Sample & Buy Product Folder Support & Community Tools & Software Technical Documents LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 LMZ22003 3-A SIMPLE SWITCHER(R) Power Module With 20-V Maximum Input Voltage 1 Features 2 Applications * * * * * * 1 * * * * * * * * * Integrated Shielded Inductor Simple PCB Layout Frequency Synchronization Input (650 kHz to 950 kHz) Flexible Start-up Sequencing Using External SoftStart, Tracking and Precision Enable Protection Against Inrush Currents and Faults such as Input UVLO and Output Short Circuit Junction Temperature Range -40C to 125C Single Exposed Pad and Standard Pinout for Easy Mounting and Manufacturing Fast Transient Response for Powering FPGAs and ASICs Fully Enabled for WEBENCH(R) Power Designer Pin Compatible With LMZ23605/LMZ23603/LMZ22005 Electrical Specifications - 18-W Maximum Total Output Power - Up to 3-A Output Current - Input Voltage Range 6 V to 20 V - Output Voltage Range 0.8 V to 6 V - Efficiency up to 92% Performance Benefits - High Efficiency Reduces System Heat Generation - Tested To EN55022 Class B(1) - Low Component Count, Only 5 External Components - Low Output Voltage Ripple - Uses PCB as Heat Sink, No Airflow Required * Point-of-load Conversions from 12-V Input Rail Time-Critical Projects Space Constrained and High Thermal Requirement Applications Negative Output Voltage Applications (See AN-2027 SNVA425) 3 Description The LMZ22003 SIMPLE SWITCHER(R) power module is an easy-to-use step-down DC-DC solution capable of driving up to 3-A load. The LMZ22003 is available in an innovative package that enhances thermal performance and allows for hand or machine soldering. The LMZ22003 can accept an input voltage rail between 6 V and 20 V and can deliver an adjustable and highly accurate output voltage as low as 0.8 V. The LMZ22003 only requires two external resistors and three external capacitors to complete the power solution. The LMZ22003 is a reliable and robust design with the following protection features: thermal shutdown, programmable input undervoltage lockout, output overvoltage protection, short circuit protection, output current limit, and this device allows start-up into a prebiased output. The sync input allows synchronization over the 650- to 950-kHz switching frequency range. Device Information(1)(2) PART NUMBER PACKAGE LMZ22003 NDW (7) BODY SIZE (NOM) 10.16 mm x 9.85 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. (2) Peak reflow temperature equals 245C. See SNAA214 for more details. NOTE: EN 55022:2006, +A1:2007, FCC Part 15 Subpart B: 2007. See AN-2125 SNVA473 and layout for information on device under test. Vin = 12 V, Vo = 3.3 V, Io = 3 A Simplified Application Schematic Efficiency 5-V Output at 25C Ambient 100 VOUT @ 3A RFBT See Table CIN 22 PF Enable CSS 0.47 PF RFBB See Table Co 220 PF EFFICIENCY (%) 90 VOUT SS/TRK FB PGND EN AGND VIN VIN SYNC LMZ22003 80 70 60 50 9 VIn 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 3 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 3 4 4 4 4 6 Absolute Maximum Ratings ...................................... ESD Ratings ............................................................ Recommended Operating Conditions....................... Thermal Information ................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 14 7.1 7.2 7.3 7.4 Overview ................................................................. Functional Block Diagram ....................................... Feature Description................................................. Device Functional Modes........................................ 14 14 14 16 8 Application and Implementation ........................ 17 8.1 Application Information............................................ 17 8.2 Typical Application ................................................. 17 9 Power Supply Recommendations...................... 22 10 Layout................................................................... 23 10.1 10.2 10.3 10.4 Layout Guidelines ................................................. Layout Examples................................................... Power Dissipation and Thermal Considerations ... Power Module SMT Guidelines ............................ 23 23 24 25 11 Device and Documentation Support ................. 26 11.1 11.2 11.3 11.4 11.5 11.6 Device Support...................................................... Documentation Support ........................................ Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 26 26 26 26 26 26 12 Mechanical, Packaging, and Orderable Information ........................................................... 27 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision H (October 2013) to Revision I * Page Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ................................................................................................ 1 Changes from Revision G (March 2013) to Revision H Page * Deleted 10 mil......................................................................................................................................................................... 4 * Changed 10 mil .................................................................................................................................................................... 25 * Added Power Module SMT Guidelines................................................................................................................................. 25 2 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 5 Pin Configuration and Functions NDW Package 7-Pin Top View PGND/EP Connect to AGND VOUT SS/TRK FB AGND EN SYNC VIN 7 6 5 4 3 2 1 Pin Functions PIN NAME NO. TYPE DESCRIPTION AGND 4 Ground Analog Ground -- Reference point for all stated voltages. Must be externally connected to PGND (EP). EN 3 Analog Enable -- Input to the precision enable comparator. Rising threshold is 1.279 V typical. Once the module is enabled, a 21-A source current is internally activated to facilitate programmable hysteresis. FB 5 Analog Feedback -- Internally connected to the regulation amplifier, overvoltage comparators. The regulation reference point is 0.796 V at this input pin. Connect the feedback resistor divider between the output and AGND to set the output voltage. PGND -- Ground Exposed Pad / Power Ground Electrical path for the power circuits within the module. -- NOT Internally connected to AGND / pin 4. Used to dissipate heat from the package during operation. Must be electrically connected to pin 4 external to the package. SS/TRK 6 Analog Soft-Start/Track -- To extend the 1.6-ms internal soft-start connect an external soft-start capacitor. For tracking connect to an external resistive divider connected to a higher priority supply rail. See Design Steps section SYNC 2 Analog Sync Input -- Apply a CMOS logic level square wave whose frequency is between 650 kHz and 950 kHz to synchronize the PWM operating frequency to an external frequency source. When not using synchronization connect to ground. The module free-running PWM frequency is 812 kHz (typical). VIN 1 Power Supply input -- Nominal operating range is 6 V to 20 V. A small amount of internal capacitance is contained within the package assembly. Additional external input capacitance is required between this pin and exposed pad (PGND). VOUT 7 Power Output Voltage -- Output from the internal inductor. Connect the output capacitor between this pin and exposed pad. 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) (3) MIN MAX UNIT VIN to PGND -0.3 24 V EN, SYNC to AGND -0.3 5.5 V SS/TRK, FB to AGND -0.3 2.5 V AGND to PGND -0.3 0.3 V 150 C 245 C 150 C Junction temperature Peak reflow case temperature (30 sec) Storage temperature, Tstg (1) (2) (3) -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. For soldering specifications, refer to the following document: SNOA549 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 3 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) VALUE UNIT 2000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN MAX VIN 6 20 V EN, SYNC 0 5 V -40 125 C Operation junction temperature UNIT 6.4 Thermal Information LMZ22003 THERMAL METRIC (1) NDW UNIT 7 PINS Junction-to-ambient thermal resistance (2) RJA RJC(top) (1) (2) Junction-to-case (top) thermal resistance 4-layer Evaluation Printed-Circuit-Board, 60 vias, No air flow 12.0 2-layer JEDEC Printed-Circuit-Board, No air flow 21.5 No air flow 1.9 C/W C/W For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. RJA measured on a 3.5-in x 3.5-in 4-layer board, with 3-oz. copper on outer layers and 2-oz. copper on inner layers, sixty thermal vias, no air flow, and 1-W power dissipation. Refer to application note layout diagrams. 6.5 Electrical Characteristics Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 12 V, VOUT = 3.3 V. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT SYSTEM PARAMETERS ENABLE CONTROL VEN EN threshold trip point VEN-HYS EN input hysteresis current VEN rising, TJ = 25C VEN rising, TJ = -40C to +125C 1.279 1.1 VEN > 1.279 V 1.458 -21 V A SOFT-START ISS SS source current tSS Internal soft-start interval VSS = 0 V, TJ = 25C VSS = 0 V, TJ = -40C to +125C 50 40 50 1.6 60 A ms CURRENT LIMIT ICL (1) (2) 4 Current limit threshold DC average, TJ = -40C to +125C 3.4 A Minimum and Maximum limits are 100% production tested at 25C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely parametric norm. Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Electrical Characteristics (continued) Minimum and Maximum limits are ensured through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 12 V, VOUT = 3.3 V. PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) 711 812 914 kHz 950 kHz 0.4 V UNIT INTERNAL SWITCHING OSCILLATOR fosc Free-running oscillator frequency fsync Synchronization range VIL-sync Synchronization logic zero amplitude Relative to AGND, TJ = -40C to +125C VIH-sync Synchronization logic one amplitude Relative to AGND, TJ = -40C to +125C Sync dc Synchronization duty cycle range Dmax Maximum Duty Factor Sync input connected to ground. 650 1.5 15% V 50% 85% 83% REGULATION AND OVER-VOLTAGE COMPARATOR VSS >+ 0.8 V, IO = 3 A, TJ = 25C 0.796 VFB In-regulation feedback voltage VFB-OV Feedback overvoltage protection threshold IFB Feedback input bias current 5 nA IQ Non-switching input current VFB = 0.86 V 2.6 mA ISD Shutdown quiescent current VEN = 0 V 70 A VSS >+ 0.8 V, IO = 3 A, TJ = -40C to +125C 0.776 0.816 0.86 V V THERMAL CHARACTERISTICS TSD Thermal shutdown Rising 165 C TSD-HYST Thermal shutdown hysteresis Falling 15 C 9 mVPP PERFORMANCE PARAMETERS (3) VO Output voltage ripple Cout = 220 F with 7 m ESR + 100 F X7R + 2 x 0.047 F BW at 20 MHz VO/VIN Line regulation VIN = 12 V to 20 V, IO= 0.001 A VO/IOUT Load regulation VIN = 12 V, IO= 0.001 A to 3 A Peak efficiency VIN = 12 V, VO = 3.3 V, IO = 1 A 86% Full load efficiency VIN = 12 V VO = 3.3 V, IO = 3 A 85% (3) 0.02% 1 mV/A Refer to BOM in Table 1. Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 5 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 6.6 Typical Characteristics Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 100 3 20 Vin 12 Vin 10 Vin DISSIPATION (W) EFFICIENCY (%) 90 80 70 60 50 10 Vin 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 2 1 0 3 Figure 1. Efficiency 6-V Output at 25C Ambient 0 3 20 Vin 12 Vin 9 Vin DISSIPATION (W) EFFICIENCY (%) 90 70 60 50 9 VIn 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 2 1 0 3 Figure 3. Efficiency 5-V Output at 25C Ambient 0 3 DISSIPATION (W) EFFICIENCY (%) 70 60 6 Vin 9 Vin 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 2 1 0 3 Figure 5. Efficiency 3.3-V Output at 25C Ambient 6 3 20 Vin 12 Vin 9 Vin 6 Vin 90 80 1 2 OUTPUT CURRENT (A) Figure 4. Dissipation 5-V Output at 25C Ambient 100 50 3 Figure 2. Dissipation 6-V Output at 25C Ambient 100 80 1 2 OUTPUT CURRENT (A) 0 1 2 OUTPUT CURRENT (A) 3 Figure 6. Dissipation 3.3-V Output at 25C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 3 90 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 80 70 60 50 6 Vin 9 Vin 12 Vin 20 Vin 40 30 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 7. Efficiency 2.5-V Output at 25C Ambient 3 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 80 60 50 6 Vin 9 Vin 12 Vin 20 Vin 40 30 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 9. Efficiency 1.8-V Output at 25C Ambient 3 DISSIPATION (W) EFFICIENCY (%) 55 45 6 Vin 9 Vin 12 Vin 20 Vin 1 2 OUTPUT CURRENT (A) 2 1 0 25 0 3 20 Vin 12 Vin 9 Vin 6 Vin 75 65 1 2 OUTPUT CURRENT (A) Figure 10. Dissipation 1.8-V Output at 25C Ambient 85 35 3 Figure 8. Dissipation 2.5-V Output at 25C Ambient 90 70 1 2 OUTPUT CURRENT (A) 0 3 Figure 11. Efficiency 1.5-V Output at 25C Ambient 1 2 OUTPUT CURRENT (A) 3 Figure 12. Dissipation 1.5-V Output at 25C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 7 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 3 80 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 70 60 50 40 6 Vin 9 Vin 12 Vin 20 Vin 30 20 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 13. Efficiency 1.2-V Output at 25C Ambient 3 20 Vin 12 Vin 9 VIn 6 Vin DISSIPATION (W) EFFICIENCY (%) 70 50 40 6 Vin 9 Vin 12 Vin 20 Vin 30 20 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 15. Efficiency 1-V Output at 25C Ambient 3 DISSIPATION (W) EFFICIENCY (%) 40 30 6 Vin 9 Vin 12 Vin 20 Vin* 10 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 17. Efficiency 0.8-V Output at 25C Ambient 8 3 20 Vin* 12 Vin 9 Vin 6 Vin 60 50 1 2 OUTPUT CURRENT (A) Figure 16. Dissipation 1-V Output at 25C Ambient 70 20 3 Figure 14. Dissipation 1.2-V Output at 25C Ambient 80 60 1 2 OUTPUT CURRENT (A) 1 2 OUTPUT CURRENT (A) 3 Figure 18. Dissipation 0.8-V Output at 25C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 100 3 20 Vin 12 Vin 10 Vin DISSIPATION (W) EFFICIENCY (%) 90 80 70 60 50 10 Vin 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 2 1 0 3 Figure 19. Efficiency 6-V Output at 85C Ambient 0 3 20 Vin 12 Vin 9 Vin DISSIPATION (W) EFFICIENCY (%) 90 70 60 50 9 Vin 12 Vin 20 Vin 40 0 1 2 OUTPUT CURRENT (A) 2 1 0 3 Figure 21. Efficiency 5-V Output at 85C Ambient 0 3 DISSIPATION (W) EFFICIENCY (%) 60 50 6 Vin 9 Vin 12 Vin 20 Vin 30 0 1 2 OUTPUT CURRENT (A) 3 20 Vin 12 Vin 9 Vin 6 Vin 80 70 1 2 OUTPUT CURRENT (A) Figure 22. Dissipation 5-V Output at 85C Ambient 90 40 3 Figure 20. Dissipation 6-V Output at 85C Ambient 100 80 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 23. Efficiency 3.3-V Output at 85C Ambient 1 2 OUTPUT CURRENT (A) 3 Figure 24. Dissipation 3.3-V Output at 85C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 9 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 3 90 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 80 70 60 50 6 Vin 9 Vin 12 Vin 20 Vin 40 30 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 25. Efficiency 2.5-V Output at 85C Ambient 3 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 80 60 50 6 Vin 9 Vin 12 Vin 20 Vin 40 30 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 27. Efficiency 1.8-V Output at 85C Ambient 3 DISSIPATION (W) EFFICIENCY (%) 50 40 6 Vin 9 Vin 12 Vin 20 Vin 20 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 29. Efficiency 1.5-V Output at 85C Ambient 10 3 20 Vin 12 Vin 9 Vin 6 Vin 70 60 1 2 OUTPUT CURRENT (A) Figure 28. Dissipation 1.8-V Output at 85C Ambient 80 30 3 Figure 26. Dissipation 2.5-V Output at 85C Ambient 90 70 1 2 OUTPUT CURRENT (A) 1 2 OUTPUT CURRENT (A) 3 Figure 30. Dissipation 1.5-V Output at 85C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 3 80 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 70 60 50 40 6 Vin 9 Vin 12 Vin 20 Vin 30 20 0 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 31. Efficiency 1.2-V Output at 85C Ambient 3 20 Vin 12 Vin 9 Vin 6 Vin DISSIPATION (W) EFFICIENCY (%) 65 45 35 6 Vin 9 Vin 12 Vin 20 Vin 25 1 2 OUTPUT CURRENT (A) 2 1 0 15 0 0 3 Figure 33. Efficiency 1-V Output at 85C Ambient 3 DISSIPATION (W) EFFICIENCY (%) 40 6 Vin 9 Vin 12 Vin 20 Vin* 20 0 1 2 OUTPUT CURRENT (A) 3 20 Vin* 12 Vin 9 Vin 6 Vin 60 50 1 2 OUTPUT CURRENT (A) Figure 34. Dissipation 1-V Output at 85C Ambient 70 30 3 Figure 32. Dissipation 1.2-V Output at 85C Ambient 75 55 1 2 OUTPUT CURRENT (A) 2 1 0 0 3 Figure 35. Efficiency 0.8-V Output at 85C Ambient 1 2 OUTPUT CURRENT (A) 3 Figure 36. Dissipation 0.8-V Output at 85C Ambient Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 11 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 4 MAXIMUM OUTPUT CURRENT (A) MAXIMUM OUTPUT CURRENT (A) 4 3 2 1 JA=12C/W 0 2 1 JA = 12 C/W 0 30 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (C) VIN = 12 V, VOUT = 5 V 30 40 50 60 70 80 90 100 110 120 130 TEMPERATURE (C) VIN= 12 V, VOUT = 3.3 V Figure 37. Thermal Derating NORMALLIZED OUTPUT VOLTAGE (V/V) 3 Figure 38. Thermal Derating 1.002 1.001 1.000 0.999 9 Vin 12 Vin 20 Vin 0.998 0 1 2 OUTPUT CURRENT (A) 3 10 mV/Div VOUT = 3.3 V 500 ns/Div 12 VIN 3.3 VO at 3 A, BW = 20 MHz Figure 40. Output Ripple Figure 39. Normalized Line and Load Regulation 2A/Div 10 mV/Div 500 ns/Div 12 VIN 3.3 VOat 3 A, BW = 250 MHz 100 mV/Div 12 VIN 3.3 VO 0.5- to 3-A Step Figure 41. Output Ripple 12 500 s/Div Figure 42. Transient Response Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Typical Characteristics (continued) Unless otherwise specified, the following conditions apply: VIN = 12V; CIN = 2 x 10 F + 1-F X7R Ceramic; CO = 220-F Specialty Polymer + 10-F Ceramic; TA = 25C for waveforms. Efficiency and dissipation plots marked with * have cycle skipping at light loads resulting is slightly higher Output ripple - See Design Steps section. 9 8 CURRENT (A) 7 Output Current 6 5 4 3 2 Input Current 1 0 0 4 8 12 16 INPUT VOLTAGE (V) 20 Figure 43. Short Circuit Current vs Input Voltage Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 13 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 7 Detailed Description 7.1 Overview The architecture used is an internally compensated emulated peak current mode control, based on a monolithic synchronous SIMPLE SWITCHER core capable of supporting high load currents. The output voltage is maintained through feedback compared with an internal 0.8-V reference. For emulated peak current-mode, the valley current is sampled on the down-slope of the inductor current. This is used as the DC value of current to start the next cycle. The primary application for emulated peak current-mode is high input voltage to low output voltage operating at a narrow duty cycle. By sampling the inductor current at the end of the switching cycle and adding an external ramp, the minimum ON-time can be significantly reduced, without the need for blanking or filtering which is normally required for peak current-mode control. 7.2 Functional Block Diagram Linear Regulator 2M VIN 1 3 3 CIN EN CBST CINint 1 SYNC CSS 2 800 kHz PWM SS/TRK 3.3 uH VOUT VREF 3 RFBT CO FB 1 2 Comp RFBB AGND Regulator IC EP/ PGND Internal Passives 7.3 Feature Description 7.3.1 Synchronization Input The PWM switching frequency can be synchronized to an external frequency source. If this feature is not used, connect this input either directly to ground, or connect to ground through a resistor of 1.5 k or less. The allowed synchronization frequency range is 650 kHz to 950 kHz. The typical input threshold is 1.4-V transition level. Ideally the input clock should overdrive the threshold by a factor of 2, so direct drive from 3.3-V logic through a 1.5-k Thevenin source resistance is recommended. NOTE Applying a sustained logic 1 corresponds to zero Hz PWM frequency and will cause the module to stop switching. 7.3.2 Output Over-voltage Protection If the voltage at FB is greater than a 0.86-V internal reference, the output of the error amplifier is pulled toward ground, causing VO to fall. 14 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Feature Description (continued) 7.3.3 Current Limit The LMZ22003 is protected by both low-side (LS) and high-side (HS) current limit circuitry. The LS current limit detection is carried out during the OFF-time by monitoring the current through the LS synchronous MOSFET. Referring to the Functional Block Diagram, when the top MOSFET is turned off, the inductor current flows through the load, the PGND pin and the internal synchronous MOSFET. If this current exceeds the low-side current limit value, the current limit comparator disables the start of the next switching period. Switching cycles are prohibited until current drops below the limit. NOTE DC current limit is dependent on both duty cycle as shown in the graph in the Typical Characteristics section. The HS current limit monitors the current of top side MOSFET. Once HS current limit is detected, the HS MOSFET is shutoff immediately, until the next cycle. Exceeding HS current limit causes VO to fall. Typical behavior of exceeding LS current limit is that fSW drops to 1/2 of the operating frequency. 7.3.4 Thermal Protection The junction temperature of the LMZ22003 should not be allowed to exceed its maximum ratings. Thermal protection is implemented by an internal Thermal Shutdown circuit which activates at 165C (typical) causing the device to enter a low power standby state. In this state the main MOSFET remains off causing VO to fall, and additionally the CSS capacitor is discharged to ground. Thermal protection helps prevent catastrophic failures for accidental device overheating. When the junction temperature falls back below 150C (typical hysteresis = 15C) the SS pin is released, VO rises smoothly, and normal operation resumes. Applications requiring maximum output current especially those at high input voltage may require additional derating at elevated temperatures. 7.3.5 Prebiased Start-Up The LMZ22003 will properly start up into a prebiased output. This start-up situation is common in multiple rail logic applications where current paths may exist between different power rails during the start-up sequence. Figure 44 shows proper behavior in this mode. Trace one is Enable going high. Trace two is 1.5-V prebias rising to 3.3 V. Rise-time determined by CSS, trace three. Figure 44. Prebiased Start-Up Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 15 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 7.4 Device Functional Modes 7.4.1 Discontinuous Conduction and Continuous Conduction Modes At light load the regulator will operate in discontinuous conduction mode (DCM). With load currents above the critical conduction point, it will operate in continuous conduction mode (CCM). In CCM, current flows through the inductor through the entire switching cycle and never falls to zero during the OFF-time. When operating in DCM, inductor current is maintained to an average value equaling IOUT. Inductor current exhibits normal behavior for the emulated current mode control method used. Output voltage ripple typically increases during this mode of operation. Figure 45 is a comparison pair of waveforms of the showing both CCM (upper) and DCM operating modes. VIN = 12 V, VO = 3.3 V, IO = 3 A / 0.3 A 2 s/div Figure 45. CCM and DCM Operating Modes 16 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LMZ22003 is a step-down DC-to-DC power module. It is typically used to convert a higher DC voltage to a lower DC voltage with a maximum output current of 3 A. The following design procedure can be used to select components for the LMZ22003. Alternately, the WEBENCH software may be used to generate complete designs. When generating a design, the WEBENCH software uses iterative design procedure and accesses comprehensive databases of components. Please go to www.ti.com for more details. 8.2 Typical Application U1 7V to 20V PGND/EP VIN Enable VOUT SS FB AGND EN 3.3VO @ 3A 7 6 5 4 3 1 CIN6 OPT 2 VIN + SYNC LMZ22003TZ 150 PF RFBT RENT 3.32k 42.2k SYNC RFRA OPT 23.7O RENH OPT D1 OPT 5.1V RENB 12.7k CIN2,3 10 PF 100O CIN1,5 0.047 PF RSNOPT RFBB CSS 0.47F 1.07k CO1,6 0.047 PF CO2 100 PF OPT + CO5 220 PF 1.50 kO Figure 46. Typical Application Schematic 8.2.1 Design Requirements For this example the following application parameters exist: * VIN Range = Up to 20 V * VOUT = 0.8 V to 6 V * IOUT = 3 A Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 17 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Typical Application (continued) 8.2.2 Detailed Design Procedure 8.2.2.1 Design Steps The LMZ22003 is fully supported by WEBENCH which offers: component selection, electrical and thermal simulations. Additionally there are both evaluation and demonstration boards that may be used as a starting point for design. The following list of steps can be used to manually design the LMZ22003 application. All references to values refer to the typical applications schematic Figure 46. 1. 2. 3. 4. 5. 6. Select minimum operating VIN with enable divider resistors Program VO with resistor divider selection Select CO Select CIN Determine module power dissipation Layout PCB for required thermal performance 8.2.2.2 Enable Divider, RENT, RENB and RENHSelection Internal to the module is a 2-M pullup resistor connected from VIN to Enable. For applications not requiring precision undervoltage lockout (UVLO), the Enable input may be left open circuit and the internal resistor will always enable the module. In such case, the internal UVLO occurs typically at 4.3 V (VINrising). In applications with separate supervisory circuits Enable can be directly interfaced to a logic source. In the case of sequencing supplies, the divider is connected to a rail that becomes active earlier in the power-up cycle than the LMZ22003 output rail. Enable provides a precise 1.279 V threshold to allow direct logic drive or connection to a voltage divider from a higher enable voltage such as VIN. Additionally there is 21 A (typical) of switched offset current allowing programmable hysteresis. See Figure 47. The function of the enable divider is to allow the designer to choose an input voltage below which the circuit will be disabled. This implements the feature of programmable UVLO. The two resistors should be chosen based on the following ratio: RENT / RENB = (VIN UVLO / 1.279 V) - 1 (1) The LMZ22003 typical application shows 12.7 k for RENB and 42.2 k for RENT resulting in a rising UVLO of 5.46 V. Note that this divider presents 8.33 V to the input when the divider is raised to 20 V which would exceed the recommended 5.5-V limit for Enable. A midpoint 5.1-V Zener clamp is applied to allow the application to cover the full 6 V to 20 V range of operation. The zener clamp is not required if the target application prohibits the maximum Enable input voltage from being exceeded. Additional enable voltage hysteresis can be added with the inclusion of RENH. It is possible to select values for RENT and RENB such that RENH is a value of zero allowing it to be omitted from the design. Rising threshold can be calculated as follows: VEN(rising) = 1.279 ( 1 + (RENT|| 2 meg)/ RENB) (2) Whereas the falling threshold level can be calculated using: VEN(falling) = VEN(rising) - 21 A ( RENT|| 2 meg || RENTB + RENH) 18 Submit Documentation Feedback (3) Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Typical Application (continued) INT-VCC (5V) VIN 21 PA 2.0M RENT 42.2k RENH ENABLE RUN 100: RENB 12.7k 5.1V 1.279V Figure 47. Enable Input Detail 8.2.2.3 Output Voltage Selection Output voltage is determined by a divider of two resistors connected between VO and ground. The midpoint of the divider is connected to the FB input. The regulated output voltage determined by the external divider resistors RFBT and RFBB is: VO = 0.796 V x (1 + RFBT / RFBB) (4) Rearranging terms; the ratio of the feedback resistors for a desired output voltage is: RFBT / RFBB = (VO / 0.796 V) - 1 (5) These resistors should generally be chosen from values in the range of 1.0 k to 10.0 k. For VO = 0.8 V the FB pin can be connected to the output directly and RFBB can be set to 8.06 k to provide minimum output load. Table 1 lists the values for RFBT , and RFBB. Table 1. Typical Application Bill of Materials REF DES DESCRIPTION CASE SIZE MANUFACTURER MANUFACTURER P/N U1 SIMPLE SWITCHER PFM-7 Texas Instruments LMZ22003TZ Cin1,5 0.047 F, 50 V, X7R 1206 Yageo America CC1206KRX7R9BB473 Cin2,3 10 F, 50 V, X7R 1210 Taiyo Yuden UMK325BJ106MM-T Cin6 (OPT) CAP, AL, 150 F, 50 V Radial G Panasonic EEE-FK1H151P CO1,6 0.047 F, 50 V, X7R 1206 Yageo America CC1206KRX7R9BB473 CO2 (OPT) 100 F, 6.3 V, X7R 1210 TDK C3225X5R0J107M CO5 220 F, 6.3 V, SP-Cap (7343) Panasonic EEF-UE0J221LR ERJ-6ENF3321V RFBT 3.32 k 0805 Panasonic RFBB 1.07 k 0805 Panasonic ERJ-6ENF1071V RSN(OPT) 1.50 k 0805 Vishay Dale CRCW08051K50FKEA ERJ-6ENF4222V RENT 42.2 k 0805 Panasonic RENB 12.7 k 0805 Panasonic ERJ-6ENF1272V RFRA(OPT) 23.7 0805 Vishay Dale CRCW080523R7FKEA RENH 100 0805 Vishay Dale CRCW0805100RFKEA CSS 0.47 F, 10%, X7R, 16 V 0805 AVX 0805YC474KAT2A D1(OPT) 5.1 V, 0.5 W SOD-123 Diodes Inc. MMSZ5231BS-7-F Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 19 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 8.2.2.4 Soft-Start Capacitor Selection Programmable soft-start permits the regulator to slowly ramp to its steady-state operating point after being enabled, thereby reducing current inrush from the input supply and slowing the output voltage rise-time. Upon turnon, after all UVLO conditions have been passed, an internal 1.6-ms circuit slowly ramps the SS/TRK input to implement internal soft start. If 2 ms is an adequate turnon time then the Css capacitor can be left unpopulated. Longer soft-start periods are achieved by adding an external capacitor to this input. Soft-start duration is given by the formula: tSS = VREF x CSS / Iss = 0.796 V x CSS / 50 A (6) This equation can be rearranged as follows: CSS = tSS x 50 A / 0.796 V (7) Using a 0.22-F capacitor results in 3.5-ms typical soft-start duration; and 0.47 F results in 7.5-ms typical. 0.47 F is a recommended initial value. As the soft-start input exceeds 0.796 V, the output of the power stage will be in regulation and the 50-A current is deactivated. Note that the following conditions will reset the soft-start capacitor by discharging the SS input to ground with an internal current sink. * The Enable input being pulled low * Thermal shutdown condition * Internal VCC UVLO (Approx 4.3-V input to VIN) 8.2.2.5 Tracking Supply Divider Option The tracking function allows the module to be connected as a slave supply to a primary voltage rail (often the 3.3-V system rail) where the slave module output voltage is lower than that of the master. Proper configuration allows the slave rail to power up coincident with the master rail such that the voltage difference between the rails during ramp-up is small (that is, < 0.15 V typical). The values for the tracking resistive divider should be selected such that the effect of the internal 50-A current source is minimized. In most cases the ratio of the tracking divider resistors is the same as the ratio of the output voltage setting divider. Proper operation in tracking mode dictates the soft-start time of the slave rail be shorter than the master rail; a condition that is easy satisfy since the CSS cap is replaced by RTKB. The tracking function is only supported for the power-up interval of the master supply; once the SS/TRK rises past 0.8 V the input is no longer enabled and the 50-A internal current source is switched off. 3.3V Master 2.5Vout Int VCC 50 PA Rtkt 226 Rfbt 2.26k SS/TRK FB Rtkb 107 Rfbb 1.07k Figure 48. Tracking Option Input Detail 8.2.2.6 CO Selection None of the required CO output capacitance is contained within the module. A minimum value of 200 F is required based on the values of internal compensation in the error amplifier. Low ESR tantalum, organic semiconductor or specialty polymer capacitor types are recommended for obtaining lowest ripple. The output capacitor CO may consist of several capacitors in parallel placed in close proximity to the module. The output capacitor assembly must also meet the worst case minimum ripple current rating of 0.5 x ILR P-P, as calculated in Equation 13. Beyond that, additional capacitance will reduce output ripple so long as the ESR is low enough to permit it. Loop response verification is also valuable to confirm closed loop behavior. 20 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 For applications with dynamic load steps; the following equation provides a good first pass approximation of CO for load transient requirements. Where VO-Tran is 100 mV on a 3.3-V output design. CO IO-Tran/ [ ( VO-Tran- ESR x IO-Tran) x ( F x SW / VO)] (8) Solving: CO 2.5 A / (0.1 V - 0.007 x 2.5 A) x ( 800000 Hz / 3.3 V) 125 F (9) The stability requirement for 200-F minimum output capacitance will take precedence. One recommended output capacitor combination is a 220-F, 7-m ESR specialty polymer cap in parallel with a 100-F 6.3-V X5R ceramic. This combination provides excellent performance that may exceed the requirements of certain applications. Additionally some small ceramic capacitors can be used for high-frequency EMI suppression. 8.2.2.7 CIN Selection The LMZ22003 module contains a small amount of internal ceramic input capacitance. Additional input capacitance is required external to the module to handle the input ripple current of the application. The input capacitor can be several capacitors in parallel. This input capacitance should be located in very close proximity to the module. Input capacitor selection is generally directed to satisfy the input ripple current requirements rather than by capacitance value. Input ripple current rating is dictated by the equation: I(CIN(RMS)) 1 / 2 x IO x SQRT (D / 1 - D) where D VO / VIN * (10) As a point of reference, the worst case ripple current will occur when the module is presented with full load current and when VIN = 2 x VO. Recommended minimum input capacitance is 22-F X7R (or X5R) ceramic with a voltage rating at least 25% higher than the maximum applied input voltage for the application. TI recommends to pay attention to the voltage and temperature derating of the capacitor selected. NOTE The ripple current rating of ceramic capacitors may be missing from the capacitor data sheet and you may have to contact the capacitor manufacturer for this parameter. If the system design requires a certain minimum value of peak-to-peak input ripple voltage (VIN) be maintained then the following equation may be used. CIN IO x D x (1-D) / fSW-CCM x VIN (11) If VIN is 1% of VIN for a 12-V input to 3.3-V output application this equals 120 mV and fSW = 812 kHz. CIN 3 A x 3.3 V / 12V x (1 - 3.3 V / 12 V) / (812000 x 0.120 V) 6.14 F Additional bulk capacitance with higher ESR may be required to damp any resonant effects of the input capacitance and parasitic inductance of the incoming supply lines. The LMZ22003 typical applications schematic and evaluation board include a 150-F, 50-V aluminum capacitor for this function. There are many situations where this capacitor is not necessary. 8.2.2.8 Discontinuous Conduction and Continuous Conduction Modes Selection The approximate formula for determining the DCM/CCM boundary is as follows: IDCB VO x (VIN- VO) / (2 x 3.3 H x fSW(CCM) x VIN) (12) The inductor internal to the module is 3.3 H. This value was chosen as a good balance between low and high input voltage applications. The main parameter affected by the inductor is the amplitude of the inductor ripple current (ILR). ILR can be calculated with: ILR P-P = VO x (VIN - VO) / (3.3 H x fSW x VIN) where * * VIN is the maximum input voltage and fSW is typically 812 kHz. (13) Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 21 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com If the output current IO is determined by assuming that IO = IL, the higher and lower peak of ILR can be determined. 8.2.3 Application Curves 4 4 MAXIMUM OUTPUT CURRENT (A) 100 90 3 70 DISSIPATION (W) EFFICIENCY (%) 80 60 50 2 40 30 1 20 10 0 1 2 OUTPUT CURRENT (A) 2 1 JA=12C/W 0 0 0 3 30 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (C) 3 VIN = 12 V, VOUT = 5 V VIN = 12 V, VOUT = 5 V Figure 49. Efficiency Figure 50. Thermal Derating Curve 50 AMPLITUDE (dBuV/m) 45 40 35 30 25 20 15 Class A Limit Class B Limit Horiz Peak Horiz Quasi-peak 10 5 0 0 200 400 600 800 FREQUENCY (MHz) 1000 Figure 51. Radiated EMI (EN 55022) of Demo Board (See AN-2125) 9 Power Supply Recommendations The LMZ22003 device is designed to operate from an input voltage supply range between 6 V and 20 V. This input supply should be well regulated and able to withstand maximum input current and maintain a stable voltage. The resistance of the input supply rail should be low enough that an input current transient does not cause a high enough drop at the LMZ22003 supply voltage that can cause a false UVLO fault triggering and system reset. If the input supply is more than a few inches from the LMZ22003, additional bulk capacitance may be required in addition to the ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47F or 100-F electrolytic capacitor is a typical choice. 22 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 10 Layout 10.1 Layout Guidelines PCB layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce and resistive voltage drop in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability. Good layout can be implemented by following a few simple design rules. A good example layout is shown in Figure 54. 10.2 Layout Examples VIN VO LMZ22003 VOUT VIN High di/dt Cin1 CO1 GND Loop 2 Loop 1 Figure 52. Critical Current Loops to Minimize Top View Thermal Vias GND GND EPAD 1 2 3 4 5 6 7 VIN EN SYNC FB GND VOUT SS CIN VIN RENT SYNC CSS RENB COUT VOUT RFBT CFF RFBB GND Plane Figure 53. PCB Layout Guide Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 23 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com Layout Examples (continued) Figure 54. Top View Evaluation Board - See AN-2085 Figure 55. Bottom View Demonstration Board 10.3 Power Dissipation and Thermal Considerations When calculating module dissipation use the maximum input voltage and the average output current for the application. Many common operating conditions are provided in the characteristic curves such that less common applications can be derived through interpolation. In all designs, the junction temperature must be kept below the rated maximum of 125C. For the design case of VIN = 12 V, VO = 3.3 V, IO = 3 A, and TAMB(MAX) = 85C, the module must see a thermal resistance from case to ambient of less than: RCA< (TJ-MAX - TA-MAX) / PIC-LOSS - RJC (14) Given the typical thermal resistance from junction to case to be 1.9C/W. Use the 85C power dissipation curves in the Typical Characteristics section to estimate the PIC-LOSS for the application being designed. In this application it is 2W. RCA = (125 - 85) / 2 W - 1.9 = 18.1 24 (15) Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 Power Dissipation and Thermal Considerations (continued) To reach RCA = 18.1, the PCB is required to dissipate heat effectively. With no airflow and no external heat-sink, a good estimate of the required board area covered by 2-oz. copper on both the top and bottom metal layers is: Board_Area_cm2 = 500C x cm2/W / RCA (16) As a result, approximately 28 square cm of 2-oz. copper on top and bottom layers is required for the PCB design. The PCB copper heat sink must be connected to the exposed pad. Approximately sixty, 8 mil thermal vias spaced 39 mils (1.0 mm) apart connect the top copper to the bottom copper. For an example of a high thermal performance PCB layout for SIMPLE SWITCHER power modules, refer to AN-2085 (SNVA457), AN2125 (SNVA437), AN-2020 (SNVA419) and AN-2026 (SNVA424). 10.4 Power Module SMT Guidelines The recommendations below are for a standard module surface mount assembly * Land Pattern -- Follow the PCB land pattern with either soldermask defined or non-soldermask defined pads * Stencil Aperture - For the exposed die attach pad (DAP), adjust the stencil for approximately 80% coverage of the PCB land pattern - For all other I/O pads use a 1:1 ratio between the aperture and the land pattern recommendation * Solder Paste -- Use a standard SAC Alloy such as SAC 305, type 3 or higher * Stencil Thickness -- 0.125 to 0.15mm * Reflow - Refer to solder paste supplier recommendation and optimized per board size and density * Refer to Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214) for reflow information * Maximum number of reflows allowed is one Figure 56. Sample Reflow Profile Table 2. Sample Reflow Profile Table PROBE MAX TEMP (C) REACHED MAX TEMP TIME ABOVE 235C REACHED 235C TIME ABOVE 245C REACHED 245C TIME ABOVE 260C REACHED 260C 1 242.5 6.58 0.49 6.39 2 242.5 7.10 0.55 6.31 0.00 - 0.00 - 0.00 7.10 0.00 3 241.0 7.09 0.42 6.44 - 0.00 - 0.00 - Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 25 LMZ22003 SNVS658I - MARCH 2011 - REVISED AUGUST 2015 www.ti.com 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.1.2 Development Support For developmental support, see the following: WEBENCH Tool, http://www.ti.com/webench 11.2 Documentation Support 11.2.1 Related Documentation For related documentation, see the following: * AN-2027 Inverting Application for the LMZ14203 SIMPLE SWITCHER Power Module, (SNVA425) * Absolute Maximum Ratings for Soldering, (SNOA549) * AN-2024 LMZ1420x / LMZ1200x Evaluation Board (SNVA422) * AN-2085 LMZ23605/03, LMZ22005/03 Evaluation Board (SNVA457) * AN-2054 Evaluation Board for LM10000 - PowerWise AVS System Controller (SNVA437) * AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419) * AN-2026 Effect of PCB Design on Thermal Performance of SIMPLE SWITCHER Power Modules (SNVA424) * Design Summary LMZ1xxx and LMZ2xxx Power Modules Family (SNAA214) 11.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.4 Trademarks E2E is a trademark of Texas Instruments. WEBENCH, SIMPLE SWITCHER are registered trademarks of Texas Instruments. All other trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.6 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 26 Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 LMZ22003 www.ti.com SNVS658I - MARCH 2011 - REVISED AUGUST 2015 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright (c) 2011-2015, Texas Instruments Incorporated Product Folder Links: LMZ22003 27 PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMZ22003TZ/NOPB ACTIVE TO-PMOD NDW 7 45 RoHS & Green SN Level-3-245C-168 HR -40 to 85 LMZ22003 LMZ22003TZE/NOPB ACTIVE TO-PMOD NDW 7 250 RoHS & Green SN Level-3-245C-168 HR -40 to 85 LMZ22003 LMZ22003TZX/NOPB ACTIVE TO-PMOD NDW 7 500 RoHS & Green SN Level-3-245C-168 HR -40 to 85 LMZ22003 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 27-May-2018 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMZ22003TZE/NOPB TOPMOD NDW 7 250 330.0 24.4 10.6 14.22 5.0 16.0 24.0 Q2 LMZ22003TZX/NOPB TOPMOD NDW 7 500 330.0 24.4 10.6 14.22 5.0 16.0 24.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 27-May-2018 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMZ22003TZE/NOPB TO-PMOD NDW 7 250 367.0 367.0 45.0 LMZ22003TZX/NOPB TO-PMOD NDW 7 500 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA NDW0007A BOTTOM SIDE OF PACKAGE TOP SIDE OF PACKAGE TZA07A (Rev D) www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated