DS1302 DS1302 Trickle Charge Timekeeping Chip FEATURES PIN ASSIGNMENT * Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 * 31 x 8 RAM for scratchpad data storage * Serial I/O for minimum pin count VCC2 1 8 VCC1 X1 2 7 SCLK X2 3 6 I/O GND 4 5 RST DS1302 8-PIN DIP (300 MIL) * 2.5-5.5 volt full operation - Optional 2.0-5.5 volt full operation also available VCC2 X1 X2 GND * Uses less than 300 nA at 2.5 volts * Single-byte or multiple-byte (burst mode) data trans- 1 2 3 4 8 7 6 5 VCC1 SCLK I/O RST DS1302S 8-PIN SOIC (200 MIL) DS1302Z 8-PIN SOIC (150 MIL) fer for read or write of clock or RAM data * 8-pin DIP or optional 8-pin SOIC's for surface mount * Simple 3-wire interface * TTL-compatible (VCC = 5V) * Optional industrial temperature range -40C to +85C * DS1202 compatible * Added features over DS1202 - Optional trickle charge capability to VCC1 - Dual power supply pins for primary and backup power supplies - Backup power supply pin can be used for battery or super cap input - Additional scratchpad memory (7 bytes) PIN DESCRIPTION X1, X2 GND RST I/O SCLK VCC1, VCC2 - - - - - - 32.768 kHz Crystal Pins Ground Reset Data Input/Output Serial Clock Power Supply Pins ORDERING INFORMATION PART # DS1302 DS1302S DS1302Z DESCRIPTION Serial Timekeeping Chip; 8-pin DIP Serial Timekeeping Chip; 8-pin SOIC (200 mil) Serial Timekeeping Chip; 8-pin SOIC (150 mil) DESCRIPTION The DS1302 Trickle Charge Timekeeping Chip contains a real time clock/calendar and 31 bytes of static RAM. It communicates with a microprocessor via a simple serial interface. The real time clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with less than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with an AM/PM indicator. Copyright 1995 by Dallas Semiconductor Corporation. All Rights Reserved. For important information regarding patents and other intellectual property rights, please refer to Dallas Semiconductor data books. Interfacing the DS1302 with a microprocessor is simplified by using synchronous serial communication. Only three wires are required to communicate with the clock/ RAM: (1) RST (Reset), (2) I/O (Data line), and (3) SCLK (Serial clock). Data can be transferred to and from the clock/RAM one byte at a time or in a burst of up to 31 bytes. The DS1302 is designed to operate on very low power and retain data and clock information on less than 1 microwatt. 041697 1/12 DS1302 After the first eight clock cycles have loaded the command word into the shift register, additional clocks will output data for a read or input data for a write. The number of clock pulses equals eight plus eight for byte mode or eight plus up to 248 for burst mode. The DS1302 is the successor to the DS1202. In addition to the basic timekeeping functions of the DS1202, the DS1302 has the additional features of dual power pins for primary and back-up power supplies, programmable trickle charger for VCC1, and seven additional bytes of scratchpad memory. COMMAND BYTE The command byte is shown in Figure 2. Each data transfer is initiated by a command byte. The MSB (Bit 7) must be a logic "1". If it is zero, writes to the DS1302 will be disabled. Bit 6 specifies clock/calendar data if logic "0" or RAM data if logic "1". Bits one through five specify the designated registers to be input or output, and the LSB (Bit 0) specifies a write operation (input) if logic "0" or read operation (output) if logic "1". The command byte is always input starting with the LSB (Bit 0). OPERATION The main elements of the Serial Timekeeper are shown in Figure 1: shift register, control logic, oscillator, real time clock, and RAM. To initiate any transfer of data, RST is taken high and eight bits are loaded into the shift register providing both address and command information. Data is serially input on the rising edge of the SCLK. The first eight bits specify which of 40 bytes will be accessed, whether a read or write cycle will take place, and whether a byte or burst mode transfer is to occur. DS1302 BLOCK DIAGRAM Figure 1 VCC1 32.768 kHz POWER CONTROL VCC2 GND X1 I/O OSCILLATOR AND DIVIDER REAL TIME CLOCK INPUT SHIFT REGISTERS X2 DATA BUS SCLK RST COMMAND AND CONTROL LOGIC 31 X 8 RAM ADDRESS BUS ADDRESS/COMMAND BYTE Figure 2 7 1 6 RAM CK 041697 2/12 5 4 3 2 1 A4 A3 A2 A1 A0 0 RD W DS1302 RESET AND CLOCK CONTROL All data transfers are initiated by driving the RST input high. The RST input serves two functions. First, RST turns on the control logic which allows access to the shift register for the address/command sequence. Second, the RST signal provides a method of terminating either single byte or multiple byte data transfer. A clock cycle is a sequence of a falling edge followed by a rising edge. For data inputs, data must be valid during the rising edge of the clock and data bits are output on the falling edge of clock. If the RST input is low all data transfer terminates and the I/O pin goes to a high impedance state. Data transfer is illustrated in Figure 3. At power-up, RST must be a logic "0" until VCC2.5 volts. Also SCLK must be at a logic "0" when RST is driven to a logic "1" state. DATA INPUT Following the eight SCLK cycles that input a write command byte, a data byte is input on the rising edge of the next eight SCLK cycles. Additional SCLK cycles are ignored should they inadvertently occur. Data is input starting with bit 0. DATA OUTPUT Following the eight SCLK cycles that input a read command byte, a data byte is output on the falling edge of the next eight SCLK cycles. Note that the first data bit to be transmitted occurs on the first falling edge after the last bit of the command byte is written. Additional SCLK cycles retransmit the data bytes should they inadvertently occur so long as RST remains high. This operation permits continuous burst mode read capability. Also, the I/O pin is tri-stated upon each rising edge of SCLK. Data is output starting with bit 0. However, when writing to RAM in burst mode it is not necessary to write all 31 bytes for the data to transfer. Each byte that is written to will be transferred to RAM regardless of whether all 31 bytes are written or not. CLOCK/CALENDAR The clock/calendar is contained in seven write/read registers as shown in Figure 4. Data contained in the clock/ calendar registers is in binary coded decimal format (BCD). CLOCK HALT FLAG Bit 7 of the seconds register is defined as the clock halt flag. When this bit is set to logic "1", the clock oscillator is stopped and the DS1302 is placed into a low-power standby mode with a current drain of less than 100 nanoamps. When this bit is written to logic "0", the clock will start. AM-PM/12-24 MODE Bit 7 of the hours register is defined as the 12- or 24-hour mode select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5 is the AM/PM bit with logic high being PM. In the 24-hour mode, bit 5 is the second 10 hour bit (20 - 23 hours). WRITE PROTECT BIT Bit 7 of the control register is the write protect bit. The first seven bits (bits 0 - 6) are forced to zero and will always read a zero when read. Before any write operation to the clock or RAM, bit 7 must be zero. When high, the write protect bit prevents a write operation to any other register. TRICKLE CHARGE REGISTER BURST MODE Burst mode may be specified for either the clock/calendar or the RAM registers by addressing location 31 decimal (address/command bits one through five = logical one). As before, bit six specifies clock or RAM and bit 0 specifies read or write. There is no data storage capacity at locations 9 through 31 in the Clock/Calendar Registers or location 31 in the RAM registers. Reads or writes in burst mode start with bit 0 of address 0. As in the case with the DS1202, when writing to the clock registers in the burst mode, the first eight registers must be written in order for the data to be transferred. This register controls the trickle charge characteristics of the DS1302. The simplified schematic of Figure 5 shows the basic components of the trickle charger. The trickle charge select (TCS) bits (bits 4 - 7) control the selection of the trickle charger. In order to prevent accidental enabling, only a pattern of 1010 will enable the trickle charger. All other patterns will disable the trickle charger. The DS1302 powers up with the trickle charger disabled. The diode select (DS) bits (bits 2 - 3) select whether one diode or two diodes are connected between VCC2 and VCC1. If DS is 01, one diode is selected or if DS is 10, two diodes are selected. If DS is 00 or 11, the trickle charger is disabled independent of 041697 3/12 DS1302 TCS. The RS bits (bits 0 - 1) select the resistor that is connected between VCC2 and VCC1. The resistor selected by the resistor select (RS) bits is as follows: RS Bits Resistor Typical Value 00 None None 01 R1 2K 10 R2 4K 11 R3 8K If RS is 00, the trickle charger is disabled independent of TCS. Diode and resistor selection is determined by the user according to the maximum current desired for battery or super cap charging. The maximum charging current can be calculated as illustrated in the following example. Assume that a system power supply of 5V is applied to VCC2 and a super cap is connected to VCC1. Also assume that the trickle charger has been enabled with 1 diode and resistor R1 between VCC2 and VCC1. The maximum current Imax would therefore be calculated as follows: Imax = (5.0V - diode drop) / R1 ~ (5.0V - 0.7V) / 2K ~ 2.2 mA Obviously, as the super cap charges, the voltage drop between VCC2 and VCC1 will decrease and therefore the charge current will decrease. to any of the eight clock/calendar registers (this includes the control register). The trickle charger is not accessible in burst mode. RAM The static RAM is 31 x 8 bytes addressed consecutively in the RAM address space. RAM BURST MODE The RAM command byte specifies burst mode operation. In this mode, the 31 RAM registers can be consecutively read or written (see Figure 4) starting with bit 0 of address 0. REGISTER SUMMARY A register data format summary is shown in Figure 4. CRYSTAL SELECTION A 32.768 kHz crystal can be directly connected to the DS1302 via pins 2 and 3 (X1, X2). The crystal selected for use should have a specified load capacitance (CL) of 6 pF. POWER CONTROL VCC1 provides low power operation in single supply and battery operated systems as well as low power battery backup. VCC2 provides the primary power in dual supply systems where VCC1 is connected to a backup source to maintain the time and data in the absence of primary power. CLOCK/CALENDAR BURST MODE The clock/calendar command byte specifies burst mode operation. In this mode the first eight clock/calendar registers can be consecutively read or written (see Figure 4) starting with bit 0 of address 0. If the write protect bit is set high when a write clock/calendar burst mode is specified, no data transfer will occur 041697 4/12 The DS1302 will operate from the larger of VCC1 or VCC2. When VCC2 is greater than VCC1 + 0.2V, VCC2 will power the DS1302. When VCC2 is less than VCC1, VCC1 will power the DS1302. DS1302 DATA TRANSFER SUMMARY Figure 3 SINGLE BYTE TRANSFER SCLK RST 0 R/W I/O 1 2 A0 A1 3 A2 4 A3 5 6 7 A4 R/C 1 0 1 2 ADDRESS COMMAND 3 4 5 6 7 DATA INPUT/OUTPUT BURST MODE TRANSFER SCLK RST 0 R/W I/O 1 1 2 1 3 1 4 1 5 6 7 1 R/C 1 ADDRESS COMMAND 0 1 DATA I/O BYTE 1 FUNCTION BYTE N SCLK n CLOCK 8 72 RAM 31 256 2 4 5 6 7 DATA I/O BYTE N 041697 5/12 DS1302 REGISTER ADDRESS/DEFINITION Figure 4 REGISTER ADDRESS A. CLOCK 7 6 5 REGISTER DEFINITION 4 3 2 1 SEC 1 0 0 0 0 0 0 MIN 1 0 0 0 0 0 1 HR 1 0 0 0 0 1 0 DATE 1 0 0 0 0 1 1 MONTH 1 0 0 0 1 0 0 DAY 1 0 0 0 1 0 1 YEAR 1 0 0 0 1 1 0 CONTROL 1 0 0 0 1 1 1 TRICKLE CHARGER 1 0 0 1 0 0 0 CLOCK BURST 1 0 1 1 1 1 1 RAM 0 1 1 0 0 0 0 0 RAM 30 1 1 1 1 1 1 0 RAM BURST 1 1 1 1 1 1 1 0 RD 00-59 CH 10 SEC SEC 00-59 0 10 MIN MIN W 01-12 00-23 12/ 24 0 W 01-28/29 01-30 01-31 0 0 10 DATE 01-12 0 0 0 10 M 01-07 0 0 0 0 W RD W RD RD RD W RD W RD W W RD W RD W B. RAM 041697 6/12 RD W RD W RD W RAM DATA 0 RAM DATA 30 HR HR DATE MONTH 0 10 YEAR 00-99 RD 10 A/P DAY YEAR WP 0 0 0 0 0 0 0 TCS TCS TCS TCS DS DS RS RS DS1302 DS1302 PROGRAMMABLE TRICKLE CHARGER Figure 5 R1 2K VCC1 VCC2 R2 4K PIN #8 PIN #1 R3 8K 1 OF 16 SELECT 1 OF 2 SELECT (NOTE: ONLY 1010 CODE ENABLES CHARGER TRICKLE CHARGE REGISTER 1 OF 3 SELECT TCS TCS TCS TCS DS DS RS RS BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 TCS = TRICKLE CHARGER SELECT DS = DIODE SELECT RS = RESISTOR SELECT 041697 7/12 DS1302 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.5V to +7.0V 0C to 70C -55C to +125C 260C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. The Dallas Semiconductor DS1302 is built to the highest quality standards and manufactured for long term reliability. All Dallas Semiconductor devices are made using the same quality materials and manufacturing methods. However, standard versions of the DS1302 are not exposed to environmental stresses, such as burn-in, that some industrial applications require. Products which have successfully passed through this series of environmental stresses are marked IND or N, denoting their extended operating temperature and reliability rating. For specific reliability information on this product, please contact the factory in Dallas at (972) 371-4448. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage VCC1, VCC2 SYMBOL (0C to 70C) MIN TYP MAX UNITS NOTES VCC1, VCC2 2.5 5.5 V 1, 11 Logic 1 Input VIH 2.0 VCC+0.3 V 1 +0.3 VIL VCC=2.5V -0.3 Logic 0 Input V 1 VCC=5V -0.3 +0.8 DC ELECTRICAL CHARACTERISTICS PARAMETER Input Leakage ILI I/O Leakage ILO Logic 1 Output Logic 0 Output Active Supply Current Timekeeping Current Standby Current Active Supply Current *Unless otherwise noted. 041697 8/12 (0C to 70C; VCC = 2.5 to 5.5V*) SYMBOL VOH VOL ICC1A ICC1T ICC1S ICC2A MIN VCC=2.5V 1.6 VCC=5V 2.4 TYP MAX UNITS NOTES +500 A 6 +500 A 6 V 2 V 3 mA 5 12 5, A 4 12 4,12 nA 10, 12, 14 mA 5 13 5, VCC=2.5V 0.4 VCC=5V 0.4 VCC1=2.5V 0.4 VCC1=5V 1.2 VCC1=2.5V 0.3 VCC1=5V 1 VCC1=2.5V 100 VCC1=5V 100 VCC2=2.5V 0.425 VCC2=5V 1.28 DS1302 DC ELECTRICAL CHARACTERISTICS (cont'd) PARAMETER Timekeeping Current Standby Current SYMBOL ICC2T ICC2S (0C to 70C; VCC = 2.5 to 5.5V*) MIN TYP MAX VCC2=2.5V 25.3 VCC2=5V 81 VCC2=2.5V 25 VCC2=5V 80 UNITS NOTES A 4 13 4,13 A 10 13 10, Trickle Charge Resistors R1 R2 R3 2 4 8 K K K Trickle Charger Diode Voltage Drop VTD 0.7 V *Unless otherwise noted. CAPACITANCE PARAMETER Input Capacitance (tA = 25C) SYMBOL CONDITION TYP MAX UNITS CI 10 pF I/O Capacitance CI/O 15 pF Crystal Capacitance CX 6 pF (0C to 70C; VCC = +5V 10%*) AC ELECTRICAL CHARACTERISTICS PARAMETER Data to CLK Setup CLK to Data Hold CLK to Data Delay CLK Low Time CLK High Time CLK Frequency CLK Rise and Fall RST to CLK Setup SYMBOL tDC tCDH tCDD tCL tCH tCLK tR, tF tCC NOTES MIN VCC =2.5V 200 VCC=5V 50 VCC=2.5V 280 VCC=5V 70 TYP MAX VCC=2.5V 800 VCC=5V 200 VCC=2.5V 1000 VCC=5V 250 VCC=2.5V 1000 VCC=5V 250 VCC=2.5V VCC=5V UNITS NOTES ns 7 ns 7 ns 7 8, 7, 8 9 ns 7 ns 7 MHz 7 0.5 DC 2.0 VCC=2.5V 2000 VCC=5V 500 ns VCC=2.5V 4 VCC=5V 1 s 7 *Unless otherwise noted. 041697 9/12 DS1302 (0C to 70C; VCC = +5V 10%*) AC ELECTRICAL CHARACTERISTICS (cont'd) PARAMETER SYMBOL CLK to RST Hold tCCH RST Inactive Time tCWH RST to I/O High Z tCDZ SCLK to I/O High Z tCCZ MIN VCC =2.5V 240 VCC=5V 60 VCC=2.5V 4 VCC=5V 1 TYP MAX VCC=2.5V 280 VCC=5V 70 VCC=2.5V 280 VCC=5V 70 UNITS NOTES ns 7 s 7 ns 7 ns 7 *Unless otherwise noted. TIMING DIAGRAM: READ DATA TRANSFER Figure 5 RST tCC SCLK tCCZ tCDH tCDZ tCDD tDC I/O tCDD 0 1 7 WRITE COMMAND BYTE 0 1 READ DATA BIT TIMING DIAGRAM: WRITE DATA TRANSFER Figure 6 tCWH RST tCC tCCH tR tCL tF SCLK tCDH tCH tDC I/O 0 1 WRITE COMMAND BYTE 041697 10/12 7 0 WRITE DATA DS1302 NOTES: 1. All voltages are referenced to ground. 2. Logic one voltages are specified at a source current of 1 mA at VCC=5V and 0.4 mA at VCC=2.5V, VOH=VCC for capacitive loads. 3. Logic zero voltages are specified at a sink current of 4 mA at VCC=5V and 1.5 mA at VCC=2.5V, VOL=GND for capacitive loads. 4. ICC1T and ICC2T are specified with I/O open, RST set to a logic "0", and clock halt flag=0 (oscillator enabled). 5. ICC1A and ICC2A are specified with the I/O pin open, RST high, SCLK=2 MHz at VCC=5V; SCLK=500 kHz, VCC=2.5V and clock halt flag=0 (oscillator enabled). 6. RST, SCLK, and I/O all have 40K pulldown resistors to ground. 7. Measured at VIH=2.0V or VIL=0.8V and 10 ms maximum rise and fall time. 8. Measured at VOH=2.4V or VOL=0.4V. 9. Load capacitance = 50 pF. 10. ICC1S and ICC2S are specified with RST, I/O, and SCLK open. The clock halt flag must be set to logic one (oscillator disabled). 11. VCC=VCC2, when VCC2>VCC1+0.2V; VCC=VCC1, when VCC1>VCC2. 12. VCC2=0 volts. 13. VCC1=0 volts. 14. Typical values are at 25C. DS1302 SERIAL TIMEKEEPER 8-PIN DIP 8 5 PKG B 1 4 A C E K 8-PIN DIM MIN MAX A IN. MM 0.360 9.14 0.400 10.16 B IN. MM 0.240 6.10 0.260 6.60 C IN. MM 0.120 3.05 0.140 3.56 D IN. MM 0.300 7.62 0.325 8.26 E IN. MM 0.015 0.38 0.040 1.02 F IN. MM 0.120 3.04 0.140 3.56 G IN. MM 0.090 2.29 0.110 2.79 H IN. MM 0.320 8.13 0.370 9.40 J IN. MM 0.008 0.20 0.012 0.30 K IN. MM 0.015 0.38 0.021 0.53 F G D J H 041697 11/12 DS1302 DS1302S SERIAL TIMEKEEPER 8-PIN SOIC (150 MIL AND 200 MIL) 8-PIN (150 MIL) PKG DIM MIN MAX MIN MAX A IN. MM 0.188 4.78 0.196 4.98 0.203 5.16 0.213 5.41 B IN. MM 0.150 3.81 0.158 4.01 0.203 5.16 0.213 5.41 C IN. MM 0.048 1.22 0.062 1.57 0.070 1.78 0.074 1.88 E IN. MM 0.004 0.10 0.010 0.25 0.004 0.10 0.010 0.25 F IN. MM 0.053 1.35 0.069 1.75 0.074 1.88 0.084 2.13 G IN. MM 0.050 BSC 1.27 BSC H IN. MM 0.230 5.84 0.244 6.20 0.302 7.67 0.318 8.08 J IN. MM 0.007 0.18 0.011 0.28 0.006 0.15 0.010 0.25 K IN. MM 0.012 0.30 0.020 0.51 0.013 0.33 0.020 0.51 L IN. MM 0.016 0.41 0.050 1.27 0.019 0.48 0.030 0.76 phi 0 8 0 8 56-G2008-001 56-G4010-001 041697 12/12 8-PIN (200 MIL)