Integrated Circuit Systems, Inc. ICS9159-14 Frequency Generator and Integrated Buffer for PENTIUMTM General Description Features The ICS9159-14 generates all clocks required for high speed RISC or CISC microprocessor systems such as 486, Pentium, PowerPC,O etc. Four different reference frequency multiplying factors are externally selectable with smooth frequency transitions. These multiplying factors can be customized for specific applications. * Generates up to four processor and six bus clocks, plus disk, USB and reference clocks * Synchronous clocks skew matched to 250ps window on PCLKs and 500ps window on BCLKs * 3.0V - 5.5V supply range High drive BCLK outputs provide typically greater than 1V/ ns slew rate into 30pF loads. PCLK outputs provide typically better than 1V/ns slew rate into 20pF loads while maintaining 5% duty cycle. * 28-pin SOIC package Block Diagram Pin Configuration 28-Pin SOIC Functionality FS1 FS0 0 0 *VCO X1, REF (MHz) CPU (MHz) 14.318 50 (49.7) 0 1 118/17 x X1 65/7 x X1 14.318 66.6 (66.5) 1 0 92/11 x X1 14.318 60 (59.9) 1 1 69/9 x X1 14.318 55 (54.9) *VCO range is limited from 60 - 200 MHz. PCLK(0:3) BCLK(0:5) USB DISK VCO/2 PCLK/2 48 MHz 24 MHz All frequencies in MHz, assuming 14.318 MHz input. Pentium is a trademark of Intel Corporation. PowerPC is a trademark of Motorola Corporation. ICS9159-14 Rev B 3/16/00 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate. ICS9159-14 Pin Descriptions PIN NUMBER PIN NAME TYPE DESCRIPTION 1, 8, 26 VDD PWR 2 X1 IN 3 X2 OUT XTAL output which includes XTAL load capacitance. 4, 11, 23 GND PWR Ground for logic, CPU and fixed frequency output buffers. 6, 7, 9, 10 PCLK(0:3) OUT 13, 12 FS(0:1) IN Power for logic, CPU and fixed frequency output buffers. XTAL or external reference frequency input. This input includes XTAL load capacitance and feedback bias for a 12 - 16 MHz crystal, nominally 14.31818 MHz. Processor clock outputs which are a multiple of the input reference frequency as shown in the table above. Frequency multiplier select pins. See table above. These inputs have internal pull-up devices. 14, 20 VDD PWR Power for BCLK output buffers. 15, 16, 18 19, 21, 22 BCLK(0:5) OUT Bus clock outputs are fixed at one half the PCLK frequency. 17 GND PWR Ground for BCLK output buffers. 5 OEN IN 25 USB OUT The USB clock is fixed at 48 MHz (with 14.318 MHz input). 28, 27 REF(0:1) OUT REF is a buffered copy of the crystal oscillator or reference input clock, nominally 14.31818 MHz. OEN tristates all outputs when low. This input has an internal pull-up device. 24 DISK OUT The DISK controller clock is fixed at 24 MHz (with 14.318 MHz input). 2 ICS9159-14 Absolute Maximum Ratings Supply Voltage .......................................................................................................... 7.0 V Logic Inputs ....................................................................... GND -0.5 V to VDD +0.5 V Ambient Operating Temperature ............................................................. 0C to +70C Storage Temperature ........................................................................... -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics at 3.3V VDD = 3.0 - 3.7 V, TA = 0 - 70 C unless otherwise stated DC Characteristics PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Input Low Voltage VIL - - 0.2VDD V Input High Voltage VIH 0.7VDD - - V Input Low Current IIL VIN=0V -28.0 -10.5 - mA Input High Current IIH VIN=VDD -5.0 - 5.0 mA Output Low Current1 IOL VOL=0.8V; for CPUs & BUSes 30.0 47.0 - mA Output High Current1 IOH VOH=2.0V; for CPUs & BUSes - -66.0 -42.0 mA Output Low Current1 IOL VOL=0.8V; for fixed CLKs 25.0 38.0 - mA Output High Current1 IOH VOH=2.0V; for fixed CLKs - -47.0 -30.0 mA VOL IOL=15mA; for CPUs & BUSes - 0.3 0.4 V VOH IOH=-30mA; for CPUs & BUSes 2.4 2.8 - V VOL IOL=12.5mA; for fixed CLKs - 0.3 0.4 V Output High Voltage1 VOH IOH=-20mA; for fixed CLKs 2.4 2.8 - V Supply Current IDD @66.5 MHz; all outputs unloaded - 55 110 mA Output Low Voltage 1 Output High Voltage1 Output Low Voltage 1 Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 3 ICS9159-14 Electrical Characteristics at 3.3V VDD = 3.1 - 3.7 V, TA = 0 - 70 C AC Characteristics PARAMETER Rise Time 1 Fall Time1 1 Rise Time 1 Fall Time 1 Duty Cycle SYMBOL Input Frequency 1 - 0.9 1.5 ns - 0.8 1.4 ns Tr2 20pF load, 20% to 80% CPU & BUS - 1.5 2.5 ns Tf2 20pF load, 80% to 20% CPU & BUS - 1.4 2.4 ns Dt 45 50 55 % - 50 150 ps -250 - 250 ps Tj1s2 20pF load @ VOUT=1.4V CPU & BUS Clocks; Load=20pF, FOUT>25 MHz CPU & BUS Clocks; Load=20pF, FOUT>25 MHz Fixed CLK; Load=20pF - 1 3 % Tjab2 Fixed CLK; Load=20pF -5 2 5 % Fi Logic Input Capacitance1 Crystal Oscillator Capacitance1 UNITS 20pF load, 2.0 to 0.8V CPU & BUS Tjab1 Jitter, Absolute MAX 20pF load, 0.8 to 2.0V CPU & BUS Jitter, Absolute1 1 TYP Tf1 Tj1s1 Jitter, One Sigma MIN Tr1 Jitter, One Sigma1 1 TEST CONDITIONS CIN 14.318 16.0 MHz - 5 - pF - 18 - pF - 2.5 4.5 ms - 2.0 4.0 ms - 150 250 ps Clock Skew Window1 Tsk1 X1, X2 pins From VDD=1.6V to 1 st crossing of 66.5 MHz VDD supply ramp < 40ms From 1st crossing of acquisition to < 1% settling CPU to CPU; Load=20pF; @1.4V Clock Skew Window1 Tsk2 BUS to BUS; Load=20pF; @1.4V - 300 500 ps 1 Tsk3 CPU to BUS; Load=20pF; @1.4V 1 2.6 5 ns Power-on Time1 ton Frequency Settling Time1 Clock Skew Window CINX 12.0 Logic input pins ts Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 4 ICS9159-14 Electrical Characteristics at 5.0V VDD = 4.5 - 5.5 V, TA = 0 - 70 C DC Characteristics PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Input Low Voltage VIL - - 0.8 V Input High Voltage VIH 2.4 - - V Input Low Current IIL VIN=0V -45 -15 - A Input High Current IIH VIN=VDD -5.0 - 5.0 A Output Low Current1 IOL VOL=0.8V; for CPUs & BUSes 36.0 62.0 - mA Output High Current1 IOH VOL=2.0V; for CPUs & BUSes - -152 -90.0 mA Output Low Current1 IOL VOL=0.8V; for fixed CLKs 30.0 50.0 - mA Output High Current1 IOH VOL=2.0V; for fixed CLKs - -110.0 -65.0 mA Output Low Voltage1 VOL IOL=20mA; for CPUs & BUSes - 0.25 0.4 V Output High Voltage1 VOH IOH=-70mA; for CPUs & BUSes 2.4 4.0 - V Output Low Voltage VOL IOL=15mA; for fixed CLKs - 0.2 0.4 V Output High Voltage1 VOH IOH=-50mA; for fixed CLKs 2.4 4.7 - V Supply Current IDD @66.5 MHz; all outputs unloaded - 80.0 160.0 mA 1 Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 5 ICS9159-14 Electrical Characteristics at 5.5V VDD = 4.5 - 5.5 V, TA = 0 - 70 C AC Characteristics PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Rise Time1 Tr1 20pF load, 0.8 to 2.0V CPU & BUS - 0.55 0.95 ns Fall Time1 Tf1 20pF load, 2.0 to 0.8V CPU & BUS - 0.52 0.90 ns Rise Time1 Tr2 20pF load, 20% to 80%CPU & BUS - 1.2 2.1 ns Fall Time1 Tf2 20pF load, 80% to 20% CPU & BUS - 1.1 2.0 ns Duty Cycle1 Dt1 20pF load @ VOUT=1.4V 52 57 62 % Duty Cycle1 Dt2 20pF load @ VOUT=50% 45 50 55 % - 50 150 ps -250 - 250 ps CPU & BUS Clocks; Load=20pF, RS=33W FOUT>25 MHz CPU & BUS Clocks; Load=20pF, RS=33W FOUT>25 MHz Jitter, One Sigma1 Tj1s1 Jitter, Absolute1 Tjab1 Jitter, One Sigma1 Tj1s2 REF CLKs; Load=20pF RS=33W - 1 3 % Jitter, Absolute1 Tjab2 REF CLKs; Load=20pF RS=33W -5 2 5 % 12.0 14.318 16.0 MHz Logic input pins - 5 - pF X1, X2 pins - 18 - pF - 2.5 4.5 ms - 2.0 4.0 ms 1 Input Frequency Fi Logic Input Capacitance1 CIN 1 Crystal OscillatorCapacitance CINX Power-on Time1 ton Frequency Settling Time1 ts From VDD=1.6V to 1 st crossing of 66.5 MHz VDD supply ramp < 40ms From 1st crossing of acquisition to < 1% settling Clock Skew Window1 Tsk1 CPU to CPU; Load=20pF; @1.4V - 150 250 ps Clock Skew Window1 Tsk2 BUS to BUS; Load=20pF; @1.4V - 300 500 ps 1 Tsk3 CPU & BUS; Load=20pF; @1.4V 1 2.6 5 ns Clock Skew Window Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 6 ICS9159-14 LEAD COUNT 28L DIMENSIONL 0.704 SOIC Package Ordering Information ICS9159M-14 Example: ICS XXXX M-PPP Pattern Number(2 or 3 digit number for parts with ROM code patterns) Package Type M=SOIC, SOP Device Type (consists of 3 or 4 digit numbers) plus one additional Alph designation Prefix ICS=Standard Device 7 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.