CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
1
FEATURES
• Similar printed circuit board (PCB) and open frame structure for low cost
• Wide range of models (25 W to 150 W) to meet any need
• Resonant topology design for high efficiency and low noise (FCC class B)
• Proprietary SANKEN power hybrid IC STR-Z makes them small and light
• Complies with UL and CSA safety standards (pending approval)
• The low-capacity CSJ Series is also available (Ringing Choke Converter
(RCC) type design, 10 W and 15 W models)
• CSJ series meet FCC class B standard
CSH Series
CSH Series
CSJ Series
CSJ Series
SINGLE OUTPUT
10W, 15W
25W, 50W, 100W, 150W
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
2
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
3
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current Rated input/output conditions
Rated Frequency
Frequency Range
Efficiency (typ) Rated input/output conditions
Inrush Current (see Note 1) Rated input/output conditions
Rated Output Voltage
Adjustable Output Voltage Range (see Note 5-a, b)
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple Noise (mVp-p) (see Notes 2, 3) Rated input/output conditions
Constant Voltage Accuracy (see Notes 4, 5-a, b)
Leakage Current Rated input/output conditions
Startup Time Rated input/output conditions
Output Holdup Time Rated input/output conditions
Over Current Protection (see Note 7)
Over Voltage Protection (see Note 7)
Remote Sensing
Remote On/Off Control
Display
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Cooling Requirements
Vibration Resistance Vibration Frequency
Test Duration
Acceleration
Vibration Direction
Vibration Duration
Shock Resistance
Installation Conditions
Insulation Withstand Voltage Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
External Appearance
Size (dimensions in mm)
Weight
Safety Standards
EMI Standards
Input
Note 1: More current may flow at restart. (Power thermistor type)
Note 2: Ripple noise is measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point. Constant voltage accuracy is measured at
the output connector.
Note 3: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Note 4: Constant voltage accuracy is the output voltage accuracy with a static input voltage over the range of 85 to 132 V AC, with a static load over the range of 0 to 100%, time drift
of 10 minutes to 8 hours, over an ambient temperature range of -10 to 60°C.
Note 5: a) When varying the output voltage, the unit may be used in a range such that the output does not exceed the rated maximum output voltage or rated current.
b) When adjusting downwards with a light load, the output voltage may rise and exceed the constant voltage accuracy specification.
Note 6: Insulation specifications are for normal temperature and humidity.
Note 7: To reset the power supply, turn off the input power, then re-apply power after about one minute.
OutputOther
Additional
Functions
EnvironmentalInsulation
Structural
Specifications
Applicable
Standards
25W
CSH 025-05 CSH 025-12 CSH 025-15 CSH 025-24
100-120V AC
85 to 132V AC
0.6/0.5A (typ)
50/60 Hz
47 to 440 Hz
80% 83% 84% 86%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
5A 2.1A 1.7A 1.1A
0 to 100%
25W 25.2W 25.5W 26.4W
80mVp-p 100mVp-p 100mVp-p 100mVp-p
±3%
0.5mA (max)
400ms (typ)
16ms (min)
Detection above 105% of rated current (output cutoff)
Detection above 115% of rated voltage (output cutoff)
Not provided
Not provided
Not provided
-10 to +60°C (70% load at -10°C, 60°C)
-25 to +85°C
30 to 90% (no condensation)
30 to 90% (no condensation)
Natural air cooling
10 to 55 Hz
3 minutes
2 G
X, Y, and Z directions
One hour in each direction
10 G
With the unit resting on a smooth-surfaced wooden plank, at least 10 mm thick, each side of the unit is
raised 50 mm and allowed to fall freely. This is performed three times for each of the four sides.
Derating is necessary depending on the installation conditions. Refer to (1) below.
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
Open frame
115 x 50 (or less) x 23 (W x D x H)
about 85 g
Designed to meet UL 1950 / Designed to meet CSA C22.2 No. 234 Level 3 /
Designed to comply with the Electrical Appliance and Materials Control Law
Designed to meet FCC Class B (100 to 120 V AC) / Designed to meet VCCI Class 2
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
4
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current (see Note 8) Rated input/output conditions
Rated Frequency
Frequency Range
Efficiency (typ) (see Note 8) Rated input/output conditions
Inrush Current (see Note 1, 8) Rated input/output conditions
Rated Output Voltage
Adjustable Output Voltage Range (see Note 5-a, b)
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple Noise (mVp-p) (
see Notes 2, 3, 8
)Rated input/output conditions
Constant Voltage Accuracy (see Notes 4, 5-a, b)
Leakage Current (see Note 8) Rated input/output conditions
Startup Time (see Note 8) Rated input/output conditions
Output Holdup Time (see Note 8) Rated input/output conditions
Over Current Protection
Over Voltage Protection
Remote Sensing
Remote On/Off Control
Display
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Cooling Requirements
Vibration Resistance Vibration Frequency
Test Duration
Acceleration
Vibration Direction
Vibration Duration
Shock Resistance
Installation Conditions
Insulation Withstand Voltage Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
External Appearance
Size (dimensions in mm)
Weight
PCB Material
Safety Standards
EMI Standards
InputOutputOther
Additional
Functions
EnvironmentalInsulation
Structural
Specifications
Applicable
Standards
50W
CSH 050-05 CSH 050-12 CSH 050-15 CSH 050-24
100-120V AC
85 to 132V AC
1A (typ)
50/60 Hz
47 to 440 Hz
81% 86% 87% 90%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
10A 4.2A 3.4A 2.1A
0 to 100%
50W 50.4W 51W 50.4W
80mVp-p 100mVp-p 100mVp-p 100mVp-p
±3%
0.3mA (max)
400ms (typ)
16ms (min)
Detection above 105% of rated current (output cutoff)
Detection above 115% of rated voltage (output cutoff)
Not provided
Not provided
Not provided
-10 to +60°C (70% load at -10°C, 60°C)
-25 to +85°C
30 to 90% (no condensation)
30 to 90% (no condensation)
Natural air cooling
10 to 55 Hz
3 minutes
2 G
X, Y, and Z directions
One hour in each direction
10 G
With the unit resting on a smooth-surfaced wooden plank, at least 10 mm thick, each side of the unit is
raised 50 mm and allowed to fall freely. This is performed three times for each of the four sides.
Derating is necessary depending on the installation conditions. Refer to (2) below.
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
Open frame
150 x 50 (or less) x 25 (W x D x H)
about 150 g
Designed to meet UL 1950 / Designed to meet CSA C22.2 No. 234 Level 3 /
Designed to comply with the Electrical Appliance and Materials Control Law
Designed to meet FCC Class B (100 to 120 V AC) / Designed to meet VCCI Class 2
Note 1: More current may flow at restart. (Power thermistor type)
Note 2: Ripple noise is measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point. Constant voltage accuracy is measured at
the output connector.
Note 3: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Note 4: Constant voltage accuracy is the output voltage accuracy with a static input voltage over the range of 85 to 132 V AC, with a static load over the range of 0 to 100%, time drift
of 10 minutes to 8 hours, over an ambient temperature range of -10 to 60°C.
Note 5: a) When varying the output voltage, the unit may be used in a range such that the output does not exceed the rated maximum output voltage or rated current.
b) When adjusting downwards with a light load, the output voltage may rise and exceed the constant voltage accuracy specification.
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
5
Note 6: Insulation specifications are for normal temperature and humidity.
Note 7: To reset the power supply, turn off the input power, then re-apply power after about one minute.
Note 8: Under standard input/output conditions at an ambient temperature of 25°C.
Note 9: Values in parentheses are with the high harmonic reactor installed.
Note 10: If shutdown occurs due to over current or over voltage conditions, remove the source of the problem and re-apply power after about one minute powered off.
*"Under rated input/output conditions"means that the switching power supply is operated under the rated input voltage, rated output current, rated frequency, and normal
temperature and humidity.
100W
CSH 100-05 CSH 100-12 CSH 100-15 CSH 100-24
100-120V AC
85 to 132V AC (see Note 9)
2.2A (typ) (see Note 8, 9)
50/60 Hz
47 to 440 Hz
82% 87% 90% 90%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10% (see Note 4, 5-a, b)
20.0A 8.5A 7.0A 4.3A
0 to 100%
100W 102W 105W 103.2W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3% (see Note 4, 5-a, b)
0.3mA (max) (see Note 8)
300ms (typ) (see Note 8)
17ms (min) (see Note 8)
Derating is necessary depending on the installation conditions. Refer to (3) below.
Open frame (PCB only)
222 x 62 x 32 (W x D x H)
about 520 g (380 g without high harmonic suppression reactor) (max)
(see Note 9)
CEM-1
150W
CSH 150-05 CSH 150-12 CSH 150-15 CSH 150-24
120V AC
85 to 132V AC (90 to 132V AC) (see Note 9)
3.5A (typ) (see Note 8)
50/60 Hz
47 to 440 Hz
78% 84% 86% 87%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10% (see Note 4)
30.0A 12.5A 10.0A 6.3A
0 to 100%
150W 150W 150W 151.2W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3% (see Note 4, 5-a, b)
0.3mA (max) (see Note 8)
600ms (typ) (see Note 8)
17ms (min) (see Note 8)
Derating is necessary depending on the installation conditions. Refer to (4) below.
Open frame (PCB only)
222 x 75 x 36 (W x D x H)
about 520 g (without high harmonic suppression reactor) (max)
CEM-1
Detection above 105% of rated current (output cutoff) (see Note 10)
Detection above 115% of rated voltage (output cutoff) (see Note 10)
Not provided
Not provided
Not provided
-10 to +60°C
-25 to +85°C
30 to 90% (no condensation)
Natural air cooling
10 to 55 Hz
3 minutes
2 G
X, Y, and Z directions
One hour in each direction
10 G With the unit resting on a smooth-surfaced wooden plank, at least 10 mm thick, each side of the unit is raised 50 mm and allowed to fall freely.
This is performed three times for each of the four sides.
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
(see Note 6)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
(see Note 6)
100 MΩ(measured with 500 V DC Megger) (see Note 6)
Designed to meet UL 1950 / Designed to meet CSA C22.2 No. 234 Level 3 /
Designed to comply with the Electrical Appliance and Materials Control Law
Designed to meet FCC Class B (100 to 120 V AC) / Designed to meet VCCI Class 2
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current (see Note 8) Rated input/output conditions
Rated Frequency
Frequency Range
Efficiency (typ) (see Note 8) Rated input/output conditions
Inrush Current (see Note 1, 8) Rated input/output conditions
Rated Output Voltage
Adjustable Output Voltage Range (see Note 5-a)
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple Noise (mVp-p) (see Notes 2, 3) Rated input/output conditions
Constant Voltage Accuracy (see Notes 4, 5-a)
Leakage Current (see Note 8) Rated input/output conditions
Startup Time (see Note 8) Rated input/output conditions
Output Holdup Time (see Note 8) Rated input/output conditions
Over Current Protection
Over Voltage Protection
Remote Sensing
Remote On/Off Control
Display
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Cooling Requirements
Vibration Resistance Vibration Frequency
Test Duration
Acceleration
Vibration Direction
Vibration Duration
Shock Resistance
Installation Conditions
Insulation Withstand Voltage Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
(see Note 6) Between Input and Frame
Between Output and Frame
External Appearance
Size (dimensions in mm)
Weight
PCB Material
Safety Standards
EMI Standards
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
6
InputOutputOther
Additional
Functions
Environmental
Insulation
Structural
Specifications
Applicable
Standards
10W
CSJ 010-05 CSJ 010-12 CSJ 010-15 CSJ 010-24
100-120V AC
85 to 132V AC
0.3A (typ)
50/60 Hz
47 to 440 Hz
72% 73% 75% 77%
30 A (max, at cold start)
+5V +12V +15V +24V
Rated voltage ±10%
2.0A 0.85A 0.7A 0.45A
0 to 100%
10.0W 10.2W 10.5W 10.8W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3%
0.3mA (max)
20ms (typ)
17ms (min)
Detection above 105% of rated current (output cutoff)
Detection above 115% of rated voltage (output cutoff)
Not provided
Not provided
Not provided
-10 to +60°C (70% load at 60°C)
-25 to +85°C
30 to 90% (no condensation)
30 to 90% (no condensation)
Natural air cooling
10 to 55 Hz
3 minutes
2 G
X, Y, and Z directions
One hour in each direction
10 G
With the unit resting on a smooth-surfaced wooden plank, at least 10 mm thick, each side of the unit is
raised 50 mm and allowed to fall freely. This is performed three times for each of the four sides.
Derating is necessary depending on the installation conditions. Refer to (5) below.
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
Open frame (PCB only)
94 x 49 x 17 (W x D x H)
about 55 g
CEM-1
Designed to meet UL 1950 / Designed to meet CSA C22.2 No. 234 Level 3 /
Designed to comply with the Electrical Appliance and Materials Control Law
Designed to meet FCC Class B (100 to 120 V AC) / Designed to meet VCCI Class 2
Note 1: More current may flow at restart. (Power thermistor type)
Note 2: Ripple noise is measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point. Constant voltage accuracy is measured at
the output connector.
Note 3: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Note 4: Constant voltage accuracy is the output voltage accuracy with a static input voltage over the range of 85 to 132 V AC, with a static load over the range of 0 to 100%, time drift
of 10 minutes to 8 hours, over an ambient temperature range of -10 to 60°C.
Note 5: a) When varying the output voltage, the unit may be used in a range such that the output does not exceed the rated maximum output voltage or rated current.
b) When adjusting downwards with a light load, the output voltage may rise and exceed the constant voltage accuracy specification.
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
7
15W
CSJ 015-05 CSJ 015-12 CSJ 015-15 CSJ 015-24
100-120V AC
85 to 132V AC
0.4A (typ)
50/60 Hz
47 to 440 Hz
72% 73% 75% 77%
30 A (max, at cold start)
+5V +12V +15V +24V
Rated voltage ±10%
3.0A 1.25A 1.0A 0.65A
0 to 100%
15.0W 15.0W 15.0W 15.6W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3%
0.3mA (max)
20ms (typ)
16ms (min)
Detection above 105% of rated current (output cutoff)
Detection above 115% of rated voltage (output cutoff)
Not provided
Not provided
Not provided
-10 to +60°C (70% load at 60°C)
-25 to +85°C
30 to 90% (no condensation)
30 to 90% (no condensation)
Natural air cooling
10 to 55 Hz
3 minutes
2 G
X, Y, and Z directions
One hour in each direction
10 G
With the unit resting on a smooth-surfaced wooden plank, at least 10 mm thick, each side of the unit is
raised 50 mm and allowed to fall freely. This is performed three times for each of the four sides.
Derating is necessary depending on the installation conditions. Refer to (6) below.
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
Open frame (PCB only)
115 x 50 x 17 (W x D x H)
about 70 g
CEM-1
Designed to meet UL 1950 / Designed to meet CSA C22.2 No. 234 Level 3 /
Designed to comply with the Electrical Appliance and Materials Control Law
Designed to meet FCC Class B (100 to 120 V AC) / Designed to meet VCCI Class 2
Note 6: Insulation specifications are for normal temperature and humidity.
Note 7: To reset the power supply, turn off the input power, then re-apply power after about one minute.
Note 8: Under standard input/output conditions at an ambient temperature of 25°C.
Note 9: Values in parentheses are with the high harmonic reactor installed.
Note 10: If shutdown occurs due to over current or over voltage conditions, remove the source of the problem and re-apply power after about one minute powered off.
*"Under rated input/output conditions"means that the switching power supply is operated under the rated input voltage, rated output current, rated frequency, and normal
temperature and humidity.
CN2 CN2
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Adjustment
knob
Adjustment
knob
Adjustment
knob
4- 3.5
φ
140
5
50 ±125 ±1
40
5
150 ±1
1
4
CN2
CN1
L1
N
FG5
Component mounting
area
Mounting holes
[lead cut]
3 mm max.
CN2 CN2
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Adjustment
knob
Adjustment
knob
Adjustment
knob
4- 3.5
108
3.5
50 ±123 ±1
43
3.5
115 ±1
RV1
4
1
CN2
CN2
7
4
1
φ
Component mounting
area
Mounting holes
[lead cut]
3 mm max.
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
8
Compatible connectors and contacts
* Compatible hand crimping tool for crimped connectors (made by JST):
YC-110R, YRS-11
CN1
CN2
Pin
number
1
2
3
4
5
6
7
1 - 2
3 - 4
Function
AC (L)
NC
NC
AC (N)
NC
NC
FG
–
+
Connector
B3 (7.5) B-
XH-A
(JST)
B4B-XH-A
(JST)
Compatible
connectors
XHP-7 (JST)
XHP-4
(JST)
Compatible
contacts
SXH-001
T-P0.6
(JST)
or
BXH-001
T-P0.6
(JST)
Compatible connectors and contacts
CN1
CN2
Pin
number
1
2
3
4
5
1 - 2
3 - 4
Function
AC (L)
NC
AC (N)
NC
FG
–
+
Connector
B5P3-VH
(JST)
B4P-VH
(JST)
Compatible
connectors
VHR-5N
(JST)
VHR-4N
(JST)
Compatible
contacts
SVH-21T-
P1.1 (JST)
25 W
(weight: approx. 85 g)
Model
CSH025-05
CSH025-12
CSH025-15
CSH025-24
50 W
(weight: approx. 150 g)
Model
CSH050-05
CSH050-12
CSH050-15
CSH050-24
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
9
CN2 CN2
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Adjustment
knob
Adjustment
knob
Adjustment
knob
Compatible connectors and contacts
CN1
CN2
Pin
number
1
3
5
1 - 4
5 - 8
Function
AC (L)
AC (N)
FG
–
+
Connector
B3P5-VH
(JST)
B8P-VH
(JST)
Compatible
connectors
VHR-5N
(JST)
VHR-8N
(JST)
Compatible
contacts
SVH-21T-
P1.1 (JST)
CN3
10mm minimum
10mm minimum
CN2
CN3
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Fin
Fin
Compatible connectors and contacts
CN1
CN2
CN3
Pin
number
1
3
5
1 - 6
1 - 7
Function
AC (L)
AC (N)
FG
+
–
Connector
B3P5-VH
(JST)
B6P-VH (JST)
B7P-VH (JST)
Compatible
connectors
VHR-5N
(JST)
VHR-6N (JST)
VHR-7N (JST)
Compatible
contacts
SVH-21T-
P1.1
(JST)
100 W
(weight: approx. 520 g)
Model
CSH100-05
CSH100-12
CSH100-15
CSH100-24
150 W
(weight: approx. 520 g)
Model
CSH150-05
CSH150-12
CSH150-15
CSH150-24
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
10
CN2 CN2
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Adjustment
knob
Adjustment
knob
Adjustment
knob
2- 3.5
90.5
3.5
49 ±1
17 ±1
45.5
3.5
94 ±1
RV1
2
1
CN2
CN1
7
4
1
φ
Component mounting
area
Mounting holes
[lead cut]
3 mm max.
Compatible connectors and contacts
* Compatible hand crimping tool for crimped connectors (made by JST):
YC-110R, YRS-11
CN1
CN2
Pin
number
1
2
3
4
5
6
7
1
2
Function
AC (L)
NC
NC
AC (N)
NC
NC
FG
–
+
Connector
B3 (7.5) B-
XH-A
(JST)
B2B-XH-A
(JST)
Compatible
connectors
XHP-7 (JST)
XHP-2
(JST)
Compatible
contacts
SXH-001
T-P0.6
(JST)
or
BXH-001
T-P0.6
(JST)
CN2 CN2
CN2
Vertical or horizontal mounting
Vertical mounting Horizontal mounting
Adjustment
knob
Adjustment
knob
Adjustment
knob
4- 3.5
108
3.5
50 ±1
17 ±1
43
3.5
115 ±1
RV1
4
1
CN2
CN1
7
4
1
φ
Component mounting
area
Mounting holes
[lead cut]
3 mm max.
Compatible connectors and contacts
* Compatible hand crimping tool for crimped connectors (made by JST):
YC-110R, YRS-11
CN1
CN2
Pin
number
1
2
3
4
5
6
7
1 - 2
3 - 4
Function
AC (L)
NC
NC
AC (N)
NC
NC
FG
–
+
Connector
B3 (7.5) B-
XH-A
(JST)
B4B-XH-A
(JST)
Compatible
connectors
XHP-7 (JST)
XHP-4
(JST)
Compatible
contacts
SXH-001
T-P0.6
(JST)
or
BXH-001
T-P0.6
(JST)
10 W
(weight: approx. 55 g)
Model
CSJ010-05
CSJ010-12
CSJ010-15
CSJ010-24
15 W
(weight: approx. 520 g)
Model
CSJ015-05
CSJ015-12
CSJ015-15
CSJ015-24
CSH Series 25W/50W/100W/150W
CSJ Series 10W/15W
11
Output current derating for ambient temperature,
installation conditions
%
100
70
–10 0 50 60 °C
Output current
Ambient temperature
%
100
70
60
–10 25 50 60 °C
Output current
Ambient temperature
%
100
70
–10 0 50 60 °C
Output current
Ambient temperature
%
100
70
–10 50 60 °C
Output current
Ambient temperature
%
100
70
–10 50 60 °C
Output current
Ambient temperature
%
100
70
–10 50 60 °C
Output current
Ambient temperature
(1) CSH025 (4) CSH150
(2) CSH050 (5) CSJ010
(3) CSH100 (6) CSJ015
