GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Product Specification Applications * Personal Navigation Devices (PNDs) * Feature phones / Smart phones * Portable Media Players (PMPs) * Smart Watches * Personal Digital Assistants (PDAs) * Asset Tracking / Personal Safety Features * Easy to use, low cost single package GPS RF antenna module * Mediatek MT3337-E chip * Ultra small SMT package; 13.8 x 9.5 x 1.8mm * Low current consumption <200uA required for Periodic mode. * Novel external matching ensure easy tuning for each platform * AIC, Active Interference Cancellation for anti Jamming. EASY - Internally generated orbit prediction for fast fix times. * Functional Block Diagram Description Antenova M2M's GPS RADIONOVA(R) M10478-A2-1 antenna module is an ultra-compact single package solution that combines full GPS receiver and antenna on the same module. The M10478-A2-1 is a highly integrated GPS RF antenna module suitable for L1-band GPS systems. The device is based on the Mediatek MT3337-E GPS architecture combined with Antenova's antenna technology. Using patented external matching means this module is suitable from small watch applications to large tracker devices. All front-end and receiver components are contained in a single package laminate base module, providing a complete GPS receiver for optimum performance. The M10478-A2-1 operates on a versatile 2.8V-4.2V supply with low power consumption and several low power modes for further power savings. An accurate 0.5ppm TXCO ensures short TTFF. Indoor and outdoor multi-path detection and compensation. Providing a true drop in solution with the antenna and R F in a single SMT package, GPS RADIONOVA(R) M10478-A2-1 offers ease of integration and shorter design cycles for faster time to market. Package Style SMD Castellated pads enable SMT placement and re flow as well as hand soldering. 13.8 x 9.5 x 1.8 (mm) RF Antenna Module Top View Antennas for Wireless M2M Applications Bottom View 1 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Absolute Maximum Ratings Symbol Parameter Min Max Unit V Main Supply Voltage -0.3 4.3 V Supply voltage I/O ring -0.3 3.6 V VBATT VBCKP Supply -0.3 4.3 V RF Maximum RF Input Power N/A +10 dBm Storage Temperature -40 +85 C Operating Temperature -40 +85 C CC V IO IN T STG T A * Exposure to absolute ratings may adversely affect reliability and may cause permanent damage. Recommended Operating Conditions Symbol Parameter Min Typ Max Unit V Main Supply Voltage 2.8 3.3 4.3 V VBCKP Supply 2.8 3.3 4.3 V Operating Temperature -40 - +85 C CC V BATT T OP . DC Electrical Characteristics Conditions: V = 3.3V, T CC OP = 25 C Symbol Parameter Typ Unit I Peak Acquisition Current 31 mA Average Tracking Supply Current 24 mA Standby (Sleep) Power Supply Mode <200 A Backup Mode <200 A CC(PK) I CC(AVG) I CC(STBY) I CC(BCKUP) RF Specifications Conditions: V = 3.3V, T = 25C, Freq = 1575.420MHz CC OP Symbol Parameter Typ Unit N FLNA LNA Noise Figure 2 dB A NTRL Antenna Return Loss -15 dB A NTBW Antenna Bandwidth at -10dB return loss 30 MHz A NTEFF Antenna Total Efficiency >40% % A NTEFF_RHCP Antenna RHCP Efficiency >30% % Antennas for Wireless M2M Applications 2 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Band Rejection Frequency Standard Typ* Unit 698-798 LTE700 43 dB 824-849 Cellular CDMA 43 dB 869-894 GSM850 43 dB 880-915 GSM900 43 dB 1710-1785 GSM1800/DCS 44 dB 1850-1910 GSM1900/PCS 46 dB 1920-1980 WCDMA 46 dB 2400-2492 WLAN, BT and WiMAX 50 dB 2500-2690 LTE2600 52 dB *Does not include antenna rejection. Mechanical Specifications Parameter Module exterior dimensions (L x W x H) Module support and connection Module mass Typ 13.8 (0.1) x 9.5 (0.1) x 1.8 (+0.2 / - 0.0) Unit mm Surface mounted (SMD) - <1 g Antennas for Wireless M2M Applications 3 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 System Specifications Communication Specification Data Output Protocol NMEA 0183 Host Interfaces UART Default data rate on UART 4800/9600/38400/115200 bps GPS Engine Chip MTK MT3337-E Chip Channels 210 PRN / 66 Acquisition / 22 Tracking TCXO 0.5ppm Accuracy Horizontal Position Accuracy <2.5m CEP Maximum Position Update Rate 5 Hz Sensitivity Acquisition (Cold) -148dBm Acquisition (Hot) -163dBm Tracking -165dBm TTFF Hot Start <1s Warm Start <25s (typical) Cold Start <35s (typical) General Maximum Altitude <18.000 km Maximum Speed <514 m/s Active Interference Cancellers 12 multi tone active cancellers ISSCC2011 award Additional Features 1PPS Sync EPO / EASY Orbit prediction 50% CEP, Open-Sky, 24hr Static, -130dBm, good view of the sky Antennas for Wireless M2M Applications 4 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Pin out Description Table shows the designation and function of each pin on the M10478-A2-1 module. Please note that several pins have multiple functions. Pin Designator 1 2 GND Ground connection GND Ground connection 3 GND Ground connection 4 ANT_OUT 5 GND 6 ANT_IN 7 GND Ground connection 8 VCC Main DC supply, +2.8 to +4.2V 9 GND Ground connection 10 System reset, active low 11 HRST TM 12 VBCKUP 13 EINT2/GIO14 Hardware Baud rate select 14 EINT3/GIO15 Hardware Baud rate select 15 GND 16 17 18 19 20 GND GND FIXED INDICATOR GND TX Description RF from internal antenna to external matching circuit Ground connection RF from external matching circuit back into module 1PPS Tim Mark Out Backup supply +2.0V to 4.2V Ground connection Ground connection Ground connection Indicates once a GPS fix has been obtained. Ground connection UART Transmit data line 21 RX 22 GND Ground connection 23 GND GND GND Ground connection Ground connection 24 25 26 HW_STANDBY UART Receive data line Ground connection Used to enable standby mode. If not used leave floating. 27 GND Ground connection 28 GND Ground connection Antennas for Wireless M2M Applications 5 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Pin 1 Pin 28 Pin 11 Pin 18 Antennas for Wireless M2M Applications 6 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Application Schematic Example for M10478: UART - 9600 Baud The circuit below shows a basic design for use with the UART interface and configuring the default baud rate to 9600. Baud Rate = 9600 (Hardware configured) Bill of Material Designator Value C1, L1, L2 TBD C3, C4, C5, C6 22pF capacitor Decoupling capacitor. Place close to corresponding pin 4 C2 2.2uF capacitor Decoupling capacitor. Place close to corresponding pin 1 Filter component to suppress any potential host PCB noise 2 L3, L4 47nH Inductor Description/Comments Depending on device antenna matching circuit Antennas for Wireless M2M Applications Quantity TBD 7 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Host Baud Rate/Protocol Selection The modules default baud rate is user configurable at start-up with a hardware configuration. This is limited to the values in the following table. The baud rate and output protocol can be changed dynamically after start up using the relevant commands. Please contact Antenova for more information about protocol messages. Hardware Baud Rate Selection Table Baud Rate Pin13 (GIO) Pin 14 (GIO) 9600 NC NC 115200 NC PD 4800 PD NC 38400 PD PD NC = Not connected. Leave floating PD = Pull down resistor to GND (10K ) Host Interface Overview UART Interface The UART converts bytes of data to and from asynchronous start -stop bit streams as binary electrical impulses. The port contains a 16-byte FIFO, and 256 bytes of URAM. The bit rates are selectable from 4800, 9600, 38400 and 115200 bps. The IO level from the UART port are CMOS compatible, however for RS232 compatibility the use of external level shifters will be required. The hardware configuration of the port baud can be changed dynamically by the use of commands. These will be active and saved as long as the VBACKP supply is applied. The default protocol is determined by hardware configuration. Antennas for Wireless M2M Applications 8 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Power Supply The M10478-A2-1 uses two DC supply inputs. VBCKUP to power the RAM and RTC sections of the receiver, and VCC to power the digital and processing sections. VBCKUP is to be applied all the time to keep these sections alive. VCC can be removed to initiate a backup power save mode (See page 9). VBCKUP can be removed if a battery is also used at VBCKUP to maintain this supply. The supply is internally regulated for 2.8V meaning the external supply is versatile for a range of voltage levels. TM (1PPS) TM is a one pulse per second output from the receiver providing uses for timing purposes. The pulse is not only limited to being active every second, but also allows the setup to a required duration, frequency and active high/low by programming user defined settings. PPS Sync NMEA The latency range of the beginning of UART Tx is between 170ms and 180ms and behind the rising edge of the PPS. 1Hz NMEA output and baud rate at between 14400 - 115200 Enable this function using PMTK255 (Default off) HRST (Hardware Reset Pin) The External reset pin is default high by an internal 75Kohm and should be left floating if not used. To initiate a reset the pin needs to be pulled low. The module also initiates a reset if the VCC drops below the minimum 2.8V supply. Antennas for Wireless M2M Applications 9 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Power Management The M10478-A2-1 has three power saving modes. * * * Standby mode Back up mode Periodic mode Standby Mode Standby mode is a power saving mode that shuts down the RF section of the module and puts the processor into a standby mode. The RTC is kept alive and the RAM power is maintained to keep the module configuration. The standby state can be initiated either with a hardware signal to Pin26 or by using a command. Hardware controlled Standby: Enable standby mode by a low state to pin 26 (HW_STANDBY). To wake the module back to full power a high state needs to be applied to pin 26. If Pin 26 is not to be used then it must be kept floating (not connected). Standby mode command: Software on the host needs to send the "PMTK161 command through the UART interface. Command M10478-A2-1 standby then wakeup $PMTK161,0*28 M10478-A2-1 enters standby mode Any byte M10478-A2-1 wakes up from standby mode Current consumption (Typ) <200uA Back up mode To enter backup mode the VCC simply needs to be removed. Once initiated the RTC and all configuration is saved along with any ephemeris data to allow quick TTFF once the VCC is re-applied. VBACKUP needs to be applied at all times for backup mode to run correctly. Periodic mode Periodic mode is a module controlled mode that reduces current consumption by only waking the module for short periods to maintain fix data. The periodic state is user configured. Contact Antenova for more information and a user command manual. PMTK225 setting M10478-A2-1 time off/awake Current usage (Typ) PMTK225, 2,3000,18000,72000 Module sleeps for 12secs, then wakes for 3secs periodically. 72000 is for a cold boot condition. <200uA Antennas for Wireless M2M Applications 10 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 EPO (Extended Prediction Orbit) data service The EPO allows the use of up to a 30-day orbit predictions that can be used to aid the module for an instant fix solution * * * A proxy server on the customer's side to update EPO files from the MTK server daily. Application software to access the proxy server through the internet (optional if host device can access internet Software on host device to send EPO data to M10478-A2-1 module to allow instant fix by using EE data. Please contact Antenova for more information. Requires permission from MTK to use service. EASY (Self-Generated Orbit prediction) TM The module supports EASY (Embedded Assisted System) is a Self-Generated Orbit Prediction feature. It provides up to 3 days GPS orbit prediction ability without the need for any host CPU porting or internet connection requirements. EASY works as embedded software which accelerates TTFF by predicting satellite navigation messages from received ephemeris. EASY is a fully automated receiver task that is efficiently scheduled and computed in free time of every second after a GNSS navigation solution. EASY is default off and can be enabled by a PMTK command. AIC (Active Interference Cancellation) The AIC feature provides effective narrow-band interference and jamming elimination. The GPS signal can be recovered from the jammed signal and allows users to obtain better navigation quality. This can be beneficial since many of today's devices have more and more functionality with regards to transmitters with many on-board antennas Antennas for Wireless M2M Applications 11 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 External Matching The M10478-A2-1 module uses a matching circuit on the host PCB in order to fine-tune the on-board antenna to each specific application. This "external matching" allows compensating for the detuning of the antenna caused by various different components that can be close to the M10478-A2-1 module in the actual application (plastic case, battery, speakers etc). The external matching must be placed on the host PCB between ANT_OUT (PIN3) and ANT_IN (PIN1). Although 2 components are typically more than enough to match the antenna to the 50 impedance required, a -network topology with 3 components is recommended for safe proving. Schematic Both low-pass and hi-pass topologies for the matching network can be used with similar results. As the same footprint can be used for both topologies, the exact type and value of the components used can be determined during the optimization phase. * The initial values can be simply chosen as the null-circuit (no impedance matching): * * Hi-pass: * C1 = 18pF * L1, L2 = Not Fitted Low-pass: * L1 = Jumper (0 resistor) * C1, C2 = Not Fitted Antennas for Wireless M2M Applications 12 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Type of Matching Components * Capacitors: * * Use 0402, COG components Inductors: * High-Q, wire wound inductors in 0402 size are recommended for maximum performance, e.g. Murata LQW15 series * Good quality multi-layer type inductors (e.g. Murata LQG15 series) can also be used as a lower cost alternative Matching Procedure The types and values of the matching components must be chosen so that the impedance seen by port ANT_IN (PIN4) is as close as possible as 50. Although it is a relatively simple operation, it requires some RF skills and a VNA (Vector Network Analyzer). Please contact an Antenova M2M FAE to get support on defining the optimal matching for your specific device. External Antenna Support A low cost external circuit can be used to provide external antenna support. Please contact Antenova for more information, and example circuit. PCB Matching Circuit Layout The layout of the external matching circuit should be done using the following guidelines: * Minimize the length of the tracks connecting the ANT_OUT and ANT_IN pads to the matching * Minimize the length of the tracks between the components * Use a solid ground plane under the matching circuit area * Absolutely avoid routing any track under the matching circuit area * Connect the top ground layer with the ground layer underneath using several vias Layout drawings (Gerber or other format) are available from Antenova. Please contact your local FAE. Example of external matching circuit layout Antennas for Wireless M2M Applications 13 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Internal Antenna Clearance The M10478-A2-1 module internal antenna requires a small clearance on the host PCB to operate. The clearance means that no Ground or tracks of any kind are allowed to be within this area. This must also be clear through the entire PCB stack up. The minimum area needed clear is 6mm X 4.87mm. Top view of M10478 Footprint Keep out area Antennas for Wireless M2M Applications 14 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Typical RF Antenna Module Placement Note: Module placement locations and orientations are critical for achieving optimal system performance. It is strongly recommended to contact Antenova M2M for design recommendations. Below is the placement shown on the Antenova evaluation PCB. Sky Front View Back View Side View Antennas for Wireless M2M Applications 15 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Typical Antenna Matching Results Typical antenna matching as seen by ANT_IN (Pin 3) is shown in the following plot. The matching bandwidth at -10dB is typically 30MHz. Measured on M10478-U1 test board. 5 [dB] 0 -5 -10 -15 -20 2 -25 1 -30 -35 1250 1350 1450 1550 1650 1750 [MHz] 1850 MARKERS: MHz dB M10478-A2-1_0p7Fshu_4n7Hser.S1P - S11 1: 1573.42 -29.49 2: 1577.42 -26.21 Typical antenna return loss after matching 50j - -50j Antennas for Wireless M2M Applications 16 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Front-end Rejection The figure below shows the rejection for the input SAW filter before the RF input, including the effect of pads, tracks and decoupling. The plot can be useful to calculate the isolation required from adjacent transmitters in order to avoid the saturation of the LNA. 10 [dB] A tyune 1 2 0 -10 -20 -30 -40 -50 -60 -70 -80 700 1230 1760 2290 2820 3350 3880 4410 4940 5470 [MHz] 6000 Input SAW Rejection - Wideband 10 [dB] A tyune 12 -10 -20 -30 -40 -50 -60 -70 -80 1200 [MHz] 1300 1400 1500 1600 1700 1800 1900 2000 Input SAW Rejection - Narrowband Antennas for Wireless M2M Applications 17 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Module Placement Guidelines Due to the internal antenna, care must be taken when defining the placement of the module on the host PCB. Here are some guidelines that should be used when deciding the position of the module. * The module top edge must be placed almost level with the edge of the host PCB * The edge of the host PCB that the module is to be placed at must be a minimum of 40mm in length. Module top edge placed level with the edge of the host PCB * The central placement of the module is advised. However, an offset placement is also possible. * For an offset closer to the PCB edge to the right side of the module, a minimum of 10mm distance is required to the edge of the host PCB. * For an offset closer to the PCB edge on the left side of the module, a minimum of 15mm distance is required to the edge of the host PCB. This additional distance is due to the matching circuit placement. Antennas for Wireless M2M Applications 18 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 * For an offset closer to the PCB edge to the left side of the module, a minimum of 15mm distance is required to the edge of the host PCB. This additional distance is due to the matching circuit placement. * The antenna uses the host PCB ground to effectively radiate. As such, a GND plane must be placed on the host PCB on at least one layer. * In the example below, the only area void of GND is the antenna keep-out area. Antennas for Wireless M2M Applications 19 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 * An ideal stack-up for a host PCB would be to use the top and bottom layers as GND planes, while using the internal layers for any signal and power planes. This not only helps the GPS antenna to perform effectively, but also helps to reduce any potential noise issues that can be associated with mixed signal PCB's. * An exaggerated example below shows a 4 layer host PCB, GND flooding all available space not used by signals or components. Please contact Antenova M2M for advice on placement. Antennas for Wireless M2M Applications 20 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Module Footprint Below is the recommended footprint for the module. This footprint allows hand soldering. * * All pads are 0.7mm x 2mm Pitch is 1.1mm Mechanical Drawing 13.8 ( 0.1) 9.5 ( 0.1) All Dimensions in mm 1.8 (0.1) Antennas for Wireless M2M Applications 21 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Reflow Soldering Placement Typical placement systems used for any BGA/LGA package are acceptable. Recommended nozzle diameter for placement: 5mm Soldering Paste Use of "No Clean" soldering paste is strongly recommended, as it does not require cleaning after the soldering process has taken place. An example of suitable soldering paste is Alpha OM350. Soldering The recommended soldering profile for M10478-A2-1 is shown below. However, it is the responsibility of the Contract Manufacturer to determine the exact reflow profile used, taking into consideration the parameters of the host PCB, solder paste used, etc. Profile Feature Pb-Free Solder Temperature (Ts) Min 130C Temperature (Ts) Max 220C Time (ts ) <150s Liquidus Temperature - (Tl ) 220C Time (tl ) 45-90s Pre-Heat Reflow Peak Package Body Temperature (Tp) 245C Time within 5C of peak temp (tp) 30s Average Ramp up rate - Ts(max) to (Tp) 3C/s Ramp Down Rate 6C/s max Example Reflow profile The Pb Free Process-Package Peak Reflow Temperature is 260C. Exceeding the maximum soldering temperature could permanently damage the module. Antennas for Wireless M2M Applications 22 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478 Multiple Soldering The M10478-A2-1 module can be submitted up to 2 reflow soldering processes. Upside-down soldering is acceptable but it is recommended that the Contract Manufacturer qualify the process before mass production. The second reflow must take place within the recommended floor life limit (MSL3). Please contact Antenova for further information. Hand Soldering Hand-soldering and rework of the M10478-A2-1 module is acceptable, however care must be taken to avoid short circuits due to the small size of the module pads. Antennas for Wireless M2M Applications 23 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Quality and Environmental Specifications Test Standard Parameters PCB Inspection IPC-6012B, Class 2. Qualification and Performance Specification for Rigid Printed Boards - Jan 2007 Assembly Inspectio n Temperatur e Range IPC-A-610-D, Class 2 "Acceptability of electronic assemblies" ETSI EN 300 019-2-7 specification T 7.3 -30 C, +25 C, +85 C, operating Damp Heat ETSI EN 300 019-2-7 specification T 7.3 +70 C, 80% RH, 96 hrs, nonoperating Thermal Shock ETSI EN 300 019-2-7 specification T 7.3 E -40 C ... +85 C, 200 cycles Vibration ISO16750-3 Random vibration, 10~1000Hz, 27.8m/s2, 8hrs/axis, X, Y, Z 8hrs for each 3 axis non-operating Shock ISO16750-3 Half-sinusoidal 50g, 6ms, 10time/face, X, Y and Z non-operating Free Fall ISO16750-3 1m height, 2 drops on opposite side ESD Sensitivity JEDEC, JESD22-A114 ESD Sensitivity Testing Human Body Model (HBM). Class 2 +2000V - Human hand assembly JEDEC, JESD22-A115 ESD Sensitivity Testing Machine Model (MM), Class B +200V - Machine automatic final assembly Shear IEC 60068-2-21, Test Ue3: Shear Force of 5N applied to the side of the PCB Moisture/Reflo w Sensitivity IPC/JEDEC J-STD-020D.1 MSL3 Storage (Dry Pack) IPC/JEDEC J-STD-033C MSL3 Solderability EN/IEC 60068-2-58 Test Td More than 90% of the electrode should be covered by solder. Solder temperature 245 C 5 C Moisture Sensitivity Antenova ships all devices dry packed in tape on reel with desiccant and moisture level indicator sealed in an airtight package. If on receiving the goods the moisture indicator is pink in colour or a puncture of the airtight seal packaging is observed, then follow J-STD-033 "Handling and Use of Moisture/Reflow Sensitive Surface Mount Devices". Storage (Out of Bag) The M10478-A2-1 modules meet MSL Level 3 of the JEDEC specification J-STD-020D - 168 hours Floor Life (out of bag) 30 C/60% RH. If the stated floor life expires prior to reflow process then follow J-STD-033 "Handling and Use of Moisture/Reflow Sensitive Surface Mount Devices". Antennas for Wireless M2M Applications 24 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Hazardous material regulation conformance The RF antenna module meets RoHS requirements. Packaging Tape Characteristics W F E P0 P1 P2 32.000.3 14.200.1 1.750.2 4.000.1 160.1 2.000.1 D0 B0 T K0 A0 D1 1.550.1 14.800.1 0.300.1 2.000.1 10.500.05 0.850.1 Dimensions in mm Quantity Leading Space Trailing Space 1000 pcs / reel 50 blank module holders 50 blank module holders Antennas for Wireless M2M Applications 25 Product Specification 12MD-0050-4-PS -PS GPS RADIONOVA(R) RF Antenna Module Part No. M10478-A2-1 Reel Dimensions Width Reel Diameter Hub Diameter Shaft Diameter (W) (D) (H) (C) 32.0mm 330.02mm 100.0mm 13.0+0.2/-0.0mm Antennas for Wireless M2M Applications 26 Product Specification 12MD-0050-4-PS -PS Corporate Headquarters USA Headquarters Asia Headquarters Antenova Ltd. nd 2 Floor, Titan Court, 3 Bishop Square, Hatfield, AL10 9NA UK Antenova USA 100 Brush Creek Road, Suite 103, Santa Rosa, CA 95404 USA Antenova Asia Ltd. 4F, No. 324, Sec. 1, Nei-Hu Road Nei-Hu District Taipei 11493 Taiwan, ROC Tel: +44 (0) 1223 810600 Email: sales@antenova-m2m.com Tel: +1 (707) 890 5202 Email: sales@antenova-m2m.com Tel: +886 (0) 2 8797 8630 Fax: +886 (0) 2 8797 6890 Email: sales@antenova-m2m.com Copyright(R) Antenova Ltd. All Rights Reserved. Antenova(R), Antenova M2M, RADIONOVA(R) and the Antenova and Antenova M2M logos are trademarks and/or registered trademarks of Antenova Ltd. Any other names and/or trademarks belong to their respective companies. The materials provided herein are believed to be reliable and correct at the time of print. Antenova does not warrant the accuracy or completeness of the information, text, graphics or other items contained within these information. Antenova further assumes no responsibility for the use of this information, and all such information shall be entirely at the user's risk. as Wi less M2 ppli i s Product Specification 12MD-0050-4-PS Release Date 21 October 2015