I N D U C T O R S October 2013 Inductors for High Frequency Circuits Multilayer Ceramic MHQ-Pseries MHQ1005P 1005 [0402 inch]* * Dimensions Code JIS[EIA] (For automobiles) (2/10) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (3/10) I N D U C T O R S Inductors for High Frequency Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 Multilayer Ceramic Overview of the MHQ-P Series FEATURES Unique ceramic material and configuration allows for the realization of high Q characteristics that are equivalent to that of air core wound inductors. Multilayer method allows for a lineup with fine increments of inductance. APPLICATION Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners and other high frequency circuits for the mobile communication industry PART NUMBER CONSTRUCTION MHQ Series name 1005 LxWxH Dimensions (mm) 1005 1.0x0.5x0.5 P Characteristics P 1N0 B Inductance (nH) 1N1 1.1 11N 11 Inductance tolerance B 0.1nH C 0.2nH S 0.3nH G 2% H 3% J 5% T Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage temperature temperature (pieces/reel) C C MHQ1005P -55 to +125 -55 to +125 10000 The Storage temperature range is for after the circuit board is mounted. Type Individual weight mg 1 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (4/10) I N D U C T O R S Overview of the MHQ-P Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s max. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (5/10) I N D U C T O R S MHQ-Pseries MHQ1005P Type 0.600.05 SHAPE & DIMENSIONS 0.120.05 0.120.05 0.500.10 1.000.05 0.220.08 Dimensions in mm 0.220.08 0.65 RECOMMENDED LAND PATTERN 0.35 0.50 0.35 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (6/10) I N D U C T O R S MHQ-Pseries MHQ1005P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 12 15 Tolerance 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 2%, 3%, 5% 2%, 3%, 5% 2%, 3%, 5% 2%, 3%, 5% 2%, 3%, 5% 2%, 3%, 5% 2%, 3%, 5% Self-resonant L measuring Q measuring frequency Q frequency frequency (GHz) min. (MHz) (MHz) min. typ. 100 -- 250 15.0 20.0 100 -- 250 14.0 20.0 100 -- 250 13.0 18.3 100 -- 250 12.0 20.0 100 23 250 11.0 19.7 100 23 250 10.0 15.2 100 23 250 9.0 15.1 100 23 250 8.0 11.5 100 23 250 8.0 12.1 100 23 250 6.5 9.8 100 23 250 6.5 9.6 100 23 250 6.0 9.4 100 23 250 6.0 9.0 100 23 250 5.5 8.4 100 23 250 5.0 7.7 100 23 250 5.0 7.1 100 23 250 5.0 7.7 100 23 250 4.5 7.2 100 23 250 4.5 6.5 100 23 250 4.0 5.9 100 23 250 4.0 5.8 100 23 250 4.0 5.6 100 23 250 3.6 4.9 100 23 250 3.4 4.5 100 23 250 3.3 4.6 100 23 250 2.8 3.8 100 23 250 2.3 3.2 DC resistance (: ) max. 0.03 0.03 0.03 0.03 0.04 0.04 0.04 0.05 0.06 0.06 0.07 0.08 0.08 0.09 0.09 0.10 0.11 0.12 0.13 0.13 0.14 0.16 0.16 0.17 0.19 0.24 0.28 typ. 0.01 0.02 0.01 0.01 0.02 0.02 0.03 0.03 0.04 0.04 0.04 0.06 0.06 0.07 0.07 0.08 0.08 0.09 0.10 0.09 0.10 0.12 0.12 0.13 0.15 0.19 0.22 Rated current Part No.* (mA) max. 1200 1200 1200 1200 1000 1000 1000 1000 1000 1000 900 900 900 900 900 800 800 800 800 700 700 600 550 550 500 450 400 MHQ1005P1N0T MHQ1005P1N1T MHQ1005P1N2T MHQ1005P1N3T MHQ1005P1N5T MHQ1005P1N6T MHQ1005P1N8T MHQ1005P2N0T MHQ1005P2N2T MHQ1005P2N4T MHQ1005P2N7T MHQ1005P3N0T MHQ1005P3N3T MHQ1005P3N6T MHQ1005P3N9T MHQ1005P4N3T MHQ1005P4N7T MHQ1005P5N1T MHQ1005P5N6T MHQ1005P6N2T MHQ1005P6N8T MHQ1005P7N5T MHQ1005P8N2T MHQ1005P9N1T MHQ1005P10NT MHQ1005P12NT MHQ1005P15NT The " " of the Part Number contains the inductance tolerance code, B0.1nH, C0.2nH, S0.3nH, G2%, H3%or J5%. The " " of the Part Number contains the internal code. Short bar residual inductance =0.556nH Measurement equipment Measurement item Product No. L, Q 4291B+16193A Self-resonant frequency 8720C DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (7/10) I N D U C T O R S MHQ-Pseries MHQ1005P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.3 2.6 2.9 3.2 3.5 3.8 4.2 4.6 5.0 5.5 6.1 6.7 7.3 8.0 8.9 9.8 12 15 800MHz 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.1 2.3 2.6 2.9 3.2 3.5 3.8 4.2 4.6 5.0 5.5 6.1 6.7 7.3 8.1 9.0 9.9 12 15 1.8GHz 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.4 4.7 5.2 5.7 6.5 7.2 7.9 8.9 9.9 11.1 14 18 2.0GHz 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.0 3.3 3.6 4.0 4.5 4.8 5.3 5.8 6.7 7.4 8.1 9.2 10.3 11.6 14 20 2.4GHz 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 2.2 2.4 2.7 3.1 3.4 3.7 4.1 4.6 4.9 5.4 6.1 7.0 7.8 8.5 9.8 11.2 12.6 16 23 Q typ. 500MHz 56min. 56min. 56min. 56min. 56 60 52 54 47 45 45 47 41 41 40 41 38 41 39 45 42 38 42 38 39 39 37 800MHz 76min. 76min. 76min. 76min. 76 78 72 70 62 59 57 59 55 53 53 54 50 52 51 56 53 49 53 49 51 49 45 1.8GHz 126min. 126min. 126min. 126min. 126 136 123 108 104 98 87 92 91 87 87 86 82 79 81 84 77 76 77 73 74 67 57 2.0GHz 130min. 130min. 130min. 130min. 130 144 129 113 110 102 91 97 95 91 91 89 85 83 84 87 80 79 80 75 75 68 57 2.4GHz 160min. 160min. 160min. 160min. 160 174 152 132 129 120 108 116 112 107 105 102 98 97 95 99 91 87 88 79 77 70 54 Part No.* MHQ1005P1N0T MHQ1005P1N1T MHQ1005P1N2T MHQ1005P1N3T MHQ1005P1N5T MHQ1005P1N6T MHQ1005P1N8T MHQ1005P2N0T MHQ1005P2N2T MHQ1005P2N4T MHQ1005P2N7T MHQ1005P3N0T MHQ1005P3N3T MHQ1005P3N6T MHQ1005P3N9T MHQ1005P4N3T MHQ1005P4N7T MHQ1005P5N1T MHQ1005P5N6T MHQ1005P6N2T MHQ1005P6N8T MHQ1005P7N5T MHQ1005P8N2T MHQ1005P9N1T MHQ1005P10NT MHQ1005P12NT MHQ1005P15NT The " " of the Part Number contains the inductance tolerance code, B0.1nH, C0.2nH, S0.3nH, G2%, H3%or J5%. The " " of the Part Number contains the internal code. Measurement equipment Product No. Manufacturer 4291B+16193A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (8/10) I N D U C T O R S MHQ-Pseries MHQ1005P Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 1000 100 15N Inductance(nH) 12N 10N 8N2 10 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1N0 1 0 10 100 1000 10000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991+16193A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (9/10) I N D U C T O R S MHQ-Pseries MHQ1005P Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 200 1N2 1N0 1N5 1N8 180 160 2N2 140 2N7 3N3 3N9 120 4N7 Q 5N6 100 6N8 8N2 80 10N 60 12N 40 15N 20 0 10 100 1000 10000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991+16193A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm (10/10) I N D U C T O R S MHQ-Pseries Packaging Style REEL DIMENSIONS o60min. 1.0 2.00.5 8.4 +2.0 -0.0 o130.2 14.4max. o210.8 o1802.0 Dimensions in mm 3.50.05 Cavity Type MHQ1005P A 1.150.10 B 0.750.10 K 0.8 max. A 8.00.3 Sprocket hole 1.5 +0.1 -0.0 1.750.1 TAPE DIMENSIONS K B 4.00.1 2.00.05 160min. Taping 2.00.05 200min. Drawing direction 300min. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mhq_en.fm