UB800-18GM40-E5-V1 - PEPPERL+FUCHS

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com

Ultrasonic sensor UB800-18GM40-E5-V1

Release date: 2009-11-26 15:57 Date of issue: 2009-11-26 205343_ENG.xml

Model Number

UB800-18GM40-E5-V1

Single head system

Features

• Short design, 40 mm

• Function indicators visible from all

directions

• Switch output

• 5 output modes

• Program input

• Temperature compensation

Curves

Characteristic response curve

Distance X [mm]

Distance Y [mm]

Curve 1: flat surface 100 mm x 100 mm

Curve 2: round bar, Ø 25 mm

0 200 400 600 800 1000 1200 1400

200

150

100

-50

-100

-150

-200

Technical data

General specifications

Sensing range 50 ... 800 mm

Adjustment range 70 ... 800 mm

Unusable area 0 ... 50 mm

Standard target plate 100 mm x 100 mm

Transducer frequency approx. 255 kHz

Response delay approx. 100 ms

Indicators/operating means

LED green Power on

LED yellow indication of the switching state

flashing: program function object detected

LED red permanently red: Error

red, flashing: program function, object not detected

Electrical specifications

Operating voltage UB10 ... 30 V DC , ripple 10 %SS

No-load supply current I0≤ 20 mA

Input

Input type 1 program input

operating distance 1: -UB ... +1 V, operating distance 2: +6 V

... +UB

input impedance: > 4,7 kΩ program pulse: ≥ 1 s

Output

Output type 1 switch output E5, pnp NO/NC, programmable

Rated operational current Ie200 mA , short-circuit/overload protected

Default setting Switch point A1: 70 mm Switch point A2: 800 mm

Voltage drop Ud≤ 3 V

Repeat accuracy ≤ 1 %

Switching frequency f ≤ 4 Hz

Range hysteresis H 1 % of the set operating distance

Temperature influence ± 1.5 % of full-scale value

Ambient conditions

Ambient temperature -25 ... 70 °C (248 ... 343 K)

Storage temperature -40 ... 85 °C (233 ... 358 K)

Mechanical specifications

Protection degree IP67

Connection V1 connector (M12 x 1), 4-pin

Material

Housing brass, nickel-plated

Transducer epoxy resin/hollow glass sphere mixture; foam

polyurethane, cover PBT

Mass 25 g

Compliance with standards and

directives

Standard conformity

Standards EN 60947-5-2:2007

IEC 60947-5-2:2007

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com

Ultrasonic sensor UB800-18GM40-E5-V1

Release date: 2009-11-26 15:57 Date of issue: 2009-11-26 205343_ENG.xml

Adjusting the switching points

The ultrasonic sensor features a switch output with two teachable switching points.

These are set by applying the supply voltage -UB or +UB to the TEACH-IN input. The

supply voltage must be applied to the TEACH-IN input for at least 1 s. LEDs indicate

whether the sensor has recognised the target during the TEACH-IN procedure. Swit-

ching point A1 is taught with -UB, A2 with +UB.

Five different output functions can be set

1. Window mode, normally-open function

2. Window mode, normally-closed function

3. one switching point, normally-open function

4. one switching point, normally-closed function

5. Detection of object presence

TEACH-IN window mode, normally-open function

• Set target to near switching point

• TEACH-IN switching point A1 with -UB

• Set target to far switching point

• TEACH-IN switching point A2 with +UB

TEACH-IN window mode, normally-closed function

• Set target to near switching point

• TEACH-IN switching point A2 with +UB

Dimensions

Electrical Connection

Pinout

24.5

39.2

50.2

M12 x 1

M18 x 1

LED

3 (BU)

1 (BN)

2 (WH)

4 (BK)

+ U

Teach input

Switch output

- U

Core colours in accordance with EN 60947-5-2.

Standard symbol/Connections:

(version E5, pnp)

Connector V1

Additional Information

Accessories

UB-PROG2

Programming unit

OMH-04

Mounting aid

BF 18

Mounting flange

BF 18-F

Mounting flange

BF 5-30

Mounting flange

V1-G-2M-PVC

Cable connector

V1-W-2M-PUR

Cable connector

Programmable output modes

1. Window mode, normally open mode

A1 < A2:

2. Window mode, normally closed mode

A2 < A1:

3. One switch point, normally open mode

A1 -> ∞

5. A1 -> ∞, A2 -> ∞: Object presence detection mode

Object detected: Switch output closed

No object detected: Switch output open

4. One switch point, normally closed mode

A2 -> ∞:

object distance

A1 A2

A2 A1

Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany

Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091 • Internet http://www.pepperl-fuchs.com

Ultrasonic sensor UB800-18GM40-E5-V1

Release date: 2009-11-26 15:57 Date of issue: 2009-11-26 205343_ENG.xml

• Set target to far switching point

• TEACH-IN switching point A1 with -UB

TEACH-IN switching point, normally-open function

• Set target to near switching point

• TEACH-IN switching point A2 with +UB

• Cover sensor with hand or remove all objects from sensing range

• TEACH-IN switching point A1 with -UB

TEACH-IN switching point, normally-closed function

• Set target to near switching point

• TEACH-IN switching point A1 with -UB

• Cover sensor with hand or remove all objects from sensing range

• TEACH-IN switching point A2 with +UB

TEACH-IN detection of objects presence

• Cover sensor with hand or remove all objects from sensing range

• TEACH-IN switching point A1 with -UB

• TEACH-IN switching point A2 with +UB

Default setting of switching points

A1 = blind range, A2 = nominal distance

LED Displays

Installation conditions

If the sensor is installed at places, where the environment temperature can fall below 0 °C, for the sensors fixation, one of the

mounting flanges BF18, BF18-F or BF 5-30 must be used.

In case of direct mounting of the sensor in a through hole using the steel nuts, it has to be fixed at the middle of the housing

thread. If a fixation at the front end of the threaded housing is required, plastic nuts with centering ring (accessories) must be

used.

Displays in dependence on operating mode Red LED Yellow LED

TEACH-IN switching point:

Object detected

No object detected

Object uncertain (TEACH-IN invalid)

off

flashes

off

Normal operation off Switching state

Fault on Previous state