PCM1753 PCM1754 PCM1755 Burr-Brown Audio SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 24-BIT, 192 kHz SAMPLING ENHANCED MULTI-LEVEL, DELTA-SIGMA, AUDIO DIGITAL-TO-ANALOG CONVERTER FEATURES D 24-Bit Resolution D Analog Performance (VCC = 5 V): - - - - Dynamic Range: 106 dB SNR: 106 dB, Typical THD+N: 0.002%, Typical Full-Scale Output: 4 VPP, Typical D 4x/8x Oversampling Digital Filter: - Stop-Band Attenuation: -50 dB - Pass-Band Ripple: 0.04 dB D Sampling Frequency: 5 kHz to 200 kHz D System Clock: 128 fS, 192 fS, 256 fS, 384 fS, 512 fS, 768 fS, 1152 fS with Auto Detect D Software Control (PCM1753, PCM1755): - Accepts 16-, 18-, 20-, and 24-Bit Audio Formats: Standard, I2S, and Left-Justified - Digital Attenuation: 0 dB to -63 dB, 0.5 dB/Step - Digital De-Emphasis - Digital Filter Rolloff: Sharp or Slow - Soft Mute - Zero Flags for Each Output - Open-Drain Output Zero Flag (PCM1755) D Hardware Control (PCM1754): - - - - I2S and 16-Bit Word, Right-Justified 44.1 kHz Digital De-Emphasis Soft Mute Zero Flag for L-, R-Channel Common Output D Power Supply: 5-V Single Supply D Small 16-Lead SSOP Package, Lead-Free APPLICATIONS D A/V Receivers D DVD Movie Players D DVD Add-On Cards for High-End PCs D DVD Audio Players D HDTV Receivers D Car Audio Systems D Other Applications Requiring 24-Bit Audio DESCRIPTION The PCM1753/54/55 is a CMOS, monolithic, integrated circuit, which includes stereo digital-to-analog converters and support circuitry in a small 16-lead SSOP package. The data converters use TI's enhanced multilevel delta-sigma architecture, which employs 4th-order noise shaping and 8-level amplitude quantization to achieve excellent dynamic performance and improved tolerance to clock jitter. The PCM1753/54/55 accepts industrystandard audio data formats with 16- to 24-bit data, providing easy interfacing to audio DSP and decoder chips. Sampling rates up to 200 kHz are supported. A full set of user-programmable functions is accessible through a three-wire serial control port, which supports register write functions. The PCM1753/55 is pin-compatible with the PCM1748, PCM1742, and PCM1741, except for pin 5. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Audio Precision and System Two are trademarks of Audio Precision, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2009, Texas Instruments Incorporated PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 PACKAGE/ORDERING INFORMATION(1) PRODUCT PACKAGE PACKAGE CODE OPERATION TEMPERATURE RANGE PACKAGE MARKING PCM1753DBQ 16 pin SSOP 16-pin 16DBQ -25C 25C to 85C PCM1753 PCM1754DBQ 16 pin SSOP 16-pin 16DBQ -40C 40C to 85C PCM1754 PCM1755DBQ 16 pin SSOP 16-pin 16DBQ -25C 25C to 85C PCM1755 (1) ORDERING NUMBER TRANSPORT MEDIA PCM1753DBQ Tube PCM1753DBQR Tape and reel PCM1754DBQ Tube PCM1754DBQR Tape and reel PCM1755DBQ Tube PCM1755DBQR Tape and reel For the most current package and ordering information, see the Package Option Addendum at the end of this ducoument, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS(1) over operating free-air temperature range unless otherwise noted. UNIT Supply voltage: VCC -0.3 V to 6.5 V Ground voltage differences: AGND, DGND 0.1 V Input voltage -0.3 V to 6.5 V Input current (any pins except supplies) 10 mA Ambient temperature under bias -40C to 125C Storage temperature -55C to 150C Junction temperature 150C Lead temperature (soldering) 260C, 5 s Package temperature (IR reflow, peak) (1) 260C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS All specifications at TA = 25C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS and 24-bit data, unless otherwise noted. PARAMETER TEST CONDITIONS PCM1753DBQ, PCM1754DBQ, PCM1755DBQ MIN Resolution TYP UNIT MAX 24 Bits DATA FORMAT Audio-data Audio data interface format Audio-data Audio data bit length PCM1753 PCM1755 Standard, I2S, left-justified PCM1754 I2S, standard PCM1753 PCM1755 16-, 18-, 20-, 24-bit, selectable PCM1754 16-24-bit (I2S), 16-bit (standard) Audio data format fS 2 MSB first, 2s complement Sampling frequency 5 System clock frequency 128 fS, 192 fS, 256 fS, 384 fS, 512 fS, 768 fS, 1152 fS 200 kHz PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ELECTRICAL CHARACTERISTICS (CONTINUED) All specifications at TA = 25C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS and 24-bit data, unless otherwise noted. PARAMETER TEST CONDITIONS PCM1753DBQ, PCM1754DBQ, PCM1755DBQ MIN TYP UNIT MAX DIGITAL INPUT/OUTPUT Logic family VIH VIL Input logic level IIH(1) IIL(1) IIH(2) IIL(2) VOH(3) VOL(4) TTL compatible 2 0.8 VIN = VCC Input logic current 10 VIN = 0 V -10 VIN = VCC 65 VIN = 0 V Output logic level IOH = -1 mA VDC 100 A -10 2.4 IOL = 1 mA 0.4 VDC DYNAMIC PERFORMANCE (5) (6) THD+N at VOUT = 0 dB THD+N at VOUT = -60 60 dB fS = 44.1 kHz 0.002% fS = 96 kHz 0.003% fS = 192 kHz 0.004% fS = 44.1 kHz 0.65% fS = 96 kHz 0.8% fS = 192 kHz 0.95% EIAJ, A-weighted, fS = 44.1 kHz Dynamic range 104 A-weighted, fS = 192 kHz 102 Level linearity error 100 A-weighted, fS = 96 kHz 104 102 97 dB 106 A-weighted, fS = 192 kHz fS = 44.1 kHz Channel separation 106 A-weighted, fS = 96 kHz EIAJ, A-weighted, fS = 44.1 kHz Signal-to-noise Signal to noise ratio 100 0.006% dB 103 fS = 96 kHz 101 fS = 192 kHz 100 VOUT = -90 dB 0.5 dB dB DC ACCURACY Gain error 1 Gain mismatch, channel-to-channel Bipolar zero error 6 % of FSR 1 3 % of FSR VOUT = 0.5 VCC at BPZ 30 60 mV Full scale (0 dB) 80% of VCC VPP 50% of VCC VDC ANALOG OUTPUT Output voltage Center voltage Load impedance AC-coupled load 5 k DIGITAL FILTER PERFORMANCE FILTER CHARACTERISTICS (SHARP ROLLOFF) Pass band 0.454 fS 0.04 dB Stop band 0.546 fs Pass-band ripple Stop-band attenuation 0.04 Stop band = 0.546 fS -50 dB dB 3 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ELECTRICAL CHARACTERISTICS (CONTINUED) All specifications at TA = 25C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS and 24-bit data, unless otherwise noted. PARAMETER TEST CONDITIONS PCM1753DBQ, PCM1754DBQ, PCM1755DBQ MIN TYP UNIT MAX FILTER CHARACTERISTICS (SLOW ROLLOFF, PCM1753/PCM1755) Pass band 0.5 dB Stop band 0.198 fs 0.884 fs Pass-band ripple 0.5 Stop-band attenuation Stop band = 0.884 fS -35 Delay time dB dB 18/fs De-emphasis error s 0.1 dB ANALOG FILTER PERFORMANCE Frequency response At 20 kHz -0.03 dB At 44 kHz -0.20 dB POWER SUPPLY REQUIREMENTS (6) V CC Voltage range ICC Supply current 4.5 Power dissipation 5 5.5 fS = 44.1 kHz 16 21 fS = 96 kHz 25 fS = 192 kHz 30 fS = 44.1 kHz 80 fS = 96 kHz 125 fS = 192 kHz 150 VDC mA 105 mW TEMPERATURE RANGE Operation temperature PCM1753 PCM1755 -25 PCM1754 JA (1) (2) (3) (4) (5) (6) 4 Thermal resistance 85 -40 16-pin SSOP 85 115 C C C/W Pins 16, 1, 2, 3: SCK, BCK, DATA, LRCK. Pins 13-15: MD, MC, ML (PCM1753/PCM1755). Pins 12-15: TEST, DEMP, MUTE, FMT (PCM1754). Pins 11, 12: ZEROR, ZEROL (PCM1753). Pin 11: ZEROA (PCM1754). Pins 11, 12: ZEROR, ZEROL (PCM1753/PCM1755). Pin 11: ZEROA (PCM1754). Analog performance specifications are measured using the System Twot Cascade audio measurement system by Audio Precisiont in the averaging mode. Conditions in 192-kHz operation are system clock = 128 fS and oversampling rate = 64 fS of register 18. PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 PIN ASSIGNMENTS PCM1753/PCM1755 (TOP VIEW) PCM1754 (TOP VIEW) BCK 1 16 SCK BCK 1 16 SCK DATA 2 15 ML DATA 2 15 FMT LRCK 3 DGND 4 14 MC LRCK 3 14 MUTE 13 MD DGND 4 13 DEMP NC 5 12 ZEROL/NA VCC 6 11 ZEROR/ZEROA NC 5 12 TEST VCC 6 11 ZEROA VOUTL 7 10 VCOM VOUTL 7 10 VCOM VOUTR 8 9 AGND VOUTR 8 9 AGND FUNCTIONAL BLOCK DIAGRAM BCK 4y/8y Oversampling Digital Filter and Function Control (FMT) ML Serial Control Port Enhanced Multilevel Delta-Sigma Modulator (TEST) Output Amp and Low-Pass Filter VOUTR System Clock Zero Detect (1) Open-Drain Output for the PCM1755 ZEROR/ZEROA(1) (ZEROA) System Clock Manager ZEROL/NA(1) SCK VCOM DAC (DEMP) MD VOUTL Power Supply AGND (MUTE) MC Output Amp and Low-Pass Filter DAC VCC DATA Audio Serial Port DGND LRCK NOTE: Pin names in (parentheses) are valid for the PCM1754 only. 5 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION PCM1753/PCM1755 AGND 9 - Analog ground BCK 1 I Audio data bit clock input DATA 2 I Audio data digital input DGND 4 - Digital ground LRCK 3 I L-channel and R-channel audio data latch enable input MC 14 I Mode control clock input(1) MD 13 I Mode control data input (1) ML 15 I Mode control latch input (1) NC 5 - SCK 16 I System clock input VCC 6 - Analog power supply, 5 V VCOM 10 - Common voltage decoupling VOUTL 7 O Analog output for L-channel VOUTR 8 O Analog output for R-channel ZEROR/ZEROA 11 O Zero flag output for R-channel/Zero flag output for L-/R-channels (2) ZEROL/NA 12 O Zero flag output for L-channel/Not assigned (2) AGND 9 - Analog ground BCK 1 I Audio-data bit-clock input DATA 2 I Audio-data digital input DEMP 13 I De-emphasis control (1) DGND 4 - Digital ground FMT 15 I Data format select (1) LRCK 3 I L-channel and R-channel audio data latch enable input MUTE 14 I Analog mixing control (1) NC 5 - SCK 16 I System clock input TEST 12 I Test pin. Ground or open (1) VCC 6 - Analog power supply, 5 V VCOM 10 - Common voltage decoupling VOUTL 7 O Analog output for L-channel VOUTR 8 O Analog output for R-channel ZEROA 11 O Zero flag output for L/R channels PCM1754 (1) Schmitt-trigger input with internal pulldown. (2) Open-drain output (PCM1755). 6 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 TYPICAL PERFORMANCE CURVES DIGITAL FILTER (DE-EMPHASIS OFF) AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 0.05 0.04 -20 0.03 0.02 Amplitude - dB Amplitude - dB -40 -60 -80 0.01 0.00 -0.01 -0.02 -100 -0.03 -120 -140 -0.04 0 1 2 3 -0.05 0.0 4 0.1 0.2 0.3 0.4 0.5 Frequency [x fS] Frequency [x fS] Figure 1. Frequency Response, Sharp Rolloff Figure 2. Pass-Band Ripple, Sharp Rolloff AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 5 4 -20 3 2 Amplitude - dB Amplitude - dB -40 -60 -80 1 0 -1 -2 -100 -3 -120 -140 -4 0 1 2 3 4 -5 0.0 0.1 0.2 0.3 0.4 Frequency [x fS] Frequency [x fS] Figure 3. Frequency Response, Slow Rolloff Figure 4. Transition Characteristics, Slow Rolloff 0.5 All specifications at TA = 25_C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, unless otherwise noted 7 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 DE-EMPHASIS CURVES DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 0 0.5 fS = 32 kHz -1 0.3 De-emphasis Error - dB De-emphasis Level - dB -2 -3 -4 -5 -6 -7 0.1 0.0 -0.1 -0.2 -0.3 -9 -0.4 0 2 4 6 8 10 12 -0.5 14 2 4 6 8 Figure 5 Figure 6 DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 12 14 0.5 fS = 44.1 kHz fS = 44.1 kHz 0.4 0.3 De-emphasis Error - dB -2 -3 -4 -5 -6 -7 0.2 0.1 0.0 -0.1 -0.2 -8 -0.3 -9 -0.4 0 2 4 6 8 10 12 14 16 18 20 -0.5 0 2 4 6 8 10 12 14 f - Frequency - kHz f - Frequency - kHz Figure 7 Figure 8 All specifications at TA = 25_C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, unless otherwise noted 8 10 f - Frequency - kHz -1 -10 0 f - Frequency - kHz 0 De-emphasis Level - dB 0.2 -8 -10 fS = 32 kHz 0.4 16 18 20 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 DE-EMPHASIS CURVES (CONTINUED) DE-EMPHASIS LEVEL vs FREQUENCY DE-EMPHASIS ERROR vs FREQUENCY 0 0.5 fS = 48 kHz -1 0.3 De-emphasis Error - dB De-emphasis Level - dB -2 -3 -4 -5 -6 -7 0.2 0.1 0.0 -0.1 -0.2 -8 -0.3 -9 -0.4 -10 fS = 48 kHz 0.4 0 2 4 6 8 10 12 14 16 18 20 22 -0.5 0 2 4 6 8 10 12 14 f - Frequency - kHz f - Frequency - kHz Figure 9 Figure 10 16 18 20 22 All specifications at TA = 25_C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, unless otherwise noted 9 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ANALOG DYNAMIC PERFORMANCE (SUPPLY VOLTAGE CHARACTERISTICS) TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE DYNAMIC RANGE vs SUPPLY VOLTAGE 110 192 kHz, 128 fS 96 kHz, 384 fS 1 108 -60 dB 44.1 kHz, 384 fS Dynamic Range - dB THD+N - Total Harmonic Distortion + Noise - % 10 44.1 kHz, 384 fS 0.1 96 kHz, 384 fS 192 kHz, 128 fS 0.01 0 dB 0.001 0.0001 4.0 44.1 kHz, 384 fS 4.5 5.0 5.5 96 kHz, 384 fS 104 192 kHz, 128 fS 102 100 98 96 4.0 6.0 4.5 5.0 VCC - Supply Voltage - V Figure 11 Figure 12 SIGNAL-to-NOISE RATIO vs SUPPLY VOLTAGE CHANNEL SEPARATION vs SUPPLY VOLTAGE 6.0 110 108 108 44.1 kHz, 384 fS Channel Separation - dB 106 96 kHz, 384 fS 104 192 kHz, 128 fS 102 100 98 96 4.0 106 104 44.1 kHz, 384 fS 102 96 kHz, 384 fS 100 192 kHz, 128 fS 98 4.5 5.0 5.5 6.0 96 4.0 4.5 5.0 5.5 VCC - Supply Voltage - V VCC - Supply Voltage - V Figure 13 Figure 14 All specifications at TA = 25_C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, unless otherwise noted 10 5.5 VCC - Supply Voltage - V 110 SNR - Signal-to-Noise Ratio - dB 106 6.0 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ANALOG DYNAMIC PERFORMANCE (TEMPERATURE CHARACTERISTICS) TOTAL HARMONIC DISTORTION + NOISE vs FREE-AIR TEMPERATURE DYNAMIC RANGE vs FREE-AIR TEMPERATURE 110 192 kHz, 128 fS 96 kHz, 384 fS 44.1 kHz, 384 fS 44.1 kHz, 384 fS 0.1 192 kHz, 128 fS 96 kHz, 384 fS 0.01 0.001 0.0001 -50 108 -60 dB 1 Dynamic Range - dB THD+N - Total Harmonic Distortion + Noise - % 10 0 dB 44.1 kHz, 384 fS -25 0 25 96 kHz, 384 fS 104 102 192 kHz, 128 fS 100 98 50 75 96 -50 100 -25 0 25 50 TA - Free-Air Temperature - C TA - Free-Air Temperature - C Figure 15 Figure 16 SIGNAL-to-NOISE RATIO vs FREE-AIR TEMPERATURE CHANNEL SEPARATION vs FREE-AIR TEMPERATURE 110 75 100 110 108 108 44.1 kHz, 384 fS 106 Channel Separation - dB SNR - Signal-to-Noise Ratio - dB 106 96 kHz, 384 fS 104 102 192 kHz, 128 fS 100 98 96 -50 106 104 44.1 kHz, 384 fS 96 kHz, 384 fS 102 192 kHz, 128 fS 100 98 -25 0 25 50 75 100 96 -50 -25 0 25 50 TA - Free-Air Temperature - C TA - Free-Air Temperature - C Figure 17 Figure 18 75 100 All specifications at TA = 25_C, VCC = 5 V, fS = 44.1 kHz, system clock = 384 fS, and 24-bit data, unless otherwise noted -25C to 85C for the PCM1753/55, -40C to 85C for the PCM1754 . 11 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 SYSTEM CLOCK AND RESET FUNCTIONS System Clock Input The PCM1753/54/55 requires a system clock for operating the digital interpolation filters and multilevel delta-sigma modulators. The system clock is applied at the SCK input (pin 16). Table 1 shows examples of system clock frequencies for common audio sampling rates. Figure 19 shows the timing requirements for the system clock input. For optimal performance, it is important to use a clock source with low phase-jitter and noise. TI's PLL170x family of multiclock generators is an excellent choice for providing the PCM1753/54/55 system clock. Table 1. System Clock Rates for Common Audio Sampling Frequencies SYSTEM CLOCK FREQUENCY (fSCLK) (MHz) (1) SAMPLING FREQUENCY 128 fS 192 fS 256 fS 384 fS 512 fS 768 fS 1152 fS 8 kHz 1.0240 1.5360 2.0480 3.0720 4.0960 6.1440 9.2160 16 kHz 2.0480 3.0720 4.0960 6.1440 8.1920 12.2880 18.4320 32 kHz 4.0960 6.1440 8.1920 12.2880 16.3840 24.5760 36.8640 44.1 kHz 5.6448 8.4672 11.2896 16.9344 22.5792 33.8688 (1) 48 kHz 6.1440 9.2160 12.2880 18.4320 24.5760 36.8640 (1) 88.2 kHz 11.2896 16.9344 22.5792 33.8688 45.1584 (1) (1) 96 kHz 12.2880 18.4320 24.5760 36.8640 49.1520 (1) (1) 192 kHz 24.5760 36.8640 (1) (1) (1) (1) (1) This system clock rate is not supported for the given sampling frequency. t(SCKH) H 2.0 V System Clock (SCK) 0.8 V L t(SCKL) PARAMETERS t(SCY) SYMBOL MIN System clock pulse duration, high t(SCKH) 7 System clock pulse duration, low t(SCKL) 7 System clock pulse cycle time (1) t(SCY) 1/128 fS, 1/256 fS, 1/384 fS, 1/512 fS, 1/768 fS, or 1/1152 fS Figure 19. System Clock Input Timing 12 TYP MAX UNITS ns ns (1) ns PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Power-On Reset Functions The PCM1753/54/55 includes a power-on reset function. Figure 20 shows the operation of this function. With the system clock active and VCC > 3 V (typical, 2.2 V to 3.7 V), the power-on reset function is enabled. The initialization sequence requires 1024 system clocks from the time VCC > 3 V (typical, 2.2 V to 3.7 V). After the initialization period, the PCM1753/55 is set to its reset default state, as described in the Mode Control Registers section of this data sheet. During the reset period (1024 system clocks), the analog output is forced to the bipolar zero level, or VCC/2. After the reset period, an internal register is initialized in the next 1/fS period and if SCK, BCK, and LRCK are provided continuously, the PCM1753/54/55 provides proper analog output with unit group delay against the input data. VCC 3.7 V (Max) 3.0 V (Typ) 2.2 V (Min) Reset Reset Removal Internal Reset Don't Care 1024 System Clocks System Clock Figure 20. Power-On Reset Timing 13 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 AUDIO SERIAL INTERFACE The audio serial interface for the PCM1753/54/55 consists of a 3-wire synchronous serial port. It includes LRCK (pin 3), BCK (pin 1), and DATA (pin 2). BCK is the serial audio bit clock, and it is used to clock the serial data present on DATA into the serial shift register of the audio interface. Serial data is clocked into the PCM1753/54/55 on the rising edge of BCK. LRCK is the serial audio left/right word clock. It is used to latch serial data into the internal registers of the serial audio interface. Both LRCK and BCK should be synchronous to the system clock. Ideally, it is recommended that LRCK and BCK be derived from the system clock input, SCK. LRCK is operated at the sampling frequency, fS. BCK can be operated at 32, 48, or 64 times the sampling frequency for standard (right-justified) format, and 32 times the sampling frequency of BCK is limited to 16-bit right-justified format only. BCK can be operated at 48 or 64 times the sampling frequency for the I2S and left-justified formats. 48 times the sampling frequency of BCK is limited to 192/384/768 fS SCKI. Internal operation of the PCM1753/54/55 is synchronized with LRCK. Accordingly, internal operation is held when the sampling rate clock of LRCK is changed or when SCK and/or BCK is interrupted for a 3-bit clock cycle or longer. If SCK, BCK, and LRCK are provided continuously after this held condition, the internal operation is re-synchronized automatically in a period of less than 3/fS. External resetting is not required. Audio Data Formats and Timing The PCM1753/55 supports industry-standard audio data formats, including right-justified, I2S, and left-justified. The PCM1754 supports I2S and 16-bit-word right-justified. The data formats are shown in Figure 22. Data formats are selected using the format bits, FMT[2:0], located in control register 20 of the PCM1753/55, and are selected using the FMT pin on the PCM1754. The default data format is 24-bit left-justified. All formats require binary 2s-complement, MSB-first audio data. Figure 21 shows a detailed timing diagram for the serial audio interface. 1.4 V LRCK t(BCH) t(BCL) t(LB) 1.4 V BCK t(BCY) t(BL) 1.4 V DATA t(DS) t(DH) PARAMETERS SYMBOL MIN BCK pulse cycle time t(BCY) 1/(32 fS), 1/(48 fS), 1/(64 fS) (1) BCK high-level time t(BCH) 35 ns BCK low-level time t(BCL) 35 ns BCK rising edge to LRCK edge t(BL) 10 ns LRCK falling edge to BCK rising edge t(LB) 10 ns DATA setup time t(DS) 10 ns DATA hold time t(DH) 10 ns (1) fS is the sampling frequency (e.g., 44.1 kHZ, 48 kHz, 96 kHz, etc.). Figure 21. Audio Interface Timing 14 MAX UNITS PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 (1) Standard Data Format; L-Channel = HIGH, R-Channel = LOW 1/fS LRCK L-Channel R-Channel BCK (= 32 fS, 48 fS, or 64 fS) 16-Bit Right-Justified, BCK = 48 fS or 64 fS DATA 14 15 16 1 2 3 14 15 16 MSB 1 LSB 2 3 14 15 16 MSB LSB 16-Bit Right-Justified, BCK = 32 fS DATA 14 15 16 1 2 3 14 15 16 MSB 1 LSB 2 3 14 15 16 MSB LSB 18-Bit Right-Justified, BCK = 48 fS or 64 fS DATA 16 17 18 1 2 3 16 17 18 MSB 1 LSB 2 3 16 17 18 MSB LSB 20-Bit Right-Justified, BCK = 48 fS or 64 fS DATA 18 19 20 1 2 3 18 19 20 MSB 1 LSB 2 3 18 19 20 MSB LSB 24-Bit Right-Justified, BCK = 48 fS or 64 fS DATA 22 23 24 1 2 3 22 23 24 MSB 1 2 LSB 3 22 23 24 MSB LSB (2) I2S Data Format; L-Channel = LOW, R-Channel = HIGH 1/fS LRCK L-Channel R-Channel BCK (= 48 fS or 64 fS) DATA 1 2 3 N-2 N-1 MSB N 1 LSB 2 3 N-2 N-1 MSB LSB N 1 2 (3) Left-Justified Data Format; L-Channel = HIGH, R-Channel = LOW 1/fS LRCK L-Channel R-Channel BCK (= 48 fS, or 64 fS) DATA 1 2 3 MSB N-2 N-1 LSB N 1 2 3 MSB N-2 N-1 N 1 2 LSB Figure 22. Audio Data Input Formats 15 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ZERO FLAGS (PCM1753/55) Zero-Detect Condition Zero detection for either output channel is independent from the other channel. If the data for a given channel remains at a 0 level for 1024 sample periods (or LRCK clock periods), a zero-detect condition exists for that channel. Zero Flag Outputs If a zero-detect condition exists for one or more channels, the zero flag pins for those channels are set to a logic 1 state. There are zero flag pins for each channel, ZEROL (pin 12) and ZEROR (pin 11). These pins can be used to operate external mute circuits, or used as status indicators for a microcontroller, audio signal processor, or other digitally controlled function. The active polarity of zero flag outputs can be inverted by setting the ZREV bit of control register 22 to 1. The reset default is active-high output, or ZREV = 0. The L-channel and R-channel common zero flag can be selected by setting the AZRO bit of control register 22 to 1. The reset default is independent zero flags for L-channel and R-channel, or AZRO = 0. In the case of the PCM1755, ZEROL and ZEROR are open-drain outputs. ZERO FLAG (PCM1754) The PCM1754 has a ZERO flag pin, ZEROA (pin 11). ZEROA is the L-channel and R-channel common zero flag pin. If the data for L-channel and R-channel remains at a 0 level for 1024 sampling periods (or LRCK clock periods), ZEROA is set to a logic 1 state. HARDWARE CONTROL (PCM1754) The digital functions of the PCM1754 are capable of hardware control. Table 2 shows selectable formats, Table 3 shows de-emphasis control, and Table 4 shows mute control. Table 2. Data Format Select FMT (PIN 15) DATA FORMAT LOW 16- to 24-bit, I2S format HIGH 16-bit right-justified Table 3. De-Emphasis Control DEMP (PIN 13) DE-EMPHASIS FUNCTION LOW 44.1 kHz de-emphasis OFF HIGH 44.1 kHz de-emphasis ON Table 4. Mute Control MUTE (PIN 14) MUTE LOW Mute OFF HIGH Mute ON OVERSAMPLING RATE CONTROL (PCM1754) The PCM1754 automatically controls the oversampling rate of the delta-sigma D/A converters with the system clock rate. The oversampling rate is set to 64x oversampling with every system clock and sampling frequency. 16 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 SOFTWARE CONTROL (PCM1753/55) The PCM1753/55 has many programmable functions which can be controlled in the software control mode. The functions are controlled by programming the internal registers using ML, MC, and MD. The serial control interface is a 3-wire serial port, which operates asynchronously to the audio serial interface. The serial control interface is used to program the on-chip mode registers. The control interface includes MD (pin 13), MC (pin 14), and ML (pin 15). MD is the serial data input, used to program the mode registers. MC is the serial bit clock, used to shift data into the control port. ML is the control port latch clock. Register Write Operation All write operations for the serial control port use 16-bit data words. Figure 23 shows the control data word format. The most significant bit must be a 0. There are seven bits, labeled IDX[6:0], that set the register index (or address) for the write operation. The least significant eight bits, D[7:0], contain the data to be written to the register specified by IDX[6:0]. Figure 24 shows the functional timing diagram for writing to the serial control port. ML is held at a logic 1 state until a register needs to be written. To start the register write cycle, ML is set to logic 0. Sixteen clocks are then provided on MC, corresponding to the 16 bits of the control data word on MD. After the sixteenth clock cycle has completed, ML is set to logic 1 to latch the data into the indexed mode control register. LSB MSB 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 Register Index (or Address) D4 D3 D2 D1 D0 Register Data Figure 23. Control Data Word Format for MD ML MC MD X 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5 D4 D3 D2 D1 D0 X X 0 IDX6 Figure 24. Register Write Operation 17 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Control Interface Timing Requirements Figure 25 shows a detailed timing diagram for the serial control interface. These timing parameters are critical for proper control port operation. t(MHH) ML t(MLS) t(MCL) t(MCH) t(MLH) MC t(MCY) LSB MD t(MDS) t(MDH) PARAMETERS SYMBOL MIN t(MCY) 100 ns MC low-level time t(MCL) 50 ns MC high-level time t(MCH) 50 ns ML high-level time t(MHH) (2) ns ML falling edge to MC rising edge t(MLS) 20 ns ML hold time (1) t(MLH) 20 ns MD hold time t(MDH) 15 ns MD setup time t(MDS) 20 ns MC pulse cycle time (1) MC rising edge for LSB to ML rising edge. 3 (2) sec (min); fS: sampling rate fS 256 Figure 25. Control Interface Timing 18 TYP MAX UNITS PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 MODE CONTROL REGISTERS (PCM1753/55) User-Programmable Mode Controls The PCM1753/55 includes a number of user programmable functions, which are accessed via control registers. The registers are programmed using the serial control interface, which was previously discussed in this data sheet. Table 5 lists the available mode control functions, along with their reset default conditions and associated register index. Register Map The mode control register map is shown in Table 6. Each register includes an index (or address) indicated by the IDX[6:0] bits. Table 5. User-Programmable Mode Controls FUNCTION Digital attenuation control, 0 dB to -63 dB in 0.5-dB steps RESET DEFAULT REGISTER BIT(s) 0 dB, no attenuation 16 and 17 AT1[7:0], AT2[7:0] Soft mute control Oversampling rate control (64 fS or 128 fS) Mute disabled 18 MUT[2:0] 64 fS oversampling 18 OVER Soft reset control DAC operation control De-emphasis function control Reset disabled 18 SRST DAC1 and DAC2 enabled 19 DAC[2:1] De-emphasis disabled 19 DM12 De-emphasis sample rate selection 44.1 kHz 19 DMF[1:0] 24-bit left-justified 20 FMT[2:0] Digital filter rolloff control Sharp rolloff 20 FLT Zero flag function select L-, R-channel independent 22 AZRO Normal phase 22 DREV High 22 ZREV Audio data format control Output phase select Zero flag polarity select Table 6. Mode Control Register Map IDX (B8-B14) REGISTER B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 10h Register 16 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT17 AT16 AT15 AT14 AT13 11h Register 17 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT27 AT26 AT25 AT24 AT23 12h Register 18 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 SRST OVER RSV RSV RSV 13h Register 19 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV DMF1 DMF0 DM12 14h Register 20 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV FLT RSV 16h Register 22 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV RSV RSV B1 B0 AT12 AT11 AT10 AT22 AT21 AT20 RSV MUT2 MUT1 RSV RSV DAC2 DAC1 RSV FMT2 FMT1 FMT0 RSV AZRO ZREV DREV NOTE: RSV: Reserved for test operation. It should be set to 0 for regular operation. 19 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Register Definitions Register 16 Register 17 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT17 AT16 AT15 AT14 AT13 AT12 AT11 AT10 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 AT27 AT26 AT25 AT24 AT23 AT22 AT21 AT20 ATx[7:0]: Digital Attenuation Level Setting Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2). Default value: 1111 1111b Each DAC channel (VOUTL and VOUTR) includes a digital attenuation function. The attenuation level can be set from 0 dB to -63 dB in 0.5-dB steps. Changes in attenuator levels are made by incrementing or decrementing one step (0.5 dB) for every 8/fS time internal until the programmed attenuator setting is reached. Alternatively, the attenuation level can be set to infinite attenuation (or mute). The attenuation data for each channel can be set individually. The attenuation level is set using the following formula: Attenuation level (dB) = 0.5 x (ATx[7:0] DEC - 255) where ATx[7:0] DEC = 0 through 255. For ATx[7:0] DEC = 0 through 128, attenuation is set to infinite attenuation. The following table shows the attenuation levels for various settings: Register 18 ATx[7:0] DECIMAL VALUE ATTENUATION LEVEL SETTING 1111 1111b 255 0 dB, No Attenuation. (default) 1111 1110b 254 -0.5 dB 1111 1101b 253 -1.0 dB L L L 1000 0011b 131 -62.0 dB 1000 0010b 130 -62.5 dB 1000 0001b 129 -63.0 dB 1000 0000b 128 Mute L L L 0000 0000B 0 Mute B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 SRST OVER RSV RSV RSV RSV MUT2 MUT1 MUTx: Soft Mute Control where x = 1 or 2, corresponding to the DAC outputs VOUT L (x = 1) and VOUTR (x = 2). Default value: 0 MUTx = 0 Mute disabled (default) MUTx = 1 Mute enabled The mute bits, MUT1 and MUT2, are used to enable or disable the soft mute function for the corresponding DAC outputs, VOUTL and VOUTR. The soft mute function is incorporated into the digital attenuators. When mute is disabled (MUTx = 0), the attenuator and DAC operate normally. When mute is enabled by setting MUTx = 1, the digital attenuator for the corresponding output is decreased from the current setting to infinite attenuation, one attenuator step (0.5 dB) for every 8/fS seconds. This provides pop-free muting of the DAC output. 20 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 By setting MUTx = 0, the attenuator is increased one step for every 8/fS seconds to the previously programmed attenuation level. OVER: Oversampling Rate Control Default value: 0 System clock rate = 256 fS, 384 fS, 512 fS, 768 fS, or 1152 fS: OVER = 0 64x oversampling (default) OVER = 1 128x oversampling System clock rate = 128 fS or 192 fS: OVER = 0 32x oversampling (default) OVER = 1 64x oversampling The OVER bit is used to control the oversampling rate of the delta-sigma D/A converters. The OVER = 1 setting is recommended when the sampling rate is 192 kHz (system clock rate is 128 fS or 192 fS). SRST: Reset Default value: 0 SRST = 0 Reset disabled (default) SRST = 1 Reset enabled The SRST bit is used to enable or disable the soft reset function. The operation is the same as power-on reset. All registers are initialized. Register 19 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV DMF1 DMF0 DM12 RSV RSV DAC2 DAC1 DACx: DAC Operation Control Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) or VOUTR (x = 2). Default value: 0 DACx = 0 DAC operation enabled (default) DACx = 1 DAC operation disabled The DAC operation controls are used to enable and disable the DAC outputs, VOUTL and VOUTR. When DACx = 0, the corresponding output generates the audio waveform dictated by the data present on the DATA pin. When DACx = 1, the corresponding output is set to the bipolar zero level, or 0.5 VCC. DM12: Digital De-Emphasis Function Control Default value: 0 DM12 = 0 De-emphasis disabled (default) DM12 = 1 De-emphasis enabled The DM12 bit is used to enable or disable the digital de-emphasis function. See the plots shown in the Typical Performance Curves section of this data sheet. 21 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 DMF[1:0]: Sampling Frequency Selection for the De-Emphasis Function Default value: 00 The DMF[1:0] bits are used to select the sampling frequency used for the digital de-emphasis function when it is enabled. DMF[1:0] Register 20 De-Emphasis Sample Rate Selection 00 44.1 kHz (default) 01 48 kHz 10 32 kHz 11 Reserved B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV FLT RSV RSV FMT2 FMT1 FMT0 FMT[2:0]: Audio Interface Data Format Default value: 101 The FMT[2:0] bits are used to select the data format for the serial audio interface. The following table shows the available format options. FMT[2:0] Audio Data Format Selection 000 24-bit standard format, right-justified data 001 20-bit standard format, right-justified data 010 18-bit standard format, right-justified data 011 16-bit standard format, right-justified data 100 16- to 24-bit I2S format 101 16- to 24-bit left-justified format (default) 110 Reserved 111 Reserved FLT: Digital Filter Rolloff Control Default value: 0 FLT = 0 Sharp rolloff (default) FLT = 1 Slow rolloff The FLT bit allows the user to select the digital filter rolloff that is best suited to the application. Two filter rolloff selections are available, sharp and slow. The filter responses for these selections are shown in the Typical Performance Curves section of this data sheet. Register 22 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 RSV RSV RSV RSV RSV AZRO ZREV DREV DREV: Output Phase Select Default value: 0 DREV = 0 Normal output (default) DREV = 1 Inverted output The DREV bit is the output analog signal phase control. 22 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 ZREV: Zero Flag Polarity Select Default value: 01h ZREV = 0 High on zero flag pins indicates a zero detect (default) ZREV = 1 Low on zero flag pins indicates a zero detect The ZREV bit allows the user to select the polarity of zero flag pins. AZRO: Zero Flag Function Select Default value: 0 AZRO = 0 L-/R-channel independent zero flags (default) AZRO = 1 L-/R-channel common zero flag The AZRO bit allows the user to select the function of zero flag pins. AZRO = 0: Pin 11: ZEROR, zero flag output for R-channel Pin 12: ZEROL, zero flag output for L-channel AZRO = 1: Pin 11: ZEROA, zero flag output for L-/R-channels Pin 12: NA, not assigned ANALOG OUTPUTS The PCM1753/54/55 includes two independent output channels, VOUTL and VOUTR. These are unbalanced outputs, each capable of driving 4 VPP typical into a 5-k ac-coupled load. The internal output amplifiers for VOUTL and VOUTR are biased to the dc common-mode (or bipolar zero) voltage, equal to 0.5 VCC. The output amplifiers include an RC continuous-time filter, which helps to reduce the out-of-band noise energy present at the DAC outputs due to the noise shaping characteristics of the PCM1753/54/55 delta-sigma D/A converters. The frequency response of this filter is shown in Figure 26. By itself, this filter is not enough to attenuate the out-of-band noise to an acceptable level for many applications. An external low-pass filter is required to provide sufficient out-of-band noise rejection. Further discussion of DAC post-filter circuits is provided in the Applications Information section of this data sheet. LEVEL vs FREQUENCY 10 0 Level - dB -10 -20 -30 -40 -50 -60 0.1 1 10 100 1k 10k f - Frequency - kHz Figure 26. Output Filter Frequency Response 23 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 VCOM Output One unbuffered common-mode voltage output pin, VCOM (pin 10) is brought out for decoupling purposes. This pin is nominally biased to a dc voltage level equal to 0.5 VCC. This pin can be used to bias external circuits. Figure 27 shows an example of using the VCOM pin for external biasing applications. AV + *1, where A V + * PCM1753/54/55 R3 2 VOUTX(1) 3 C2 10 F - 1/2 OPA2353 1 + R1 VCC C1 R2 + VCOM + (1) X 10 F = L or R (a) Using VCOM to Bias a Single-Supply Filter Stage VCC PCM1753/54/55 - OPA337 Buffered VCOM + VCOM + 10 F (b) Using a Voltage Follower to Buffer VCOM When Biasing Multiple Nodes Figure 27. Biasing External Circuits Using the VCOM Pin 24 R2 R1 Filtered Output PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 APPLICATION INFORMATION CONNECTION DIAGRAMS A basic connection diagram is shown in Figure 28, with the necessary power supply bypassing and decoupling components. TI recommends using the component values shown in Figure 28 for all designs. The use of series resistors (22 to 100 ) is recommended for the SCK, LRCK, BCK, and DATA inputs. The series resistor combines with the stray PCB and device input capacitance to form a low-pass filter, which reduces high-frequency noise emissions and helps to dampen glitches and ringing present on clock and data lines. DATA ML 15 3 LRCK MC 14 4 DGND MD 13 5 NC ZEROL/NA 12 6 VCC ZEROR/ZEROA 11 7 VOUTL VCOM 10 + + 10 mF 10 F 8 VOUTR AGND 9 10 F + 2 System Clock 16 + +5 V BCK PCM1753 PCM1755 SCK PCM Audio Data 1 Register Control Zero Mute Control 10 mF Post LPF Post LPF L-Ch Out R-Ch Out 16 System Clock DATA FMT 15 Format 3 LRCK MUTE 14 MUTE On/Off 4 DGND DEMP 13 DEMP On/Off 5 NC TEST 12 6 VCC ZEROA 11 + 7 VOUTL VCOM 10 + + 8 VOUTR AGND 9 10 F PCM Audio Data +5 V 10 mF 10 F PCM1754 SCK + 1 BCK 2 Zero Mute Control 10 mF Post LPF Post LPF L-Ch Out R-Ch Out Figure 28. Basic Connection Diagram 25 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 POWER SUPPLIES AND GROUNDING The PCM1753/54/55 requires 5 V for VCC. Proper power supply bypassing is shown in Figure 28. The 10-F capacitors should be tantalum or aluminum electrolytic. D/A OUTPUT FILTER CIRCUITS Delta-sigma D/A converters use noise-shaping techniques to improve in-band signal-to-noise ratio (SNR) performance at the expense of generating increased out-of-band noise above the Nyquist frequency, or fS/2. The out-of-band noise must be low-pass filtered in order to provide the optimal converter performance. This is accomplished by a combination of on-chip and external low-pass filtering. Figure 27(a) and Figure 29 show the recommended external low-pass active filter circuits for single- and dual-supply applications. These circuits are 2nd-order Butterworth filters using the multiple feedback (MFB) circuit arrangement, which reduces sensitivity to passive component variations over frequency and temperature. For more information regarding MFB active filter design, see Burr-Brown applications bulletin (SBAA055), available from the TI Web site at http://www.ti.com. Because the overall system performance is defined by the quality of the D/A converters and their associated analog output circuitry, high-quality audio operational amplifiers are recommended for the active filters. TI's OPA2353 and OPA2134 dual operational amplifiers are shown in Figure 27(a) and Figure 29, and are recommended for use with the PCM1753/54/55. R2 R1 VIN C2 AV [ * C1 R3 2 3 - OPA2134 1 + R4 VOUT R2 R1 Figure 29. Dual-Supply Filter Circuit PCB LAYOUT GUIDELINES A typical PCB floor plan for the PCM1753/54/55 is shown in Figure 30. A ground plane is recommended, with the analog and digital sections being isolated from one another using a split or cut in the circuit board. The PCM1753/54/55 should be oriented with the digital I/O pins facing the ground plane split/cut to allow for short, direct connections to the digital audio interface and control signals originating from the digital section of the board. 26 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Digital Power +VD Analog Power DGND AGND +5VA +VS -VS VCC Digital Logic and Audio Processor Output Circuits DGND PCM1753/54/55 Digital Ground AGND Digital Section Analog Ground Analog Section Return Path for Digital Signals Figure 30. Recommended PCB Layout Separate power supplies are recommended for the digital and analog sections of the board. This prevents the switching noise present on the digital supply from contaminating the analog power supply and degrading the dynamic performance of the PCM1753/54/55. In cases where a common 5-V supply must be used for the analog and digital sections, an inductance (RF choke, ferrite bead) should be placed between the analog and digital 5-V supply connections to avoid coupling of the digital switching noise into the analog circuitry. Figure 31 shows the recommended approach for single-supply applications. Power Supplies RF Choke or Ferrite Bead +5V VDD AGND +VS -VS VCC DGND Output Circuits PCM1753/54/55 AGND Digital Section Analog Section Common Ground Figure 31. Single-Supply PCB Layout 27 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 THEORY OF OPERATION The delta-sigma section of the PCM1753/54/55 is based on an 8-level amplitude quantizer and a 4th-order noise shaper. This section converts the oversampled input data to 8-level delta-sigma format. A block diagram of the 8-level delta-sigma modulator is shown in Figure 32. This 8-level delta-sigma modulator has the advantage of stability and clock jitter sensitivity over the typical one-bit (2-level) delta-sigma modulator. The combined oversampling rate of the delta-sigma modulator and the interpolation filter is 64 fS. The theoretical quantization noise performance of the 8-level delta-sigma modulator is shown in Figure 33 and Figure 34. The enhanced multilevel delta-sigma architecture also has advantages for input clock jitter sensitivity due to the multilevel quantizer, with the simulated jitter sensitivity shown in Figure 35. KEY PERFORMANCE PARAMETERS AND MEASUREMENT This section provides information on how to measure key dynamic performance parameters for the PCM1753/54/55. In all cases, an Audio Precision System Two Cascade audio measurement system or equivalent is used to perform the testing. Total Harmonic Distortion + Noise Total harmonic distortion + noise (THD+N) is a significant figure of merit for audio D/A converters because it takes into account both harmonic distortion and all noise sources within a specified measurement bandwidth. The average value of the distortion and noise is referred to as THD+N. For the PCM1753/54/55, THD+N is measured with a full-scale, 1-kHz digital sine wave as the test stimulus at the input of the DAC. The digital generator is set to 24-bit audio word length and a sampling frequency of 44.1 kHz or 96 kHz. The digital generator output is taken from the unbalanced S/PDIF connector of the measurement system. The S/PDIF data is transmitted via a coaxial cable to the digital audio receiver on the DEM-DAI1753 demonstration board. The receiver is then configured to output 24-bit data in either I2S or left-justified data format. The DAC audio interface format is programmed to match the receiver output format. The analog output is then taken from the DAC post filter and connected to the analog analyzer input of the measurement system. The analog input is band limited using filters resident in the analyzer. The resulting THD+N is measured by the analyzer and displayed by the measurement system. - + IN 8 fS + + - Z-1 + + Z-1 + + + Z-1 + + + 8-Level Quantizer OUT 64 fS Figure 32. Eight-Level Delta-Sigma Modulator 28 + + Z-1 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 AMPLITUDE vs FREQUENCY 0 -20 -20 -40 -40 -60 -60 Amplitude - dB 0 -80 -100 -120 -80 -100 -120 -140 -140 -160 -160 -180 0 1 2 3 4 5 6 7 -180 8 0 1 2 Frequency [ fS] 3 4 5 6 7 8 Frequency [ fS] Figure 33. Quantization Noise Spectrum ( 64 Oversampling) Figure 34. Quantization Noise Spectrum ( 128 Oversampling) DYNAMIC RANGE vs JITTER 125 120 Dynamic Range - dB Amplitude - dB AMPLITUDE vs FREQUENCY 115 110 105 100 95 90 0 100 200 300 400 500 600 Jitter - ps p-p Figure 35. Jitter Dependence ( 64 Oversampling) 29 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Dynamic Range Dynamic range is specified as A-weighted THD+N measured with a -60-dB full-scale, 1-kHz digital sine wave stimulus at the input of the D/A converter. This measurement is designed to give a good indicator of how the DAC performs given a low-level input signal. The measurement setup for the dynamic range measurement is shown in Figure 37, and is similar to the THD+N test setup discussed previously. The differences include the band limit filter selection, the additional A-weighting filter, and the -60-dB full-scale input level. Evaluation Board DEM-DAI1753 S/PDIF Receiver 2nd-Order Low-Pass Filter PCM1753/54/55 f-3 dB = 54 kHz or 108 kHz Audio Precision System Two S/PDIF Output Digital Generator 0 dB FS (100% Full-Scale), 24-Bit, 1-kHz Sine Wave Analyzer and Display Averaging Mode AES17 Filter Band Limit HPF = 400 Hz LPF = 30 kHz f-3 dB = 20.9 kHz Figure 36. Test Setup for THD+N Measurement Idle Channel Signal-to-Noise Ratio The SNR test provides a measure of the noise floor of the D/A converter. The input to the D/A is all-0s data, and the dither function of the digital generator must be disabled to ensure an all-0s data stream at the input of the D/A converter. The measurement setup for SNR is identical to that used for dynamic range, with the exception of the input signal level. (See the note provided in Figure 37). 30 PCM1753 PCM1754 PCM1755 www.ti.com SLES092C - OCTOBER 2003 - REVISED FEBRUARY 2009 Evaluation Board DEM-DAI1753 S/PDIF Receiver 2nd-Order Low-Pass Filter PCM1753/54/55 f-3 dB = 54 kHz or 108 kHz Audio Precision System Two S/PDIF Output Digital Generator 0% Full-Scale, Dither Off (SNR) or -60 dB FS, 1 kHz Sine Wave (Dynamic Range) (1) Results Analyzer and Display Averaging Mode A-Weighting Filter(1) AES17 Filter Band Limit HPF = 400 Hz LPF = 30 kHz f-3 dB = 20.9 kHz without A-Weighting are approximately 3 dB worse. Figure 37. Test Setup for Dynamic Range and SNR Measurement 31 Revision History DATE REV 2/09 C PAGE SECTION 12 System Clock and Reset Functions 14 Audio Serial Interface DESCRIPTION Changed value of 192 kHz at 256 fS from "49.1520" to note "(1)" in Table 1. Changed text. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp PCM1753DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1753DBQG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1753DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1753DBQRG4 ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1754DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1754DBQG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1754DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1754DBQRG4 ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1755DBQ ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1755DBQG4 ACTIVE SSOP DBQ 16 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1755DBQR ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM PCM1755DBQRG4 ACTIVE SSOP DBQ 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF PCM1753, PCM1754 : * Automotive: PCM1753-Q1, PCM1754-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant PCM1753DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 PCM1754DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 PCM1755DBQR SSOP DBQ 16 2000 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) PCM1753DBQR SSOP DBQ 16 2000 367.0 367.0 35.0 PCM1754DBQR SSOP DBQ 16 2000 367.0 367.0 35.0 PCM1755DBQR SSOP DBQ 16 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated