Solid Electrolytic Capacitors with Polymerized Organic Semiconductor 2007-10 w w w . e d c . s a n y o . c o m Solid Electrolytic Capacitors with Polymerized Organic Semiconductor PRECAUTIONS This catalog was produced in October 2007.Product names and specifications are subject to change and products themselves are subject to discontinuation without prior notice. Be sure to check the specifications before using your product. Products described herein are not intended for applications requiring extremely high reliability (for example, those in which extensive human injury or property damage may occur such as with life-support systems or aircraft control systems). For such applications,consult our sales department. This document defines performance,characteristics and functions of each product under predetermined conditions.It does not guarantee performance,characteristics and functions when used in customer systems.Be sure to check your system before using the product for possible problems or occurrences that cannot be detected during the evaluation testing of each product. Electronic Device Company has full confidence in the quality and reliability of its products.However,misuse can result in personal injury,fire or other property damage. For questions regarding usage,please contact our sales department. Should you wish to export any product that is listed as regulated goods (including services) under the Foreign Exchange and Foreign Trade Law, an export license is required before exporting . This document may not be reprinted or reproduced in part or whole without the permission of Electronic Device Company. Electronic Device Company shall not be held responsible for any problems affecting a third party's industrial property arising from use of these products unless such problems are caused by structural or manufacturing flaws. Series integration Please make note that all models from TPA, APA, APB series as well as the 16V TPB* TPC series, some models of the TPD series are being integrated into the following series. Discontinued series Integrated series TPA TPB APA APC APB APD TPB(16TPB47M,16TPB47ML) TQC(16TQC47M) TPC(16TPC33M) TQC(16TQC33M) 10TPD150M 10TPF150ML 6TPD330M 6TPF330ML 6TPD220M 6TPF220ML 4TPD470M 4TPF470ML 4TPD330M 4TPF330ML 2R5TPD680M 2R5TPF680ML 2R5TPD680M8 2R5TPF680M8L 2R5TPD470M 2R5TPF470ML 2R5TPD470M8 2R5TPF470M8L INDEX SANYO POSCAP CAPACITORS Product guide Product Line-up Table 2 Out Line 3 Series System Diagram 4 Products List 6 Guidelines and Precautions for Use 8 Environmental Consideration 11 Marking 12 Explanation of Part Numbers 13 Structure 14 Taping Specifications 15 Recommended Land Pattern Dimension 16 Recommended Soldering Condition 17 Characteristics 18 Specifications of POSCAP in Series TPB Series 20 TPB Series B2 size 22 TPC Series 24 TPC Series B1 size 26 TPD Series 27 TPE Series D2E,D3L,D4 size 28 TPE Series C3,C2,B2 size 30 TPF Series 32 TPG Series 33 TPL/TPLF Series 34 TPU Series 36 TA Series 37 TH Series 38 TR Series 40 TQC Series 42 APC/APD Series 43 Adoption Example POSCAP is uniquely structured solid electrolytic capacitor. note the operating precautions in order to take full advantage of the POSCAP's performance and ensure the most stable quality possible. Please 44 Product Line-up Table Page Capacitance range (F) Rated Voltage range (V.DC) Category temperature range (C) High Voltage High Reliability Low ESL High Capacitance Low ESR Small size Characteristics Low Profile Product Line-up Table 2 Series Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPB Standard Products --55 to +105 2.5 to 10 033 to 1000 20 TPC Low Profile Products --55 to +105 2.5 to 12.5 10 to 330 TPD Low ESR . High Capacitance Products --55 to +105 2.5 to 6.3 470 to 1000 27 TPE Low ESR Products --55 to +105 2 to 10 047 to 1500 28 T P F Low ESR . High Capacitance Products --55 to +105 2 to 10 150 to 6800 32 TPG Small Size . High Capacitance Products --55 to +105 2.5 to 12.5 33 to 2200 33 T P L Low ESR . Low ESL Products Face Down Terminal Type --55 to +105 2.5 220 to 4700 34 TPLF Low ESR . Low ESL Products Face Down Terminal Type --55 to +105 2 220 to 4700 34 TPU Small Size . Low Profile Products Face Down Terminal Type --55 to +85 2.5 to 10 10 to 1000 36 T A High Reliability Products (For The Car Electronics) --55 to +105 2.5 to 10 T H 125C Guaranteed Products --55 to +125 2.5 to 10 T R High Moisture Resistance Products --55 to +105 2.5 to 10 TQC High Voltage Products --55 to +105 16 to 25 APC Aluminum Anode Products --55 to +105 4 to 6.3 10 to 330 43 APD Aluminum Anode . Low Profile Products --55 to +105 4 to 6.3 10 to 150 43 47 to 680 24 37 068 to 1000 38 33 to 680 40 5.6 to 680. 42 Out Line Solid Electrolytic Capacitors with Polymerized Organic Semiconductor "POSCAP" is a solid electrolytic chip capacitor. The Anode is sintered Tantalum and the Cathode is a highly conductive polymer formed on SANYO "POSCAP" has a Lowest E.S.R. (Equivalent Series Resistance) level and excellent performance for high Out Line Original method. frequency though low profile and high capacitance. In addition, it has high reliability and high heat resistance. Therefore, "POSCAP" is an ideal chip capacitor especially for digital, high frequency devices. Features Lead free Terminal plating is Palladium and Gold. It's completely lead free. Low profile chip capacitor Low impedance and low ESR at high frequency High ripple current capability Long Life 105Cx2,000Hrs* Excellent noise-absorbent characteristics Excellent temperature characteristics up to -55C The rush current is guaranteed for 20A Superior to Ta-Cap in safety *A part of the model is excluded. Applications DC/DC Converter Personal Computers VCR, Camcorder, Digital Still Camera Portable Communications Devices and Base Station PDA (Portable terminals, etc.) Navigation System HD Drive, MO Drive, DVD Drive 3 Series System Diagram Solid Electrolytic Capacitors with Polymerized Organic Semiconductor P.20-23 TPB Standard Products D4 size 2.5 to 10V 220 to 1000F Series System Diagram D3 size 2.5 to 10V 100 to 330F D3L size 2.5 to 10V 100 to 680F C size P.24-26 P.28-31 TPC TPE Low Profile Products Low ESR Products D2 size D4 size 2.5 to 10V 68 to 330F 2.5 to 10V 330 to 1500F C1 size D3L size 2.5 to 8V 33 to 100F 2.5 to 10V 220 to 680F B1 size D2E size 2.5 to 12.5V 10 to 56F 2.5 to 10V 68 to 470F 2.5 to 10V 47 to 220F C3 size B2 size P.33 P.36 2.5 to 10V 33 to 220F TPU Small Size*Low Profile Products Face Down Terminal Type TPG Small Size*High Capacitance Products B09 size B15G size 4 to 8V 33 to 68F 4 to 6.3V 150 to 220F A09 size B1G size 10V 33F 2.5 to 12.5V 33 to 220F 2.5 to 10V 150 to 330F C2 size 2.5 to 8V 100 to 330F B2 size 2 to 10V 47 to 330F P.27 P.43 APC Aluminum Anode Products 2.5 to 6.3V 22 to 47F TPD Low ESR*High Capacitance Products D2 size S08 size D4D size 4 to 6.3V 10 to 33F 2.5 to 6.3V 10 to 22F 2.5 to 6.3 V 470 to 1000F P.43 APD Aluminum Anode * Low Profile Products D1 size 4 to 6.3V 10 to 15F 4 S11 size Series System Diagram Solid Electrolytic Capacitors with Polymerized Organic Semiconductor P.38-39 TH 125C Guaranteed Products P.37 TA P.40 TR P.42 TQC High Moisture Resistance Products High Voltage Products D4D size D3L size D3L size D3L size 2.5 to 6.3V 330 to 680F 2.5 to 10V 150 to 680F 2.5 to 10V 150 to 680F 16 to 25V 33 to 68F D4 size D2E size D2E size D2 size 2.5 to 10V 220 to 1000F 2.5 to 10V 68 to 470F 2.5 to 10V 68 to 470F 16 to 25V 15 to 47F D3L size B2 size B2 size C size 2.5 to 10V 100 to 470F 4 to 10V 47 to 100F 2.5 to 10V 33 to 220F 16 to 25V 10 to 22F D2 size B15 size B2 size 2.5 to 6.3V 68 to 220F 6.3V 150F 16 to 25V 5.6 to 10F Series System Diagram High Reliability Products (For The Car Electronics) D2E size 2.5 to 8V 150 to 330F P.32 TPF Low ESR* High Capacitance Products NEW P.34-35 TPL Low ESR*Low ESL Products Face Down Terminal Type D3L size D2T size 2.5 to 10V 100 to 680F 2.5V 220 to 470F D2E size 2V 220 to 470F P.34-35 TPLF Low ESR*Low ESL Products Face Down Terminal Type D2T size 2V 220 to 470F The size of each photo is close to full scale. 5 Products List Solid Electrolytic Capacitors with Polymerized Organic Semiconductor I:18, M:25) *Under development *1(F:15, *2(C:12, F:15, I:18, M:25) *3(9, C:12, F:15, I:18, M:25) *4(5, 6, 8, 10) WV Series Series F 2.2 4.7 5.6 6.8 8.2 10 15 *Symbols in table:Case Size *( ):ESR specitication(mmax.) 22 33 47 56 TPE 2V TPE TPF TPLF TPB TPB B1(70) TPC TPD Products List TPE 2.5V TPE TPE TPE TPF TPG TPL S08(250) TPU 3.15V S11(150) TPU TPB TPB TPB C1(70) TPC B1(70) TPC TPD TPE 4V TPE TPE TPE TPF TPG S08(250) TPU S11(150) TPU D2(40) APC D1(70) APD B2(70) TPB TPB TPB B1(70) TPC B1(70) TPC TPD TPE 6.3V TPE TPE TPE TPF TPG S08(250) S11(150) APC D2(70) D2(40) APD D1(70) TPU B09(70) A09(150) TPU B2(70) TPB B1(70) TPC 8V TPE B1G(70) TPG TPU B09(70) TPB B2(70) C(55) B2(70) TPB B1(70) TPC 10V B2(70) C1(70) B2(35) TPE TPF 12.5V 16V 6 TPG B1G(70) TPU A09(150) B1(80) TPC B1(80) B1G(70) TPG C(80) D2(70) C(80) D2(80) D2(45) D2(90,45) D2(90,45) D3L(60) B2(100) TQC TQC 25V TQC D2(70) D3L(45) TQC 20V B1G(70) B2(100) B2(100) C(95) D3L(55) Products List Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Case size (unit:mm) S08 S11 A09 B09 B1 B1G B15G B2 C1 C2 C3 C D1 D2E D2T D2 D3L D3 D4D D4 L 2.0 2.0 3.2 3.5 3.5 3.5 3.5 3.5 6.0 6.0 6.0 6.0 7.3 7.3 7.3 7.3 7.3 7.3 7.3 7.3 W 1.25 1.25 1.6 2.8 2.8 2.8 2.8 2.8 3.2 3.2 3.2 3.2 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 H 0.8 1.1 0.9 0.9 1.1 1.1 1.4 1.9 1.4 1.8 2.5 2.8 1.4 1.8 1.8 1.9 2.8 3.1 3.6 3.8 WV Series F 68 82 100 120 150 220 TPE 2V 330 TPE D2E(6) D2E(6) D2E(6) TPLF D2T(7,6) D2T(7,6) D2T(7,6) C(45) D3(65) B2(55) D3L(55) D2(45) D2(40) B2(70) TPB TPC C1(70) TPD 1500 D4(30) D4(30) D3L(40) D3L(40) D4D(*4) D4D(*4) D4D(*4) D2E(*3) D3L(*2) D4(*1) D3L(10,7) D3L(10,7,6) C2(15,12, 9) TPE TPE B2(35) TPE D2E(*3) D2E(*3) B2(35,25,21,18) B2(35) B2(15)* C3(*1) TPF D3L(7) TPG B1G(70) TPL D2T(12) TPU A09(150) TPU A09(150) TPB TPB 1000 B2(70) C(45) C(45) B2(70,45) B2(70) D3(65) C1(55) D2(45) D2(40) D2E(25,18) D2E(*1) B2(35,30) B2(35) TPB D3L(55) TPC D2T(12,9,8,7) D2T(12,9,8,7) D4(40) D3L(40) D3L(40) D2E(25,18) D3L(*2) D3L(12) D3L(10) D4(15,12) Products List TPE 3.15V 680 B2(15)* TPF TPB 2.5V 470 B2(18) D4(35) TPC TPD D4D(10) TPE TPE 4V B2(35) TPE C2(18,15) TPE C3(25,18) TPF TPG B1G(70) TPU B09(70) TPU A09(150) D4(*1) B15G(70) APC APD TPB B2(70) B2(55, 45) D3(55) TPB D3L(55) TPB TPC C(45) C1(55) D3L(40) D4(40) D2(45) D2(40) D2(40) D2E(25,18) D2E(25,18) D2E(25,18) D2E(25) C3(25) D2E(25) D3L(25,18) C2(25,18) C3(25) TPD D4D(10) TPE TPE TPE TPE B2(35,25) B2(35) B1G(70) B1G(70) D4(25,18) D4(25,18) B2(35) TPF TPG D4(35) C1(55) TPC 6.3V D3L(40) C(45) D3L(12) D3L(9) D4(40) D4(35) B15G(70) TPU TPU APC APD TPB C(45) TPC 8V D2(40) TPE C2(25) TPG TPU TPB C(55) TPB 10V D3(55) D3L(55) TPC D2(45) TPE D2E(25) TPF D3L(40) D3L(40) C3(55) D3L(25) D2(45) D4(25) D3L(15) TPG TPU TPC 12.5V TPG TQC 16V D3L(50) TQC 20V TQC 25V TQC 7 Guidelines and Precautions for Use Solid Electrolytic Capacitors with Polymerized Organic Semiconductor POSCAP is uniquely structured solid electrolytic capacitor. Please note the following points in order to take full advantage of the POSCAP's performance and ensure the most stable quality possible. Crucial Precautions (1) Polarity POSCAP is a conductive polymer capacitor with positive and negative electrodes. Do not reverse the polarity when using. If it is used with the polarities reversed, increased leakage current or a short circuit may result. (2) Prohibited circuits Since problems can be expected, the POSCAP cannot be used on the following circuits. (1) High impedance voltage retention circuits (2) Coupling circuits (3) Time constant circuits Guidelines and Precautions for Use (4) Circuits greatly affected by leakage current (5) The circuit in which two or more POSCAP are connected in a series so as to raise the endurance voltage. (3) Over voltage prohibited during design Over voltage exceeding the rated voltage may not be applied even for an instant as it may cause a short circuit. (4) Sudden charge and discharge restricted Sudden charge and discharge are restricted (for maintainance of high-proof reliability). A protection circuit is recommended for when a sudden charge or discharge causes excessive rush current since this is main cause of short circuit and large leakage current. Use protection circuits in case the rush current value exceeds 20A. Be sure to insert a protection resistor of about 1k for charge and discharge when measuring the leakage current. (5) Considerations when soldering The soldering conditions are to be within the range prescribed in this delivery specification. If the specifications are not followed, there is the possibility of the appearance becoming defective when soldering is conducted under conditions that are harsher that those stipulated. (6) Considerations when using in industrial equipment To insure reliability when POSCAP is used in industrial equipment, allow wider margin of capacitance, impedance and other characteristics. (7) Using in equipment regarding human life In case of using in equipment regarding human life (e.g. Space equipment, aeronautic equipment, military equipment and atomic equipment etc.), be sure to talk over the matter with SANYO. Don't use without a recognition document of SANYO. Circuit designing cautions (1) Check the rated performance After checking the operation and installation environments, design the circuit so that it falls whithin the rated performance range stipulated in this delivery specification. (2) Operating temperature and ripple current (a) Set the operating temperature so that it falls whithin the range stipulated in this delivery specification. (b) Do not supply current that exceeds the allowable ripple current. When excessive ripple current is supplied, internal heat increases and reduces the POSCAP's life span. 8 Guidelines and Precautions for Use Solid Electrolytic Capacitors with Polymerized Organic Semiconductor (3) Leakage current Even when the soldering conditions fall whithin the range of this delivery specifications, leakage current increases a little on occasion. It also increases a little during high temperature storage, high humidity storage and temperature cycling with no voltage applied. In cases such as these, leakage current will decrease by applying voltage under the condition of below the POSCAP's maximum operating temperature. The speed at which the leakage current is restored is increased by applying voltage when the POSCAP's temperature is close to the maximum operating temperature. (4) Applied voltage for designing (a) Less than 90% of the rated voltage or category voltage is recommended. If the rated voltage is 10V, and over less than 80% of the rated voltage or category voltage is recommended. (b) The sum of the DC voltage plus the peak AC voltage shall not exceed the rated voltage or category voltage. (c) The sum of the DC voltage plus the negative peak AC voltage shall not allow a voltage reversal. (5) Reduction of failure stress Guidelines and Precautions for Use When POSCAP is used within the rated voltage , it shows a stable characteristic, but it may be damaged in a short circuit when an overvoltage, for instance, is applied. The time to reach the failure mode can be extended by using POSCAP with reduced ambient temperature, ripple current and applied voltage. [Failure rate] In the case of the endurance which is 105Cx2,000h. 0.5%/1,000h (Environment temp. : 105C, Rated voltage or Category voltage applied) In the case of the endurance which is 105Cx1,000h or 125Cx1,000h. 1.0%/1,000h (Environment temp. : 105C, Rated voltage or Category voltage applied) In the case of the endurance which is 85Cx1,000h. 1.0%/1,000h (Environment temp. : 85C, Rated voltage applied) (6) Operating environment restrictions Do not use the POSCAP in the following environments. (a) Places where water, salt water or oil can directly fall on it and places where condensation may form. (b) Places filled with noxious gas for capacitors (hydrogen sulfide, sulforous acid, chlorine, ammonia, etc.). (c) Places susceptible to ozone,ultraviolet rays and radiation. (7) Land pattern When mounting the POSCAP on the PC board, match the POSCAP's land pattern dimension. (See P16.) (8) Parallel connection A large amount of ripple current may be applied to the POSCAP when it is used in parallel connection with another capacitor. Carefully select the type of capacitor. (9) Protect circuit The failure mode of POSCAP is the short mode. When it breaks down, short electric current flows to it. POSCAP gives off heat by this short current. Do the following consideration in design fully for the safety because it has a bad influence on the part around POSCAP due to this heat. : A protection circuit and a protection device are set up, and it is made safer as a system. : A diffuse circuit and so on is set up, and a safe system is taken so that a machine may not break down as to the single trouble. (10) Others Design circuits after checking the following items. Electrical characteristics are affected by temperature and frequency fluctuations. Design circuits after checking the amount of fluctuation. We are confident that the practical configurations and examples listed in this document will ensure the maximum benefit from the characteristics and performance features of our products and that these application examples are accurate and reliable. However, we cannot accept any liability for any problems in connection with industrial property rights and concerning any difficulties arising in the use of these circuits. It should also be noted that as part of our ongoing policy of product improvement, the specifications given herein may be changed or modified at any time without prior notice. Copyright, All or portions of this publication are protected against copying or other reproduction. Company name of a mention and product name are the trademark of each company or trade mark. 9 Guidelines and Precautions for Use Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Storage Conditions It is necessary to set an environment to prevent a trouble at the time of soldering by the degradation of solder ability or moisture's getting into the molding resin when POSCAP are stored. (1) Please make the storage of POSCAP sealing up in the reel and storage bag. (2) Do not store the POSCAP at high temperature and high humidity. Store it in a location that is not subject to direct sunlight, has temperatures less than 35C (Generally 15 to 35C), and relative humidity less than 75%RH (45 to 75%RH) generally. (3) The storage period is one year or shorter under the condition that it is un opened the storage bag. (TQC series : 9 months from the pass mark on the label) (4) Do not store the POSCAP in damp conditions such as with water, salt spray, or oil spray, and dew condensation. (5) Do not store the POSCAP in places filled with noxious gas (hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.). (6) Do not store the POSCAP in places susceptible to ozone, ultraviolet rays and radiation. Guidelines and Precautions for Use (7) Please unseal storage bag just before mounting and be conscious that POSCAP not remain. When remainder occurs reluctantly, return them to storage bag once again and, please seal the unsealing division by adhesive tape etc., including desiccants. More over, once open the strage bag, it should be followed the , table of (8) s Floor Life "Time" and "condtions". (8) The moisture level of POSCAP is the following. LEVEL Floor Life Time Applicable scope Conditions Size code Series TPB,TPC,TPE,TPD, TH*,TPL,TPLF TPB,TPC,TPE,TPG, TPU,TA,TQC (All sizes) 2a 4 weeks 30C/60%RH D2E,D2,D2T, D3L,D3,D4,D4D 3 168hours 30C/60%RH S08,S11,A09,B09, B1,B1G,B15G,B2,C1,C3,C,C2 4 72hours 30C/60%RH D2 APC 5 48hours 30C/60%RH D1,D2E,D2,D3L,D4 TH,APD (Conform to IPC/JEDEC J-STD-020C) Use at 105C or less NOTE:The model of MSL "2a" is changed into MSL "3" with the 260C reflow soldering. * Compensation coefficient of maximum allowable ripple current It takes advantage in ripple current value of characteristics list and the following coefficient. (For questions regarding TQC series, please ask separately.) Frequency compensation coefficient (TPB,TPC,TPD,TPE,TPF,TPG,TPL,TPLF,TPU,TA,THseries) 120Hzf<1kHz 1kHzf<10kHz 10kHzf<100kHz 100kHzf<1MHz 22FC100F 0.20 0.60 0.85 1.00 100FC330F 0.25 0.70 0.85 1.00 330FC1000F 0.30 0.75 0.90 1.00 Temperature compensation coefficient (TPB,TPC,TPD,TPE,TPF,TPG,TPL,TPLF,TPU,TA,TH,APseries) Case size code S08, S11, A09, B09, B1,B1G,B15G, B2, C, C1, C2, C3, D2, D2E, D2T, D3L, D3, D4(THD), D4D D4 T45C 1.00 1.00 45C<T85C 0.70 0.50 *85C<T105C 0.25 0.25 T :Environment temperature TH series :85C<T125C * 10 Environmental Consideration Solid Electrolytic Capacitors with Polymerized Organic Semiconductor RoHS Compliance POSCAP is compliant to the RoHS Directive(2002/95/EC), Restricted substances of RoHS directive Substance Lead (Pb) and it's compounds Cadmium (Cd) and it's compounds Mercury (Hg) and it's compounds Hexavalent chromium (Cr6+) Polybrominated biphenyls (PBBs) Polybromineted diphenyl ethers (PBDEs) Lead-Free Status All complete parts and homogenous materials of POSCAP are lead-free. TPG, TPL and TPU series are the halogen-free products which use non-halogen material as molding resin. We are planning to remove halogenated material from other series, too. Environmental Consideration Halogen-Free * Halogen-free POSCAP is also compliant with RoHS directive and lead-free. 11 Marking Solid Electrolytic Capacitors with Polymerized Organic Semiconductor C,C1,D2,D3,D4 size (TPB,TPC,TH series) C,D2,D3L size (TQC series) D1,D2 size (APC,APD series) C2,C3,D2E,D3L size (TPB,TPE,TPF series) D4,D4D size (TPD,TPE series) TPB series D3L size Rated capacitance 470 e 58 L Rated capacitance 680 e 57 Anode(+) Anode(+) Lot. No. 2 * L TPF series F TRD series D Lot. No. 2 * Rated voltage 1 Rated voltage 1 * * B09,B1,B1G,B15G,B2 size B2 size (TPE series) (TPB,TPG,TPU,TQC series) Rated capacitance 3 * Rated capacitance 3 * S7 j G Marking Anode(+) E8 e F Anode(+) Lot. No. 2 * Rated voltage 1 * S08,S11,A09 size (TPU series) D2T size (TPL,TPLF series) Rated capacitance 3 j AH 330 e 55 T * Anode(+) Anode(+) * * * * Rated capacitance 4 Rated voltage 1 Lot. No. 2 Rated voltage 1 Lot. No. 2 * T TPLF series F Lot. No. 2 * Rated voltage 1 * *1 The rated voltage is as follows. R.V. Mark 2.0 2.5 3.15 4.0 6.3 8.0 10 12.5 16 d e f g j K *2 Lot.No.shows roughly manufacturing date. *3 The rated capacitance is as follows. Capacitance(F) 5.6 8.2 10 Mark U6 Y6 A7 25 C 1E(orE) A B 68 100 120 150 220 330 22 33 47 56 J7 N7 S7 U7 W7 A8 C8 *4 The rated capacitance is as follows. 12 TPL series R. Cap.(F) 10 15 22 33 47 68 100 Mark A E J N S W A E8 J8 N8 Explanation of Part Numbers Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Use the following example to define POSCAP part numbers. 2R5 TPB 330 M L Rated voltage 1 to 3 figures Series name 3 figures Rated capacitance 2 to 4 figures Capacitance tolerance 1 figure Special code 0 to 3 figures Code Series Code Rated capacitance Code Capacitance tolerance Code 2.0 2 TPB Series TPB 5.6 5R6 20% M 2.5 2R5 TPC Series TPC 8.2 8R2 3.15 3 TPD Series TPD 10 10 4.0 4 TPE Series TPE 15 15 6.3 6 TPF Series TPF 22 22 8.0 8 TPG Series TPG 33 33 10 10 TPL Series TPL 47 47 12.5 12 TPLF Series TPLF 56 56 16 16 TPU Series TPU 68 68 20 20 TAB Series TAB 82 82 TAC Series TAC 100 100 TAD Series TAD 150 150 TAE Series TAE 220 220 THB Series THB 330 330 THC Series THC 470 470 THD Series THD 680 680 THE Series THE 1000 1000 TQC Series TQC 1500 1500 APC Series APC APD Series APD 25 25 Standard Code Standard TPE Series B2 size C2 size C3 size D2E size D3L size ESR 35m Max. ESR 30mMax. ESR 25m Max. ESR 21m Max. ESR 18m Max. ESR 15m Max. ESR 15m /300KHz Max. ESR 35m Max. 85C ESR 30m Max. 85C ESR 25m Max. 85C ESR 15m Max. 85C ESR 15m /300KHz Max. 85C ESR 25m Max. ESR 18m Max. ESR 15m Max. ESR 12m Max. ESR 9m Max. ESR 55m Max. ESR 35m Max. ESR 25m Max. ESR 18m Max. ESR 15m Max. ESR 25m Max. 85C ESR 25m Max. ESR 18m Max. ESR 15m Max. ESR 12m Max. ZB UB PB LB IB FB FGB AZB AUB APB AFB AFGB PC2 IC2 FC2 CC2 9C2 GC ZC PC IC FC AP L IL FL CL Explanation of Part Numbers Rated voltage B2 Size D3L Size TPB Series 85C ESR 45m Max. ESR 45m Max. 85C C size D3L size TPC Series B1 size C1 size TPF Series ESR 9m Max. ESR 7m Max. TPU Series S11 size A09 size B09 size All Series ESR 45m Max. ESR 35m Max. ESR 18m Max. ESR 15m Max. ESR 12m Max. ESR 09m Max. ESR 08m Max. ESR 06m Max. ESR 05m Max. Code A V AV C L B C 9L 7L SK AI BI V Z I F C 9 8 6 5 13 Structure Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPB,TPC,TPE,TPF,TQC,TA,TH series Sintered Tantalum Ag-paint layer Silver paint Carbon layer Mold resin Conductive Polymer Tantalum oxide layer Cathode(-) Anode(+) TPL,TPLF series Conductive Polymer Sintered Tantalum Ag-paint layer Carbon layer Mold resin Silver paint Tantalum oxide layer Cathode(-) TPU series Sintered Tantalum Ag-paint layer Anode(+) Carbon layer Structure Mold resin Silver paint Cathode(-) Conductive Polymer Tantalum oxide layer Anode(+) AP series Aluminum foil Silver paint Ag-paint layer Conductive Polymer Mold resin Metal foil Insulation adhesive Aluminum oxide layer Cathode(-) Anode(+) 14 Taping Specifications Solid Electrolytic Capacitors with Polymerized Organic Semiconductor We supply only embossed taping type. * Dimension of carrier tape Sprocket hole Component compartment J E (Polarity) A B C D (-) (+) t F K G H Direction of unreeling (unit:mm) J K t +0.1 code 0.1 0.1 0.3 0.1 0.1 0.1 0.1 0.1 -0 0.2 0.1 Size A B C D E F G H Packing quantities Size code Pieces/reel(180) Pieces/reel(330) S08 4000 -- S11 3000 -- A09 3000 -- B09 3000 -- B1 3000 -- B1G 2500 -- B15G 2500 -- B2 2000 -- C1 -- 4000 C2 -- 3000 C3 -- 2500 C -- 2500 D1 -- 3000 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.0 0.25 D2E -- 3000 S11 1.45 2.25 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.3 0.25 D2T -- 3000 A09 2.05 3.65 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.3 0.25 D2 -- 3000 B09 3.2 3.8 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.4 0.2 D3L -- 2500 B1 3.8 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.4 0.2 D3 -- 2500 B1G 3.25 3.9 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.7 0.25 D4 -- 2000 B15G 3.25 3.9 8.0 3.5 1.75 4.0 2.0 4.0 1.5 1.7 0.25 D4D -- 2000 B2 3.3 3.8 8.0 3.5 1.75 4.0 2.0 4.0 1.5 2.1 0.2 C1 3.7 6.4 12.0 5.5 1.75 8.0 2.0 4.0 1.5 1.7 0.3 C2 3.7 6.4 12.0 5.5 1.75 8.0 2.0 4.0 1.5 2.1 0.3 C3 3.7 6.4 12.0 5.5 1.75 8.0 2.0 4.0 1.5 2.9 0.3 C 3.7 6.4 12.0 5.5 1.75 8.0 2.0 4.0 1.5 3.2 0.3 D1 4.55 7.65 12.0 5.5 1.75 8.0 S08 1.65 2.4 3.2 2.0 4.0 1.5 1.6 0.3 D2E 4.5 7.5 12.0 5.5 1.75 8.0 2.0 4.0 1.5 2.4 0.3 D2T 4.5 7.8 12.0 5.5 1.75 8.0 2.0 4.0 1.5 2.4 0.3 Dimension of packing case b 4.5 7.5 12.0 5.5 1.75 8.0 2.0 4.0 1.5 2.4 0.3 D3L 4.5 7.7 12.0 5.5 1.75 8.0 2.0 4.0 1.5 3.2 0.3 D3 4.5 7.5 12.0 5.5 1.75 8.0 2.0 4.0 1.5 3.5 0.3 D4 4.5 7.7 12.0 5.5 1.75 8.0 2.0 4.0 1.5 4.2 0.3 Reel size D4D 4.5 7.7 12.0 5.5 1.75 8.0 2.0 4.0 1.5 4.2 0.3 D2 A B C Reel dimension W1 W2 (unit:mm) c (unit:mm) 180 330 a 90 120 b 240 360 c 240 360 Units per packing case Size code Pieces/case S08 20000 S11 15000 A09 15000 B09 15000 B1 15000 B1G 12500 B15G 12500 B2 10000 C1 20000 C2 15000 C3 12500 C 12500 D1 15000 D2E 15000 D2T 15000 D2 15000 D3L 12500 A B C W1 W2 D3 12500 3302 802 130.2 13.50.5 17.51.0 D4 10000 180+0 -3 602 130.2 90.5 11.41.0 D4D 10000 Taping Specifications *Dimension A and B are the measure of compartment's inside bottom. *The (+) Polarity of the chip is placed on right side towards the unreeling direction. *Dimension of the topcover tape Thickness of cover tape: 6210m Width of cover tape: 9.50.2mm 5.50.2mm (180reel) a 15 Recommended Land Pattern Dimension Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Except for TPL/TPLFseries b (unit:mm) a c a Size code a b c S08 1.0 0.9 0.6 S11 1.0 0.9 0.6 A09 1.6 1.2 1.2 B09 1.6 2.7 1.4 B1 1.6 2.7 1.4 B1G 1.6 2.7 1.4 B15G 1.6 2.7 1.4 B2 1.6 2.7 1.4 C1 2.4 2.3 2.4 C2 2.4 2.3 2.4 C3 2.4 2.3 2.4 C 2.4 2.3 2.4 D1 2.4 2.9 3.7 D2E 2.4 2.9 3.7 D2 2.4 2.9 3.7 D3L 2.4 2.9 3.7 D3 2.4 2.9 3.7 D4 2.4 2.9 3.7 D4D 2.4 2.9 3.7 TPL/TPLFseries A F C A G B VIA(-) 8-0.4 Recommended Land Pattern Dimension Q J R I E D H VIA(+) 8-0.4 M K * Slash areas shows solder pads M L N O P (1) Three-pad design for three-terminal model (TPL/TPLF series) (unit:mm) Size code A B C D E F G H I J K L M N O P Q R D2T 1.7 1.2 2.7 3.2 5.1 0.7 1.3 0.45 0.9 0.75 0.9 1.1 0.3 1.4 1.0 2.15 0.95 2.1 (2) Common three-pad design for POSCAP D-size two-terminal model 16 Size code A B C D E F G H I J K L M N O P Q R D common 2.2 1.2 2.7 2.9 5.1 0.5 1.0 0.45 0.9 0.75 1.4 1.1 0.3 1.4 1.0 2.15 0.95 2.1 Recommended Soldering Condition Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Recommended reflow soldering temperature profile Temperature on the surface of capacitor The cycles of reflow soldering: Twice (Max.) Peak temperature 5s max. 240C 200C 40s max. 150C 60s max. 120s max. 30s max. Time(sec.) Peak temperature 250C lead free reflow soldering profile Temperature on the surface of capacitor The cycles of reflow soldering: Twice (Max.) Peak temperature 5s max. 250C 220C 40s max. 180C 150C 60s max. 120s max. 30s max. Time(sec.) Peak temperature 260C lead free reflow soldering profile * The model of MSL"2a" is changed into MSL "3" with this reflow condition.(See P10) The cycles of reflow soldering: Twice (Max.) Peak temperature 260C 217C 200C 150C 60s max. 180s max. 90s max. 6s max. Recommended Soldering Condition Temperature on the surface of capacitor 5s max. Time(sec.) Soldering with a soldering iron Tip of a soldering iron: 350C Max. Power of a soldering iron: 30W Max. Working time: 3sec. Max. (Do not let the tip of soldering iron touch the POSCAP itself. Do not subject the POSCAP itself to excessive stress when soldering.) 17 Characteristics Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Temperature Characteristics Temperature Characteristics (ESR) Temperature Characteristics(Cap.) 100 200 80 150 60 Capacitance change (%) ESR change (%) 100 50 0 -50 -100 40 20 0 -20 -40 -60 -150 -80 -200 -55 -35 -15 5 25 45 Temperature(:) 65 85 105 MLCC 10F16V Y5V 3.2x2.5x1.15mm 6TPB47M Bias voltage Characteristics Bias voltage Characteristics (Cap.) 100 80 Capacitance change (%) 60 40 20 0 -20 -40 -60 -80 -100 0 Characteristics 18 2 4 Bias Voltage (V) 6 MLCC 10F16V Y5V 3.2x2.5x1.15mm 6TPB47M -100 -55 -35 -15 5 25 45 Temperature(:) 65 85 105 MLCC 10 F16V Y5V 3.2x2.5x1.15mm 6TPB47M Characteristics Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Frequency Characteristics TPD series TPE series 100 100 ESR, Impedance() 10 1 0.1 2R5TPD470M5(2.5V/470F)_Imp. 2R5TPD470M5(2.5V/470F)_ESR 2R5TPD680M5(2.5V-680F)_Imp. 2R5TPD680M5(2.5V-680F)_ESR 10 ESR, Impedance() B2size(6TPE100MAZB)_Imp. B2size(6TPE100MAZB)_ESR C3size(6TPE150MPC)_Imp. C3size(6TPE150MPC)_ESR D2Esize(6TPE150MI)_Imp. D2Esize(6TPE150MI)_ESR D3Lsize(6TPE330MIL)_Imp. D3Lsize(6TPE330MIL)_ESR D4size(6TPE470MI)_Imp. D4size(6TPE470MI)_ESR 1 0.1 0.01 0.01 0.001 0.001 0.1 1 10 100 Frequency(kHz) 1000 10000 0.1 SIZE:D4 L W H 7.3x4.3x3.8 1 2R5TPE330M9 vs 2R5TPL330M9 1000 10000 100 2R5TPE330M9(2.5V/330F)_Imp. 2R5TPE330M9(2.5V/330F)_ESR 2R5TPL330M9(2.5V/330F)_Imp. 2R5TPL330M9(2.5V/330F)_ESR 6TPU22M(6.3V/22F)_Imp. 6TPU22M(6.3V/22F)_ESR 10 ESR, Impedance() 10 ESR, Impedance() 100 6TPU22M ; S11 size 100 1 0.1 0.01 1 0.1 0.01 0.001 0.001 0.1 1 10 100 Frequency(kHz) 1000 10000 0.1 SIZE:S11 L W H 2.0x1.25x1.1 2R5TPLF470M7 vs 2R5TPF470M7L 1 10 100 Frequency(kHz) 1000 10000 TQC series 100 100 2R5TPLF470M7(2.5V/470F)_Imp. 2R5TPLF470M7(2.5V/470F)_ESR 2R5TPF470M7L(2.5V-470F)_Imp. 2R5TPF470M7L(2.5V-470F)_ESR 0.1 0.01 1 0.1 Characteristics 1 B2size(25TQC5R6M) Imp. B2size(25TQC5R6M) ESR Csize(25TQC10M) Imp. Csize(25TQC10M) ESR D2size(25TQC15M) Imp. D2size(25TQC15M) ESR D3Lsize(25TQC33M) Imp. D3Lsize(25TQC33M) ESR 10 ESR, Impedance() 10 ESR, Impedance() 10 Frequency(kHz) 0.01 0.001 0.001 0.1 1 10 100 Frequency(kHz) 1000 10000 0.1 1 10 100 Frequency(kHz) 1000 10000 19 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPBSeries Standard Products Fe a tu re TPB series are the standard products corresponding to the diversification of the needs. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 47 to 1000 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ Operating Temperature range Rated voltage Dissipation Factor (D.F.) Leakage current -- 2.5 to 10.0 (V.DC) 120Hz/20C 8.0 or 10.0 or 15.0 (%) Rated voltage applied, after 5 minutes 0.1CV (A) Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C -55C Z/Z20C +105C Z/Z20C 105C,2000h, rated voltage applied Endurance 1.0 to 2.0 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit Within+50%,-20% of the initial value (2R5TPB1000M) C/C 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 105C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge Within+40%, -20% of the initial value (Except for the above model) D.F. Dimensions 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) W F 2.5 (3.2) 4.0 (5.0) 6.3 (8.0) C 68 C H 150 (unit: mm) T P B Size L*1 W H S W1 code (0.2) (0.2) (0.2) (0.2) (0.1) C 6.0 3.2 2.8 1.3 1.8 D3L 7.3 4.3 2.8 1.3 2.4 D3 7.3 4.3 3.1 1.3 2.4 D4 7.3 4.3 3.8 1.3 2.4 *1 0.3:D3L,D4 20 C 100 W1 S 10.0 (13.0) 47 82 S 8.0 (10.0) C D3,D3L C C,D3,D3L D3L 220 C C,D3,D3L D3L D3L,D4 330 D3,D3L D3L D3L,D4 D4 470 D3L D4,D3L D4 680 D4,D3L D4 1000 D4 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number E.S.R. Maximum allowable Rated Rated Rated Category Category L.C. MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (V) (C) (F) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 10TPB68MC 10.0 105 68 10.0 105 8.0 68.0 55 1500 10TPB47MC 10.0 105 47 10.0 105 8.0 47.0 55 1500 8TPB82MC 8.0 105 82 8.0 105 8.0 65.6 45 1700 6TPB150MC 6.3 105 150 6.3 105 8.0 94.5 45 1700 6TPB100MC 6.3 105 100 6.3 105 8.0 63.0 45 1700 4TPB220MC 4.0 105 220 4.0 105 8.0 88.0 45 1700 4TPB150MC 4.0 105 150 4.0 105 8.0 60.0 45 1700 2R5TPB220MC 2.5 105 220 2.5 105 8.0 55.0 45 1700 10TPB220ML 10.0 105 220 10.0 105 10.0 220.0 40 2000 10TPB150ML 10.0 105 150 10.0 105 10.0 150.0 40 2000 10TPB100ML 10.0 105 100 10.0 105 8.0 100.0 55 1900 6TPB330ML 6.3 105 330 6.3 105 10.0 207.9 40 2000 6TPB220ML 6.3 105 220 6.3 105 10.0 138.6 40 2000 6TPB150ML 6.3 105 150 6.3 105 8.0 94.5 55 1900 4TPB470ML 4.0 105 470 4.0 105 10.0 188.0 40 2000 4TPB330ML 4.0 105 330 4.0 105 10.0 132.0 40 2000 4TPB220ML 4.0 105 220 4.0 105 8.0 88.0 55 1900 2R5TPB680ML 2.5 105 680 2.5 105 10.0 170.0 40 2000 2R5TPB470ML 2.5 105 470 2.5 105 10.0 117.5 40 2000 2R5TPB330ML 2.5 105 330 2.5 105 8.0 82.5 55 1900 10TPB100M 10.0 105 100 10.0 105 8.0 100.0 55 1900 6TPB150M 6.3 105 150 6.3 105 8.0 94.5 55 1900 4TPB220M 4.0 105 220 4.0 105 8.0 88.0 65 1500 2R5TPB330M 2.5 105 330 2.5 105 8.0 82.5 65 1500 10TPB330M 10.0 105 330 10.0 105 10.0 330.0 35 3000 10TPB220M 10.0 105 220 10.0 105 10.0 220.0 40 3000 6TPB470M 6.3 105 470 6.3 105 15.0 296.1 35 3000 6TPB330M 6.3 105 330 6.3 105 10.0 207.9 40 3000 4TPB680M 4.0 105 680 4.0 105 15.0 272.0 35 3000 4TPB470M 4.0 105 470 4.0 105 10.0 188.0 40 3000 2R5TPB1000M 2.5 105 1000 2.5 105 15.0 250.0 30 3000 2R5TPB680M 2.5 105 680 2.5 105 10.0 170.0 40 3000 C D3L D3 D4 3 2a *1 100k to 500kHz,45C T P B 21 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPBSeries Standard Products (B2 Size) Fe a tu re B2 size is the miniaturized version of TPB series. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 33 to 220 (F) Capacitance tolerance 120Hz/20C M:20% -- 2.5 to 10 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 8.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristic list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristic list Temperature characteristics of Impedance ratio 100kHz/+20C Dissipation Factor (D.F.) Leakage current -55C Z/Z20C +105C Z/Z20C 105C,1000h, rated voltage applied Rated temp. 85C products: 85C,1000h,rated voltage applied Endurance * 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) Surge * 105C,1000 cycles, 1kdischarge resistance, surge voltage applied 6TPB100MA, 4TPB150MA, 2R5TPB220MA : 85C Dimensions 1.0 to 2.0 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit C/C Within+40%, -20% of the initial value D.F. 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) F 2.5 (3.2) 4.0 (5.0) W 33 47 B2 H 68 S 100 (unit: mm) T P B 22 B2 150 W1 S 6.3 (8.0) Size L W H S W1 code (0.2) (0.2) (0.1) (0.2) (0.1) B2 3.5 2.8 1.9 0.8 2.2 220 B2 B2 B2 B2 B2 B2 8.0 (10.0) 10.0 (13.0) B2 B2 B2 B2 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number B2 Rated Rated Rated Category Category L.C. E.S.R. Maximum allowable MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 10TPB47M 10.0 105 47 10.0 105 8.0 47.0 70 1100 10TPB33M 10.0 105 33 10.0 105 8.0 33.0 70 1100 8TPB47M 8.0 105 47 8.0 105 8.0 37.6 70 1100 8TPB33M 8.0 105 33 8.0 105 8.0 26.4 70 1100 6TPB100MA 6.3 85 100 5.0 105 8.0 63.0 55 1200 6TPB100MAV 6.3 85 100 5.0 105 8.0 63.0 45 1400 6TPB68M 6.3 105 68 6.3 105 8.0 42.8 70 1100 6TPB47M 6.3 105 47 6.3 105 8.0 29.6 70 1100 4TPB150MA 4.0 85 150 3.2 105 8.0 60.0 70 1100 4TPB100M 4.0 105 100 4.0 105 8.0 40.0 70 1100 4TPB100MV 4.0 105 100 4.0 105 8.0 40.0 45 1300 4TPB68M 4.0 105 68 4.0 105 8.0 27.2 70 1100 2R5TPB220MA 2.5 85 220 2.0 105 8.0 55.0 55 1200 2R5TPB100M 2.5 105 100 2.5 105 8.0 25.0 70 1100 3 3 *1 100k to 500kHz,45C T P B 23 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPCSeries Low Profile Products Fe a tu re TPC series has low profile and low ESR. TPC series aids in the miniaturization of any products. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 33 to 330 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ -- 2.5 to 10 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 10.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C Dissipation Factor (D.F.) Leakage current -55C Z/Z20C +105C Z/Z20C 105C,2000h,rated voltage applied C1 size:1000h Rated temp. 85C products: 85C, 2000h, rated voltage applied Endurance * 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 105C,1000 cycles, 1kdischarge resistance, surge voltage applied 6TPC330M:85C Surge * Dimensions 1.0 to 2.0 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit C/C Within+40%, -20% of the initial value D.F. 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) F 2.5 (3.2) 4.0 (5.0) 6.3 (8.0) 33 8.0 (10.0) 10.0 (13.0) W C1 56 C1 68 H 82 S C1 D2 D2 C1 100 C1 D2,C1 150 D2 D2 W1 S (unit: mm) T P C 24 Size L W H S W1 code (0.2) (0.2) (0.1) (0.2) (0.1) C1 6.0 3.2 1.4 1.3 1.8 D2 7.3 4.3 1.9 1.3 2.4 220 D2 330 D2 D2 D2 D2 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number C1 D2 Rated Rated Rated Category Category MSL L.C. E.S.R. Maximum allowable D.F. Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) ripplecurrent Reflow Reflow (mArms) (%max.) max./5min. 100kHz/20C Temp. Temp. (V) (V) (C) (F) (C) 100kHz*1 260C 250C 8TPC33M 8.0 105 33 8.0 105 10.0 26.4 70 1200 6TPC100MC 6.3 85 100 5.0 105 10.0 63.0 55 1300 6TPC68M 6.3 105 68 6.3 105 10.0 42.8 55 1300 4TPC100M 4.0 105 100 4.0 105 10.0 40.0 55 1300 4TPC56M 4.0 105 56 4.0 105 10.0 22.4 70 1200 2R5TPC82M 2.5 105 82 2.5 105 10.0 20.5 70 1200 10TPC100M 10.0 105 100 10.0 105 10.0 100.0 45 1700 10TPC68M 10.0 105 68 10.0 105 10.0 68.0 45 1700 8TPC150M 8.0 105 150 8.0 105 10.0 120.0 40 1900 6TPC330MA 6.3 85 330 5.0 105 10.0 207.9 40 1900 6TPC150M 6.3 105 150 6.3 105 10.0 94.5 40 1900 6TPC100M 6.3 105 100 6.3 105 10.0 63.0 45 1700 4TPC220M 4.0 105 220 4.0 105 10.0 88.0 40 1900 4TPC150M 4.0 105 150 4.0 105 10.0 60.0 45 1700 2R5TPC330M 2.5 105 330 2.5 105 10.0 82.5 40 1900 2R5TPC220M 2.5 105 220 2.5 105 10.0 55.0 45 1700 3 3 3 2a *1 100k to 500kHz,45C T P C 25 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPCSeries B1 Size Fe a tu re B1 size is miniaturized, low profile version of TPC series. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C 10 to 56 (F) _ 20% M:+ -- 2.5 to 12.5 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 10.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Dissipation Factor (D.F.) Leakage current Equivalent series resistance (E.S.R. mmax.) Please see the attached characteristics list 100kHz/20C Temperature characteristics of Impedance ratio 100kHz/+20C -55C Z/Z20C +105C Z/Z20C 85C,1000h, rated voltage applied or 105C,1000h, category voltage applied Endurance 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 85C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge 1.0 to 2.0 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit C/C Within+40%, -20% of the initial value D.F. 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit (unit: mm) Dimensions L Size code L (0.2) W (0.2) H (0.1) S (0.2) W1 (0.1) B1 3.5 2.8 1.1 0.8 2.2 W Size List RV (SV) F H 10 15 22 33 47 56 S W1 S 2.5 (3.2) 4.0 (5.0) 6.3 (8.0) 8.0 (10.0) 10.0 (13.0) 12.5 (16.0) B1 B1 B1 B1 B1 B1 B1 B1 Characteristics List Size SANYO code Part number T P C 12TPC15M 12TPC10M 10TPC33MB 8TPC22M B1 6TPC47MB 6TPC33M 4TPC47M 2R5TPC56M Rated Rated Rated Category Category L.C. E.S.R. Maximum allowable MSL D.F. (A) (mmax.) ripplecurrent Reflow Reflow Voltage Temperature Capacitance Voltage Temperature (mArms) (%max.) Temp. (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. (V) 260C 250C 12.5 12.5 10.0 8.0 6.3 6.3 4.0 2.5 85 85 85 85 85 85 85 85 15 10 33 22 47 33 47 56 10.0 10.0 8.0 6.3 5.0 5.0 3.2 2.0 105 105 105 105 105 105 105 105 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 18.8 12.5 33.0 17.6 29.6 20.8 18.8 14.0 80 80 70 70 70 70 70 70 800 800 1000 1000 1000 1000 1000 1000 3 3 *1 100k to 500kHz,45C 26 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPDSeries Low ESR . High Capacitance Products Fe a tu re TPD series has low ESR and high capacitance. It is the most suitable for the high frequency and high current switching power supply applications. Specifications Items Condition Characteristics Operating Temperature range -- Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C Rated voltage -- Dissipation Factor (D.F.) 120Hz/20C Leakage current Rated voltage applied, after 5 minutes Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Temperature characteristics of 100kHz/+20C Impedance ratio 105C,2000h, rated voltage applied Endurance Damp heat (Steady state) 60C,90 to 95%RH,500h, No voltage applied Surge 105C,1000 cycles, 1kdischarge resistance, surge voltage applied -55 to +105 (C) 470 to 1000 (F) _ 20% M:+ 2.5 to 6.3 (V.DC) 10.0 (%) Please see the attached characteristics list Please see the attached characteristics list -55C Z/Z20C 1.0 to 2.0 +105C 0.6 to 1.0 Z/Z20C _ 20% of the initial value Within+ C/C 1.5 times the initial limit D.F. The initial limit L.C. Within+40%, -20% of the initial value C/C 1.5 times the initial limit D.F. 3 times the initial limit L.C. _ 5% of the initial value Within+ C/C The initial limit D.F. 3 times the initial limit L.C. (unit: mm) Dimensions L (0.3) W (0.2) H (0.2) S (0.2) W1 (0.1) D4D 7.3 4.3 3.6 1.3 2.4 W L Size code Size List RV H (SV) S F 4.0 (5.0) 2.5 (3.2) 470 D4D 680 D4D 1000 D4D 6.3 (8.0) D4D W1 S D4D Characteristics List Size SANYO code Part number 6TPD470M 4TPD680M 2R5TPD1000M 2R5TPD1000M8 2R5TPD1000M6 D4D 2R5TPD1000M5 2R5TPD680M6 2R5TPD680M5 2R5TPD470M6 2R5TPD470M5 Rated Rated Rated Category Category L.C. E.S.R. Maximum allowable MSL D.F. Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) ripplecurrent Reflow Reflow (mArms) (%max.) Temp. (C) (F) (C) max./5min. 100kHz/20C 100kHz*1 Temp. (V) (V) 260C 250C 6.3 4.0 105 105 470 680 6.3 4.0 105 105 10.0 10.0 296.1 272.0 2.5 105 1000 2.5 105 10.0 250.0 2.5 105 680 2.5 105 10.0 170.0 2.5 105 470 2.5 105 10.0 117.5 10 10 10 8 6 5 6 5 6 5 4400 4400 4400 4900 5600 6100 5600 6100 5600 6100 3 2a *1 100k to 500kHz,45C T P D 27 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPESeries Low ESR Products (D2E, D3L, D4 Size) Fe a tu re TPE series has low ESR and can aid in the miniaturization of many products. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 68 to 1500 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ Operating Temperature range 2.5 to 10 (V.DC) -- Rated voltage 10.0 (%) 120Hz/20C Dissipation Factor (D.F.) ( ) *D4size: 15.0 % Rated voltage applied, after 5 minutes Please see the attached characteristics list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C Leakage current -55C Z/Z20C +105C Z/Z20C 105C,2000h, rated voltage applied Rated temp. 85C products: 85C, 1000h, rated voltage applied Endurance * _ 20% of the initial value Within+ D.F. 1.5 times the initial limit The initial limit Within+50%, -20% of the initial value (2R5TPE470M (I,F,C,9,7), 2R5TPE330M (I,F,C,9,7), 2R5TPE220M (I,F,C,9,7) ,2R5TPE1000M (I,F) ,2R5TPE1500M (F,C) C/C Within+40%, -20% of the initial value (Except for the above model) D.F. 105C,1000 cycles, 1k discharge resistance, surge voltage applied 6TPE330MAP,16TPE220MAP:85C Surge 0.6 to 1.0 C/C L.C. 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 1.0 to 2.0 * Dimensions 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) F 2.5 (3.2) 4.0 (5.0) W 68 D2E H 150 W1 S (unit: mm) T P E Size L W H*1 S W1 code (0.3) (0.2) (0.2) (0.2) (0.1) D2E 7.3 4.3 1.8 1.3 2.4 D3L 7.3 4.3 2.8 1.3 2.4 D4 7.3 4.3 3.8 1.3 2.4 * 28 1 0.1:D2E 10.0 (13.0) D2E 100 S 6.3 (8.0) D2E D2E 220 D2E D2E D2E D3L 330 D2E D2E D2E,D3L D4 470 D2E D3L D4 680 D3L D4 D4 1000 D4 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number 10TPE68M 6TPE330MAP 6TPE220MAP 6TPE220M 6TPE220MI 6TPE150M 6TPE150MI 6TPE100M 6TPE100MI 4TPE330M 4TPE330MI 4TPE220M 4TPE220MI 4TPE220MF 4TPE150M 4TPE150MI D2E 2R5TPE470M 2R5TPE470MI 2R5TPE470MF 2R5TPE470MC 2R5TPE470M9 2R5TPE470M7 2R5TPE330M 2R5TPE330MI 2R5TPE330MF 2R5TPE330MC 2R5TPE330M9 2R5TPE330M7 2R5TPE220M 2R5TPE220MI 2R5TPE220MF 2R5TPE220MC 2R5TPE220M9 2R5TPE220M7 10TPE220ML 6TPE330ML 6TPE330MIL 4TPE470ML 4TPE470MIL D3L 4TPE470MFL 4TPE470MCL 2R5TPE680ML 2R5TPE680MIL 2R5TPE680MFL 2R5TPE680MCL 10TPE330M 6TPE680M 6TPE680MI 6TPE470M 6TPE470MI 4TPE680M D4 4TPE680MI 4TPE680MF 2R5TPE1000M 2R5TPE1000MI 2R5TPE1000MF 2R5TPE1500MF 2R5TPE1500MC Rated Voltage (V) 10.0 6.3 6.3 Rated Rated Temperature Capacitance (C) (F) 105 68 85 330 85 220 Category Voltage (V) 10.0 5.0 5.0 L.C. E.S.R. Maximum allowable Category MSL D.F. current (A) (mmax.) ripple Temperature Reflow Reflow (mArms) (%max.) Temp. (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 10.0 68.0 105 25 2400 10.0 207.9 105 25 2400 10.0 138.6 105 25 2400 6.3 105 220 6.3 105 10.0 138.6 6.3 105 150 6.3 105 10.0 94.5 6.3 105 100 6.3 105 10.0 63.0 4.0 105 330 4.0 105 10.0 132.0 4.0 105 220 4.0 105 10.0 88.0 4.0 105 150 4.0 105 10.0 60.0 2.5 105 470 2.5 105 10.0 117.5 2.5 105 470 2.5 105 10.0 235.0 2.5 105 330 2.5 105 10.0 82.5 2.5 105 330 2.5 105 10.0 165.0 2.5 105 220 2.5 105 10.0 55.0 2.5 10.0 105 105 220 220 2.5 10.0 105 105 10.0 10.0 110.0 220.0 6.3 105 330 6.3 105 10.0 207.9 4.0 105 470 4.0 105 10.0 188.0 2.5 105 680 2.5 105 10.0 170.0 10.0 105 330 10.0 105 10.0 330.0 6.3 105 680 6.3 105 15.0 428.4 6.3 105 470 6.3 105 15.0 296.1 4.0 105 680 4.0 105 15.0 272.0 2.5 105 1000 2.5 105 15.0 250.0 2.5 105 1500 2.5 105 15.0 375.0 25 18 25 18 25 18 25 18 25 18 15 25 18 25 18 15 12 9 7 25 18 15 12 9 7 25 18 15 12 9 7 25 25 18 25 18 15 12 25 18 15 12 25 25 18 25 18 25 18 15 25 18 15 15 12 2400 2800 2400 2800 2400 2800 2400 2800 2400 2800 3100 2400 2800 2400 2800 3100 3500 3900 4400 2400 2800 3100 3500 3900 4400 2400 2800 3100 3500 3900 4400 2400 2400 2800 2400 2800 3100 3500 2400 2800 3100 3500 3000 3000 3500 3000 3500 3000 3500 3900 3000 3500 3900 3900 4400 1 100k to 500kHz,45C * 3 (*2) 3 (*2) 2a 3 (*2) 3 (*2) 2 Under evaluation * T P E 29 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPESeries Low ESR Products (C3,C2,B2 Size) Fe a tu re This products is the miniaturized version of TPE series. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 47 to 330 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ -- 2.5 to 10.0 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 8.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C Dissipation Factor (D.F.) Leakage current -55C Z/Z20C +105C Z/Z20C 105C,2000h,(B2size:1000h) rated voltage applied Rated temp. 85C products: 85C,1000h,rated voltage appiled Endurance * _ 20% of the initial value Within+ D.F. 1.5 times the initial limit The initial limit Within+50%, -20% of the initial value (2R5TPE220MAZB,2R5TPE330MAZB, 2TPE330MIB (MAFB,MAFGB),2R5TPE220MAPB,2R5TPE330MFC2 (CC2,9C2)) C/C Within+40%, -20% of the initial value (Except for the above model) D.F. 105C,1000 times,1kdischarge resistance,surge voltage applied Rated temp 85C products: 85C,1000 times Surge 0.6 to 1.0 C/C L.C. 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 1.0 to 2.0 * Dimensions 1.5 times the initial limit L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) F 2.0 (2.6) 2.5 (3.2) 4.0 (5.0) 6.3 (8.0) 8.0 (10.0) 47 10.0 (13.0) W B2 100 B2 H 120 S S 150 B2 B2 B2,C2,C3 220 B2 B2,C2,C3 C3 330 T P E Size L W H*1 S W1 code (0.2) (0.2) (0.1) (0.2) (0.1) B2 3.5 2.8 1.9 0.8 2.2 C2 6.0 3.2 1.8 1.3 1.8 C3 6.0 3.2 2.5 1.3 1.8 1 0.2:C3 * 30 C2 B2 W1 (unit: mm) B2 B2 B2,C2,C3 C3 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number Rated Rated L.C. E.S.R. Maximum allowable Rated Category Category MSL D.F. current Reflow Reflow (mmax.) ripple (A) Voltage Temperature Capacitance Voltage Temperature (mArms) (%max.) Temp. (C) (F) (C) max./5min. 100kHz/20C 100kHz*1 Temp. (V) (V) 260C 250C 10TPE47MAZB 10.0 85 47 8.0 105 8.0 47.0 35 1400 6TPE150MAZB 6.3 85 150 5.0 105 8.0 94.5 35 1400 6TPE120MAZB 6.3 85 120 5.0 105 8.0 75.6 35 1400 6.3 105 100 6.3 105 8.0 63.0 35 1400 25 1600 6TPE100MAZB 6.3 85 100 5.0 105 8.0 63.0 35 1400 2 6PTE100MAPB* 6.3 85 100 5.0 105 8.0 63.0 25 1600 4TPE220MAZB 4.0 85 220 3.2 105 8.0 88.0 35 1400 4.0 85 150 3.2 105 8.0 60.0 35 1400 30 1500 4TPE100MZB 4.0 105 100 4.0 105 8.0 40.0 35 1400 2R5TPE330MAZB 2.5 85 330 2.0 105 8.0 82.5 35 1400 35 1400 25 1600 2R5TPE220MLB 21 1700 2R5TPE220MIB 18 1800 15/300k 1800 15 2000 35 1400 2 6TPE100MZB* 2 6PTE100MPB* 4TPE150MAZB 4TPE150MAUB B2 2R5TPE220MZB 2R5TPE220MPB 2R5TPE220MFGB 2R5TPE220MAFB*2 2.5 105 220 2.5 8.0 105 55.0 2.5 105 220 2.5 105 8.0 110.0 2.5 85 220 2.0 105 8.0 110.0 2R5TPE220MAZB 2.5 85 220 2.0 105 8.0 55.0 25 1600 2R5TPE150MZB 2.5 105 150 2.5 105 8.0 37.5 35 1400 2TPE330MIB 2.0 105 330 2.0 105 8.0 132.0 18 1800 2.0 85 330 1.6 105 8.0 132.0 15/300k 1800 15 2000 25 2200 25 2200 18 2600 18 2600 15 2900 15 2900 12 3300 9 3700 2R5TPE220MAPB 2TPE330MAFGB 2 2TPE330MAFB* 8TPE100MPC2 8.0 105 100 8.0 105 8.0 80.0 6.3 105 150 6.3 105 8.0 94.5 4.0 105 220 4.0 105 8.0 88.0 6TPE150MPC2 6TPE150MIC2 C2 4TPE220MIC2 4TPE220MFC2 2R5TPE330MFC2 2R5TPE330MCC2 2.5 105 330 2.5 8.0 105 82.5 2R5TPE330M9C2 C3 10TPE150MGC 10.0 105 150 10.0 105 10.0 150.0 55 1500 6TPE220MPC 6.3 105 220 6.3 105 8.0 138.6 25 2400 6TPE150MPC 6.3 105 150 6.3 105 8.0 94.5 25 2400 4.0 105 220 4.0 105 8.0 88.0 25 2400 18 2800 25 2400 18 2800 15 3100 4TPE220MPC 4TPE220MIC 2R5TPE330MPC 2R5TPE330MIC 2.5 105 330 2.5 8.0 105 82.5 2R5TPE330MFC 1 100k to 500kHz,45C * 2 Under development * 3 3 (*3) 3 *3 Under evaluation T P E 31 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPFSeries Low ESR . High Capacitance Products Fe a tu re TPF series has low ESR and high capacitance at standard form. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C 150 to 680 (F) _ 20% M:+ -- 2.0 to 10.0 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 10.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Dissipation Factor (D.F.) Leakage current Equivalent series resistance (E.S.R. mmax.) Temperature characteristics of Impedance ratio Please see the attached characteristics list 100kHz/20C 100kHz/+20C -55C Z/Z20C +105C Z/Z20C 105C,2000h, rated voltage applied Endurance 1.0 to 2.0 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. C/C 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) L 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size code L (0.3) W (0.2) H*1 (0.1) S (0.1) W1 (0.1) D3L D2E 7.3 7.3 4.3 4.3 2.8 1.8 1.3 1.3 2.4 2.4 W RV (SV) H 150 220 330 470 680 W1 S Characteristics List T P F 32 10TPF150ML 6TPF330M9L 6TPF220ML 4TPF470ML 4TPF330ML D3L 2R5TPF680ML 2R5TPF680M7L 2R5TPF680M6L 2R5TPF470ML 2R5TPF470M7L 2R5TPF330M7L 2TPF470M6 D2E 2TPF330M6 2TPF220M6 *1 0.1:D2E Size List F Size SANYO code Part number 1.5 times the initial limit L.C. (unit: mm) Dimensions S Within+40%, -20% of the initial value (Except for the above model) D.F. 105C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge The initial limit Within+50%, -20% of the initial value (D2E size) 2.0 (2.6) 2.5 (3.2) 4.0 (5.0) 10.0 (13.0) 6.3 (8.0) D3L D2E D2E D2E D3L D3L D3L D3L D3L D3L D3L Rated Rated Rated Category Category L.C. E.S.R. Maximum allowable MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 10.0 6.3 6.3 4.0 4.0 2.5 2.5 2.5 2.5 2.5 2.5 2.0 2.0 2.0 105 105 105 105 105 105 105 105 105 105 105 105 105 105 150 330 220 470 330 680 680 680 470 470 330 470 330 220 10.0 6.3 6.3 4.0 4.0 2.5 2.5 2.5 2.5 2.5 2.5 2.0 2.0 2.0 105 105 105 105 105 105 105 105 105 105 105 105 105 105 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 150.0 207.9 138.6 188.0 132.0 170.0 170.0 170.0 117.5 117.5 82.5 188.0 132.0 188.0 15 9 12 10 12 10 7 6 10 7 7 6 6 6 3600 3900 4000 4400 4000 4400 4400 4400 4400 4400 4400 4400 4400 4400 3 2a (*2) *1 100k to 500kHz,45C *2 Under evaluation RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPGSeries Small Size . High Capacitance Products Fe a tu re TPG series is high capacitance model of the small size . low profile product. Suitable for the miniaturization design of the electronics device. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C 30 to 220 (F) _ 20% M:+ -- 2.5 to 12.5 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 10.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Dissipation Factor (D.F.) Leakage current Equivalent series resistance (E.S.R. mmax.) Please see the attached characteristics list 100kHz/20C Temperature characteristics of Impedance ratio 100kHz/+20C -55C Z/Z20C 1.0 to 2.0 +105C Z/Z20C C/C 0.6 to 1.0 _ 20% of the initial value Within+ D.F. 1.5 times the initial limit 85C,1000h, rated voltage applied or 105C,1000h, category voltage applied Endurance 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) The initial limit C/C Within+40%, -20% of the initial value D.F. 1.5 times the initial limit L.C. 3 times the initial limit _ 5% of the initial value Within+ C/C 85C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge L.C. D.F. The initial limit L.C. 3 times the initial limit (unit: mm) Dimensions Size code L W (+0.3/-0.1) (+0.3/-0.1) H (0.1) S (0.2) W1 (0.1) L 3.5 2.8 1.1 0.8 2.2 3.5 2.8 1.4 0.8 2.2 W B1G B15G Size List RV (SV) F H 33 47 68 100 150 220 S W1 S Characteristics List Size SANYO code Part number B15G 6TPG150M 4TPG220M 12TPG33M 10TPG47M 10TPG33M B1G 8TPG47M 6TPG100M 6TPG68M 4TPG150M 2R5TPG220M 2.5 (3.2) B1G 4.0 (5.0) B1G B15G 6.3 (8.0) 8.0 (10.0) 10.0 (13.0) 12.5 (16.0) B1G B1G B1G B1G B1G B1G B15G Rated Rated Rated Category Category E.S.R. Maximum allowable L.C. MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 6.3 4.0 12.5 10.0 10.0 8.0 6.3 6.3 4.0 2.5 85 85 85 85 85 85 85 85 85 85 150 220 33 47 33 47 100 68 150 220 5.0 3.2 10.0 8.0 8.0 6.4 5.0 5.0 3.2 2.0 105 105 105 105 105 105 105 105 105 105 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 94.5 88.0 41.3 47.0 33.0 37.6 63.0 42.8 60.0 55.0 70 70 70 70 70 70 70 70 70 70 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 3 3 *1 100k to 500kHz,45C T P G 33 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPL/TPLFSeries Low ESR . Low ESL Products Face Down Terminal Type Fe a tu re TPL series has a low ESL and low ESR advantage using an unique face down terminal structure. (back) Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 220 to 470 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ -- 2.0 to 2.5 (V.DC) Operating Temperature range Rated voltage 120Hz/20C 10.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C Dissipation Factor (D.F.) Leakage current -55C Z/Z20C +105C Z/Z20C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit C/C Within+50%, -20% of the initial value D.F. 1.5 times the initial limit 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 105C,1000 times, 1k discharge resistance, Surge voltage applied Surge Dimensions L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV 2.0 (2.6) 2.5 (3.2) 220 D2T D2T 330 D2T D2T 470 D2T D2T (SV) H W F S1 S2 W1 (-) S3 S4 (+) (unit: mm) T P L / T P L F 34 0.6 to 1.0 C/C 105C,2000h, rated voltage applied Endurance 1.0 to 2.0 Size L W H S1/S2 S3 S4 W1 code (0.3) (0.2) (0.1) (0.2) (0.1) (0.2) (0.1) D2T 7.3 4.3 1.8 1.1 1.1 2.3 2.8 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List (TPL) Size SANYO code Part number E.S.R. Maximum allowable Rated Rated Rated Category Category L.C. MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 2R5TPL470MC 2R5TPL470M9 117.5 2.5 105 470 2.5 105 10.0 2R5TPL470M8 235.0 2R5TPL470M7*2 D2T 2R5TPL330MC 2R5TPL330M9 82.5 2.5 105 330 2.5 105 10.0 2R5TPL330M8 165.0 2R5TPL330M7*2 2R5TPL220MC 2.5 105 220 2.5 105 10.0 55.0 12 3400 9 3900 8 4100 7 4400 12 3400 9 3900 8 4100 7 4400 12 3400 1 100k to 500kHz,45C * 3 2a *2 Under development (TPLF) Size SANYO code Part number D2T E.S.R. Maximum allowable Rated Rated Rated Category Category L.C. MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 260C Temp. 250C 2TPLF470M7 2.0 105 470 2.0 105 10.0 188.0 7 4400 2TPLF470M6 2.0 105 470 2.0 105 10.0 188.0 6 4700 2TPLF330M7 2.0 105 330 2.0 105 10.0 132.0 7 4400 2TPLF330M6 2.0 105 330 2.0 105 10.0 132.0 6 4700 2TPLF220M7 2.0 105 220 2.0 105 10.0 88.0 7 4400 2TPLF220M6 2.0 105 220 2.0 105 10.0 88.0 6 4700 3 2a *1 100k to 500kHz,45C T P L / T P L F 35 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TPUSeries Small Size . Low Profile Products Face Down Terminal Type Fe a tu re TPU series has a real advantage in size-sensitive applications using a face down terminal structure. Specifications Items Condition Characteristics Operating Temperature range -- 120Hz/20C Rated capacitance range 120Hz/20C Capacitance tolerance -- Rated voltage 120Hz/20C Dissipation Factor (D.F.) Rated voltage applied, after 5 minutes Leakage current 100kHz/20C Equivalent series resistance (E.S.R. mmax.) Temperature characteristics of 100kHz/+20C Impedance ratio 85C,1000h, rated voltage applied Endurance Damp heat (Steady state) 60C,90 to 95%RH,500h, No voltage applied Surge 85C,1000 times, 1k discharge resistance, Surge voltage applied -55 to +85 (C) 10 to 100 (F) _ 20% M:+ 2.5 to 10.0 (V.DC) 10.0 (%) Please see the attached characteristics list Please see the attached characteristics list -55C Z/Z20C 1.0 to 2.0 +85C 0.6 to 1.0 Z/Z20C _ 20% of the initial value Within+ C/C 1.5 times the initial limit D.F. The initial limit L.C. Within+40%, -20% of the initial value C/C D.F. 1.5 times the initial limit L.C. 3 times the initial limit _ 5% of the initial value C/C Within+ D.F. The initial limit L.C. 3 times the initial limit (unit: mm) Dimensions W L Size code L 1 (0.1)* W 1 (0.1)* H (0.1) S 1 (0.1)* W1 (0.1) S08 S11 A09 B09 2.0 2.0 3.2 3.5 1.25 1.25 1.6 2.8 0.8 1.1 0.9 0.9 0.5 0.5 0.8 0.8 0.9 0.9 1.2 2.2 *1 0.2:A09,B09 Size List RV H (SV) S F 10 15 22 33 47 68 100 W1 S 2.5 (3.2) 3.15 (4.0) 4.0 (5.0) 6.3 (8.0) 8.0 (10.0) 10.0 (13.0) B09 A09 S08 S08 S08 S11 S11 S11 A09,B09 A09,B09 A09 A09 Characteristics List Size SANYO code Part number T P U 36 6TPU10M S08 4TPU15M 2R5TPU22M 6TPU22MSK S11 4TPU33MSK 2R5TPU47MSK 10TPU33MAI 6TPU47MAI A09 4TPU68MAI 3TPU100MAI 2R5TPU100MAI 8TPU33MBI B09 6TPU47MBI 4TPU68MBI E.S.R. Maximum allowable Category Category L.C. Rated Rated Rated MSL D.F. ripple current (A) (mmax.) (mArms) Voltage Temperature Capacitance Voltage Temperature Reflow Reflow (%max.) Temp. (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. (V) 260C 250C 6.3 4.0 2.5 6.3 4.0 2.5 10.0 6.3 4.0 3.15 2.5 8.0 6.3 4.0 85 85 85 85 85 85 85 85 85 85 85 85 85 85 10 15 22 22 33 47 33 47 68 100 100 33 47 68 6.3 4.0 2.5 6.3 4.0 2.5 10.0 6.3 4.0 3.15 2.5 8.0 6.3 4.0 85 85 85 85 85 85 85 85 85 85 85 85 85 85 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 6.3 6.0 5.5 13.9 13.2 11.8 33.0 29.6 27.2 31.5 25.0 26.4 29.6 27.2 250 250 250 150 150 150 150 150 150 150 150 70 70 70 400 400 400 510 510 510 510 510 510 510 510 800 800 800 Under evaluation 3 3 *1 100k to 500kHz,45C RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TASeries High Reliability Products (For The Car Electronics) Fe a tu re TA series are high reliability products that the heat resistance and moisture resistance are improved. * Suitable for the industrial equipment or car electronics (e.g. Car navigation system). Specifications Items Condition Characteristics Operating Temperature range -- Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C Rated voltage -- Dissipation Factor (D.F.) 120Hz/20C Leakage current Rated voltage applied, after 5 minutes Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Temperature characteristics of 100kHz/+20C Impedance ratio Endurance 105C,2000h, rated voltage applied Damp heat (Load) 85C, 85%RH, 500h, rated voltage applied Damp heat (Steady state) 60C,90 to 95%RH,500h, No voltage applied Surge 105C,1000 cycles, 1kdischarge resistance, surge voltage applied Dimensions *1 L -55 to +105 (C) 47 to 680 (F) _ 20% M:+ 2.5 to 10 (V.DC) 10.0 (%) Please see the attached characteristics list Please see the attached characteristics list -55C Z/Z20C 1.0 to 2.0 +105C 0.6 to 1.0 Z/Z20C _ 20% of the initial value Within+ C/C 1.5 times the initial limit D.F. The initial limit L.C. Within+40%, -20% of the initial value C/C 1.5 times the initial limit D.F. The initial limit L.C. Within+40%, -20% of the initial value C/C 1.5 times the initial limit D.F. 3 times the initial limit L.C. _ 5% of the initial value Within+ C/C The initial limit D.F. 3 times the initial limit L.C. W B2 D2E D3L RV (SV) F H 47 68 100 150 220 330 470 680 W1 S Characteristics List Size SANYO code Part number B2 D2E D3L 10TAB47M 6TAB68M 6TAB47M 4TAB100M 10TAE68M 6TAE220M 6TAE220MI 6TAE150M 4TAE220M 4TAE220MI 2R5TAE470M 2R5TAE470MF 2R5TAE470MC 2R5TAE330M 2R5TAE330MI 2R5TAE330MF 2R5TAE330MC 2R5TAE220M 2R5TAE220MF 10TAE220ML 6TAE330ML 4TAE470ML 4TAE470MIL 2R5TAE680ML 2R5TAE680MFL *1 Within +50%, -20% of the initial value(2R5TAE470M(F,C), 2R5TAE330M(F,C), 2R5TAE220M(F,C)) (unit: mm) L*2 W H*1 S W1 Size (0.3) (0.2) (0.2) (0.2) (0.1) code 3.5 7.3 7.3 2.8 4.3 4.3 1.9 1.8 2.8 2.5 0.8 1.3 1.3 2.2 2.4 2.4 *1 0.1:D2E,B2 *2 0.2:B2 Size List S *1 4 6.3 10 B2 B2 B2 D2E D2E D2E D3L D3L B2 D2E D2E D2E D2E D3L D3L E.S.R. Maximum allowable Rated Category Category L.C. Rated Rated MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (V) (C) (F) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C 10.0 6.3 6.3 4.0 10.0 105 105 105 105 105 47 68 47 100 68 10.0 6.3 6.3 4.0 10.0 105 105 105 105 105 8.0 8.0 8.0 8.0 10.0 47.0 42.8 29.6 40.0 68 6.3 105 220 6.3 105 10.0 138.6 6.3 105 150 6.3 105 10.0 94.5 4.0 105 220 4.0 105 10.0 88 2.5 105 470 2.5 105 10.0 117.5 2.5 105 330 2.5 105 10.0 82.5 2.5 105 220 2.5 105 10.0 55 10.0 6.3 105 105 220 330 10.0 6.3 105 105 10.0 10.0 220.0 207.9 4.0 105 470 4.0 105 10.0 188 2.5 105 680 2.5 105 10.0 170 70 70 70 70 25 25 18 25 25 18 25 15 12 25 18 15 12 25 15 25 25 25 18 25 15 1100 1100 1100 1100 2400 2400 2800 2400 2400 2800 2400 3100 3500 2400 2800 3100 3500 2400 3100 2400 2400 2400 2800 2400 3100 3 3 *1 100k to 500kHz,45C T A 37 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor THSeries 125C Guaranteed Products (THB/THC/THD/THE series) Fe a tu re TH series has 125C capability guaranteed. It is the most suitable for the high reliability industrial equipment. Specifications Items Condition Series -- Operating Temperature range -- Rated capacitance range 120Hz/20C Capacitance tolerance 120Hz/20C THC 100 to 1000 (F) Equivalent series resistance (E.S.R. mmax.) 330 to 680 (F) 2.5 to 10 (V.DC) 2.5 to 10 (V.DC) 8.0 or 10.0 or 15.0 (%) 10.0 (%) 100kHz/20C 10.0 (%) Please see the attached characteristic list -55C Z/Z20C +125C Z/Z20C 1.0 to 2.0 0.6 to 1.0 _ 20% of the initial value Within+ C/C 2 times the initial limit tan 2 times the initial limit Within+50%, -20% of the initial value (2R5THB1000M) C/C 60C,90 to 95%RH,500h, No voltage applied Within+40%, -20% of the initial value (Except for the above model) 1.5 times the initial limit tan 105C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge 2.5 to 6.3 (V.DC) 2.5 to 6.3 (V.DC) 10.0 (%) L.C. Damp heat (Steady state) 150 to 330 (F) Please see the attached characteristic list 125C,1000h, category voltage applied Endurance 68 to 220 (F) -- 100kHz/20C Temperature characteristics of Impedance ratio THE _ 20% M:+ Rated voltage applied, after 5 minutes Leakage current THD -55 to +125 (C) 120Hz/20C Rated voltage Dissipation Factor (D.F.) Characteristics THB L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ The initial limit tan 3 times the initial limit L.C. Dimensions Size List L RV (SV) W F Series 2.5 (3.2) 4.0 (5.0) 6.3 (8.0) 10.0 (13.0) 68 THC D2 100 THB D3L 150 THC D2 THE D2E D3L D4 D4 D4 H THB 220 S S THC THE W1 THB (unit: mm) T H Size L*1 W H*2 S W1 code (0.3) (0.2) (0.1) (0.2) (0.1) 1.3 2.4 D2E 7.3 4.3 1.8 D2 7.3 4.3 1.9 1.3 2.4 D3L 7.3 4.3 2.8 1.3 2.4 D4 7.3 4.3 3.8 1.3 2.4 D4D 7.3 4.3 3.6 1.3 2.4 *1 0.2:D2 *2 0.2:D3L,D4,D4D 38 D2 330 470 680 1000 D2 D2E D3L D3L THD D4D THE D2E THB D3L THD D4 D4D THB D4 THD D4D THB D4 D4 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Series E.S.R. Maximum allowable Rated Rated Rated Category Category L.C. MSL Size SANYO D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow code Part number (%max.) Temp. (V) (C) (F) (V) (C) max./5min.100kHz/20C 100kHz*1 Temp. 260C 250C 10THB100ML 6THB220ML D3L 4THB330ML 2R5THB470ML 2R5THB330ML 10THB330M THB 10THB220M 6THB470M D4 6THB330M 4THB680M 2R5THB1000M 2R5THB680M 10THC68M 6THC150M THC D2 4THC220M 2R5THC220M 6THE150M 6THE150MI 4THE220M 4THE220MI THE D2E 4THE220MF 2R5THE330M 2R5THE330MI 2R5THE330MF 6THD330M THD D4 4THD470M 2R5THD680M 10.0 6.3 4.0 2.5 2.5 10.0 10.0 6.3 6.3 4.0 2.5 2.5 10.0 6.3 4.0 2.5 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 105 100 220 330 470 330 330 220 470 330 680 1000 680 68 150 220 220 6.3 4.0 2.5 1.6 1.6 6.3 6.3 4.0 4.0 2.5 1.6 1.6 6.3 4.0 2.5 1.6 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 8.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 10.0 15.0 15.0 10.0 10.0 10.0 10.0 10.0 100.0 138.6 132.0 117.5 82.5 330.0 220.0 296.1 207.9 272.0 250.0 170.0 68.0 94.5 88.0 55.0 6.3 105 150 4.0 125 10.0 94.5 4.0 105 220 2.5 125 10.0 88.0 2.5 105 330 1.6 125 10.0 82.5 6.3 4.0 2.5 105 105 105 330 470 680 4.0 2.5 1.6 125 125 125 10.0 10.0 10.0 207.9 188.0 170.0 55 40 40 40 55 35 40 35 40 35 30 40 45 40 40 45 25 18 25 18 15 25 18 15 10 10 10 1900 2000 2000 2000 1900 3000 3000 3000 3000 3000 3000 3000 1700 1900 1900 1700 2400 2800 2400 2800 3100 2400 2800 3100 4400 4400 4400 Under evaluation 5 *1 100k to 500kHz,45C T H 39 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TRSeries High Moisture Resistance Products Fe a tu re TR series are improved model of the moisture resistance more than standard products. Suitable for the industrial equipment. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 33 to 680 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ Operating Temperature range Rated voltage Dissipation Factor (D.F.) -- 2.5 to 10 (V.DC) 120Hz/20C 10.0 (%) *B2size: 8.0 (%) D4size: 15.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Equivalent series resistance (E.S.R. mmax.) 100kHz/20C Please see the attached characteristics list Temperature characteristics of Impedance ratio 100kHz/+20C Leakage current -55C Z/Z20C +105C Z/Z20C 105C,2000h,(B2size:1000h) rated voltage applied Rated temp. 85C products: 85C,1000h,rated voltage appiled Endurance * 0.6 to 1.0 C/C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit Within+50%, -20% of the initial value (2R5TRE220MAZB, 2R5TRE470M (F,C), 2R5TRE330M (F,C), 2R5TRE220M (F,C)) C/C 85C, 85%RH, 500h, rated voltage applied Damp heat (Load) 1.0 to 2.0 Within+40%, -20% of the initial value (Except for the above model) 1.5 times the initial limit D.F. The initial limit L.C. Within+50%, -20% of the initial value (2R5TRE220MAZB, 2R5TRE470M (F,C), 2R5TRE330M (F,C), 2R5TRE220M (F,C)) C/C 60C,90 to 95%RH,500h, No voltage applied Damp heat (Steady state) 105C,1000 times,1kdischarge resistance,surge voltage applied Rated temp. 85C products:85C Surge Within+40%, -20% of the initial value (Except for the above model) 1.5 times the initial limit D.F. * Dimensions L.C. 3 times the initial limit C/C _ 5% of the initial value Within+ D.F. The initial limit L.C. 3 times the initial limit Size List L RV (SV) F 2.5 4 6.3 W 33 B2 47 B2 68 D2E H B2 100 S W1 S T R Size L*1 W H*2 S W1 code (0.3) (0.2) (0.2) (0.2) (0.1) B2 3.5 2.8 1.9 0.8 2.2 D2E 7.3 4.3 1.8 1.3 2.4 D3L 7.3 4.3 2.8 1.3 * 40 1 0.2:B2 B2 150 (unit: mm) 2.4 2 0.1:D2E,B2 * 10 B2 B15G,D2E 220 B2,D2E D2E D2E 330 D2E D3L D3L 470 D2E D3L 680 D3L RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor Characteristics List Size SANYO code Part number E.S.R. Maximum allowable Rated Rated Rated Category Category L.C. MSL D.F. ripple current Voltage Temperature Capacitance Voltage Temperature (A) (mmax.) (mArms) Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*1 Temp. 260C 250C B15G 6TRG150M 6.3 85 150 5.0 105 10.0 94.5 70 1000 10TRB33M 10.0 105 33 10.0 105 8.0 33.0 70 1100 6TRE100MAZB 6.3 85 100 5.0 105 8.0 63.0 35 1400 6TRB47M 6.3 105 47 6.3 105 8.0 29.6 70 1100 4TRE150MAZB 4.0 85 150 3.2 105 8.0 60.0 35 1400 4TRB68M 4.0 105 68 4.0 105 8.0 27.2 70 1100 2R5TRE220MAZB 2.5 85 220 2.0 105 8.0 55.0 35 1400 10TRE68M 10.0 105 68 10.0 105 10.0 68 25 2400 6.3 105 220 6.3 105 10.0 138.6 25 2400 18 2800 25 2400 25 2400 4TRE220MI 18 2800 2R5TRE470M 25 2400 15 3100 2R5TRE470MC 12 3500 2R5TRE330M 25 2400 15 3100 2R5TRE330MC 12 3500 2R5TRE220M 25 2400 15 3100 12 3500 25 2400 25 2400 18 2800 25 2400 25 2400 15 3100 B2 6TRE220M 6TRE220MI 6TRE150M 4TRE220M D2E 2R5TRE470MF 2R5TRE330MF 2R5TRE220MF 6.3 105 150 6.3 105 10.0 94.5 4.0 105 220 4.0 105 10.0 88 2.5 2.5 2.5 105 105 105 470 330 220 2.5 2.5 2.5 105 105 105 10.0 10.0 10.0 117.5 82.5 55 2R5TRE220MC 6TRE330ML 4TRE470ML D3L 6.3 105 330 6.3 105 10.0 207.9 4.0 105 470 4.0 105 10.0 188 4TRE470MIL 4TRE330ML 2R5TRE680ML 2R5TRE680MFL 4.0 105 330 4.0 105 10.0 132 2.5 105 680 2.5 105 10.0 170 3 3 2a *1 100k to 500kHz,45C T R 41 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor TQCSeries High Voltage Products Fe a tu re TQC series is perfect for high voltage, low ESR and low profile applications. It is the most suitable for pass-con of the motor driver by 12V, the input of the DCDC converter. Peak temperature 250C lead free reflow soldering products. (See P17) Please contact us, if your reflow condition exceeds this condition. * Specifications Items Condition Operating Temperature range Rated capacitance range Capacitance tolerance Rated voltage Dissipation Factor (D.F.) Leakage current (A) Equivalent series resistance (E.S.R. mmax.) Temperature characteristics of Impedance ratio -- 120Hz/20C 120Hz/20C -- 120Hz/20C Rated voltage applied, after 5 minutes 100kHz/20C Characteristics 100kHz/+20C 105C,2000h 25TQC15M,25TQC22M (category voltage applied), 20TQC22M,16TQC33M,16TQC47M (rated voltage applied) Endurance -55 to +105 (C) 5.6 to 68 (F) _ 20% M:+ 16 to 25 (V.DC) 10.0 (%) 0.1CV B2size: 0.3CV Please see the attached characteristics list -55C Z/Z20C 1.0 to 2.0 +105C 0.6 to 1.0 Z/Z20C _ 20% of the initial value C/C Within+ * tan 105C,1000h 25TQC5R6M,25TQC33M,25TQC22MV,25TQC15MV,25TQC10M (category voltage applied), 20TQC8R2M,20TQC47M,16TQC10M,16TQC68M,20TQC15M,16TQC22M, 20TQC22MV,20TQC33MV,16TQC33MV,16TQC47MV (rated voltage applied) Damp heat (Steady state) 60C,90to95%RH,500h, No voltage applied Surge 15to35C,1000 times, 1kdischarge resistance, surge voltage applied 1.5 times the initial limit L.C. C/C tan L.C. C/C tan L.C. The initial limit Within+40%, -20% of the initial value 1.5 times the initial limit 3 times the initial limit _ 5% of the initial value Within+ The initial limit 3 times the initial limit (unit: mm) Dimensions L*1 (0.2) W (0.2) H*2 (0.1) S (0.2) W1 (0.1) B2 C D2 D3L 3.5 6.0 7.3 7.3 2.8 3.2 4.3 4.3 1.9 2.8 1.9 2.8 0.8 1.3 1.3 1.3 2.2 1.8 2.4 2.4 W L Size code *1 0.3:D3L *2 0.2:C,D3L Size List RV (SV) H F S S 5.6 8.2 10 15 22 33 47 68 W1 Characteristics List Size SANYO code Part number B2 C T Q C D2 D3L 25TQC5R6M 20TQC8R2M 16TQC10M 25TQC10M 20TQC15M 16TQC22M 25TQC22M 25TQC22MV 25TQC15M 25TQC15MV 20TQC22M 16TQC33M 16TQC47M 25TQC33M 20TQC47M 16TQC68M 20 (23) 16 (20) 25 (29) B2 B2 C D2 D2 D3L B2 C D2 C D2 D2 D3L D3L E.S.R. Maximum allowable Rated Category Category L.C. Rated Rated MSL D.F. ripple current (A) (mmax.) (mArms) Voltage Temperature Capacitance Voltage Temperature Reflow Reflow (%max.) Temp. (V) (C) (F) (V) (C) max./5min. 100kHz/20C 100kHz*3 Temp. 260C 250C 25*4 20 16 25*4 20 16 25*4 25*4 25*4 25*4 20 16 16 25*4 20 16 85 105 105 85 105 105 85 85 85 85 105 105 105 85 105 105 5.6 8.2 10 10 15 22 22 22 15 15 22 33 47 33 47 68 20 20 20 20 20 20 20 - 105 105 105 105 105 105 105 - 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 42.0 49.2 48.0 25.0 30.0 35.2 44.0 55.0 38.0 38.0 44.0 52.8 75.2 82.5 94.0 108.8 100 100 100 95 80 80 90 45 90 45 80 70 70 60 55 50 800 800 800 900 1000 1000 1000 1500 1000 1500 1300 1400 1400 1400 1450 1500 Under evaluation 3 *3 100k to 500kHz,105C *4 Please reduce 0.25V per 1C from over 85C for 25V products 42 RoHS compliance Solid Electrolytic Capacitors with Polymerized Organic Semiconductor APC/APDSeries Aluminum Anode Products Fe a tu re AP series is and has a cost performance advantage and low profile by using aluminum foil for the anode. Specifications Items Condition Characteristics -- -55 to +105 (C) Rated capacitance range 120Hz/20C 10 to 33 (F) Capacitance tolerance 120Hz/20C _ 20% M:+ -- 4.0 to 6.3 (V.DC) 120Hz/20C 5.0 or 8.0 (%) Rated voltage applied, after 5 minutes Please see the attached characteristics list Operating Temperature range Rated voltage Dissipation Factor (D.F.) Leakage current Equivalent series resistance (E.S.R. mmax.) Please see the attached characteristics list 100kHz/20C Temperature characteristics of Impedance ratio -55C Z/Z20C +105C Z/Z20C 100kHz/+20C _ 20% of the initial value Within+ D.F. 1.5 times the initial limit L.C. The initial limit C/C Within+40%, -20% of the initial value D.F. 1.5 times the initial limit L.C. 5 times the initial limit C/C _ 5% of the initial value Within+ 60C,90to95%RH,500h, No voltage applied Damp heat (Steady state) 105C,1000 cycles, 1kdischarge resistance, surge voltage applied Surge 0.6 to 1.1 C/C 105C,2000h, rated voltage applied Endurance 0.9 to 2.0 D.F. twice the initial limit L.C. 3 times the initial limit (unit: mm) Dimensions W L Size L W H S W1 code (0.2) (0.2) (0.1) (0.2) (0.1) D1 7.3 4.3 1.4 1.3 2.4 D2 7.3 4.3 1.9 1.3 2.4 Size List RV (SV) F H 10 15 22 33 S S W1 4.0 (5.0) 6.3 (8.0) D1,D2 D1 D2 D2 Characteristics List Series E.S.R. Maximum allowable L.C. Rated Rated Rated Category Category MSL D.F. Size SANYO ripple current (A) (mmax.) (mArms) Voltage Temperature Capacitance Voltage Temperature Reflow Reflow (%max.) code Part number Temp. (V) (C) (F) (V) (C) max./5min.100kHz/20C 100kHz*1 Temp. 260C 250C 6APD10M 4APD15M 6APC22M APC D2 6APC10M 4APC33M APD D1 6.3 4.0 6.3 6.3 4.0 105 105 105 105 105 10 15 22 10 33 6.3 4.0 6.3 6.3 4.0 105 105 105 105 105 8.0 8.0 5.0 8.0 5.0 2.5 2.4 13.9 6.3 13.2 70 70 40 70 40 1900 1900 1900 1900 1900 5 Under evaluation A P C / A P D 4 *1 100k to 500kHz,45C 43 SANYO Electric Co., Ltd. Electronic Device Company Sales division(Japan) 1-1 SANYO-cho, Daito, Osaka, 574-8534 Phone: (072)870-6375/6377 FAX: (072)870-1174 http://www.edc.sanyo.com SANYO Component Europe GmbH Stahlgruberring 4, 81829 Munich Germany Phone: 49-(0)89-460095-284 FAX: 49-(0)89-460095-275 Korea office 9th Floor, Han-Lim Building 146-7, Ssanglim-Dong, Chung-Gu Seoul, Korea Phone: 82-2-2273-5861 FAX: 82-2-2273-6053 SANYO Electronic Device (U.S.A.) Corporation San Diego Headquarter 2055 SANYO Ave., San Diego, CA 92154, U.S.A. Phone: 1-619-661-6835 FAX: 1-619-661-1055 http://www.sanyodevice.com San Jose sales office 1230 Oakmead Parkway, Ste. #314, Sunnyvale, CA 94085, U.S.A. Phone: 1-408-749-9714 FAX: 1-408-749-0212 Dallas sales office 2600 Network Blvd. 6F. Frisco TX. 75034, U.S.A. Phone: 1-469-362-5465 FAX: 1-469-362-5463 Detroit sales office 27000 Meadowbrook Rd., Suite 210 Novi, MI 48377, U.S.A. Phone:1-248-344-1245 FAX: 1-248-479-0428 Hartford sales office P.O.Box 76 Waterford. CT 06385, U.S.A. Phone:1-860-447-9553 FAX1-860-447-9573 Atlanta sales office P.O. Box 70666, Marietta, GA 30007, U.S.A. Phone:1-770-650-5654 FAX: 1-770-640-5081 SANYO Electronic Components (Singapore) Pte., Ltd. 70 Anson Road #19-01 To 08, Apex Tower Singapore/079905/Singapore Phone: 65-6223-0225 FAX: 65-6223-0986 SANYO Electronic Components (H.K.) Ltd. http://www.sanyochina.com Hong Kong Headquarter Suite 3601-06, 36/F, Tower 6, The Gateway, Harbour City, 9 Canton Road, T.S.T., Kowloon, Hong Kong. Phone: 852-2366-2577 FAX: 852-2301-2255 Shanghai office Room2107, Ruijin Building, 205 Mao Min Rd.(S), Shanghai, China Phone: 86-21-6415-6669 FAX: 86-21-6445-8543 Shenzhen office Room301, East Building, High-Tech Plaza, Phase 2, Tian An Cyberpark Futian, Shenzhen, Guangdong China 518040 Phone: 86-755-8835-2319 FAX: 86-755-8835-2324 Beijing office Room708, China Life Tower No.16 Chaoyangmenwai Ave., Beijing, China Phone: 86-10-8525-2600 FAX: 86-10-8525-2602 Taiwan Branch(Taiwan) 10F., No.101, Sec.2, Nanjing E. Rd., Jhongshan District, Taipei City 104, Taiwan (R.O.C.) Phone:886-2-2536-1855 FAX: 886-2-2536-6168 Modifying the subjects and specifications in this catalogue without any notice.