INCH-POUND MS3115G 29 April 2009 SUPERSEDING MS3115F 1 March 2007 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, DUMMY STOWAGE, BAYONET COUPLING, FOR MIL-DTL-26482 CONNECTORS, SERIES 1 AND 2 Reactivated after 1 March 2007 and may be used for new and existing designs and acquisitions. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. FIGURE 1. Receptacle, dummy stowage, dimensions and configurations. AMSC N/A FSC 5935 MS3115G A max length side B (TP) centerline-tocenterline mounting holes 8 .828 (21.03) .594 (15.09) 10 .954 (24.23) .719 (18.26) 12 1.047 (26.59) .812 (20.62) 14 1.141 (28.98) .906 (23.01) 16 1.234 (31.34) .969 (24.61) 18 1.328 (33.73) 1.062 (26.97) 20 1.453 (36.91) 1.156 (29.36) 22 1.578 (40.08) 1.250 (31.75) 24 1.703 (43.26) 1.375 (34.93) Shell size F + .031 - .000 mounting flange location G .016 thickness mounting flange .462 (11.73) .062 (1.57) .556 (14.12) H .005 dia mounting holes .120 (3.05) .094 (2.39) .589 (14.96) J + .010 - .020 disk location P min edge distance .328 (8.33) .035 (0.89) .390 (9.91) .050 (1.27) .147 (3.73) Inches mm .005 .010 .015 .016 .020 .031 0.13 0.25 0.38 0.41 0.51 0.79 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3 True position (TP) tolerances specified are in accordance with ASME Y14.5M. 4. Intermateability dimensions shall be in accordance with MIL-DTL-26482. FIGURE 1. Receptacle, dummy stowage, dimensions and configurations - Continued. 2 MS3115G REQUIREMENTS: Dimensions and configuration: See figure 1. Materials: a. Dummy stowage - aluminum alloy. b. Disk material - synthetic rubber or silicone elastomer. Finish: A, D, L, T, W and Z. Finish E is superseded by Finish W. Fluid resistance: This dummy stowage receptacle shall meet the fluid resistance requirements in accordance with MIL-DTL-26482, series 1 and 2. Connector mating: This connector mates with all MIL-DTL-26482, series 1 and 2 connector plugs. Intermateability dimensions shall be in accordance with MIL-DTL-26482. Part or Identifying Number (PIN) example: MS3115 - 12 L MS number Shell size Finish Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: ASME Y14.5M CONCLUDING MATERIAL Preparing activity: DLA - CC Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC (Project 5935-2007-180) Review activities: Army - AR, AV, MI Navy - EC, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 3