MICROCIRCUIT DATA SHEET Original Creation Date: 08/02/95 Last Update Date: 02/17/97 Last Major Revision Date: 08/02/95 MNLM555-X REV 0B0 PRECISION TIMER General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the time delay mode of operation, the time is precisely controlled by one external resistor and capacitor. For astable operation as an oscillator, the free running frequency and duty cycle are accurately controlled with two external resistors and one capacitor. The circuit may be triggered and reset on falling waveforms, and the output circuit can source or sink up to 200mA or drive TTL circuits. Industry Part Number NS Part Numbers LM555 LM555H/883 LM555J/883 Prime Die LM555 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNLM555-X REV 0B0 Features - Direct replacement for SE555/NE555 Timing from microseconds through hours Operates in both astable and monostable modes Adjustable duty cycle Output can source or sink 200mA Output and supply TTL compatible Temperature stability better than 0.005% per degrees C Normally on and normally off output Applications - Precision timing Pulse generation Sequential timing Time delay generation Pulse width modulation Pulse position modulation Linear ramp generator 2 MICROCIRCUIT DATA SHEET MNLM555-X REV 0B0 (Absolute Maximum Ratings) (Note 1) Supply Voltage +18V Power Dissipation (Note 2) LM555H LM555J Operating Temperature Range 760 mW 1180mW -55 C to +125 C Maximum Junction Temperature 150 C Storage Temperature Range -65 C to +150 C Soldering Information Dual-In-Line Package (Soldering, 10 seconds) Thermal Resistance ThetaJA CERDIP (Still Air) (500LF/Min Air flow) METAL CAN (Still Air) (500LF/Min Air flow) 260 C 125 71 176 96 ThetaJC CERDIP METAL CAN ESD Tolerance (Note 3) C/W C/W C/W C/W 20 C/W 42 C/W 500V Note 1: Note 2: Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 1.5K Ohms in series with 100pF. 3 MICROCIRCUIT DATA SHEET MNLM555-X REV 0B0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +5V <= Vcc <= +15V SYMBOL IccL PARAMETER Supply Current Low State CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vcc = 5V, RL = Infinity 5.0 mA 1 Vcc = 15V, RL = Infinity 12.0 mA 1 Vcc = 18V, RL = Infinity, V2 = V6 = 18V 18.5 mA 1 IL7 Leakage Current Pin 7 Vcc = 18V, V7 = 18V, V2 = V6 = 0 100 nA 1 Vsat Saturation Voltage Pin 7 Vcc = 15V, I7 = 15mA, V2=V6=12V 240 mV 1 Vcc = 4.5V, I7 = 4.5mA 80 mV 1 Vco Control Voltage Vcc = 5V, V2 = V6 = 4V 2.9 3.8 V 1, 2, 3 Vcc = 15V, V2 = V6 = 12V 9.6 10.4 V 1, 2, 3 9.5 10.5 V 1 Vth Threshold Voltage Ith Threshold Current V6 = VTH, V2 = 7.5V, VTH = T17 Reading 250 nA 1 ITRIG Trigger Current V2 = 0 500 nA 1 VTRIG Trigger Voltage Vcc = 15V 4.8 5.2 V 1 3.0 6.0 V 2, 3 1.45 1.9 V 1, 2, 3 0.4 mA 1 1.0 V 1 Vcc = 5V, Isink = +8mA, V7=5V, V6=5V 250 mV 1, 2, 3 Vcc = 15V, Isink = +10mA, V2=V6=15V 150 mV 1 250 mV 2, 3 500 mV 1 800 mV 2, 3 2.2 V 1, 2, 3 13 V 1 12.75 V 2, 3 3 V 1 2.75 V 2, 3 Vcc = 5V Ireset Reset Current Vreset Reset Voltage Vol Output Voltage Drop Low 1 V2 = V6 = GND 0.4 Vcc = 15V, Isink = +50mA, V2=V6=15V Vcc = 15V, Isink = +85mA, V2=V6=15V Voh Output Voltage Drop High Vcc = 15V, Isource = 85mA Vcc = 5V, Isource = 85mA 4 MICROCIRCUIT DATA SHEET MNLM555-X REV 0B0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +5V <= Vcc <= +15V SYMBOL PARAMETER AFREQ A Stable Frequency Et Timing Error Delta Et/ Delta Vcc Timing Drift with Supply CONDITIONS NOTES 2 PINNAME MIN 45 MAX UNIT SUBGROUPS 51 KHz 1 Vcc = 5V 2 +2 % 1, 2, 3 Vcc = 15V, 1K<=RA<=100K, (Timing error decreases with an increase in Vcc) 2 +2 % 1, 2, 3 5V <= Vcc <= 15V 2 0.2 %/V 1, 2, 3 AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: +5V <= Vcc <= +15V tR tF Rise Time Fall Time VTRIG = 5V VTRIG = 5V 2 250 nS 9, 10 2 400 nS 11 2 250 nS 9, 10 2 400 nS 11 DC PARAMETERS: DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +5V <= Vcc <= +15V. "Delta not required on B-Level product. Deltas required for S-Level product ONLY as specified on Internal Processing Instructions (IPI)". Vco Vol Voh Control Voltage Output Voltage Drop Low Output Voltage Drop High Note 1: Note 2: Vcc = 5V, V2=V6=4V -0.1 0.1 V 1 Vcc = 15V, V2=V6=12V -0.1 0.1 V 1 Vcc = 15V, Isink = +10mA, V2=V6=15V -50 50 mV 1 Vcc = 15V, Isink = +50mA, V2=V6=15V -50 50 mV 1 Vcc = 15V, Isource = 85mA -0.26 0.26 V 1 Guaranteed by tests at Vcc = 15V. Guaranteed parameter , Not tested. 5 MICROCIRCUIT DATA SHEET MNLM555-X REV 0B0 Graphics and Diagrams GRAPHICS# DESCRIPTION H08CRE (blank) J08ARL CERDIP (J), 8 LEAD (P/P DWG) See attached graphics following this page. 6