LM119QML LM119QML High Speed Dual Comparator Literature Number: SNOSAN3A LM119QML High Speed Dual Comparator General Description Features The LM119 is a precision high speed dual comparator fabricated on a single monolithic chip. It is designed to operate over a wide range of supply voltages down to a single 5V logic supply and ground. Further, it has higher gain and lower input currents than devices like the LM710. The uncommitted collector of the output stage makes the LM119 compatible with RTL, DTL and TTL as well as capable of driving lamps and relays at currents up to 25 mA. Although designed primarily for applications requiring operation from digital logic supplies, the LM119 is fully specified for power supplies up to 15V. It features faster response than the LM111 at the expense of higher power dissipation. However, the high speed, wide operating voltage range and low package count make the LM119 much more versatile than older devices like the LM711. Available with radiation guaranteed 100 krad(Si) -- High Dose Rate 100 krad(Si) -- ELDRS Free Two independent comparators Operates from a single 5V supply Typically 80 ns response time at 15V Minimum fan-out of 2 each side Maximum input current of 1 A over temperature Inputs and outputs can be isolated from system ground High common mode slew rate Ordering Information NS Part Number SMD Part Number LM119E/883 LM119E-SMD 86014012A NS Package Number Package Description E20A 20LD LCC E20A 20LD LCC H10C 10LD T0-100 Metal Can 8601401IA H10C 10LD T0-100 Metal Can LM119H-QMLV 5962-9679801VIA H10C 10LD T0-100 Metal Can LM119HRQMLV HIGH DOSE RATE (Note 13) 5962R9679801VIA 100 krad(Si) H10C 10LD T0-100 Metal Can LM119HRLQMLV ELDRS FREE (Note 14) 5962R9679802VIA 100 krad(Si) H10C 10LD T0-100 Metal Can LM119H/883 LM119H-SMD LM119J/883 J14A 14LD CERDIP 8601401CA J14A 14LD CERDIP LM119J-QMLV 5962-9679801VCA J14A 14LD CERDIP LM119JRQMLV HIGH DOSE RATE (Note 13) 5962R9679801VCA 100 krad(Si) J14A 14LD CERDIP LM119JRLQMLV ELDRS FREE (Note 14) 5962R9679802VCA 100 krad(Si) J14A 14LD CERDIP W10A 10LD CERPAK LM119J-SMD LM119W/883 LM119W-SMD 8601401HA W10A 10LD CERPAK LM119W-QMLV 5962-9679801VHA W10A 10LD CERPAK LM119WRQMLV HIGH DOSE RATE (Note 13) 5962R9679801VHA 100 krad(Si) W10A 10LD CERPAK LM119WRLQMLV ELDRS FREE (Note 14) 5962R9679802VHA 100 krad(Si) W10A 10LD CERPAK LM119WG/883 WG10A 10LD Ceramic SOIC LM119WG-QMLV 5962-9679801VXA WG10A 10LD Ceramic SOIC LM119WGRQMLV HIGH DOSE RATE (Note 14) 5962R9679801VXA 100 krad(Si) WG10A 10LD Ceramic SOIC (c) 2009 National Semiconductor Corporation 201437 www.national.com LM119QML High Speed Dual Comparator January 13, 2009 LM119QML NS Part Number SMD Part Number NS Package Number LM119WGRLQMLV ELDRS FREE (Note 14) 5962R9679802VXA 100 krad(Si) WG10A LM119 MDE ELDRS FREE DIE (Notes 1, 14) 5962R9679802V9A 100 krad(Si) LM119 MDR HIGH DOSE RATE DIE (Notes 1, 13) 5962R9679801V9A 100 krad(Si) Package Description 10LD Ceramic SOIC Note 1: FOR ADDITIONAL DIE INFORMATION, PLEASE VISIT THE HI REL WEB SITE AT: www.national.com/analog/space/level_die Connection Diagrams Dual-In-Line Package Leadless Chip Carrier 20143704 Top View See NS Package Number J14A 20143708 Top View See NS Package Number E20A Metal Can Package 20143709 See NS Package Number W10A, WG10A 20143707 Case is connected to pin 5 (V-) Top View See NS Package Number H10C www.national.com 2 LM119QML Schematic Diagram 20143701 *Do not operate the LM119 with more than 16V between GND and V+ 3 www.national.com LM119QML Absolute Maximum Ratings (Note 2) Total Supply Voltage Output to Negative Supply Voltage Ground to Negative Supply Voltage Ground to Positive Supply Voltage Differential Input Voltage Input Voltage (Note 4) Power Dissipation (Note 3) Output Short Circuit Duration Storage Temperature Range 36V 36V 25V 18V 5V 15V 500 mW 10 sec -65C TA 150C -55C TA 125C 150C 260C Operating Ambient Temperature Range Maximum Junction Temperature (TJ) Lead Temperature (Soldering, 10 sec.) Thermal Resistance JA E Package (Still Air) E Package (500LF/Min Air flow) H Package (Still Air) H Package (500LF/Min Air flow) J Package (Still Air) J Package (500LF/Min Air flow) W Package (Still Air) W Package (500LF/Min Air flow) WG Package (Still Air) WG Package (500LF/Min Air flow) 89C/W 63C/W 162C/W 88C/W 94C/W 52C/W 215C/W 132C/W 215C/W 132C/W JC E Package H Package J Package W Package WG Package Package Weight E Package H Package J Package W Package WG Package ESD rating (Note 5) www.national.com 5C/W 31C/W 11C/W 13C/W 13C/W TBD TBD TBD TBD 225mg 800V 4 Mil-Std-883, Method 5005 - Group A Subgroup Description Temp C 1 Static tests at 25 2 Static tests at 125 3 Static tests at -55 4 Dynamic tests at 25 5 Dynamic tests at 125 6 Dynamic tests at -55 7 Functional tests at 25 8A Functional tests at 125 8B Functional tests at -55 9 Switching tests at 25 10 Switching tests at 125 11 Switching tests at -55 12 Settling time at 25 13 Settling time at 125 14 Settling time at -55 5 www.national.com LM119QML Quality Conformance Inspection LM119QML LM119/883 Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. Symbol +ICC Parameter Positive Supply Current Conditions ILeak IIB Negative Supply Current Output Leakage Current Input Bias Current Notes Min VCC = 15V, VO = Low V+ -ICC VCM = 0V = 5.6V thru 1.4K VCC = 15V, VO = Low -4.2 V+ -4.5 = 5.6V thru 1.4K +V CC = 15V, VCC = -1V, VGnd = 0V, VO = 35V, VI = 5mV Input Offset Current 2 mA 1 mA 2 1.8 A 1 9.5 A 2 3 1 0.475 A 1 .95 A 2, 3 -3.8 3.8 mV 1 VCM = 1V, RS 5K -6.8 6.8 mV 2, 3 +V -3.8 3.8 mV 1 VCM = 3V, RS 5K -6.8 6.8 mV 2, 3 VCC = 15V, VCM = 12V, -3.8 3.8 mV 1 RS 5K -6.8 6.8 mV 2, 3 VCC = 15V, VCM = -12V, -3.8 3.8 mV 1 -6.8 6.8 mV 2, 3 -75 75 nA 1 -100 100 nA 2, 3 +V CC CC CC = 5V, -VCC = 0V, = 5V, -VCC = 0V, +V CC CC = 5V, -VCC = 0V, VCM = 1V = 5V, -VCC = 0V, VCM = 3V -75 75 nA 1 -100 100 nA 2, 3 -75 75 nA 1 -100 100 nA 2, 3 -75 75 nA 1 -100 100 nA 2, 3 1.5 V 1 VCC = 15V, IO = 25mA, VI = -5mV - CC = 5V, VCC = 0V, IO= 4.0mA (Note 12) 0.4 V 1, 2 (Note 12) 0.6 V 3 VCC = 15V, Delta VO = 12V, (Note 9), (Note 10) 10.5 K 4 (Note 9), (Note 10) 10 K 5, 6 (Note 9), (Note 11) 8.0 K 4 (Note 9), (Note 11) 5.0 K 5 (Note 9), (Note 11) 5.8 K 6 RL = 1.4K +V CC = 5V, -VCC = 0V, Delta VO = 4.5V, RL = 1.4K www.national.com mA 2, 3 +V Voltage Gain 11.5 A VCC = 15V, VCM = -12V AV 1 0.95 VCC = 15V, VCM = 12V Output Saturation Voltage mA A +V VSat 11 A RS 5K IIO Subgroups 10.0 = 5V, -VCC = 0V, VCM = 1.5V Input Offset Voltage Units 0.475 VCC = 15V +V VIO Max 6 LM119QML LM119-SMD Electrical Characteristics SMD 8601401 DC Parameters The following conditions apply, unless otherwise specified. Symbol +ICC Parameter Positive Supply Current Conditions ILeak IIB Negative Supply Current Output Leakage Current Input Bias Current Notes Min VCC = 15V, VO = Low V+ -ICC VCM = 0V = 5.6V thru 1.4K Input Offset Voltage 1 -4.5 mA 2 -6.0 mA 3 = 5.6V thru 1.4K +V CC = 15V, VCC = -1V, VGnd = 0V, VO = 35V (Note 6) 1.8 A 1 (Note 6) 10 A 2, 3 0.475 A 1 0.95 A 2, 3 0.475 A 1 2, 3 VCC = 15V +V CC = 5V +V CC = 5V, VCM = 1V, RS 5K (Note 7) CC = 5V, VCM = 3V, .95 A (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 -3.8 3.8 mV 1 RS 5K -6.8 6.8 mV 2, 3 VCC = 15V, VCM = -12V, -3.8 3.8 mV 1 -6.8 6.8 mV 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 +V CC = 5V, VCM = 1V +V CC = 5V, VCM = 3V VCC = 15V, VCM = -12V Output Saturation Voltage -75 75 nA 1 -100 100 nA 2, 3 -75 75 nA 1 -100 100 nA 2, 3 CC = 5V (Note 7), (Note 8) 1.0 3.0 V 1, 2, 3 VCC = 15V (Note 8) -12 12 V 1, 2, 3 VCC = 15V, IO = 25mA, (Note 6) 1.5 V 1, 2, 3 0.4 V 1, 2 0.6 V 3 10.5 K 4 +V VI -5mV +V CC = 3.5V, -VCC = -1V, VI -6mV, IO 3.2mA AV Voltage Gain VCC = 15V, Delta VO = 12V, Common Mode Rejection Ratio (Note 9) RL = 1.4K (Note 9) 10 K 5, 6 +V (Note 7), (Note 9) 8.0 K 4 (Note 7), (Note 9) 5.0 K 5 (Note 7), (Note 9) 5.8 K 6 80 dB 4 CC = 5V, VCC = 0V, Delta VO = 4.5V, RL = 1.4K CMRR 11.5 V+ VCC = 15V, VCM = 12V VSat 1 2, 3 RS 5K Input Voltage Range mA mA VCC = 15V, VCM = 12V, VI 11 mA RS 5K Input Offset Current Subgroups -4.2 +V IIO Units VCC = 15V, VO = Low (Note 7) VIO Max VCC = 15V, VCM = 12V 7 www.national.com LM119QML LM119 Electrical Characteristics SMD 5962-9679801, HIGH DOSE RATE DC Parameters The following conditions apply, unless otherwise specified. Symbol +ICC Parameter Positive Supply Current Conditions ILeak IIB Negative Supply Current Output Leakage Current Input Bias Current Notes Min VCC = 15V, VO = Low V+ -ICC VCM = 0V = 5.6V thru 1.4K Input Offset Voltage 1 -4.5 mA 2 -6.0 mA 3 = 5.6V thru 1.4K +V CC = 15V, VCC = -1V, VGnd = 0V, VO = 35V (Note 6) 1.8 A 1 (Note 6) 10 A 2, 3 0.475 A 1 0.95 A 2, 3 0.475 A 1 2, 3 VCC = 15V +V CC = 5V +V CC = 5V, VCM = 1V, RS 5K (Note 7) CC = 5V, VCM = 3V, .95 A (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 -3.8 3.8 mV 1 RS 5K -6.8 6.8 mV 2, 3 VCC = 15V, VCM = -12V, -3.8 3.8 mV 1 -6.8 6.8 mV 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 +V CC = 5V, VCM = 1V +V CC = 5V, VCM = 3V VCC = 15V, VCM = -12V Output Saturation Voltage -75 75 nA 1 -100 100 nA 2, 3 -75 75 nA 1 -100 100 nA 2, 3 CC = 5V (Note 7), (Note 8) 1.0 3.0 V 1, 2, 3 VCC = 15V (Note 8) -12 12 V 1, 2, 3 VCC = 15V, IO = 25mA, (Note 6) 1.5 V 1, 2, 3 0.4 V 1, 2 0.6 V 3 10.5 K 4 +V VI -5mV +V CC = 3.5V, -VCC = -1V, VI -6mV, IO 3.2mA AV Voltage Gain VCC = 15V, Delta VO = 12V, Common Mode Rejection Ratio www.national.com (Note 9) RL = 1.4K (Note 9) 10 K 5, 6 +V (Note 7), (Note 9) 8.0 K 4 (Note 7), (Note 9) 5.0 K 5 (Note 7), (Note 9) 5.8 K 6 80 dB 4 CC = 5V, VCC = 0V, Delta VO = 4.5V, RL = 1.4K CMRR 11.5 V+ VCC = 15V, VCM = 12V VSat 1 2, 3 RS 5K Input Voltage Range mA mA VCC = 15V, VCM = 12V, VI 11 mA RS 5K Input Offset Current Subgroups -4.2 +V IIO Units VCC = 15V, VO = Low (Note 7) VIO Max VCC = 15V, VCM = 12V 8 DC DELTA Parameters The following conditions apply, unless otherwise specified. VCM = 0V, Delta calculations performed on QMLV devices at group B, subgroup 5 only. Symbol +ICC Min Max Units Subgroups -1.0 1.0 mA 1 -0.5 0.5 mA 1 -0.4 0.4 mV 1 Min Max Units Subgroups VCC = 15V 1.0 A 1 VCC = 5V 1.0 A 1 Parameter Positive Supply Current Conditions VCC = 15V, VO = Low V+ -ICC Negative Supply Current Notes = 5.6V thru 1.4K VCC = 15V, VO = Low V+ = 5.6V thru 1.4K VIO Input Offset Voltage +V CC = 5V, VCM = 1V, RS 5K SMD 5962-9679801, High Dose Rate 100K Post Radiation Parameters @ 25C The following conditions apply, unless otherwise specified. Symbol IIB VIO Parameter Input Bias Current Input Offset Voltage (Note 13) VCM = 0V Conditions Notes +V CC = 5V, VCM = 1V, RS 5K -4.0 4.0 mV 1 +V CC = 5V, VCM = 3V, RS 5K -4.0 4.0 mV 1 -4.0 4.0 mV 1 -4.0 4.0 mV 1 VCC = 15V, VCM = 12V, RS 5K VCC = 15V, VCM = -12V, RS 5K 9 www.national.com LM119QML SMD 5962-9679801, HIGH DOSE RATE LM119QML LM119 Electrical Characteristics SMD 5962-9679802, ELDRS FREE DC Parameters The following conditions apply, unless otherwise specified. Symbol +ICC Parameter Positive Supply Current Conditions ILeak IIB Negative Supply Current Output Leakage Current Input Bias Current Notes Min VCC = 15V, VO = Low V+ -ICC VCM = 0V = 5.6V thru 1.4K Input Offset Voltage 1 -4.5 mA 2 -6.0 mA 3 = 5.6V thru 1.4K +V CC = 15V, VCC = -1V, VGnd = 0V, VO = 35V (Note 6) 1.8 A 1 (Note 6) 10 A 2, 3 0.475 A 1 0.95 A 2, 3 0.475 A 1 2, 3 VCC = 15V +V CC = 5V +V CC = 5V, VCM = 1V, RS 5K (Note 7) CC = 5V, VCM = 3V, .95 A (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 (Note 7) -3.8 3.8 mV 1 (Note 7) -6.8 6.8 mV 2, 3 -3.8 3.8 mV 1 RS 5K -6.8 6.8 mV 2, 3 VCC = 15V, VCM = -12V, -3.8 3.8 mV 1 -6.8 6.8 mV 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 (Note 7) -75 75 nA 1 (Note 7) -100 100 nA 2, 3 +V CC = 5V, VCM = 1V +V CC = 5V, VCM = 3V VCC = 15V, VCM = -12V Output Saturation Voltage -75 75 nA 1 -100 100 nA 2, 3 -75 75 nA 1 -100 100 nA 2, 3 CC = 5V (Note 8), (Note 8) 1.0 3.0 V 1, 2, 3 VCC = 15V (Note 8) -12 12 V 1, 2, 3 VCC = 15V, IO = 25mA, (Note 6) 1.5 V 1, 2, 3 0.4 V 1, 2 0.6 V 3 10.5 K 4 +V VI -5mV +V CC = 3.5V, -VCC = -1V, VI -6mV, IO 3.2mA AV Voltage Gain VCC = 15V, Delta VO = 12V, Common Mode Rejection Ratio www.national.com (Note 9) RL = 1.4K (Note 9) 10 K 5, 6 +V (Note 7), (Note 9) 8.0 K 4 (Note 7), (Note 9) 5.0 K 5 (Note 7), (Note 9) 5.8 K 6 80 dB 4 CC = 5V, VCC = 0V, Delta VO = 4.5V, RL = 1.4K CMRR 11.5 V+ VCC = 15V, VCM = 12V VSat 1 2, 3 RS 5K Input Voltage Range mA mA VCC = 15V, VCM = 12V, VI 11 mA RS 5K Input Offset Current Subgroups -4.2 +V IIO Units VCC = 15V, VO = Low (Note 7) VIO Max VCC = 15V, VCM = 12V 10 DC DELTA Parameters The following conditions apply, unless otherwise specified. VCM = 0V, Delta calculations performed on QMLV devices at group B, subgroup 5 only. Symbol +ICC Parameter Positive Supply Current Conditions VCC = 15V, VO = Low V+ -ICC Negative Supply Current Notes Min Max Units Subgroups -1.0 1.0 mA 1 -0.5 0.5 mA 1 -0.4 0.4 mV 1 = 5.6V thru 1.4K VCC = 15V, VO = Low V+ = 5.6V thru 1.4K VIO Input Offset Voltage +V CC = 5V, VCM = 1V, RS 5K SMD 5962-9679802, ELDRS FREE 100K Post Radiation Parameters @ 25C (Note 14) The following conditions apply, unless otherwise specified. Symbol IIB VIO Max Units Subgroups VCC = 15V 1.0 A 1 VCC = 5V 1.0 A 1 Parameter Input Bias Current Input Offset Voltage VCM = 0V Conditions Notes Min +V CC = 5V, VCM = 1V, RS 5K -4.0 4.0 mV 1 +V CC = 5V, VCM = 3V, RS 5K -4.0 4.0 mV 1 -4.0 4.0 mV 1 -4.0 4.0 mV 1 VCC = 15V, VCM = 12V, RS 5K VCC = 15V, VCM = -12V, RS 5K Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), JA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/ JA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 4: For supply voltages less than 15V the absolute maximum input voltage is equal to the supply voltage. Note 5: Human Body model, 1.5K in series with 100pF. Note 6: VI 8mV at extremes for ILeak and VI -8mV at extremes for VSat (VI to exceed VOS. Note 7: 5V differential across +VCC and -VCC. Note 8: Parameter guaranteed by VIO and IIO tests. Note 9: K = V/mV. Note 10: Gain is computed with an output swing from +13.5V to +1.5V. Note 11: Gain is computed with an output swing from +5.0V to +0.5V. Note 12: Output is monitored by measuring VI with limits from 0 to 6mV at all temperatures Note 13: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate sensitivity. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, per Test Method 1019, Condition A. Note 14: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. Low dose rate testing has been performed on a wafer-by-wafer basis, per Test Method 1019, Condition D of MIL-STD-883, with no enhanced low dose rate sensitivity (ELDRS). 11 www.national.com LM119QML SMD 5962-9679802, ELDRS FREE LM119QML Typical Performance Characteristics Input Currents Common Mode Limits 20143710 20143711 Transfer Function Response Time for Various Input Overdrives 20143712 20143713 Response Time for Various Input Overdrives Input Characteristics 20143715 20143714 www.national.com 12 LM119QML Response Time for Various Input Overdrives Response Time for Various Input Overdrives 20143716 20143717 Supply Current Output Saturation Voltage 20143718 20143719 Supply Current Output Limiting Characteristics 20143720 20143721 13 www.national.com LM119QML Typical Applications (Note Pin numbers are for metal can package. ) Relay Driver 20143705 Note 15: Pin numbers are for metal can package. Window Detector 20143706 VOUT = 5V for VLT VIN VUT VOUT = 0 for VIN VLTor VIN VUT www.national.com 14 Date Released Revision 07/24/08 01/13/09 A B Section Originator New release to corporate format Features, Ordering Info., Electrical Section, Notes 13 and 14 15 Changes L. Lytle 2 MDS datasheets converted into one corporate data sheet format. Added Radiation information. MDS data sheets MNLM119-X Rev. 0F1 & MDLM119-X Rev 2A2 will be archived. Larry McGee Added reference to ELDRS and Die NSID's to data sheet. Correction from: 100k rd(Si) to 100 krad(Si) in ordering info. Changed wording in Notes 13 and 14 Revision A will be Archived. www.national.com LM119QML Revision History LM119QML Physical Dimensions inches (millimeters) unless otherwise noted Metal Can Package (H) NS Package Number H10C Cavity Dual-In-Line Package (J) NS Package Number J14A www.national.com 16 LM119QML Ceramic Flatpack (W) NS Package Number W10A Ceramic SOIC (WG) NS Package Number WG10A 17 www.national.com LM119QML Metal Leadless Chip Carrier (LCC) NS Package Number E20A www.national.com 18 LM119QML Notes 19 www.national.com LM119QML High Speed Dual Comparator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise(R) Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors Solar Magic(R) www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University(R) www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated