LM2902EP Low Power Quad Operational Amplifiers General Description Advantages The LM2902 consists of four independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. n Eliminates need for dual supplies n Four internally compensated op amps in a single package n Allows directly sensing near GND and VOUT also goes to GND n Compatible with all forms of logic n Power drain suitable for battery operation Application areas include transducer amplifiers, DC gain blocks and all the conventional op amp circuits which now can be more easily implemented in single power supply systems. For example, the LM2902 can be directly operated off of the standard +5V power supply voltage which is used in digital systems and will easily provide the required interface electronics without requiring the additional 15V power supplies. ENHANCED PLASTIC * Extended Temperature Performance of -40C to +85C * * * * * Baseline Control - Single Fab & Assembly Site Process Change Notification (PCN) Qualification & Reliability Data Solder (PbSn) Lead Finish is standard Enhanced Diminishing Manufacturing Sources (DMS) Support Unique Characteristics n In the linear mode the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage n The unity gain cross frequency is temperature compensated n The input bias current is also temperature compensated Features n Internally frequency compensated for unity gain n Large DC voltage gain 100 dB n Wide bandwidth (unity gain) 1 MHz (temperature compensated) n Wide power supply range: Single supply 3V to 26V or dual supplies 1.5V to 13V n Very low supply current drain (700 A) -- essentially independent of supply voltage n Low input biasing current 45 nA (temperature compensated) n Low input offset voltage 2 mV and offset current: 5 nA n Input common-mode voltage range includes ground n Differential input voltage range equal to the power supply voltage n Large output voltage swing 0V to V+ - 1.5V Applications n Selected Military Applications n Selected Avionics Applications Ordering Information PART NUMBER VID PART NUMBER NS PACKAGE NUMBER (Note 3) LM2902MEP V62/04744-01 M14A (Notes 1, 2) TBD TBD Note 1: For the following (Enhanced Plastic) version, check for availability: LM2902MXEP, LM2902MTEP, LM2902MTXEP, LM2902NEP. Parts listed with an "X" are provided in Tape & Reel and parts without an "X" are in Rails. Note 2: FOR ADDITIONAL ORDERING AND PRODUCT INFORMATION, PLEASE VISIT THE ENHANCED PLASTIC WEB SITE AT: www.national.com/ mil Note 3: Refer to package details under Physical Dimensions (c) 2005 National Semiconductor Corporation DS201140 www.national.com LM2902EP Low Power Quad Operational Amplifiers February 2005 LM2902EP Connection Diagram Dual-In-Line Package 20114001 Top View See NS Package Number M14A or N14A Schematic Diagram (Each Amplifier) 20114002 www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage, V+ 26V Differential Input Voltage 26V Input Voltage -0.3V to +26V Input Current (VIN < -0.3V) (Note 6) 50 mA Power Dissipation (Note 4) Molded DIP 1130 mW Small Outline Package 800 mW Output Short-Circuit to GND (One Amplifier) (Note 5) V+ 15V and TA = 25C Continuous Operating Temperature Range -40C to +85C Storage Temperature Range -65C to +150C Lead Temperature (Soldering, 10 seconds) 220C Soldering Information Small Outline Package Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C ESD Tolerance (Note 14) 250V Electrical Characteristics V+ = +5.0V, unless otherwise stated (Notes 7, 8) Parameter Conditions Input Offset Voltage (Note 9) TA = 25C Input Bias Current (Note 10) IIN(+) or IIN(-), VCM = 0V, TA = 25C Input Offset Current IIN(+) or IIN(-), VCM = 0V, TA = 25C + LM2902 Min Max 2 7 mV 45 250 nA 5 50 nA V+-1.5 V + Input Common-Mode Voltage Range (Note 11) V V = 26V, TA = 25C Supply Current Over Full Temperature Range 0 RL = On All Op Amps mA + V = 26V) 1.5 3 V+ = 5V 0.7 1.2 Large Signal V+ = 15V, RL 2k, Voltage Gain (VO = 1V to 11V), TA = 25C Common-Mode DC, VCM = 0V to V+ - 1.5V, Rejection Ratio TA = 25C Power Supply V+ = 5V to 26V RejectionRatio TA = 25C Amplifier-to-Amplifier f = 1 kHz to 20 kHz, TA = 25C Coupling (Note 12) (Input Referred) Output Current Source VIN+ = 1V, VIN- = 0V, 25 100 V/mV 50 70 dB 50 100 dB -120 dB 20 40 10 20 12 50 V+ = 15V, VO = 2V, TA = 25C Sink Units Typ VIN- = 1V, VIN+ = 0V, mA V+ = 15V, VO = 2V, TA = 25C VIN- = 1V, VIN+ = 0V, A V+ = 15V, VO = 200 mV, TA = 25C 3 www.national.com LM2902EP Absolute Maximum Ratings (Note 13) LM2902EP Electrical Characteristics (Continued) V+ = +5.0V, unless otherwise stated (Notes 7, 8) Parameter LM2902 Conditions Min Short Circuit to Ground (Note 5) V+ = 15V, TA = 25C Input Offset Voltage (Note 9) Typ 40 VOS Drift RS = 0 7 Input Offset Current IIN(+) - IIN(-), VCM = 0V 45 IOS Drift RS = 0 10 40 Input Bias Current IIN(+) or IIN(-) Input Common-Mode Voltage Range (Note 11) V+ = 26V Large Signal Voltage Gain V+ = +15V (VOSwing = 1V to 11V) 0 RL 2 k Output Voltage VOH V = 26V VOL V+ = 5V, RL = 10 k Output Current Source VO = 2V 23 60 mA mV V/C 200 10 500 nA V+-2 V V/mV V 100 VIN- = +1V, mV 20 VIN- = 0V, V+ = 15V Sink nA pA/C 24 5 VIN+ = +1V, Units 10 15 RL = 10 k + Swing Max mA 5 8 VIN+ = 0V, V+ = 15V Note 4: For operating at high temperatures, the LM2902EP must be derated based on a +125C maximum junction temperature and a thermal resistance of 88C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The dissipation is the total of all four amplifiers -- use external resistors, where possible, to allow the amplifier to saturate of to reduce the power which is dissipated in the integrated circuit. Note 5: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. Note 6: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than -0.3V (at 25C). Note 7: The LM2902EP specifications are limited to -40C TA +85C. Note 8: "Testing and other quality control techniques are used to the extent deemed necessary to ensure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific PARAMETRIC testing, product performance is assured by characterization and/or design." Note 9: VO . 1.4V, RS = 0 with V+ from 5V to 26V; and over the full input common-mode range (0V to V+ - 1.5V) Note 10: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. Note 11: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25C). The upper end of the common-mode voltage range is V+ - 1.5V (at 25C), but either or both inputs can go to +26V without damage, independent of the magnitude of V+. Note 12: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. Note 13: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 14: Human body model, 1.5 k in series with 100 pF. Note 15: The LM124 within this data sheet's graphics is referenced because of it's a similarity to the LM2902, however is not offered in this data sheet. www.national.com 4 LM2902EP Typical Performance Characteristics Input Voltage Range Input Current 20114034 20114035 Supply Current Voltage Gain 20114036 20114037 Open Loop Frequency Response Common Mode Rejection Ratio 20114038 20114039 5 www.national.com LM2902EP Typical Performance Characteristics (Continued) Voltage Follower Pulse Response Voltage Follower Pulse Response (Small Signal) 20114041 20114040 Large Signal Frequency Response Output Characteristics Current Sourcing 20114042 20114043 Output Characteristics Current Sinking Current Limiting 20114044 www.national.com 20114045 6 LM2902EP Typical Performance Characteristics (Continued) Input Current Voltage Gain 20114046 20114047 Where the load is directly coupled, as in dc applications, there is no crossover distortion. Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values of 50 pF can be accommodated using the worst-case noninverting unity gain connection. Large closed loop gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier. The bias network of the LM2902EP establishes a drain current which is independent of the magnitude of the power supply voltage over the range of from 3 VDC to 26 VDC. Output short circuits either to ground or to the positive power supply should be of short time duration. Units can be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase in IC chip dissipation which will cause eventual failure due to excessive junction temperatures. Putting direct short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the amplifiers. The larger value of output source current which is available at 25C provides a larger output current capability at elevated temperatures (see typical performance characteristics) than a standard IC op amp. The circuits presented in the section on typical applications emphasize operation on only a single power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this value in single power supply systems. Many application circuits are shown which take advantage of the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required and input voltages which range to ground can easily be accommodated. Application Hints The LM2902EP is an op amp which operates with only a single power supply voltage, has true-differential inputs, and remains in the linear mode with an input common-mode voltage of 0 VDC. This amplifier operates over a wide range of power supply voltages with little change in performance characteristics. At 25C amplifier operation is possible down to a minimum supply voltage of 2.3 VDC. The pinouts of the package have been designed to simplify PC board layouts. Inverting inputs are adjacent to outputs for all of the amplifiers and the outputs have also been placed at the corners of the package (pins 1, 7, 8, and 14). Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. Large differential input voltages can be easily accommodated and, as input differential voltage protection diodes are not needed, no large input currents result from large differential input voltages. The differential input voltage may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages from going negative more than -0.3 VDC (at 25C). An input clamp diode with a resistor to the IC input terminal can be used. To reduce the power supply drain, the amplifier has a class A output stage for small signal levels which converts to class B in a large signal mode. This allows the amplifier to both source and sink large output currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power capability of the basic amplifier. The output voltage needs to raise approximately 1 diode drop above ground to bias the on-chip vertical PNP transistor for output current sinking applications. For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover distortion. 7 www.national.com LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) Non-Inverting DC Gain (0V Input = 0V Output) 20114005 *R not needed due to temperature independent IIN DC Summing Amplifier (VIN'S 0 VDC and VO VDC) Power Amplifier 20114007 20114006 V0 = 0 VDC for VIN = 0 VDC Where: V0 = V1 + V2 - V3 - V4 AV = 10 (V1 + V2) (V3 + V4) to keep VO > 0 VDC www.national.com 8 LED Driver LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) "BI-QUAD" RC Active Bandpass Filter 20114008 20114009 fo = 1 kHz Q = 50 AV = 100 (40 dB) Fixed Current Sources Lamp Driver 20114011 20114010 9 www.national.com LM2902EP Typical Single-Supply Applications Pulse Generator (V+ = 5.0 VDC) (Note 15) (Continued) Current Monitor 20114015 Squarewave Oscillator 20114012 *(Increase R1 for IL small) Driving TTL 20114016 Pulse Generator 20114013 Voltage Follower 20114014 20114017 www.national.com 10 LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) High Compliance Current Sink 20114018 IO = 1 amp/volt VIN (Increase RE for Io small) Low Drift Peak Detector 20114019 11 www.national.com LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) Comparator with Hysteresis (Continued) Ground Referencing a Differential Input Signal 20114020 20114021 VO = VR Voltage Controlled Oscillator Circuit 20114022 *Wide control voltage range: 0 VDC VC 2 (V+ -1.5 VDC) Photo Voltaic-Cell Amplifier 20114023 www.national.com 12 LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) AC Coupled Inverting Amplifier 20114024 AC Coupled Non-Inverting Amplifier 20114025 13 www.national.com LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) DC Coupled Low-Pass RC Active Filter 20114026 fO = 1 kHz Q=1 AV = 2 High Input Z, DC Differential Amplifier 20114027 www.national.com 14 LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) High Input Z Adjustable-Gain DC Instrumentation Amplifier 20114028 Using Symmetrical Amplifiers to Reduce Input Current (General Concept) Bridge Current Amplifier 20114030 20114029 15 www.national.com LM2902EP Typical Single-Supply Applications (V+ = 5.0 VDC) (Note 15) (Continued) Bandpass Active Filter 20114031 fO = 1 kHz Q = 25 www.national.com 16 LM2902EP Physical Dimensions inches (millimeters) unless otherwise noted MX S.O. Package (M) NS Package Number M14A Molded Dual-In-Line Package (N) NS Package Number N14A 17 www.national.com LM2902EP Low Power Quad Operational Amplifiers Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560