SITOP PSU300M/300B
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SITOP power supply
SITOP PSU300M/300B
Manual
SITOP PSU300M 24 V/20 A
6EP1436
-3BA10
SITOP PSU300M 48 V/10 A
6EP1456
-3BA00
SITOP PSU300B 12 V/20 A
6EP1424
-3BA00
SITOP PSU300B 24 V/17 A
6EP1436
-3BA20
SITOP PSU300B 24 V/30 A
6EP1437-3BA20
11.2014
C98130
-A7574-A2-2-7629
Overview
Safety notes
1
Description, device design,
dimension drawing
2
Mounting/disassembly
3
Mounting position, mounting
clearances
4
Installation
5
Technical data
6
Safety, approvals, EMC
7
Ambient conditions
8
Applications
9
Environment
10
Service & Support
11
C98130-A7574-A2-2-7629
12/2014 Subject to change
Copyright © Siemens AG 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 3
Overview
The 3-phase power supply from the SITOP PSU300M/300B is a powerful, stabilized
technology power supply for automated machines and systems.
The key benefits of the product include:
3-phase 320 to 575 VAC wide-range input
Power boost during operation 300% for 25 ms (only PSU300M and PSU300B 12 V/20 A)
No lateral mounting clearances are required
150% extra power when loads with high input current are switched on (PSU300M and
PSU300B 12 V/20 A only)
Ambient temperature -25 (-10)...+70 °C
48 V / 10 A permits small cable cross-sections
Selectable short-circuit behavior
Soft characteristic curve for parallel switching or battery charging can be selected
Display of the operating state using 3 LEDs
Integrated signaling contact "DC 12 V O.K." / "DC 24 V O.K." / "DC 48 V O.K."
The properties of the PSU300B power supplies makes them ideal for battery charging
To increase the system availability, some reliable power supplies can be expanded using
SITOP supplementary modules (redundancy module, selectivity module, buffer module),
as well as SITOP DC-UPS modules.
Overview
SITOP PSU300M/300B
4 Manual, 11.2014, C98130-A7574-A2-2-7629
Ordering data
The following device versions are available:
Regulated SITOP PSU300M/300B power supply
Type
Order number
3-phase 400-500 V AC input,
Output 24 V DC / 20 A
6EP1436-3BA10
3-phase 400-500 V AC input,
Output 48 V DC / 10 A
6EP1456-3BA00
3-phase 400-500 V AC input,
Output 12 V DC / 20 A
6EP1424-3BA00
3-phase 400-500 V AC input,
Output 24 V DC / 17 A
6EP1436-3BA20
3-phase 400-500 V AC input,
Output 24 V DC / 30 A
6EP1437-3BA20
Accessories
Type
Order number
Device identification labels 20 mm × 7 mm, pastel turquoise
3RT1900-1SB20
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 5
Table of contents
Overview................................................................................................................................................. 3
1 Safety notes ............................................................................................................................................ 7
2 Description, device design, dimension drawing........................................................................................ 9
2.1 Device description ..................................................................................................................... 9
2.2 Connections and terminal designation.................................................................................... 10
2.3 Potentiometer .......................................................................................................................... 11
2.4 Status displays and signaling ................................................................................................. 12
2.5 Change-over switch ................................................................................................................ 15
2.6 Block diagram ......................................................................................................................... 16
2.7 Dimensions and weight ........................................................................................................... 17
3 Mounting/disassembly ........................................................................................................................... 19
4 Mounting position, mounting clearances ................................................................................................ 21
4.1 Standard mounting position .................................................................................................... 21
4.2 Other mounting positions ........................................................................................................ 24
4.2.1 6EP1436-3BA10 ..................................................................................................................... 24
4.2.2 6EP1456-3BA00 ..................................................................................................................... 26
4.2.3 6EP1424-3BA00 ..................................................................................................................... 28
4.2.4 6EP1436-3BA20 ..................................................................................................................... 30
4.2.5 6EP1437-3BA20 ..................................................................................................................... 32
5 Installation ............................................................................................................................................ 35
5.1 Line-side connection ............................................................................................................... 35
5.2 Output-side connection ........................................................................................................... 37
6 Technical data ...................................................................................................................................... 39
6.1 Input ........................................................................................................................................ 39
6.2 Output ..................................................................................................................................... 41
6.3 Efficiency ................................................................................................................................. 50
6.4 Closed-loop control ................................................................................................................. 53
6.5 Protection and monitoring ....................................................................................................... 54
6.6 MTBF ...................................................................................................................................... 55
6.7 Mechanical system ................................................................................................................. 55
6.8 Accessories ............................................................................................................................. 57
6.9 Dimension drawing ................................................................................................................. 57
Table of contents
SITOP PSU300M/300B
6 Manual, 11.2014, C98130-A7574-A2-2-7629
7 Safety, approvals, EMC ........................................................................................................................ 59
7.1 Safety ..................................................................................................................................... 59
7.2 Test voltage ............................................................................................................................ 60
7.3 Approvals ............................................................................................................................... 61
7.4 EMC ....................................................................................................................................... 61
8 Ambient conditions ................................................................................................................................ 63
9 Applications .......................................................................................................................................... 65
9.1 Parallel connection to increase power rating ......................................................................... 65
9.2 Parallel connection for redundancy ....................................................................................... 67
9.3 Series connection for increased voltage ................................................................................ 69
9.4 Overload protection in the 24 V output circuit ........................................................................ 70
9.5 Protection against short-time voltage dips ............................................................................. 71
9.6 Protecting against longer power failures ................................................................................ 72
9.7 Battery charging with SITOP PSU300B ................................................................................. 74
10 Environment ......................................................................................................................................... 77
11 Service & Support ................................................................................................................................. 79
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 7
Safety notes
1
WARNING
Correct handling of the devices
When operating electrical devices, it is inevitable that certain components will carry
dangerous voltages.
Therefore, failure to handle the units properly can result in death or serious physical injury
as well as extensive property damage.
Only appropriately qualified personnel may work on or in the vicinity of this equipment.
Perfect, safe, and reliable operation of this equipment is dependent on proper
transportation, storage, installation and mounting.
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again.
If this instruction is not observed, touching live parts can result in death or serious injury.
Safety notes
SITOP PSU300M/300B
8 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 9
Description, device design, dimension drawing
2
2.1
Device description
SITOP PSU300M/300B is a primary-clocked power supply for connection to a 3-phase AC
line supply. An electronically regulated DC voltage that can be set via a potentiometer is
available at the output of the device. The output of the device is isolated, no-load proof and
short-circuit proof. The LED displays indicate the operating state. The operating state of the
device can be processed via the signaling contact. The PSU300B devices are optimized to
charge batteries.
Line input
DC output
Signaling contacts
Potentiometer 12 ... 14 V, 24 ... 28.8 V, 42 ... 56 V
Pilot lamps (12/24/48 V OK, OVERLOAD, SHUT DOWN)
Selector switch
DIN rail slider
Convection
Clearance above/below
Figure 2-1 Design
Description, device design, dimension drawing
2.2 Connections and terminal designation
SITOP PSU300M/300B
10 Manual, 11.2014, C98130-A7574-A2-2-7629
2.2
Connections and terminal designation
The line input terminals can be used to establish the connection to the supply voltage.
The output terminals are used to connect to the loads to be supplied (see also Section
Installation (Page 35)).
Connections and terminal designations
Line input L1, L2, L3, PE One screw terminal each
output "+" 2 screw terminals
output "–" 2 screw terminals
signaling contacts 13, 14 One screw terminal each
*1)
Do not subject the end stop to higher loads
Figure 2-2 Terminal data for 6EP1436-3BA10, 6EP1456-3BA00, 6EP1424-3BA00, 6EP1436-3BA20
*1)
Do not subject the end stop to higher loads
Figure 2-3 Terminal data for 6EP1437-3BA20
Description, device design, dimension drawing
2.3 Potentiometer
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 11
2.3
Potentiometer
The potentiometer on the front of the device is used to adjust the output voltage. The
output voltage is set to 12 V, 24 V or 48 V in the factory, and can be adjusted in the range
12 ... 14 V, 24 ... 28.8 V or 42 ... 56 V; for example, to compensate voltage drops across long
supply lines to the connected load.
Figure 2-4 Potentiometer (example 6EP1456-3BA00 / 6EP1437-3BA20)
NOTICE
Thermal overload possible
When adjusting the output voltage to >24 V (>48 V), the output current must be derated by
4 %/V or the permissible ambient temperature must be taken into account with 3 K/V
(applies to PSU300M devices).
Note
It is only permissible to use an insulated screwdriver when actuating the potentiometer.
For notes on actuating the potentiometer (screwdriver, torque), see Figure 2-2 Terminal data
for 6EP1436-3BA10, 6EP1456-3BA00, 6EP1424-3BA00, 6EP1436-3BA20 (Page 10) and
Figure 2-3 Terminal data for 6EP1437-3BA20 (Page 10).
Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU300M/300B
12 Manual, 11.2014, C98130-A7574-A2-2-7629
2.4
Status displays and signaling
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V/10 A)
Operating display LED green for "24 V O.K."
Yellow LED for "overload"
Red LED for "latching shutdown"
LED green for "48 V O.K."
Yellow LED for "overload"
Red LED for "latching shutdown"
Signaling contact Relay contact (NO contact, rating
60 V DC / 0.3 A) for "24 V O.K."
Relay contact (NO contact, rating
60 V DC / 0.3 A) for "48 V O.K."
6EP1424-3BA00 (12 V/20 A)
6EP1436-3BA20 (24 V/17 A)
6EP1437-3BA20 (24 V / 30 A)
Operating display LED green for "12 V O.K."
Yellow LED for "overload"
Red LED for "latching shutdown"
LED green for "24 V O.K."
Yellow LED for "overload"
Red LED for "latching shutdown"
Signaling contact Relay contact (NO contact, rating
60 V DC / 0.3 A) for "12 V O.K."
Relay contact (NO contact, rating
60 V DC / 0.3 A) for "24 V O.K."
Figure 2-5 Operating display and signaling (example 6EP1456-3BA00 / 6EP1437-3BA20)
Signaling
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V/10 A)
Green LED lit
Signaling contact ,
contacts 13-14 closed
Normal operation,
output voltage > 20.5 V
Normal operation, output voltage > 41 V
LED
off
Signaling contact ,
contacts 13-14 open
(quiescent position)
No supply voltage No supply voltage
Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 13
Signaling
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V/10 A)
Yellow LED
lit
Signaling contact ,
contacts 13-14 open
(quiescent position)
Overload, output voltage < 20.5 V
(only in "constant current" mode)
Overload, output voltage < 41 V
(only in "constant current" mode)
Yellow and green LED lights
Signaling contact ,
contacts 13-14 closed
Phase failure, output voltage O.K. Phase failure, output voltage O.K.
Red LED lit
Signaling contact ,
contacts 13-14 open
(quiescent position)
Latching shutdown
(only in "Shutdown" mode)
Latching shutdown
(only in "Shutdown" mode)
Red LED
flashes
Signaling contact ,
contacts 13-14 open
(quiescent position)
Overtemperature → power OFF/ON after
3 min
Overtemperature → power OFF/ON after
3 min
Signaling
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Green LED lit
Signaling contact ,
contacts 13-14 closed
Normal operation
Output voltage > 10.0 V
Normal operation, output
voltage > 20.5 V
Normal operation, output
voltage > 20.5 V
LED
off
Signaling contact ,
contacts 13-14 open
(quiescent position)
No supply voltage No supply voltage No supply voltage
Yellow LED
lit
Signaling contact ,
contacts 13-14 open
(quiescent position)
Overload, output voltage
< 10.0 V (only in "constant
current")
Overload, output voltage
< 20.5 V (only in "constant
current" mode)
Overload, output voltage
< 20.5 V (only in "constant
current" mode)
Yellow and green LED lights
Signaling contact ,
contacts 13-14 open
(quiescent position)
Phase failure, output voltage
O.K.
Phase failure, output voltage
O.K.
-
Description, device design, dimension drawing
2.4 Status displays and signaling
SITOP PSU300M/300B
14 Manual, 11.2014, C98130-A7574-A2-2-7629
Signaling
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Red LED
lit
Signaling contact ,
contacts 13-14 open
(quiescent position)
Latching shutdown (only in
"Shutdown" mode)
Latching shutdown (only in
"Shutdown" mode)
Latching shutdown (only in
"Shutdown" mode)
Red LED flashes
Signaling contact ,
contacts 13-14 closed
Overtemperature → power
OFF/ON after 3 minutes
Overtemperature → power
OFF/ON after 3 minutes
Overtemperature → power
OFF/ON after 3 minutes
Description, device design, dimension drawing
2.5 Change-over switch
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 15
2.5
Change-over switch
Figure 2-6 Selector switch (example 6EP1456-3BA00 / 6EP1437-3BA20)
The two switches A and B are used to influence the output characteristic curve:
Switch
ON
OFF
A
influences the output
characteristic
in the load range
Parallel operation:
'Soft' characteristic curve (see, e.g. Figure 6-8
6EP1436-3BA10 parallel operation output char-
acteristic curve (Page 46)) for the parallel oper-
ation of two or more devices: The output
voltage falls with increasing output current
(namely, also for the overcurrent pulse!).
This means that for full output current the high-
est output voltage can normally no longer be
attained.
Single operation:
Delivery state
'Hard' characteristic curve (see, e.g. Figure 6-3
6EP1436-3BA10 single operation output char-
acteristic curve (Page 44)) for normal operation
(single operation): The output voltage is inde-
pendent of the output current.
B
influences the output
characteristic
in the overload range
Latching shutdown:
If the output current rises above the rated value
and above the current limit, the device reduces
the output voltage (see, e.g. Figure 6-13
6EP1436-3BA10 latching shutdown output
characteristic curve (Page 48)). If the output
voltage falls below (10 V), (20 V), (40 V), the
device shuts down latching, the red LED lights.
This limit voltage of (10 V), (20 V), (40 V) is
independent of the set output voltage. The
'Short-time overload current' feature is not
available in this operating mode. In order to
also be able to charge large capacitances in
this operating mode at the output, non-latching
shutdown is performed during the first ten sec-
onds after power on. During these first 10 s, the
device responds for overload as if the switch is
OFF.
Constant current:
Delivery state
If the output current rises above the rated value
and above the current limit, the device reduces
the output voltage. The yellow LED lights if the
output voltage falls below
(10 V), (20 V), (40 V).
Delivery state: A-OFF; B-OFF
Description, device design, dimension drawing
2.6 Block diagram
SITOP PSU300M/300B
16 Manual, 11.2014, C98130-A7574-A2-2-7629
2.6
Block diagram
Figure 2-7 Block diagram
Description, device design, dimension drawing
2.7 Dimensions and weight
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 17
2.7
Dimensions and weight
Figure 2-8 6EP1424-3BA00, 6EP1436-3BA20, 6EP1436-3BA10, 6EP1456-3BA00 dimensioned
drawing
Figure 2-9 Dimension drawing 6EP1437-3BA20
6EP1424-3BA00 (12 V / 20 A)
6EP1436-3BA20 (24 V / 17 A)
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V / 10 A)
6EP1437-3BA20 (24 V / 30 A)
Dimensions (W × H × D) in mm
70 × 125 × 125
150 × 125 × 150
Weight
approx. 1.2 kg
approx. 3.4 kg
Description, device design, dimension drawing
2.7 Dimensions and weight
SITOP PSU300M/300B
18 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 19
Mounting/disassembly
3
WARNING
Installing the device in a housing or a control cabinet
The SITOP PSU300M/300B power supply is a built-in device. It must be installed in a
housing or control cabinet, to which only qualified personnel have access.
The device can be mounted in a control cabinet on standard mounting rails according to
EN 60715.
Mounting
To mount the device, position it with the mounting rail guide at the upper edge of the
standard mounting rail and press down to lock it into place. If this is too difficult, press slider
at the same time, as described under "Removal".
Removal
To remove, pull up the slider using a screwdriver and disengage the device at the
bottom edge of the standard mounting rail. Then you can remove the device from the upper
edge of the standard mounting rail.
Figure 3-1 Mounting/removal (example 6EP1456-3BA00)
Mounting/disassembly
SITOP PSU300M/300B
20 Manual, 11.2014, C98130-A7574-A2-2-7629
WARNING
Use in hazardous zones
If the devices are to be used in hazardous zones (Ex II 3G Ex nA nC IIC T4) they must be
installed in a distribution box with degree of protection IP54 or higher.
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 21
Mounting position, mounting clearances
4
4.1
Standard mounting position
The device is mounted on standard mounting rails according to EN 60715. The device must
be mounted vertically in such a way that the input terminals and the output terminals are at
the bottom to ensure correct cooling.
A clearance of at least 50 mm should be maintained above and below the device (maximum
depth of the cable duct, 50 mm).
No space is required at the side.
Output current as a function of the ambient temperature and mounting height
Figure 4-1 6EP1436-3BA10: Output current in the standard mounting position
Figure 4-2 6EP1456-3BA00: Output current in the standard mounting position
Mounting position, mounting clearances
4.1 Standard mounting position
SITOP PSU300M/300B
22 Manual, 11.2014, C98130-A7574-A2-2-7629
Figure 4-3 6EP1424-3BA00: Output current in the standard mounting position
Figure 4-4 6EP1436-3BA20: Output current in the standard mounting position
Figure 4-5 6EP1437-3BA20: Output current in the standard mounting position
Mounting position, mounting clearances
4.1 Standard mounting position
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 23
Figure 4-6 Mounting height derating
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
24 Manual, 11.2014, C98130-A7574-A2-2-7629
4.2
Other mounting positions
For mounting positions that deviate from the standard mounting position, derating factors
(reduction of the output power or the permissible ambient temperature) must be observed in
accordance with the following diagrams.
Note
In the case of mounting positions that deviate from the standard mounting position, reduced
mechanical resistance of the devices against vibration and shock must be expected.
Particularly when installing on a vertically fas
tened standard mounting rail, additional
measures may be required, e.g. to prevent the device from slipping on the standard
mounting rail.
4.2.1
6EP1436-3BA10
Figure 4-7 6EP1436-3BA10 mounting position (1)
Figure 4-8 6EP1436-3BA10 mounting position (2)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 25
Figure 4-9 6EP1436-3BA10 mounting position (3)
Figure 4-10 6EP1436-3BA10 mounting position (4)
Figure 4-11 6EP1436-3BA10 mounting position (5)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
26 Manual, 11.2014, C98130-A7574-A2-2-7629
4.2.2
6EP1456-3BA00
Figure 4-12 6EP1456-3BA00 mounting position (1)
Figure 4-13 6EP1456-3BA00 mounting position (2)
Figure 4-14 6EP1456-3BA00 mounting position (3)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 27
Figure 4-15 6EP1456-3BA00 mounting position (4)
Figure 4-16 6EP1456-3BA00 mounting position (5)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
28 Manual, 11.2014, C98130-A7574-A2-2-7629
4.2.3
6EP1424-3BA00
Figure 4-17 6EP1424-3BA00 mounting position (1)
Figure 4-18 6EP1424-3BA00 mounting position (2)
Figure 4-19 6EP1424-3BA00 mounting position (3)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 29
Figure 4-20 6EP1424-3BA00 mounting position (4)
Figure 4-21 6EP1424-3BA00 mounting position (5)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
30 Manual, 11.2014, C98130-A7574-A2-2-7629
4.2.4
6EP1436-3BA20
Figure 4-22 6EP1436-3BA20 mounting position (1)
Figure 4-23 6EP1436-3BA20 mounting position (2)
Figure 4-24 6EP1436-3BA20 mounting position (3)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 31
Figure 4-25 6EP1436-3BA20 mounting position (4)
Figure 4-26 6EP1436-3BA20 mounting position (5)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
32 Manual, 11.2014, C98130-A7574-A2-2-7629
4.2.5
6EP1437-3BA20
Figure 4-27 6EP1437-3BA20 mounting position (1)
Figure 4-28 6EP1437-3BA20 mounting position (2)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 33
Figure 4-29 6EP1437-3BA20 mounting position (3)
Figure 4-30 6EP1437-3BA20 mounting position (4)
Figure 4-31 6EP1437-3BA20 mounting position (5)
Mounting position, mounting clearances
4.2 Other mounting positions
SITOP PSU300M/300B
34 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 35
Installation
5
WARNING
Hazard due to electric shock
Before installation or maintenance work can begin, the system's main switch must be
switched off and measures taken to prevent it being switched on again. If this instruction is
not observed, touching live parts can result in death or serious injury.
5.1
Line-side connection
The SITOP PSU300M/300B power supply is designed for connection to a 3-phase AC line
supply (TN or TT system according to VDE 0100 T 300/IEC 364-3) with a rated voltage of
3-phase 400-500 V AC, 50/-60 Hz, IT system with rated voltages 3-phase 400-480 V AC.
Figure 5-1 Line connection (example: 6EP1456-3BA00)
The line supply is connected using terminals L1, L2, L3 and PE (see Figure 5-1 Line
connection (example: 6EP1456-3BA00) (Page 35)), and must be implemented according to
IEC 60364 and EN 50178 . A protective device (miniature circuit breaker or circuit breaker)
and a disconnection unit for the power supply must be provided. A ground-fault circuit
interrupter is not permissible against indirect contact as the only protective measure. This
applies for the complete line supply protected by the ground-fault circuit interrupter.
Installation
5.1 Line-side connection
SITOP PSU300M/300B
36 Manual, 11.2014, C98130-A7574-A2-2-7629
Protection
SITOP PSU300M/300B
Recommended line-side protection
6EP1436-3BA10
(24 V / 20 A)
3-pole coupled miniature circuit breaker (IEC 898), characteristic C, 6-16 A or
3RV2011-1EA10 circuit breaker, setting of the thermal overcurrent trip: 3 A
or 3RV2711-1DD10 circuit breaker (branch circuit protection according to UL 489)
6EP1456-3BA00
(48 V / 10 A)
3-pole coupled miniature circuit breaker (IEC 898), characteristic C, 6-16 A or
3RV2011-1EA10 circuit breaker, setting of the thermal overcurrent trip: 3 A
or 3RV2711-1DD10 circuit breaker (branch circuit protection according to UL 489)
6EP1424-3BA00
(12 V / 20 A)
3-pole coupled miniature circuit breaker (IEC 898), characteristic C, 6-10 A or
3RV2011-1EA10 circuit breaker, setting of the thermal overcurrent trip: 3 A
or 3RV2711-1DD10 circuit breaker (branch circuit protection according to UL 489)
6EP1436-3BA20
(24 V / 17 A)
3-pole coupled miniature circuit breaker (IEC 898), characteristic C, 6-16 A or
3RV2011-1EA10 circuit breaker, setting of the thermal overcurrent trip: 3 A
or 3RV2711-1DD10 circuit breaker (branch circuit protection according to UL 489)
6EP1437-3BA20
(24 V / 30 A)
3-pole coupled miniature circuit breaker (IEC 898), characteristic C, 10-16 A or
3RV2011-1EA10 circuit breaker, setting of the thermal overcurrent trip: 3 A
or 3RV2711-1DD10 circuit breaker (branch circuit protection according to UL 489)
The protective conductor of the line supply must be connected at the PE terminal.
Other country-specific regulations may have to be observed when installing the device.
Installation
5.2 Output-side connection
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 37
5.2
Output-side connection
At its output, the SITOP PSU300M/300B power supply provides an isolated (= non-
grounded) SELV output voltage (Safety Extra Low Voltage). The output of the power supply
is no-load, overload, and short-circuit proof. If an overload occurs, the electronic current
limiting function limits the output current to a maximum value (see Section Technical data
(Page 39)).
Figure 5-2 Output connection (example 6EP1456-3BA00 / 6EP1437-3BA20)
The output voltage is connected via the + and - terminals at the output of the power supply
(see Figure 5-2 Output connection (example 6EP1456-3BA00 / 6EP1437-3BA20)
(Page 37)). Ensure that the output cables are dimensioned correctly for the maximum output
current rms value and fused accordingly.
Note
If the safety concept of the plant or system specifies that the DC output circuit should be
grounded (PELV), then it is permissible that the output voltage of the SITOP power s
upply is
grounded. In this case, ideally, the grounding at the output should be directly connected from
terminal "
-" of the power supply to a suitable connection point of the protective conductor
system (PE) of the plant or system.
Installation
5.2 Output-side connection
SITOP PSU300M/300B
38 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 39
Technical data
6
Note
Technical data is applicable for a rated input voltage, rated load and +25° C ambient
temperature (if nothing else is specified).
6.1
Input
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V / 10 A)
Input
3-phase, AC
3-phase, AC
Rated voltage value Ue rated
400-500 V
400-500 V
Voltage range
Remark
320 ... 575 V
Derating at Ue < 340 V: 10% [Ia]
320 ... 575 V
No derating
Wide-range input
Yes
Yes
Overvoltage strength
2.3 × Ue rated, 1.3 ms
2.3 × Ue rated, 1.3 ms
Power failure buffering at Ia rated, min
Remark: at Ue = 400 V
15 ms
15 ms
Rated line frequency
50-60 Hz
50-60 Hz
Line frequency range
47 ... 63 Hz
47 ... 63 Hz
Input current / at rated value of input
voltage 400 V
1.2 A 1.2 A
Input current / at rated value of input
voltage 500 V
1 A
1 A
Inrush current limiting
(+25° C), max.
18 A
18 A
I²t, max
0.8 A
2
s
0.8 A
2
s
Integrated input fuse
None
None
Protection in the line feeder cable
(IEC 898)
Required: 3-pole, coupled miniature circuit breaker 6 ... 16 A characteristic C
or circuit breaker 3RV2011-1DA10 (setting 3 A) or 3RV2711-1DD10 (UL 489)
Technical data
6.1 Input
SITOP PSU300M/300B
40 Manual, 11.2014, C98130-A7574-A2-2-7629
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Input 3-phase, AC 3-phase, AC 3-phase, AC
Rated voltage value Ue rated 400-500 V 400-500 V 400-500 V
Voltage range
320 ... 575 V
320 ... 575 V
320 ... 575 V
Wide-range input Yes Yes Yes
Overvoltage strength
2.3 × Ue rated, 1.3 ms
2.3 × Ue rated, 1.3 ms
2.3 × Ue rated, 1.3 ms
Power failure buffering
at Ia rated, min
Remark: at Ue = 400 V
20 ms 20 ms 20 ms
Rated line frequency
50-60 Hz
50-60 Hz
50-60 Hz
Line frequency range
47 ... 63 Hz
47 ... 63 Hz
47 ... 63 Hz
Input current / at rated value of
input voltage 400 V
0.7 A 1.2 A 1.6 A
Input current / at rated value of
input voltage 500 V
0.6 A 1 A 1.3 A
Inrush current limiting
(+25° C), max.
18 A 18 A 56 A
I²t, max
0.8 A
2
s
0.8 A
2
s
2.24 A
2
s
Integrated input fuse
None
None
None
Protection in the line feeder
cable (IEC 898)
Required: 3-pole, coupled miniature circuit breaker 6 ...
10 A characteristic C or circuit breaker 3RV2011-1DA10
(setting 3 A) or 3RV2711-1DD10 (UL 489)
Required: 3-pole, coupled
miniature circuit breaker
10 ... 16 A characteristic C
or circuit breaker
3RV2011-1DA10 (setting
3 A) or 3RV2711-
1DD10 (UL 489)
Figure 6-1 Power failure buffering
Technical data
6.2 Output
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 41
6.2
Output
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Output Regulated, isolated DC voltage Regulated, isolated DC voltage
Rated voltage value Ua rated DC 24 V 48 V
Total tolerance, static ±
3 %
3 %
Static line regulation, approx.
0,1 %
0,1 %
Static load regulation, approx. 0,2 % 0,2 %
Residual ripple in the load range
peak-peak, max.
100 mV 100 mV
Spikes peak-peak, max.
(bandwidth, approx. 20 MHz)
200 mV 200 mV
Adjustment range
Remark
24 … 28.8 V
Derating, see Section Potentiometer
(Page 11)
42 … 56 V
Derating, see Section Potentiometer
(Page 11)
Product function / output voltage can
be adjusted
Yes Yes
Output voltage setting
Remark
Via potentiometer
Max. 480 W
Via potentiometer
Max. 480 W
Operating display
LED green for "24 V O.K."
LED green for "48 V O.K."
Signaling Relay contact (NO contact, rating
60 V DC / 0.3 A) for "24 V O.K."
Relay contact (NO contact, rating
60 V DC / 0.3 A) for "48 V O.K."
Response when switching on/off
No overshoot of Ua (Soft-Start)
No overshoot of Ua (Soft-Start)
Starting delay, max.
2.5 s
2.5 s
Voltage rise, typ.
150 ms
150 ms
Voltage rise time of the output voltage,
maximum
500 ms 500 ms
Rated current value Ia rated
20 A
10 A
Current range
Remark
0 … 20 A
14 A to +70° C
0 … 10 A
7 A to +70° C
Output active power / typical
480 W
480 W
Constant overload current / for a short
circuit when powering up / typical
23 A 11 A
Short-time overload current / for a short
circuit during operation, typical
60 A 23 A
Duration of the current overload capa-
bility / for a short circuit during opera-
tion
25 ms 25 ms
Can be connected in parallel to
increase the power rating
Remark
Yes
Switchable characteristic curve (see
Figure 2-6 Selector switch (example
6EP1456-3BA00 / 6EP1437-3BA20)
(Page 15))
Yes
Switchable characteristic curve (see
Figure 2-6 Selector switch (example
6EP1456-3BA00 / 6EP1437-3BA20)
(Page 15))
Technical data
6.2 Output
SITOP PSU300M/300B
42 Manual, 11.2014, C98130-A7574-A2-2-7629
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Number of units connected in parallel
to increase the power rating, units
2 2
Output characteristic See Figure 6-3 6EP1436-3BA10 single
operation output characteristic curve
(Page 44)
See Figure 6-4 6EP1456-3BA00 single
operation output characteristic curve
(Page 44)
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Output Regulated, isolated DC
voltage
Regulated, isolated DC
voltage
Regulated, isolated DC
voltage
Rated voltage value Ua rated
DC
12 V 24 V 24 V
Total tolerance, static ±
3 %
3 %
3 %
Static line regulation, approx.
2 %
0,1 %
0,1 %
Static load regulation,
approx.
4 % 0,2 % 0,1 %
Residual ripple in the load
range peak-peak, max.
100 mV 100 mV 100 mV
Spikes peak-peak, max.
(bandwidth, approx. 20 MHz)
200 mV 200 mV 200 mV
Adjustment range
12 ... 14 V
24 … 28.8 V
24 … 28.8 V
Product function / output
voltage can be adjusted
Yes Yes Yes
Output voltage setting
Remark
Via potentiometer
-
Via potentiometer
Max. 480 W
Via potentiometer
-
Operating display
LED green for "12 V O.K."
LED green for "24 V O.K."
LED green for "24 V O.K."
Signaling Relay contact (NO contact,
rating 60 V DC / 0.3 A) for
"12 V O.K."
Relay contact (NO contact, rating 60 V DC / 0.3 A) for
"24 V O.K."
Response when switching
on/off
No overshoot of Ua
(Soft-Start)
No overshoot of Ua
(Soft-Start)
No overshoot of Ua
(Soft-Start)
Starting delay, max.
2.5 s
2.5 s
2.5 s
Voltage rise, typ.
20 ms
40 ms
20 ms
Voltage rise time of the
output voltage, maximum
500 ms 500 ms 500 ms
Rated current value Ia rated
20 A
20 A
30 A
Current range
Remark
0 … 20 A
20 A to +70° C
0 … 17 A
14 A to +70 °C
0 … 30 A
25 A to +70° C
Output active power /
typical
240 W 408 W 720 W
Constant overload current
for a short-circuit when
powering up, typical
22 A 19 A 32 A
Technical data
6.2 Output
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 43
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Short-time overload current
for a short-circuit during
operation, typical
60 A - -
Duration of the current
overload capability for a
short-circuit during operation
25 ms
-
-
Can be connected in parallel
to increase the power rating
Remark
Yes
Switchable characteristic
curve (see Figure 2-6 Selec-
tor switch (example
6EP1456-3BA00 / 6EP1437-
3BA20) (Page 15))
Yes
Switchable characteristic
curve (see Figure 2-6 Selec-
tor switch (example
6EP1456-3BA00 / 6EP1437-
3BA20) (Page 15))
Yes
Switchable characteristic
curve (see Figure 2-6 Selec-
tor switch (example
6EP1456-3BA00 / 6EP1437-
3BA20) (Page 15))
Number of devices that can
be connected in parallel to
increase the power rating,
units
2 2 2
Output characteristic See Figure 6-5 6EP1424-
3BA00 single operation out-
put characteristic curve
(Page 44)
See Figure 6-6 6EP1436-
3BA20 single operation out-
put characteristic curve
(Page 45)
See Figure 6-7 6EP1437-
3BA20 single operation out-
put characteristic curve
(Page 45)
Figure 6-2 Starting delay/voltage rise
Technical data
6.2 Output
SITOP PSU300M/300B
44 Manual, 11.2014, C98130-A7574-A2-2-7629
Figure 6-3 6EP1436-3BA10 single operation output characteristic curve
Figure 6-4 6EP1456-3BA00 single operation output characteristic curve
Figure 6-5 6EP1424-3BA00 single operation output characteristic curve
Technical data
6.2 Output
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 45
Figure 6-6 6EP1436-3BA20 single operation output characteristic curve
Figure 6-7 6EP1437-3BA20 single operation output characteristic curve
The device supplies a constant output voltage until the current limit is reached.
If overload occurs, the output current is limited and the output voltage lowered.
Technical data
6.2 Output
SITOP PSU300M/300B
46 Manual, 11.2014, C98130-A7574-A2-2-7629
Selector switch A closed (parallel operation):
The output voltage decreases with increasing output current.
Figure 6-8 6EP1436-3BA10 parallel operation output characteristic curve
Figure 6-9 6EP1456-3BA00 parallel operation output characteristic curve
Figure 6-10 6EP1424-3BA00 parallel operation output characteristic curve
Technical data
6.2 Output
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 47
Figure 6-11 6EP1436-3BA20 parallel operation output characteristic curve
Figure 6-12 6EP1437-3BA20 parallel operation output characteristic curve
Technical data
6.2 Output
SITOP PSU300M/300B
48 Manual, 11.2014, C98130-A7574-A2-2-7629
Selector switch B closed (latching shutdown):
The device will be shut down if the overload continues for longer than 100 ms.
A reset is performed by switching the power supply OFF for at least 5 seconds.
Figure 6-13 6EP1436-3BA10 latching shutdown output characteristic curve
Figure 6-14 6EP1456-3BA00 latching shutdown output characteristic curve
Figure 6-15 6EP1424-3BA00 latching shutdown output characteristic curve
Technical data
6.2 Output
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 49
Figure 6-16 6EP1436-3BA20 latching shutdown output characteristic curve
Figure 6-17 6EP1437-3BA20 latching shutdown output characteristic curve
Technical data
6.3 Efficiency
SITOP PSU300M/300B
50 Manual, 11.2014, C98130-A7574-A2-2-7629
6.3
Efficiency
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Efficiency at Ua rated, Ia rated, approx. 93 % 93 %
Power loss at Ua rated, Ia rated, approx. 36 W 36 W
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Efficiency at Ua rated, Ia
rated, approx.
88 % 93 % 93 %
Power loss at Ua rated, Ia
rated, approx.
20 W 31 W 50 W
Figure 6-18 6EP1436-3BA10 efficiency
Technical data
6.3 Efficiency
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 51
Figure 6-19 6EP1456-3BA00 efficiency
Figure 6-20 6EP1424-3BA00 efficiency
Technical data
6.3 Efficiency
SITOP PSU300M/300B
52 Manual, 11.2014, C98130-A7574-A2-2-7629
Figure 6-21 6EP1436-3BA20 efficiency
Figure 6-22 6EP1437-3BA20 efficiency
Technical data
6.4 Closed-loop control
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 53
6.4
Closed-loop control
6EP1436-3BA10 (24 V/20 A)
6EP1456-1BA00 (48 V/10 A)
Dyn. line regulation
(Ue rated ±15 %), max.
1 % 1 %
Dyn. load regulation
(Ia: 50/100/50%), Ua ± typ.
2 % 2 %
Load step regulation time
50 to 100 %, typ.
2 ms 2 ms
Load step regulation time
100 to 50 %, typ.
2 ms 2 ms
Regulation time / maximum
10 ms
10 ms
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Dyn. line regulation
(Ue rated ±15 %), max.
2 % 1 % 1 %
Dyn. load regulation
(Ia: 50/100/50%), Ua ± typ.
4 % 2 % 3 %
Load step regulation time
50 to 100 %, typ.
2 ms 2 ms -
Load step regulation time
100 to 50 %, typ.
2 ms 2 ms -
Regulation time / maximum
10 ms
10 ms
10 ms
Technical data
6.5 Protection and monitoring
SITOP PSU300M/300B
54 Manual, 11.2014, C98130-A7574-A2-2-7629
6.5
Protection and monitoring
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Output overvoltage protection < 35 V Yes, according to EN 60950
Current limitation, typ. 23 A 11 A
Property of the output / short-circuit
proof
Yes Yes
Short-circuit protection Optional constant current characteristic
approx. 23 A or "latching shutdown"
Optional constant current characteristic
approx. 11 A or "latching shutdown"
Continuous short-circuit current /
rms value / typical
Remark
23 A
Overload capability 150% Ia rated up to
5 s/min
11 A
Overload capability 150% Ia rated up to
5 s/min
Overload/short-circuit indicator Yellow LED for "overload", red LED for
"latching shutdown"
Yellow LED for "overload", red LED for
"latching shutdown"
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Output overvoltage protec-
tion
< 35 V < 35 V < 35 V
Current limitation, typ.
22 A
19 A
32 A
Property of the output /
short-circuit proof
Yes Yes Yes
Short-circuit protection Optional constant current
characteristic approx. 22 A
or "latching shutdown"
Optional constant current
characteristic approx. 19 A
or "latching shutdown"
Optional constant current
characteristic approx. 32 A
or "latching shutdown"
Continuous short-circuit
current / rms value / typical
Remark
22 A
Overload capability 150%
Ia rated
up to 5 s/min
19 A
-
32 A
-
Overload / short-circuit dis-
play
Yellow LED for "overload",
red LED for "latching shut-
down"
Yellow LED for "overload",
red LED for "latching shut-
down"
Yellow LED for "overload",
red LED for "latching shut-
down"
Technical data
6.6 MTBF
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 55
6.6
MTBF
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
6EP1424-3BA00 (12 V/20 A)
6EP1436-3BA20 (24 V/17 A)
6EP1437-3BA20 (24 V / 30 A)
Mean Time Between Failures SN29500: > 500,000 hours (typ. 700,000 hours) at 40 °C, rated load, 24-hour opera-
tion
6.7
Mechanical system
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Connection system
Screw-type terminal
Screw-type terminal
Connections / line supply L1, L2, L3, PE: 1 screw terminal each
for 0.2 ... 6 (4) mm²
solid (finely stranded)
L1, L2, L3, PE: 1 screw terminal each
for 0.2 ... 6 (4) mm²
solid (finely stranded)
Connections / output +, -: 2 screw terminals each for
0.2 ... 6 (4) mm² solid (finely stranded)
+, -: 2 screw terminals each for
0.2 ... 6 (4) mm² solid (finely stranded)
Connections / auxiliary contacts 13, 14 (signaling contact): 1 screw
terminal each for 0.14 ... 1.5 mm²
solid (finely stranded)
13, 14 (signaling contact): 1 screw
terminal each for 0.14 ... 1.5 mm²
solid (finely stranded)
Width of the housing
70 mm
70 mm
Height of the housing
125 mm
125 mm
Depth of the housing
125 mm
125 mm
Mounting width
70 mm
70 mm
Mounting height
225 mm
225 mm
Weight, approx.
1.2 kg
1.2 kg
Product feature of the housing /
housing that can be lined up next to
one another
Yes Yes
Type of mounting / panel mounting No No
Type of mounting / rail mounting Yes Yes
Type of mounting / S7-300 rail mount-
ing
No No
Mounting Can be snapped onto standard
EN 60715 35x7,5/15 mounting rails
Can be snapped onto standard
EN 60715 35x7,5/15 mounting rails
Technical data
6.7 Mechanical system
SITOP PSU300M/300B
56 Manual, 11.2014, C98130-A7574-A2-2-7629
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Connection system Screw-type terminal Screw-type terminal Screw-type terminal
Connections / line supply L1, L2, L3, PE:
1 screw terminal each for
0.2 ... 6 (4) mm²
solid (finely stranded)
L1, L2, L3, PE:
1 screw terminal each for
0.2 ... 6 (4) mm²
solid (finely stranded)
L1, L2, L3, PE:
1 screw terminal each for
0.2 ... 6 (4) mm²
solid (finely stranded)
Connections / output +, -: 2 screw terminals each
for 0.2 ... 6 (4) mm²
solid (finely stranded)
+, -: 2 screw terminals each
for 0.2 ... 6 (4) mm²
solid (finely stranded)
+, -: 2 screw terminals each
for 0.5 ... 16 (10) mm²
solid (finely stranded)
Connections/auxiliary con-
tacts 13, 14 (signaling con-
tact)
1 screw terminal each for
0.14 ... 1.5 mm²
solid (finely stranded)
1 screw terminal each for
0.14 ... 1.5 mm²
solid (finely stranded)
1 screw terminal each for
0.14 ... 4 (2.5) mm²
solid (finely stranded)
Width of the housing
70 mm
70 mm
150 mm
Height of the housing
125 mm
125 mm
125 mm
Depth of the housing
125 mm
125 mm
150 mm
Mounting width
70 mm
70 mm
150 mm
Mounting height
225 mm
225 mm
225 mm
Weight, approx.
1.2 kg
1.2 kg
3.4 kg
Product feature of the hous-
ing / housing that can be
lined up next to one another
Yes Yes Yes
Type of mounting / panel
mounting
No No No
Type of mounting / rail
mounting
Yes Yes Yes
Type of mounting / S7-300
rail mounting
No No No
Mounting Can be snapped onto standard EN 60715 35x7,5/15 mount-
ing rails
Can be snapped onto stand-
ard EN 60715 35x15 mount-
ing rails
Technical data
6.8 Accessories
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 57
6.8
Accessories
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Electrical accessories Buffer module, redundancy module -
Mechanical accessories Device identification labels 20 mm × 7 mm, pastel turquoise 3RT1900-1SB20
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Electrical accessories - Buffer module, redundancy
module
Buffer module, redundancy
module
Mechanical accessories
Device identification labels 20 mm × 7 mm, pastel turquoise 3RT1900-1SB20
6.9
Dimension drawing
See Section Dimensions and weight (Page 17)
CAD data that can be downloaded from the Internet:
6EP1436-3BA10
(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00459)
6EP1456-3BA00
(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00568)
6EP1424-3BA00
(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00680)
6EP1436-3BA20
(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00724)
6EP1437-3BA20
(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00683)
Technical data
6.9 Dimension drawing
SITOP PSU300M/300B
58 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 59
Safety, approvals, EMC
7
7.1
Safety
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
Primary/secondary galvanic isolation
Yes
Yes
Electrical isolation SELV output voltage Ua according to
EN 60950-1 and EN 50178
SELV output voltage Ua according to
EN 60950-1 and EN 50178
Protection class
Class I
Class I
Degree of protection (EN 60529)
IP 20
IP 20
Leakage current, typ.
0.9 mA
0.9 mA
Leakage current, max.
3.5 mA
3.5 mA
Test voltage
See Table 7-1 Test voltage (Page 60)
See Table 7-1 Test voltage (Page 60)
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
Primary/secondary galvanic isolation
Yes
Yes
Yes
Electrical isolation SELV output voltage Ua
according to EN 60950-1
and EN 50178
SELV output voltage Ua
according to EN 60950-1
and EN 50178
SELV output voltage Ua
according to EN 60950-1
and EN 50178
Protection class
Class I
Class I
Class I
Degree of protection (EN 60529)
IP20
IP20
IP20
Leakage current, typ.
0.9 mA
0.9 mA
0.4 mA
Leakage current, max.
3.5 mA
3.5 mA
3.5 mA
Test voltage See Table 7-1 Test
voltage (Page 60)
See Table 7-1 Test
voltage (Page 60)
See Table 7-1 Test
voltage (Page 60)
Safety, approvals, EMC
7.2 Test voltage
SITOP PSU300M/300B
60 Manual, 11.2014, C98130-A7574-A2-2-7629
7.2
Test voltage
Figure 7-1 Test voltage without auxiliary contact diagram
Only the manufacturer can perform the type test and production test; users can also perform
the field test.
Preconditions for performing the field test:
Tests (A) & (B)
Connect the input terminals with one another
Connect the output terminals and PE together
Test (C)
Connect the output terminals with one another and measure with respect to PE
Table 7- 1 Test voltage
Test time
Prim ↔ sec (A)
Prim ↔ PE (B)
Sec ↔ PE (C)
Type test 60 s 4200 VDC 2200 VDC 700 VDC
60 s
3000 VAC
1500 VAC
500 VAC
Production test 1 s 2200 VDC 2200 VDC 500 VDC
1 s
1500 VAC
1500 VAC
350 VAC
Field test
1 s
2200 VDC
2200 VDC
500 VDC
1 s
1500 VAC
1500 VAC
350 VAC
Remark:
Tripping current for DC measurement: 0
mA
Tripping current for AC measurement: < 100 mA
Safety, approvals, EMC
7.3 Approvals
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 61
7.3
Approvals
6EP1436-3BA10 (24 V/20 A)
6EP1456-3BA00 (48 V/10 A)
CE marking Yes, (2004/108/EG and 2006/95/EG) Yes, (2004/108/EG and 2006/95/EG)
UL/cUL (CSA) approval cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259
cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
Explosion protection EPS 12 ATEX 1 442 X
IECEx EPS 14.0062X
II 3G Ex nA nC IIC T4 Gc
cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01-2007)
CB approval
Yes
Yes
SEMI F47 compliance
Fulfilled
-
Marine approvals
GL, ABS
GL, ABS
6EP1424-3BA00
(12 V / 20 A)
6EP1436-3BA20
(24 V / 17 A)
6EP1437-3BA20
(24 V / 30 A)
CE marking Yes, (2004/108/EG and
2006/95/EG)
Yes, (2004/108/EG and
2006/95/EG)
Yes, (2004/108/EG and
2006/95/EG)
UL/cUL (CSA) approval cULus-Listed (UL 508,
CSA C22.2 No. 107.1),
File E197259
cULus-Listed (UL 508,
CSA C22.2 No. 107.1),
File E197259
cULus-Listed (UL 508,
CSA C22.2 No. 107.1),
File E197259
Marine approvals
-
GL
-
7.4
EMC
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V / 10 A)
6EP1424-3BA00 (12 V / 20 A)
6EP1436-3BA20 (24 V / 17 A)
6EP1437-3BA20 (24 V / 30 A)
Electrostatic discharge
EN 61000-4-2
8 kV contact, 8 kV air
Electromagnetic fields
EN 61000-4-3
80 … 1000 MHz 25 V/m 1000 … 2700 MHz 10 V/m
High-speed transient dis-
turbances (burst)
EN 61000-4-4 4 kV at line supply connections, 2 kV at the DC output
Surge voltages EN 61000-4-5 3 kV symmetrical at the line connections
6 kV unsymmetrical at the line connections
500 V symmetrical/unsymmetrical at DC output cables
High-frequency fields
EN 61000-4-6
10 V; 0.15 … 80 MHz
Magnetic fields
EN 61000-4-8
30 A/m; 50 Hz
Emitted interference
EN 55022
Class B
Safety, approvals, EMC
7.4 EMC
SITOP PSU300M/300B
62 Manual, 11.2014, C98130-A7574-A2-2-7629
6EP1436-3BA10 (24 V / 20 A)
6EP1456-3BA00 (48 V / 10 A)
6EP1424-3BA00 (12 V / 20 A)
6EP1436-3BA20 (24 V / 17 A)
6EP1437-3BA20 (24 V / 30 A)
Line harmonics limit EN 61000-3-2 Class A
Generic standards EN61000-6-2 Noise immunity for industrial environments
EN61000-6-3
Emission for residential areas
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 63
Ambient conditions
8
6EP1436-3BA10 (24 V/20 A)
6EP1424-3BA00 (12 V/20 A)
6EP1436-3BA20 (24 V/17 A)
6EP1437-3BA20 (24 V/30 A)
6EP1456-3BA00 (48 V/10 A)
Ambient temperature -25°...+70° C with natural convection
-10 ...+70° C with natural convection
Tested according to:
EN 60068-2-1 cold
EN 60068-2-2 dry heat
EN 60068-2-78 humid heat, constant
EN 60068-2-14 temperature change
Transport and storage temperature -40 ...+85 °C
Tests (packed for shipping) according to:
EN 60068-2-1 cold
EN 60068-2-2 dry heat
EN 60068-2-30 humid heat, cyclic
Humidity class
Climatic class 3K3 according to EN 60721, without condensation
Mechanical stressing
during operation
Tested according to:
EN 60068-2-6 vibration, test Fc:
0.075 mm deflection in the range 10 ... 58 Hz
1 g acceleration in the range 58 ... 150 Hz
EN 60068-2-27 shock, test Ea: Acceleration 150 m/s2, test duration 11 ms
Ambient conditions
SITOP PSU300M/300B
64 Manual, 11.2014, C98130-A7574-A2-2-7629
6EP1436-3BA10 (24 V/20 A)
6EP1424-3BA00 (12 V/20 A)
6EP1436-3BA20 (24 V/17 A)
6EP1437-3BA20 (24 V/30 A)
6EP1456-3BA00 (48 V/10 A)
Damaging gases Tested according to:
EN 60068-2-42 sulfur dioxide
EN 60068-2-43 hydrogen sulfide
Atmospheric pressure Operation:
1080 ... 795 hPa (-1000 ... +2000 m)
For operation at altitudes of 2000 m up to 6000 m above sea level:
output must be derated by -7.5 % / 1000 m or
the ambient temperature must be reduced by 5 K / 1000 m (see Figure 4-6
Mounting height derating (Page 23))
Overvoltage category:
III to 2000 m (EN 50178)
II from 2000 m to 6000 m (EN 50178)
II to 2000 m (EN 60950-1)
I from 2000 m to 6000 m (EN 60950-1)
Storage:
1080 ... 660 hPa (-1000 ...+3500 m)
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 65
Applications
9
9.1
Parallel connection to increase power rating
To increase the power rating, SITOP PSU300M/300B power supplies of the same type can
be directly connected in parallel.
The following must be observed:
The cables connected to each power supply at terminals "+" and "-" must have identical
lengths and the same cable cross-sections (or the same impedance) up to a common
external connection point (terminal strip) if possible.
The power supplies connected in parallel must be switched on simultaneously with a
common switch in the line feeder cable (e.g. with the main switch available in control
cabinets).
The output voltages measured in no-load operation for the power supplies that are not yet
connected in parallel should not deviate more than a maximum of 50 mV. This usually
corresponds to the factory setting. If the output voltage is changed, you should connect
the "-" terminals and then, in no-load operation, measure the voltage difference between
the "+" terminals that have not yet been connected. The voltage difference should not
exceed 50 mV.
Place selector switch A at "ON" (see Section Change-over switch (Page 15))
Figure 9-1 Parallel connection, correct and incorrect
Applications
9.1 Parallel connection to increase power rating
SITOP PSU300M/300B
66 Manual, 11.2014, C98130-A7574-A2-2-7629
NOTICE
Protective circuit for the parallel connection of more than two power supplies
When connecting more than two power supplies in parallel, additional measures must be
taken to prevent high backward feeding currents in the event of a secondary device
fault. For this purpose, a suitable protective circuit (e.g. decoupling diode or DC-conform
circuit breaker) must be installed between each "+" terminal of the power supply and the
common connection point.
Applications
9.2 Parallel connection for redundancy
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 67
9.2
Parallel connection for redundancy
Connecting several SITOP PSU300M/300B power supplies in parallel for redundancy
purposes is required if especially high demands are placed regarding the availability of a
reliable 24 V power supply.
Using the SITOP PSE202U redundancy module, two 24 V power supplies of the same type
up to 20 A can be decoupled (Figure 9-2 Redundant configuration with two power supplies
and one SITOP PSE202U redundancy module (Page 67)). When one of the devices fails,
then the other automatically takes over the power supply. If one of the power supplies fails,
then this is signaled using an LED on the redundancy module as well as an isolated relay
contact.
For higher output current, each power supply must be connected to a redundancy module
(Figure 9-3 Redundant configuration with two power supplies and two SITOP PSE202U
redundancy modules (Page 68)).
When dimensioning the system, it must be ensured that n+1 redundant connected power
supplies can handle the total power requirement of the remaining n power supplies.
Note
For a high reliability of the supply, it is recommended that the redundant switched power
supplies are fused separately on the li
ne-side and, if possible, be connected to different
power supply networks.
Figure 9-2 Redundant configuration with two power supplies and one SITOP PSE202U redundancy
module
Applications
9.2 Parallel connection for redundancy
SITOP PSU300M/300B
68 Manual, 11.2014, C98130-A7574-A2-2-7629
Figure 9-3 Redundant configuration with two power supplies and two SITOP PSE202U redundancy
modules
You can find additional information at:
SITOP PSE202U manual (http://support.automation.siemens.com/WW/view/en/42248598)
Applications
9.3 Series connection for increased voltage
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 69
9.3
Series connection for increased voltage
To achieve an output voltage of 48 V DC, two 24 V SITOP PSU300M/300M power supplies
of the same type can be connected in series. In this case, connect the "-" terminal of the first
power supply to the "+" terminal of the second power supply. The "+" terminal of the first
power supply and the "-" terminal of the second power supply are routed to the load.
Depending on the grounding point of the secondary output voltages, voltages of +48 V,
±24 V or -48 V can be realized.
In the case of an asymmetric load distribution, it is not possible to guarantee correct
functionality.
WARNING
SELV is not guaranteed in the case of a fault
When connecting two power supplies in series, the continuous, permissible SELV voltage
of a maximum of 60 V DC according to EN 60950 cannot be guaranteed in the case of a
fault.
Figure 9-4 Series connection for increased voltage
Applications
9.4 Overload protection in the 24 V output circuit
SITOP PSU300M/300B
70 Manual, 11.2014, C98130-A7574-A2-2-7629
9.4
Overload protection in the 24 V output circuit
If an overload occurs, the electronic current limiting function limits the
SITOP PSU300M/300B output current to a maximum value (see Section Technical data
(Page 39)). The output cables are protected against a thermal overload if they are
dimensioned corresponding to the maximum rms output current, or protected using
additional components (for example, miniature circuit breaker, fuses).
However, a load circuit that fails as a result of overload, for instance, should frequently be
reliably and quickly identified and specifically switched off before the power supply goes into
current-limiting mode (in current-limiting mode, the supply voltage would also be reduced for
all of the remaining 24 V loads).
The SITOP PSE200U selectivity module with 4 outputs (versions with adjustable output
current range for each output from 0.5 ... 3 A and 3 ... 10 A) is available; this monitors the
24 V branches for overload and short circuits (Figure 9-5 Selectivity module (Page 70)). Brief
current peaks, e.g. as a result of a high inrush current, are permitted, and branches with a
longer overload are switched into a no-current condition. This is also ensured for cables in a
high-ohmic condition and for short-circuits that slowly develop over time.
When an output fails, the fault is signaled using a group signal contact or as a single channel
signal, and the branch of the module involved is displayed using an LED.
For variants with single channel signaling, function blocks for evaluation purposes are
available for SIMATIC S7-1200/1500/300/400, for STEP 7 Classic and TIA Portal at no
charge.
You can find additional information at:
SITOP PSE200U selectivity module manuals
(http://support.automation.siemens.com/WW/view/en/10807226/130000)
Figure 9-5 Selectivity module
Applications
9.5 Protection against short-time voltage dips
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 71
9.5
Protection against short-time voltage dips
For a drop in the line-side supply voltage, the SITOP PSU300M/300B power supply still
maintains the output voltage for a short time in the millisecond range (see Chapter Technical
data (Page 39)).
For line supplies that manifest frequent brief voltage dips, in order to increase the power
supply reliability, it may make sense to increase the line buffering time in the device using an
additional SITOP PSE201U buffer module.
The SITOP PSE201U buffer module, based on electrolytic capacitors, is connected in
parallel to the 24 V power supply output (Figure 9-6 Buffer module (Page 71)). The buffer
time is 200 ms at 40 A up to 1.6 s for a load current of 5 A. This time can be increased a
multiple number of times by connecting buffer modules in parallel; the maximum buffer time
is 10 s.
You can find additional information at:
SITOP PSE201U manual (http://support.automation.siemens.com/WW/view/en/41129219)
Figure 9-6 Buffer module
Applications
9.6 Protecting against longer power failures
SITOP PSU300M/300B
72 Manual, 11.2014, C98130-A7574-A2-2-7629
9.6
Protecting against longer power failures
Sudden and longer failures of the line supply voltage can result in undefined states and
significant danger as a result of the associated failure of the plant or system control. The
SITOP power supply product portfolio includes various DC-UPS solutions to prevent the
failure of the 24 V power supply voltage.
Power supply failures up into the minutes range can be buffered using the maintenance-free
SITOP UPS500 DC-UPS modules based on capacitors (Figure 9-7 24 V buffering to allow
the saving of process data and controlled shutdown of PCs (Page 72)).
Figure 9-7 24 V buffering to allow the saving of process data and controlled shutdown of PCs
Using the free-of-charge SITOP DC-UPS software tool, DC-UPS systems can be simply
integrated into PC-based automation solutions. This supports further processing of the status
signals and safely running down the PC.
You can find additional information at:
Manual, DC UPS with capacitors
(http://support.automation.siemens.com/WW/view/en/48932766/133300)
Applications
9.6 Protecting against longer power failures
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 73
Using DC UPS SITOP UPS1600 and SITOP UPS1100 battery modules, buffer times in the
range of hours can be implemented. Intelligent battery management using Energy Storage
Link automatically detects the UPS1100 energy storage device, and ensures optimum
temperature-controlled charging and continuous monitoring. The UPS1600 can be flexibly
integrated into the widest range of automation applications with its digital inputs/outputs as
well as optional USB interface or Ethernet/PROFINET port.
Figure 9-8 24 V buffering with SITOP UPS1600 to maintain communication, signaling functions,
sensor measured values and position values
For open, PC-based automation systems, configuration and monitoring is realized using the
SITOP UPS Manager PC software, which is available at no charge. This allows PC
responses to the operating states of the DC UPS to be freely selected and offers
comprehensive diagnostic functions.
For TIA-based automation systems, the UPS1600 is engineered using the TIA Portal.
Special function blocks for SIMATIC S7-300/400/1200 and S7-1500 available at no charge
make it easy to integrate operating and diagnostics information into STEP 7 user
programs. Preconfigured UPS faceplates for WinCC visualization can be downloaded at no
charge.
You can find additional information at:
DC UPS SITOP UPS1600/UPS1100 Manual
(http://support.automation.siemens.com/WW/view/en/84977415)
Applications
9.7 Battery charging with SITOP PSU300B
SITOP PSU300M/300B
74 Manual, 11.2014, C98130-A7574-A2-2-7629
9.7
Battery charging with SITOP PSU300B
The SITOP PSU300B power supplies are optimized for charging lead accumulators. For a U-
I characteristic curve set to parallel operation (DIP switch "A" at "ON", see Section Figure 2-6
Selector switch (example 6EP1456-3BA00 / 6EP1437-3BA20) (Page 15)), the battery to be
charged is charged with a constant current until approximately 95% of the set SITOP output
voltage is reached (set using a potentiometer, see Section Figure 2-4 Potentiometer
(example 6EP1456-3BA00 / 6EP1437-3BA20) (Page 11)). The charging current then
decreases continuously from 1.2 × rated current at 95% of the set voltage to approx. 0 A or
the self-discharging current of the accumulator at 100% of the set output voltage, i.e. the
resistance characteristic curve in this range (see Figure 6-10 6EP1424-3BA00 parallel
operation output characteristic curve (Page 46), Figure 6-11 6EP1436-3BA20 parallel
operation output characteristic curve (Page 47), Figure 6-12 6EP1437-3BA20 parallel
operation output characteristic curve (Page 47)).
Note
The value recommended by the battery manufacturer (dependent on the accumulator
temperature) must be set as end
-of-charge voltage. A lead accumulator temperature of +20°
to 30° C is ideal; in this
case, the recommended end-of-charge voltage is normally approx.
13.5 or 27
V.
Note
As protection against back e.m.f. and as polarity reversal protection, we recommend that a
suitable diode for at least 1.2 × rated current of the power supply with a
t least 40 V blocking
voltage is connected in series to the "+" output (connect the anode with "+" output of the
SITOP PSU300B and the cathode with the plus pole of the accumulator). The output voltage
of the power supply under no load must be set to the e
nd-of-charge voltage plus the voltage
drop at the diode. For an end
-of-charge voltage of, for example, 27.0
VDC (usual for 20° C to
30° C accumulator temperature, although the specifications of the accumulator manufacturer
must always be observed!) and 0.8
V voltage drop at the diode, the power supply without
load should be set to 27.8
V.
Applications
9.7 Battery charging with SITOP PSU300B
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 75
LEDs and a potential-free signaling contact indicate the associated charge state of the
battery (see Section Figure 2-5 Operating display and signaling (example 6EP1456-
3BA00 / 6EP1437-3BA20) (Page 12)):
Green LED (12 V OK, 24 V OK) lights
Signaling contact 13-14 closed
Battery voltage > approx. 10 V or > approx. 20 V
Yellow LED (overload) lights
Signaling contact 13-14 open
Battery voltage < approx. 10 V or < approx. 20 V
Figure 9-9 Battery charging with SITOP PSU300B
WARNING
The SITOP PSU300B power supply is a built-in device. It must be installed in a housing or
control cabinet, to which only qualified personnel have access.
If SITOP is used as the battery charging device, the VDE 0510 regulations or the
appropriate national regulations must be observed and an adequate ventilation of the
battery location ensured.
Applications
9.7 Battery charging with SITOP PSU300B
SITOP PSU300M/300B
76 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 77
Environment
10
The devices are in conformance with RoHS.
As a rule, only non-silicon precipitating materials are used.
Disposal guidelines
Packaging and packaging aids can and should always be recycled. The product itself may
not be disposed of as domestic refuse.
Environment
SITOP PSU300M/300B
78 Manual, 11.2014, C98130-A7574-A2-2-7629
SITOP PSU300M/300B
Manual, 11.2014, C98130-A7574-A2-2-7629 79
Service & Support
11
Technical support
Technical support for all IA/DT products can be accessed through the following
communication channels:
Phone: + 49 (0) 911 895 7222
E-Mail (mailto:support.automation@siemens.com)
Internet:
Online support request form (http://www.siemens.de/automation/support-request)
Technical documentation on the Internet
Operating instructions and manuals for SITOP are available in the Internet:
Operating instructions/manuals (http://www.siemens.de/sitop/manuals)
SITOP power supply homepage
General news about our power supplies is available in the Internet at the SITOP homepage:
SITOP (http://www.siemens.de/sitop)
Information material
SITOP information can be downloaded from the Internet:
Information and download center (http://www.siemens.de/sitop-infomaterial)
CAx data
2D/3D data and circuit diagram macros can be downloaded from the Internet:
Siemens image database (http://www.siemens.de/sitop-cax)
Request all CAx data via the CAx download manager:
CAx shopping cart (http://www.siemens.de/cax)
SITOP Selection Tool
Simply and quickly select the optimum the power supply or DC-UPS:
SITOP Selection Tool (http://www.siemens.de/sitop-selection-tool)
Online catalog and ordering system
The online catalog and the online ordering system are available through the Industry Mall
homepage:
Industry Mall (http://www.siemens.com/industrymall/de)
Service & Support
SITOP PSU300M/300B
80 Manual, 11.2014, C98130-A7574-A2-2-7629
Contact persons
If you have any questions regarding the use of our products, then contact the Siemens
contact person in your regional Siemens sales office.
You can find these addresses as follows:
On the Internet (http://www.siemens.de/automation/partner)
In Catalog CA 01