LE365S-41 - AUTONICS - Datasheet.Live

K-87

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

LE365S-41

CONTACT OUT:

250VAC 15A

RESISTIVE LOAD

SOURCE:

100-240VAC

50/60㎐

1 2 3 4

Ordering information

Features

Specications

W48×H48mm, Weekly/Yearly timer

● Easy to check and change the program setting

● Customizable weekly or yearly unit time setting and

control by user

● Includes daylight saving time function

● 1 independent control output.(Relay)

● Flush and surface, DIN rail mounting are in one unit.

Connections

Model LE365S-41

Power supply 100-240VAC 50/60㎐

Allowable voltage range 90 to 110% of rated voltage

Power consumption 2.4VA

Timing program 48 steps for weekly, 24 steps for yearly

Operation mode ON/OFF mode, cycle mode, pulse mode

Mounting Panel ush, surface, DIN rail

Time deviation ±15sec/month(25℃) (±4sec/week)

Temperature error ±0.01% ±0.05sec.

Memory protection Over 5 years(at 25℃)

Control

Output

Contact type SPST(Single Pole Single Throw)

Contact capacity 250VAC 15A resistive load

Output number Independent 1 output(1a)

Relay

life cycle

Mechanical Min. 5,000,000 operations(Switching capacity 30 times/minute)

Electrical 50,000 operations<Switching capacity 20 times/1 minute, at 250VAC 15A(resistive load)>

Insulation resistance Min. 100MΩ(at 500VDC megger)

Dielectric strength 2000VAC 50/60Hz for 1minute

Noise strength ±2kV the square wave noise(pulse width : 1㎲) by the noise simulator

Environ

-ment

Ambient temperature -10 to 55℃, storage: -25 to 65℃

Ambient humidity 35 to 85%RH, storage: 35 to 85%RH

Unit weight Approx. 110g

Item

Size

Power supply

Output

LE365 S 4 1

1 1 Relay outputs

4 100-240VAC

S DIN W48×H48mm

LE365 Weekly/Yearly timer

※Environment resistance is rated at no freezing or condensation.

Please read “Caution for your safety” in operation

manual before using.

K-88

LE365S-41

42.7

66 3

DIN rail

61.5 4

Panel

2-M3 TAP

※Fix the Weekly/Yearly

timer on the panel with

M3 tapping screws.

6.8 60

44.8

① Unscrew 1 bolts

from terminal block

Remove terminals from the body after unscrewing terminals screws, and then assemble terminals to the body after rotating

terminals as shown below.

(front panel mounting)

(surface mounting type) (DIN rail type)

③ Detach terminal

block from case

and rotate it

180˚degree.

② Detach the terminal

block after unscrew

terminal screws with

tools.

※To raise panel holder, tools

must be used.

⑤ Screw terminals block

with a xing bolt.

④ Assemble case

and terminal

block

Dimensions & Mounting

How to switch from the ush mounting to surface or DIN rail mounting type

(unit: mm)

1) Front panel mounting

2) Surface mounting

3) DIN rail mounting

● Panel hole cut-out

Min. 55

Min. 65

● Panel cut-out

45+0.6

K-89

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

Parts description

Functions

413

514

615

19 20 21 22 23

ON Time OFF Time

1. Day indicator

2. Day display

● Light : Day is selected.

● Light-out : Day is not selected.

3. Current time setting mode indicator

4. DST display(Daylight saving time)

5. AM/PM display(Main display)

6. Season display

7. Program display

8. Display ON time/day, OFF time/day, ON time width,

OFF time width

9. AM/PM display(Sub-display)

10. YEAR display

: It turns ON when set, check, modify, delete yearly

program, set yearly holidays and operate yearly

program.

11. Yearly START/STOP day display

12. Main display

13. Remaining step display

14. Operation mode display

15. Output mode display

16. Year, month, date display

17. Unit of pulse width display

18. Sub display

19. CHECK key

20. MODE key

21. Operation key

: Press +1h key over 3sec. in RUN mode, DST mode is

set and released.

22. SET key

23. Output selection switch

● AUTO : Control output according to the set program.

● ON : Output is ON.(Operation)

● OFF : Output is OFF.(Block)

Definitions

● Record: A part of program that controls output operation.

● Step: Basic component of Record.

Operation modes

● If the operation mode of Program1 (program2) is set on

pulse mode initially, the pulse mode is xed for additional

programs. If the operation mode of Program1 (program2)

is set on ON/OFF or cycle mode initially, pulse mode

cannot be used for additional pulse programs.

● If the weekly operation mode is set on ON/OFF or cycle

mode, the yearly operation mode is xed on ON/OFF

mode.

If the yearly operation mode is set on ON/OFF, the

weekly operation mode is xed on ON/OFF or cycle

mode.

● If the weekly operation mode is set on pulse mode, the

yearly operation mode is xed on pulse mode. If the

yearly operation mode is set on pulse mode, the weekly

operation mode is xed on pulse.

●Weekly ON/OFF mode

Output operation by ON/OFF set time.

• Min. time setting unit : 1 min.

• It is able to set ON/OFF day separately.

• One record in two steps

(ON day/ON time, OFF day/OFF time)

●Weekly Cycle operation

It outputs ON the set ON time width which is from Cycle

operation ON time to Cycle operation OFF time, and it

outputs OFF the set OFF time width.

K-90

LE365S-41

ON time

Pulse width

(1 to 59sec., 1 to 60min.)

Weekly setting 1 of Program1

Weekly setting 2 of Program1

Yearly setting 1 of Program1

① ② ③ ④ ⑤ ⑥

Output operation

ON Time ON width OFF Time

OFF width

• Set range for ON/OFF time width

: 1min. to 12 hour 59min.

• One record in 3 steps(ON day/ON time, OFF day/OFF

time, ON time width/OFF time width)

● Weekly pulse mode

Output turns ON at ON time for a specied pulse width.

(Pulse width : 1 to 59sec., 1 to 60min.)

• One record in two steps(ON day/ON time, pulse width)

● Yearly ON/OFF mode

Output turns ON at ON time on START date and turns OFF

at OFF time on STOP date.

• One Record in three Steps(START/STOP date, ON/OFF

time)

● Yearly pulse mode

Output turns ON at ON time on START date and turns

OFF at OFF time on STOP time for a specied pulse width

repeatedly.

• One record in three steps(START/STOP date, ON time,

Pulse width)

Program operation

● ① to ② : Operated by weekly setting 1 of Program 1.

● ② to ③ : Operated by weekly setting 2 of Program 1.

● ④ to ⑤ : Operated by weekly setting 1 of Program 1.

● ⑤ to ⑥ : Operated by yearly setting 1 of Program 1.

(During weekly program operation at 12:00 AM on

START date, the weekly program operation stops, and it

changes to yearly program operation mode. The yearly

program operation stops at 12:00 AM on the next day of

STOP date.)

Display and change of next mode

● The day of next mode in Program is displayed on the day

indicator, and the time of next mode is displayed on the

lower row of screen.

● In ON/OFF operation mode, set ON time and OFF time

to next mode. In Pulse operation mode, set Pulse ON

time to next mode.

Power restore mode

In setting group 2 - LEVEL2 (RET turns ON, AT or NOR

ashes), select Auto[AT] or Normal [NOR] by or key

and press SET key to set.

● Auto [AT] power restore mode

Output operates according to program when power turns

ON again after power failure.

●Normal[NOR] power restore mode

When power turns ON again after power failure, output

is kept OFF and rIN ashes on the lower row of screen

and power restore input (press SET key over 3 sec.

in RUN mode) is applied, rIN turns OFF and output

operates according to program.

Season switching mode

This feature uses for setting seasonal weekly operation

mode. To operate this mode, save starting month and date,

ending month and date of each season which displays S1,

S2, S3, S4 then set day and time of each season in weekly

program setting. It is also able to operate only in summer

and winter season. (S1: set summer season, S2: set winter

season, S3/S4: do not set)

In setting group 2-Level 2(SEN turns ON, OFF ashes.),

select ON[ON] by or key and press SET key to save.

When the season switching mode changed from OFF

to ON or vice versa, previous set programs are deleted.

● ON[ON] mode

Weekly program is switched automatically by season

switching.

• Period setting per season

① Press SET key in period setting per season mode of

setting group 2.(SEN ashes, season with preset period

turns ON and START and STOP turn ON.)

② Advance to the ashing position of season selection

among S1, S2, S3, S4 by or key and press SET

key.

③ After set START month, date per season and press SET

key.

④ SET key is pressed after set STOP month, date per

season, it is advanced to LEVEL1 of period setting per

season. Add or adjust the period setting by SET key.

● It is disable to use when it is OFF [OFF].

● If season terms are overlapped, these are prioritized in

S4>S3>S2>S1 order.

K-91

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

Daylight saving time

To utilize daylight during the summer season, daylight

saving time is adjusted forward one hour from standard

time.

In setting group 2-LEVEL 2(DST turns ON, AT or NOR

ashes), select Auto [AT] or Normal [NOR] by or key

and press SET key to set.

● Auto [AT] daylight saving time mode

Current time will be faster as an hour when it is started and

slower as an hour when it is nished.

• Automatic daylight saving time period setting

① Automatic daylight saving time period setting LEVEL 1

of setting group 2.

(Press SET key when DST ashes and START and

STOP turn ON.)

② Set START date(month, date) of automatic daylight

saving time mode and press SET key.

③ Set START time(AM/PM, hour) of automatic daylight

saving time mode and press SET key. But, the minute

will be xed as 00.

④ Set STOP date(Month, date) of automatic daylight

saving time mode and press SET key.

⑤ Set STOP time(AM/PM, hour) of automatic daylight

saving time mode and press SET key. But, the minute

will be xed as 00.

● Normal [NOR] daylight saving time mode

Press +1h key over 3sec. in RUN mode, "+1h" turns ON

and current time is faster as an hour and "+1h" turns ON

out or vice versa, when press +1h key over 3sec. again.

Current time setting

(Ex) Set the current time as 10, Mar, 2008, 5:10 PM.

● It advances to to "①Current time setting mode" in ON

status and set current time as shown above ② to ④ by

SET key.

● Current time is set up to 31, Dec., 2099.

● Check current year/month/date in RUN mode When

key is pressed over 3sec. in RUN mode, it advances to

current year/month/date display. After display current

year/month/date for 3sec, it returns to RUN mode

displaying current display.

① Advance to the current time setting mode

MODE + SET keys are pressed

over 3sec. in RUN mode, it

is advanced to current time

setting of setting group 2

and clock will be ashed and

tAJ will be lighted in second

display part, press SET key.

SUN MON TUE WED THU FRI SAT

② Year, Month, Date setting

Press or key to set

08 (year 2008) and move

the ashing digit to position

month by key.

Press SET key after pressing

or key to set date 10.

SUN MON TUE WED THU FRI SAT

③ Current time(AM, PM) setting

Press or key to select

PM and move the ashing

digit to position hour by

key.

SUN MON TUE WED THU FRI SAT

④ Current time(hour, min.) setting

Press or key to set 5

PM and move the ashing

digit to position min. by

key. Press or key to set

10min. and press SET key

and it is returned to RUN

mode when pressing MODE

key over 3sec.

SUN MON TUE WED THU FRI SAT

K-92

LE365S-41

RUN mode RUN mode

(Setting group 1)

※1

※2

(Setting group 2)

Weekly program setting mode

( ashes)

Weekly program

setting

Current time setting mode

(Clock icon ashes)

Power failure return selection mode

(RET ashes, ATor NOR turns ON)

Season switching selection mode

(SEN ashes, ON or OFF turns ON)

Period setting for season mode

(SEN ashes, period-set season turns ON and

START or STOP turns ON)

Daylight saving time selection mode

(DST ashes, AT or NOR turns ON)

Automatic[AT] daylight saving

time period setting mode

(DST ashes, START or STOP turns ON)

Current time

setting

Power restore

selection

Season switching

selection

Period setting

per season

Daylight saving

time selection

Automatic

daylight

saving time

period setting

Yearly program setting mode

(, YEAR ashes)

Weekly program delete mode

(, CLR ashes)

Yearly program delete mode

(, CLR, YEAR ashes)

Weekly day change mode

(cDY ashes)

Yearly holiday operation mode

(hDY, YEAR ashes)

Yearly program

setting

All weekly

program delete

All yearly

program delete

Standard day,

change day

setting

Yearly holiday

operation mode

setting

Program setting

LEVEL1 LEVEL1

LEVEL1

LEVEL2 LEVEL2

LEVEL2

LEVEL1 LEVEL2

SET SET

SET

MODE MODE

MODE

Setting group 1 Setting group 2

● When it is advanced to setting group 1 in RUN mode,

output will be OFF.

● It is returned to previous setting group 1 when power of

time switch is ON again in setting group 1.

● When MODE key is pressed in LEVEL2 of setting group

1, current setting will be canceled and it is returned to

previous LEVEL1.

● When press SET key to program over max. number

of steps for weekly program in Weekly program setting

mode of setting group 1-LEVEL 1, number of remaining

steps and STEP ash and it returns to LEVEL 1 status.

● When press SET key to program over max. number of

steps for yearly program in Yearly program setting mode

of setting group 1-LEVEL 1, number of remaining steps

and STEP ash it returns to LEVEL 1 status.

※1: Season switching selection is OFF.

※2: Automatic switching selection of Daylight Saving Time

is Normal[NOR].

● When it advances to setting group 2 in RUN mode,

output (OUT1, OUT2) will be OFF.

● When power of time switch is ON again in setting group 2,

it is returned to previous setting group 1.

● Front MODE key is pressed in LEVEL2 of setting group 2,

it is returned to previous LEVEL1.

● When season switching selection is changed from OFF

to ON or ON to OFF, previous set weekly program will be

deleted.

Press

MODE

key

for 3sec.

Press

MODE

key

for 3sec.

Press

MODE

SET

key for 3sec.

Press

MODE

key

for 3sec.

K-93

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

SUN MON TUE WED THU FRI SAT

8:00

ON for 10sec.

8:00 AM

Example of Weekly program setting

● Weekly ON/OFF mode

(Ex) Output1(OUT1) is ON from Monday to Friday at 8:00

AM and OFF at 6:10 PM.

● Weekly Pulse mode

(Ex) Output2(OUT2) is ON for 10sec at 8:00AM from Mon-

day to Friday during S2 season in case, period of S1, S2,

S3, S4 is set.

8:00

6:10

SUN MON TUE WED THU FRI SAT

① Advance to weekly program setting mode

MODE key is pressed over

3sec in RUN mode P ashes

and press SET key.

SUN MON TUE WED THU FRI SAT

② Mode type setting

Press SET key in ON/OFF

mode.

SUN MON TUE WED THU FRI SAT

④ ON time setting(AM, PM)

key is pressed, move the

ashing to hour position and

select PM by or key

when ON time is afternoon.

③ ON day setting

Press key to move the

indicator to Monday, it will

be lighted when or key

are pressed and move it to

Tuesday by key.

Press SET key after Tuesday,

Wednesday, Thursday,

Friday turn ON.

SUN MON TUE WED THU FRI SAT

⑤ ON time setting(Hour, Min.)

Set 8:00 by or key and

press SET key.

SUN MON TUE WED THU FRI SAT

⑥ OFF day setting

Press SET key to check ON/

OFF day.

SUN MON TUE WED THU FRI SAT

⑦ OFF time setting(AM, PM)

Select PM by or key

and move the ashing to hour

position by key.

SUN MON TUE WED THU FRI SAT

⑨ Complete to set

Press SET key to set

additional program.

SUN MON TUE WED THU FRI SAT

① Advance to weekly program setting mode

MODE key is pressed for

3sec. in RUN mode, P

ashes and press SET key.

SUN MON TUE WED THU FRI SAT

② Mode type setting

Press or key when ON/

OFF ashes, pulse ashes

and press SET key.

SUN MON TUE WED THU FRI SAT

③ Season selection

Press or key to select

season S2 and press SET

key.

SUN MON TUE WED THU FRI SAT

⑧ OFF time setting(Hour, Min.)

SUN MON TUE WED THU FRI SAT

Move the ashing to minute

position by key after set

6:00 by or key and set

the minute as 10 by or

key and press SET key.

K-94

LE365S-41

④ ON day setting

Press key to move the

indicator to Monday, it will be

lighted when or key is

pressed and move it to tuesday

by key. Press

SET

key after

light tuesday, wednesday,

thursday and friday.

SUN MON TUE WED THU FRI SAT

⑤ ON time setting(AM, PM)

Press key, move the

ashing to hour position and

select PM by or key

when ON time is afternoon.

SUN MON TUE WED THU FRI SAT

⑥ ON time setting(Hour, Min.)

Set 8:00 by or key and

press SET key.

SUN MON TUE WED THU FRI SAT

⑦ Pulse width setting

Press or key to select

pulse width as 10s (10sec.)

and press SET key.

SUN MON TUE WED THU FRI SAT

⑧ Complete to set

Press SET key to set

additional program.

SUN MON TUE WED THU FRI SAT

③ to ⑧

Refer to ③ to ⑧ of "Weekly ON/OFF mode" to set ON

day, ON time, OFF day and OFF time.

② Mode type setting

Press or key when ON/

OFF ashes, cycle ashes

and press SET key.

SUN MON TUE WED THU FRI SAT

⑨ ON time width setting

Press key to move the

ashing to minute position

and set as 10min. by or

key and press SET key.

SUN MON TUE WED THU FRI SAT

⑩ OFF time width setting

Press key to move the

ashing to minute position

and set as 5min. by

key and

press SET key.

SUN MON TUE WED THU FRI SAT

⑪ Complete to set

Press

SET

key to set additional

program.

SUN MON TUE WED THU FRI SAT

6:00 AM

Start Cycle mode

5:30

ON for 10min.

OFF for 5min.

● Weekly Cycle mode

(Ex) Output1(OUT1) is ON for 10min and OFF for 5min

from Monday 6:00AM to Saturday 5:30PM.

SUN MON TUE WED THU FRI SAT

① Advance to weekly program setting mode

SUN MON TUE WED THU FRI SAT

In RUN mode, press MODE

key for 3 sec. and P

ashes. Press SET key.

K-95

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

⑤ Complete to yearly holiday

Press MODE key to nish

the additional yearly holiday

setting and press SET key to

set .

※It is able to set yearly

holiday up to 12 times.

SUN MON TUE WED THU FRI SAT

Yearly holiday mode

It operates to off the output without program adjustment

during previously set yearly holiday period available from

present year to 31, Dec. of the next year.

Designate the start date of yearly holiday and year of end

date as every year [--] to repeat the holiday mode for

specied in every year.

● Setting example

Set every year 5, May to off the output.

① Advance to weekly day change mode

Press MODE key over 3sec.

to move to the setting group1

in RUN mode and press it

repeatedly until cDY ashes

in second display part and

press SET key.

SUN MON TUE WED THU FRI SAT

② Standard day selection

Press key to move the

indicator to saturday and

press SET key. after select

saturday as standard day(Sat

turns ON) by or key.

SUN MON TUE WED THU FRI SAT

③ Change day selection

Press key to move the

indicator to monday and

select monday to change

(Monday turns ON) by

or key and repeat the

procedure to select tuesday

to change (Tue turns ON)

and press SET key to

complete.

SUN MON TUE WED THU FRI SAT

① Advance to yearly holiday mode

Press MODE key over 3sec.

to move to the setting group1

in RUN mode and press it

repeatedly until hDY ashes

in second display part and

press SET key.

SUN MON TUE WED THU FRI SAT

② Yearly holiday No. display

Press SET key after check

yearly holiday No.

SUN MON TUE WED THU FRI SAT

③ Start date of yearly holiday setting

Press key until month[--]

position ashes and set May

by or key and press

key until date position

ashes. Press SET key after

set 5th by or key.

SUN MON TUE WED THU FRI SAT

④ End date of yearly holiday setting

The ashing is moved to

month[--] position directly

and press or key to set

May and press key until

date position ashes.

Press SET key after set 5th

by or key.

SUN MON TUE WED THU FRI SAT

Weekly day change

When the specied day mode is required to install in other

day, it is started from the set day and returned to previous

program setting automatically when it is nished.

● Weekly day change cancellation

① Change current year, month, date in current time setting

mode

② Change standard day

③ Delete all program in program

④ Season switching

● Setting example

Output is ON in saturday at 9:00AM and OFF at 12:00PM

and it is ON 8:30AM and OFF at 6:00PM from monday to

friday and the mode of monday and Tuesday is operated

temporarily as saturday(standard) program.

K-96

LE365S-41

2, Oct 3, Oct 4, Oct

8:00

ON for 5sec.

10:00AM

● Yearly pulse mode

(Ex) Output(OUT) is ON from 2, Oct., 2008 to 4,Oct, 2008

at 10:00AM and OFF after 5sec. (Present is 2007.)

④ End date setting

The ashing is moved to

month position directly and

press or key to set April

and press key until date

position ashes. Press SET

key after set 7th by or

key.

SUN MON TUE WED THU FRI SAT

⑤ ON time setting(AM, PM)

key is pressed, move the

ashing to hour position and

select PM by or key

when ON time is afternoon.

SUN MON TUE WED THU FRI SAT

⑥ ON time setting(Hour, Min.)

Press or key to set

9 and press SET key after

check 00min.

SUN MON TUE WED THU FRI SAT

⑦ OFF time setting(AM, PM)

Select PM by or key

and move the ashing to

hour position by key.

SUN MON TUE WED THU FRI SAT

① Advance to yearly program setting mode

MODE key is pressed for 3sec

in RUN mode, P ashes and

press MODE key again, P

ashes and press SET key.

SUN MON TUE WED THU FRI SAT

② Mode type setting

or key is pressed when

ON/OFF ashes to set pulse

mode and press SET key.

SUN MON TUE WED THU FRI SAT

③ Start date setting

Press or key twice to

set 08(year 2008) and move

to month position by key.

Set Oct. by or key and

move to date position by

key and press SET key after

set 2nd by or key.

SUN MON TUE WED THU FRI SAT

④ End date setting

The ashing is moved to

month position directly by

key and set 4th by or

key after move it to date

position by key, then press

SET key.

SUN MON TUE WED THU FRI SAT

Yearly program setting

● Yearly ON/OFF mode

(Ex) Output(OUT) is ON from every 5, Apr to 7, Apr at

9:00AM and OFF 5:10PM.

①

Advance to Program1(P1) yearly program setting mode

Press MODE key for 3 sec.

RUN mode,

ashes

and

press MODE key once, then,

P and YEAR ash and press

SET key to set.

SUN MON TUE WED THU FRI SAT

② Mode type setting

Press

SET

key when ON/OFF

ashes.

SUN MON TUE WED THU FRI SAT

③ Start date setting

Press key until month

position ashes and set Apr

by or key and press

key until date position

ashes. Press SET key after

set 5th by or key.

SUN MON TUE WED THU FRI SAT

⑨ Complete to set

Press SET key to set

additional program.

SUN MON TUE WED THU FRI SAT

⑧ OFF time setting(Hour, Min.)

SUN MON TUE WED THU FRI SAT

Move the ashing to minute

position after set 5:00 by

or key and set the minute

as 10 and press SET key.

K-97

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Weekly/Yearly Timer

RUN mode

Weekly program

record No.1[r01]

setting check

Weekly program

record No.1[r01] setting

modify and delete

Weekly program

record No.2[r02] setting

modify and delete

Weekly program

record No.n[rN] setting

modify and delete

Weekly program

record No.2[r02]

setting check

Weekly program

record No.n[rN]

setting check

Program check, modify and delete

CHECK

Weekly program check, modify and delete

Press CHECK

key for 1sec.

Press

MODE

key

for 3sec.

Press SET

key for 1sec.

Press SET

key for 3sec.

Press SET

key for 3sec.

RUN mode

Yearly program

record No.1[r01]

setting check

Yearly program

record No.1[r01] setting

modify and delete

Yearly program

record No.2[r02] setting

modify and delete

Yearly program

record No.n[rN] setting

modify and delete

Yearly program

record No.2[r02]

setting check

Yearly program

record No.n[rN]

setting check

CHECK

Yearly program check, modify and delete

※YEAR turns ON when check, modify or delete yearly

program.

● If any key is untouched for 60sec., it is returned to RUN

mode in weekly or yearly program check.

● In weekly or yearly program check, it controls output

according to program setting and output is OFF in modify

or delete mode.

● When MODE key is pressed in weekly or yearly program

record modify, delete stand by or delete mode, current

work is cancelled and it is returned to check mode.

● Weekly or yearly program record modify and delete

(1) Program record modify

① When press SET key over 3sec. in program check, EDT

ashes in second display part, press SET key.

② It returns to check mode when nish the modify same

as the above procedure.

(2) Program record delete

① When press SET key over 3sec. in program check, EDT

ashes in second display part, press or key until

CLR ashes in second display part and press SET key.

② Press CLR key over 3sec. when SET turns ON in

second display part, it returns to program check.

Press SET

key for 3sec.

Press SET

key for 3sec.

Press SET

key for 3sec.

Press CHECK

key for 1sec.

Press

MODE

key

for 3sec.

※It is able to set year of start/end date in yearly program

setting up to 2 years later from the present year.

⑤ ON time setting(AM, PM)

key is pressed, move the

ashing to hour position and

select PM by or key

when ON time is afternoon.

SUN MON TUE WED THU FRI SAT

⑥ ON time setting(Hour, Min.)

Press or key twice to

set 10 and press SET key

after check 00min.

SUN MON TUE WED THU FRI SAT

⑦ Pulse width setting

Press or key 4 times to

select pulse width as 5s and

press SET key.

SUN MON TUE WED THU FRI SAT

⑧ Complete to set

Press SET key to set

additional program.

SUN MON TUE WED THU FRI SAT