Data Sheet PS9123 R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 HIGH CMR, 15 Mbps TOTEM POLE OUTPUT TYPE, 5-PIN SOP (SO-5) PHOTOCOUPLER DESCRIPTION The PS9123 is an optically coupled high-speed, totem pole output isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9123 is specified high CMR, high CTR and pulse width distortion with operating temperature. <R> FEATURES * * * * * * * * * High common mode transient immunity (CMH, CML = 20 kV/s TYP.) Small package (SO-5) Pulse width distortion (tPHL - tPLH = 4 ns TYP.) High-speed (15 Mbps) High isolation voltage (BV = 3 750 Vr.m.s.) Totem pole output Embossed tape product : PS9123-F3 : 2 500 pcs/reel Pb-Free product Safety standards * UL approved: File No. E72422 * CSA approved: No. CA 101391 (CA5A, CAN/CSA-C22.2 60065, 60950) * DIN EN60747-5-5 (VDE0884-5): 2011-11 approved No. 40008902 (Option) PIN CONNECTION (Top View) 5 4 1. Anode 2. Cathode 3. GND 4. VO 5. VCC 1 2 TRUTH TABLE LED ON OFF APPLICATIONS * PLC * Inverter * AC servo 3 Output L H The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 1 of 13 PS9123 e <R> PACKAGE DIMENSIONS (UNIT: mm) 3.4 5 +0.3 -0.1 4 3 7.00.3 *1 (4.4) 2 0.10.1 2.60.2 0.15 +0.10 -0.05 1 0.50.3 1.27 0.4 +0.10 -0.05 0.25 M *1 ( ) indicates reference dimension. <R> PHOTOCOUPLER CONSTRUCTION Parameter Air Distance Outer Creepage Distance Isolation Distance <R> Unit (MIN.) 4.2 mm 4.2 mm 0.2 mm MARKING EXAMPLE Ni/Pd/Au PLATING 9123 N231 No. 1 pin Mark Initial of Renesas (Engraved mark) Type Number Assembly Lot *1 R N 2 31 Week Assembled Year Assembled (Last 1 Digit) Rank Code *1 R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Bar : Pb-Free Page 2 of 13 PS9123 e <R> ORDERING INFORMATION Part Number PS9123 PS9123-F3 PS9123-AX PS9123-F3-AX PS9123-V PS9123-V-F3 PS9123-V-AX PS9123-V-F3-AX Note: <R> Order Number Packing Style Solder Plating Specification Pb-Free (Ni/Pd/Au) Safety Standard Approval 20 pcs (Tape 20 pcs cut) Standard products Embossed Tape 2 500 pcs/reel 20 pcs (Tape 20 pcs cut) (UL, CSA approved) Embossed Tape 2 500 pcs/reel Application Part *1 Number PS9123 DIN EN60747-5-5 (VDE0884-5): 2011-11 Approved (Option) 1. For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified) Diode Detector Parameter Forward Current 1 Reverse Voltage Supply Voltage Output Voltage Symbol IF VR VCC VO High Level Output Current Low Level Output Current Power Dissipation 2 Isolation Voltage *3 Operating Ambient Temperature Storage Temperature IOH Ratings 20 5 7 7 -5 Unit mA V V V mA IOL 13 mA PC BV TA Tstg 130 3 750 -40 to +100 -55 to +125 mW Vr.m.s. C C Notes: 1. Reduced to 0.19 mA/C at TA = 60C or more. 2. TA = -40 to +100C, applies to output pin VO and power supply pin VCC. Reduced to 2.4 mW/C at TA = 70C or more. 3. AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. <R> RECOMMENDED OPERATING CONDITIONS Parameter High Level Input Current Low Level Input Voltage Supply Voltage TTL (loads) R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Symbol IFH VFL VCC N MIN. 7.5 0 4.5 TYP. 5.0 MAX. 12.5 0.8 5.5 3 Unit mA V V Page 3 of 13 PS9123 e <R> ELECTRICAL CHARACTERISTICS (TA = -40 to +100C, unless otherwise specified) Diode Detector Coupled Parameter Forward Voltage Reverse Current Terminal Capacitance Symbol VF IR Ct Conditions IF = 10 mA, TA = 25C VR = 3 V, TA = 25C f = 1 MHz, VF = 0 V, TA = 25C MIN. 1.3 TYP.1 1.55 MAX. 1.8 10 30 0.05 100 Unit V A pF A High Level Output Current IOH VCC = VO = 5.5 V, IF = 0 mA High Level Output Voltage VOH VCC = 4.5 V, IF = 0 mA, IOH = -2 mA Low Level Output Voltage VOL VCC = 4.5 V, IF = 7 mA, IOL = 8 mA 0.25 0.6 V High Level Supply Current ICCH VCC = 5.5 V, IF = 0 mA, VO = open 4 7 mA Low Level Supply Current ICCL VCC = 5.5 V, IF = 10 mA, VO = open 6 10 mA High Level Output Short Circuit Current IOSH VCC = 5.5 V, VO = GND, IF = 0 mA, 10 ms or less -43 mA Low Level Output Short Circuit Current IOSL 28 mA Threshold Input Voltage (H L) Isolation Resistance IFHL VCC = VO = 5.5 V, IF = 8 mA, 10 ms or less VCC = 5 V, VO = 0.6 V RI-O Isolation Capacitance CI-O Propagation Delay Time *2 (H L) tPHL VI-O = 1 kVDC, RH = 40 to 60%, TA = 25C V = 0 V, f = 1 MHz, TA = 25C VCC = 5 V, IF = 7.5 mA Propagation Delay Time *2 (L H) tPLH VCC = 5 V, IF = 7.5 mA Pulse Width Distortion *2 (PWD) 2.4 3.0 2.3 V 5 mA 11 10 10 0.6 28 60 pF ns 10 32 60 ns 4 30 ns tPHL-tPLH VCC = 5 V, IF = 7.5 mA Common Mode Transient Immunity at *3 High Level Output CMH VCC = 5 V, TA = 25C, IF = 0 mA, VO (MIN.) = 2 V, VCM = 1 kV 15 20 kV/s Common Mode Transient Immunity at *3 Low Level Output CML VCC = 5 V, TA = 25C, IF = 7.5 mA, VO (MAX.) = 0.8 V, VCM = 1 kV 15 20 kV/s R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 4 of 13 PS9123 e Notes: *1. Typical values at TA = 25C *2. Test circuit for propagation delay time VCC = 5 V VCC = 5 V Pulse input (IF) VO (monitor) (PW = 500 ns, Duty cycle = 1/2) 1 5 4 Input (monitor) 1.3 k 0.1 F VOH 3 2 IF (ON) 50% IF (ON) Input Output CL = 30 pF 2.5 k 47 tPHL 1.5 V VOL tPLH CL includes probe and stray wiring capacitance. *3. Test circuit for common mode transient immunity 1 kV VCM 90% IF 1 VCC = 5 V 5 4 SW 10% 0.1 F VO (Monitor) 3 2 CL = 15 pF + - VCM = 1 kV 0V tr VO (IF = 0 mA) VO (IF = 7.5 mA) tf VOH 2V 0.8 V VOL CL includes probe and stray wiring capacitance. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 5 of 13 PS9123 e TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 150 Detector Power Dissipation PC (mW) Maximum Forward Current IF (mA) 40 30 20 10 0 20 40 60 80 100 120 100 50 0 20 40 Ambient Temperature TA (C) High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA) Forward Current IF (mA) 100 120 20 10 TA = +100C +85C +50C +25C 0C -40C 1 0.1 1.2 1.4 1.6 1.8 2.0 2.2 2.4 VCC = 5.5 V 16 12 ICCL (IF = 10 mA) 8 ICCH (IF = 0 mA) 4 0 -50 -25 Forward Voltage VF (V) VCC = 4.5 V, VF = 0.8 V, IOH = 2.0 mA 4.0 3.0 2.0 1.0 -25 0 25 50 25 50 75 100 PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE 75 100 Ambient Temperature TA (C) 50 Propagation Delay Time tPHL, tPLH (ns), Pulse Width Distortion tPHL - tPLH (ns) 5.0 0 Ambient Temperature TA (C) HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 0 -50 80 SUPPLY CURRENT vs. AMBIENT TEMPERATURE 100 0.01 1.0 60 Ambient Temperature TA (C) FORWARD CURRENT vs. FORWARD VOLTAGE High Level Output Voltage VOH (V) <R> IF = 7.5 mA VCC = 5.0 V 40 tPHL 30 tPLH 20 10 PWD 0 -50 -25 0 25 50 75 100 Ambient Temperature TA (C) Remark The graphs indicate nominal characteristics. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 6 of 13 PS9123 e THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 5 VCC = 4.5 V, IF = 7.5 mA, IOL = 8.0 mA 0.4 VCC = 5.0 V Threshold Input Current IFHL (mA) Low Level Output Voltage VOL (V) 0.5 0.3 0.2 0.1 0 -50 -25 0 25 50 75 3 2 1 0 -50 100 -25 50 75 100 LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT 5 High Level Output Voltage VOH (V) 0.4 TA = 100C 85C 0C 25C 0.3 0.2 0.1 2.5 0 5 7.5 10 TA = 100C 85C 25C 0C -40C 4 2 1 0 12.5 13 -1 3 VCC = 4.5 V, IF = 250 A 2 1 -5 -10 -15 -20 -25 -3 -4 -5 PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT Propagation Delay Time tPHL, tPLH (ns), Pulse Width Distortion tPHL - tPLH (ns) TA = 100C 85C 25C 0C -40C -2 High Level Output Current IOH (mA) HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT 4 VCC = 4.5 V, VF = 0.8 V 3 Low Level Output Current IOL (mA) High Level Output Voltage VOH (V) 25 Ambient Temperature TA (C) VCC = 4.5 V, IF = 5.0 mA 0 0 Ambient Temperature TA (C) 0.5 Low Level Output Voltage VOL (V) 4 -30 High Level Output Current IOH (mA) 60 TA = 25C, VCC = 5 V 40 tPHL tPLH 20 PWD 0 5 10 15 20 25 Forward Current IF (mA) Remark The graphs indicate nominal characteristics. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 7 of 13 PS9123 e TAPING SPECIFICATIONS (UNIT: mm) 1.550.1 3.90.1 8.00.1 7.40.1 1.5+0.1 -0 12.00.2 2.00.05 4.00.1 1.750.1 Outline and Dimensions (Tape) 5.50.1 3.45 MAX. 3.00.1 0.30.05 Tape Direction PS9123-F3 Outline and Dimensions (Reel) 2.00.5 2.00.5 21.00.8 1001.0 R 1.0 13.00.2 13.00.2 3302.0 <R> 13.51.0 17.51.0 Packing: 2 500 pcs/reel R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 11.9 to 15.4 Outer edge of flange Page 8 of 13 PS9123 e RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) B2 C D B1 <R> A R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Part Number A B1 B2 C D PS9123 6.25 1.27 2.54 0.8 1.45 Page 9 of 13 PS9123 e NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature 260C or below (package surface temperature) * Time of peak reflow temperature 10 seconds or less * Time of temperature higher than 220C 60 seconds or less * Time to preheat temperature from 120 to 180C 12030 s * Number of reflows Three or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% or less is recommended.) Package Surface Temperature T (C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating) Time (s) (2) Wave soldering * Temperature * Time * Preheating conditions * Number of times * Flux 260C or below (molten solder temperature) 10 seconds or less 120C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% or less is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) 350C or below * Time (each pin) 3 seconds or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% or less is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions Regarding Noise Be aware that when voltage is applied suddenly between the photocoupler's input and output at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 10 of 13 PS9123 e USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 F or more is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is 10 mm or less. 3. Avoid storage at a high temperature and high humidity. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 11 of 13 PS9123 e <R> SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Climatic test class (IEC 60068-1/DIN EN 60068-1) Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.6 x UIORM, Pd < 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 x UIORM, Pd < 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303 Part 11)) Material group (DIN EN 60664-1 VDE0110 Part 1) Storage temperature range Operating temperature range Isolation resistance, minimum value VIO = 500 V dc at TA = 25C VIO = 500 V dc at TA MAX. at least 100C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Symbol Spec. 40/100/21 Unit UIORM Upr 707 1 131 Vpeak Vpeak Upr 1 326 Vpeak UTR 6 000 2 Vpeak CTI 175 Tstg TA III a -55 to +125 -40 to +100 C C Ris MIN. Ris MIN. 1012 11 10 Tsi Isi Psi 150 200 300 C mA mW Ris MIN. 109 Page 12 of 13 PS9123 e Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. R08DS0030EJ0100 Rev.1.00 Aug 14, 2012 Page 13 of 13 Revision History PS9123 Data Sheet Rev. Date Page 0.01 1.00 Jan 29, 2011 Aug 14, 2012 - Throughout p.1 p.2 p.3 pp.4, 5 pp.6, 7 p.8 p.9 pp.10, 11 p.12 Description Summary First edition issued "Preliminary Data Sheet" is changed to "Data Sheet." Modification of FEATURES Modification of PACKAGE DIMENSIONS Modification of PHOTOCOUPLER CONSTRUCTION Modification of MARKING EXAMPLE Addition of ORDERING INFORMATION Modification of ABSOLUTE MAXIMUM RATINGS Modification of RECOMMENDED OPERATING CONDITIONS Modification of ELECTRICAL CHARACTERISTICS Addition of TYPICAL CHARACTERISTICS Addition of TAPING SPECIFICATIONS Addition of RECOMMENDED MOUNT PAD DIMENSIONS Addition of NOTES ON HANDLING Addition of SPECIFICATION OF VDE MARKS LICENSE DOCUMENT All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 (c) 2012 Renesas Electronics Corporation. All rights reserved. Colophon 2.2