Aluminum electrolytic capacitors
Series/Type: B41042
The following products presented in this data sheet are being withdrawn.
Ordering Code Substitute Product Date of
Withdrawal Deadline Last
Orders Last Shipments
B41042A2188M000 2011-06-24 2011-09-30 2011-12-30
B41042A2228M000 2011-06-24 2011-09-30 2011-12-30
B41042A2277M000 2011-06-24 2011-09-30 2011-12-30
Ordering Code Substitute Product Date of
Withdrawal Deadline Last
Orders Last Shipments
B41042A2337M000 2011-06-24 2011-09-30 2011-12-30
B41042A3158M000 2011-06-24 2011-09-30 2011-12-30
B41042A3227M000 2011-06-24 2011-09-30 2011-12-30
B41042A3277M000 2011-06-24 2011-09-30 2011-12-30
B41042A0127M000 2011-06-24 2011-09-30 2011-12-30
B41042A0157M000 2011-06-24 2011-09-30 2011-12-30
B41042A0226M000 2011-06-24 2011-09-30 2011-12-30
B41042A0226M008 2011-06-24 2011-09-30 2011-12-30
B41042A0276M000 2011-06-24 2011-09-30 2011-12-30
B41042A3277M007 2011-06-24 2011-09-30 2011-12-30
B41042A6277M000 2011-06-24 2011-09-30 2011-12-30
B41042A6337M000 2011-06-24 2011-09-30 2011-12-30
B41042A5107M000 2011-06-24 2011-09-30 2011-12-30
B41042A5127M000 2011-06-24 2011-09-30 2011-12-30
B41042A6476M000 2011-06-24 2011-09-30 2011-12-30
B41042A6566M000 2011-06-24 2011-09-30 2011-12-30
B41042A4108M000 2011-06-24 2011-09-30 2011-12-30
B41042A4157M000 2011-06-24 2011-09-30 2011-12-30
B41042A4187M000 2011-06-24 2011-09-30 2011-12-30
B41042A8336M000 2011-06-24 2011-09-30 2011-12-30
B41042A8396M000 2011-06-24 2011-09-30 2011-12-30
B41042A5687M000 2011-06-24 2011-09-30 2011-12-30
B41042A7477M000 2011-06-24 2011-09-30 2011-12-30
B41042A7686M000 2011-06-24 2011-09-30 2011-12-30
B41042A7826M000 2011-06-24 2011-09-30 2011-12-30
B41042A8187M000 2011-06-24 2011-09-30 2011-12-30
For further information please contact your nearest EPCOS sales office, which will also support
you in selecting a suitable substitute. The addresses of our worldwide sales network are
presented at www.epcos.com/sales.
Single-ended capacitors B41042
Low impedance – 105 °C
208/08
Please read Cautions and warnings and
Important notes at the end of this document.
Long-life grade capacitors
Applications
■Professional switch mode power supplies
Features
■RoHS-compatible
■High C/V value
■Low impedance at high frequencies
■Load life of 5000 h at 105 °C
Construction
■Radial leads
■Aluminum case, fully insulated
■Charge-discharge proof
■Minus pole marking on the insulating sleeve
■Case with safety vent from diameter 8 mm
Delivery mode
■Bulk
■Taped, Ammo pack
■Cut
■Kinked
Single-ended capacitors B41042
Low impedance – 105 °C
Single-ended capacitors B41042
Low impedance – 105 °C
308/08
Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR6.3 ... 80 V DC
Operating temp. range –55 °C … +105 °C
Rated capacitance CR
(20 °C, 120 Hz)
0.47 … 15000 µF
Capacitance tolerance ±20% M
Load life
(105 °C, VR, IAC,R)
2000 h for d = 5 ... 6.3 mm
3000 h for d = 8 mm
5000 h for d ≥ 10 mm
Requirements:
∆C/C ≤ ±25% of initial value
tan δ≤ 2 times initial specified limit
Ileak ≤ initial specified limit
Leakage current Ileak
(20 °C, after 1 minute)
Dissipation factor (max.)
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR (V DC) 6.3 10 16 25 35 506380
tan δ0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
Low temperature stability
(impedance ratio)
(120 Hz)
VR (V DC) 6.3 … 10 16 … 35 50 … 80
43 2
Shelf life After storage for 1000 h at 105 °C, the capacitors shall meet the require-
ment of load life test after reforming process. After test: VR to be applied
for 30 minutes, 24 to 48 hours before measurement.
Frequency multiplier for
rated ripple current
50 Hz 120 Hz 500 Hz 1 kHz 10 kHz 100 kHz
0.47 … 27 µF 0.40 0.55 0.65 0.80 0.90 1.00
33 … 330 µF 0.60 0.70 0.80 0.90 0.95 1.00
390 … 1000 µF 0.65 0.80 0.85 0.98 1.00 1.00
1200 µF 0.80 0.90 0.95 0.98 1.00 1.00
Temperature multiplier
for rated ripple current
+70 °C +85 °C +105 °C
1.96 1.68 1.00
Ileak 0.03 µA CR
µF
------- VR
V
-------
⋅
⎝⎠
⎛⎞
or 4 µA⋅≤
Z55 °C–()
Z+20 °C()
---------------------------
Single-ended capacitors B41042
Low impedance – 105 °C
408/08
Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing
Safety vent for diameter ≥ 8 mm.
Case dimensions
d × l
mm
dmax × Imax
mm
a
mm
b
mm
5× 11 5.5 × 12.5 2.0 ±0.5 0.5 ±0.1
6.3 × 11 6.8 × 12.5 2.5 ±0.5 0.5 ±0.1
8× 11.5 8.5 × 13.0 3.5 ±0.5 0.6 ±0.1
10 × 12.5 11.0 × 14.0 5.0 ±0.5 0.6 ±0.1
10 × 16 11.0 × 17.5 5.0 ±0.5 0.6 ±0.1
10 × 20 11.0 × 21.5 5.0 ±0.5 0.6 ±0.1
12.5 × 20 13.5 × 22.0 5.0 ±0.5 0.6 ±0.1
12.5 × 25 13.5 × 27.0 5.0 ±0.5 0.6 ±0.1
12.5 × 31.5 13.5 × 33.5 5.0 ±0.5 0.6 ±0.1
12.5 × 35.5 13.5 × 37.5 5.0 ±0.5 0.6 ±0.1
12.5 × 40 13.5 × 42.0 5.0 ±0.5 0.6 ±0.1
16 × 25 17.0 × 27.0 7.5 ±0.5 0.8 ±0.1
16 × 31.5 17.0 × 33.5 7.5 ±0.5 0.8 ±0.1
16 × 35.5 17.0 × 37.5 7.5 ±0.5 0.8 ±0.1
16 × 40 17.0 × 42.0 7.5 ±0.5 0.8 ±0.1
18 × 35.5 19.0 × 37.5 7.5 ±0.5 0.8 ±0.1
18 × 40 19.0 × 42.0 7.5 ±0.5 0.8 ±0.1
KAL1080-C-E
a
d
marking
15 min. 5 min.
-
+
øb
Minus pole Safety vent
l
Single-ended capacitors B41042
Low impedance – 105 °C
508/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR (V DC) 6.3101625
Case dimensions d × l (mm)
CR (µF)
33 5× 11
39 5× 11
47 5 × 11 6.3 × 11
56 5 × 11 6.3 × 11
68 5 × 11 6.3 × 11 6.3 × 11
82 5 × 11 6.3 × 11 6.3 × 11
100 5 × 11 6.3 × 11 6.3 × 11 6.3 × 15
120 5 × 11 6.3 × 11 6.3 × 11 6.3 × 15
150 6.3 × 11 6.3 × 11 6.3 × 15 8 × 11.5
180 6.3 × 11 6.3 × 11 6.3 × 15 10 × 12.5
220 6.3 × 11 6.3 × 15 8 × 11.5 10 × 12.5
270 6.3 × 15 6.3 × 15 10 × 12.5 10 × 16
330 6.3 × 15 8 × 11.5 10 × 12.5 10 × 16
390 8 × 11.5 10 × 12.5 10 × 16 10 × 20
470 10 × 12.5 10 × 12.5 10 × 16 10 × 20
560 10 × 12.5 10 × 16 10 × 20 10 × 25
680 10 × 16 10 × 16 10 × 20 10 × 31.5
820 10 × 16 10 × 20 10 × 25 12.5 × 20
1000 10 × 20 10 × 20 10 × 31.5 12.5 × 25
1200 10 × 20 10 × 25 12.5 × 20 12.5 × 25
1500 10 × 25 10 × 31.5 12.5 × 25 12.5 × 31.5
1800 10 × 31.5 12.5 × 20 12.5 × 31.5 12.5 × 35.5
2200 10 × 31.5 12.5 × 25 12.5 × 31.5 12.5 × 40
2700 12.5 × 25 12.5 × 31.5 12.5 × 35.5 16 × 31.5
3300 12.5 × 25 12.5 × 35.5 12.5 × 40 16 × 35.5
3900 12.5 × 31.5 12.5 × 40 16 × 31.5 16 × 40
4700 12.5 × 35.5 16 × 31.5 16 × 35.5 18 × 40
5600 12.5 × 40 16 × 35.5 16 × 40
6800 16 × 31.5 16 × 35.5 18 × 35.5
8200 16 × 35.5 16 × 40 18 × 40
10000 16 × 40 18 × 40
12000 18 × 35.5
15000 18 × 40
Single-ended capacitors B41042
Low impedance – 105 °C
608/08
Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR (V DC) 35 50 63 80
Case dimensions d × l (mm)
CR (µF)
0.47 5 × 11
0.68 5 × 11
1.0 5 × 11
1.5 5 × 11
2.2 5 × 11
3.3 5 × 11
4.7 5 × 11 5 × 11
6.8 5 × 11 5 × 11
10 5 × 11 5 × 11 6.3 × 11
12 5 × 11 5 × 11 6.3 × 11
15 5 × 11 6.3 × 11 6.3 × 11
18 5 × 11 6.3 × 11 6.3 × 11
22 5 × 11 6.3 × 11 6.3 × 11 6.3 × 15
27 5 × 11 6.3 × 11 6.3 × 11 6.3 × 15
33 6.3 × 11 6.3 × 11 6.3 × 15 8 × 11.5
39 6.3 × 11 6.3 × 11 6.3 × 15 10 × 12.5
47 6.3 × 11 6.3 × 15 8 × 11.5 10 × 12.5
56 6.3 × 11 6.3 × 15 10 × 12.5 10 × 16
68 6.3 × 15 8 × 11.5 10 × 12.5 10 × 20
82 6.3 × 15 10 × 12.5 10 × 16 10 × 20
100 8 × 11.5 10 × 16 10 × 20 10 × 25
120 10 × 12.5 10 × 16 10 × 20 10 × 31.5
150 10 × 12.5 10 × 20 10 × 25 10 × 31.5
180 10 × 16 10 × 20 10 × 31.5 12.5 × 25
220 10 × 16 10 × 25 12.5 × 20 12.5 × 31.5
270 10 × 20 10 × 31.5 12.5 × 25 12.5 × 31.5
330 10 × 20 10 × 31.5 12.5 × 25 12.5 × 35.5
390 10 × 25 12.5 × 25 12.5 × 31.5 12.5 × 40
470 10 × 31.5 12.5 × 25 12.5 × 35.5 16 × 31.5
560 12.5 × 20 12.5 × 31.5 12.5 × 40 16 × 35.5
680 12.5 × 25 12.5 × 35.5 16 × 31.5 16 × 40
820 12.5 × 25 12.5 × 40 16 × 35.5 18 × 35.5
1000 12.5 × 31.5 16 × 31.5 16 × 40 18 × 40
1200 12.5 × 35.5 16 × 35.5 18 × 40
Single-ended capacitors B41042
Low impedance – 105 °C
708/08
Please read Cautions and warnings and
Important notes at the end of this document.
1500 12.5 × 40 16 × 40
1800 16 × 31.5 18 × 35.5
2200 16 × 35.5 18 × 40
2700 16 × 40
3300 18 × 40
Overview of available types
VR (V DC) 35 50 63 80
Case dimensions d × l (mm)
CR (µF)
Single-ended capacitors B41042
Low impedance – 105 °C
808/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering codes
(composition see
below)
6.3 100 5 × 11 1.200 152 B41042A2107M***
120 5 × 11 1.100 176 B41042A2127M***
150 6.3 × 11 1.000 227 B41042A2157M***
180 6.3 × 11 0.900 253 B41042A2187M***
220 6.3 × 11 0.870 287 B41042A2227M***
270 6.3 × 15 0.700 374 B41042A2277M***
330 6.3 × 15 0.580 400 B41042A2337M***
390 8 × 11.5 0.480 448 B41042A2397M***
470 10 × 12.5 0.390 551 B41042A2477M***
560 10 × 12.5 0.350 597 B41042A2567M***
680 10 × 16 0.300 731 B41042A2687M***
820 10 × 16 0.270 796 B41042A2827M***
1000 10 × 20 0.230 953 B41042A2108M***
1200 10 × 20 0.200 1022 B41042A2128M***
1500 10 × 25 0.160 1221 B41042A2158M***
1800 10 × 31.5 0.120 1375 B41042A2188M***
2200 10 × 31.5 0.095 1472 B41042A2228M***
2700 12.5 × 25 0.092 1592 B41042A2278M***
3300 12.5 × 25 0.090 1711 B41042A2338M***
3900 12.5 × 31.5 0.080 1914 B41042A2398M***
4700 12.5 × 35.5 0.061 2102 B41042A2478M***
5600 12.5 × 40 0.059 2373 B41042A2568M***
6800 16 × 31.5 0.056 2376 B41042A2688M***
8200 16 × 35.5 0.050 2551 B41042A2828M***
10000 16 × 40 0.045 2753 B41042A2109M***
12000 18 × 35.5 0.040 2825 B41042A2129M***
15000 18 × 40 0.036 2963 B41042A2159M***
Single-ended capacitors B41042
Low impedance – 105 °C
908/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
10 68 5 × 11 1.600 152 B41042A3686M***
82 5 × 11 1.400 176 B41042A3826M***
100 6.3 × 11 1.200 211 B41042A3107M***
120 6.3 × 11 1.000 236 B41042A3127M***
150 6.3 × 11 0.820 268 B41042A3157M***
180 6.3 × 11 0.680 291 B41042A3187M***
220 6.3 × 15 0.580 372 B41042A3227M***
270 6.3 × 15 0.520 405 B41042A3277M***
330 8 × 11.5 0.470 463 B41042A3337M***
390 10 × 12.5 0.430 552 B41042A3397M***
470 10 × 12.5 0.390 596 B41042A3477M***
560 10 × 16 0.330 733 B41042A3567M***
680 10 × 16 0.280 798 B41042A3687M***
820 10 × 20 0.230 987 B41042A3827M***
1000 10 × 20 0.180 1061 B41042A3108M***
1200 10 × 25 0.160 1282 B41042A3128M***
1500 10 × 31.5 0.120 1443 B41042A3158M***
1800 12.5 × 20 0.100 1472 B41042A3188M***
2200 12.5 × 25 0.090 1715 B41042A3228M***
2700 12.5 × 31.5 0.080 1941 B41042A3278M***
3300 12.5 × 35.5 0.068 2184 B41042A3338M***
3900 12.5 × 40 0.063 2362 B41042A3398M***
4700 16 × 31.5 0.056 2422 B41042A3478M***
5600 16 × 35.5 0.050 2613 B41042A3568M***
6800 16 × 35.5 0.045 2682 B41042A3688M***
8200 16 × 40 0.041 2812 B41042A3828M***
10000 18 × 40 0.360 3045 B41042A3109M***
Single-ended capacitors B41042
Low impedance – 105 °C
10 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
16 47 5 × 11 1.200 155 B41042A4476M***
56 5 × 11 1.000 176 B41042A4566M***
68 6.3 × 11 0.900 221 B41042A4686M***
82 6.3 × 11 0.780 243 B41042A4826M***
100 6.3 × 11 0.580 267 B41042A4107M***
120 6.3 × 11 0.550 292 B41042A4127M***
150 6.3 × 15 0.520 376 B41042A4157M***
180 6.3 × 15 0.500 408 B41042A4187M***
220 8 × 11.5 0.470 462 B41042A4227M***
270 10 × 12.5 0.420 553 B41042A4277M***
330 10 × 12.5 0.390 597 B41042A4337M***
390 10 × 16 0.310 731 B41042A4397M***
470 10 × 16 0.230 772 B41042A4477M***
560 10 × 20 0.210 954 B41042A4567M***
680 10 × 20 0.180 1021 B41042A4687M***
820 10 × 25 0.150 1225 B41042A4827M***
1000 10 × 31.5 0.120 1411 B41042A4108M***
1200 12.5 × 20 0.100 1432 B41042A4128M***
1500 12.5 × 25 0.082 1665 B41042A4158M***
1800 12.5 × 31.5 0.075 1881 B41042A4188M***
2200 12.5 × 31.5 0.068 2015 B41042A4228M***
2700 12.5 × 35.5 0.062 2223 B41042A4278M***
3300 12.5 × 40 0.056 1412 B41042A4338M***
3900 16 × 31.5 0.050 2471 B41042A4398M***
4700 16 × 35.5 0.045 2585 B41042A4478M***
5600 16 × 40 0.041 2822 B41042A4568M***
6800 18 × 35.5 0.036 2903 B41042A4688M***
8200 18 × 40 0.035 3041 B41042A4828M***
Single-ended capacitors B41042
Low impedance – 105 °C
11 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
25 33 5 × 11 1.500 156 B41042A5336M***
39 5 × 11 1.300 173 B41042A5396M***
47 6.3 × 11 1.200 212 B41042A5476M***
56 6.3 × 11 1.000 237 B41042A5566M***
68 6.3 × 11 0.830 261 B41042A5686M***
82 6.3 × 11 0.750 228 B41042A5826M***
100 6.3 × 15 0.580 372 B41042A5107M***
120 6.3 × 15 0.500 409 B41042A5127M***
150 8 × 11.5 0.430 461 B41042A5157M***
180 10 × 12.5 0.400 553 B41042A5187M***
220 10 × 12.5 0.390 628 B41042A5227M***
270 10 × 16 0.300 753 B41042A5277M***
330 10 × 16 0.230 798 B41042A5337M***
390 10 × 20 0.200 986 B41042A5397M***
470 10 × 20 0.180 1021 B41042A5477M***
560 10 × 25 0.160 1223 B41042A5567M***
680 10 × 31.5 0.130 1424 B41042A5687M***
820 12.5 × 20 0.110 1433 B41042A5827M***
1000 12.5 × 25 0.090 1661 B41042A5108M***
1200 12.5 × 25 0.080 1765 B41042A5128M***
1500 12.5 × 31.5 0.072 1982 B41042A5158M***
1800 12.5 × 35.5 0.062 2080 B41042A5188M***
2200 12.5 × 40 0.056 2361 B41042A5228M***
2700 16 × 31.5 0.050 2471 B41042A5278M***
3300 16 × 35.5 0.045 2662 B41042A5338M***
3900 16 × 40 0.040 2821 B41042A5398M***
4700 18 × 40 0.036 2965 B41042A5478M***
Single-ended capacitors B41042
Low impedance – 105 °C
12 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
35 22 5 × 11 1.500 161 B41042A7226M***
27 5 × 11 1.300 182 B41042A7276M***
33 6.3 × 11 1.200 227 B41042A7336M***
39 6.3 × 11 0.830 246 B41042A7396M***
47 6.3 × 11 0.720 271 B41042A7476M***
56 6.3 × 11 0.520 298 B41042A7566M***
68 6.3 × 15 0.470 372 B41042A7686M***
82 6.3 × 15 0.420 418 B41042A7826M***
100 8 × 11.5 0.390 463 B41042A7107M***
120 10 × 12.5 0.340 551 B41042A7127M***
150 10 × 12.5 0.300 599 B41042A7157M***
180 10 × 16 0.260 731 B41042A7187M***
220 10 × 16 0.230 796 B41042A7227M***
270 10 × 20 0.210 986 B41042A7277M***
330 10 × 20 0.180 1061 B41042A7337M***
390 10 × 25 0.150 1222 B41042A7397M***
470 10 × 31.5 0.120 1423 B41042A7477M***
560 12.5 × 20 0.100 1431 B41042A7567M***
680 12.5 × 25 0.085 1663 B41042A7687M***
820 12.5 × 25 0.075 1765 B41042A7827M***
1000 12.5 × 31.5 0.068 1982 B41042A7108M***
1200 12.5 × 35.5 0.062 2184 B41042A7128M***
1500 12.5 × 40 0.056 2362 B41042A7158M***
1800 16 × 31.5 0.050 2475 B41042A7188M***
2200 16 × 35.5 0.045 2684 B41042A7228M***
2700 16 × 40 0.040 2903 B41042A7278M***
3300 18 × 40 0.036 3041 B41042A7338M***
Single-ended capacitors B41042
Low impedance – 105 °C
13 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
50 0.47 5 × 11 7.000 23 B41042A6474M***
0.68 5 × 11 6.000 29 B41042A6684M***
1.0 5 × 11 4.900 37 B41042A6105M***
1.5 5 × 11 4.600 47 B41042A6155M***
2.2 5 × 11 4.200 57 B41042A6225M***
3.3 5 × 11 3.900 68 B41042A6335M***
4.7 5 × 11 3.600 82 B41042A6475M***
6.8 5 × 11 3.200 93 B41042A6685M***
10 5 × 11 2.700 116 B41042A6106M***
12 5 × 11 2.500 127 B41042A6126M***
15 5 × 11 2.300 148 B41042A6156M***
18 5 × 11 2.100 157 B41042A6186M***
22 6.3 × 11 1.900 196 B41042A6226M***
27 6.3 × 11 1.500 216 B41042A6276M***
33 6.3 × 11 1.100 241 B41042A6336M***
39 6.3 × 11 1.000 263 B41042A6396M***
47 6.3 × 15 0.900 332 B41042A6476M***
56 6.3 × 15 0.800 361 B41042A6566M***
68 8 × 11.5 0.700 415 B41042A6686M***
82 10 × 12.5 0.600 501 B41042A6826M***
100 10 × 16 0.500 623 B41042A6107M***
120 10 × 16 0.420 675 B41042A6127M***
150 10 × 20 0.350 821 B41042A6157M***
180 10 × 20 0.310 893 B41042A6187M***
220 10 × 25 0.270 1045 B41042A6227M***
270 10 × 31.5 0.220 1203 B41042A6277M***
330 10 × 31.5 0.180 1305 B41042A6337M***
390 12.5 × 25 0.150 1441 B41042A6397M***
470 12.5 × 25 0.120 1506 B41042A6477M***
560 12.5 × 31.5 0.110 1682 B41042A6567M***
680 12.5 × 35.5 0.094 1853 B41042A6687M***
Single-ended capacitors B41042
Low impedance – 105 °C
14 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
50 820 12.5 × 40 0.088 2017 B41042A6827M***
1000 16 × 31.5 0.076 2123 B41042A6108M***
1200 16 × 35.5 0.072 2264 B41042A6128M***
1500 16 × 40 0.065 2411 B41042A6158M***
1800 18 × 35.5 0.058 2463 B41042A6188M***
2200 18 × 40 0.050 2562 B41042A6228M***
63 10 5 × 11 3.600 136 B41042A8106M***
12 5 × 11 3.200 147 B41042A8126M***
15 6.3 × 11 2.800 185 B41042A8156M***
18 6.3 × 11 2.400 199 B41042A8186M***
22 6.3 × 11 2.100 217 B41042A8226M***
27 6.3 × 11 1.900 242 B41042A8276M***
33 6.3 × 15 1.700 306 B41042A8336M***
39 6.3 × 15 1.500 332 B41042A8396M***
47 8 × 11.5 1.200 367 B41042A8476M***
56 10 × 12.5 1.100 451 B41042A8566M***
68 10 × 12.5 0.900 503 B41042A8686M***
82 10 × 16 0.800 605 B41042A8826M***
100 10 × 20 0.650 751 B41042A8107M***
120 10 × 20 0.580 823 B41042A8127M***
150 10 × 25 0.520 954 B41042A8157M***
180 10 × 31.5 0.420 1113 B41042A8187M***
220 12.5 × 20 0.320 1142 B41042A8227M***
270 12.5 × 25 0.280 1345 B41042A8277M***
330 12.5 × 25 0.220 1421 B41042A8337M***
390 12.5 × 31.5 0.190 1623 B41042A8397M***
470 12.5 × 35.5 0.160 1785 B41042A8477M***
560 12.5 × 40 0.140 1952 B41042A8567M***
680 16 × 31.5 0.120 2053 B41042A8687M***
820 16 × 35.5 0.110 2223 B41042A8827M***
1000 16 × 40 0.098 2374 B41042A8108M***
1200 18 × 40 0.088 2511 B41042A8128M***
Single-ended capacitors B41042
Low impedance – 105 °C
15 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
016 = for taped leads, Ammo pack, lead spacing a = 2.0 mm
007 = for taped leads, Ammo pack, lead spacing a = 2.5 mm
006 = for taped leads, Ammo pack, lead spacing a = 3.5 mm
008 = for taped leads, Ammo pack, lead spacing a = 5.0 mm
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
Case
dimensions
d × l
mm
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
80 4.7 5 × 11 8.500 92 B41042A0475M***
6.8 5 × 11 5.500 111 B41042A0685M***
10 6.3 × 11 3.800 152 B41042A0106M***
12 6.3 × 11 3.400 164 B41042A0126M***
15 6.3 × 11 3.000 189 B41042A0156M***
18 6.3 × 11 2.600 205 B41042A0186M***
22 6.3 × 15 2.200 226 B41042A0226M***
27 6.3 × 15 2.000 256 B41042A0276M***
33 8 × 11.5 1.800 307 B41042A0336M***
39 10 × 12.5 1.600 381 B41042A0396M***
47 10 × 12.5 1.300 410 B41042A0476M***
56 10 × 16 1.200 510 B41042A0566M***
68 10 × 20 1.000 636 B41042A0686M***
82 10 × 20 0.850 676 B41042A0826M***
100 10 × 25 0.700 839 B41042A0107M***
120 10 × 31.5 0.620 1032 B41042A0127M***
150 10 × 31.5 0.550 1070 B41042A0157M***
180 12.5 × 25 0.450 1115 B41042A0187M***
220 12.5 × 31.5 0.350 1433 B41042A0227M***
270 12.5 × 31.5 0.300 1509 B41042A0277M***
330 12.5 × 35.5 0.240 1693 B41042A0337M***
390 12.5 × 40 0.200 1828 B41042A0397M***
470 16 × 31.5 0.170 1902 B41042A0477M***
560 16 × 35.5 0.150 2080 B41042A0567M***
680 16 × 40 0.130 2313 B41042A0687M***
820 18 × 35.5 0.120 2357 B41042A0827M***
1000 18 × 40 0.100 2518 B41042A0108M***
Single-ended capacitors B41042
Taping, packing and lead configurations
16 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations of single-ended capacitors
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 10 mm as follows:
Lead spacing 2.0 mm (∅ d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
Dimensions in mm
∅ dF H W W
0W1W2PP
0P1l1t∆hD
0
4 ... 5 2.0 18.5 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
–0.2 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1138-D-E
1 max.
View B
P
0
0
H
P
1
D
0
W0W2
W1
1
l
h∆h∆
Single-ended capacitors B41042
Taping, packing and lead configurations
Single-ended capacitors B41042
Taping, packing and lead configurations
17 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 2.5 mm (∅ d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅ dFHH
0WW
0W1W2PP
0P1l1t∆hD
0
4 ... 6.3 2.5 18.5 16.0 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 0 4.0
To le r an ce – 0 . 2 ±0.75 ±0.5 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
Dimensions in mm
∅ dFHWW
0W1W2PP
0P1l1t∆hD
0
8 3.5 18.5 18.0 10 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
Tole ra n ce ±0.5 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 max. ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1074-3-E
1 max.
View B
P0
0
H
P1
D0
W
0
W
2
W
1
1
l
h∆h∆
Adhesive tape
Base tape F
B
H
ød
P
W
t
KAL1138-D-E
1 max.
View B
P
0
0
H
P
1
D
0
W0W2
W1
1
l
h∆h∆
Single-ended capacitors B41042
Taping, packing and lead configurations
18 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (∅ d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅ d = 10 mm)
Last 3 digits of ordering code: 008
Taping is available up to dimensions d × l = 10 × 20 mm. For ∅ 12.5, 16 and 18 mm taping is not
available.
Dimensions in mm
∅ dFHH
0WW
0W1W2PP
0P1L1t∆hD
0
4 ... 6.3 5.0 18.5 16 18.0 7.0 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
8 5.0 18.5 16 18.0 10 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
10 5.0 18.5 – 18.0 12.5 9.0 3.0 12.7 12.7 3.85 1.0 0.6 2.0 4.0
Tolerance +0.6
–0.2
±0.75 ±0.5 +1.0
–0.5
+1.0
–0
±0.5 max. ±0.5 ±0.3 ±0.7 max. +0.3
–0.2
max. ±0.2
Adhesive tape
Base tape F
B
H
ød
P
W
KAL1075-B-E
t
1 max.
View B
0
P
P1
D0
H
0
1
W
W
2
W
0
1
l
h∆h∆
Adhesive tape
Base tape F
B
H
ød
P
W
KAL1076-J-E
t
1 max.
View B
P
0
P
1
D
0
W
0
W
2
W
1
1
l
h∆h∆
Single-ended capacitors B41042
Taping, packing and lead configurations
19 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also avail-
able on request.
Kinked leads
Last 3 digits of ordering code: 001
Case size d × l (mm) a (mm) Case size d × l (mm) a (mm)
4 × 7 1.5 12.5 × 16 5.0
5 × 7 2.0 12.5 × 20 5.0
5 × 11 2.0 12.5 × 25 5.0
6.3 × 7 2.5 12.5 × 31.5 5.0
6.3 × 11 2.5 12.5 × 35.5 5.0
6.3 × 15 2.5 12.5 × 40 5.0
8 × 7 3.5 16 × 20 7.5
8 × 11.5 3.5 16 × 25 7.5
8 × 15 3.5 16 × 31.5 7.5
8 × 20 3.5 16 × 35.5 7.5
10 × 12.5 5.0 16 × 40 7.5
10 × 16 5.0 18 × 20 7.5
10 × 20 5.0 18 × 25 7.5
10 × 25 5.0 18 × 31.5 7.5
10 × 31.5 5.0 18 × 35.5 7.5
18 × 40 7.5
ød
3.2±0.1
KAL1137-5
1.2±0.1
2.1±0.1
l
4.5±0.5
ød
KAL1084-A
a
l
Single-ended capacitors B41042
Taping, packing and lead configurations
20 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads
Last 3 digits of ordering code: 002
Case size d × l (mm) a (mm) Case size d × l (mm) a (mm)
4 × 7 1.5 12.5 × 16 5.0
5 × 7 2.0 12.5 × 20 5.0
5 × 11 2.0 12.5 × 25 5.0
6.3 × 7 2.5 12.5 × 31.5 5.0
6.3 × 11 2.5 12.5 × 35.5 5.0
6.3 × 15 2.5 12.5 × 40 5.0
8 × 7 3.5 16 × 20 7.5
8 × 11.5 3.5 16 × 25 7.5
8 × 15 3.5 16 × 31.5 7.5
8 × 20 5.0 16 × 35.5 7.5
10 × 12.5 5.0 16 × 40 7.5
10 × 16 5.0 18 × 20 7.5
10 × 20 5.0 18 × 25 7.5
10 × 25 5.0 18 × 31.5 7.5
10 × 31.5 5.0 18 × 35.5 7.5
18 × 40 7.5
ød
KAL1086-R
a
4.5±0.5
l
21 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
General
Also see “Important notes” on page 23.
1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2 The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv-
ice life.
3 The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not ex-
ceed the rated DC voltage.
4 Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5 Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6 Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7 Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8 The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example un-
der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9 The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10 Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Cautions and warnings
Cautions and warnings
22 08/08
Please read Cautions and warnings and
Important notes at the end of this document.
11 Do not apply excessive force to the leads and terminals. Do not move the capacitor after sol-
dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12 The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13 The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Important notes
23 08/08
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
