ICS662-03
MDS 662-03 D 1Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
HDTV Audio/Video Clock Source
Description
The ICS662-03 provides synchronous clock generation
for audio sampling clock rates derived from an HDTV
stream. The device uses the latest PLL technology to
provide superior phase noise and long term jitter
performance. The device also supports a 27 MHz
output clock for video MPEG applications from an
HDTV reference clock.
Please contact ICS if you have a requirement for an
input and output frequency not included here.
Features
Packaged in 8-pin SOIC
Available in Pb (lead) free package
HDTV clock input
Low phase noise
Exact (0 ppm) multiplication ratios
Support for 256 and 384 times sampling rate
Supports 27 MHz output for video (MPEG)
Block Diagram
PLL
Clock
Synthesis
CLK
REF_IN
Control
Circuitry
GND
VDD
SEL3:0
HDTV Audio/Video Clock Source
MDS 662-03 D 2Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
ICS662-03
Pin Assignment
8 pin (150 mil) SOIC
Output Clock Selection Table
Pin Descriptions
REF_IN
VDD
GND
S3
S2
S1
CLK
S01
2
3
4
8
7
6
5
S3 S2 S1 S0
Input
Frequency
(MHz)
Output
Frequency
(MHz)
000074.175824 8.192
000174.175824 11.2896
001074.175824 12.288
001174.175824 24.576
010074.175824 16.9344
010174.175824 18.432
011074.175824 36.864
011174.175824 27
1000 74.25 8.192
1001 74.25 11.2896
1010 74.25 12.288
1011 74.25 24.576
1100 74.25 16.9344
1101 74.25 18.432
1110 74.25 36.864
1111 74.25 27
Pin
Number
Pin
Name
Pin
Type Pin Description
1 REF_IN Input Connect this pin to a HDTV clock input.
2 VDD Power Connect to +3.3 V.
3 GND Power Connect to ground.
4 S2 Input Output frequency selection. Determines output frequency per table above. On chip pull-up.
5 CLK Output Clock output.
6 S1 Input Output frequency selection. Determines output frequency per table above. On chip pull-up.
7 S3 Input Output frequency selection. Determines output frequency per table above. On chip pull-up.
8 S0 Input Output frequency selection. Determines output frequency per table above. On chip pull-up.
HDTV Audio/Video Clock Source
MDS 662-03 D 3Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
ICS662-03
Application Information
Series Termination Resistor
Clock output traces should use series termination. To
series terminate a 50 trace (a commonly used trace
impedance), place a 33 resistor in series with the
clock line, as close to the clock output pin as possible.
The nominal impedance of the clock output is 20.
Decoupling Capacitors
As with any high performance mixed-signal IC, the
ICS662-03 must be isolated from system power supply
noise to perform optimally.
Decoupling capacitors of 0.01µF must be connected
between VDD (pin 2) and the PCB ground plane (pin
3).
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) Each 0.01µF decoupling capacitor should be
mounted on the component side of the board as close
to the VDD pin as possible. No vias should be used
between decoupling capacitor and VDD pin. The PCB
trace to VDD pin should be kept as short as possible,
as should the PCB trace to the ground via. Distance of
the ferrite bead and bulk decoupling from the device is
less critical.
2) To minimize EMI and obtain the best signal integrity,
the 33 series termination resistor should be placed
close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers (the ferrite bead and bulk decoupling
capacitor can be mounted on the back). Other signal
traces should be routed away from the ICS662-03. This
includes signal traces just underneath the device, or on
layers adjacent to the ground plane layer used by the
device.
HDTV Audio/Video Clock Source
MDS 662-03 D 4Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
ICS662-03
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS662-03. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
DC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +70°C
Item Rating
Supply Voltage, VDD 5.5 V
All Inputs and Outputs -0.5 V to VDD+0.5 V
Ambient Operating Temperature 0 to +70°C
Storage Temperature -65 to +150°C
Junction Temperature 125°C
Soldering Temperature 260°C
Parameter Min. Typ. Max. Units
Ambient Operating Temperature 0 +70 °C
Power Supply Voltage (measured in respect to GND) +3.0 +3.6 V
Parameter Symbol Conditions Min. Typ. Max. Units
Operating Voltage VDD 3.0 3.3 3.6 V
Supply Current IDD No Load, first 8 modes 25 mA
No Load, last 8 modes 16 mA
Input High Voltage VIH 2V
Input Low Voltage VIL 0.8 V
Output High Voltage VOH IOH = -4 mA VDD-0.4 V
Output High Voltage VOH IOH = -12 mA 2.4 V
Output Low Voltage VOL IOL = 12 mA 0.4 V
Short Circuit Current IOS Each output ±50 mA
Nominal Output Impedance ZOUT 20
Input Capacitance CIN input pins 7 pF
Internal pull-up resistor RPU S2 pin 510 k
S3, S1, S0 pins 120 k
HDTV Audio/Video Clock Source
MDS 662-03 D 5Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
ICS662-03
AC Electrical Characteristics
Unless stated otherwise, VDD = 3.3 V ±10%, Ambient Temperature 0 to +70°C
Thermal Characteristics
Marking Diagram (ICS662M-03) Marking Diagram (ICS662M-03LF)
Notes:
1. ###### is the lot number.
2. YYWW is the last two digits of the year and week that the part was assembled.
3. “LF” denotes Pb (lead) free package.
4. Bottom marking: (origin). Origin = country of origin if not USA.
Parameter Symbol Conditions Min. Typ. Max. Units
Output Clock Rise Time tOR 20% to 80%, 15 pF load 1.2 1.5 ns
Output Clock Fall Time tOF 80% to 20%, 15 pF load 1.0 1.5 ns
Output Duty Cycle tOD at VDD/2, 15 pF load 45 55 %
Jitter, short term tP-P 15 pF load +75 ps
Jitter, long term
27M output, 15 pF load,
first 8 modes,
1000 cycles delay
900 ps
27M output, 15 pF load,
last 8 modes,
1000 cycles delay
600 ps
Frequency Synthesis Error 0 ppm
Parameter Symbol Conditions Min. Typ. Max. Units
Thermal Resistance Junction to
Ambient
θJA Still air 150 °C/W
θJA 1 m/s air flow 140 °C/W
θJA 3 m/s air flow 120 °C/W
Thermal Resistance Junction to Case θJC 40 °C/W
662M-03
######
YYWW$$
14
58
662M03LF
######
YYWW
14
58
HDTV Audio/Video Clock Source
MDS 662-03 D 6Revision 033005
Integrated Circuit Systems, Inc. 525 Race Street, San Jose, CA 95126 tel (408) 295-9800 www.icst.com
ICS662-03
Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body)
Package dimensions are kept current with JEDEC Publication No. 95
Ordering Information
Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS)
assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would
result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial
applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary
environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any
circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or
critical medical instruments.
Part / Order Number Marking Shipping Packaging Package Temperature
ICS662M-03
see page 5
Tubes 8-pin SOIC 0 to +70°C
ICS662M-03TR Tape and Reel 8-pin SOIC 0 to +70°C
ICS662M-03LF Tubes 8-pin SOIC 0 to +70°C
ICS662M-03LFTR Tape and Reel 8-pin SOIC 0 to +70°C
INDEX
AREA
1 2
8
D
E
SEATING
PLANE
A1
A
e
- C -
B
.10 (.004) C
C
L
H
h x 45
Millimeters Inches
Symbol Min Max Min Max
A 1.35 1.75 .0532 .0688
A1 0.10 0.25 .0040 .0098
B 0.33 0.51 .013 .020
C 0.19 0.25 .0075 .0098
D 4.80 5.00 .1890 .1968
E 3.80 4.00 .1497 .1574
e 1.27 BASIC 0.050 BASIC
H 5.80 6.20 .2284 .2440
h 0.25 0.50 .010 .020
L 0.40 1.27 .016 .050
α0°8°0°8°