 10 GO2953 VEE TX1_DIS NC TD1- NC TD1+ VEE VEE 2 I C CLK 2 I C DATA VEE VCC_TX1 VCC_TX2 VEE TD2+ NC TD2- NC TX2_DIS VEE 20 TX1_DIS 19 TD1- 18 TD1+ Differential From GS2965 Reclocker 17 16 100nF 15 1H 1H 14 13 VCC_3V3 10uF 100nF 10F 100nF 10F 12 11 Figure 4-1: Typical Application Circuit GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 17 of 23 Proprietary & Confidential 5. References and Relevant Standards Table 5-1: References and Relevant Standards INF-8074i Rev 1.0 SFP (Small Formfactor Pluggable) Transceiver SMPTE 259M-2008 SDTV Digital Signal/Data - Serial Digital Interface SMPTE 292M-2008 1.5 Gb/s Signal / Data Serial Interface SMPTE 297-2006 Serial Digital Fiber Transmission System for SMPTE 259M, SMPTE 344M, SMPTE 292 and SMPTE 424M Signals SMPTE 344M-2000 540 Mb/s Serial Digital Interface SMPTE 424M-2006 3 Gb/s Signal/Data Serial Interface ITU-T G.694.2 Spectral grids for WDM applications: CWDM wavelength grid GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 18 of 23 Proprietary & Confidential 6. Package Information 6.1 Package Dimensions A common mechanical outline, as shown in Figure 6-1, is used for all SFP modules. Figure 6-1: Common SFP Package Outline GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 19 of 23 Proprietary & Confidential 6.2 PCB Layout Recommendations Figure 6-2: Host PCB Layout - Part 1 GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 20 of 23 Proprietary & Confidential Figure 6-3: Host PCB Layout - Part 2 6.3 Marking Information Table 6-1: Marking Information Label Code XXYY ZZZZZZZ Description 4-digit wavelength code - see Table 6-2: Ordering Information. 7-digit serial number UUUU Channel 1 wavelength in nanometers VVVV Channel 2 wavelength in nanometers YYYY Year of manufacture WW Week of manufacture Figure 6-4: GO2953 Marking Information GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 21 of 23 Proprietary & Confidential 6.4 Ordering Information Table 6-2: Ordering Information Part Number Package Wavelength Temperature Range GO2953-2729CH SFP Ch1: 1271nm 0C to 70C Ch2: 1291nm GO2953-3133CH SFP Ch1: 1311nm 0C to 70C Ch2: 1331nm GO2953-3537CH SFP Ch1: 1351nm 0C to 70C Ch2: 1371nm GO2953-3941CH SFP Ch1: 1391nm 0C to 70C Ch2: 1411nm GO2953-4345CH SFP Ch1: 1431nm 0C to 70C Ch2: 1451nm GO2953-4749CH SFP Ch1: 1471nm 0C to 70C Ch2: 1491nm GO2953-5153CH SFP Ch1: 1511nm 0C to 70C Ch2: 1531nm GO2953-5557CH SFP Ch1: 1551nm 0C to 70C Ch2: 1571nm GO2953-5961CH SFP Ch1: 1591nm 0C to 70C Ch2: 1611nm GO2953-3155CH SFP Ch1: 1310nm 0C to 70C Ch2: 1550nm GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 22 of 23 Proprietary & Confidential DOCUMENT IDENTIFICATION CAUTION APPLICATION NOTE ELECTROSTATIC SENSITIVE DEVICES Information relating to this product and the application or design described herein is believed to be reliable, however such information is provided as a guide only and Gennum assumes no liability for any errors in this document, or for the application or design described herein. Gennum reserves the right to make changes to the product or this document at any time without notice. DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION GENNUM CORPORATE HEADQUARTERS Phone: +1 (905) 632-2996 Fax: +1 (905) 632-2055 4281 Harvester Road, Burlington, Ontario L7L 5M4 Canada E-mail: corporate@gennum.com www.gennum.com CANADA JAPAN KK TAIWAN Suite 320, 3553 31st St. N.W. Calgary, Alberta T2L 2K7 Canada Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo, 160-0023 Japan 6F-4, No.51, Sec.2, Keelung Rd. Sinyi District, Taipei City 11052 Taiwan R.O.C. Phone: +1 (403) 284-2672 Fax: +1 (905) 632-2055 415 Legget Drive, Suite 200 Kanata, Ontario K2K 2B2 Canada Phone: +1 (613) 270-0458 Fax: +1 (613) 270-0429 GERMANY Phone: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 E-mail: gennum-japan@gennum.com Web Site: http://www.gennum.co.jp MEXICO Venustiano Carranza 122 Int. 1 Centro, Aguascalientes Mexico CP 20000 Gennum Canada Limited Niederlassung Deutschland Munchen, Germany Phone: +1 (416) 848-0328 Phone: +49 89 309040 290 Fax: +49 89 309040 293 E-mail: gennum-germany@gennum.com 691 South Milpitas Blvd., Suite #200 Milpitas, CA 95035 United States INDIA Phone: +1 (408) 934-1301 Fax: +1 (408) 934-1029 E-mail: naw_sales@gennum.com #208(A), Nirmala Plaza, Airport Road, Forest Park Square Bhubaneswar 751009 India Phone: +91 (674) 65304815 Fax: +91 (674) 259-5733 NORTH AMERICA WESTERN REGION NORTH AMERICA EASTERN REGION 4281 Harvester Road Burlington, Ontario L7L 5M4 Canada Phone: +1 (905) 632-2996 Fax: +1 (905) 632-2055 E-mail: nae_sales@gennum.com Phone: (886) 2-8732-8879 Fax: (886) 2-8732-8870 E-mail: gennum-taiwan@gennum.com UNITED KINGDOM South Building, Walden Court Parsonage Lane, Bishop's Stortford Hertfordshire, CM23 5DB United Kingdom Phone: +44 1279 714170 Fax: +44 1279 714171 2, West Point Court, Great Park Road Bradley Stoke, Bristol BS32 4PY Great Britain Phone: +44 1454 462200 Fax: +44 1454 462201 SNOWBUSH IP - A DIVISION OF GENNUM 439 University Ave. Suite 1700 Toronto, Ontario M5G 1Y8 Canada Phone: +1 (416) 925-5643 Fax: +1 (416) 925-0581 E-mail: sales@snowbush.com Web Site: http://www.snowbush.com Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the circuits or devices described herein. The sale of the circuit or device described herein does not imply any patent license, and Gennum makes no representation that the circuit or device is free from patent infringement. All other trademarks mentioned are the properties of their respective owners. GENNUM and the Gennum logo are registered trademarks of Gennum Corporation. (c) Copyright 2011 Gennum Corporation. All rights reserved. www.gennum.com GO2953 CWDM Dual Optical Transmitter Data Sheet 57452 - 1 April 2012 23 of 23 23 Proprietary & Confidential IMPORTANT NOTICE Embrionix Design inc. and its subsidiaries (Embrionix) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to Embrionix's terms and conditions of sale supplied at the time of order acknowledgment. Embrionix warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Embrionix's standard warranty. Testing and other quality control techniques are used to the extent Embrionix deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Embrionix assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using Embrionix SFP and emSFP. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. Embrionix does not warrant or represent that any license, either express or implied, is granted under any Embrionix patent right, copyright, mask work right, or other Embrionix intellectual property right relating to any combination, machine, or process in which Embrionix products or services are used. Information published by Embrionix regarding third-party products or services does not constitute a license from Embrionix to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from Embrionix under the patents or other intellectual property of Embrionix. Reproduction of Embrionix information in Embrionix data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. Embrionix is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of Embrionix products or services with statements different from or beyond the parameters stated by Embrionix for that product or service voids all express and any implied warranties for the associated Embrionix product or service and is an unfair and deceptive business practice. Embrionix is not responsible or liable for any such statements. Embrionix products are not authorized for use in safety-critical applications (such as life support) where a failure of the Embrionix product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Embrionix products in such safety-critical applications, notwithstanding any applicationsrelated information or support that may be provided by Embrionix. Further, Buyers must fully indemnify Embrionix and its representatives against any damages arising out of the use of Embrionix products in such safety-critical applications. Embrionix products are neither designed nor intended for use in military/aerospace applications or environments unless the Embrionix products are specifically designated by Embrionix as military-grade. Only products designated by Embrionix as military-grade meet military specifications. Buyers acknowledge and agree that any such use of Embrionix products which Embrionix has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. Embrionix products are neither designed nor intended for use in automotive applications or environments unless the specific Embrionix products are designated by Embrionix as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, Embrionix will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Embrionix products and Embrionix contact information: General website: Sales contact information: http://www.embrionix.com sales@embrionix.com Contact information: Telephone: http://www.embrionix.com/Contact.aspx 1.450.688.8171