SPED3/4/5 3.8mm-travel Push-push Type Smooth and linear operation feeling Detector Typical Specifications Items Specifications Slide RatingResistive load 2A 14.5V DC Contact resistance Initial / After operating life 100m max. / 100m max. Operating force 4.170.74N Push Operating lifeWith load SPED3 SPED4 SPED5 30,000 cycles2A 14.5V DC Circuit configuration 1-pole, 2-position Rotary Product Line Power Changeover timing Total travel mm Mounting method Poles Operation Connector Dual-in-line Package Type Non shorting 3.8 PC board 1 Alternate With wire Terminal type Minimum order unitpcs. Product No. Drawing No. 2,500 SPED310200 1 280 1,120 SPED420200 2 240 960 SPED53 3 Japan Export - 500 For PC board - Note If the lead wire length and color are not specified, length (terminal and : 125mm, common terminal: 45mm), color can be specified from black, white, and light green freely. Please consult us for modification. Horizontal Type Packing Specifications Tray Product No. Vertical Type SPED420200 Number of packagespcs. 1 case / Japan 1 case / export packing Export package measurements mm 280 1,120 555x375x223 Bulk Product No. SPED310200 Number of packagespcs. 1 case / Japan 1 case / export packing 500 2,500 Export package measurements mm 400x270x290 SPED53 240 960 Refer to P.130 for soldering conditions. 128 SPED3/4/53.8mm-travel Push-push Type Unit:mm No. Detector Dimensions Reference dimension of connection terminal T=0.5 0.65mm Style Slide 2 58 1.6 Push 4 4 1 Rotary 14 Terminal No.1 Terminal No.C Turnover point Mechanical and Electrical Reset point .7 o11.3 10.11 0.8 4.6 8.5 13.17 1.2 Full stroke point 18.2 Wire length Strip length 8-1 13.5 2 Reset point C 1 o4.7 o4.6 5.5 11.2 o10 1.2 0.8 8.5 7.4 4.8 10.35 20.7 A o5.5 o11.15 o9.7 o3.8 2.6 1.2 4.06 4.06 16.2 Vertical Type 6.2 3.5 3.4 16.97 16.12 14.27 3-1.5 4.06 ole 1h 1.9 3-o Horizontal Type 2.7 13%0.38 ole 6h 3.5 2-o 4.06 2.89 3 13.28 o5.7 2 Turnover point Mechanical and Electrical (t=1.6) Terminal No.2 A o9 Dual-in-line Package Type Full stroke point PC board mounting hole dimensions Viewed from the direction A 4-1 Power 18 6.2 8 Circuit DiagramViewed from direction A C 1 2 Note Factory setting for contact points can be either 1 or 2. 129 Push Switches List of Varieties Vertical Detector Series SPEF SPED2 SPED3 SPED4 SPED5 Photo Slide W 9.4 D 9 16.8 H 6.9 18.3 13.2 13.1 14.3 Travelmm 1.5 -- -- -- -- Total travelmm 2.7 4.5 3.8 Number of poles 1 1 2 1 Dimensions mm Push Rotary Power Operating temperature range Automotive use 14 18 -40 to 85 13.5 18.2 -40 to 95 Dual-in-line Package Type Life cycle Ratingmax. Resistive load 1A 14.5V DC Ratingmin. Resistive load Durability Horizontal Type Vertical Type Electrical performance Operating life without load 50A 3V DC -- -- 2A 14.5V DC -- -- -- -- -- -- -- -- Operating life with load at max. rated load 30,000 cycles 100m max. Initial contact resistance 100m max. Insulation resistance 3M min. 100V DC Voltage proof Terminal strength Mechanical Operating performance Actuator direction strength Pulling direction 3M min. 500V DC 100V AC for 1minute -- -- -- 90N 30N -- Cold Environmental performance Dry heat -- Wire strength 30N 98N 90N 98N -- -- -- -40 96h 85 96h Damp heat Page -- 85 96h (Connector type) 105 192h (Dip type) 105 192h 40, 90 to 95%RH 96h 124 126 128 Push Switches Soldering Conditions 130 Push Switches Cautions 131 Note Indicates applicability to all products in the series. 110 Push Switches / Soldering Conditions Detector Example of Reflow Soldering Condition 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: T hermocouple 0.1 to 0.2 CA (K) or CC (T) at soldering portion (copper foil surface). A heat resisting tape should be used for fixed measurement. 3. Temperature profile Push Temperature (C ) Slide 300 A max. B 200 D E 100 Rotary Room temperature Time (s) Pre-heating F max. C Power Dual-in-line Package Type SeriesReflow type A 3s max. B Cs D E Fs 260 230 40 180 150 120 SPEJ SPEF SPEH Horizontal Type Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Vertical Type Reference for Hand Soldering Series Soldering temperature Soldering time SPPJ3, SPPJ2, SPUN, SPPH4, SPPH1 35010 3+1/0s SPED2, SPED4 35010 30.5s SPEJ 35010 4s max. SPEF 3505 3s max. SPEH 350 max. 3s max. SPUJ 30010 3+1/0s Reference for Dip Soldering (For PC board terminal types) Series 130 For PC board Items Dip soldering Preheating temperature Preheating time Soldering temperature Duration of immersion SPPJ3 100 max. 60s max. 2605 51s SPUN 100 max. 60s max. 2605 101s SPUJ, SPPH4 -- 2605 51s SPPJ2, SPPH1, SPED2, SPED4, SPEF -- 2605 101s