SH18B102M100CT - Walsin Technology Corp.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 1 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

*Contents in this sheet are subject to change without prior notice.

MULTILAYER CERAMIC CAPACITORS

Soft Termination Series

(SH Series) X7R Dielectric

0603 to 1812 Sizes, 10V to 250V

RoHS Compliance

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 2 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

1. INTRODUCTION

WTC soft termination series MLCC is designed and with a polymer layer within end terminations of product, which

can absorb mechanical stress caused by PCB handling in SMT line and reduce the mechanical impact for product. It will

offer more robust and reliable performance in applications.

4. HOW TO ORDER

SH 31 B 104 K 500 C T

Series

SH=Soft

termination

Size

18=0603 (1608)

21=0805 (2012)

31=1206 (3216)

32=1210 (3225)

43=1812 (4532)

Dielectric

B=X7R

Capacitance

Two significant digits

followed by no. of zeros.

And R is in place of

decimal point.

Eg.

104=10x10

4

=100nF

Tolerance

J=±5%

K=±10%

M=±20%

Rated voltage

Two significant

digits followed by

no. of zeros. And

R is in place of

decimal point.

100=10 VDC

160=16 VDC

250=25 VDC

500=50 VDC

101=100VDC

201=200 VDC

251=250 VDC

Termination

C=Cu/Polymer

/Ni/Sn

Packaging

T=7” reeled

G=13” reeled

Note 1: Please see below product range to find right termination code.

2. FEATURES

b. MLCC’s termination are with a soft & flexible

polymer layer to withstand high bending stress in SMT

line.

c. Available for any item in standard series range.

3. APPLICATIONS

a. Automotive industry.

b. Power supply and related industries.

c. Lighting industry.

d. The other mechanical stress concerned products.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 3 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

5. EXTERNAL DIMENSIONS & CONSTRUCTIONS

6. GENERAL ELECTRICAL DATA

Dielectric X7R

Size 0603, 0805, 1206, 1210, 1812

Capacitance* 100pF to 1uF

Capacitance tolerance** J (±5%), K (±10%), M (±20%)

Rated voltage (WVDC) 10V to 250V

Tan δ* Note 1

Insulation resistance at Ur ≥10GΩ or RxC≥100Ω-F whichever is smaller

Dielectric strength ≤100V : ≥2.5 x WVDC ; 200~300V ≥ 2 times VDC

Operating temperature -55 to +125°C

Capacitance characteristic ±15%

* Measured at 1.0±0.2Vrms, 1.0kHz±10% for C≤10µF, 30~70% related humidity, 25°C ambient temperature for X7R

** Preconditioning for Class II MLCC: Perform a heat treatment at 150±10°C for 1 hour, then leave in ambient condition for 24±2 hours

before measurement.

Note 1:

T

W

L

M

B

M

B

Fig. 1 The outline of MLCC

Size

Inch (mm)

L (mm) W (mm) T (mm)/Symbol Remark

M

B

(mm)

1.60±0.20 0.80±0.10

0.80±0.07 S

0603 (1608)

1.60

+0.20/-0.10 0.80

+0.15/-0.10

0.80

+0.15/-0.10 X

0.40±0.15

0.60±0.10 A

0.80±0.10 B

2.00±0.20 1.25±0.10

1.25±0.10 D

#

0805 (2012)

2.00+0.25/-0.2

1.25±0.20

1.25±0.20 I

#

0.50±0.20

0.80±0.10 B

0.95±0.10 C

1.15±0.15 J

#

3.20+0.4/-0.1

1.60±0.15

1.25±0.10 D

#

3.20+0.4/-0.1

1.60±0.20

1.60±0.20 G

#

1206 (3216)

3.20+0.4/-0.1

1.60+0.3/0.1

1.60+0.30/-0.10

P

#

0.60±0.20

0.95±0.10 C

#

3.20±0.40 2.50±0.20

1.25±0.10 D

#

1.60±0.20 G

#

2.00±0.20 K

#

1210 (3225)

3.20±0.50 2.50±0.30

2.50±0.30 M

#

0.75±0.25

1.25±0.10 D

#

3.20±0.30

2.00±0.20 K

#

1812 (4532)

4.50+0.6/-0.4

3.20±0.40

2.50±0.30 M

# 0.75±0.25

# Reflow soldering only is recommended.

Inner electrode

Ceramic

Sn

Cu/Ni

Ag polymer

Metallic

termination

Fig. 2 The construction of S

oft

termination series

MLCC

X7R

Rated

vol. D.F.≦ Exception of D.F. ≦

3%≦

0201(50V); 0603 0.047µF; 0805 0.18µF;1206 0.47µF≧ ≧ ≧

5%≦

1210 4.7µF≧

50V≧

2.5%≦

10%≦

0603 1µF; 0805 1µF;1206 4.7µF; 1210 10µF≧ ≧ ≧ ≧

35V

3.5%≦

10%≦

0805≥2.2µF;

1210 10µF≧

5%≦

0201 0.01µF;0805 1µF; 1210 10µF≧ ≧ ≧

7%≦

0603 0.33µF; 1206 4.7µF≧ ≧

25V 3.5%≦

10≦

%

0402 0.10µF;0603 0.47µF; 0805 2.2µF;1206 6.8µF ; 1210≧ ≧ ≧ ≧

≧

22

µF

5%≦

0201 0.01µF;0402 0.033µF; 0603 0.15µF; 0805 0.68µF;1206 2.2µF;1210 4.7µF≧ ≧ ≧ ≧ ≧ ≧

16V 3.5%≦

10%≦

0402 0.≧

22

uF; 0603 0.68µF;0805 2.2µF;1206 4.7µF;≧ ≧ ≧

1210 22µF≧

10%≦

0

201

0.≧

012

µF;0402 0.33µF;0≧

603 0.33µF; 0805 2.2µF;1206 2.2µF;1210 22µF≧ ≧ ≧ ≧

10V 5%≦

15%≦

0201 0.1µF; 0402 1µF≧ ≧

15%≦

0201 0.1µF;0402 1µF;0603 10µF; 0805 4.7µF;1206 47µF :1210 100µF≧ ≧ ≧ ≧ ≧ ≧

6.3V 10%≦

20%≦

0402 2.2≧

µ

F

4V

15%≦

---

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 4 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

7. CAPACITANCE RANGE (X7R Dielectric)

DIELECTRIC X7R

SIZE 0603 0805

RATED VOLTAGE (VDC)

10 16 25 50 100

200

250

100pF (101)

S S S S S D D D D D D D

120pF (121)

S S S S S D D D D D D D

150pF (151)

S S S S S D D D D D D D

180pF (181)

S S S S S D D D D D D D

220pF (221)

S S S S S D D D D D D D

270pF (271)

S S S S S D D D D D D D

330pF (331)

S S S S S D D D D D D D

390pF (391)

S S S S S D D D D D D D

470pF (471)

S S S S S D D D D D D D

560pF (561)

S S S S S D D D D D D D

680pF (681)

S S S S S D D D D D D D

820pF (821)

S S S S S D D D D D D D

1,000pF (102)

S S S S S D D D D D D D

1,200pF (122)

S S S S S D D D D D D D

1,500pF (152)

S S S S S D D D D D D D

1,800pF (182)

S S S S S D D D D D D D

2,200pF (222)

S S S S S D D D D D D D

2,700pF (272)

S S S S S D D D D D D D

3,300pF (332)

S S S S S D D D D D D D

3,900pF (392)

S S S S S D D D D D D D

4,700pF (472)

S S S S S D D D D D D D

5,600pF (562)

S S S S S D D D D D D D

6,800pF (682)

S S S S S D D D D D D D

8,200pF (822)

S S S S S D D D D D D D

0.010µF (103)

S S S S S D D D D D D D

0.012µF (123)

S S S S D D D D D D D

0.015µF (153)

S S S S D D D D D D D

0.018µF (183)

S S S S D D D D D D D

0.022µF (223)

S S S S D D D D D D D

0.027µF (273)

S S S S D D D D D

0.033µF (333)

S S S X D D D D D

0.039µF (393)

S S S X D D D D D

0.047µF (473)

S S S X D D D D D

0.056µF (563)

S S S X D D D D D

0.068µF (683)

S S S X D D D D D

0.082µF (823)

S S S X D D D D D

0.10µF (104)

S S S X D D D D D

0.12µF (124)

S S X D D D D

0.15µF (154)

S S X D D D D

0.18µF (184)

S S X D D D D

0.22µF (224)

S S X D D D D

0.27µF (274)

X X X I I I

0.33µF (334)

X X X I I I

0.39µF (394)

X X X I I I

0.47µF (474)

X X X I I I

0.56µF (564)

X X I I I

0.68µF (684)

X X I I I

0.82µF (824)

I I I

Capacitance

1.0µF (105)

I I I

1. The letter in cell is expressed the symbol of product thickness.

2. For more information about products with special capacitance or other data, please contact WTC local representative.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 5 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

CAPACITANCE RANGE (X7R Dielectric)

DIELECTRIC X7R

SIZE 1206 1210 1812

RATED VOLTAGE (VDC)

10

16

25

50

100

200

250

10

16

25

50

10

16

25

50

100

200

250

100pF (101)

120pF (121)

150pF (151)

D

180pF (181)

D

220pF (221)

D

270pF (271)

D

330pF (331)

D

390pF (391)

D

470pF (471)

D

560pF (561)

D

680pF (681)

D

820pF (821)

D

1,000pF (102)

D

C

D

1,200pF (122)

D

C

D

1,500pF (152)

D

C

D

1,800pF (182)

D

C

D

2,200pF (222)

D

C

D

2,700pF (272)

D

C

D

3,300pF (332)

D

C

D

3,900pF (392)

D

C

D

4,700pF (472)

D

C

D

5,600pF (562)

D

C

D

6,800pF (682)

D

C

D

8,200pF (822)

D

C

D

0.010µF (103)

D

C

D

0.012µF (123)

D

C

D

0.015µF (153)

D

C

D

0.018µF (183)

D

C

D

0.022µF (223)

D

C

D

0.027µF (273)

D

C

D

0.033µF (333)

D

G

C

D

0.039µF (393)

D

G

C

D

0.047µF (473)

D

G

C

D

0.056µF (563)

D

G

C

D

0.068µF (683)

D

G

C

D

0.082µF (823)

D

G

C

D

0.10µF (104)

D

G

C

D

0.12µF (124)

D

C

D

0.15µF (154)

C

G

C

D

K

0.18µF (184)

C

G

C

D

K

0.22µF (224)

C

G

C

D

K

0.27µF (274)

C

D

C

D

K

0.33µF (334)

C

D

C

D

K

0.39µF (394)

C

J

P

C

D

K

0.47µF (474)

J

J J

P

C

D

K

0.56µF (564)

J

J J

P

D

K

0.68µF (684)

J

J J

P

D

K

0.82µF (824)

J

J J

P

D

K

Capacitance

1.0µF (105)

J

J J

P

D

K

1. The letter in cell is expressed the symbol of product thickness.

2. For more information about products with special capacitance or other data, please contact WTC local representative.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 6 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

8. PACKAGING DIMENSION AND QUANTITY

Paper tape Plastic tape

Size Thickness (mm)/Symbol 7” reel 13” reel 7” reel 13” reel

0.80±0.07 S 4k 15k - -

0603 (1608)

0.80+0.15/-0.10 X 4k 15k - -

0.80±0.10 B 4k 15k - -

1.25±0.10 D - - 3k 10k

0805 (2012)

1.25±0.20 I - - 3k 10k

0.80±0.10 B 4k 15k - -

0.95±0.10 C - - 3k 10k

1.15±0.15 J - - 3K 10K

1.25±0.10 D - - 3k 10k

1.60±0.20 G - - 2k 10k

1206 (3216)

1.60+0.30/-0.10 P - - 2k 9k

0.95±0.10 C - - 3k 10k

1.25±0.10 D - - 3k 10k

1.60±0.20 G - - 2k -

2.00±0.20 K - - 1k 6k

1210 (3225)

2.50±0.30 M - - 1k 6k

1.25±0.10 D - - 1k 5k

2.00±0.20 K - - 1k -

1812 (4532)

2.50±0.30 M - - 0.5k 3k

Unit: pieces

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 7 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

9. RELIABILITY TEST CONDITIONS AND REQUIREMENTS

No.

Item Test Condition Requirements

1.

Visual and

Mechanical --- * No remarkable defect.

* Dimensions to conform to individual specification sheet.

2.

Capacitance * Shall not exceed the limits given in the detailed spec.

3.

Q/ D.F. (Dissipation

Factor)

Class I: NP0

Cap≤1000pF 1.0±0.2Vrms, 1MHz±10%

Cap>1000pF 1.0±0.2Vrms, 1KHz±10%

Class II: X7R,X7E, X5R,Y5V

Cap≤10µF, 1.0±0.2Vrms, 1kHz±10%

**

Cap>10µF, 0.5±0.2Vrms, 120Hz±20%

** Test condition: 0.5±0.2Vrms，1KHz±10%

X7R: 0603≧225(10V),

0805=106(6.3V&10V)

X5R: 01R5≧103, 0201≧224 (6.3V),

0402≧475 (6.3V), 0402≧225(10V),

0603=106 (6.3V),

TT18X≧475(10V) , TT15X series

NP0: Cap≥30pF, Q≥1000; Cap<30pF,Q≥400+20C

X7R, X5R:

Rated

vol. D.F.≦ Exception of D.F. ≦

3%≦

0201(50V); 0603 0.047µF; 0805 0.18µF;1206 0.47µF≧ ≧ ≧

5%≦

1210 4.7µF≧

50V≧

2.5%≦

10%≦

0603 1µF; 0805 1µF;1206 4.7µF; 1210 10µF≧ ≧ ≧ ≧

35V 3.5%≦

10%≦

0805≥2.2µF; 1210 10µF≧

5%≦

0201 0.≧01µF;0805 1µF; 1210 10µF≧ ≧

7%≦

0603 0.33µF; 1206 4.7µF≧ ≧

25V 3.5%≦

10%≦

0402 0.10µF;0603 0.47µF; 0805 2.2µF;≧ ≧ ≧

1206 6.8µF ; 1210≧ ≧22µF

5%≦

0201 0.01µF;0402 0.033µF; ≧ ≧ ≧

0805 0.68µF;1206 2.2µF;1210 4.7µF≧ ≧ ≧

16V 3.5%≦

10%≦

0402 0.≧22uF; 0603 0.68µF;0805 2.2µF≧ ≧ ;

1206 4.7µF;≧ 1210 22µF; TT series ≧

10%≦

0201 0.≧012

µF;0402 0.33µF;0603 0.33µF; 0805 2.2µF;≧ ≧ ≧

1206 2.2µF;1210 22µF; TT series≧ ≧

10V 5%≦ 15%≦

0201 0.1µF; 0402 1µF≧ ≧

15%≦

0201 0.1µF;0402 1µF;0603 10µF; 0805 4.7µF; ≧ ≧ ≧ ≧

1206 47µF :1210 100µF≧ ≧

6.3V 10%≦

20%≦

0402≧2.2µF

4V 15%≦

--- ---

*To apply voltage( 100V) 250%.≦

*Duration: 1 to 5 sec.

*Charge & discharge current less than 50mA.

4a.

Dielectric Strength

*To apply voltage:

200V ~300V & LD series 2 times V DC≧

500V ~ 999V 1.5 times V DC≧

1000V ~ 3000V 1.2 times V DC≧

*Cut-off, set at 10mA

*TEST= 15 sec. *RAMP=0

*No evidence of damage or flash over during test.

4b.

Dielectric Strength

(for X1/Y2 & X2/Y3)

* To apply 1500 VAC voltage.

* Duration: 60 sec. * No evidence of damage or flash over during test.

To apply rated voltage for max. 120 sec. 10GΩ or RxC 500Ω≧-F whichever is smaller.

Class II (X7R, X7E, X5R, Y5V)

Rated voltage Insulation

Resistance

100V: X7R

50V:0603≥1µF;0805≥1µF;1206≥4.7µF;1210≥4.7µF

35V:0805≥2.2µF;1210 10µF≧

25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF

16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF

10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF;

1206≥4.7µF;1210≥47µF

6.3V ; 4V

10GΩ or

RxC 100 Ω≧-

F

whichever is

smaller.

Rated Voltage:

200V ~ 630V To apply rated voltage

(500V max.) for 60 sec.

>10GΩ or 100Ω-F whichever is smaller.

5.

Insulation

Resistance

Rated Voltage:

>630V To apply 500V for 60sec.

>10GΩ

6.

Temperature

Coefficient With no electrical load.

T.C. Operating Temp

NPO (C0G)

-55~125°C at 25°C

NPO (C0H) -55~125°C at 25°C

NPO (C0J) -55~125°C at 25°C

X7R -55~125°C at 25°C

X7E -55~125°C at 25°C

X5R -55~ 85°C at 25°C

Y5V -25~ 85°C at 20°C

T.C. Capacitance Change

NPO (C0G)

Within ±30ppm/°C

NPO (C0H) Within ±60ppm/°C

NPO (C0J) Within ±120ppm/°C

X7R Within ±15%

X7E Within ±4.7%

X5R Within ±15%

Y5V Within +30%/-80%

7.

Adhesive Strength

of Termination

*Pressurizing force：

0201: 2N

0402 & 0603: 5N

>0603: 10N

*Test time：10 ±1 sec

* No remarkable damage or removal of the terminations.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 8 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

No.

Item Test Condition Requirements

8.

Vibration

Resistance * Vibration frequency: 10~55 Hz/min.

* Total amplitude: 1.5mm

* Test time: 6 hrs.

(Two hrs each in three mutually perpendicular directions.)

* Measurement to be made after keeping at room temp. for

24±2 hrs.

* No remarkable damage.

* Cap change and Q/D.F.: To meet initial spec.

9.

Solderability

* Solder temperature: 235±5°C

* Dipping time: 2±0.5 sec. 95% min. coverage of all metalized area.

10.

Bending Test

*The middle part of substrate shall be pressurized by means of

the pressurizing rod at a rate of about 1 mm per second until the

deflection becomes 1 mm / SH series: 5 mm** & 3 mm*** and

then the pressure shall be maintained for 5±1 sec.

*Measurement to be made after keeping at room temp. for 24±2

hrs. (** Thickness >1.0mm; *** Thickness 1.0mm)≦

* No remarkable damage.

* Cap change：

NP0: within ±5% or 0.5pF whichever is larger

X7R, X7E, X5R: within ±12.5% , Y5V: within ±30%

(This capacitance change means the change of capacitance under specified flexure of

substrate from the capacitance measured before the test.)

11.

Resistance to

Soldering

Heat

* Solder temperature: 260±5°C

* Dipping time: 10±1 sec

* Preheating: 120 to 150°C for 1 minute before immerse the

capacitor in a eutectic solder.

* Before initial measurement (Class II only): Perform

150+0/-10°C for 1 hr and then set for 48±4 hrs at room temp.

* Before initial measurement (Class II only): Perform

150+0/-10°C for 1 hr and then set for 24±2 hrs at room temp.

* Measurement to be made after keeping at room temp. for

24±2 hrs.

* No remarkable damage.

* Cap change:

NP0: within ±2.5% or 0.25pF whichever is larger

X7R, X7E, X5R: within ±7.5%

Y5V: within ±20%

* Q/D.F., I.R. and dielectric strength: To meet initial requirements.

* 25% max. leaching on each edge.

12.

Temperature

Cycle * Conduct the five cycles according to the temperatures and time.

Step

Temp. (°C) Time (min.)

1 Min. operating temp. +0/-3 30±3

2 Room temp. 2~3

3 Max. operating temp. +3/-0 30±3

4 Room temp. 2~3

* Before initial measurement (Class II only): Perform

150+0/-10°C for 1 hr and then set for 24±2 hrs at room temp.

* Measurement to be made after keeping at room temp. for 24±2

hrs.

* No remarkable damage.

* Cap change

：

NP0: within ±2.5% or 0.25pF whichever is larger

X7R, X7E, X5R: within ±7.5%

Y5V: within ±20%

* Q/D.F., I.R. and dielectric strength: To meet initial requirements.

13.

Humidity

(Damp Heat)

Steady State

* Test temp.: 40±2°C

* Humidity: 90~95% RH

* Test time: 500+24/-0hrs.

*Before initial measurement (Class II only): Perform 150+0/-

10°C

for 1 hr and then set for 24±2 hrs at room temp.

* Measurement to be made after keeping at room temp. for 24±2

hrs.

* No remarkable damage.

* Cap change: NP0: within ±5% or 0.5pF whichever is larger

X7R, X7E, X5R: ≥10V, within ±12.5%; 6.3V, within ±25%

TT series & C≥ 1uF, within ±25%

Y5V: ≥10V, within ±30%; 6.3V, within +30/-40%

* Q/D.F. value:

NP0: More than 30pF Q≥350, 10pF≤C≤30pF, Q≥275+2.5C,Less than 10pF Q≥200+10C

X7R, X5R:

Rated

vol. D.F.≦

Exception of D.F. ≦

6%≦

0201(50V);0603 0.047µF; 0805 0.18µF; 1206 0.47µF≧ ≧ ≧

10%≦

1210 4.7µF≧

50V≧

3%≦

20%≦

0603 1µF; 0805 1µF;1206 4.7µF; 1210 10µF≧ ≧ ≧ ≧

35V 5%≦

20%≦

0805≥2.2µF;1210 10µF≧

10%≦

0201 0.01µF;0805 1µF; 1210 10µF≧ ≧ ≧

14%≦

0603 0.33µF;1206 4.≧ ≧ 7µF

25V 5%≦

15%≦

0402 0.10µF;0603 0.47µF;0805 2.2µF;1206 6.8µF;≧ ≧ ≧ ≧

1210≧22µF

10%≦

0603 0.15µF;0805 0.68µF;1206 2.2µF;1210 4.7µF≧ ≧ ≧ ≧

16V 5≦％

15%≦

0201 0.01µF;0402 0.033µF;0603 0.68µF;0805 2.2µF;≧ ≧ ≧ ≧

1206 4.7µF; 1210 22µF ≧ ≧

15%≦

0201 0.≧012µF;0402 0.33µF; 0603≧0.33µF;≧

0805 2.2µF≧; 1206 2.2µF; 1210 22µF≧ ≧

10V 7.5%≦

20%≦

0201 0.1µF ;0402 1µF ≧ ≧

6.3V

15%≦

30%≦

0201 0.1µF;0402 1µF;0603 10µF;≧ ≧ ≧

0805 4.7µF;1206 47µF;1210 100µF ≧ ≧ ≧

4V ≦20%

--- ---

*I.R.: ≥10V, 1GΩ or 50 Ω-F whichever is smaller.

Class II (X7R, X7E, X5R, Y5V)

Rated voltage Insulation

Resistance

100V: X7R

50V:0603≥1µF;0805≥1µF;1206≥4.7µF;1210≥4.7µF

35V:0805≥2.2µF;1210≧10µF

25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF

16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF

10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF;

1206≥4.7µF;1210≥47µF

6.3V ; 4V

1GΩ or RxC

≧10 Ω-F

whichever is

smaller.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 9 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

No

Item Test Condition Requirements

14

Humidity

(Damp Heat)

Load

* Test temp.: 40±2°C

* Humidity: 90~95%RH

* Test time: 500+24/-0 hrs.

* To apply voltage：

Rated voltage.(Max.500V)

* Before initial measurement (Class

II only): To apply test voltage for 1hr

at 40

°C

and then set for 24±2 hrs at

room temp.

* Measurement to be made after

keeping at room temp. for 24±2 hrs.

* No remarkable damage.

Cap change: NP0: ±7.5% or 0.75pF whichever is larger.

X7R, X7E, X5R: ≥10V, within ±12.5%; 6.3V, within ±25%, TT series & Cap 1≧µF, within ±25%

Y5V: ≥10V, within ±30%; 6.3V, within +30/-40%

Q/D.F. value: NP0: C≥30pF,Q≥200;C<30pF, Q≥100+10/3C

X7R, X5R:

Rated

vol. D.F.≦

Exception of D.F. ≦

6%≦

0201(50V);0603 0.047µF; 0805 0.18µF; 1206 0.47µF≧ ≧ ≧

10%≦

1210 4.7µF≧

50V≧

3%≦

20%≦

0603 1µF; 0805 1µF;1206 4.7µF; 1210 10µF≧ ≧ ≧ ≧

35V 5%≦

20%≦

0805≥2.2µF;1210 10µF≧

10%≦

0201 0.01µF;0805 1µF; 1210 10µF≧ ≧ ≧

14%≦

0603 0.33µF;1206 4.7µF≧ ≧

25V 5%≦

15%≦

0402 0.10µF;0603 0.47µF;0805 2.2µF;1206 6.8µF;≧ ≧ ≧ ≧

1210≧22µF

10%≦

0603 0.15µF;0805 0.68µF;1206 2.2µF;1210 4.7µF≧ ≧ ≧ ≧

16V 5≦％

15%≦

0201 0.01µF;0402 0.033µF;0603 0.68µF;0805 2.2µF;≧ ≧ ≧ ≧

1206 4.7µF; 1210 22µF ≧ ≧

15%≦

0201 0.≧012µF;0402 0.33µF; 0603 0.33µF;≧ ≧

0805 2.2µF≧; 1206 2.2µF; 1210 22µF≧ ≧

10V 7.5%≦

20%≦

0201 0.1µF ;0402 1µF ≧ ≧

6.3V

15%≦

30%≦

0201 0.1µF;0402 1µF;0603 10µF;≧ ≧ ≧

0805 4.7µF;1206 47µF;1210 100µF ≧ ≧ ≧

4V ≦20%

--- ---

*I.R.: ≥10V, 500MΩ or 25 Ω-F whichever is smaller.

Class II (X7R, X7E, X5R, Y5V)

Rated voltage Insulation

Resistance

100V: X7R

50V:0603≥1µF;0805≥1µF;1206≥4.7µF;1210≥4.7µF

35V:0805≥2.2µF;1210≧10µF

25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF

16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF

10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF;

1206≥4.7µF;1210≥47µF

6.3V ; 4V

500MΩ or

RxC≧5 Ω-F

whichever is

smaller.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 10 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

No

Item Test Condition Requirements

15.

High

Temperature

Load

(Endurance)

*Test temp.

：

NP0, X7R/X7E: 125±3°C

X5R, Y5V: 85±3°C

*Test time: 1000+24/

-0 hrs.

*To apply voltage:

(1) 6.3V or C 10µF≧

or TT series:

150% of rated voltage.

(2) 10V Ur<500V: ≦

200% of rated voltage.

(3) 500V: 150% of rated voltage.

(4) Ur 630V: ≧

120% of rated voltage.

(5) 100% of rated voltage for below

ran

ge.

Size

Dielectric

Rated

voltage Capacitance

range

0201

X5R/X7R

6.3V,10V

C 0.1µF≧

0402

X5R/X7R 6.3V,10V

C 1.0µF≧

0603

X5R/X7R

6.3V,10V

C 4.7µF≧

0805

X5R/X7R

6.3V C 22µF≧

X5R/X7R

6.3V C≧47µF

1206

NP0 3000V C 1.5pF≧

(6)150% of rated voltage for

below

range.

Size

Dielectric

Rated

voltage

Capacitance

range

X5R/X7R

10V,16V,

25V

C≧0.22µF

0402

Y5V 16V C≧0.47µF

X5R/X7R

10V,16V

C 1.0µF≧

0603

Y5V 16V C≧2.2µF

X5R/X7R

10V C 4.7µF≧

0805

Y5V 16V C≧4.7µF

*Before initial measurement (Class II

only): To apply test voltage for 1hr at

test temp. and then set for 24±2 hrs

at room temp.

*Measurement to be made after

keeping at room temp. for 24±2 hrs

* No remarkable damage.

Cap change: NP0: ±3.0% or ±0.3pF whichever is larger

X7R, X7E, X5R: ≥10V, within ±12.5%; 6.3V, within ±25%, TT series & Cap 1≧µF, within ±25%

Y5V: ≥10V, within ±30%; 6.3V, within +30/-40%

Q/D.F. value:

NP0: More than 30pF, Q≥350; 10pF≤C<30pF, Q≥275+2.5C; Less than 10pF, Q≥200+10C

X7R, X5R:

Rated

vol. D.F.≦

Exception of D.F. ≦

6%≦

0201(50V);0603 0.047µF; 0805 0.18µF; 1206 0.47µF≧ ≧ ≧

10%≦

1210 4.7µF≧

5≧0V

3%≦

20%≦

0603 1µF; 0805 1µF;1206 4.7µF; 1210 10µF≧ ≧ ≧ ≧

35V 5%≦

20%≦

0805≥2.2µF;1210 10µF≧

10%≦

0201 0.01µF;0805 1µF; 1210 10µF≧ ≧ ≧

14%≦

0603 0.33µF;1206 4.7µF≧ ≧

25V 5%≦

15%≦

0402 0.1≧0µF;0603 0.47µF;0805 2.2µF;1206 6.8µF;≧ ≧ ≧

1210≧22µF

10%≦

0603 0.15µF;0805 0.68µF;1206 2.2µF;1210 4.7µF≧ ≧ ≧ ≧

16V 5≦％

15%≦

0201 0.01µF;0402 0.033µF;0603 0.68µF;0805 2.2µF;≧ ≧ ≧ ≧

1206 4.7µF; 1210 22µF ≧ ≧

15%≦

0201 0.≧012µF;0402 0.33µF; 0603 0.33µF;≧ ≧

0805 2.2µF≧; 1206 2.2µF; 1210 22µF≧ ≧

10V 7.5%≦

20%≦

0201 0.1µF ;0402 1µF ≧ ≧

6.3V

15%≦

30%≦

0201 0.1µF;0402 1µF;0603 10µF;≧ ≧ ≧

0805 4.7µF;1206 47µF;1210 100µF ≧ ≧ ≧

4V ≦20%

--- ---

*I.R.: ≥10V, 1GΩ or 50 Ω-F whichever is smaller.

Class II (X7R, X7E, X5R, Y5V)

Rated voltage Insulation

Resistance

100V: X7R

50V:0603≥1µF;0805≥1µF;1206≥4.7µF;1210≥4.7µF

35V:0805≥2.2µF;1210≧10µF

25V:0402≥1µF;0603≥2.2µF;0805≥2.2µF;1206≥10µF;1210≥10µF

16V:0402≥0.22µF;0603≥1µF;0805≥2.2µF;1206≥10µF;1210≥47µF

10V:0201≥47nF;0402≥0.47µF;0603≥0.47µF;0805≥2.2µF;

1206≥4.7µF;1210≥47µF

6.3V ; 4V

1GΩ or RxC

≧10 Ω-F

whichever is

smaller.

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 11 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

APPENDIXES

◙ Tape & reel dimensions

Size 0603 0805 1206 1210 1812

Thickness

S, X A B C, D, I B C, J, D G C, D, G

M D, K

A

0

1.02±0.05

1.50±0.10

<1.57 2.00±0.10

<1.85 <1.95 <2.97 <2.97 <3.81

B

0

1.80±0.05

2.30±0.10

<2.40 3.50±0.10

<3.46 <3.67 <3.73 <3.73 <5.30

T 0.95±0.05

0.75±0.05

0.95±0.05

0.23±0.05

0.95±0.05

0.23±0.05

0.25±0.05

K

0

- - - <2.50 - <2.50 <2.50 <2.50 <3.00 <2.50

W 8.00±0.10

8.00±0.10

12.0±0.20

P

0

4.00±0.10

4.00±0.100

4.00±0.10

10xP

0

40.0±0.10

P

1

4.00±0.10

8.00±0.10

P

2

2.00±0.05

D

0

1.55±0.05

1.50±0.05

D

1

- - - 1.00±0.10

- 1.00±0.10

1.00±0.10

1.50±0.10

E 1.75±0.05

1.75±0.05

1.75±0.10

F 3.50±0.05

3.50±0.05

5.50±0.05

Fig. 4 The dimension of plastic tape

Fig. 5 The dimension of reel

Fig. 3 The dimension of paper tape

Size 0402, 0603, 0805, 1206, 1210 1812

Reel size

7” 10” 13” 7”

C 13.0+0.5/-0.2 13.0+0.5/-0.2 13.0+0.5/-0.2 13.0+0.5/-0.2

W

1

8.4+1.5/-0 8.4+1.5/-0 8.4+1.5/-0 12.4+2.0/-0

A 178.0±0.10 250.0±1.0 330.0±1.0 178.0±0.10

N 60.0+1.0/-0 100.0±1.0 100±1.0 60.0+1.0/-0

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 12 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

◙ Description of customer label

◙ Storage and handling conditions

(1) To store products at 5 to 40°C ambient temperature and 20 to 70%. related humidity conditions.

(2) The product is recommended to be used within one year after shipment. Check solderability in case of shelf life

extension is needed.

Cautions: a. The corrosive gas reacts on the terminal electrodes of capacitors, and results in the poor solderability.

Do not store the capacitors in the ambience of corrosive gas (e.g., hydrogen sulfide, sulfur dioxide,

chlorine, ammonia gas etc.)

b. In corrosive atmosphere, solderability might be degraded, and silver migration might occur to cause low

reliability.

c. Due to the dewing by rapid humidity change, or the photochemical change of the terminal electrode by

direct sunlight,the solderability and electrical performance may deteriorate. Do not store capacitors under

direct sunlight or dewing condition. To store products on the shelf and avoid exposure to moisture.

a. Customer name

b. WTC order series and item number

c. Customer P/O

d. Customer P/N

e. Description of product

f. Quantity

g. Bar code including quantity & WTC P/N or customer

h. WTC P/N

i. Shipping date

j. Order bar code including series and item numbers

k. Serial number of label

Approval sheet

Soft Termination_X7R (SH_10V~250V)

Page 13 of 13 ASC_Soft termination_X7R_(SH_10V~250V)_020I_AS Oct. 2012

◙ Recommended soldering conditions

The lead-free termination MLCCs are not only to be used on SMT against lead-free solder paste, but also suitable

against lead-containing solder paste. If the optimized solder joint is requested, increasing soldering time, temperature and

concentration of N

2

within oven are recommended.

Fig. 6 Recommended reflow soldering profile for SMT process

with SnAgCu series solder paste.

4℃

℃℃

℃/ sec max

Over 60sec at least by

natural cooling

4℃

℃℃

℃/ sec max

Over 60sec at least by

natural cooling

Fig. 7 Recommended wave soldering profile for SMT process

with SnAgCu series solder.